Database Info

Not bricked but not working.

OK all...so I am new here and was trying to get JB to work on my tablet. I thought I had done the needed research but went wrong somewhere I guess. I tried to follow steps on a site I found from AndroidAuthority dot com (not sure if I am able to post the entire link or no?). I was trying to root and install ClockworkMod Recovery but I guess either something went wrong or I messed something up. From what I have been reading I guess I have not bricked my device since it still tries to load. It currently loops with the Samsung screen. I can still enter the download mode and recovery mode but not sure what I should try next. I tried via Odin again with no luck. Out of the box I was running 4.0.3 but did the OTA update to 4.0.4. Any help would be appreciated.
Thanks from a newbie!

Also I used espresso_recovery.tar.md5 as the recovery image if that helps at all. Thanks again.

Followed the steps from another site. Will follow these later today:
http://forum.xda-developers.com/showthread.php?t=1788625
I guess since I can still use Odin I should be all set. Sorry if this was in the wrong section.

jRower said:
Followed the steps from another site. Will follow these later today:
http://forum.xda-developers.com/showthread.php?t=1788625
I guess since I can still use Odin I should be all set. Sorry if this was in the wrong section.
Click to expand...
Click to collapse
You can use heimdale too. Ive had better luck using that for my phone, never tried my tabley but it should work.
Sent from my SGH-I997 using xda app-developers app

I haven't tried heimdale yet cause I do not want to add more gas to the flames. But I tried the other link I posted and still no luck. Also tried a different SD card to be on the safe side but no luck. Any ideas on what I should do next? Or any other info I can provide that might help?

Keep on trying... it should work sooner or later. Have the samsung drivers? If not install kies. Try other usb ports too.
Sent either from my p113 (gtab 2 7.0) or i997 (Infuse)

Ryanscool said:
Keep on trying... it should work sooner or later. Have the samsung drivers? If not install kies. Try other usb ports too.
Sent either from my p113 (gtab 2 7.0) or i997 (Infuse)
Click to expand...
Click to collapse
Should I keep on with the same procedure or you mean keep letting it boot in a cycle?

I used this with 4.0.4.
http://forum.xda-developers.com/showthread.php?t=1657056
i would suggest you follow from the beginning.
install samsung drivers and kies and odin. run odin as adminstrator.
pay close attention to the mention of the post #325 in the instruction as it what helps you 4.0.4 root process. its difference from 4.0.3.
also if you are on jb. you need to run cwm 6.0 not 5.0 make sure youre uploading the right file into odin.
---------- Post added at 02:05 PM ---------- Previous post was at 02:05 PM ----------
btw youre not bricked don't stress, youll sort it out soon enough

sonikot said:
I used this with 4.0.4.
http://forum.xda-developers.com/showthread.php?t=1657056
i would suggest you follow from the beginning.
install samsung drivers and kies and odin. run odin as adminstrator.
pay close attention to the mention of the post #325 in the instruction as it what helps you 4.0.4 root process. its difference from 4.0.3.
also if you are on jb. you need to run cwm 6.0 not 5.0 make sure youre uploading the right file into odin.
---------- Post added at 02:05 PM ---------- Previous post was at 02:05 PM ----------
btw youre not bricked don't stress, youll sort it out soon enough
Click to expand...
Click to collapse
Thanks...I'll give it a shot! Much appreciated.

Use section B of my guide.

MultipleMonomials said:
Use section B of my guide.
Click to expand...
Click to collapse
Followed all the steps in section B and I am still stuck in a boot loop. Any idea?

Then use the restore to stock procedure. But before you do, tell me: what step did you boot loop on?

Haven't been able to work on this again. I will try and get some time and get back to you. Thanks again for the help.

jRower said:
OK all...so I am new here and was trying to get JB to work on my tablet. I thought I had done the needed research but went wrong somewhere I guess. I tried to follow steps on a site I found from AndroidAuthority dot com (not sure if I am able to post the entire link or no?). I was trying to root and install ClockworkMod Recovery but I guess either something went wrong or I messed something up. From what I have been reading I guess I have not bricked my device since it still tries to load. It currently loops with the Samsung screen. I can still enter the download mode and recovery mode but not sure what I should try next. I tried via Odin again with no luck. Out of the box I was running 4.0.3 but did the OTA update to 4.0.4. Any help would be appreciated.
Thanks from a newbie!
Click to expand...
Click to collapse
Don't use ClockWorkmod, it's not designed specifically for Gtab2... CWM is bad.
you can try flash your gtab2 with ODIN instead

CWM is OFFICIALLY supported now and works good.
Don't fear.

silentvisitor said:
CWM is OFFICIALLY supported now and works good.
Don't fear.
Click to expand...
Click to collapse
Officially supported by WHO? Samsung ?
CWM is not designed for Gtab2. Just ask clockwork if you don't believe it.

Rotundjere said:
Officially supported by WHO? Samsung ?
CWM is not designed for Gtab2. Just ask clockwork if you don't believe it.
Click to expand...
Click to collapse
See here

Boot Loop
So I'm new here, I tried rooting my p3100, flashed cwm with Odin, as it rebooted from there it just keeps rebooting - need help please guys......any lil bit of advice would help - I've read on other posts to flash to the stock ROM, but how do i do this? where do i get the rom......

OK so I am back at it and still not having much luck. I can't get as far as the:
"CWM-based Recovery v6.0.1.0"
Screen.
From here I do not have a recovery file to use. Which should I use for the P3113....At this point I don't even care if I lose all the data on the tablet and go back to stock. Just need it working again and then do some more research on how to do it right..
Thanks again.

Then use Section E of my guide. It will wipe your data and restore your tablet to stock.

[Q] New Member of the Club, now Rooting but not flashing

Hi guys since today im a proud owner of a Galaxy Note 10.1 N8000 stock 4.1.2, but now comes the question, is it possible to Root it without flashing anything?
I only need root access to install a few apps, FolderMount, Titanium, Root explorer, etc.
I own too a Galaxy S2 that I rooted by the method of "rooting without flashing unsecure kernel" is it possible to apply the same method to the Note 10.1?
THANKS for any help given.

pedrohell said:
Hi guys since today im a proud owner of a Galaxy Note 10.1 N8000 stock 4.1.2, but now comes the question, is it possible to Root it without flashing anything?
I only need root access to install a few apps, FolderMount, Titanium, Root explorer, etc.
I own too a Galaxy S2 that I rooted by the method of "rooting without flashing unsecure kernel" is it possible to apply the same method to the Note 10.1?
THANKS for any help given.
Click to expand...
Click to collapse
Welcome to the club. Take a look at all the sections for the tablet and make sure you read the stickies too.
Method #2 and youl be good to go.
http://forum.xda-developers.com/showthread.php?t=1831152

I had already read that stickie and if I have correctly read, Method 2 (and the others) involves Odin and flashing something and that is what I dont want.
Isnt there a way to root without flashing?

pedrohell said:
I had already read that stickie and if I have correctly read, Method 2 (and the others) involves Odin and flashing something and that is what I dont want.
Isnt there a way to root without flashing?
Click to expand...
Click to collapse
Let me ask you this, why no flashing? As far as I know it's either Odin or flash. You need to get a custom recovery on it in order to root.
---------- Post added at 05:31 PM ---------- Previous post was at 05:30 PM ----------
Also with the s2 the recovery and kernel are in one. This is not.

Thanks for your help and time spent helping me, but I think I will pass the root on the Note, I thought there was a more easier/safe method like that on the S2.
Thanks

pedrohell said:
Thanks for your help and time spent helping me, but I think I will pass the root on the Note, I thought there was a more easier/safe method like that on the S2.
Thanks
Click to expand...
Click to collapse
No problem, but it don't get any easier than odin or recovery.

pedrohell said:
Thanks for your help and time spent helping me, but I think I will pass the root on the Note, I thought there was a more easier/safe method like that on the S2.
Thanks
Click to expand...
Click to collapse
There was an Exynos exploit method but Samsung patched the security hole a few updates ago.
The method in the link that was posted does alter your flash count and that can be correct but you are the owner of the device and if you are not comfortable flashing you tablet I wouldn't.
I have flashed mine and tried a few rom's but I always ended up resetting my flash counter and going back to stock.
Folder mount works great and that was the reason I rooted in the first place but you can store your files on the ext drive and transfer them back and forth manually but I found with my fast wifi I'm better off re-downloading the data along with "Helium - App Sync and Backup" to backup and restore my data and you do not need root, only draw back is that you have to have a computer connection for backup and restore to work.
.

Yes, its just a matter of not feeling confortable, and there is also the risk of blocking the camera. (had a similar issue with 4.1.2 on S2 needed to downgrade to 4.0.4).
But it seeems to me a bit odd that to grant root access we need to flash the rom.

I don't think you read that right. You're not flashing a ROM, just a custom recovery through ODIN, then a root app. It's actually very simple. (Any simpler and I would be concerned about rogue app exploits)
Fyi: I'm also new to Samsung devices and bought my tablet this week. Rooted it this morning by following the stickies, but sticking with the stock ROM for now. I'm more than happy with the tablet so far.
Sent from my GT-N8013 using xda app-developers app

pedrohell said:
Yes, its just a matter of not feeling confortable, and there is also the risk of blocking the camera. (had a similar issue with 4.1.2 on S2 needed to downgrade to 4.0.4).
But it seeems to me a bit odd that to grant root access we need to flash the rom.
Click to expand...
Click to collapse
There is no flashing a rom with method 2. You Odin the custom recovery then you have to flash the superuser into the system. You need superuser to get root and Odin is the easiest way.
Trust me we have all been in your shoes about being nervous, I've been doing this a long time and this method is really easy.

You can also use this method - http://forum.xda-developers.com/showthread.php?t=1957002
It does require ODIN but as has been stated this is the norm. You are not replacing any kernels or flashing another rom, you are just adding the root components. Using this method also leaves stock recovery intact...
If you woory about flash counter then run triangleaway after to reset the flash counter and recoveries....
I found doing this, doing a factory reset from settings then reflashing the Stock rom using Mobile ODIN pro gave me a stock standard, but rooted, rom with all statuses "Official" and 0 flash count....
A lot of work I know but then worthwhile things generally require it...

Ok, I followed the Method 2 made everything like on video, after pressing Power+Volume Up, I entered on STOCK Recovery, not the CWM,even so, I apply the .zip and I get:
MANUAL MODE
--Appling Multi-CSC....
Applied the CSC-code:LUX
Successfully applied multi-CSC.
--Install /sdcard....
Finding update package....
Opening update package....
Verifying update package.....
E:FAILED TO VERIFY WHOLE-FILE SIGNATURE
E:FAILED TO VERIFY WHOLE-FILE SIGNATURE
E:signature verification failed
I also retryed and turned off auto-reboot in Odin before starting the process but I get the same thing, now what should I do?
Its not rootable?

Ok, Its finally rooted, What I had to do,
On Odin unthick auto-reboot, When Odin finished doing its thing, dont shutdown the Tablet but press Power+Volume Up and go directly to CWM recovery and there follow the rest of instructions.
Thanks to everybody that took time to help me, thats why I love this forum.
A BIG THANK YOU.

pedrohell said:
I had already read that stickie and if I have correctly read, Method 2 (and the others) involves Odin and flashing something and that is what I dont want.
Isnt there a way to root without flashing?
Click to expand...
Click to collapse
I see that I'm probably too late now to answer the OP.
But maybe others can be interested.
I find that the easiest way to root (without odin and without installing a custom recovery) is Framaroot.
It uses some Exynos exploits, and has been also recently updated by the developer to counteract Samsung's patches.
It may work or it may not work on some devices and with some of the more recent firmware.
In any case giving it a try doesn't cost anything. It's just an app.
If it works the app can also be used to temporarily remove the root.
For me it worked with Firmware N8000XXCLL3 and I know that it works with some more recent fw too.
Furthermore it doesn't change the counter and even the Devices Status remains "Official". Well, actually the devices status may change to "Custom" after few days with the tablet on, but it returns Official after a simple reboot.

pedrohell said:
Ok, Its finally rooted, What I had to do,
On Odin unthick auto-reboot, When Odin finished doing its thing, dont shutdown the Tablet but press Power+Volume Up and go directly to CWM recovery and there follow the rest of instructions.
Thanks to everybody that took time to help me, thats why I love this forum.
A BIG THANK YOU.
Click to expand...
Click to collapse
Awesome to hear! I ran into the same thing you did, forgot to go straight to recovery from odin.
Enjoy!

Stuck
Please help..
I get this error when i try to install: View attachment 2066244
What did i do wrong ?

brix696 said:
Please help..
I get this error when i try to install: View attachment 2066244
What did i do wrong ?
Click to expand...
Click to collapse
I don't use CWM, but see if there is a signature seeing to turn it off. Also make sure your md5 of the zip is correct.

brix696 said:
Please help..
I get this error when i try to install: View attachment 2066244
What did i do wrong ?
Click to expand...
Click to collapse
What were your options on the page right before that? What option did you select to initiate that?
Maybe try using the files from here instead:
http://droidviews.com/2013/root-and...ung-galaxy-note-10-1-n8000-n8010-n8013-n8020/

bigtoysrock said:
I don't use CWM, but see if there is a signature seeing to turn it off. Also make sure your md5 of the zip is correct.
Click to expand...
Click to collapse
Where should i look for a signature ? I have downloaded the file 3 times, just to manke sure that i wasen't bad.
Before that, it was the page where i choose "apply update from external storage"
I have tryed the CF, still the same

brix696 said:
Where should i look for a signature ? I have downloaded the file 3 times, just to manke sure that i wasen't bad.
Before that, it was the page where i choose "apply update from external storage"
I have tryed the CF, still the same
Click to expand...
Click to collapse
I would use the touch cwm, and what rom are you trying to install?

Cant update phone/flash with odin/root

*Copied mostly from my topic on AndroidForums*
/*from June 27th, thread start*/
So I found out that on the 25th or 26th there was an update for the Verizon GS3. Every time I try to update, it gives me this error (see below) after it reboots. I should also probably note that when it reboots, you briefly see "Booting into recovery" in the top left corner, though it doesn't actually boot into recovery. I was rooted, but I did a full unroot with SuperSU, and it still doesn't work. I dont want to flash a stock image because of all my app data that I do not want to lose.
Here is what the update screen looks like: i . imgur. com/oC04moq.png
And after the "update": i . imgur. com/oC04moq.png
Scroll down a little bit on that same box: i . imgur. com/iSqwQl0.jpg
Please someone help me! This is driving me crazy!
/End post 1\
Click to expand...
Click to collapse
/revive post October 6th\
So its been about 3 months now. Problem still persists. Again, I can not flash anything with ODIN(307), or update the phone. I have tried with Kies and in the phone. I can boot into download mode and recovery mode fine. Any help would again be greatly appreciated. I don't have access to my pc atm but any suggestions are still appreciated.
*The phone runs flawlessly, I just want to be able to root again *
/end post
Click to expand...
Click to collapse
/suggestion from user
"I would wind this back to the start.
It may not be just a phone issue. Uninstal kies and any android drivers and reboot.
Try this first:
★[8/27] [Casual] [Root, Unlock, Recovery] Vzw S3 Toolkit or 1-Click!! [ALL OTA's]★ - xda-developers
For the Verizion only. Anyone else thinking of using this start a new thread!!"
Click to expand...
Click to collapse
and my respose after trying: gyazo . com/3827e1487bf8cb3aeb0871b946fde785.png
Been on this for about 10mins, videos I have seen have done nearly instantly. I don't want to disconnect anything...
EDIT: I tried again twice. Same issue. I'm going to uninstall all drivers etc and try again.
Nup, still not working. Any more suggestions?
So far I have tried:
Odin(for root)
Kies(for updating)
Casual
Uninstalling kies/drivers and reinstalling and retrying all
All recognize the device, but nothing happens.
Click to expand...
Click to collapse
Now I'm here. I've never seen or heard anything like this before. Please post any suggestions you might have. I am down to try almost anything.
Sorry if I'm breaking any rules or anything. I just want this resolved.
And sorry for long post.

I'm assuming you've done all this with the same USB cable? Try a different cable (preferably the included one), different usb port, and also a different computer.
Sent from my SCH-I535 using Tapatalk 4

I can't even tell what is going on, this post is very confusing. Is Odin giving a fail message?
1. Odin should work, if it doesn't in a normal circumstance, then this method will work http://forum.xda-developers.com/showthread.php?t=1840030. This is will wipe all your data, but you'll be good to go from there.
2. Why did you unroot through super su? What rom are you running right now?
3. You can try using this image:
http://forum.xda-developers.com/showthread.php?t=1974114, then after you do this method you can run casual and root from there, while preserving your data.
Sent from my SCH-I535 using Tapatalk 2

Thanks to both of you!!!!!! I used a different port on my PC, and used the nowipe image BadUsername posted, and now I'm rooted, custom recovery, unlocked bootloader, and no data loss!! Again, thank you so much.

:highfive: yea teamwork! And last thing I'll suggest is to backup your IMEI if you haven't done so before.

SM-P905 new update

Did anyone take the September-october update?
(Italy / Nordic countries /switzerland/ slovakia/ poland/ portugal)
Pda- P905XXUANH3
I'm trying to understand if it messes up the towelroot or not.
Thanks.

I took the plunge, but Towelroot refused to work on the new rom. Apart from that the tablet started rebooting spontaneously every 15 mins or so after I installed the update.
Def NOT recommended to install it.
I had to downgrade to the previous rom using Odin and now I'm back to normal.
Hope that helps.

etibon said:
I took the plunge, but Towelroot refused to work on the new rom. Apart from that the tablet started rebooting spontaneously every 15 mins or so after I installed the update.
Def NOT recommended to install it.
I had to downgrade to the previous rom using Odin and now I'm back to normal.
Hope that helps.
Click to expand...
Click to collapse
thanks...

Same here wish I read this post before updating

I tried to root my tablet but it failed and I had to Odin back to stock. I've been running like that for months yet I took the update yesterday and it went flawlessly.
Sent from my SM-P900 using XDA Free mobile app

Vlip3 said:
I tried to root my tablet but it failed and I had to Odin back to stock. I've been running like that for months yet I took the update yesterday and it went flawlessly.
Sent from my SM-P900 using XDA Free mobile app
Click to expand...
Click to collapse
you are on the wifi version..

can i root the nh3 update with cf-autoroot or fail too??

Did not try cf root before I reverted back...If you already tripped knox Please give it a go and let us know

milan188 said:
Did not try cf root before I reverted back...If you already tripped knox Please give it a go and let us know
Click to expand...
Click to collapse
Another possibility could be to install H3, then flash xxuanc3 firmware, towelroot it without tripping knox and then reflash h3 firmware. A similar procedure works on s4, but unfortunately I'm not enough expert on firmware and odin stuffs, so I am not sure if there are possibilities to brick the device and how to prepare the extracted firmwares for odin flashing. I found some procedures that should work for doing that but nothing about a way to check in advance if such procedures are sure.
A developer should be able to do this, but, in wich part of the forum this can be asked?

.?

dangua said:
can i root the nh3 update with cf-autoroot or fail too??
Click to expand...
Click to collapse
Did you finally try cf autoroot with NH3 update?

andr123a said:
Did you finally try cf autoroot with NH3 update?
Click to expand...
Click to collapse
no.. i don't try because i don't find cf autoroot for this update

Damn......
I would like to understand if we have a chance to root it....I asked directly chainfire if we could use cf autoroot with this new firmware...but no answer
Regarding towelroot someone says ok, other say it doesn't work...
My note has 1 week of life, I'm quite afraid to create problems...

andr123a said:
Damn......
I would like to understand if we have a chance to root it....I asked directly chainfire if we could use cf autoroot with this new firmware...but no answer
Regarding towelroot someone says ok, other say it doesn't work...
My note has 1 week of life, I'm quite afraid to create problems...
Click to expand...
Click to collapse
towelroot doesn't work with last update...i try it but nothing to do...

My device is rooted and I installed new update (KOT49H.P905XXUANH3) by flashing full ROM by odin, without wiping.
Now I'm experiencing random reboots (pretty often). The question is - is it because it was dirty-flesh or just new updated rom is not working properly?
Are you also experiencing such problems?

perce_ption said:
My device is rooted and I installed new update (KOT49H.P905XXUANH3) by flashing full ROM by odin, without wiping.
Now I'm experiencing random reboots (pretty often). The question is - is it because it was dirty-flesh or just new updated rom is not working properly?
Are you also experiencing such problems?
Click to expand...
Click to collapse
try to open super su and when it ask you to disable knox tap on delete
Inviato dal mio SM-P905

rooted NH3 with towelroot
Ok,
I successfully rooted NH3 with towelroot, acting as pointed out in my first post. The only problem I had is that once you load the XXUANC3 firmware you loose the wifi connectivity, obliging to rely on your provider's internet connectivity to complete the rooting proicess.
To remove the knox and update stuff I used a debloating script that in another thread for the sm-p905, but no other stuff, as this script was written for the previus version of the firmware.
No knox trip nor reboots, so far.

aviator1 said:
Ok,
I successfully rooted NH3 with towelroot, acting as pointed out in my first post. The only problem I had is that once you load the XXUANC3 firmware you loose the wifi connectivity, obliging to rely on your provider's internet connectivity to complete the rooting proicess.
To remove the knox and update stuff I used a debloating script that in another thread for the sm-p905, but no other stuff, as this script was written for the previus version of the firmware.
No knox trip nor reboots, so far.
Click to expand...
Click to collapse
CAN you write instructions for what you did? I can't fully understand what to do.
Thanks.

No WIFI after update
Hi Guys,
I don't have root, and I only use it via WIFI.
However, after today's update, it does not connect to WIFI nor it recognizes my WIFI name.
I don't know what to do.
Many thanks in advance.
Hugo

snir2 said:
CAN you write instructions for what you did? I can't fully understand what to do.
Thanks.
Click to expand...
Click to collapse
- Check that developer mode is enabled
- Download and install Towelroot and supersu
- Shut down the tablet
- Reboot (Home Key + Volume Down + Poweron, then volume UP) in download mode and flash with Odin 3.07 or 3.09 the latest firmware (XXUANH3).
- Shut Down the tablet
- Reboot the tablet and flash only the Kernel of the previous firmware (XXUANC3)
- You loose the WIFI connectivity, so connect to the internet through your phone provider internet connection, then - Launch Towelroot and root your tablet, Then launch Supersu and disable Knox. The tablet may freeze at this point (didn't happen to me), but in any case you have to shut down.
- Reboot in download mode and flash the latest firmware (XXUANC3).
- At this point you're done, but, to avoid random reboots you have to completely remove Knox, something that you can do with several tools. I used a debloating tool for SM-P905 that I found in this forum.
About the Kernel files needed for this procedure, I tried to attach them to my posts, but it looks like I'm not yet enabled to do that (too few posts, may be).
To prepare them from the original firmware files I used a Windows script called TAR_MD5_PAKAGER, that you can find searching in this forum.
Hope that the above results clearer than my previous posts
---------- Post added at 12:50 AM ---------- Previous post was at 12:45 AM ----------
hfmartins said:
Hi Guys,
I don't have root, and I only use it via WIFI.
However, after today's update, it does not connect to WIFI nor it recognizes my WIFI name.
I don't know what to do.
Many thanks in advance.
Hugo
Click to expand...
Click to collapse
I'd reflash the tablet

[Q] n915p cf auto root fails?

I just got my hands on the sprint note edge (such an amazing device!) and i've been trying to root it with cf auto root but every time i flash with Odin, it fails with the progress bar on the phone only about halfway. Any suggestions? I'm on the latest firmware, nk1, which matches the version listed on the cf auto root site.
Thanks in advance
Edit:
HEY, YOU. YEAH YOU. READ THIS BEFORE YOU POST:
We figured out the solution quite a while back, but I know no one wants to read the entire thread, so here's a summary c/p'd from the end:
But to summarize, we've been able to get root by flashing CF auto root, letting it fail, then immediately flashing TWRP. To fix any issues encountered with xposed framework (stock sms not working, lagginess, installations taking forever, etc.), freeze with titanium/delete data for shealth, health services, and private mode, install securestorage module in xposed or use the equivalent option in Wanam, reboot, and unfreeze.
Click to expand...
Click to collapse
Now if you've tried this and you're still having issues, then post ahead. If you haven't tried this, or need help with specifics, read the thread. There's a post by me halfway through or so with 4 XDA links in it. If you want more info on the problem with xposed, check out those links.

jooniloh said:
I just got my hands on the sprint note edge (such an amazing device!) and i've been trying to root it with cf auto root but every time i flash with Odin, it fails with the progress bar on the phone only about halfway. Any suggestions? I'm on the latest firmware, nk1, which matches the version listed on the cf auto root site.
Thanks in advance
Click to expand...
Click to collapse
You may check out this thread: http://forum.xda-developers.com/note-edge/general/easy-steps-stock-odin-n915tuvu1anjl-sm-t2943993
Its for a Tmobile version, but it looks like they may have had the same issue, but figured it out... I haven't tried it yet, but am REAL close to giving it a shot. It looks to me that flashing TWRP after the fail, may be the key to making it successful? I have the Sprint model too, but am still on NJL build.

Does TWRP fully support the note edge yet? Some of those steps (disabling screen timeout) make it seem otherwise. I'm usually hesitant to go for workarounds rather than actual fixes... :/ tell me if you do try it out though.

Next1776 said:
You may check out this thread: http://forum.xda-developers.com/note-edge/general/easy-steps-stock-odin-n915tuvu1anjl-sm-t2943993
Its for a Tmobile version, but it looks like they may have had the same issue, but figured it out... I haven't tried it yet, but am REAL close to giving it a shot. It looks to me that flashing TWRP after the fail, may be the key to making it successful? I have the Sprint model too, but am still on NJL build.
Click to expand...
Click to collapse
I'm not sure about TWRP, but was going to try the Note 4 version. I updated to NK1 now, so may give it a whirl... Nah - You go first, lol. I'll post if I decide to go through with it.:good:

Next1776 said:
I'm not sure about TWRP, but was going to try the Note 4 version. I updated to NK1 now, so may give it a whirl... Nah - You go first, lol. I'll post if I decide to go through with it.:good:
Click to expand...
Click to collapse
Too Funny.. I heard the note 4 files where working from an undisclosed source.. I haven't powered mine on yet, Still waiting on a screen protector and case.. Lol

z31k said:
Too Funny.. I heard the note 4 files where working from an undisclosed source.. I haven't powered mine on yet, Still waiting on a screen protector and case.. Lol
Click to expand...
Click to collapse
to clarify, is that the SPRINT note 4 cf auto root files you're referring to?
Just checked. Sprint Note 4 cf auto root is for NIE. Is this even safe to try on the Edge?

jooniloh said:
to clarify, is that the SPRINT note 4 cf auto root files you're referring to?
Just checked. Sprint Note 4 cf auto root is for NIE. Is this even safe to try on the Edge?
Click to expand...
Click to collapse
That's what I was told.. Sprint note 4 auto root...
I would wait up if you feel uneasy about it.. lol
at least until they have a edge auto root. I may try the note 4 sometime next week when the screen protector comes in..

z31k said:
That's what I was told.. Sprint note 4 auto root...
I would wait up if you feel uneasy about it.. lol
at least until they have a edge auto root. I may try the note 4 sometime next week when the screen protector comes in..
Click to expand...
Click to collapse
There is an edge auto root. It just happens to be failing at the moment (for sprint anyways). There are workarounds for the T-Mobile auto root (which is also failing) but we're all too chicken here to try it on our new shiney Note Edges . . . Lol

jooniloh said:
There is an edge auto root. It just happens to be failing at the moment (for sprint anyways). There are workarounds for the T-Mobile auto root (which is also failing) but we're all too chicken here to try it on our new shiney Note Edges . . . Lol
Click to expand...
Click to collapse
Lmfao!!

OK. I wasn't too chicken... and should have been! HELP!!!!!
I attempted the ODIN flash with the proper CF that states that it is for the Sprint Edge... and now have a soft (I hope) bricked phone. The message I have on the screen right now is:
"Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again."
Like I said.... HELP!!!!!
I'm not familiar with KIES but I guess I'll get that way....
Update: I am able to get into download mode... now now if I could just get my hands on a STOCK ROM to ODIN... ANYONE?

beejmeister said:
OK. I wasn't too chicken... and should have been! HELP!!!!!
I attempted the ODIN flash with the proper CF that states that it is for the Sprint Edge... and now have a soft (I hope) bricked phone. The message I have on the screen right now is:
"Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again."
Like I said.... HELP!!!!!
I'm not familiar with KIES but I guess I'll get that way....
Update: I am able to get into download mode... now now if I could just get my hands on a STOCK ROM to ODIN... ANYONE?
Click to expand...
Click to collapse
Nope. That's what we all tried and it failed for us too. We're trying to figure out a fix or alternative to this. Anyways, to fix your device, take the .tar.md5 file found inside the CF auto root directory and open it with an archiver like 7zip. Extract the recovery.img to somewhere and run this tool on it. Then open up the odin included in CF auto root and choose the recovery.tar.md5 you created rather than the usual file. Flash in download mode and you're good to go.

jooniloh said:
Nope. That's what we all tried and it failed for us too. We're trying to figure out a fix or alternative to this. Anyways, to fix your device, take the .tar.md5 file found inside the CF auto root directory and open it with an archiver like 7zip. Extract the recovery.img to somewhere and run this tool on it. Then open up the odin included in CF auto root and choose the recovery.tar.md5 you created rather than the usual file. Flash in download mode and you're good to go.
Click to expand...
Click to collapse
If there is one thing I've learned in my many years on XDA... DON'T PANIC! Someone will help you. I didn't panic... You helped me hugely. Figured I'd go home and reactivate my Note 3... but didn't even have to do that. THANKS jooniloh! Many thanks...

beejmeister said:
If there is one thing I've learned in my many years on XDA... DON'T PANIC! Someone will help you. I didn't panic... You helped me hugely. Figured I'd go home and reactivate my Note 3... but didn't even have to do that. THANKS jooniloh! Many thanks...
Click to expand...
Click to collapse
No problem. Glad I could help. Now let's just hope for a stable root method soon! Out of curiosity, are you also on NK1? I wonder if anyone who didn't upgrade was able to get root successfully . . .

beejmeister said:
OK. I wasn't too chicken... and should have been! HELP!!!!!
I attempted the ODIN flash with the proper CF that states that it is for the Sprint Edge... and now have a soft (I hope) bricked phone. The message I have on the screen right now is:
"Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again."
Like I said.... HELP!!!!!
I'm not familiar with KIES but I guess I'll get that way....
Update: I am able to get into download mode... now now if I could just get my hands on a STOCK ROM to ODIN... ANYONE?
Click to expand...
Click to collapse
Man, this is happening fast... I just got it done successfuly rooting my Sprint Edge. Don't freak, follow the instructions on this thread which works on Tmobile devices. I didn't install the SD card fix file yet, but may if I need it. You are basically starting at the FAIL point of that thread. Although you need the SU file on your phone, which you may be able to get it by putting it on a Microsd and accessing it from recovery that way. Good Luck, and don't panic, lol.
EDIT: See my post here : http://forum.xda-developers.com/note-edge/general/info-galaxy-note-edge-sm-n915-t2945942 for more details on what worked for me

jooniloh said:
No problem. Glad I could help. Now let's just hope for a stable root method soon! Out of curiosity, are you also on NK1? I wonder if anyone who didn't upgrade was able to get root successfully . . .
Click to expand...
Click to collapse
Yup! On NK1. Did the update yesterday when I first got the phone. Guess we're seeing a pattern here!
---------- Post added at 06:16 PM ---------- Previous post was at 06:15 PM ----------
Next1776 said:
Man, this is happening fast... I just got it done successfuly rooting my Sprint Edge. Don't freak, follow the instructions on this thread which works on Tmobile devices. I didn't install the SD card fix file yet, but may if I need it. You are basically starting at the FAIL point of that thread. Although you need the SU file on your phone, which you may be able to get it by putting it on a Microsd and accessing it from recovery that way. Good Luck, and don't panic, lol.
Click to expand...
Click to collapse
OK. Now I'll ask THE question: Next1776, are YOU on NK1?

Next1776 said:
Man, this is happening fast... I just got it done successfuly rooting my Sprint Edge. Don't freak, follow the instructions on this thread which works on Tmobile devices. I didn't install the SD card fix file yet, but may if I need it. You are basically starting at the FAIL point of that thread. Although you need the SU file on your phone, which you may be able to get it by putting it on a Microsd and accessing it from recovery that way. Good Luck, and don't panic, lol.
Click to expand...
Click to collapse
Can you tell me exactly what you did step by step? Also are you on the latest sprint firmware?
And what version of TWRP did you use?

beejmeister said:
Yup! On NK1. Did the update yesterday when I first got the phone. Guess we're seeing a pattern here!
---------- Post added at 06:16 PM ---------- Previous post was at 06:15 PM ----------
OK. Now I'll ask THE question: Next1776, are YOU on NK1?
Click to expand...
Click to collapse
NK1
---------- Post added at 06:12 PM ---------- Previous post was at 05:47 PM ----------
jooniloh said:
Can you tell me exactly what you did step by step? Also are you on the latest sprint firmware?
And what version of TWRP did you use?
Click to expand...
Click to collapse
I actually downloaded the Chainfire file yesterday for the SM N915P, but was still too chicken to try it. After I saw this thread today, I decided to go for it. All I basically did was follow the instructions in TEKHD 's thread for the SM915T.
-Dowloaded Chainfire's Sprint AutoRoot file, Unzipped it.
-Put phone in download mode, selcted the Chainfire's Sprint AutoRoot tar file and hit Start.
-ODIN flashed "FAIL".
-I then flashed a 2.8.0.0 TWRP file for the Note 4, which ODIN said was successful, but it would not boot into recovery (so don't do that).
-I flashed the 2.8.1.1 Tmobile TWRP file from TEKHD's thread, ODIN said success.
-Booted into recovery, adjusted settings for brightness in TWRP, (TWRP was acting really flaky, but I pressed on) I couldn't find the UPDATE-SuperSU-v2.16.zip file in recovery, (I put the file on my removable SD card) so I rebooted recovery, and this time was able to find the UPDATE-SuperSU-v2.16.zip, and flashed it.
-Wiped cache/ Dalvik Cache. Hit Reboot-> System, TWRP said it didn't appear to have root, do I want to root? Hit yes, go , whatever, it rebooted, let settle for a few minutes, and ROOT was born!
Hope that helps and I didn't miss something, but thats how it went down for me.
To sum it up, Follow TEKHD's Tmobile thread, with the exception of the Tmobile Chainfire file, (use the Sprint one obviously) I also did not flash the SD card fix from that thread.
Let me know if you have questions, but I will have to bug out for a while here until this evening...
Good Luck everyone!

Next1776 said:
NK1
---------- Post added at 06:12 PM ---------- Previous post was at 05:47 PM ----------
I actually downloaded the Chainfire file yesterday for the SM N915P, but was still too chicken to try it. After I saw this thread today, I decided to go for it. All I basically did was follow the instructions in TEKHD 's thread for the SM915T.
-Dowloaded Chainfire's Sprint AutoRoot file, Unzipped it.
-Put phone in download mode, selcted the Chainfire's Sprint AutoRoot tar file and hit Start.
-ODIN flashed "FAIL".
-I then flashed a 2.8.0.0 TWRP file for the Note 4, which ODIN said was successful, but it would not boot into recovery (so don't do that).
-I flashed the 2.8.1.1 Tmobile TWRP file from TEKHD's thread, ODIN said success.
-Booted into recovery, adjusted settings for brightness in TWRP, (TWRP was acting really flaky, but I pressed on) I couldn't find the UPDATE-SuperSU-v2.16.zip file in recovery, (I put the file on my removable SD card) so I rebooted recovery, and this time was able to find the UPDATE-SuperSU-v2.16.zip, and flashed it.
-Wiped cache/ Dalvik Cache. Hit Reboot-> System, TWRP said it didn't appear to have root, do I want to root? Hit yes, go , whatever, it rebooted, let settle for a few minutes, and ROOT was born!
Hope that helps and I didn't miss something, but thats how it went down for me.
To sum it up, Follow TEKHD's Tmobile thread, with the exception of the Tmobile Chainfire file, (use the Sprint one obviously) I also did not flash the SD card fix from that thread.
Let me know if you have questions, but I will have to bug out for a while here until this evening...
Good Luck everyone!
Click to expand...
Click to collapse
No need to flash the SD card fix. there's apps on the play store that will patch the necessary files for that (and you can delete the app afterwards). Interesting that the TMO twrp worked . . . Someone should try that with the SPRINT twrp 2.8.1.1 found here.
Edit: I tried repeatedly to flash both 2.8.1.1 and 2.8.1.0 versions of the SPRINT NOTE 4 twrp and odin consistently crashed on "File analysis".
Edit: I took the plunge and went with the tmobile method. Nothing went wrong. Everything seems to be working fine. The TMO Note 4 recovery is annoying though (two strips of white on both sides of the screen). I didn't have any issues with how it ran like Next1776 did though.
Edit: I'm experiencing some odd issues. The primary one is that anything I install through xposed or f-droid takes FOREVER to install. Anyone else getting this?

jooniloh said:
No need to flash the SD card fix. there's apps on the play store that will patch the necessary files for that (and you can delete the app afterwards). Interesting that the TMO twrp worked . . . Someone should try that with the SPRINT twrp 2.8.1.1 found here.
Edit: I tried repeatedly to flash both 2.8.1.1 and 2.8.1.0 versions of the SPRINT NOTE 4 twrp and odin consistently crashed on "File analysis".
Edit: I took the plunge and went with the tmobile method. Nothing went wrong. Everything seems to be working fine. The TMO Note 4 recovery is annoying though (two strips of white on both sides of the screen). I didn't have any issues with how it ran like Next1776 did though.
Edit: I'm experiencing some odd issues. The primary one is that anything I install through xposed or f-droid takes FOREVER to install. Anyone else getting this?
Click to expand...
Click to collapse
BUt just to confirm, jooniloh.... you do have confirmable root? Guess my clue should be that you are using xposed.... but just wanted to confirm before I went down the rabbit hole....

jooniloh said:
No need to flash the SD card fix. there's apps on the play store that will patch the necessary files for that (and you can delete the app afterwards). Interesting that the TMO twrp worked . . . Someone should try that with the SPRINT twrp 2.8.1.1 found here.
Edit: I tried repeatedly to flash both 2.8.1.1 and 2.8.1.0 versions of the SPRINT NOTE 4 twrp and odin consistently crashed on "File analysis".
Edit: I took the plunge and went with the tmobile method. Nothing went wrong. Everything seems to be working fine. The TMO Note 4 recovery is annoying though (two strips of white on both sides of the screen). I didn't have any issues with how it ran like Next1776 did though.
Edit: I'm experiencing some odd issues. The primary one is that anything I install through xposed or f-droid takes FOREVER to install. Anyone else getting this?
Click to expand...
Click to collapse
Awesome. Glad you are able to join the party!
I'm not having any issues right now. I have installed Xposed and Wanam without any issues so far. I did disable Knox and Secure storage with Wanam (under security hacks) as another poster suggested. Maybe also try wiping Cache and dalvik in recovery ? Hopefully we will have a stable custom recovery available soon. I say stable, but I guess this one is "stable" - its just not real pretty...