Related
Hi, just have a quick question that's been bugging me for a while now. If I have made a full backup using TWRP and I want to restore it, should I:
Fully wipe system and caches and then restore; or just restore right over my current ROM?
****, good question
Sent from my HTC One X using xda app-developers app
Restore takes care of wiping for you.
Piggybacking off the OP, sometimes when I try to restore my TWRP backup it fails, and then the only way I've found to get it working again is to do a boot loader factory reset, and then essentially start from scratch or load an older working backup. No problem, just a minor annoyance. Is there something I'm doing wrong or any advice someone can give me?
Sent from my HTC One X using xda app-developers app
Hydromea said:
Hi, just have a quick question that's been bugging me for a while now. If I have made a full backup using TWRP and I want to restore it, should I:
Fully wipe system and caches and then restore; or just restore right over my current ROM?
Click to expand...
Click to collapse
I always wipe everything before a restore, just in case
Better safe than sorry
Restoring a back up !
When restoring a back up from any recovery wipe everything just as if you were installing a new rom. Factory reset, cache, dalvik cache, system just to be safe. Factory reset wipes data and all cache but not system and if you do a factory reset and then try to wipe I think dalvik again you get an error but no harm done it just will not do it again. I usually do them all and then do the superwipe zip and that willl give you a good piece of mind that it is properly wiped. Also, I have noticed that using the external sd card seems to work best for installing roms or backing up and restoring back ups or anything else like mods or themes. Here is the superwipe zip in case anyone needs it.
Hydromea said:
Hi, just have a quick question that's been bugging me for a while now. If I have made a full backup using TWRP and I want to restore it, should I:
Fully wipe system and caches and then restore; or just restore right over my current ROM?
Click to expand...
Click to collapse
I've done both, but I like not having reinstall all my apps, and reset all my ringtone, and that goes with a full wipe. so when ever i can i flash over. Just make sure your slashing the same rom over the old one.
You shouldn't worry about losing ANYTHING on a backup when you do a factory reset, because the backup houses all of the data and settings anyway.
All you do is Factory Reset, Nandroid>Restore, and your old backup will flash everything the way it was when you did a backup in the first place. Factory Reset is always wise, especially when you're fiddling with different ROM's based on different kernels or systems (AOSP/Sense).
XNine said:
You shouldn't worry about losing ANYTHING on a backup when you do a factory reset, because the backup houses all of the data and settings anyway.
All you do is Factory Reset, Nandroid>Restore, and your old backup will flash everything the way it was when you did a backup in the first place. Factory Reset is always wise, especially when you're fiddling with different ROM's based on different kernels or systems (AOSP/Sense).
Click to expand...
Click to collapse
Ahh, this is true I recant my statement. I was mistakenly thinking about flashing a new ROM over an older version, not a buck-up. I feel stupid.
when restoring a nandroid if you've got the new HBoot I think you have to restore boot.img separately via fastboot. Is that right?
gunnyman said:
when restoring a nandroid if you've got the new HBoot I think you have to restore boot.img separately via fastboot. Is that right?
Click to expand...
Click to collapse
Nope. I just flashed a bunch of roms yesterday and did restores with no issue. I think if your using the stock rooted 2.2 you are correct, but any other rom a restore works fine.
Not Restoring = Bad Idea
Hydromea said:
Hi, just have a quick question that's been bugging me for a while now. If I have made a full backup using TWRP and I want to restore it, should I:
Fully wipe system and caches and then restore; or just restore right over my current ROM?
Click to expand...
Click to collapse
I have made the mistake of not wiping everything (excluding sd card) when changing ROMs or when restoring from a backup. This may be a little different because it was when I was switching to a new ROM on my brother's phone, but I tried to take the lazy way out and not restore everything. I really didn't feel like redownloading everything. I soon learned that this was a mistake, and his "phone" app suddenly disappeared. He was also unable to send or receive texts. This soon made the process even longer than I wished it to be because I needed to go back and restore everything again and get it back to normal.
Error While Restoring using twrp
I took a back up of everything using TWRP and then when i tried to restored its giving me error while restoring system E:Unable to extract tar archive . Please help
Are you trying to restore a backup from a different version of TWRP? For example, currently running 2.7.0.8 but backup was originally made using 2.3.3.1?
Sent from my Evita
error on backup restore twrp
hi i have a nexus 4 running 6.0.1 reserection remix, however when i do a backup on twrp then transfer
it to my pc its fine, but when i restore it it not going as a zip and its giving me this error, could not find meta-inf/com/google/android/update-binary' in the zip file. error installing zip file/sdcard/twrp/backups/01c237769c62991c.zip please help, thanks
Become a member of the w
WOW! After a good 3/4 days of frustration, thinking I had ruined my device, I finally got my TWRP backup to restore.
It's my first time using this software and the restoration process is truly amazing. I mean, my test messages were still there, even my browser history and last page loaded up in chrome were still there. I'm blown away.
The strange thing is that It didn't work when all 3 partitions were selected. When I tried it this way (as per the many step by step instructions that I read) my phone would load up a black screen with just the notification bar visible. I'd see my voicemail, sms, wifi and battery icons at the top, but absolutely nothing else except for a myriad of pop ups that read 'Unfortunately [app name] has stopped working'.
So I bit the bullet and did some trial and error with the partitions.
Turns out that when I only selected 2 of the 3 (I believe they were 'Boot', 'Data' and deselected 'System') everything loaded up just as it was before the backup, except there were only the stock apps available and no google services at all. .....Very odd.
So I did the boot to recovery method before turning the phone off (vol. up - Home - Power) which restarted the phone and strangely brought back EVERYTHING as mentioned at the start of this post.
You can probably understand my confusion here and while I'm VERY happy that it all worked out, I don't understand why it worked with only 2 of the partitions but not with the recommended 3 of them?
Can anyone shed any light on this?
---------- Post added at 01:16 PM ---------- Previous post was at 01:02 PM ----------
debmikeshan said:
hi i have a nexus 4 running 6.0.1 reserection remix, however when i do a backup on twrp then transfer
it to my pc its fine, but when i restore it it not going as a zip and its giving me this error, could not find meta-inf/com/google/android/update-binary' in the zip file. error installing zip file/sdcard/twrp/backups/01c237769c62991c.zip please help, thanks
Become a member of the w
Click to expand...
Click to collapse
Hmmm. I'm definitely no pro at this stuff, in fact i'm very new when it comes to using TWRP, but this is what happened with me.
First of all, the backup that I did was simply a folder of files, not zip.
Transferred that do my PC, wiped my phone with TWRP and replaced the backup folder back into the TWRP/Backup folder. However, after reading up on how to restore on about 10 different android sites/forums, only 1 post shared the most vital piece of information.
You folder has to be in the 'serial' number folder that's located in the 'Backup' folder for TWRP.
When I put my backup folder just into the TWRP/Backup folder, the Restore section would only see the folder itself but the partitions were not available/listed for selection.
Once I placed my Backup folder into the TWRP/Backup/e1oog75 (that alphanumeric name is just a random example made for visual clarity) folder, my partitions were visible and available for selection right away.
Hopefully this helps somewhat.
I posted this in Q&A, but no replies led me to post here as well.
Hi. I've been using this Xoom for a couple weeks now, and just started having this problem yesterday.
Before I noticed the promblem I was on EOS 3 Wingman. I had TWRP 2.2.2.0 as recovery.
I wanted to give CM10 nightlies a shot. Downloaded the ROM and GAPPS through Goo. I tried to flash the CM10 ROM and GApps zip through the Goo interface. Xoom rebooted and instead of installing, I just got a contantly repeating error saying the install failed.
Eventually I rebooted the xoom and went into recovery. I tried to wipe data and it said it couldn't be mounted. Same error for wiping system, cache, etc...
Rebooted xoom and the EOS 3 rom was still working fine, I downloaded [Recovery] ClockworkMod 3.2.0.0 (R4c) Modded for Internal media [UPDATED 10/6]" and flash via adb. rebooted to recovery and tried wipe. same issue. nothing could be wiped. everything said "failure mounting <applicable partition>".
I tried flahing rogue recovery and got the same thing. I said screw it and rebooted back into EOS and it's been working fine. EOS was updated last night to 143, so i downloaded and tried to install through goo. I got the repeating errors again. Rebooted into recovery and still got the errors where it seems like none of the partitions are writeable.
I WAS able to install the EOS update directly through recovery.
Has anyone ever seen this behavior before and know how to fix it? I can't even export logs in the 2 CWM recoveries because they fail when trying to write the log file.
If I try to install an update through goo, it reboots to recover and just keeps scrolling "An Update Error has occured".
I can reboot to recovery and install the zip from there directly with no issue.
Here is the log for the failed data wipe...
I:mke2fs command: mke2fs -t ext4 -m 0 /dev/block/mmcblk0p10
mke2fs 1.41.12 (17-May-2010)
/dev/block/mmcblk0p10 is apparently in use by the system; will not make a filesystem here!
E:Unable to format data.
* Verifying filesystems...
I:=> Let's update filesystem types via verifyFst aka blkid, command: 'blkid'.
* Verifying partition sizes...
Ievice has /data/media
I:Total used space on /data is: 5122715648
I:Total in /data/media is: 3962468352
I:Actual data used: 1160247296
du: /data/media/.android_secure: No such file or directory|
once in recovery, if I try to format data, it says "Unable to format data". Log
Well I can't help, I'm in the same boat...hoping to get some insight from any responses you might get.
grey.ghost said:
Well I can't help, I'm in the same boat...hoping to get some insight from any responses you might get.
Click to expand...
Click to collapse
It's extremely unusual to get no responses to an issue like these here at XDA. leads me to believe it might be a very uncommon problem. The folks here are usually on the ball about any issue that has even arisen before.
That being said, I am going to try to flash the stock RUU back on from this link...
http://developer.motorola.com/produ...utm_source=supportforums&utm_term=unlockboard
After I finish, I re-root/unlock.
I'll let you know how it goes.
I'll let you know if I come up with something as well. So far I've managed to erase the sd card and maintain a constant boot loop.
Flashing all of the stock img, relocking, and unlocking again didn't do ****.
Found an original MZ600 SBF, which is what I need for verizon 3g xoom, I'm installing this via RSD Lite to see if it blows away whatever is causing the issue.
I was able to wipe the entire system and use adb to repeat the unlock and root steps. So far so good. I'm using the CWM 3.2.0.0 recovery image right now though. I have at least been able to get into a clean copy of a ROM and no bootloops yet. Can't restore data off old Nandroids, so I'm about to update to the newer CWM based recovery image and see if that will help.
I think I'm OK now.
I installed the SBF. Let all of the OTA updates come in including the ICS update where my 3g stops.
flashed the ROGUE recovery from fastboot.
I was able to format all partitions and install and boot CM9 nightly.
Me too, i was sweating hard for a bit, but was able to go through the entire process from stock, unlock, root, rogue recovery and then flashed CNA. Got that working without boot loops or fc and then advance restored data from a previous nandroid through rogue to get it back. A couple of apps had to be redownloaded from the market, but it looks as if I'm back in business. I want to try TWRP, but every time I do something screws up, so I think I'll stop trying.
Thanks for the help.
grey.ghost said:
Me too, i was sweating hard for a bit, but was able to go through the entire process from stock, unlock, root, rogue recovery and then flashed CNA. Got that working without boot loops or fc and then advance restored data from a previous nandroid through rogue to get it back. A couple of apps had to be redownloaded from the market, but it looks as if I'm back in business. I want to try TWRP, but every time I do something screws up, so I think I'll stop trying.
Thanks for the help.
Click to expand...
Click to collapse
Are you installing Twrp from goo manager. Cause I have not had any issues with the goo manager download. But did have issues with the zip file here on xda. I dont kknow if it is worth a try but that is how I did it.
Sent from my Xoom using xda app-developers app
Well sense this is a twrp related issue I would think u would have asked in my thread where I released the port for twrp to Xoom,
Having said that, at one point n time there was a note n the open about open script recovery. But its is also buried in the thread too. So I will answer your question and also presume a few things... and please correct me if I am wrong anywhere.
Once u set the download path in goo app to /data/media/goomanager/ and downloaded a ROM, clicked flash ROM, and entered recovery once u saw all the E/ update error u manually rebooted the Xoom and did not let the script finish installing the ROM? If I am correct that so far. That's what cause your additional problems. You basically rebooted recover while mid install of a ROM.
Now as stated it the twrp thread for Xoom, these errors are false errors and should be ignored. To add it the reassurance that they are intact false errors, from goo app select to flash a ROM again and simple allow the script to finish and then the tablet will reboot on its own when it is finished with the script. And you will be greeted with your new ROM you just successfully flashed.
Again let me know if I am wrong on assuming you forced a reboot mid install ( aka while u saw all the errors)
Sent from my Nexus 7 using Tapatalk 2
runandhide05 said:
Well sense this is a twrp related issue I would think u would have asked in my thread where I released the port for twrp to Xoom,
Having said that, at one point n time there was a note n the open about open script recovery. But its is also buried in the thread too. So I will answer your question and also presume a few things... and please correct me if I am wrong anywhere.
Once u set the download path in goo app to /data/media/goomanager/ and downloaded a ROM, clicked flash ROM, and entered recovery once u saw all the E/ update error u manually rebooted the Xoom and did not let the script finish installing the ROM? If I am correct that so far. That's what cause your additional problems. You basically rebooted recover while mid install of a ROM.
Now as stated it the twrp thread for Xoom, these errors are false errors and should be ignored. To add it the reassurance that they are intact false errors, from goo app select to flash a ROM again and simple allow the script to finish and then the tablet will reboot on its own when it is finished with the script. And you will be greeted with your new ROM you just successfully flashed.
Again let me know if I am wrong on assuming you forced a reboot mid install ( aka while u saw all the errors)
Sent from my Nexus 7 using Tapatalk 2
Click to expand...
Click to collapse
No, after pushing the TWRP recovery to the Xoom using adp, I would clean install a ROM and get one of two results....1) the ROM would run for a few seconds and then reboot, or 2) the ROM would run, but everything would fc. Fixing permissions, wiping everything, etc., wouldn't help the issue. No matter what I tried under TWRP, those were the results. I ended up having to start from scratch to negate whatever it was that was making the xoom go funky. Once I pushed rogue and followed the same process, I was back in business.
Sent from my Xoom using Tapatalk 2
Hi Folks.
Ok here is my situation, I have a rooted and unlocked TF700.
I flashed Zeus 4 and all worked well, then flashed (after full wipe) PARANOIDANDROID 2.15 and again everything was great,
Yesterday I flashed Baked Bean 4 (again after a full wipe) and apart from some SD issues all seemed ok,
I then decided to restore my TWRP backup of Zeus as I needed to use my 64gig msd card.
After a full wipe and restore Zeus started up but the dpi was messed up (160) I think (way small)
I was seeing loads of FC's and file manager showed my internal SD as being empty. Rebooted to recovery and tried the "Format Data" option
It failed right away with this message "E: Unable to format data."
I have tried flashing the stock .26 rom via TWRP and I have the same issue, dpi set to 160 and internal sd not mounted.
It seems my Internal sd is corrupt
What is the procedure to reformat it via ADB or fastboot? (I have searched but the results I found relate to other devices and I dont want to simply follow instructions that might cause further harm to my TF700)
I have followed the NVflash brick proof procedure and have all relevant files backed up (I did this before flashing the last 2 roms)
Please can some one point me in the right direction
Thanks a lot
Jules
I always wipe cache, system, internal, davic and then do a factory reset.
Sent from my SAMSUNG-SGH-I717 using xda app-developers app
When you said that you tried to flash the stock .26 you meant installing not restoring a backup, right? What rom you have on your device right now?
Pretoriano80 said:
When you said that you tried to flash the stock .26 you meant installing not restoring a backup, right. What rom you have on your device right now?
Click to expand...
Click to collapse
Yip extracted the zip from the zip file and copied it to my ext sd and flashed it via TWRP
I have an unusable Zeus4,
Im about to try a full wipe again and then flash .26 again
EDIT
After flashing .26 and selecting reboot I get the "No OS installed! Are you sure you wish to reboot?" message
Looks like the system partition is corrupted, but i'm not sure. I think you should come here on IRC and maybe someone with more experience will help you - - http://webchat.freenode.net/?channels=asus-transformer
Thanks so much Pretoriano80!
With his help on IRC I was able to solve the problem,
In the end I had to return to complete stock, It seems CM10 caused some problems,
You are a a legend dude Thanks!!
:good:
ZaJules said:
Thanks so much Pretoriano80!
With his help on IRC I was able to solve the problem,
In the end I had to return to complete stock, It seems CM10 caused some problems,
You are a a legend dude Thanks!!
:good:
Click to expand...
Click to collapse
This same thing happened to me with my Prime when I was getting ready to send it off for RMA because of a broken HDMI port. Since I was unlocked I was advised to restore to stock before sending it in. However, before I got the chance to do that I started getting the "E: Unable to format data." error that you were. I ended up erasing all partitions from fastboot and putting a note in the box that it wouldn't boot after an OTA. I managed to get away with it and wasn't charged for fixing it
For future reference it would be really helpful to know how you fixed this. Did you do something like what is in this thread: http://forum.xda-developers.com/showthread.php?t=1803343.
Did you ever figure out how CM10 messed up your Infinity? I was running CM9 on my Prime when I got this error. Thanks!
It's hard to say if it was CM10 (or any other custom rom) or TWRP to mess the things up but we managed to get back to stock by replacing the twrp with CWM recovery and installing a modified .30 update package. Was a tricky one but we didn't had to mess with the partitions and that's good.
Pretoriano80 said:
It's hard to say if it was CM10 (or any other custom rom) or TWRP to mess the things up but we managed to get back to stock by replacing the twrp with CWM recovery and installing a modified .30 update package. Was a tricky one but we didn't had to mess with the partitions and that's good.
Click to expand...
Click to collapse
Why did you switch to CWM? Do you have any thoughts on the advantages and disadvantages of TWRP vs CWM?
paddycr said:
Why did you switch to CWM? Do you have any thoughts on the advantages and disadvantages of TWRP vs CWM?
Click to expand...
Click to collapse
Switched to CWM just to make sure it wasn't twrp recovery that somehow was failing to flash the partitions correctly. Tbh so far both do their job and both share the same limitation so far, meaning both fail to restore the boot partition (kernel) so in order to restore successfully (from a nandroid backup) you need to flash the right kernel after restoring is done. Otherwise i like TWRP better and never had issues with it, but i miss the advanced option from CWM, the one that let you format each partition individually.
Pretoriano80 said:
Switched to CWM just to make sure it wasn't twrp recovery that somehow was failing to flash the partitions correctly. Tbh so far both do their job and both share the same limitation so far, meaning both fail to restore the boot partition (kernel) so in order to restore successfully (from a nandroid backup) you need to flash the right kernel after restoring is done. Otherwise i like TWRP better and never had issues with it, but i miss the advanced option from CWM, the one that let you format each partition individually.
Click to expand...
Click to collapse
I'm not certain what you're referring to here. I've restored many times from different TWRP backups (for each custom rom that successfully boots and is half-decent, I make and keep a backup in case I want to jump around and try new things) and I've never had any issues. I am still on the .26 firmware update because I plan to do the nvflash thing. Are you saying that between Zeus v4 (ICS) and various Jelly Bean roms I've been on the same kernel? I gues I just haven't checked.
Anyway, I really love the TWRP recovery and use it with Xoom and Nexus 7 as well. It's so easy to use and always has been reliable.
okantomi said:
I'm not certain what you're referring to here. I've restored many times from different TWRP backups (for each custom rom that successfully boots and is half-decent, I make and keep a backup in case I want to jump around and try new things) and I've never had any issues. I am still on the .26 firmware update because I plan to do the nvflash thing. Are you saying that between Zeus v4 (ICS) and various Jelly Bean roms I've been on the same kernel? I gues I just haven't checked.
Anyway, I really love the TWRP recovery and use it with Xoom and Nexus 7 as well. It's so easy to use and always has been reliable.
Click to expand...
Click to collapse
For me moving between various roms by just restoring a backup never worked like it should. Let's say i'm on CM10 and i want to restore from a stock rom backup, the restore process is done, after reboot the device gets stuck to the first Asus screen and will stay there. Now if i get back to recovery and flash an update. zip containing the stock kernel the device will boot just fine, so definitely the boot image doesn't get restored in my case (with . 26 bootloader ).
Edit: @okantomi: You are using the internal storage or a MicroSD for backup / restoring? I'm really curious how this could work for some and not work for others, i mean same device, same recovery, same bootloader version...
Pretoriano80 said:
For me moving between various roms by just restoring a backup never worked like it should. Let's say i'm on CM10 and i want to restore from a stock rom backup, the restore process is done, after reboot the device gets stuck to the first Asus screen and will stay there. Now if i get back to recovery and flash an update. zip containing the stock kernel the device will boot just fine, so definitely the boot image doesn't get restored in my case (with . 26 bootloader ).
Edit: @okantomi: You are using the internal storage or a MicroSD for backup / restoring? I'm really curious how this could work for some and not work for others, i mean same device, same recovery, same bootloader version...
Click to expand...
Click to collapse
Ok, I only flash a new zip from the internal storage...made myself a "Flashworthy" folder which I keep stocked with newest versions of roms/gapps. I save my TWRP backups to my external microsdcard, as well as my TiBu backups. I have never had a problem restoring from TWRP this way, honestly.
okantomi said:
Ok, I only flash a new zip from the internal storage...made myself a "Flashworthy" folder which I keep stocked with newest versions of roms/gapps. I save my TWRP backups to my external microsdcard, as well as my TiBu backups. I have never had a problem restoring from TWRP this way, honestly.
Click to expand...
Click to collapse
Well, in this case i really have no clue why restoring works for some users but not for all.Dees_Troy, the dev behind Twrp recovery told me that .26 bootloader is to blame for the recovery failing to restore the boot partition, but looks like you have that bootloader version and restoring works good for you... interesting.
Pretoriano80 said:
Well, in this case i really have no clue why restoring works for some users but not for all.Dees_Troy, the dev behind Twrp recovery told me that .26 bootloader is to blame for the recovery failing to restore the boot partition, but looks like you have that bootloader version and restoring works good for you... interesting.
Click to expand...
Click to collapse
It is a mystery. Is there any other info that might be relevant to see why the difference in results? I ask because I would like to understand this device better, as well as potentially help others.
okantomi said:
It is a mystery. Is there any other info that might be relevant to see why the difference in results? I ask because I would like to understand this device better, as well as potentially help others.
Click to expand...
Click to collapse
I don't know, maybe the twrp version and the backup options, like if you are using compression or not, which partitions do you backup (boot, system, data, recovery, cache)...
Pretoriano80 said:
I don't know, maybe the twrp version and the backup options, like if you are using compression or not, which partitions do you backup (boot, system, data, recovery, cache)...
Click to expand...
Click to collapse
I'm using TWRP 2.2.2.1, I back up boot, system and data only, and I don't use compression.
I am using CM9 ROM, I don't remember which one because I was flashing it a while ago. Something strange happended to it today. When i try to run my phone it gets stuck at CM9 animation. Tried wipes and fixes from recovery but it didn't work. I would do factory reset but i don't want to lose my apps. They are on my sd card mounted as internal with flashed script. I don't know will I lose them? Help me please.
Przeszczep said:
I am using CM9 ROM, I don't remember which one because I was flashing it a while ago. Something strange happended to it today. When i try to run my phone it gets stuck at CM9 animation. Tried wipes and fixes from recovery but it didn't work. I would do factory reset but i don't want to lose my apps. They are on my sd card mounted as internal with flashed script. I don't know will I lose them? Help me please.
Click to expand...
Click to collapse
I don't think that there is any other method so just do a full wipe
and leave in peace AND YA PRESS THANKS
HAPPY NEW YEAR
Make a backup of your current corrupt rom.
Flash same rom again without wiping anything.. see if that works.
If not..you have nandroid backup img.. take out whatever important data you need.
I made backup, flashed rom and phone runs but there is another problem. When I restore apps from my backup they don't work. When viewed from system settings they look like: com.sketchbook 0,00 B and gray icon with sd card. The same happened to superuser app so I don't even have su rights. Do you have any solution for this or I just have to start with new rom?
Use terminal.. type su..
If your root access is broken you have root it again. There are numerous softwares.. use your pc to retrieve your data from nandroid img. Using titanium to backup app from nandroid backup doesnt work.
I just reinstalled superuser app and it's working. Anyway I think I will just flash a new rom.
Przeszczep said:
I just reinstalled superuser app and it's working. Anyway I think I will just flash a new rom.
Click to expand...
Click to collapse
as I was saying
Hey there!
I'm hoping that someone can help me out. My nephew who's a wanna-be geek was going to update my ROM (which didn't to be done really, but he wanted to show me what he was able to do). He went and downloaded the latest CM 11, rebooted and went into TWRP 2.7.0.1, did a factory reset, an advanced wipe, and did the Format Data. When he did that, it got stuck in a loop. Nothing happened. He tried to install the ROM he downloaded, and NOTHING! Long story short, by him doing the Format Data, he wiped out my partitions. TWRP, no matter what I try to do tells me it's unable to mount 'data' or 'media' etc. etc. Which is leading me to believe I have no partitions left. I've tried installing the latest update from Asus, and no dice. I've tried restoring backups that I have on my micro SD, and that's not working.
Can someone please help me and tell me how to fix this? Can I get my partitions back? I'm really hoping that I don't have to send this tablet off to Asus in Dallas, TX to have it repaired.
I'm using a loaner tablet from a rental store, hoping I can get my TF 300 fixed.
Any help is deeply and sincerely appreciated.
Omega
Sent from my SM-P600 using Tapatalk
I was about to suggest you look in the correct forum, but I see you posted there as well. Anyway, your partitions are probably okay, they have just been wiped out, that doesn't mean you lost them. Have you tried reflashing the recovery? Were you able to flash anything with said recovery before that? Wiping the partitions in the recovery shouldn't have any effect on the flashing functionality, no matter which partitions were selected (except for sdcard, since that's where the ZIPs are stored), so there might be a problem with the recovery itself. Are you sure you have the correct one for your device?
Duchman said:
I was about to suggest you look in the correct forum, but I see you posted there as well. Anyway, your partitions are probably okay, they have just been wiped out, that doesn't mean you lost them. Have you tried reflashing the recovery? Were you able to flash anything with said recovery before that? Wiping the partitions in the recovery shouldn't have any effect on the flashing functionality, no matter which partitions were selected (except for sdcard, since that's where the ZIPs are stored), so there might be a problem with the recovery itself. Are you sure you have the correct one for your device?
Click to expand...
Click to collapse
Hey there Duchman ...
Thanks for your reply. I have tried reflashing the recovery like you suggested. And after that tried to reinstall CM11.Afterwards reflashing the recovery it says “Unable to mount data." I don't know if I need to flash a more recent version of TWRP, if that would even help.
Before all of this happened I could flash almost any ROM of my choice as long as it was KitKat supported. All of my backups and restores are kept on my micro SD so they aren't accidentally deleted. As far as I know it's the correct version of TWRP. It's worked for me so far, ever since I updated to KitKat.
Sent from my SM-P600 using Tapatalk
Omega Recon said:
Hey there Duchman ...
Thanks for your reply. I have tried reflashing the recovery like you suggested. And after that tried to reinstall CM11.Afterwards reflashing the recovery it says “Unable to mount data." I don't know if I need to flash a more recent version of TWRP, if that would even help.
Before all of this happened I could flash almost any ROM of my choice as long as it was KitKat supported. All of my backups and restores are kept on my micro SD so they aren't accidentally deleted. As far as I know it's the correct version of TWRP. It's worked for me so far, ever since I updated to KitKat.
Sent from my SM-P600 using Tapatalk
Click to expand...
Click to collapse
You could try flashing a newer recovery first, I think 2.7.1.0 is available for your device. Also try doing a hard reset by cold booting - here's a how-to: https://www.youtube.com/watch?v=oTU38Ewh8qo (wipe the cache afterwards)
If that doesn't help, reverting to stock is probably your best option. Try this: http://forum.xda-developers.com/showthread.php?t=1757077 (be sure to grab the correct firmware and back up your files)
Have you tried installing any other custom ROM? Does it give you the same error when you try to restore your backup?
Here's what I've come across so far. I did the reset, and that did nothing.
Tried to flash the stock version, after a few seconds, TWRP popped up with FAILED.
I've tried flashing Omni ROM. It will flash, load up, and gets stuck at the boot screen or boot animation. This happens with just about every ROM I try to flash.
Been looking for TWRP 2.7.1.0. I'm not seeing it listed on TWRPs site. Where can I get a copy? Thanks!
Sent from my SM-P600 using Tapatalk
Here you go: http://forum.xda-developers.com/showthread.php?t=2772093
Also do try flashing another recovery, PhilZ for instance: http://forum.xda-developers.com/showthread.php?t=2597860
Did you try wiping all of the partitions again?