Database Info

[Solved] Miro Soft Bricked???

hi
I have a xperia miro which has been out cold since the last month...it just switched of one day and wont turn back on...wen i try to charge i geta solid green led.when i press power button i get 3 red led beeps. i can get into fastboot mode but for only few seconds,,after that again green led...
any ideas will be appreciated..

neo45215 said:
hi
I have a xperia miro which has been out cold since the last month...it just switched of one day and wont turn back on...wen i try to charge i geta solid green led.when i press power button i get 3 red led beeps. i can get into fastboot mode but for only few seconds,,after that again green led...
any ideas will be appreciated..
Click to expand...
Click to collapse
hope it might help....http://forum.xda-developers.com/showthread.php?t=1849170

kingviking said:
hope it might help....http://forum.xda-developers.com/showthread.php?t=1849170
Click to expand...
Click to collapse
thanks for that...solved it btw....apparently the phone doesnt charge in flash mode...i flashed stock kernel with bin4ary's flasher...then kept the phone attached to the computer,(altho all the guides ask u to connect to wall charger,mine just went into flash mode in wall charger)...this triggerd a set of loops on the phone between flash mode and kernel charging mode(the sony logo)....after about 3 hours i flashed th system using flashtool...and altho it got stuck at around 25%..i waited for an hour and then disconnected and reconnected to usb and voila!!!..it booted back in android ...now i am not sure if it was flashed correctly or not but my phone is working properly....
so last thoughts...remember those guidelines that ask u to have full battery for any process on your phone?....well they are not joking:angel:..

[Q] Help phone is not turning on red flashes

Hi my sony xperia E c1505 is not turning on it flashes red when hold power button it is not dead of battery fully charged left over night I unlocked the bootloader then i tried flashing it it says please turn on your phone and enable USB-debugging mode my phone can not turn on cause im in the bootloader after that I did somthing else but now i press power button just flashes red lights i am able to get in to flash mode and fastboot however i try flashing it but its says please enable USB-debugging is there a way to fix this and by the way im using flash tool and i have tried to update it with sony xperia update tool.

callum123457 said:
Hi my sony xperia E c1505 is not turning on it flashes red when hold power button it is not dead of battery fully charged left over night I unlocked the bootloader then i tried flashing it it says please turn on your phone and enable USB-debugging mode my phone can not turn on cause im in the bootloader after that I did somthing else but now i press power button just flashes red lights i am able to get in to flash mode and fastboot however i try flashing it but its says please enable USB-debugging is there a way to fix this and by the way im using flash tool and i have tried to update it with sony xperia update tool.
Click to expand...
Click to collapse
when you connect your phone in flashmode green light should stay on (press & hold vol down then plug usb in)
it should show
"device connected in flashmode"
IF you want fastboot mode
when you connect your phone in fastboot mode blue light should stay on (press & hold vol up then plug usb in)
NOTE-it should actually do bootloops....not sure why red light

callum123457 said:
Hi my sony xperia E c1505 is not turning on it flashes red when hold power button it is not dead of battery fully charged left over night I unlocked the bootloader then i tried flashing it it says please turn on your phone and enable USB-debugging mode my phone can not turn on cause im in the bootloader after that I did somthing else but now i press power button just flashes red lights i am able to get in to flash mode and fastboot however i try flashing it but its says please enable USB-debugging is there a way to fix this and by the way im using flash tool and i have tried to update it with sony xperia update tool.
Click to expand...
Click to collapse
Sometimes flash tool, while flashing tells me to turn on usb debugging (although its already on). So what do I do? Wait. After ten minutes(approx), device disconnects automatically and then flashtool requests me to connect in flash mode. So I disconect my usb cable and connect it again in flash mode and voila! flash begins. Worked for me, hope it works for u too..
Sent from my Xperia E dual using XDA Premium 4 mobile app

sohailferdous said:
Sometimes flash tool, while flashing tells me to turn on usb debugging (although its already on). So what do I do? Wait. After ten minutes(approx), device disconnects automatically and then flashtool requests me to connect in flash mode. So I disconect my usb cable and connect it again in flash mode and voila! flash begins. Worked for me, hope it works for u too..
Sent from my Xperia E dual using XDA Premium 4 mobile app
Click to expand...
Click to collapse
yes thats a common mistake
on flashmode connect phone in flashmode only when asked (or like you said ...you will have to do twice)
on fastboot mode your phone has to be connected in fastboot before selecting the fastboot mode

I'm having very similar trouble, i flashed FXP CM10 a little while ago until the phone stopped receiving a signal (which has happened a few times using CM10), unfortunately the battery died before i got home to flash it again. 3 days and 7 hours later and the battery still hasn't charged, i've managed to boot into android very quickly while it's connected to a wall charger but i get nothing at all if i try and connect in flashmode or fastboot.
Is the battery dead? Is there something i'm probably missing? I figured this might go to someway with hoping the OP.
[Edit: Good news! I've plugged into USB and i can get to the battery bar with the power symbol, maybe i can get to flashmode after all!]
[Edit 2:] Noticing the phone had just enough power to get to the battery/power symbol screen, held down the volume button for about a minute till it went through that cycle and managed to get it into flashmode, installed stock and plugged it into the wall. 5 mins later i hit the power button and it's working again! Hooray!

GeoH85 said:
I'm having very similar trouble, i flashed FXP CM10 a little while ago until the phone stopped receiving a signal (which has happened a few times using CM10), unfortunately the battery died before i got home to flash it again. 3 days and 7 hours later and the battery still hasn't charged, i've managed to boot into android very quickly while it's connected to a wall charger but i get nothing at all if i try and connect in flashmode or fastboot.
Is the battery dead? Is there something i'm probably missing? I figured this might go to someway with hoping the OP.
[Edit: Good news! I've plugged into USB and i can get to the battery bar with the power symbol, maybe i can get to flashmode after all!]
[Edit 2:] Noticing the phone had just enough power to get to the battery/power symbol screen, held down the volume button for about a minute till it went through that cycle and managed to get it into flashmode, installed stock and plugged it into the wall. 5 mins later i hit the power button and it's working again! Hooray!
Click to expand...
Click to collapse
use jim34 cm10 with hsr0 kernel....FXP IS CRAP for daily use

don't connect your phone to the pc until flashtool asks you to. I get that thing sometimes when I reflash a rom or kernel
Sent from my ST21i using Tapatalk

Miro bricked after flashing wrong bootloader

Hi,
I don't know what can I do now, perhaps noting. I accidentialy flashed wrong bootloader (from other xperia, not Miro). Now phone seems to be completly bricked, I can't turn it on and my PC does not see any new device after connecting phone to usb. I also tried to remove and insert battery, after this when trying to power on, there is short vibration and nothing more.
Do you have any ideas? Or I simply should to use it as brick, not as phone or put it to my toilet and wash? Thanks.

Can you get in flashmode? Power button down + connect to pc. Flash proper ftf for your phone.
Sent from Xperia M2 D2303

Don't worry, Your phone is not hard bricked. As you mentioned that on starting , phone is vibrating that means there are chances to recover your phone.
1.First go through this guide :Using Flashtool for Xperia devices
2.Download your current stock firmware . Visit this: Miro all official firmwares
3.Install proper drivers as mentioned in the above 1.flashtool guide.
4.Flash the firmware for your phone , according to the above 1. Flastool guide.
5.Wait untill flashing completes. start your device when you are told to do so.
Good luck :good:

Dzepar said:
Can you get in flashmode? Power button down + connect to pc. Flash proper ftf for your phone.
Sent from Xperia M2 D2303
Click to expand...
Click to collapse
It seems I can't. I already tried this, but nothing happens. As far as I know, there should be blue led after connect. But nothing happens and PC can't see any new device.

giaur said:
It seems I can't. I already tried this, but nothing happens. As far as I know, there should be blue led after connect. But nothing happens and PC can't see any new device.
Click to expand...
Click to collapse
You should see green light. Try this :
Pull out battery, hold power button for 10 seconds without battery. Reinstall battery, hold volume button - and connect to usb. Then follow steps that prateek.invasion gave you.
The point is you can flash ftf and restore your phone.
Good luck.
Sent from Xperia M2 D2303

Thanks, I will try. Batteery is not charging, so I need to do this quick, it was not fully charged.

Unfortunatly, I can't do anything. I tried to connect while Volume down + power pressed. But nothing happens, only led flashing with red color. PC can't see any new device after I connect to usb.
Any ideas?

giaur said:
Unfortunatly, I can't do anything. I tried to connect while Volume down + power pressed. But nothing happens, only led flashing with red color. PC can't see any new device after I connect to usb.
Any ideas?
Click to expand...
Click to collapse
I had the same issue with my xperia e after I unlocked the bootloader and installed CWM, the phone just rebooted itself at boot up. If you have installed CWM I suggest you to install a custom rom and a new kernel. That worked for me . Or ofc, if you have warranty you can send it to them. They won't be able to tell if you installed another rom since the pc doesn't recognize the phone.

I don't have cwm... trying to connect to computer with volume down pressed. After this led starts flashing red and computer can't see any device connected
Seems there is no any recovery or I can't put it to recovery mode.

Problems with my d6633 Z3 Dual

Hallo people,
I have a very big problem with my d6633. I installed tonight TWRP - so fas, so good. After installing TWRP asked me to root the device, I said YES. My bootloader was unlocked. Then I couldn't exit TWRP. After every reboot the device started into TWRP. Now I can not start the device. I tried with Power+ Volume+, reset button - nothing.
Any suggestions?
Thanks for your help.

mazagi said:
Hallo people,
I have a very big problem with my d6633. I installed tonight TWRP - so fas, so good. After installing TWRP asked me to root the device, I said YES. My bootloader was unlocked. Then I couldn't exit TWRP. After every reboot the device started into TWRP. Now I can not start the device. I tried with Power+ Volume+, reset button - nothing.
Any suggestions?
Thanks for your help.
Click to expand...
Click to collapse
Use flashtool go back stock, after flash twrp, flash supersu manually, don't let twrp install for you

yuzhengwen said:
Use flashtool go back stock, after flash twrp, flash supersu manually, don't let twrp install for you
Click to expand...
Click to collapse
How can I do that? There is no power on my device. And I think I cannot charge it...

mazagi said:
How can I do that? There is no power on my device. And I think I cannot charge it...
Click to expand...
Click to collapse
Google using flashtool to flash stock firmware

yuzhengwen said:
Google using flashtool to flash stock firmware
Click to expand...
Click to collapse
No chance. The device will not be detected. I can not charge it.

mazagi said:
No chance. The device will not be detected. I can not charge it.
Click to expand...
Click to collapse
How much % did it have before you started the procedure?
Did you try holding down vol+ and then plugging it into USB?

Hello Jkay7,
Thanks for your support. My solution was to leave the device switched off over the night. Connected via original cable. Today in the morning my dyouzhengwen evice was detected via flash tool and as youzhengwen suggested I could flash the original ftf file.

artusk01 said:
Hello Jkay7,
Thanks for your support. My solution was to leave the device switched off over the night. Connected via original cable. Today in the morning my dyouzhengwen evice was detected via flash tool and as youzhengwen suggested I could flash the original ftf file.
Click to expand...
Click to collapse
Nice to hear that!

Any help would be appreciated
Sony Xperia Z3 Dual D6633
I have tried just about every method seen. My problem with the flashtool or PC companion is that the phone is recognized by the computer but I can only start to turn the device on which I don't believe it actually boots. Broken display and new display does not power on.
Or it connects in fastboot by holding volume up when connecting. This shows a blue led.
But trying to connect in flash mode by holding power down just makes the led flash red then green continuously.
And for the pc companion it always says the connection was unsuccessful once the led turns green on the device.
I got the phone for only $40 in this condition. So I cannot say what entirely was wrong or what it's last working state was.
I bought a new screen and power flex cable. As well as a back plate and tempered glass protectors. I was going to wait until everything works perfect speakers and all before I sealed it tight with water proof adhesive stickers.
Even before I bought the new power flex the computer recognized it and the battery health and charge %. The battery was able to charge. But I couldn't turn the device on.
The computer confirmed that it had been at 29% after some time charging and then 100% after leaving it on charge.
Now with the new screen and power cable the phone still does nothing if not plugged it. The light was red at first, but then yellow, then after some time green when the battery fully charged. This was again even before the new parts.
I have to plug it in to try anything.
It goes red then starts to turn on and turns green.
But I hear no sound, get no vibrations, the computer only sees it as the phone and shows absolutely nothing on the removable disk. Just blank when I click on the drive volume. But it is seen as an Xperia D6633 phone or fastboot Android device.
I've tried the reset button, holding power and volume up, volume down, all three. Tried my factory cable. Different cables, different ports, uninstalling it from service manager and letting the flash tool recognize and install it.
I also tried the new display on the old power flex and the old display on the new power flex.
Nothing changed, no vibrations, no sounds, system never actually fully starts as far as I can tell, and cannot connect in flash mode only fast boot. And the flashable file is only seen in flash mode. Fastboot can only see the folder but it is ready to flash files as far as I can tell.

@xdathekilljoy
That's a lot of money you're putting into an (apparently) broken phone Brave!
Okay so what happens if you hold Vol+ while it's shut down and then connect it to USB, the LED turns blue, right?
So why does flashing it from there on not work?

Jkay7 said:
@xdathekilljoy
That's a lot of money you're putting into an (apparently) broken phone Brave!
Okay so what happens if you hold Vol+ while it's shut down and then connect it to USB, the LED turns blue, right?
So why does flashing it from there on not work?
Click to expand...
Click to collapse
Well it didn't seem that broken at first and both it and the display were only about 37 piece. Power flex was almost 10. Seemed like a rightful price.
Yes the led turns blue and it is in fastboot mode. The flash file seems to only be readable for flashing in flash mode "volume down". I can see the folder of the flash file in fastboot mode " volume up ", but not in a flashable format.
And when connecting " volume down " it fails a connection while the led just flashes green to red to green to red continually

Two updates
1. I thought I should mention that when I do plug the phone in to a charger or computer the top does get a bit warm or hot as well as the led turns on. Different color depending.
2. With much fiddling and trying if holding the volume down button for different lengths of time while connecting up a computer I finally got it to connect in flash mode and flashed a file...... No change.
At this point maybe I should try a new battery for the hell of it even though this one seems to be working.
Or there is a minute hardware damage somewhere. Maybe the power ic? Or s capacitor?

[help] Z3 Completely dead (no vibration / no led / no charging / no flash mode)

Hello everybody!
I recently wanted to use a custom rom..
So I Flashed the stock firmware the .291 build. after that I wanted to flash twrp recovery.
So I downgraded the kernel to ,575 then flashed the recovery file, and from the recovery I flashed the Existenz rom (.291 based).
Then I rebooted the device,, Unfortunately I got a boot loop on SONY logo.
So I reflashed the stock firmware (.291) throw flashtool. but flash didn't complete,,, and I got boot loop again.
after that I DON'T KNOW why I flashed the .575 kernel.. Flash completed,, phone turned off
then it's COMPLETELY DEAD.. no signs of life
I tried every power- volume combinations, but I got no vibrations nor leds. and the charging sign doesn't appear when connecting the device to a power supply.
I only hear the connection sound when I connect the device to the computer and press volume down + power button for 10 secs, but it shows nothing on computer!
Any help would be appreciated

Your best bet if it shows no sign of life is to charge for a few hours to make sure it has enough battery.
Hopefully the red light comes on at some point. Either way try leaving it plugged in for a few hours.
Then you can try flashing again.
Ensure all the drivers are properly installed for flashtool.
Ensure you have the correct ftf for your device!
Start flash mode for a full .291 ftf and plug the phone in while holding down the volume down button as normal.
Try this repeatedly until you get a connection.
Alternatively you can wrap a very tight rubber band around the volume down key and connect it while flashtool is in flashmode.
If you're lucky a connection will be made and flashtool will have time to flash the firmware.
Persistence is key here. Many times a brick can be saved but it can take a long time.
Good luck and I hope it works

keep it on charge overnight.flash again when led turns on