Since I've bought my Razr XT925 from an ebay like site where I live, I need to know the following question since I can't find it out anywhere:
How can I know if my unlocked bootloader is a JB or a KK one?
I'm running it with the following specs atm
Kernel 3.0.101-11512-g9511901
[email protected] #1
CM 11 KitKat 4.4.4 11-20140708-UNOFFICIAL(epinter's)-moto_msm8960 (I've read at epinter's OP and it is supposedly to be running on KKBLs only right?)
As a side note, I've tried to flash the moto_msm8960_jbbl version, which has installed without any error msg but, it always fail when I flash Gapps (error 7). It makes me think that Ive a KKbl but after taking a look at the date showing up at my Fastboot data
10.98(*) (sha9d3ad55, 2012-08-30 20:51:00)
Disc Info: 16GB
Device is UNLOCKED, Status Code: 3
it makes me think its not possible...well, as you can see I'm a bit confused here!
Thanks in advance and cheers!
Anyone?!?
Anyone folks?!?
your bootloader is unlocked as you stated it is code 3
And if you had 3.0.101 kernel is because you have jelly bean bootloader..
Kkbl roms has 3.4.x kernel..
Enviado desde mi RAZR HD mediante Tapatalk
hbenz2008 said:
your bootloader is unlocked as you stated it is code 3
Click to expand...
Click to collapse
Thanks for replying and yeah, its unlocked for sure!
JoseBerga said:
And if you had 3.0.101 kernel is because you have jelly bean bootloader..
Kkbl roms has 3.4.x kernel..
Enviado desde mi RAZR HD mediante Tapatalk
Click to expand...
Click to collapse
Thanks for replying...I've thought about that already but my doubt is, if it is running a JBBL, why did I successfully installed the latest Epinters ROM which is supposed to run over KKBL?
...and here is where I'm lost...do I need to upgrade Kernel separately or does the Kernel upgrade come built in into a given 4.4.4 ROM itself?
...anyways, can you lead me to the easiest/safest way to upgrade to a KKBL...and/or upgrade Kernel if needed? ...any tutorial link is more than enough! (I've done some digg job all over the place already but I couldn't find any about my specific questions/doubts!)
Thanks a lot for your time and attention!
Cheers
RMarques said:
Thanks for replying...I've thought about that already but my doubt is, if it is running a JBBL, why did I successfully installed the latest Epinters ROM which is supposed to run over KKBL?
...and here is where I'm lost...do I need to upgrade Kernel separately or does the Kernel upgrade come built in into a given 4.4.4 ROM itself?
...anyways, can you lead me to the easiest/safest way to upgrade to a KKBL...and/or upgrade Kernel if needed? ...any tutorial link is more than enough! (I've done some digg job all over the place already but I couldn't find any about my specific questions/doubts!)
Thanks a lot for your time and attention!
Cheers
Click to expand...
Click to collapse
No, all Epinter's builds are jbbl.. He hasn't build for KKBL at the moment..
Just upload an screenshoot from "About phone" from your actual Rom/Firmware to be sure about your bootloader..
If you want to update to Official KitKat for the new bl you have to install via fastboot/rsdlite one of the firmwares updateable at the moment (Retail Brazil, Retail CEE, Retail Germany). Then, on the first boot, go to "about phone -> updates" and thats all..
Sorry for my English. :silly:
JoseBerga said:
No, all Epinter's builds are jbbl.. He hasn't build for KKBL at the moment..
Just upload an screenshoot from "About phone" from your actual Rom/Firmware to be sure about your bootloader..
If you want to update to Official KitKat for the new bl you have to install via fastboot/rsdlite one of the firmwares updateable at the moment (Retail Brazil, Retail CEE, Retail Germany). Then, on the first boot, go to "about phone -> updates" and thats all..
Sorry for my English. :silly:
Click to expand...
Click to collapse
Thanks again...and np about your english, its as ok as mine!
I guided myself about the KKBL because there's sort of a warning in red colored letters on Epinter OP saying the following:
"This rom requires an unlocked bootloader. Recent versions (July/2014) requires an updated (KitKat) bootloader".
Since the version I'm using is dated July 8th, 2014, I thought it was right in the spot for the KKBL requirement!
Anyways, I'm running it without any issue...or almost any, since the cell phone restarts itself every now and then! So, as you stated above, in order to have a KKBL I need to install one of the updateable firmware options.
It brings some questions to my mind if you'd be so kind to clarify!
1. Are those firmwares you stated above the official ones?
2. Will I lost my root?
3. Will I be able to reinstall my actual Epinters ROM?
4. After the installation, will my new KKBL be unlocked or will I have to unlock it again?
5. Will this procedure change my 6.0.4.4 CWM touch recovey in any way? If not, can I/should I change it to TWRP (I'm looking into changing to TWRP because I've found a tutorial about partitioning my internal SD in order to solve the very well known "not enough memory/space on disk" issue almost all of us have and it's based on the TWRP recovery!)
**Phone info screen shot
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Well...sorry for any noob question/s and again, thanks a lot for your time, attention and wisdom sharing!
Cheers
As I can see on your screenshoot I have not doubts that you have JBBL.. Because you have 3.0.101 kernel build..
Like I said before all KKBL Roms has 3.4.x kernel.. There's no way to have a 3.0.101 kernel version on KKBL roms..
If you just want to update your Rom, you have to install the latest JBBL builds..
(or any other rom that you want with the name moto_msm8960_jbbl)
About your questions:
1. Yes they are official. you can download from here http://sbf.droid-developers.org/
2. Yes,you will loose root, but you have a unlocked bootloader so you can root it again with no mayor problems
3. No, if you update to KKBL you have to use roms for KKBL (or any rom named as Moto_msm8960) Like I said before, epinter just build for jbbl only (for now)..
4. No, if you unlock you bootloader with official motorola website your bootloader hasn't lock anymore..
5. Yes, will erase your custom recovery and you have to install a new recovery for KKBL.. I never have that problem with "not enough memory/space on disk", but I read that sometime LuckyPatcher is who causing that problem.
JoseBerga said:
As I can see on your screenshoot I have not doubts that you have JBBL.. Because you have 3.0.101 kernel build..
Like I said before all KKBL Roms has 3.4.x kernel.. There's no way to have a 3.0.101 kernel version on KKBL roms..
If you just want to update your Rom, you have to install the latest JBBL builds..
(or any other rom that you want with the name moto_msm8960_jbbl)
About your questions:
1. Yes they are official. you can download from here http://sbf.droid-developers.org/
2. Yes,you will loose root, but you have a unlocked bootloader so you can root it again with no mayor problems
3. No, if you update to KKBL you have to use roms for KKBL (or any rom named as Moto_msm8960) Like I said before, epinter just build for jbbl only (for now)..
4. No, if you unlock you bootloader with official motorola website your bootloader hasn't lock anymore..
5. Yes, will erase your custom recovery and you have to install a new recovery for KKBL.. I never have that problem with "not enough memory/space on disk", but I read that sometime LuckyPatcher is who causing that problem.
Click to expand...
Click to collapse
Thanks again mate! I've enough information in order to start from here!
If you dont mind, just in case I have any further doubts, I'd like to have your ok to PM you!
THanks a lot and take care!
RMarques said:
Thanks again mate! I've enough information in order to start from here!
If you dont mind, just in case I have any further doubts, I'd like to have your ok to PM you!
THanks a lot and take care!
Click to expand...
Click to collapse
Yeah dude, no problem! Good luck!
Enviado desde mi RAZR HD mediante Tapatalk
I was taking a look at which ROMs was available at Cyanogen download page and I just recall that I've tried to install a ROM with msm8960jbbl in its filename a while ago and it failed. Due to that I've installed the Epinters ROM im still using today.
I just took a look at my phone info and it doesn't have the msm8960jbbl in its filename as you can see at the screen shot attached.
I don't want to be repetitive nor I'm thinking you are wrong about what you said but you have to agree that something weird is happening here don't you think?
1. That message/warning in the Epinters OP where he warns that all his ROMs made from July 2014 and newer needed to be used with KKBL.
2. What you said that I'd need to download whatever ROM Id like to use as long as it has msm8960 jbbl in its file name.
3. I recall that this was my first shot ( msm8960 jbbl in the ROMs filename) like 2 weeks ago and it failed to flash like 3 times.
4. Epinters ROM doesn't have jbbl in its filename and flashed without any issue.
5. Any nightlies my built in Cyanogen updater is listing available for me to download as an update don't have msm8960jbbl in its filenames.
Maybe it's just me being noob or getting confused...but still...by this pov it sounds odd!
Anyway, sorry for asking that much but I don't want to screw it!
Cheers!
Sent from my RAZR HD using XDA Free mobile app
Related
Hello my favorite Community!!!
The following very simple guide will guide you on how to create a 4.3 Based ROM (Official Android 4.3 Base or the earlier leaks) that will have have fully functional wifi and wifi-related functions. This Guide assumes that you are already in the process of cooking your 4.3 Custom Rom but you realize you dont have wifi, or wifi gets stuck all the time. However, it is also for users who want to experiement themselves because as you will see the changes are really simple. At the end of this Thread im providing a flashable. zip file that fixes the wifi issue on the 4.3 Roms...
UPDATE: As of 26 Oct 2013, unfortunately the following steps STILL NEED TO BE DONE in order for anyone to have fully functional wifi when they cook a custom ROM based on the Official Android 4.3 Base (or the earlier leaks):
Note 1: FOR THE EARLIER 4.3 UNOFFICIAL LEAKS YOU NEED BOTH STEPS 2A & 2B
Note 2: FOR THE OFFICIAL ANDROID 4.3 BASE YOU ONLY NEED TO IMPLEMENT STEP 2B
1. WHAT DO WE NEED
- The 4.3 Leak (either MI8 or the latest MJ3) or the Official Android 4.3 MJ5 Base
- A kernel compiled with the latest 4.3 sources (i.e. either ausdim or Kt kernel)
- A 4.3 GE ROM (I used mine http://forum.xda-developers.com/showthread.php?t=2369922)
- Notepad ++
2. PROCEDURE
A. FIRST CHANGE SOME OF THE BUILD.PROP VALUES (Note: With the official Android 4.3.MJ5 base you can skip this step)
. This way we "trick" the phone into thinking it is a 4.2.2. version. I used parts of the MGA build.prop. I chose MGA because it was the last one without the new bootloader. I tried with MI1 but i didnt get as satisfactory result. Below I show the procedure with pictures
I. ORIGINAL BUILD PROP:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
II. MODIFIED BUILD PROP
B. THEN WE NEED TO TAKE CARE OF SOME WIFI FILES
I. Exctract the 4.3 GE ROM and go to system/etc/wifi. Copy the whole wifi folder and paste it in the system/etc directory of your custom Rom of the 4.3 LEAK.
II. From the GE ROM we need 2 more files: From system/bin the "wlandutservice" and " wpa_supplicant" files. Again copy them to the system/bin directory of your custom Rom of the 4.3 LEAK.
C. THAT'S IT WE ARE FINISHED!!!!!
I trully hope this has been helpful!! This COMMUNITY has offered me so much. I feel like im giving something back. This is not a thread for Q+A and please respect that. I think everything I wrote is self-explanatory....:good::good::good:
If you will publish your 4.3 Roms, please give credits for the wifi fix.... No need to pm me or anything like that
LINK: The WIFI "Trick" in .zip form. Just flash via Recovery to make your 4.3 work http://d-h.st/fS2
Brilliant
Thanks
Sent from my GT-I9505 using XDA
...Yet simple. Good job Friedrich.
Enviado do meu GT-I9505 utilizando Tapatalk
The 4.2.2 wifi files also work on the wifi bug thing on 4.3 it's how i got mine fixed
Sent from my GT-I9505 using xda premium
Great job, thanks for it
And you are right, this forum offered a lot for me too so I help where I can every day too.
XDA and the Community are the Best
Sorry if it's a little bit off-topic but I need to say this
GT-I9505 ~ SlimBean
saywhatt said:
The 4.2.2 wifi files also work on the wifi bug thing on 4.3 it's how i got mine fixed
Sent from my GT-I9505 using xda premium
Click to expand...
Click to collapse
Excellent partner
So, old bootloader, no knox (no counter, so no 0x0 or 0x1), new 4.3 Rom? This will be excellent...
Sent from my GT-I9505 using tapatalk 4
robertogl said:
So, old bootloader, no knox (no counter, so no 0x0 or 0x1), new 4.3 Rom? This will be excellent...
Sent from my GT-I9505 using tapatalk 4
Click to expand...
Click to collapse
yep yep yep
No bootloader, no modem, no knox
Yes 4.3
friedrich420 said:
yep yep yep
No bootloader, no modem, no knox
Yes 4.3
Click to expand...
Click to collapse
You are the man
Sent from my GT-I9505 using tapatalk 4
so users who have old bootloader can use the 4.3 if i'm correct,
well this is a awesome idea, but are they able to change it back to 4.3 in build prop so other apps only for 4.3 will be available? i don't think degrading the "build.prop" to 4.2.2 is the conclution but i might be wrong, so basically those who uses new bootloader can go back to older firmware? am i right?
Amazing. Thank you
Sent from my GT-I9505 now Free
I hate to have to be the one to do this, but because you did not change the modem or the kernel necessarily is any of this a step towards getting 4.3 on the at&t MF3 sgs4? Not enough people got stuck with this firmware for a real definitive answer to be obvious, or maybe it is and I just don't know enough, but any answer is appreciated.
xerythul said:
I hate to have to be the one to do this, but because you did not change the modem or the kernel necessarily is any of this a step towards getting 4.3 on the at&t MF3 sgs4? Not enough people got stuck with this firmware for a real definitive answer to be obvious, or maybe it is and I just don't know enough, but any answer is appreciated.
Click to expand...
Click to collapse
I cant be certain... Unfortunately i know very little about the other S4 variants...
Maybe if you asked this question in the ROM's thread,, you will get a response. Other users with other variants besides the International one have reported success...
Has anyone tested this with MJ5 yet?
Does it allow us to have fully functional root and Permissive SE Linux status? I want to use Titanium Backup and Wanam Xposed Framework to make Touchwiz slightly less vile.
donalgodon said:
Has anyone tested this with MJ5 yet?
Does it allow us to have fully functional root and Permissive SE Linux status? I want to use Titanium Backup and Wanam Xposed Framework to make Touchwiz slightly less vile.
Click to expand...
Click to collapse
On MJ3 yes...
On MJ5... We will know pretty pretty pretty soon (Larry David reference there)
I am testing this now with MJ5, should know something shortly.
Thanks sir for this, you are awesome...
Sorry, but is it possible to list specifically what the builprop changes are in detail (before and after), because I can't really read them well enough from the images, and I am trying to not make any mistakes.
donalgodon said:
Has anyone tested this with MJ5 yet?
Does it allow us to have fully functional root and Permissive SE Linux status? I want to use Titanium Backup and Wanam Xposed Framework to make Touchwiz slightly less vile.
Click to expand...
Click to collapse
TheAxman said:
I am testing this now with MJ5, should know something shortly.
Thanks sir for this, you are awesome...
Click to expand...
Click to collapse
donalgodon said:
Sorry, but is it possible to list specifically what the builprop changes are in detail (before and after), because I can't really read them well enough from the images, and I am trying to not make any mistakes.
Click to expand...
Click to collapse
SCORE WITH MJ5
About your request i need some time mate...
friedrich420 said:
SCORE WITH MJ5
About your request i need some time mate...
Click to expand...
Click to collapse
Sorry to bother you but I am trying to get a straight answer on some threads.
I have KNOX 0x1 and running MJ3 and its perfect.
I don't care about the KNOX thing because I am in the Netherlands and we can take our phones in for service even if knox is tripped.
I want to upgrade to MJ5 but don't want to mess around with Odin,
Is there a chance of making a Recovery flashable ZIP for MJ5?
I am using TWRP and rooted via CF-Autoroot, latest version.
Thanks in advance.
Daruka said:
Sorry to bother you but I am trying to get a straight answer on some threads.
I have KNOX 0x1 and running MJ3 and its perfect.
I don't care about the KNOX thing because I am in the Netherlands and we can take our phones in for service even if knox is tripped.
I want to upgrade to MJ5 but don't want to mess around with Odin,
Is there a chance of making a Recovery flashable ZIP for MJ5?
I am using TWRP and rooted via CF-Autoroot, latest version.
Thanks in advance.
Click to expand...
Click to collapse
If you are on the international variant go to my Rom's thread (Echoe ROm- check my signature) and soon you'll get a present
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Here is the OTA Kitkat 4.4.2 Brazil XT1033 Dual Sim update
Download:
www.mediafire.com/download/qkou2mh3ddftacp/Blur_Version.14.91.9.falcon_umtsds.Brasil.en.BR.zip
Quote:
not work witch cwm or other custom recovery, if tried not working, need stock recovery, and stock rom us.
share it if you find the solution.
Note: Dont worry if dont see icon H+ when you flashes Stock Rom BR, I Test Velocity, is HSPA +. You can see the screenshot int attached.
1.- For Install just flash stock rom IMPORTANT Blur_Version.14.91.9.falcon_umtsds.Brasil.en.BR LINK
2.- Copy the OTA KITKAT 4.4.2 to sdcard or use adb sideload
3.- Apply update from sdcard
4.- Enjoy
Root Working method:
http://forum.xda-developers.com/showthread.php?t=2584210
Creditis OTA Rom: fabiobatera
I was trying to extract the update to share. thank you so much!
what command you used to extract the file?
OTA rom On-line
Hug.
Can I use this on the stock XT1033 Asia ROM?
I need the 4.3 stock kernel... Can someone upload?
r3flux said:
Can I use this on the stock XT1033 Asia ROM?
Click to expand...
Click to collapse
Not only with the firmware Brazil.
Hug.
mascote9rc said:
I was trying to extract the update to share. thank you so much!
what command you used to extract the file?
Click to expand...
Click to collapse
Past cache using the root explorer.
brenopapito said:
I need the 4.3 stock kernel... Can someone upload?
Click to expand...
Click to collapse
Reinstall the firmware 4.3 Brazil
Hug.
fabiobatera said:
Reinstall the firmware 4.3 Brazil
Hug.
Click to expand...
Click to collapse
But I just need the Kernel.
I received the update via OTA, but I use a custom kernel and my device get bootloop when I try to update.
brenopapito said:
But I just need the Kernel.
I received the update via OTA, but I use a custom kernel and my device get bootloop when I try to update.
Click to expand...
Click to collapse
'll level up the kernel to kernel friend
Hug.
Link Kernel 4.3
Extracting the OTA upate file
Hello !
Can anyone guide me as to how do I get the OTA update file when I get an update on my phone.
Thanks:good:
r3flux said:
Can I use this on the stock XT1033 Asia ROM?
Click to expand...
Click to collapse
My Australian-bought XT1033 (dual sim) got Kitkat today.
System version is:
171.44.31.falcon_umtsds.AsiaRetail.en.03
Looking into installing CWM - got adb working so will flash recovery and take a nandroid.
update: bah, just found that unlocking bootloader would void my warranty and requires a unique key from Motorola, so sorry, can't install CWM - phone is too new to void warranty until I'm sure it doesn't have any faults (this is my first non-Nexus phone so didn't realise bootloader unlocking would be so irritating).
edit: lol, looks like its already here on the forums, cool.. http://forum.xda-developers.com/showthread.php?t=2639384
I don´t know why, but my G isn´t installing this update on stock recovery and isn´t upgrading when using OTA updates. It always says that an error occurs, but never show me any error code. Anyone is having this issue?
Another strange thing, is that when I plug my device on my notebook, it doesn´t recognize which version of android I´m running.
I´ve flashed Blur_Version.14.91.9.falcon_umtsds.Brasil.en.BR and stills the same thing. Any help would be great
Thanks in advance.
---------- Post added at 10:54 AM ---------- Previous post was at 10:44 AM ----------
Hi, will this work on locked and unlocked phones?
Doubt
Hi!
Could I use this ROM if I brick my phone? I do really intend to install CM11, but I'm afraid if something goes wrong what should I do. As long as I know, the RSD Lite doesn't recognize our Mogo G, is there another safe (and easy) way to recover our phone as factory default?
Another newbie doubt, if we do install a ROM (let's say, one of the Motorola site - http : // sbf.droid-developers.org / phone.php?device=14 -without spaces]) we will have our bootloader locked back?
Thanks!
biscoitu said:
I don´t know why, but my G isn´t installing this update on stock recovery and isn´t upgrading when using OTA updates. It always says that an error occurs, but never show me any error code. Anyone is having this issue?
Another strange thing, is that when I plug my device on my notebook, it doesn´t recognize which version of android I´m running.
I´ve flashed Blur_Version.14.91.9.falcon_umtsds.Brasil.en.BR and stills the same thing. Any help would be great
Thanks in advance.
---------- Post added at 10:54 AM ---------- Previous post was at 10:44 AM ----------
Hi, will this work on locked and unlocked phones?
Click to expand...
Click to collapse
Hello, have you found a solution? I've got same problem!!!!
linsspinho said:
Hello, have you found a solution? I've got same problem!!!!
Click to expand...
Click to collapse
yes...I´ve flashed stock Blur_Version.14.71.8.falcon_umtsds.Brasil.en.BR, and then updated everything by OTA and now it´s running fine
w0mbl3 said:
My Australian-bought XT1033 (dual sim) got Kitkat today.
System version is:
171.44.31.falcon_umtsds.AsiaRetail.en.03
Looking into installing CWM - got adb working so will flash recovery and take a nandroid.
update: bah, just found that unlocking bootloader would void my warranty and requires a unique key from Motorola, so sorry, can't install CWM - phone is too new to void warranty until I'm sure it doesn't have any faults (this is my first non-Nexus phone so didn't realise bootloader unlocking would be so irritating).
edit: lol, looks like its already here on the forums, cool.. http://forum.xda-developers.com/showthread.php?t=2639384
Click to expand...
Click to collapse
I have the same XT1033 dual sim with 16GB and updated it to KitKat OTA. My Moto G was a grey import (into Australia) destined for India (it came with a Motorola charger and handsfree).
The system version is: 171.44.31.falcon_umtsds.AsiaRetail.en.03. This update does not break USB OTG functionality, it's the same update that was rolled out in India. It now shows OTG capability in Settings > Storage (see the bottom where it says USB Disk). I haven't used it yet, but here's a video below demonstrating it:
https://www.youtube.com/watch?v=9QLD8OknwyM
Here is a request to those that have updated to KitKat, is the OTG working after the update and which version was it?
And can someone upload the "171.44.31.falcon_umtsds.AsiaRetail.en.03.zip" update. I want to unlock and root, but also want to be able to return to the original stock rom later. :angel:
If you haven't updated yet, I think you can pull the file after you've downloaded it from the /Cache/ directory using adb. After downloading it, it will ask you whether to update later, choose later then pull the file to the desktop. I forgot to do this step...
Thanks :victory:
/EDIT
Nevermind, the Motorola naming of updates had me confused. The file that I was after was actually "Blur_Version.14.85.4.falcon_umtsds.AsiaRetail.en.03.zip" which can be found here: http://forum.xda-developers.com/showpost.php?p=49390749&postcount=1
When updated the version and baseband will be:
Baseband: MSM8626BP_1032.355.66.00R
System: 171.44.31.falcon_umtsds.AsiaRetail.en.03
Kernel:3.4.0-g9f5dcdc
Build num:KXB20.25-1.31
http://forum.xda-developers.com/showpost.php?p=50173342&postcount=56
biscoitu said:
yes...I´ve flashed stock Blur_Version.14.71.8.falcon_umtsds.Brasil.en.BR, and then updated everything by OTA and now it´s running fine
Click to expand...
Click to collapse
How did you do this? Is there any tutorial?
Kempf said:
How did you do this? Is there any tutorial?
Click to expand...
Click to collapse
Here is a guide to flash a full ROM:
http://forum.xda-developers.com/showthread.php?t=2542219
After that, you can flash an update OTA or from a zip.
It's not that easy, but it's a tutorial. Thanks!
Kempf said:
It's nota that easy, bit it's a tutorial. Thanks!
Click to expand...
Click to collapse
Just be prepared to do a bit of reading and research on the device and what you want to do with it. After a few years away from all this it can be a little overwhelming for me. If you can understand the process and learn from the mistakes others have made, you'll avoid them yourself. Be patient and think ahead, be sure of what you are doing and why then you won't have too many problems.
DISCLAIMER: I'm not responsible for any damage to your phone, i tested all these files personally before uploading them and I don't have problems, but just in case you cannot blame me for any damage, no one forces you to mod your phone, if you don't want to risk don't do it
I'm here to give you a good news (even if it may be a little late since there will not be new baseband for our device)... I have found the way to flash the baseband in recovery, so from this moment our phone can be completely modded using only recovery mode
First of all I have to say thank you to @alireza7991 and @broodplank1337 because they were the first one to think it could be possible in this way. I have to say thank you to @Rhonin86 for testing help (he has a spare i9001 ) and to @adfree because he posted this http://forum.xda-developers.com/showpost.php?p=52944982&postcount=29
Here is a list of zip files containing basebands, I will update it from time to time
I9001XXKPO (last Italian and German stock firmware no brand)
I9001BUKP7 (last Italian and German stock Vodafone firmware
I9001XXKPM
I9001XXKPL
I9001XXKPF (Stock italian 2.3.5 firmware no brand)
I9001DDKP9 (Last Indian baseband)
I9001XXKG3
me and @Rhonin86 tested this, it works on all custom recoveries
Thanks to:
@alireza7991 and @broodplank1337 for the concept
@Rhonin86 for testing
@adfree for the partition layout and names
I can't provide all the basebands for our phone because on sammomibile there are some rom not available, and they are really a lot so if you want to test a baseband available here, and then have the possibility to come back on the one you are using now and it is not available here this is all what you need.
The backup script take a backup of the current baseband and put it in /sdcard/amss.bak
The restore script flashes the file /sdcard/amss.bak on you baseband, so it restores the backup
WARNING
Dont play with amss.bak file and be sure it is in its place before restoring it
Backup script: http://www.mediafire.com/download/9xdm5rfaoz4x0yd/Backup_Baseband-signed.zip
Restore script: http://www.mediafire.com/download/7tn3dzz2zy9malm/Restore_backup_baseband-signed.zip
good Job brother ,
Yesterday I updated the version XXKPO , I have a lot looking on the net to flash the baseband via recovery, and I finished the update via Odin XD
I hope that can help others members who seek this solution
cordially
Excuse my bad english
esolks said:
good Job brother ,
Yesterday I updated the version XXKPO , I have a lot looking on the net to flash the baseband via recovery, and I finished the update via Odin XD
I hope that can help others members who seek this solution
cordially
Excuse my bad english
Click to expand...
Click to collapse
Sad to know i arrived too late BTW with this method you can easily switch baseband and try them to chose which is better for you
Inviato dal mio GT-I9001 utilizzando Tapatalk
ktulu84 said:
I'm here to give you a good news (even if it may be a little late since there will not be new baseband for our device)... I have found the way to flash the baseband in recovery, so from this moment our phone can be completely modded using only recovery mode
First of all I have to say thank you to @alireza7991 and @broodplank1337 because they were the first one to think it could be possible in this way. I have to say thank you to @Rhonin86 for testing help (he has a spare i9001 ) and to @adfree because he posted this http://forum.xda-developers.com/showpost.php?p=52944982&postcount=29
Here is a list of zip files containing basebands, I will update it from time to time
I9001XXKPO (last Italian and German stock firmware no brand)
I9001BUKP7 (last Italian and German stock Vodafone firmware
me and @Rhonin86 tested this only on the last ADC TWRP 2.7.0.0, but should work on custom recoveries
Thanks to: @alireza7991 and @broodplank1337 for the concept @Rhonin86 for testing @adfree for the partition layout and name
Click to expand...
Click to collapse
Thank you for your work.
I guess XXKPO is the newest one (it's the baseband I'm using right now)
In your personal experience which one is best for signal specially GPS usage?
Regards,
Emilio
ecastel said:
Thank you for your work.
I guess XXKPO is the newest one (it's the baseband I'm using right now)
In your personal experience which one is best for signal specially GPS usage?
Regards,
Emilio
Click to expand...
Click to collapse
i used the two uploaded ones and i think they are quite the same, i stucked with bukp7 because is the last i tried and being quite the same as kpo i did not want to use odin to change it, now i will gather some basebands and make flashable zips, so who wants can try easily
im using the KPO baseband , yesterday i flashed release 6 of the ADC's cyanogen team , i love it !!! fast & smooth with ZERO bugs, then i flashed the KPO baseband ...i dont know but i feel much more battery life ...due to the baseband or the new rom & kernet ???
Rom: AriesVE DevConnection Team CM 11.0 [ION+PMEM ADSP]
Kernel: K^Kernel 3.4.x OC/EXUV 366MB [ION+PMEM ADSP]
Recovery: Team Win Recovery Project v2.7.0
Baseband: XXKPO
Governor: smatassV2
I/O Scheduler: SIO
CPU Frequencies: 196 - 1665 MHz
Looks good! I'm now on KPM baseband (general Europe), because I'm from the Netherlands. Curious if the KPO baseband works in the Netherlands too!:laugh:
Edit: connection with provider established! Let's see what it's going to do over time!
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Thanks for your work.
It could be great if you made a zip for backup current baseband too.
alireza7991 said:
Thanks for your work.
It could be great if you made a zip for backup current baseband too.
Click to expand...
Click to collapse
why not?
Edit: added to the second post script for backup/restore, and disclaimer added... just in case
Thank you !
Cool! What's your experience, do you need to wipe caches after flashing the baseband?
t5s said:
Cool! What's your experience, do you need to wipe caches after flashing the baseband?
Click to expand...
Click to collapse
no, baseband is a independent from os, it is in another partition, it talks with OS using RIL
ktulu84 said:
no, baseband is a independent from os, it is in another partition, it talks with OS using RIL
Click to expand...
Click to collapse
Ok, because I had it once upon a time with a stock gingerbread rom that it had issues after flashing a new baseband via odin and it stabilized after wiping caches. But maybe it was coincidence.
Im using XXKPO for almost 2 years now, and never had any problems with it. The batterylife is great and i also have signal everywhere (provider: o² Germany)
Gesendet von meinem GT-I9001 mit Tapatalk 2
[Edit] Problem solved. You can ignore the following post. The camera is working with the XXKPO baseband!
----------
hello guys,
i flashed XXKPO in recovery. Since then my camera (aosp & google) can't safe photos anymore. The pictures are taken but not saved. It worked with XXKPK before,
I am using CM11-20140808-UNOFFICIAL-dev_connection_team_arievse
Things i tried:
1. factory reset
2. download baseband zip a second time, flash the new file
3. installing CM rom image again
Non of these efforts made a change.
I was thinking about formatting the internal sd-card, but i haven't done this yet, because i have no difficulties to write on this partition.
Does anyone have an idea, what caused this strange behavior?
Just wanted to know what will happen if I flash baseband/firware on custom rom? I mean from sammobile. Thanks
a4apple said:
Just wanted to know what will happen if I flash baseband/firware on custom rom? I mean from sammobile. Thanks
Click to expand...
Click to collapse
Will install the stock ROM
Hugo-PT said:
Will install the stock ROM
Click to expand...
Click to collapse
Eh? Which mean if now i have custom rom and custom recovery, it will revert back to stock rom? and all my data storage will gone, like a new phone?
a4apple said:
Eh? Which mean if now i have custom rom and custom recovery, it will revert back to stock rom? and all my data storage will gone, like a new phone?
Click to expand...
Click to collapse
Yep!
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
CM12.1 is here for the D800, aka the AT&T LG G2.
This is a source build rom, which includes all the latest changes from cm. The nightlies are starting August 2nd.
Instructions
Official support is now limited to Kitkat and Lollipop basebands. CM-12.1 is based on a completely new kernel. This has enabled support for the latest basebands newer than jellybean.
While many people and devices are in various states we officially recommend flashing back to stock then fully updating your device before using cm-12.1.
If you are coming straight from cm-12.0 the rom will not boot.
Download cm-12.1, and gapps. Put them on your sdcard, reboot to recovery. Flash, and enjoy!
The latest will be available at:
http://get.cm/?device=d800
Gapps:
Official CM ones (soon):
http://wiki.cyanogenmod.org/w/Google_Apps
Click to expand...
Click to collapse
Known Issue
None!
Click to expand...
Click to collapse
Change Log
Click to expand...
Click to collapse
Special Thanks To!
None of this would be possible without the following people:
rashed
acree
Click to expand...
Click to collapse
Source
http://github.com/CyanogenMod
Click to expand...
Click to collapse
Hooray! And good stuff.
Thanks for all the work on this!
Also, might be worth mentioning the need for the LP bootstack
Edit: Adding link to the LG-Devs bootstacks. You'll probably want the D800 bumped version, though the loki one should work as well.
https://github.com/lg-devs/bootstacks/tree/master/d800/lp
You'll have to click on the file, then click the "Raw" button to start the download.
Are you saying it's best to flash back to stock as in "LGD800AT-01-V10o-310-410-OCT-19-2013+0.tot" , and then root, recovery, flash, etc? (just to be clear).
faheyd said:
Are you saying it's best to flash back to stock as in "LGD800AT-01-V10o-310-410-OCT-19-2013+0.tot" , and then root, recovery, flash, etc? (just to be clear).
Click to expand...
Click to collapse
Flash back then apply all stock updates, so you are on stock lollipop. After that root, and install cm. This will provide the best experience and is the only method that bug reports will be accepted from.
That said there are other situations your phone can be in and cm-12.1 work. Coming straight from cm-12.0 however will result in an assert check failing or a bootloop of the kernel not booting. We've broken compatibility, but its needed. There was no way to provide a proper experience and allow people to be on original jellybean firmware.
I'm good on flashing the tot, but 'Stock Updates', I have no idea where they would be nor how to get them. Do you have a link? Thanks for putting up with a noob, it's just I want clarification. Thanks. (I'm asking, because I'm sure others want to know also).
Flashing Blastagator's modem and bootloader inside TWRP then installing CM12.1 won't work?
praetorzero said:
Flashing Blastagator's modem and bootloader inside TWRP then installing CM12.1 won't work?
Click to expand...
Click to collapse
Like I said there is more than one way to get it to work but the only official way is to tot back to stock and make sure you are updated to lollipop.
Sent from my LG-ls990 using XDA Free mobile app
Shelnutt2 said:
Like I said there is more than one way to get it to work but the only official way is to tot back to stock and make sure you are updated to lollipop.
Sent from my LG-ls990 using XDA Free mobile app
Click to expand...
Click to collapse
These are the only tots, and I have no idea where to find 'updates', that I could find, which one, 20c?
http://forum.xda-developers.com/showthread.php?t=2663369
Noobs like me are going to need some clear cut instructions, not just some 'updates' thing.
The first nightly build of cm12.1 for d800 is online!!
Enviado desde mi LG-D800 mediante Tapatalk
Shelnutt2 said:
Flash back then apply all stock updates, so you are on stock lollipop. After that root, and install cm. This will provide the best experience and is the only method that bug reports will be accepted from.
That said there are other situations your phone can be in and cm-12.1 work. Coming straight from cm-12.0 however will result in an assert check failing or a bootloop of the kernel not booting. We've broken compatibility, but its needed. There was no way to provide a proper experience and allow people to be on original jellybean firmware.
Click to expand...
Click to collapse
"...so you are on stock lollipop." What stock lollipop are you talking about, where can I get that stock lollipop?
praetorzero said:
Flashing Blastagator's modem and bootloader inside TWRP then installing CM12.1 won't work?
Click to expand...
Click to collapse
blastagator's bump'd LP bootstack zip should get you past the assert on the value of TZ. However you'll also want the LP radio at the least. This may not be the most supported, but it'll probably get things working for you.
While it may not be officially supported, I at least got it working for me.
Backed up everything under /sdcard (adb pull /sdcard/ . )
Backed everything up in TWRP. (saved to USB, included Boot, System, Data, Cache, EFS, modem, Recovery, and Sensors)
Performed a factory wipe
Flashed bootstack-d800-LP_30f-bump-v1.1-blastagator-signed.zip
Flashed d800-30f-modem-blastagator-signed.zip
Flashed cm-12.1-20150804-NIGHTLY-d800.zip
Flashed open_gapps-arm-5.1-stock-20150804.zip
Flashed UPDATE-SuperSU-v2.46.zip
Backed everything up in TWRP (again) to have a clean CM12.1 base to start from. Included the same options as before (everything)
It worked for me, YMMV.
Please could you provide some feedback on camera and audio in whatsapp message? Thanks.
Enviado desde mi LG-D800 mediante Tapatalk
Camera's broken by an errant patch, should be working hopefully in another nightly or two.
praetorzero said:
While it may not be officially supported, I at least got it working for me.
Backed up everything under /sdcard (adb pull /sdcard/ . )
Backed everything up in TWRP. (saved to USB, included Boot, System, Data, Cache, EFS, modem, Recovery, and Sensors)
Performed a factory wipe
Flashed bootstack-d800-LP_30f-bump-v1.1-blastagator-signed.zip
Flashed d800-30f-modem-blastagator-signed.zip
Flashed cm-12.1-20150804-NIGHTLY-d800.zip
Flashed open_gapps-arm-5.1-stock-20150804.zip
Flashed UPDATE-SuperSU-v2.46.zip
Backed everything up in TWRP (again) to have a clean CM12.1 base to start from. Included the same options as before (everything)
It worked for me, YMMV.
Click to expand...
Click to collapse
At least we didn't have to wait for a dev to show how to do it. Good job.
Camera and flashlight working on tonight's nightly for me.
Sent from my LG-D800 using Tapatalk
ukguy115 said:
Camera and flashlight working on tonight's nightly for me.
Sent from my LG-D800 using Tapatalk
Click to expand...
Click to collapse
What about the time to open and the pic quality? Are ok? Whastapp audio message works? Thkx
Enviado desde mi LG-D800 mediante Tapatalk
luchardi said:
What about the time to open and the pic quality? Are ok? Whastapp audio message works? Thkx
Enviado desde mi LG-D800 mediante Tapatalk
Click to expand...
Click to collapse
Camera opens and takes pics. Speed and use will be subjective, its good enough for me but I am not a photography. I can say it is functional now though for me.
Sent from my LG-D800 using Tapatalk
Anyone figured out a way to remove the superuser hash mark from the status bar?
Never mind, I flashed SuperSU and it took care of it.
Before I go too much further down the rabbit hole, has anyone else had issues with voice calls? I cannot be heard unless I am on speakerphone or hold the bottom of the phone perpendicular to my mouth and speak directly into the bottom of my phone. Using a VOIP app (ie Hangouts) to make a call appears to work just fine.
I've tried switching persist.audio.dualmic.config from endfire to disable and back again with no benefit.
---------- Post added at 06:31 PM ---------- Previous post was at 06:26 PM ----------
Shelnutt2 said:
Flash back then apply all stock updates, so you are on stock lollipop. After that root, and install cm. This will provide the best experience and is the only method that bug reports will be accepted from.
Click to expand...
Click to collapse
Are we talking flashing the Kitkat TOT then taking the OTA upgrades to Jellybean? I ask because I've yet to find a TOT for Jellybean for the D800.
Hi! This is my first post, i want to share the Stock Nougat 7.0 Original firmware for XT1572/XT1575 from LATAM, i work with MotoService and found it yesterday after update the program (with date 7 Sept.)
Tested in my XT1575, no bugs, wifi, BT, signal OK.
I came from TruPureXMM 6.0, dont know if you have to come from stock 6.0 or can flash from AOSP, etc.
-- Screenshot:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
--------------------------------------------------------------------------------------------------------------
**INSTALLATION** [Don't try with LOCKED bootloader]
1. Put in fastboot mode
2. Run 0Flash.bat and wait until reboot
3. You might have to flash a modem that works in your country, if you are out of signal or no service you need a different modem (stock version its from latam/argentina)
Hit Thanks if it served you! Enjoy!
Links in comments
Firmware [updated 11-17]
https://mega.nz/#!p8BxnYDA!gXkTh258v5ENKwiu3jchplJNalA3D9KSRaorfgKly1I
well... i might as well try it...
wazaa08 said:
Firmware
https://mega.nz/#!YtR1FZjb!9NoBfIGBj8gQPAWD26DNZozrGIYMC74QWumBS78Dy0w"]https://mega.nz/#!YtR1FZjb!9NoBfIGBj8gQPAWD26DNZozrGIYMC74QWumBS78Dy0w
Modem XT1575
https://mega.nz/#!B8hVRLrS!kBTje3OmlpLCq2N8B--6YiUCVDwtbHGQRPoV0WWsFnU"]https://mega.nz/#!B8hVRLrS!kBTje3OmlpLCq2N8B--6YiUCVDwtbHGQRPoV0WWsFnU
Click to expand...
Click to collapse
What is the password?
edit
farvizu76 said:
What is the password?
Click to expand...
Click to collapse
Links corrected
Gracias!
Downloading... Muchas gracias por el aporte!
wazaa08 said:
Hi! This is my first post, i want to share the Stock Nougat 7.0 Original firmware for XT1572/XT1575 from LATAM, i work with MotoService and found it yesterday after update the program (with date 7 Sept.)
Tested in my XT1575, no bugs, wifi, BT, signal OK.
1. Put in fastboot mode
2. Run 0Flash.bat and wait until reboot
3. (XT1575 ONLY) flash 6.0 modem
Hit Thanks if it served you! Enjoy!
Links in comments
Click to expand...
Click to collapse
You forgot add:
Point 3. is impossible after 2. with locked bootloader.
For all, read before flashing:
https://forum.xda-developers.com/moto-x-style/help/unbrick-moto-x-pure-t3672108
Any chance you can upload the OTA August patch ?
Thanks for this ROM! I have a XT1575 Moto X Pure & I was able to install this ROM.
Only issue I've run into is I'm stuck on 3G after flashing the 6.0 modem, but at least I've got signal & data.
I also left my bootloader unlocked, you know, just in case?
I would like 4G LTE back though...
farvizu76 said:
What is the password?
Click to expand...
Click to collapse
dzidexx said:
You forgot add:
Point 3. is impossible after 2. with locked bootloader.
For all, read before flashing:
https://forum.xda-developers.com/moto-x-style/help/unbrick-moto-x-pure-t3672108
Click to expand...
Click to collapse
The modem is flasheable trough fastboot the same way the firmware, dont need unlocked bootloader.
(I could have uploaded the version with the xt1575 modem but I had to upload it all 2 times)
seven5three said:
Thanks for this ROM! I have a XT1575 Moto X Pure & I was able to install this ROM.
Only issue I've run into is I'm stuck on 3G after flashing the 6.0 modem, but at least I've got signal & data.
I also left my bootloader unlocked, you know, just in case?
I would like 4G LTE back though...
Click to expand...
Click to collapse
I have 4g normally in Argentina, try to flash the XT1575 modem from your region (US?)
Download the firmware from your region in pure fw & stuff post here, extract and replace the 3 files of my modem download (NON-HLOS.bin, BTFM.bin , fsg.mbn) and flash it via fastboot
So if this is for the 1575, can I use it in the USA and switch the language to English?
Realize if you use this on a XT1575 in the US, any future OTA's will fail... the modem's won't match the check.
Honestly, I wouldn't recommend this on anything but a Latin America device.
Thanks.
I flashed the Firmware over Lineage 14.1 as strangle this OS has problems with displaying names of incoming calls from Argentine Cellphone. Pecause of the "9" in my Phonebook it did not recognized local incoming calls from cellphone as they appear without the "9". Marshmallow Stock hadnt that problem.
Anyway..so far anything went smooth, but it seams my bootloader is locked now. I see that in the developer option the function
"Unlock OEM" is grayed out but the switch is in the ON position, which shoud indicate the it is unlocked.
How can i check that, as i want to flash custom recovery later.
Thomas_BA said:
Thanks.
I flashed the Firmware over Lineage 14.1 as strangle this OS has problems with displaying names of incoming calls from Argentine Cellphone. Pecause of the "9" in my Phonebook it did not recognized local incoming calls from cellphone as they appear without the "9". Marshmallow Stock hadnt that problem.
Anyway..so far anything went smooth, but it seams my bootloader is locked now. I see that in the developer option the function
"Unlock OEM" is grayed out but the switch is in the ON position, which shoud indicate the it is unlocked.
How can i check that, as i want to flash custom recovery later.
Click to expand...
Click to collapse
Boot into the bootloader, it is displayed right on the screen.
wazaa08 said:
Hi! This is my first post, i want to share the Stock Nougat 7.0 Original firmware for XT1572/XT1575 from LATAM, i work with MotoService and found it yesterday after update the program (with date 7 Sept.)
Click to expand...
Click to collapse
Wonderful! Been waiting for the full firmware package, to avoid the whole process of flashing 6.0 first, applying OTA etc. Thanks!
One question: is it dual-sim compatible? Here in Brazil the firmware is LATAM-DS. Can I flash this one you shared including its original 7.0 modem?
Hi have a XT1575 and i live en Panama can you help me, i don't know how update
wazaa08 said:
Hi! This is my first post, i want to share the Stock Nougat 7.0 Original firmware for XT1572/XT1575 from LATAM, i work with MotoService and found it yesterday after update the program (with date 7 Sept.)
Tested in my XT1575, no bugs, wifi, BT, signal OK.
I came from TruPureXMM 6.0, dont know if you have to come from stock 6.0 or can flash from AOSP, etc.
-- Screenshot:
--------------------------------------------------------------------------------------------------------------
**INSTALLATION** [Don't try with LOCKED bootloader]
1. Put in fastboot mode
2. Run 0Flash.bat and wait until reboot
3. (XT1575 ONLY) flash 6.0 modem (it works in Argentina, you will need a different one for another region)
Hit Thanks if it served you! Enjoy!
Links in comments
Click to expand...
Click to collapse
slicetwo said:
So if this is for the 1575, can I use it in the USA and switch the language to English?
Click to expand...
Click to collapse
This firm is for XT1572, you will need to flash an US modem after flash the firmware.
I will update the post with a US modem too later