Related
Fix Xperia C Red Light brick
Are you facing that the red led on your device blinks and there is no other signs of life? Then you are in the correct thread, I faced this issue when flashing a corrupted recovery but then I found out a easy way to fix it without opening the device or sending it in to Sony.
Requirements:
Xperia C with red light softbrick
MicroUSB Cable
Sony Update Service
Click to expand...
Click to collapse
1. The first thing you need to do is to make sure that you have downloaded Sony Update Service and have installed it onto your PC from the link above, if not, do it now.
2. Now launch Sony Update Service and select Xperia C in the list and then press Next.
3. Hold the Volume Up button and plugin microusbcable while doing so, if that doesn't work for you, hold power + volume up and plugin the microusbcable while doing. Keep holding button combination for a few seconds and wait for a green light on your phone, if it appears check on
your PC so that it's detected.
4. Wait while the firmware is being downloaded and reinstalled on your phone and enjoy your working device!
Have tried this on my bricked xperia c red led
Few weeks back no success
Logic
If you flash wrong recovery there is no way to boot in any mode
I can say this with 100% confident as I had spent full 3 days and tried every thing...
If u wona check goto custome mod for xperia c thred and get recovery installed
Then try this and share results
All the best
chauhanjayc said:
Have tried this on my bricked xperia c red led
Few weeks back no success
Logic
If you flash wrong recovery there is no way to boot in any mode
I can say this with 100% confident as I had spent full 3 days and tried every thing...
If u wona check goto custome mod for xperia c thred and get recovery installed
Then try this and share results
All the best
Click to expand...
Click to collapse
I flashed a faulty recovery using mobileuncles and there was no signs of life other than a red led liggt, and holding power + volume up works just fine and it went into flashmode.
I have the same issue.
I organized xperia light rom for our xperia c, I flashed it from custom recovery. Phone is completely dead now.
There is a just red light, phone does not go into download or fastboot mode. Pc Companion, Sony Update Center, Wmshua Flashtool do not recognize the phone.
Any suggestion with that?
I don't have warranty, my last option is to pay money for technical service.
this worked for me but instead of POWER+VOL UP i used POWER+VOL DOWN
thanks
thank, i like this forum
worth to try... (hope it won't happen to me :laugh: )
I have experienced this too, however, instead of using the Sony Update Service, I used the Sony PC Companion. At first it was not working, so I did a hard reset on the phone (press the button at the back). I held the power+up button while inserting the cable, and finally it was detected by Sony. It will reset your device to factory settings though.
seiferfury said:
I have experienced this too, however, instead of using the Sony Update Service, I used the Sony PC Companion. At first it was not working, so I did a hard reset on the phone (press the button at the back). I held the power+up button while inserting the cable, and finally it was detected by Sony. It will reset your device to factory settings though.
Click to expand...
Click to collapse
How did it
How Catch 4 buttons simultaneously
Please reply to the importance of
Im in the same scenario.. I tried all the procedures here but i failed.. I noticed that when i connect it, it disconnects after a while along with blinking of led light then reconnect again. And my PC detects it as unknown device.. I tried to install ADB driver but it also fails. Please help me.. Thanks. Sorry about my English
zergmac023 said:
Im in the same scenario.. I tried all the procedures here but i failed.. I noticed that when i connect it, it disconnects after a while along with blinking of led light then reconnect again. And my PC detects it as unknown device.. I tried to install ADB driver but it also fails. Please help me.. Thanks. Sorry about my English
Click to expand...
Click to collapse
If you flash a different device's rom, it happens. If you replace your motherboard, it will work again.
(
TacoNikky said:
If you flash a different device's rom, it happens. If you replace your motherboard, it will work again.
Click to expand...
Click to collapse
Which probably crying::crying::crying:
yeubeo168 said:
Which probably crying::crying::crying:
Click to expand...
Click to collapse
I have bought motherboard from china http://www.yoybuy.com/en/show/37431065583/ from this seller.
It took 20 days to arrive to Turkey. I have changed my motherboard and my phone is back right now :victory:
It works like a charm. Model number changed, it shows s39h but phone works like old days :good:
A detailed guide :
http://forum.xda-developers.com/sony-xperia-c/general/how-to-install-restore-stock-android-t2832005
It worked!!!!!
GethPrime said:
Fix Xperia C Red Light brick
Are you facing that the red led on your device blinks and there is no other signs of life? Then you are in the correct thread, I faced this issue when flashing a corrupted recovery but then I found out a easy way to fix it without opening the device or sending it in to Sony.
Requirements:
1. The first thing you need to do is to make sure that you have downloaded Sony Update Service and have installed it onto your PC from the link above, if not, do it now.
2. Now launch Sony Update Service and select Xperia C in the list and then press Next.
3. Hold the Volume Up button and plugin microusbcable while doing so, if that doesn't work for you, hold power + volume up and plugin the microusbcable while doing. Keep holding button combination for a few seconds and wait for a green light on your phone, if it appears check on
your PC so that it's detected.
4. Wait while the firmware is being downloaded and reinstalled on your phone and enjoy your working device!
Click to expand...
Click to collapse
It worked for my Xperia M (rooted on JB 4.3) with a locked bootloader which was STUCK on bootloop screen and when I did the whole thing with holding the power and volume up button (after I let the battery die after so many bootloops it did), FINALLY I was able to take it to flashmode, while I had selected from Sony PC Companion to repair my phone, and after 3-4 tries, I DID IT!!! Thank you so much for this thread ( I DEFINITELY pressed the "thanks" button), it really SAVED ME time and money (because I was planning to send it to Sony to fix it and you ALL know how bastards Sony is)!!!! And to all those of you who are DESPERATE to fix their phone (I hope you read this thread), DON'T PANIC, and DON'T GIVE UP!!! It took me 2 days of searching the web, and FINALLY I MADE IT!!! There are ALWAYS solutions to these kinds of problems!!!!
red light
dear friends please help me. I wanted to install cwm recovery with mobile uncle tools. when I placed recovery.img to phone memory(not in any folder), it didn't find the file, but when in sd card(not in any folder) it succesfully find. I selected and flashed, but the phone shut down and didn't start anymore. yesterday, when plugging to charge the red light under the screen was blinking. but today, it just stays on, not blinking, but after some time, goes off again, and start blinking. when I connect to PC, first it connects, after some time connection is lost and green light passes to red again, after some time it again connects. I tried Sony Update Service and PC Companion, didn't work. Please help...
Need help
same here only red light is blinking,,,i tried doing Power+vol up and Power+vol down and by inserting cable also...it just show a red light when plugged in
i'm also having the same problem....somebody please help!!!!really need to use it
kamran.kerim said:
dear friends please help me. I wanted to install cwm recovery with mobile uncle tools. when I placed recovery.img to phone memory(not in any folder), it didn't find the file, but when in sd card(not in any folder) it succesfully find. I selected and flashed, but the phone shut down and didn't start anymore. yesterday, when plugging to charge the red light under the screen was blinking. but today, it just stays on, not blinking, but after some time, goes off again, and start blinking. when I connect to PC, first it connects, after some time connection is lost and green light passes to red again, after some time it again connects. I tried Sony Update Service and PC Companion, didn't work. Please help...
Click to expand...
Click to collapse
i'm also having the same problem....somebody please help!!!!really need to use it
chauhanjayc said:
Have tried this on my bricked xperia c red led
Few weeks back no success
Logic
If you flash wrong recovery there is no way to boot in any mode
I can say this with 100% confident as I had spent full 3 days and tried every thing...
If u wona check goto custome mod for xperia c thred and get recovery installed
Then try this and share results
All the best
Click to expand...
Click to collapse
Does that mean phone is dead?
choxx said:
Does that mean phone is dead?
Click to expand...
Click to collapse
no all you need stock kernel
you can either google it or download ftf and check all except kernel
done
Hi my sony xperia E c1505 is not turning on it flashes red when hold power button it is not dead of battery fully charged left over night I unlocked the bootloader then i tried flashing it it says please turn on your phone and enable USB-debugging mode my phone can not turn on cause im in the bootloader after that I did somthing else but now i press power button just flashes red lights i am able to get in to flash mode and fastboot however i try flashing it but its says please enable USB-debugging is there a way to fix this and by the way im using flash tool and i have tried to update it with sony xperia update tool.
callum123457 said:
Hi my sony xperia E c1505 is not turning on it flashes red when hold power button it is not dead of battery fully charged left over night I unlocked the bootloader then i tried flashing it it says please turn on your phone and enable USB-debugging mode my phone can not turn on cause im in the bootloader after that I did somthing else but now i press power button just flashes red lights i am able to get in to flash mode and fastboot however i try flashing it but its says please enable USB-debugging is there a way to fix this and by the way im using flash tool and i have tried to update it with sony xperia update tool.
Click to expand...
Click to collapse
when you connect your phone in flashmode green light should stay on (press & hold vol down then plug usb in)
it should show
"device connected in flashmode"
IF you want fastboot mode
when you connect your phone in fastboot mode blue light should stay on (press & hold vol up then plug usb in)
NOTE-it should actually do bootloops....not sure why red light
callum123457 said:
Hi my sony xperia E c1505 is not turning on it flashes red when hold power button it is not dead of battery fully charged left over night I unlocked the bootloader then i tried flashing it it says please turn on your phone and enable USB-debugging mode my phone can not turn on cause im in the bootloader after that I did somthing else but now i press power button just flashes red lights i am able to get in to flash mode and fastboot however i try flashing it but its says please enable USB-debugging is there a way to fix this and by the way im using flash tool and i have tried to update it with sony xperia update tool.
Click to expand...
Click to collapse
Sometimes flash tool, while flashing tells me to turn on usb debugging (although its already on). So what do I do? Wait. After ten minutes(approx), device disconnects automatically and then flashtool requests me to connect in flash mode. So I disconect my usb cable and connect it again in flash mode and voila! flash begins. Worked for me, hope it works for u too..
Sent from my Xperia E dual using XDA Premium 4 mobile app
sohailferdous said:
Sometimes flash tool, while flashing tells me to turn on usb debugging (although its already on). So what do I do? Wait. After ten minutes(approx), device disconnects automatically and then flashtool requests me to connect in flash mode. So I disconect my usb cable and connect it again in flash mode and voila! flash begins. Worked for me, hope it works for u too..
Sent from my Xperia E dual using XDA Premium 4 mobile app
Click to expand...
Click to collapse
yes thats a common mistake
on flashmode connect phone in flashmode only when asked (or like you said ...you will have to do twice)
on fastboot mode your phone has to be connected in fastboot before selecting the fastboot mode
I'm having very similar trouble, i flashed FXP CM10 a little while ago until the phone stopped receiving a signal (which has happened a few times using CM10), unfortunately the battery died before i got home to flash it again. 3 days and 7 hours later and the battery still hasn't charged, i've managed to boot into android very quickly while it's connected to a wall charger but i get nothing at all if i try and connect in flashmode or fastboot.
Is the battery dead? Is there something i'm probably missing? I figured this might go to someway with hoping the OP.
[Edit: Good news! I've plugged into USB and i can get to the battery bar with the power symbol, maybe i can get to flashmode after all!]
[Edit 2:] Noticing the phone had just enough power to get to the battery/power symbol screen, held down the volume button for about a minute till it went through that cycle and managed to get it into flashmode, installed stock and plugged it into the wall. 5 mins later i hit the power button and it's working again! Hooray!
GeoH85 said:
I'm having very similar trouble, i flashed FXP CM10 a little while ago until the phone stopped receiving a signal (which has happened a few times using CM10), unfortunately the battery died before i got home to flash it again. 3 days and 7 hours later and the battery still hasn't charged, i've managed to boot into android very quickly while it's connected to a wall charger but i get nothing at all if i try and connect in flashmode or fastboot.
Is the battery dead? Is there something i'm probably missing? I figured this might go to someway with hoping the OP.
[Edit: Good news! I've plugged into USB and i can get to the battery bar with the power symbol, maybe i can get to flashmode after all!]
[Edit 2:] Noticing the phone had just enough power to get to the battery/power symbol screen, held down the volume button for about a minute till it went through that cycle and managed to get it into flashmode, installed stock and plugged it into the wall. 5 mins later i hit the power button and it's working again! Hooray!
Click to expand...
Click to collapse
use jim34 cm10 with hsr0 kernel....FXP IS CRAP for daily use
don't connect your phone to the pc until flashtool asks you to. I get that thing sometimes when I reflash a rom or kernel
Sent from my ST21i using Tapatalk
Hello,
I cant seem to start my Xperia J back up. I get three blinking led lights when trying to turn the phone on. If I hook up to wall charger I get a solid green, if I hold Vol Up, I can get Solid Blue.
When I connect to PC, I can get into Fastboot and Flashmode. I tried reflashing to stock, no luck. I cant get the phone to boot, battery is too low.
ANy ideas?
Recharge you battery on some other phone (I keep wall chargers just in case).
Do you have drivers instaled? Does Flashtool give any error?
Sent from my ST26i
Dzepar said:
Recharge you battery on some other phone (I keep wall chargers just in case).
Do you have drivers instaled? Does Flashtool give any error?
Sent from my ST26i
Click to expand...
Click to collapse
Don't have another phone to recharge with I do have drivers installed and flashtools gives no errors.
I tried to charge the battery by cutting a usb cord and holding the black and red cable to + and -. Now I just get a blinking green light when attempting to power the phone on.
kommie27 said:
I tried to charge the battery by cutting a usb cord and holding the black and red cable to + and -. Now I just get a blinking green light when attempting to power the phone on.
Click to expand...
Click to collapse
What you try do do? Did you flash some rom?
You usuali need to flash stock kernel via Flashtool after flashing rom so the phone turn on.
When you posting problem tell:
- What was the phone state ( stock rom JB 4.1.2. workin battery 40%)
- I was flashing Rom, kernel etc
and whats you problem now.
Youll have beter chance to get help
Dzepar said:
What you try do do? Did you flash some rom?
You usuali need to flash stock kernel via Flashtool after flashing rom so the phone turn on.
When you posting problem tell:
- What was the phone state ( stock rom JB 4.1.2. workin battery 40%)
- I was flashing Rom, kernel etc
and whats you problem now.
Youll have beter chance to get help
Click to expand...
Click to collapse
Phone State was flashing from Cyanogen to Stock. I am trying to go back to Stock. Flashing stock ftf
I get a green light now only when hitting power.
kommie27 said:
Phone State was flashing from Cyanogen to Stock. I am trying to go back to Stock. Flashing stock ftf
I get a green light now only when hitting power.
Click to expand...
Click to collapse
Try this:
Open Flashtool, select ftf that you want to flash, wait till it tells to connect the phone, conect phone ( hold volume down and connect usb) wait till the process finish.
Good Luck.
Sent from my ST26i
Flash completes successfully. When I try to turn phoneon. Green Led blinks and nothing happens. If I connect to charger solid green.
No clue. Did your phone fall or something? It looks that you screen is broken.
Sent from my ST26i
I install custom rom to my xperia c when it low battery (around 20%) and after that my phone turn out to bricked. It look like a no battery phone right now and it only have red led when connect to pc or charger. I've tried everything they told ( power button, volume up,down, sus, perfect flash, flash tool, pc companion, reset button on the back, charged for long hours) but nothing work. Please help me!!!
Emotionless said:
I install custom rom to my xperia c when it low battery (around 20%) and after that my phone turn out to bricked. It look like a no battery phone right now and it only have red led when connect to pc or charger. I've tried everything they told ( power button, volume up,down, sus, perfect flash, flash tool, pc companion, reset button on the back, charged for long hours) but nothing work. Please help me!!!
Click to expand...
Click to collapse
This is an old way but works
http://forum.xda-developers.com/sony-xperia-c/general/how-to-install-restore-stock-android-t2832005
iSiddharth said:
This is an old way but works
http://forum.xda-developers.com/sony-xperia-c/general/how-to-install-restore-stock-android-t2832005
Click to expand...
Click to collapse
Thanks, but It didn't detects my phone and now i sent it to Sony center.
Emotionless said:
I install custom rom to my xperia c when it low battery (around 20%) and after that my phone turn out to bricked. It look like a no battery phone right now and it only have red led when connect to pc or charger. I've tried everything they told ( power button, volume up,down, sus, perfect flash, flash tool, pc companion, reset button on the back, charged for long hours) but nothing work. Please help me!!!
Click to expand...
Click to collapse
There is no other way buddy
you have to go to service centre for this
i had done the same thing with my xperia c
i was installing custom rom without unlocking bootloader and but custom rom was installed but after few seconds my phone switch's off and that is hard brick not a single button was working same thing that happens with you
the problem was that there was a issue in the hardware in the motherboard
and ultimately they changed my phone's motherboard which is a single solution left!
Hallo people,
I have a very big problem with my d6633. I installed tonight TWRP - so fas, so good. After installing TWRP asked me to root the device, I said YES. My bootloader was unlocked. Then I couldn't exit TWRP. After every reboot the device started into TWRP. Now I can not start the device. I tried with Power+ Volume+, reset button - nothing.
Any suggestions?
Thanks for your help.
mazagi said:
Hallo people,
I have a very big problem with my d6633. I installed tonight TWRP - so fas, so good. After installing TWRP asked me to root the device, I said YES. My bootloader was unlocked. Then I couldn't exit TWRP. After every reboot the device started into TWRP. Now I can not start the device. I tried with Power+ Volume+, reset button - nothing.
Any suggestions?
Thanks for your help.
Click to expand...
Click to collapse
Use flashtool go back stock, after flash twrp, flash supersu manually, don't let twrp install for you
yuzhengwen said:
Use flashtool go back stock, after flash twrp, flash supersu manually, don't let twrp install for you
Click to expand...
Click to collapse
How can I do that? There is no power on my device. And I think I cannot charge it...
mazagi said:
How can I do that? There is no power on my device. And I think I cannot charge it...
Click to expand...
Click to collapse
Google using flashtool to flash stock firmware
yuzhengwen said:
Google using flashtool to flash stock firmware
Click to expand...
Click to collapse
No chance. The device will not be detected. I can not charge it.
mazagi said:
No chance. The device will not be detected. I can not charge it.
Click to expand...
Click to collapse
How much % did it have before you started the procedure?
Did you try holding down vol+ and then plugging it into USB?
Hello Jkay7,
Thanks for your support. My solution was to leave the device switched off over the night. Connected via original cable. Today in the morning my dyouzhengwen evice was detected via flash tool and as youzhengwen suggested I could flash the original ftf file.
artusk01 said:
Hello Jkay7,
Thanks for your support. My solution was to leave the device switched off over the night. Connected via original cable. Today in the morning my dyouzhengwen evice was detected via flash tool and as youzhengwen suggested I could flash the original ftf file.
Click to expand...
Click to collapse
Nice to hear that!
Any help would be appreciated
Sony Xperia Z3 Dual D6633
I have tried just about every method seen. My problem with the flashtool or PC companion is that the phone is recognized by the computer but I can only start to turn the device on which I don't believe it actually boots. Broken display and new display does not power on.
Or it connects in fastboot by holding volume up when connecting. This shows a blue led.
But trying to connect in flash mode by holding power down just makes the led flash red then green continuously.
And for the pc companion it always says the connection was unsuccessful once the led turns green on the device.
I got the phone for only $40 in this condition. So I cannot say what entirely was wrong or what it's last working state was.
I bought a new screen and power flex cable. As well as a back plate and tempered glass protectors. I was going to wait until everything works perfect speakers and all before I sealed it tight with water proof adhesive stickers.
Even before I bought the new power flex the computer recognized it and the battery health and charge %. The battery was able to charge. But I couldn't turn the device on.
The computer confirmed that it had been at 29% after some time charging and then 100% after leaving it on charge.
Now with the new screen and power cable the phone still does nothing if not plugged it. The light was red at first, but then yellow, then after some time green when the battery fully charged. This was again even before the new parts.
I have to plug it in to try anything.
It goes red then starts to turn on and turns green.
But I hear no sound, get no vibrations, the computer only sees it as the phone and shows absolutely nothing on the removable disk. Just blank when I click on the drive volume. But it is seen as an Xperia D6633 phone or fastboot Android device.
I've tried the reset button, holding power and volume up, volume down, all three. Tried my factory cable. Different cables, different ports, uninstalling it from service manager and letting the flash tool recognize and install it.
I also tried the new display on the old power flex and the old display on the new power flex.
Nothing changed, no vibrations, no sounds, system never actually fully starts as far as I can tell, and cannot connect in flash mode only fast boot. And the flashable file is only seen in flash mode. Fastboot can only see the folder but it is ready to flash files as far as I can tell.
@xdathekilljoy
That's a lot of money you're putting into an (apparently) broken phone Brave!
Okay so what happens if you hold Vol+ while it's shut down and then connect it to USB, the LED turns blue, right?
So why does flashing it from there on not work?
Jkay7 said:
@xdathekilljoy
That's a lot of money you're putting into an (apparently) broken phone Brave!
Okay so what happens if you hold Vol+ while it's shut down and then connect it to USB, the LED turns blue, right?
So why does flashing it from there on not work?
Click to expand...
Click to collapse
Well it didn't seem that broken at first and both it and the display were only about 37 piece. Power flex was almost 10. Seemed like a rightful price.
Yes the led turns blue and it is in fastboot mode. The flash file seems to only be readable for flashing in flash mode "volume down". I can see the folder of the flash file in fastboot mode " volume up ", but not in a flashable format.
And when connecting " volume down " it fails a connection while the led just flashes green to red to green to red continually
Two updates
1. I thought I should mention that when I do plug the phone in to a charger or computer the top does get a bit warm or hot as well as the led turns on. Different color depending.
2. With much fiddling and trying if holding the volume down button for different lengths of time while connecting up a computer I finally got it to connect in flash mode and flashed a file...... No change.
At this point maybe I should try a new battery for the hell of it even though this one seems to be working.
Or there is a minute hardware damage somewhere. Maybe the power ic? Or s capacitor?