The focus of this thread is to get 720p playback and camcorder working for desire on Kitkat ROMs.
tytung has successfully got camcorder and 720 playback mp4 for HD2 for Ics, Jellybean and Kitkat. I have manage replicate the code and will try to get it working on desire
I don't owe a desire so will need some user to actively test the ROM and kernel that I will compile and post.
Source code I have take in from spezi git and first working on cm11 ROM then evervolv
Instructions below is taken from spezi77 thread.
Tester should know how to flash kernel or ROM
Also know how to provide kmsg or last_ksmg and logcat
Installation notes
- Rooted
- At least 512mb ext4 sd-ext partition (1024mb recommended)
- Hboot with at least 250mb system partition (If not slimmed) -> please use AlphaRev Jelly Hboot (250/5/182) for best experience
- Use a newer recovery such as 4ext (credits madmaxx82 & jmcclue) or twrp (credits Chromium)
- Full wipe recommended
- Flash ROM
- In case you use Alpha Jelly hboot (250/5/182) flash GApps -- if not then boot ROM and enable A2SD before flashing GApps
- Boot ROM and let it settle down (3-5 min)
- Enable A2SD
Code:
1) run Terminal Emulator
2) type 'su' and press enter
3) allow root access in the popup query
4) type 'a2sd install' and press enter
5) reply to questions in this order
--> y n y (dalvik to card - yes, data to card - no, reboot - yes)
6) that's it
Enable Developer Settings
--> Open up "Settings > About phone" and tapping 7 times on "Build number"
Testing Logs
Download ROM (26Oct2014)
25/Oct/2014 - Above link ROM an kernel boots , 720p works but camcorder doesn't work
26/Oct/2014 - Uploaded new kernel for test. Result=No tested yet See Post
Hopefully the ROM boots fine.
I made the following changes in evervolv qsd8k kernel.
1. Used older venc driver.
2. Change PMEM_ADSP size to 0x02C00000
You can find it in the attached zip on this post. Add these files if
Do the following test.
For Playback 720p
First test playback the smaller resolution video files in Gallery. Playback a smaller resolution media files (mp4) 176 x 144.
If that is successful play this file http://www.h264info.com/clips.html serenity trailer 720p resolution.
Do the following test for camcorder
Open camcorder and record. If it fails go to setting and change audio from aac to amr or vice versa. Try both audtio setting. I have disable all other not working video setting so you will see only m4v
nickleby said:
I've selected the related files to 720p playback because I don't wanna flash a whole ROM for the moment (I can't), and I can confirm that 720p playback works fine (at least under Evervolv, I'm sure it will be fine for CM too). However, I haven't tested camcoder yet, I'll try to compile the kernel right now and test. Thanks macs18max!!!
Edit: I had the chance to flash the complete ROM. 720p works fine. Camcoder using AAC or AMR with MSM_PMEM_ADSP_SIZE = 0x02C00000 doesn't work. Using MSM_PMEM_ADSP_SIZE = 0x03200000 is the same. The phone/camera app hangs after pressing the record button.
Click to expand...
Click to collapse
jukyO said:
Thanks nickelby. @macs18max,
I guess no need for me to test it then?
Sent from my HTC Desire using Tapatalk
Click to expand...
Click to collapse
Good 720p is working. I will compile a new kernel tonight for testing
macs18max said:
Good 720p is working. I will compile a new kernel tonight for testing
Click to expand...
Click to collapse
Ok. Please provide which rom to use with this kernel.
Sent from my unknown using Tapatalk
Wow! Thanks for you work on Desire! If i can help, just ask!
On spezis carbon Rom when you record the video it has a delay in motion but when u stop recording it doesn't save. I don't have the desire working anymore no microusb working.
Sent from my HTC Desire XS using XDA Free mobile app
Please test this kernel. I have made a flashable zip.
But first you will need to have the cm11 test ROM, installed in the first post
EDIT: link removed has error
Then you need to flash the kernel attached in this post
http://forum.xda-developers.com/attachment.php?attachmentid=2985917&stc=1&d=1414337559
Open camcorder and record. If it fails go to setting and change audio from aac to amr or vice versa. Try both audtio setting. I have disable all other not working video setting so you will see only m4v
Report back with logs and kmsg if not working
macs18max said:
Please test this kernel. I have made a flashable zip.
But first you will need to have the cm11 test ROM, installed in the first post
link http://d-h.st/zwo
Then you need to flash the kernel attached in this post
http://forum.xda-developers.com/attachment.php?attachmentid=2985917&stc=1&d=1414337559
Open camcorder and record. If it fails go to setting and change audio from aac to amr or vice versa. Try both audtio setting. I have disable all other not working video setting so you will see only m4v
Report back with logs and kmsg if not working
Click to expand...
Click to collapse
Cannot open
http://d-h.st/zwo
Other host?
Sent from my HTC Desire using Tapatalk
jukyO said:
Cannot open
http://d-h.st/zwo
Other host?
Sent from my HTC Desire using Tapatalk
Click to expand...
Click to collapse
No other host. But wait.. I found that I missed a flag a boardconfig.mk will compile and reupload
macs18max said:
No other host. But wait.. I found that I missed a flag a boardconfig.mk will compile and reupload
Click to expand...
Click to collapse
Code:
Filename: cm11_bravo_camcorder_test.zip
Size: 148.80 MB (156024405 bytes)
Uploaded By: macs18max
[B][SIZE="5"]Uploaded On: 2014-10-25 16:07:28[/SIZE][/B]
Downloaded: 11
MD5 Sum: 09a6b244725b39dbcba01c70cf5acf47
This version has the boardconfig.mk ????
boardconfig.mk?
Download and install this ROM
https://drive.google.com/folderview?id=0B1gea2aywqJYZkxpRGRRVDhJZG8&usp=sharing
Test 720p and camcorder as per instruction as per this post http://forum.xda-developers.com/showpost.php?p=56284038&postcount=2
If still doesnt work, flash this kernel.
http://forum.xda-developers.com/attachment.php?attachmentid=2985917&stc=1&d=1414337559
try again
cool guys! I always wanted someone to port Tytung work as I really wanted stable camera on 4.x roms; I think LaidbackNikez tried to port it but failed. Hope you guys have better luck. Good luck and keep up with the work! I have switched to galaxy s5 recently but I will try to test your work soon my old htc desire
macs18max said:
Please test this kernel. I have made a flashable zip.
But first you will need to have the cm11 test ROM, installed in the first post
EDIT: link removed has error
Then you need to flash the kernel attached in this post
http://forum.xda-developers.com/attachment.php?attachmentid=2985917&stc=1&d=1414337559
Open camcorder and record. If it fails go to setting and change audio from aac to amr or vice versa. Try both audtio setting. I have disable all other not working video setting so you will see only m4v
Report back with logs and kmsg if not working
Click to expand...
Click to collapse
Hi, I cannot have the ROM installed the whole day because I'm busy with an university assigment and basically I need to stay with my current ROM (Evervolv) to have all my information and apps... I tried the kernel with evervolv and camcoder is not working (same behaviour as with your ROM). I saw you've missed a flag in boardconfig.mk when compiling but I'm trying to download the new ROM and it's asking for a permission... I'm going to have like 2 hours free right now, so I can flash the ROM again and test...
nickleby said:
Hi, I cannot have the ROM installed the whole day because I'm busy with an university assigment and basically I need to stay with my current ROM (Evervolv) to have all my information and apps... I tried the kernel with evervolv and camcoder is not working (same behaviour as with your ROM). I saw you've missed a flag in boardconfig.mk when compiling but I'm trying to download the new ROM and it's asking for a permission... I'm going to have like 2 hours free right now, so I can flash the ROM again and test...
Click to expand...
Click to collapse
Sorry first time I'm using google drive. dev host is currently not working.
What kinda of permission is it asking? Do you have any idea what should I do in my end so that others can download from g-drive
macs18max said:
Sorry first time I'm using google drive. dev host is currently not working.
What kinda of permission is it asking? Do you have any idea what should I do in my end so that others can download from g-drive
Click to expand...
Click to collapse
I don't use Google Drive either. When I open the link it says I need permission to access the file. There's a button to request for a permission, I've pressed it and I guess it sends you an email to aprove my request. Somewhere in Google Drive must be an option to make the file available to all public.
macs18max said:
Sorry first time I'm using google drive. dev host is currently not working.
What kinda of permission is it asking? Do you have any idea what should I do in my end so that others can download from g-drive
Click to expand...
Click to collapse
Boys, you need to set request desktop site when downloading from g drive. Click on arrow and then small arrow on top to download.
nickleby said:
I don't use Google Drive either. When I open the link it says I need permission to access the file. There's a button to request for a permission, I've pressed it and I guess it sends you an email to aprove my request. Somewhere in Google Drive must be an option to make the file available to all public.
Click to expand...
Click to collapse
Sent from my HTC Desire using Tapatalk
K here it is on dev host
http://d-h.st/Mkl
Camcoder not working yet... With/without kernel. Now when you press the record button the phone doesn't hang, but it doesn't record any video using AAC or AMR-NB. 720p playback works ok.
nickleby said:
Camcoder not working yet... With/without kernel. Now when you press the record button the phone doesn't hang, but it doesn't record any video using AAC or AMR-NB. 720p playback works ok.
Click to expand...
Click to collapse
Did not log anything, but.
Same as above, with/without kernel files. Once record is pressed, nothing happens.
Mount command in kernel zip is missing "yaffs" in the beginning, before "MTD".
With kernel files flashed, system looks more responsive, at least for me.
Cheers!
Sent from my unknown using Tapatalk
Just had a try..
Funny thing or strange thing happened.
Downloaded rom, installed It, and it worked!!
But only once.. impossible to make it work again.. even with a full wipe and a new installation. Won't work again
Sent from my HUAWEI P7-L10 using XDA Free mobile app
Related
Just share all these with anyone.
All fix included:
New added in v2:
1. A more native fix to USB connection ( moto portal&tool is available now )
2. add imoseyon tweak script
3. improve GPS(add UK/brazil/CH+HK+TW/USA services info)
4. some adjustment on auto brightness
5. fix losing (gapps) icon issue (area related issue, redirect google services in hosts)
6. enable WIFI tethering
7. try to improve battery charging(replacing charge_only_mode)
8. try to improve touch sensitivity (build.prop)
9. clean some system apps/junks ( common/necessary gapps are reserved )
10.update moto IME from GB leak
11.improve network and voice (not sure)
12.fix sensor/GPS crash in 0906 version(replace 2nd-init with RC1.5)
Download Link: http://www.mirrorcreator.com/files/VMXNTP1B/All_in_One_Fix_for_CM7_and_MIUI_v2.0.7z_links
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------
1.bootmenu overclock
2./data formatting and restoring issue on CWM
3.CPU governors
4.light/gravity
5.keyboard mapping (QWERTY/Z)
6.GSM fix
7.keyboard backlight
8.camera upside down
9.dual way call recording
10.soft keyboard half size
11.random SD card mounting issue in CWM
12.charger light
13.compass
14.APN fix
15.share sd card / DATA function in bootmenu
16.300mhz fix
17.stock recovery fix
18.battery jumping
and also include tweaks and optimization：
1.enhanced sms and location info(ch)
2.moto IME
3.tweaks on framework and build.prop
4.optimized auto brightness
5.power profile
6.some scripts from wajk in /system/etc/init.d
7.full Gapps
Unsolved:
1.video decoding/encoding(720p recording)
2.enable 4-lv freq setting in bootmenu( a little edit in overclock.c)
3.share SD/data/system function in bootmenu are still buggy,sometimes is ok, sometimes not.
4.Alt-lock (I thinks we can ingore this)
5.battery charging(im not sure, but someone said the full voltage in stock 2.2 can reach 4200+ and down in 3100, in CM7 it only get 4160 and down in 3300)
Please use winrar3.50+ or latest 7zip to depack it.
Download link: http://www.mirrorcreator.com/files/IYOX37NY/fix-for-CM7_0.7z_links
Amazing share man!!! Thanks a lot!!!
The link does not work for me.
[Failed to open redirect file]
sahilarora911 said:
Amazing share man!!! Thanks a lot!!!
The link does not work for me.
[Failed to open redirect file]
Click to expand...
Click to collapse
My fault. I post the wrong link. I have updated a new one. Try again.
Endless7 said:
My fault. I post the wrong link. I have updated a new one. Try again.
Click to expand...
Click to collapse
Hey Endless, can you post what is missing/still needs fix?
r2beta0 said:
Hey Endless, can you post what is missing/still needs fix?
Click to expand...
Click to collapse
1.video decoding/encoding(720p recording)
2.enable 4-lv freq setting in bootmenu( a little edit in overclock.c)
3.share SD/data/system function in bootmenu are still buggy,sometimes is ok, sometimes not.
4.Alt-lock (I thinks we can ingore this)
5.battery charging(im not sure, but someone said the full voltage in stock 2.2 can reach 4200+ and down in 3100, in CM7 it only get 4160 and down in 3300)
Ah,for 720p recording. Jorixine send me a PM with a possible method. I try,but failed. But I still want to post here.
The fix is somewhere within media_profiles.xml and build.prop
media_profiles.xml can be edited as you please, even for making the HD videos to size lesser than normal
For it to work, in the build.prop you have to change the following:
ro.media.capture.maxres=5m
ro.media.capture.fast.fps=4
ro.media.capture.slow.fps=60
ro.media.enc.hprof.vid.width=1280
ro.media.enc.hprof.vid.height=720
ro.media.capture.flash=led
ro.media.capture.useDFR=1
ro.media.capture.flashIntensity=42
ro.media.capture.torchIntensity=42
ro.media.capture.classification=classE
ro.mot.setuptype=1
ro.media.enc.aud.fileformat=3gp
ro.media.enc.aud.codec=amrnb
ro.media.enc.aud.bps=12200
ro.media.enc.aud.ch=1
ro.media.enc.aud.hz=8000
ro.media.dec.jpeg.memcap=20000000
r,o.media.dec.aud.wma.enabled=1
ro.media.dec.vid.wmv.enabled=1
He insists, recording 720p is working, the thing is that the phone reboots by itself a lot and some of those reboots are even when it never finished loading the OS, its very annoying.
Seems like the key question is to keep playing with these values. Moreover where it says ClassE, because in GB that comes as ClassH, but he changed it.
Maybe somebody with more expertise can playaround with these two files, get the correct configuration and avoid the rebooting issue.
Click to expand...
Click to collapse
Endless7 said:
Ah,for 720p recording. Jorixine send me a PM with a possible. I try,but failed. But I still want to post here.
Click to expand...
Click to collapse
I think we can make it work with the original camera application.<
Hey im the onlyone getting "unsupported compression method" on 7z¿
WeeDv2 said:
I think we can make it work with the original camera application.<
Hey im the onlyone getting "unsupported compression method" on 7z¿
Click to expand...
Click to collapse
Use winrar3.50 or latest 7zip. Because I use highest compress level.
I think I have fix the battery charging issue. Now I am on 4167 at 92%. No jumping during charing.
What about USB not working as in Stock? any update on that? i think its the MotoUSB.apk, ill try replacing it with stock USB.apk from Arg Movistar 2.2.2
(and yeah i already edited MIUI framework-res.apk)
Endless, your framework-res.apk included is the CM7 one right? cuz the one of MIUI usually is about 7 to 8 MB and your is 4/5 MB
WeeDv2 said:
What about USB not working as in Stock? any update on that? i think its the MotoUSB.apk, ill try replacing it with stock USB.apk from Arg Movistar 2.2.2
(and yeah i already edited MIUI framework-res.apk)
Endless, your framework-res.apk included is the CM7 one right? cuz the one of MIUI usually is about 7 to 8 MB and your is 4/5 MB
Click to expand...
Click to collapse
It's CM7 one.
word patch.
Very nice share Endless7 Thanks
Endless7 said:
I think I have fix the battery charging issue. Now I am on 4167 at 92%. No jumping during charing.
Click to expand...
Click to collapse
I too get to somewhere around there while charging but at 100% I get 4169mV I guess, but if I keep charging it after that it drops to 4134 mV something.
And the link is fine now, thanks!!
Endless7 said:
1.video decoding/encoding(720p recording)
2.enable 4-lv freq setting in bootmenu( a little edit in overclock.c)
3.share SD/data/system function in bootmenu are still buggy,sometimes is ok, sometimes not.
4.Alt-lock (I thinks we can ingore this)
5.battery charging(im not sure, but someone said the full voltage in stock 2.2 can reach 4200+ and down in 3100, in CM7 it only get 4160 and down in 3300)
Click to expand...
Click to collapse
So, have media playback besides mp3/mp4 been fixed?
Is this a complete CM7?
Because decompressed its only ~83 MB....
As the title says, they are fixes for applying on a defy's cm7 or miui, to make it work on milestone 2.
It's not a complete ROM.
ah ok and install logically in cwm "apply update from zip" ?
r2beta0 said:
So, have media playback besides mp3/mp4 been fixed?
Click to expand...
Click to collapse
No,this issue is described in 1th point as video decoding.And i think this also cause the 720p problem.
mj084 said:
ah ok and install logically in cwm "apply update from zip" ?
Click to expand...
Click to collapse
No,but you can overwrite cm7 package with this.
overwrite cm7 package with this....how?
This is a snapshot of my work on bringing camera support to Tezet's Milestone2 ICS port.
This is continuation of this thread: http://forum.xda-developers.com/showthread.php?t=1520572
- it's based on CM9 snapshot from March 2nd
- it may contain more (or less) bugs from Tezet's builds. It's simply different, newer etc.
- it should be possible to load this without factory reset on top of Tezet's CM9 builds and the other way around, though the last time I've tried this was early February...
- there's no need to wipe dalvik cache - the update script does this
- the fix for SIM lock pin is not included
- there's no Torch and file manager app. Don't ask
Camera notes:
The work is based on Atrix ICS camera support, with added overlay emulation.
What is working:
live preview
zooming
flash
focus
exposure compensation etc
taking photos
some 3rd party apps (Pano, CameraFX, Barcode scanner)
doesn't crash when enterinng video/panorama mode
generally much more stable
... probably not much more
What is not working:
panorama mode
video recording
a lot more
Other stuff: (compared to previous version)
- bluetooth should be OK (please test)
- aGPS should work
I highly recommend to do a nandroid backup before trying it.
Latest version available at http://code.google.com/p/cm9-milestone2/downloads/list
If your phone is stuck on Google logo, it means you have chosen a wrong version and you need to recover your phone from the SBF file.
Repository:
repo init -u git://github.com/rondoval/android.git -b ics
All the credits go to:
- Tezet, for the Milestone2 port
- tpruvot, Quarx2k, for their tremendous efforts on Defy support (and thus Milestone2)
- whole Atrix-Dev-Team, Raviprasad V Mummidi, zivan56 for their tremendous work on the camera driver
Just backing up my MS2 now. Going to flash it over CM7 Tezet and see how it goes.
Cheers for the efforts
omg thanks ! download...
Sent from my MotoA953 using xda premium
mattyt_491 said:
Just backing up my MS2 now. Going to flash it over CM7 Tezet and see how it goes.
Cheers for the efforts
Click to expand...
Click to collapse
its for CM9....
devilbatghost said:
its for CM9....
Click to expand...
Click to collapse
Actually this would be a good test... I did that in december. I had some issues, bu I think that was mainly due to wrong version of gapps.
If you're still planning to try upgrading from CM7 to CM9: You may need to wipe telephony provider data and deskclock after upgrade.
/data/data/com.android.deskclock/databases/alarms.db
/data/data/com.android.providers.telephony/databases/telephony.db
Please tell us how did it go
hi, rondoval.
chrome beta don't work. can you try to fix it when you have free time? thx.
rondoval said:
Actually this would be a good test... I did that in december. I had some issues, bu I think that was mainly due to wrong version of gapps.
If you're still planning to try upgrading from CM7 to CM9: You may need to wipe telephony provider data and deskclock after upgrade.
/data/data/com.android.deskclock/databases/alarms.db
/data/data/com.android.providers.telephony/databases/telephony.db
Please tell us how did it go
Click to expand...
Click to collapse
I know it is CM9 I said I was flashing (upgarding) FROM CM7.
As per your advice I cleared alarms.db and telephony.db and was going well.
I also was unable to find the fix for the SIM PIN lock, so I just disabled it.
I haven't yet tried the gapps for ICS because the download through multiupload.com is not working (seems as though multiupload in general is down).
I can confirm that the camera works (photos only) and was able to upgrade from CM7 with no issues without wiping my data.
The ROM is smooth and seems to handle most tasks I have thrown at it. However, I am finding 3D performance a bit lesser than that experienced on CM7 (not a major issue).
Cheers.
Good work, thx! Glad to see we have one more dev working on our MS2.
This rom is awesome!!! =D
Someone can upload the Gapps 4.0.3 please ? because the link on the other post is dead.
Thanks in advance
tony_the_unik said:
This rom is awesome!!! =D
Someone can upload the Gapps 4.0.3 please ? because the link on the other post is dead.
Thanks in advance
Click to expand...
Click to collapse
Here's the link to gapps http://goo.gl/krVg1
Thanks for the gapps link.
Out of interest is there a fix for the Sim pin code yet?
Sent from my MotoA953 using XDA
Some news:
First 5sec 480p video recorded.
Going to cinema now, so don't expect a build today.
New patch for 1% step battery counter on this build
rondoval said:
Some news:
First 5sec 480p video recorded.
Going to cinema now, so don't expect a build today.
Click to expand...
Click to collapse
thank you. I am glad to see the video recording fixed
Is there any bug for the touch?
Since when I am touching and holding on the screen, it displays I'm swiping horizontally instead of holding it (I enabled "Show touches" in Development Tools)
I believe i might have run into a bug, Im not sure if anyone has note this bug or not. In the apps menu, if you hold a application, you can drag it to Remove which will uninstall the app normally, however at the moment, dragging it to Remove does nothing. Does anyone have a idea whats wrong?
i have a huge problem. when my phone is booting up, it only shows the google logo, and.. nothing happend. only a black screen with backlights.
if i try the X factory reset, the screen with an exclamation mark pops up -
but if i press the @ key, nothing happen.
if i try to the connect my phone with RSD lite, the bootloader is loading but shows 'battery low
cannot program'
when i was trying to load the ROM my battery was ~50%...
what should i do?
after a few times failing with the @ - it works.. one time..pressed the factory reset - booted up - still bugged with the google boot up logo...
hi, aznsniper
i have the same problem,i have no idea to solve it. sorry... maybe rondoval will fix it in next build.
@jimbo0815
Did you factory wipe, cache wipe and dalvik wipe before installing the rom? If you did, is it possible that you installed the wrong version? Just my 2 cents worth.
aznsniper said:
I believe i might have run into a bug, Im not sure if anyone has note this bug or not. In the apps menu, if you hold a application, you can drag it to Remove which will uninstall the app normally, however at the moment, dragging it to Remove does nothing. Does anyone have a idea whats wrong?
Click to expand...
Click to collapse
ylqiu said:
hi, aznsniper
i have the same problem,i have no idea to solve it. sorry... maybe rondoval will fix it in next build.
Click to expand...
Click to collapse
that's a problem of trebuchet, the launcher. so it has to be fixed there.
but i think should be like that.
Sent from my MB525 using XDA App
Hi everybody!
Today I share my CM7.2 build and the device folder needed for build.
Firstly, here is the flashable zip:
http://depositfiles.com/files/3ppjnzlbd
Just put it to your SD card and flash with CWM.
What works:
- It boots.
- Theme chooser.
- Screenshot.
- Sound playing and recording.
- GPS
- Vibration (Sometimes buggy.)
What doesn't:
- Everything else. (Including for example camera, video player, wifi, bluetooth, network and mobile data, etc.)
It is going to be a very hard work to make it fully functionable. In the followings, I share my CM7.2 (and CM7. It is the same.) device folder. Here is a little readme for building. I assume the devs who are involved in the CM-development already know this (especially the first steps).
- Check out the latest CyanogenMod 7.2 sources:
repo init -u git://github.com/CyanogenMod/android.git -b gb-release-7.2
repo sync
- Put the device files into device/samsung/galaxyr
- Move cyanogen_galaxyr.mk (from the attached zip) into vendor/cyanogen/products directory.
- Open vendor/cyanogen/vendorsetup.sh and add the following line:
'add_lunch_combo cyanogen_galaxyr-eng' (Without quotes)
- Open vendor/cyanogen/AndroidProducts.mk and add the following:
'$(LOCAL_DIR)/cyanogen_galaxyr.mk' (Without quotes)
- Go to your device folder (device/samsung/galaxyr), put your phone on USB and run extract-files.sh
(It is important to run in the device folder, because it works with relative paths!)
(Your phone must have a stock or stock-based rom to copy the necessary proprietary files!)
- In your top CM source dir, execute:
'. build/envsetup.sh' (Without quotes)
- Finally:
'brunch cyanogen_galaxyr-eng' (Without quotes)
- Wait for it to finish. Flash and enjoy!
Here is the link for the GitHub repository:
https://github.com/Adam77Root/android_device_samsung_galaxyr
Some information about the files:
- The files (especially galaxyr.mk) are bloated with options and settings. I have concerns about the usefulness of some of them. We may not need them in a final/stable build.
- The kernel is the stock ZSLE6 kernel.
- gpswrapper, libaudio, libexifa, libjpega and libsensors were copied from c1-common with little modifications.
Some notices I have come across during the development:
- If we set TARGET_HAVE_TEGRA_ERRATA_657451 to true, we get a plenty of segmentation faults. On CM9, I was able to trace back the problem to this setting! CM7 (and obviously 7.2, I didn't tried) doesn't show the segfaults, probably because init and adb can't load. That's why TeamGalaxyR's rom boots to Samsung splash screen. If you try 'adb shell' on that rom, it immediately closes, because it cannot connect. After I had set this option off, I was able to build working images.
I hope other developers will start working on CM as soon as they can. It is a great project. I will also put every effort into this project, but I won't have access to my files for a week from tomorrow. However, I will stay tuned and be able to post here.
I attach two screenshots I took yesterday.
UPDATE:
Epsylon3 made some progress. The most important: Wifi is working now!!
Get it here: http://dedib.ath.cx/galaxyr/
Every modification to devices have risks. Flash this at your own risk!
Have fun and enjoy!
Thanks man (sorry i have no thanks left, i will hit later)
will try this , after i backup...
OMG OMG OMG... Now downloading. Will Flash and Revert with feedback soon... In short Reserved!!!
(⊙o⊙)Android & iOS Superuser!←_←
Ya.. Me too gonna test and feedback.... Reseved for feedback...
EDIT:
Its not working dude...
I flashed it over ZLES6 and also indian one... but it does not boot to the home screen...
And android logo comes up with black background and it just keeps on blinking...
No success on my phone
EDIT:
Sorry for wrong info.. I forgot to completewipe the device.. Its booting fine and the issues above mentioned are present.. however thanks a lot dude......
Hello Adam77Root Will you pls add some screenshot of it
Also Thanks Given
I am sad that i am off the system. Someone flash it and test it. Finally CM7.2 on r. Next would be fully working cm7 and later cm9(i hope.). Thanks given
Sent from my GT-I9103 using xda app-developers app
Thank you everybody! I added two screenshots to the first post.
in the office now,,can't donwload here due to limited downloads here..will test it at homies...:laugh::fingers-crossed::cyclops:
That's one small step for man, one giant leap for mankind. :laugh::laugh:
Adam77Root said:
Hi everybody!
Today I share my CM7.2 build and the device folder needed for build.
Firstly, here is the flashable zip:
http://depositfiles.com/files/3ppjnzlbd
Just put it to your SD card and flash with CWM.
What works:
- It boots.
- Theme chooser.
- Screenshot.
- Sound playing and recording.
- GPS
- Vibration (Sometimes buggy.)
What doesn't:
- Everything else. (Including for example camera, video player, wifi, bluetooth, network and mobile data, etc.)
It is going to be a very hard work to make it fully functionable. In the followings, I share my CM7.2 (and CM7. It is the same.) device folder. Here is a little readme for building. I assume the devs who are involved in the CM-development already know this (especially the first steps).
- Check out the latest CyanogenMod 7.2 sources:
repo init -u git://github.com/CyanogenMod/android.git -b gb-release-7.2
repo sync
- Put the device files into device/samsung/galaxyr
- Move cyanogen_galaxyr.mk (from the attached zip) into vendor/cyanogen/products directory.
- Open vendor/cyanogen/vendorsetup.sh and add the following line:
'add_lunch_combo cyanogen_galaxyr-eng' (Without quotes)
- Open vendor/cyanogen/AndroidProducts.mk and add the following:
'$(LOCAL_DIR)/cyanogen_galaxyr.mk' (Without quotes)
- Go to your device folder (device/samsung/galaxyr), put your phone on USB and run extract-files.sh
(It is important to run in the device folder, because it works with relative paths!)
(Your phone must have a stock or stock-based rom to copy the necessary proprietary files!)
- In your top CM source dir, execute:
'. build/envsetup.sh' (Without quotes)
- Finally:
'brunch cyanogen_galaxyr-eng' (Without quotes)
- Wait for it to finish. Flash and enjoy!
Here is the link for the GitHub repository:
https://github.com/Adam77Root/android_device_samsung_galaxyr
Some information about the files:
- The files (especially galaxyr.mk) are bloated with options and settings. I have concerns about the usefulness of some of them. We may not need them in a final/stable build.
- The kernel is the stock ZSLE6 kernel.
- gpswrapper, libaudio, libexifa, libjpega and libsensors were copied from c1-common with little modifications.
Some notices I have come across during the development:
- If we set TARGET_HAVE_TEGRA_ERRATA_657451 to true, we get a plenty of segmentation faults. On CM9, I was able to trace back the problem to this setting! CM7 (and obviously 7.2, I didn't tried) doesn't show the segfaults, probably because init and adb can't load. That's why TeamGalaxyR's rom boots to Samsung splash screen. If you try 'adb shell' on that rom, it immediately closes, because it cannot connect. After I had set this option off, I was able to build working images.
I hope other developers will start working on CM as soon as they can. It is a great project. I will also put every effort into this project, but I won't have access to my files for a week from tomorrow. However, I will stay tuned and be able to post here.
I attach two screenshots I took yesterday.
Every modification to devices have risks. Flash this at your own risk!
Have fun and enjoy!
Click to expand...
Click to collapse
What doesn't:
- Everything else. (Including for example camera, video player, wifi, bluetooth, network and mobile data, etc.)
if it doesn't work then what use of this rom
azhar.munshi said:
What doesn't:
- Everything else. (Including for example camera, video player, wifi, bluetooth, network and mobile data, etc.)
if it doesn't work then what use of this rom
Click to expand...
Click to collapse
The thread is tagged as [DEV]. It is not a functional rom, only a preview. Don't try it if you don't want.
Sent from my GT-I9103
azhar.munshi said:
What doesn't:
- Everything else. (Including for example camera, video player, wifi, bluetooth, network and mobile data, etc.)
if it doesn't work then what use of this rom
Click to expand...
Click to collapse
First LEARN to appreciate the work man, !!
gearbox87x said:
That's one small step for man, one giant leap for mankind. :laugh::laugh:
Click to expand...
Click to collapse
:good:
Marked as DEV man..
First show some respect. He is trying to do something that Samsung cannot do.
Encourage, but dont ever EVER discourage..
Kudos to the Dev. I will surely test it..
azhar.munshi said:
What doesn't:
- Everything else. (Including for example camera, video player, wifi, bluetooth, network and mobile data, etc.)
if it doesn't work then what use of this rom
Click to expand...
Click to collapse
You have to understand what a huge leap this is in the development of CynaogenMod for our device...
this ROM is obviously not suitable for daily use.... but this ROM gives us a ray of hope that a fully functional CynaogenMod working on our galaxy r is just round the corner.... Kudos to the developer for such an outstanding development and hope he provides a fully functioning CM 7.2 very soon
Sent from my GT-I9103 using xda app-developers app
@OP to get rid of such things better change title as PRE ALPHA or something.
I tested....
i can't wait for the Full release...!!
really appreciable Work man....!
great..
Thank you everybody! If you know somebody, who can help in development, please contact him/her. I will definitely write to Epsylon3. I'm not really familiar on the forum yet.
xlm13x said:
@OP to get rid of such things better change title as PRE ALPHA or something.
Click to expand...
Click to collapse
I append that tag.
gearbox87x said:
I tested....
i can't wait for the Full release...!!
really appreciable Work man....!
Click to expand...
Click to collapse
Thanks! Creating a full/stable release will take a lot of time.
Hey thnx for creating cm 7 for our device. but i see that u r using 2.3.7 as the android version. Cant it be ics. Plz plz try to do this i luve ics and we hv been waiting for ics from a long time.
Android 4.2.2 Jellybean for Defy and Defy+
Mirrors: http://www.uncledan.it/android-files/CM10.1/
Gapps: http://goo.im/gapps
Experimental builds with 3.0.8 kernel:
Not for daily usage!
Download Link: http://quarx2k.ru/cm10.1-nightly-defy+/!!!experimental!!!/
Works: SD-Card, Bluetooth, Torch, Leds, USB all modes, HW Video decoding, Sensors, FM-Radio (only seek stations+RDS), Sound (only speaker).
Not work: Headset, BT-headset, FM-Radio sound, Phone, GPS, Camera, FM-TX, WiFi.
Known problems: Low speed of USB Mass-storage, Display not always wake after sleep, Suspend not work correctly.
Builds on stable 2.6.32 kernel:
Download Link: http://quarx2k.ru/cm10.1-nightly-defy+/2.6.32/
Mirror: http://d-h.st/users/Quarx/?fld_id=14052#files
Problems/TODO:
1. BT-headset has problems.
2 .BT will not work, if FM is enabled.
3. Video recording is not good.
4. Memory leak after some days.
5. Delay on wakeup.
09.04.13: Suspend optimizations.
13.04.13: Fix BT, add Volume Rocker Wake Support and Expanded Desktop preference. 5Ghz WiFi (not tested)
15.04.13: Fix FM-Radio, Add pie controls, TWRP recovery..
11.05.13 Updated USB-Gadget to native for 4.x, fix mtp/ptp/storage/tethering. Removed usb.apk/usbd. Many minor fixes..
16.05.13 Very experimental build, contain a lot of updates from kernels 2.6.33 - 3.1. Increased performance, added swap. Memory management updated to 2.6.39(3.0) state. Some parts updated to 3.1. Blechd0se patches for interactive gov.
07.06.13 Fix 2g/3g data (thanks to Kayant for finding the right way to resolve problem). More safe mount options (should fix problems of random bootloops). Fix Google Messaging service (thanks to ccav2000)
16.06.13 Updated wifi driver & wpa_supplicant, fix bt-tether by @dh.harald. Improvement in interactive governor by @Blechd0se. Updated kernel with some patches from upstream.
09.07.13 Stability fixes. Updated bootmenu. This build not contain ZCache/Zram/Swap. Who want use ZRAM and other experimental features, can install @Blechd0se's kernel
F.A.Q
Coming from CM 10
Do we need to wipe data to update the CM10 build to CM10.1?
Edit: I will try it, btw. thanks Quarx for the awesome work
GUYS u must flash gapps , if u want to go past the setup during first boot
Fire Head said:
Do we need to wipe data to update the CM10 build to CM10.1?
Click to expand...
Click to collapse
Remember that it's not ready for daily use. Nearly everything doesn't work. You have to wipe everything in order to make it boot. And of course, flash gapps too.
how to get pass , the first boot setup ,
the gapps provided is too large for defy's data partition
so cant get specific needed files for setup , can any1 help ??
i still cant get pass the setup
Quarx, I recommend you to post this link to the OP:
FAQ thread for the new CM10.1!
http://forum.xda-developers.com/showthread.php?p=34616788
----
Guys, remember to hit the "newsworthy thread" button on the OP! The world needs to know this!
Okay, the excitement is understandable, but guys, can you keep this thread CLEAN? Express your gratitude with a donation and the Thanks button, not by flooding the thread with delighted squeals. It's development after all.
I hope (in vain though) that this will be the last offtopic post.
Trimis de pe ASUS Transformer Pad TF300T
So for me, after PIN input, it shows "Unfortunately, the process com.google.process.gapps has stopped" and then "Unfortunately, Setup Wizard has stopped" message... and it stays like that even after i press OK! I can access notification bar, but no start screen!
What to do?
Gafanhotz said:
You have to wipe everything in order to make it boot.
Click to expand...
Click to collapse
Not really, installed it over CM10 (with the new GApps) and deleted cache (and dalvik cache). It works
Fire Head said:
Not really, installed it over CM10 and delete cache (and dalvik cache). It works
Click to expand...
Click to collapse
He said on Facebook to wipe data in order to make it work without major problems.
bone101 said:
No Sdcard here
Sent from my MB526 using xda app-developers app
Click to expand...
Click to collapse
That should be in his to do list don't worry. This is something beyond imaginary what we are going to experience. So thank him for what we have. You know about him. He will surely make it stable.
Sent from my MB526 using xda premium
Gafanhotz said:
Quarx, I recommend you to post this link to the OP:
FAQ thread for the new CM10.1!
http://forum.xda-developers.com/showthread.php?p=34616788
----
Guys, remember to hit the "newsworthy thread" button on the OP! The world needs to know this!
Click to expand...
Click to collapse
Can't find that button..maybe it is not available in tapatalk but only in Web visualization?
Hope this thread will be cleaner than 4.1.2 one..guys for support please use faq thread!
System Wizard stopped fixed
After installing CM10.1 with gapps you can't bypass Setup Wizard stopped. How bypass this error: 1.wipe all data 2.install CM10.1 nightly 3.Wipe all data 4.boot in 4.2, it will boot without errors. 5.Install your needed google apps from market. Error caused by gapps (I think its because low space in ROM - installing CM10.1 without gapps i getted only about 15mb free), so if we want to use future ROMS (4.3 - CM11 or CM10.3) we need to resize SystemROM, to resize SROM - we need unlock bootloader, to bypass bl - TI Board Conf tool & 16MB.bin or some future way )
can i install for Defy green lans ??
slon11 said:
can i install for Defy green lans ??
Click to expand...
Click to collapse
Its for Defy and Defy +.
Since we have custom kernel, every build is for both phones, regardless the lenses
Sent from my Balls of Steel
Can someone make audiofix flashable from cwm as temporary solution ? Beside this rom speed is very good
Audio fix CWM flashable ZIP
I made CWM flashable audio fix.
turffe said:
I made CWM flashable audio fix.
Click to expand...
Click to collapse
Yes thanks a lot,but how to mount sdcard to save download from Tapatalk ?
sebx_g1 said:
Yes thanks a lot,but how to mount sdcard to save download from Tapatalk ?
Click to expand...
Click to collapse
SD is mounted, but android is not seeing it as mounted.
Nothing you can do about it..
Sent from my Balls of Steel
***Posting this on behalf of current CM developer for this device***
Source can be found at https://github.com/CyanogenMod
This is a unified build for Moto X
To build CyanogenMod for yourself you can follow http://wiki.cyanogenmod.org/w/Build_for_moto_msm8960dt
If you'd rather not extract files from the latest CyanogenMod build you can add vendor.xml to your .repo/local_manifests folder.
It's been confirmed to work on both the 4.3 and 4.4 bootloaders.
Details on Installing and downloading CyanogenMod can be found here: http://wiki.cyanogenmod.org/w/Moto_msm8960dt_Info
Official nightlies can be downloaded here: http://download.cyanogenmod.org/?device=ghost
Gapps: http://wiki.cyanogenmod.org/w/Gapps
Known Issues: http://wiki.cyanogenmod.org/w/Known_Issues_page_for_moto_msm8960dt
Changelog: http://www.cmxlog.com/11/moto_msm8960dt/
Before you post a bug report:
Please ensure you have done a full wipe of data and formated system under Mounts and Storage.
If you have flashed parts for other versions you may need to do a full flash of the factory software for your model and start clean.
Do not report bugs in nightlies to jira.cyanogenmod.org
Enjoy!
Already known bugs
So, already known bugs:
1. Speakerphone did not work.
2. GPS sometimes do not find satellites.
3. Video camera have only CIF and QVGA resolution of video quallity.
Also, no external audio at all (speaker, ringer, etc) for the xt1030.
Sent from my unknown using Tapatalk
Rottgrub said:
Also, no external audio at all (speaker, ringer, etc) for the xt1030.
Sent from my unknown using Tapatalk
Click to expand...
Click to collapse
Strange. Bootloader unlocked?
da900 said:
Strange. Bootloader unlocked?
Click to expand...
Click to collapse
Yep, unlocked boot loader. It seems to happen with all of the CM11 based ROMs on the Droid Mini.
That said, headphone audio works fine. I haven't tested bluetooth audio, but I can test that later today.
I'd be happy to run any tests, or provide logcat info if you like. Just let me know.
I am not a dev. Post logcat here. Dhacker will see it and will be able to isolate the problem.
Will this work on unlocked xt1055 US cellular CDMA version?
Sent from my XT1055 using Tapatalk
khanapurechait said:
Will this work on unlocked xt1055 US cellular CDMA version?
Sent from my XT1055 using Tapatalk
Click to expand...
Click to collapse
Codename: moto_msm8960dt
Also known as: ghost, obake-maxx
Vendor: Motorola
Release Date: 2013 Aug 23
Carrier: TMobile, International GSM, Verizon, US Cellular, Sprint
From the link in the OP it says it will: http://wiki.cyanogenmod.org/w/Moto_msm8960dt_Info
Hi I'm using the new PA google camera and I found that de back camera has the CIF QVGA and QCIF resolution and front camera has 1080p resolution, this may addres the issues taking videos with the back camera.
Hope this helps to developers.
I'm using Liquid rom right now.
Videocamera fix
Hi, guys and girls. Seems like I have managed to fix video camera to recocord 1080p and 720p videos and also front video camera, wich can record up to 720p now. I was rying to make front camera record also 1080p videos as on stock ROMs it can do so, but did not find a solution at the moment.
Proof is in the screenshots.
How to;
1. Download attached media-profiles.zip and extract xml file
2. Copy to Sdcard
3. Using any root file manager (I use RootExplorer) go to /system/etc
4. Copy downloader media-profiles.xml to this location and agree with the replacement.
5. Set permissions rw--r--r--
6. Reboot
7. Enjoy fully functional AOSP camera
P.S. If anyone is familiar with gerrit and/or github, please, add this fix to msm8960dt cm source code.
P.P.S. Finaly managed to add 1080p front camera recording.
da900 said:
I am not a dev. Post logcat here. Dhacker will see it and will be able to isolate the problem.
Click to expand...
Click to collapse
Appreciate the advice nevertheless.
Motorola driver decided to be a jerk, so the logcat took me longer than expected. This is the xt1030 Droid Mini, unlocked bootloader, running a clean install of CM11, no gapps package, as of a few days ago. Clean booted the phone, played with the volume controls, and sound ringtone selector.
The bug: No external audio at any point. Headphones work, however.
http://pastebin.com/Q4qjZYbv
If someone takes a look, and wants further tests, please let me know. Be happy to dig into the issue.
Cheers!
-- after rooting around --
Looking it over, since it seems to be horking out around here:
Code:
D/ALSADevice( 347): ALSA module opened
D/AudioHardwareALSA( 347): AudioHardware: DLOPEN successful for ACDBLOADER
E/ ( 347): 2 (No such file or directory) opendir /sys/kernel/debug/asoc/msm8960-tabla1x-snd-card/msm8960-snd-card failed
E/ ( 347): failed to get Peek and Poke names
E/ ( 347): [ACDB RTC]->rtc init done!->result [0]
E/ ( 347): [ACDB ACPH]->actp diag init done!
E/ACDB-LOADER( 347): Error: ACDB ANC returned = -8
E/ACDB-LOADER( 347): done with conversion, anc config size is 148
I've included the contents of that directory structure in case it's useful. Looks like the directory it's looking for is at:
/sys/kernel/debug/asoc/msm8960-snd-card
But that's just a guess without looking directly at the code, which I may do.
http://pastebin.com/HdyCwLyx
Rottgrub said:
Appreciate the advice nevertheless.
Motorola driver decided to be a jerk, so the logcat took me longer than expected. This is the xt1030 Droid Mini, unlocked bootloader, running a clean install of CM11, no gapps package, as of a few days ago. Clean booted the phone, played with the volume controls, and sound ringtone selector.
The bug: No external audio at any point. Headphones work, however.
http://pastebin.com/Q4qjZYbv
If someone takes a look, and wants further tests, please let me know. Be happy to dig into the issue.
Cheers!
--
Looking it over, since it seems to be horking out around here:
Code:
D/ALSADevice( 347): ALSA module opened
D/AudioHardwareALSA( 347): AudioHardware: DLOPEN successful for ACDBLOADER
E/ ( 347): 2 (No such file or directory) opendir /sys/kernel/debug/asoc/msm8960-tabla1x-snd-card/msm8960-snd-card failed
E/ ( 347): failed to get Peek and Poke names
E/ ( 347): [ACDB RTC]->rtc init done!->result [0]
E/ ( 347): [ACDB ACPH]->actp diag init done!
E/ACDB-LOADER( 347): Error: ACDB ANC returned = -8
E/ACDB-LOADER( 347): done with conversion, anc config size is 148
I've included the contents of that directory structure in case it's useful. Looks like the directory it's looking for is at:
/sys/kernel/debug/asoc/msm8960-snd-card
But that's just a guess without looking directly at the code, which I may do.
http://pastebin.com/HdyCwLyx
Click to expand...
Click to collapse
Guess I found a solution for you. Open zip with CM11 nightly. Go to system and find a folder called xt1080. Open it. You will see 3 folders. Extarct them. Then using any root file manager copy files from every folder to /sytem/bin, /system/etc, /system/lib. Extracted folders have the same names. Set permissions. Reboot.
da900 said:
Guess I found a solution for you. Open zip with CM11 nightly. Go to system and find a folder called xt1080...
Click to expand...
Click to collapse
Unfortunately, I've already tried those files with no luck. Appreciate the idea though.
Sent from my Xperia Sola using Tapatalk
Rottgrub said:
Unfortunately, I've already tried those files with no luck. Appreciate the idea though.
Sent from my Xperia Sola using Tapatalk
Click to expand...
Click to collapse
Then just extract the same files from your stock ROM.
da900 said:
Then just extract the same files from your stock ROM.
Click to expand...
Click to collapse
Tried that as well, unfortunately.
Sent from my Xperia Sola using Tapatalk
da900 said:
Hi, guys and girls. Seems like I have managed to fix video camera to recocord 1080p and 720p videos and also front video camera, wich can record up to 720p now. I was rying to make front camera record also 1080p videos as on stock ROMs it can do so, but did not find a solution at the moment.
Proof is in the screenshots.
How to;
1. Download attached media-profiles.zip and extract xml file
2. Copy to Sdcard
3. Using any root file manager (I use RootExplorer) go to /system/etc
4. Copy downloader media-profiles.xml to this location and agree with the replacement.
5. Set permissions rw--r--r--
6. Reboot
7. Enjoy fully functional AOSP camera
P.S. If anyone is familiar with gerrit and/or github, please, add this fix to msm8960dt cm source code.
P.P.S. Finaly managed to add 1080p front camera recording.
Click to expand...
Click to collapse
Is this working for anyone else? My camera still just freezes up when you try to record which is why I removed those resolutions.
---------- Post added at 08:27 PM ---------- Previous post was at 08:08 PM ----------
da900 said:
Guess I found a solution for you. Open zip with CM11 nightly. Go to system and find a folder called xt1080. Open it. You will see 3 folders. Extarct them. Then using any root file manager copy files from every folder to /sytem/bin, /system/etc, /system/lib. Extracted folders have the same names. Set permissions. Reboot.
Click to expand...
Click to collapse
Yeah the unified build isn't set up to recognize Droid Mini. Can you send me the output of:
adb shell
Code:
getprop
cat /proc/cmdline
dhacker29 said:
Yeah the unified build isn't set up to recognize Droid Mini. Can you send me the output of:
adb shell
Code:
getprop
cat /proc/cmdline
Click to expand...
Click to collapse
Happily. I appreciate you looking into it. I restored to stock 4.4, added root, and pulled the below:
xt1030 Stock 4.4: getprop
http://pastebin.com/F0AtmxXU
xt1030 stock 4.4: /proc/cmdline
http://pastebin.com/0ELEb8tk
Let me know if you need anything else.
da900 said:
Hi, guys and girls. Seems like I have managed to fix video camera to recocord 1080p and 720p videos and also front video camera, wich can record up to 720p now. I was rying to make front camera record also 1080p videos as on stock ROMs it can do so, but did not find a solution at the moment.
Proof is in the screenshots.
How to;
1. Download attached media-profiles.zip and extract xml file
2. Copy to Sdcard
3. Using any root file manager (I use RootExplorer) go to /system/etc
4. Copy downloader media-profiles.xml to this location and agree with the replacement.
5. Set permissions rw--r--r--
6. Reboot
7. Enjoy fully functional AOSP camera
P.S. If anyone is familiar with gerrit and/or github, please, add this fix to msm8960dt cm source code.
P.P.S. Finaly managed to add 1080p front camera recording.
Click to expand...
Click to collapse
Tried your solution and two things happend to me, the first one is that no longer had wifi and the second one is that did nit work your solution every time I opened the google camera failed.
did I miss something?
have google now?
if google now worked, this rom will be perfect!!!
http://www.cmxlog.com/11/moto_msm8960dt/
TiagoRigueto said:
have google now?
if google now worked, this rom will be perfect!!!
http://www.cmxlog.com/11/moto_msm8960dt/
Click to expand...
Click to collapse
It works and can be installed from google play