Good my phone has suddenly been hung and when forced reboot is then left in the logo of motorola and it's not from there, I tried to make this tutorial and "appears" that does everything well but then when rebooting just does not start as usual
When trying to enter the recovery says "boot up failed" and tried to install a custom recovery and I get the same
angelgzg said:
Good my phone has suddenly been hung and when forced reboot is then left in the logo of motorola and it's not from there, I tried to make this tutorial and "appears" that does everything well but then when rebooting just does not start as usual
When trying to enter the recovery says "boot up failed" and tried to install a custom recovery and I get the same
Click to expand...
Click to collapse
Try to reflash the stock firmware or, even better, the 4.4.4 of your stock firmware.
oversleeper said:
Try to reflash the stock firmware or, even better, the 4.4.4 of your stock firmware.
Click to expand...
Click to collapse
Where I can download a 4.4.4 firmware and not a full upgrade? and 4.4.3 and try anything
angelgzg said:
Where I can download a 4.4.4 firmware and not a full upgrade? and 4.4.3 and try anything
Click to expand...
Click to collapse
Here
oversleeper said:
Here
Click to expand...
Click to collapse
I get these errors trying
hab check failed for boot
hab check failed for recovery
angelgzg said:
I get these errors trying
hab check failed for boot
hab check failed for recovery
Click to expand...
Click to collapse
That's because you're flashing a non stock firmware. Just ignore that error. Run all commands and all should work properly.
oversleeper said:
That's because you're flashing a non stock firmware. Just ignore that error. Run all commands and all should work properly.
Click to expand...
Click to collapse
This error also should ignore it?
piv signed invalid system image
Just do not start everything but it stays on the logo and I can not get into the recovery?
I'm thinking that the problem is hardware: ((((
angelgzg said:
This error also should ignore it?
piv signed invalid system image
Just do not start everything but it stays on the logo and I can not get into the recovery?
I'm thinking that the problem is hardware: ((((
Click to expand...
Click to collapse
Run the command fastboot.exe getvar all or mfastboot.exe getvar all and post the result.
oversleeper said:
Run the command fastboot.exe getvar all or mfastboot.exe getvar all and post the result.
Click to expand...
Click to collapse
C:\Users\Usuario\Desktop\Minimal ADB and Fastboot>mfastboot.exe getvar all
version: 0.5
version-bootloader: 4111
product: falcon
secure: yes
hwrev: 0x83C0
radio: 0x1
emmc: 16GB Sandisk REV=06 PRV=07 TYPE=17
ram: 1024MB Samsung S4 SDRAM DIE=4Gb
cpu: MSM8226 CS
serialno: TA93005UU8
cid: 0x0009
channelid: 0x00
uid: C3A9C5020F000000000000000000
unlocked: no
iswarrantyvoid: no
mot_sst: 0
max-download-size: 536870912
reason: Volume down key pressed
imei:
meid:
date:
sku:
iccid:
cust_md5:
max-sparse-size: 268435456
current-time: "Wed Aug 6 0:23: 7 UTC 2014"
ro.build.fingerprint[0]: motorola/falcon_retuglb/falcon_umt
ro.build.fingerprint[1]: s:4.4.3/KXB21.14-L1.32/33:user/rel
ro.build.fingerprint[2]: ease-keys
ro.build.version.full[0]: Blur_Version.210.12.32.falcon_umt
ro.build.version.full[1]: s.Retail.en.US
ro.build.version.qcom[0]: AU_LINUX_ANDROID_LNX.LA.3.5.1_RB1
ro.build.version.qcom[1]: .04.04.02.048.020
version-baseband:
kernel.version[0]: Linux version 3.4.42-g26ca2df ([email protected]
kernel.version[1]: ilclbld54) (gcc version 4.7 (GCC) ) #1 S
kernel.version[2]: MP PREEMPT Fri May 30 11:08:03 CDT 2014
sdi.git: git=MBM-NG-V41.11-0-gdc5aeaf
sbl1.git: git=MBM-NG-V41.11-0-gcff5797
rpm.git: git=MBM-NG-V41.11-0-g71b1aae
tz.git: git=MBM-NG-V41.11-0-ga27c415
aboot.git: git=MBM-NG-V41.11-0-g7d46a5a
qe: qe 0/1
ro.carrier: unknown
all: listed above
finished. total time: 0.155s
angelgzg said:
C:\Users\Usuario\Desktop\Minimal ADB and Fastboot>mfastboot.exe getvar all
version: 0.5
version-bootloader: 4111
product: falcon
secure: yes
hwrev: 0x83C0
radio: 0x1
emmc: 16GB Sandisk REV=06 PRV=07 TYPE=17
ram: 1024MB Samsung S4 SDRAM DIE=4Gb
cpu: MSM8226 CS
serialno: TA93005UU8
cid: 0x0009
channelid: 0x00
uid: C3A9C5020F000000000000000000
unlocked: no
iswarrantyvoid: no
mot_sst: 0
max-download-size: 536870912
reason: Volume down key pressed
imei:
meid:
date:
sku:
iccid:
cust_md5:
max-sparse-size: 268435456
current-time: "Wed Aug 6 0:23: 7 UTC 2014"
ro.build.fingerprint[0]: motorola/falcon_retuglb/falcon_umt
ro.build.fingerprint[1]: s:4.4.3/KXB21.14-L1.32/33:user/rel
ro.build.fingerprint[2]: ease-keys
ro.build.version.full[0]: Blur_Version.210.12.32.falcon_umt
ro.build.version.full[1]: s.Retail.en.US
ro.build.version.qcom[0]: AU_LINUX_ANDROID_LNX.LA.3.5.1_RB1
ro.build.version.qcom[1]: .04.04.02.048.020
version-baseband:
kernel.version[0]: Linux version 3.4.42-g26ca2df ([email protected]
kernel.version[1]: ilclbld54) (gcc version 4.7 (GCC) ) #1 S
kernel.version[2]: MP PREEMPT Fri May 30 11:08:03 CDT 2014
sdi.git: git=MBM-NG-V41.11-0-gdc5aeaf
sbl1.git: git=MBM-NG-V41.11-0-gcff5797
rpm.git: git=MBM-NG-V41.11-0-g71b1aae
tz.git: git=MBM-NG-V41.11-0-ga27c415
aboot.git: git=MBM-NG-V41.11-0-g7d46a5a
qe: qe 0/1
ro.carrier: unknown
all: listed above
finished. total time: 0.155s
Click to expand...
Click to collapse
Download this.
oversleeper said:
Download this.
Click to expand...
Click to collapse
Now try this firmware installation and does everything well without errors but when restart is the motorola logo
any way to know if this completely-dead?
angelgzg said:
Now try this firmware installation and does everything well without errors but when restart is the motorola logo
any way to know if this completely-dead?
Click to expand...
Click to collapse
Since you are under warranty the best thing to do is to send it to Motorola...
oversleeper said:
Since you are under warranty the best thing to do is to send it to Motorola...
Click to expand...
Click to collapse
Well I bought it from amazon USA, I'm from Venezuela so I think that's not a possibility? that alternatives do I have? it could be converted into brick? unbrick then?
I also tried unlocking the bootloader and I get the message in purple unlocked and restarted but then goes into fastboot mode as if not done
I changed usb cable and now I get status code = 3, but now does not advance after the warning screen and enter android recovery goes the "no command"
angelgzg said:
Well I bought it from amazon USA, I'm from Venezuela so I think that's not a possibility? that alternatives do I have? it could be converted into brick? unbrick then?
I also tried unlocking the bootloader and I get the message in purple unlocked and restarted but then goes into fastboot mode as if not done
I changed usb cable and now I get status code = 3, but now does not advance after the warning screen and enter android recovery goes the "no command"
Click to expand...
Click to collapse
Ok... now your bootloader is unlocked and your warranty gone, so you can try the next level. Follow my thread. You have to use the bricker script, then when your device will be recognized as qhsusb_bulk I'll give you the tool to reflash the bootloader.
oversleeper said:
Ok... now your bootloader is unlocked and your warranty gone, so you can try the next level. Follow my thread. You have to use the bricker script, then when your device will be recognized as qhsusb_bulk I'll give you the tool to reflash the bootloader.
Click to expand...
Click to collapse
Well now the computer does not pass the warning screen when entering the bootloader and recovery I get the android with exclamation mark and says no command
this is the phone info using this command (mfastboot.exe getvar all)
C:\Minimal ADB and Fastboot>mfastboot.exe getvar all
(bootloader) version: 0.5
(bootloader) version-bootloader: 4111
(bootloader) product: falcon
(bootloader) secure: yes
(bootloader) hwrev: 0x83C0
(bootloader) radio: 0x1
(bootloader) emmc: 16GB Sandisk REV=06 PRV=07 TYPE=17
(bootloader) ram: 1024MB Samsung S4 SDRAM DIE=4Gb
(bootloader) cpu: MSM8226 CS
(bootloader) serialno: TA93005UU8
(bootloader) cid: 0x0009
(bootloader) channelid: 0x00
(bootloader) uid: C3A9C5020F000000000000000000
(bootloader) unlocked: yes
(bootloader) iswarrantyvoid: yes
(bootloader) mot_sst: 3
(bootloader) max-download-size: 536870912
(bootloader) reason: Volume down key pressed
(bootloader) imei:
(bootloader) meid:
(bootloader) date:
(bootloader) sku:
(bootloader) iccid:
(bootloader) cust_md5:
(bootloader) max-sparse-size: 268435456
(bootloader) current-time: "Wed Aug 6 3:39:14 UTC 2014"
(bootloader) ro.build.fingerprint[0]: motorola/falcon_retuglb/falcon_umt
(bootloader) ro.build.fingerprint[1]: s:4.4.3/KXB21.14-L1.32/33:user/rel
(bootloader) ro.build.fingerprint[2]: ease-keys
(bootloader) ro.build.version.full[0]: Blur_Version.210.12.32.falcon_umt
(bootloader) ro.build.version.full[1]: s.Retail.en.US
(bootloader) ro.build.version.qcom[0]: AU_LINUX_ANDROID_LNX.LA.3.5.1_RB1
(bootloader) ro.build.version.qcom[1]: .04.04.02.048.020
(bootloader) version-baseband:
(bootloader) kernel.version[0]: Linux version 3.4.42-g26ca2df ([email protected]
(bootloader) kernel.version[1]: ilclbld54) (gcc version 4.7 (GCC) ) #1 S
(bootloader) kernel.version[2]: MP PREEMPT Fri May 30 11:08:03 CDT 2014
(bootloader) sdi.git: git=MBM-NG-V41.11-0-gdc5aeaf
(bootloader) sbl1.git: git=MBM-NG-V41.11-0-gcff5797
(bootloader) rpm.git: git=MBM-NG-V41.11-0-g71b1aae
(bootloader) tz.git: git=MBM-NG-V41.11-0-ga27c415
(bootloader) aboot.git: git=MBM-NG-V41.11-0-g7d46a5a
(bootloader) qe: qe 0/1
(bootloader) ro.carrier: unknown
all: listed above
finished. total time: 0.054s
C:\Minimal ADB and Fastboot>
oversleeper said:
Ok... now your bootloader is unlocked and your warranty gone, so you can try the next level. Follow my thread. You have to use the bricker script, then when your device will be recognized as qhsusb_bulk I'll give you the tool to reflash the bootloader.
Click to expand...
Click to collapse
after using the recommended script happens happens happens
WARNING: READ CAREFULLY BEFORE YOU PROCEED!
THIS SCRIPT WILL DESTROY THE BOOTLOADER OF YOUR DEVICE.
DO NOT ATTEMPT TO USE UNLESS YOU'RE SURE ABOUT WHAT YOU'RE DOING.
ONLY YOU ARE RESPONSIBLE FOR YOUR ACTIONS.
Do you want to continue [Y / N]?, And
target-sparse max-size: 256MB
sending 'fsg' (102 KB) ...
OKAY [0.027s]
writing 'fsg' ...
OKAY [3.145s]
finished. Total time: 3.175s
target-sparse max-size: 256MB
sending 'rpm' (200 KB) ...
OKAY [0.038s]
writing 'rpm' ...
(bootloader) Preflash validation failed
FAILED (remote failure)
finished. Total time: 0.330s
target-sparse max-size: 256MB
sending 'SBL1' (264 KB) ...
OKAY [0.057s]
writing 'SBL1' ...
OKAY [0.028s]
finished. Total time: 0.088s
target-sparse max-size: 256MB
sending 'sdi' (32 KB) ...
OKAY [0.058s]
writing 'sdi' ...
(bootloader) Preflash validation failed
FAILED (remote failure)
finished. Total time: 0.343s
target-sparse max-size: 256MB
sending 'tz' (400 KB) ...
OKAY [0.084s]
writing 'tz' ...
(bootloader) Preflash validation failed
FAILED (remote failure)
finished. Total time: 0.392s
rebooting ...
finished. Total time: 0.003s
Your device is now hard bricked!
Press any key to continue. . .
But still I can get into fastboot mode and the pc recognizes me as android device
angelgzg said:
after using the recommended script happens happens happens
WARNING: READ CAREFULLY BEFORE YOU PROCEED!
THIS SCRIPT WILL DESTROY THE BOOTLOADER OF YOUR DEVICE.
DO NOT ATTEMPT TO USE UNLESS YOU'RE SURE ABOUT WHAT YOU'RE DOING.
ONLY YOU ARE RESPONSIBLE FOR YOUR ACTIONS.
Do you want to continue [Y / N]?, And
target-sparse max-size: 256MB
sending 'fsg' (102 KB) ...
OKAY [0.027s]
writing 'fsg' ...
OKAY [3.145s]
finished. Total time: 3.175s
target-sparse max-size: 256MB
sending 'rpm' (200 KB) ...
OKAY [0.038s]
writing 'rpm' ...
(bootloader) Preflash validation failed
FAILED (remote failure)
finished. Total time: 0.330s
target-sparse max-size: 256MB
sending 'SBL1' (264 KB) ...
OKAY [0.057s]
writing 'SBL1' ...
OKAY [0.028s]
finished. Total time: 0.088s
target-sparse max-size: 256MB
sending 'sdi' (32 KB) ...
OKAY [0.058s]
writing 'sdi' ...
(bootloader) Preflash validation failed
FAILED (remote failure)
finished. Total time: 0.343s
target-sparse max-size: 256MB
sending 'tz' (400 KB) ...
OKAY [0.084s]
writing 'tz' ...
(bootloader) Preflash validation failed
FAILED (remote failure)
finished. Total time: 0.392s
rebooting ...
finished. Total time: 0.003s
Your device is now hard bricked!
Press any key to continue. . .
But still I can get into fastboot mode and the pc recognizes me as android device
Click to expand...
Click to collapse
Try to download this and run the boot loader tool first. Post the result.
oversleeper said:
Try to download this and run the boot loader tool first. Post the result.
Click to expand...
Click to collapse
It seems like everything I do not change anything
Install recovery shows no error, but still comes out the same and yet so
C:\Users\PC\Desktop\Tools\DeviceInfo>mfastboot getvar all
(bootloader) version: 0.5
(bootloader) version-bootloader: 4111
(bootloader) product: falcon
(bootloader) secure: yes
(bootloader) hwrev: 0x83C0
(bootloader) radio: 0x1
(bootloader) emmc: 16GB Sandisk REV=06 PRV=07 TYPE=17
(bootloader) ram: 1024MB Samsung S4 SDRAM DIE=4Gb
(bootloader) cpu: MSM8226 CS
(bootloader) serialno: TA93005UU8
(bootloader) cid: 0x0009
(bootloader) channelid: 0x00
(bootloader) uid: C3A9C5020F000000000000000000
(bootloader) unlocked: yes
(bootloader) iswarrantyvoid: yes
(bootloader) mot_sst: 3
(bootloader) max-download-size: 536870912
(bootloader) reason: Volume down key pressed
(bootloader) imei:
(bootloader) meid:
(bootloader) date:
(bootloader) sku:
(bootloader) iccid:
(bootloader) cust_md5:
(bootloader) max-sparse-size: 268435456
(bootloader) current-time: "Wed Aug 6 14: 2:16 UTC 2014"
(bootloader) ro.build.fingerprint[0]: motorola/falcon_retuglb/falcon_umt
(bootloader) ro.build.fingerprint[1]: s:4.4.3/KXB21.14-L1.32/33:user/rel
(bootloader) ro.build.fingerprint[2]: ease-keys
(bootloader) ro.build.version.full[0]: Blur_Version.210.12.32.falcon_umt
(bootloader) ro.build.version.full[1]: s.Retail.en.US
(bootloader) ro.build.version.qcom[0]: AU_LINUX_ANDROID_LNX.LA.3.5.1_RB1
(bootloader) ro.build.version.qcom[1]: .04.04.02.048.020
(bootloader) version-baseband:
(bootloader) kernel.version[0]: Linux version 3.4.42-g26ca2df ([email protected]
(bootloader) kernel.version[1]: ilclbld54) (gcc version 4.7 (GCC) ) #1 S
(bootloader) kernel.version[2]: MP PREEMPT Fri May 30 11:08:03 CDT 2014
(bootloader) sdi.git: git=MBM-NG-V41.11-0-gdc5aeaf
(bootloader) sbl1.git: git=MBM-NG-V41.11-0-gcff5797
(bootloader) rpm.git: git=MBM-NG-V41.11-0-g71b1aae
(bootloader) tz.git: git=MBM-NG-V41.11-0-ga27c415
(bootloader) aboot.git: git=MBM-NG-V41.11-0-g7d46a5a
(bootloader) qe: qe 0/1
(bootloader) ro.carrier: unknown
all: listed above
finished. total time: 0.055s
C:\Users\PC\Desktop\Tools\DeviceInfo>pause
Presione una tecla para continuar . . .
angelgzg said:
It seems like everything I do not change anything
Install recovery shows no error, but still comes out the same and yet so
C:\Users\PC\Desktop\Tools\DeviceInfo>mfastboot getvar all
(bootloader) version: 0.5
(bootloader) version-bootloader: 4111
(bootloader) product: falcon
(bootloader) secure: yes
(bootloader) hwrev: 0x83C0
(bootloader) radio: 0x1
(bootloader) emmc: 16GB Sandisk REV=06 PRV=07 TYPE=17
(bootloader) ram: 1024MB Samsung S4 SDRAM DIE=4Gb
(bootloader) cpu: MSM8226 CS
(bootloader) serialno: TA93005UU8
(bootloader) cid: 0x0009
(bootloader) channelid: 0x00
(bootloader) uid: C3A9C5020F000000000000000000
(bootloader) unlocked: yes
(bootloader) iswarrantyvoid: yes
(bootloader) mot_sst: 3
(bootloader) max-download-size: 536870912
(bootloader) reason: Volume down key pressed
(bootloader) imei:
(bootloader) meid:
(bootloader) date:
(bootloader) sku:
(bootloader) iccid:
(bootloader) cust_md5:
(bootloader) max-sparse-size: 268435456
(bootloader) current-time: "Wed Aug 6 14: 2:16 UTC 2014"
(bootloader) ro.build.fingerprint[0]: motorola/falcon_retuglb/falcon_umt
(bootloader) ro.build.fingerprint[1]: s:4.4.3/KXB21.14-L1.32/33:user/rel
(bootloader) ro.build.fingerprint[2]: ease-keys
(bootloader) ro.build.version.full[0]: Blur_Version.210.12.32.falcon_umt
(bootloader) ro.build.version.full[1]: s.Retail.en.US
(bootloader) ro.build.version.qcom[0]: AU_LINUX_ANDROID_LNX.LA.3.5.1_RB1
(bootloader) ro.build.version.qcom[1]: .04.04.02.048.020
(bootloader) version-baseband:
(bootloader) kernel.version[0]: Linux version 3.4.42-g26ca2df ([email protected]
(bootloader) kernel.version[1]: ilclbld54) (gcc version 4.7 (GCC) ) #1 S
(bootloader) kernel.version[2]: MP PREEMPT Fri May 30 11:08:03 CDT 2014
(bootloader) sdi.git: git=MBM-NG-V41.11-0-gdc5aeaf
(bootloader) sbl1.git: git=MBM-NG-V41.11-0-gcff5797
(bootloader) rpm.git: git=MBM-NG-V41.11-0-g71b1aae
(bootloader) tz.git: git=MBM-NG-V41.11-0-ga27c415
(bootloader) aboot.git: git=MBM-NG-V41.11-0-g7d46a5a
(bootloader) qe: qe 0/1
(bootloader) ro.carrier: unknown
all: listed above
finished. total time: 0.055s
C:\Users\PC\Desktop\Tools\DeviceInfo>pause
Presione una tecla para continuar . . .
Click to expand...
Click to collapse
Try the others 2 tools in the package. Don't worry I think your device is ok.
oversleeper said:
Try the others 2 tools in the package. Don't worry I think your device is ok.
Click to expand...
Click to collapse
What other options do I have?
I have managed to brick my Moto G 4G LTE (XT1045 US) while trying to install a custom rom. The device can turn on only in fastboot mode.
I have followed a few tutorial here, here and here which are applicable for MotoG regular edition with no success.
Flashing the partition table for my original US 4.4.3 firmware doesn't work at all. Gives me a 'Preflash validation error'. So I tried the EU 4.4.4 firmware, and in this case the partition table flashes okay, but after that while flashing the boot.img gives the same error.
Code:
G:\Moto G 4g\RET-US-4.4.3>mfastboot flash partition gpt.bin
target max-sparse-size: 256MB
sending 'partition' (32 KB)...
OKAY [ 0.031s]
writing 'partition'...
(bootloader) Preflash validation failed
FAILED (remote failure)
finished. total time: 0.359s
Code:
G:\Moto G 4g\RET-EU-4.4.4>mfastboot flash partition gpt.bin
target max-sparse-size: 256MB
sending 'partition' (32 KB)...
OKAY [ 0.047s]
writing 'partition'...
(bootloader) This may take a few seconds, if a
(bootloader) different partition table is being
(bootloader) flashed since we need to backup
(bootloader) and restore a few partitions
(bootloader) Flashing primary GPT image...
(bootloader) Flashing backup GPT image...
OKAY [ 0.391s]
finished. total time: 0.438s
G:\Moto G 4g\RET-EU-4.4.4>mfastboot flash motoboot motoboot.img
target max-sparse-size: 256MB
sending 'motoboot' (1953 KB)...
OKAY [ 0.109s]
writing 'motoboot'...
(bootloader) flashing tz ...
(bootloader) flashing rpm ...
(bootloader) flashing sdi ...
(bootloader) flashing aboot ...
(bootloader) flashing sbl1 ...
OKAY [ 1.297s]
finished. total time: 1.406s
G:\Moto G 4g\RET-EU-4.4.4>mfastboot flash logo logo.bin
target max-sparse-size: 256MB
sending 'logo' (1060 KB)...
OKAY [ 0.094s]
writing 'logo'...
OKAY [ 0.109s]
finished. total time: 0.203s
G:\Moto G 4g\RET-EU-4.4.4>mfastboot flash boot boot.img
target max-sparse-size: 256MB
sending 'boot' (10240 KB)...
OKAY [ 0.406s]
writing 'boot'...
(bootloader) Preflash validation failed
FAILED (remote failure)
finished. total time: 0.422s
I am also including the result log of 'getvar all' after flashing the 4.4.4 the partition table.
Code:
mfastboot getvar all
(bootloader) version: 0.5
(bootloader) version-bootloader: 4113(*)
(bootloader) product: peregrine
(bootloader) secure: yes
(bootloader) hwrev: 0x82D0
(bootloader) radio: 0x1
(bootloader) emmc: 8GB Sandisk REV=06 PRV=07 TYPE=17
(bootloader) ram: 1024MB Samsung S4 SDRAM DIE=4Gb
(bootloader) cpu: MSM8926
(bootloader) serialno: TA95000QIY
(bootloader) cid: 0xFFFF
(bootloader) channelid: 0xDEAD
(bootloader) uid: 5CEAAC0015000000000000000000
(bootloader) unlocked: Not supported
(bootloader) iswarrantyvoid: Not supported
(bootloader) mot_sst: 8
(bootloader) max-download-size: 536870912
(bootloader) reason: Failed to initialize partition table
(bootloader) imei:
(bootloader) meid:
(bootloader) date:
(bootloader) sku:
(bootloader) iccid:
(bootloader) cust_md5:
(bootloader) max-sparse-size: 268435456
(bootloader) current-time: "Thu Jan 1 7:31:42 UTC 1970"
(bootloader) ro.build.fingerprint[0]: motorola/peregrine_retus/peregrine
(bootloader) ro.build.fingerprint[1]: :4.4.3/KXB21.14-L1.23-4/1:user/rel
(bootloader) ro.build.fingerprint[2]: ease-keys
(bootloader) ro.build.version.full[0]: Blur_Version.21.23.4.peregrine_re
(bootloader) ro.build.version.full[1]: tus.retus.en.US
(bootloader) ro.build.version.qcom[0]: AU_LINUX_ANDROID_LNX.LA.3.5.1_RB1
(bootloader) ro.build.version.qcom[1]: .04.04.02.048.020
(bootloader) version-baseband:
(bootloader) kernel.version[0]: Linux version 3.4.42-gbdf1753-00001-g7a4
(bootloader) kernel.version[1]: 365d ([email protected]) (gcc version 4
(bootloader) kernel.version[2]: .7 (GCC) ) #1 SMP PREEMPT Fri May 23 16:
(bootloader) kernel.version[3]: 38:14 CDT 2014
(bootloader) sdi.git: git=MBM-NG-V41.13-0-gdc5aeaf
(bootloader) sbl1.git: git=MBM-NG-V41.13-0-g683cb0c
(bootloader) rpm.git: git=MBM-NG-V41.13-0-g71b1aae
(bootloader) tz.git: git=MBM-NG-V41.13-0-ga27c415
(bootloader) aboot.git: git=MBM-NG-V41.13-0-g7dc8e78
(bootloader) qe: qe 1/1
(bootloader) ro.carrier: retus
all: listed above
finished. total time: 0.094s
With my limited understanding, it looks like it's stuck somewhere between 4.4.3 and 4.4.4.
Any help/suggestion will be highly appreciated...
Just a guess that "(bootloader) Preflash validation failed" means the bootloader is locked or what your flashing isn't valid so it won't flash it.
the bootloader was unlocked before... but whatever happened, got it locked again. thats part of my problem... i cannot unlock it anymore...
Hey,
I have been using CM11 successfully, but my GPS didn't work and when I tried to fix it by flashing a stock rom my complete phone bricked. I have a GSM phone, but I think I accidentally installed a CDMA rom, but I expect that this would be fixable.
I can access bootloader and recovery. When trying to do a wipe or install TWRP gives the error 'unable to mount '/data'', storage, etc. I then tried to flash a stock rom by the following method: http://forum.xda-developers.com/showthread.php?t=2542219, but I am receiving these errors:
C:\motog\RETAIL-EU_FALCON_KLB20.9-1.10-1.24-1.1_cid7_CFC_1FF_SVC.xml>mfastboot flash partition gpt.bin
target max-sparse-size: 256MB
sending 'partition' (32 KB)...
OKAY [ 0.027s]
writing 'partition'...
(bootloader) Preflash validation failed
FAILED (remote failure)
finished. total time: 0.358s
C:\motog\RETAIL-EU_FALCON_KLB20.9-1.10-1.24-1.1_cid7_CFC_1FF_SVC.xml>mfastboot flash motoboot motoboot.img
target max-sparse-size: 256MB
sending 'motoboot' (1940 KB)...
OKAY [ 0.101s]
writing 'motoboot'...
(bootloader) Motoboot: Preflash validation for tz
(bootloader) Preflash validation failed
FAILED (remote failure)
finished. total time: 0.412s
I also tried to install 4.3, but it gave the same errors. I have googled and I found more people having this problem, but never found a solution.
When I tried to install 4.4 by skipping the first steps it gives the error 'images is too large' and if I do that with 4.3 it seems to install, but does not boot.
'mfastboot getvar all' gives the following information:
(bootloader) version: 0.5
(bootloader) version-bootloader: 4113
(bootloader) product: falcon
(bootloader) secure: yes
(bootloader) hwrev: 0x83C0
(bootloader) radio: 0x1
(bootloader) emmc: 16GB Toshiba REV=06 PRV=01 TYPE=17
(bootloader) ram: 1024MB Hynix S4 SDRAM DIE=4Gb
(bootloader) cpu: MSM8226 CS
(bootloader) serialno: TA8900C7VB
(bootloader) cid: 0x0007
(bootloader) channelid: 0x00
(bootloader) uid: BF2D15020F000000000000000000
(bootloader) unlocked: yes
(bootloader) iswarrantyvoid: yes
(bootloader) mot_sst: 3
(bootloader) max-download-size: 536870912
(bootloader) reason: Reboot mode set to fastboot
(bootloader) imei:
(bootloader) meid:
(bootloader) date:
(bootloader) sku:
(bootloader) iccid:
(bootloader) cust_md5:
(bootloader) max-sparse-size: 268435456
(bootloader) current-time: "Sat Sep 14 7: 3:34 UTC 2024"
(bootloader) ro.build.fingerprint[0]: motorola/falcon_boost/falcon_cdma:
(bootloader) ro.build.fingerprint[1]: 4.4.2/KXB20.9-1.10-1.18-1.1/1:user
(bootloader) ro.build.fingerprint[2]: /release-keys
(bootloader) ro.build.version.full[0]: Blur_Version.175.44.1.falcon_cdma
(bootloader) ro.build.version.full[1]: .Boost.en.US
(bootloader) ro.build.version.qcom[0]: AU_LINUX_ANDROID_JB_3.2.3.04.03.0
(bootloader) ro.build.version.qcom[1]: 0.166.006
(bootloader) version-baseband:
(bootloader) kernel.version[0]: Linux version 3.4.0-gc6fc9e1-00001-gf3bf
(bootloader) kernel.version[1]: 628 ([email protected]) (gcc version 4.
(bootloader) kernel.version[2]: 7 (GCC) ) #1 SMP PREEMPT Thu Mar 13 15:2
(bootloader) kernel.version[3]: 0:21 CDT 2014
(bootloader) sdi.git: git=MBM-NG-V41.13-0-gdc5aeaf
(bootloader) sbl1.git: git=MBM-NG-V41.13-0-g683cb0c
(bootloader) rpm.git: git=MBM-NG-V41.13-0-g71b1aae
(bootloader) tz.git: git=MBM-NG-V41.13-0-ga27c415
(bootloader) aboot.git: git=MBM-NG-V41.13-0-g7dc8e78
(bootloader) qe: qe 1/1
(bootloader) ro.carrier: unknown
all: listed above
finished. total time: 0.070s
I really hope one of you can help me, and if you need more information I will provide that of course.
Edit: As the info says I am on Boost.en.US I also tried to flash 4.4 and 4.3 of that version, but both gave the same errors as above.
Try to flash this or this and post the result:good:
Thank you very very much! I didn't try that one yet. I tried the second one and now it has booted. I am very thankful as I was already looking for a new phone. It didn't give any error at all.
oversleeper said:
Try to flash this or this and post the result:good:
Click to expand...
Click to collapse
bro i m having the same issue with the same device model xt 1033 but it had nougat rom earlier before this mess .
Custom recovery is flashable and usable.
In the custom recovery tge interbal memory shows 0mb as space, i presume that is because of inablity to read or mount partitions right??? i tried to flash lollipop stock rom but always failed at partition gpt.bin file. Showing erroe
Pre flash validation failed.
Whhat to do is their any hope left for my device ???
It has been over 3-4 monthe by now, no solutiob so far !!!
Moto G 1rst Gen US GSM 16 gb.
Following this:
droidviews .com /restore-moto-g-2014-to-stock-and-lock-the-bootloader/
Worked:
mfastboot oem lock begin
mfastboot flash partition gpt.bin
mfastboot flash motoboot motoboot.img
mfastboot flash logo logo.bin
mfastboot flash boot boot.img
mfastboot flash recovery recovery.img
Error:
mfastboot flash system system.img_sparsechunk.0
C:\Users\........\AppData\Local\Android\sdk\platform-tools>mfastboot flash
search system.img_sparsechunk.0
target max-sparse-size: 256MB
sending 'search' (256945 KB)...
OKAY [ 10.071s]
writing 'search'...
(bootloader) Permission denied
FAILED (remote failure)
finished. total time: 10.091s
Any ideas please?
I had TWRP with CM 11 I think M10 on it. Trying to go back to stock because CM is too buggy. I have a Lollypop rom, phone had Kitkat on it before. I have the KK backup but I couldn't update it because of TWRP.
Maybe I have the wrong ROM? I don't know, it i hard to find a working website. This is the filename
XT1034_FALCON-RETUAWS_5.0.2_LXB22.99-36_19_cid9_CFC_1FF.xml.zip
Any help would be greatly appreciated please so I have a working phone again. This is my only phone. Thanks
(bootloader) version: 0.5
(bootloader) version-bootloader: 411A
(bootloader) product: falcon
(bootloader) secure: yes
(bootloader) hwrev: 0x83C0
(bootloader) radio: 0x6
(bootloader) emmc: 16GB Toshiba REV=06 PRV=01 TYPE=17
(bootloader) ram: 1024MB Hynix S4 SDRAM DIE=4Gb
(bootloader) cpu: MSM8226 CS
(bootloader) serialno: TA9190075M
(bootloader) cid: 0x0009
(bootloader) channelid: 0x00
(bootloader) uid: 22FDEE010F000000000000000000
(bootloader) unlocked: yes
(bootloader) iswarrantyvoid: yes
(bootloader) mot_sst: 3
(bootloader) max-download-size: 536870912
(bootloader) reason: Volume down key pressed
(bootloader) imei:
(bootloader) meid:
(bootloader) date:
(bootloader) sku:
(bootloader) iccid:
(bootloader) cust_md5:
(bootloader) max-sparse-size: 268435456
(bootloader) current-time: "Sat Sep 13 22: 4:14 UTC 2014"
(bootloader) ro.build.fingerprint[0]: motorola/falcon_retuaws/falcon_umt
(bootloader) ro.build.fingerprint[1]: s:4.4.4/KXB21.14-L1.61/60:user/rel
(bootloader) ro.build.fingerprint[2]: ease-keys
(bootloader) ro.build.version.full[0]: Blur_Version.210.12.61.falcon_umt
(bootloader) ro.build.version.full[1]: s.AWSRetail.en.US
(bootloader) ro.build.version.qcom[0]: AU_LINUX_ANDROID_LNX.LA.3.5.1_RB1
(bootloader) ro.build.version.qcom[1]: .04.04.02.048.020
(bootloader) version-baseband:
(bootloader) kernel.version[0]: Linux version 3.4.42-gc146877 ([email protected]
(bootloader) kernel.version[1]: ilclbld29) (gcc version 4.7 (GCC) ) #1 S
(bootloader) kernel.version[2]: MP PREEMPT Sat Aug 30 03:25:08 CDT 2014
(bootloader) sdi.git: git=MBM-NG-V41.1A-0-gdc5aeaf
(bootloader) sbl1.git: git=MBM-NG-V41.1A-0-g199f3c5
(bootloader) rpm.git: git=MBM-NG-V41.1A-0-g8b7736e
(bootloader) tz.git: git=MBM-NG-V41.1A-0-g99c1a7c
(bootloader) aboot.git: git=MBM-NG-V41.1A-0-g80481ae
(bootloader) qe: qe 2/1
(bootloader) ro.carrier: unknown
all: listed above
finished. total time: 0.178s
Somehow the word search got in the command removed it and worked thanks.
I'm just about ready to throw the G4 Plus in the bin, but before I do, I thought I'd give it one last chance.
Have been following instructions from https://forum.xda-developers.com/general/rooting-roms/real-official-stock-rom-xt1625-xt1642-t3575895 for example.
fastboot flash recovery recovery.img
(bootloader) slot-count: not found
(bootloader) slot-suffixes: not found
(bootloader) slot-suffixes: not found
(bootloader) has-slot:recovery: not found
target reported max download size of 536870912 bytes
sending 'recovery' (16484 KB)...
OKAY [ 0.563s]
writing 'recovery'...
(bootloader) Invalid partition name recovery
FAILED (remote failure)
finished. total time: 0.576s
So I think the invalid partition name recovery is an issue. Not sure how or why it got deleted, but I see that sku and imei are also set to [0000000000]
fastboot getvar all
(bootloader) slot-count: not found
(bootloader) slot-suffixes: not found
(bootloader) slot-suffixes: not found
(bootloader) version: 0.5
(bootloader) version-bootloader: moto-msm8952-B1.06(*)
(bootloader) product: athene_16mp
(bootloader) board: athene_16mp
(bootloader) secure: yes
(bootloader) hwrev: P2A
(bootloader) radio: 3
(bootloader) storage-type: emmc
(bootloader) emmc: 32GB SAMSUNG RX1BMB RV=08 PV=07 FV=0000000000000007
(bootloader) ram: 3GB SAMSUNG LP3 DIE=6Gb M5=01 M6=05 M7=00 M8=7B
(bootloader) cpu: MSM8952
(bootloader) serialno: 2931de5e
(bootloader) cid: 0x0032
(bootloader) channelid: 0x51
(bootloader) uid: 7AC8590200000000000000000000
(bootloader) securestate: oem_locked
(bootloader) iswarrantyvoid: yes
(bootloader) max-download-size: 536870912
(bootloader) reason: Failed to initialize partition table
(bootloader) imei: 000000000000000
(bootloader) meid:
(bootloader) date: 01-01-1970
(bootloader) sku: 000000000000000
(bootloader) battid:
(bootloader) iccid:
(bootloader) cust_md5:
(bootloader) max-sparse-size: 268435456
(bootloader) current-time:
(bootloader) ro.build.fingerprint:
(bootloader) ro.build.version.full:
(bootloader) ro.build.version.qcom:
(bootloader) version-baseband:
(bootloader) kernel.version:
(bootloader) sbl1.git: sbl1.git
(bootloader) rpm.git: rpm.git
(bootloader) tz.git: tz.git
(bootloader) hyp.git: hyp.git
(bootloader) keymaster.git: keymaster.git
(bootloader) cmnlib.git: cmnlib.git
(bootloader) aboot.git: git=MBM-NG-VB1.06-0-g0edfb0d
(bootloader) qe:
(bootloader) frp-state: no protection (err)
(bootloader) ro.carrier:
all: listed above
finished. total time: 0.175s
I'm sorry I am really a complete noob to Android OS, so I don't fully understand what all this means. I just want to get my phone working again.
Any ideas please?
I've tried RSD Lite and Rescue & Smart Assistant, but neither of these seem to recognize the phone.