Database Info

[Q] Bricked S3, can't flash PIT

When I boot the S3, it goes into download mode.
I tried flashing the VRALEC file, except it says no PIT paritions. So, I downloaded the PIT file for the 16GB phone, but I get the following error:
Code:
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004>
<ID:0/004> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
How can I fix this?

[HELP]softbricked my phone trying to root it

i tried to root my s6, now only shows the blue update error, how do i unbrick it ?
this is the odin log
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Can't open the specified file. (Line: 2012)
<OSM> All threads completed. (succeed 0 / failed 1)
Thanks alot

Galaxy S6 (SM-G920F) BRICKED. Please help.

Hello,
i have an issue with my Galaxy S6 (SM-G920F UK VOD) i believe it to be bricked, and not soft bricked. i can't get the phone to boot no matter what i try.
It all started after i had rooted the device, the root was successful and worked a treat until i decided i would like to play about with twrp. now i can't locate E/ and there does not seem to be any contents inside of the system folder.
Any help would be greatly appreciated and sorry if i have left out any important info.
I don't know if this is important but i have a recovery log.
pastebin com /PKE5fzgJ
trying to flash stock firmware using odin v3.10
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)

used the sampwned snapdragon

I'm not sure if i just retarded or not. but i used this guide.
https://forum.xda-developers.com/ga...root-g955u-g955u1-snapdragon-sampwnd-t3658911
and my phone is currently BQK5, G955U, and every time i try to run the flash i get
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> abl.elf
<ID:0/005> FAIL! (Auth)
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
ive tried doing one file at a time but then i get a boot img fail because im not using the BL and the others just give model mismatch so my bad maybe? idk
i cant figure out whats going on. need some help on this one.

Note 10 Plus - Odin error

hey,
I have a problem with my Note 10 plus, i tried to install another firmware ( because i installed busybox and after i had bootloop); now an error shows on the screen " an error has occurred while updating the device software...." i understand that this is download mod ( i cant access download mod or recovery now).
The problem is that when i try to install the firmware with odin it starts but after a while fails, like down below:
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1301)..
<ID:0/005> File analysis..
<ID:0/005> Total Binary size: 8172 M
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> NAND Write Start!!
<ID:0/005> SingleDownload.
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> dt.img
<ID:0/005> dtbo.img
<ID:0/005> system.img
<ID:0/005> __XmitData_Write
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
<ID:0/005> Added!!
What could i do?

Solved, set just the pit file with nand erese and repartition checked.