What Happens?
My phone weather rebooted from adb, bootmenu, powered off and then on, rebooted from recovery, always boots in bootloader.
It says UTAG "bootmode" configured as fastboot
From bootloader I can go to recovery or regular power up! it all works.
Just I have to face the bootloader every time my phone turns on!
When did this occur?
I don't know, I flashed 3 firmwares back-to-back and then got back to GPe. I booted to bootloader in all ways. I remember me going to bootloader from my XT1033 stock ROM's boot menu, then once using adb reboot bootloader, and once going by pressing VolDown+Power. So I kind of messed up. And then after setting down to a ROM. I rebooted and realised!
What did I try to recover
1. Flashed bootloaders from different firmware
2. Went back to Stock
3. Tried all adb reboot commands
4. Tried all reboot methods from bootmenu
Help Please!
Everything else is working fine, its not a panic attack, but i need a solution
Do "fastboot oem fb_mode_clear"
Enviado desde mi Moto G mediante Tapatalk
Take a backup. And make a full & clean install of stock ROM. Your problem should be solved
I would suggest not to mess with BL , you will get in to trouble
Sent from my XT1032 using Tapatalk
reversegear said:
Take a backup. And make a full & clean install of stock ROM. Your problem should be solved
I would suggest not to mess with BL , you will get in to trouble
Sent from my XT1032 using Tapatalk
Click to expand...
Click to collapse
I have done that more than once!
That doesnt solve the problem! and the prooblem didn't start becaues of BL.
Going to stock doesnt change anything!
Boss442 said:
Do "fastboot oem fb_mode_clear"
Enviado desde mi Moto G mediante Tapatalk
Click to expand...
Click to collapse
That solves the problem!
What is the purpose of fb_mode_set/fb_mode_clear
I would liked to know more!
I asked this question at http://forum.xda-developers.com/showthread.php?t=2738055
But i didnt get a reply there as well!
reversegear said:
Take a backup. And make a full & clean install of stock ROM. Your problem should be solved
I would suggest not to mess with BL , you will get in to trouble
Sent from my XT1032 using Tapatalk
Click to expand...
Click to collapse
Too lazy to not try this:
fastboot oem fb_mode_clear
solved the issue in 1 sec.
help
Hi i already try that fastboot oem fb_mode_clear but still nothing if i turn the phone off as soon as i turn it un it goes back straight to bootloader i have to press normal powerup in order for the phone to boot what else can i do
Bricked MOTO 2 G XT1063 stuck at Bootloader - utag flash fail configured as fastboot
hi mine is XT1063 Bricked, after doing fastboot oem fb mode clear, still i am not able to boot normal.
it says:
boot up failed
failed to validate ftm image
that means its not fih ftm mode
load and validate boot image
failed to validate boot image
Related
Does anyone know the fastboot command to switch the default boot mode back to regular?
slayp00n said:
Does anyone know the fastboot command to switch the default boot mode back to regular?
Click to expand...
Click to collapse
Usually it will boot in fastboot mode if you have a bad flash. What is the message when the phone boots up?
Sent from my XT925 using Tapatalk 2
danifunker said:
Usually it will boot in fastboot mode if you have a bad flash. What is the message when the phone boots up?
Sent from my XT925 using Tapatalk 2
Click to expand...
Click to collapse
stickybit factory_fastboot.
I never had a bad flash. I run cm10.1, but gps was not working someone said flashing stock then reflash cm10.1
So i used that stupid RSD LITE to flahs factory, all i did was fix the xml and erase the recovery flash. It worked fine the phone booted... Then I reflashed cm10.1 which works? Is there an oem command to kill the sticky bit?
I have tha solution!
slayp00n said:
stickybit factory_fastboot.
I never had a bad flash. I run cm10.1, but gps was not working someone said flashing stock then reflash cm10.1
So i used that stupid RSD LITE to flahs factory, all i did was fix the xml and erase the recovery flash. It worked fine the phone booted... Then I reflashed cm10.1 which works? Is there an oem command to kill the sticky bit?
Click to expand...
Click to collapse
excuse me for the next font and style, but I have a lot of time reading post forums and any track that help me to resolve this, and I found!! IN French but, no matter!!
To resolve the message and constantly booting into AP Fastboot, you need (into AP FASTBOOT MODE) put this command in your PC with fastboot
fastboot oem fb_mode_clear
Then press power and voilá... you phone boot normally...
:highfive:
:good::good::good:
alvaro_castro said:
excuse me for the next font and style, but I have a lot of time reading post forums and any track that help me to resolve this, and I found!! IN French but, no matter!!
To resolve the message and constantly booting into AP Fastboot, you need (into AP FASTBOOT MODE) put this command in your PC with fastboot
fastboot oem fb_mode_clear
Then press power and voilá... you phone boot normally...
:highfive:
Click to expand...
Click to collapse
this doesnt fix my issue with boot to bootloader.
atifsh said:
this doesnt fix my issue with boot to bootloader.
Click to expand...
Click to collapse
Well, does your fastboot screen have that message?
If not, what does it say?
killrhythm09 said:
Well, does your fastboot screen have that message?
If not, what does it say?
Click to expand...
Click to collapse
device is locked, status code 0
battery ok
.
.
.
.
,
fastboot reason: flash failure
all i tried was test to boot recovery, not flash,
fastboot boot rec.img
ok so i fastboot flashed stock recovery and it flashed fine and now im no more stuck in bootloader.
and that takes me to my second question/.....
1: can i fastboot flash stock recovery in the first place if im 100% stock, locked and non rooted on the latest kitkat ota
2: can i fastboot flash just the system.img like i flashed recovery and if that is possible hope towelroot will do the work????
Well, first thanks for listening, and please have patience, haha.
I have a Moto G XT1033, my cousin, he tried to unlock the bootloader and the process has not been finalized (I think) because the phone does not turn over, just stood in the LOGO screen.
I tried to reinstall the ROM Stock, but unfortunately I did not succeed
I tried several things and nothing.
I've tried:
1- reinstall the original ROM XT1033 4.4.4
2- install the original ROM XT1033 4.4.2
3- Install the ROM XT1032 4.4.4
4- Install the ROM XT1033 5.0.2
and nothing happened :'( .
so I tried to unlock the Bootloader to see if I could get into recovery mode, to be able to WIPE Cache and Factory. But that was when I discovered that even reinstalling the ROM's and clearing the caches, was not affecting anything on the phone, I was in the Install from SDcard and all folders were there (Whatsapp, PicsArt ...)
I can not install Custom Recovery and not install any ROM since it is not installing anything !!!
and when I Wipe cache it restarts on its own and does not delete anything!
I am Brazilian and I used Google translator to write this text, I hope to help me! Thank you for listening! <3
I have a Moto G XT1032 with unlocked bootloader, custom recovery TWRP and android 5.0.2 via adb, no problem
Can you boot into fastboot? Does it say the bootloader is unlocked?
So you are able to flash a stock ROM without errors?
Can you get into stock recovery to wipe?
audit13 said:
Can you boot into fastboot? Does it say the bootloader is unlocked?
So you are able to flash a stock ROM without errors?
Can you get into stock recovery to wipe?
Click to expand...
Click to collapse
Yes, but nothing works, the adb process of all "Okay" but when rebooting, it is only on screen logo and does not start, and after about 2 minutes it restarts again.
audit13 said:
Can you boot into fastboot? Does it say the bootloader is unlocked?
So you are able to flash a stock ROM without errors?
Can you get into stock recovery to wipe?
Click to expand...
Click to collapse
You can boot into fastboot? - Yes said the bootloader is unlocked? - yes
So you are able to flash a ROM stock without errors? - Yes and no XD (in adb shows that installs but does not actually install anything)
You can get in stock recovery to clean? yes and no (the screen shows that wiped but not actually cleaned anything, the fiction folders all there in the same place, whatsapp etc ...)
You are using ADB or fastboot to flash stock ROM? Fastboot commands only work when the phone is in fastboot mode.
audit13 said:
You are using ADB or fastboot to flash stock ROM? Fastboot commands only work when the phone is in fastboot mode.
Click to expand...
Click to collapse
good, I do not know a lot of things, but change ROM's and those kinds of things I can do, you see, is that what's going on I've never seen, practically the cell turned into a zombie, he's dead just not hahaha.
I'm using the ADB and Fastboot the in the same folder, and installed the ROM's in fastboot mode (vol - + Power)
it's OKAY in the installation process, only it does not actually install anything.
already tried deleting the cache but he n erases anything already gave factory reset and nothing happens: '(
researched two days and a half on the subject to try to solve it, but I was out of options, so I posted here in the forum, takes a lot to help me with this!
in the process with my phone got everything worked unlock the good bootloader, install custom recovery and rom lollipop
since my cousin was not so lucky
he screwed the phone in bootloader unlocking process (if I'm not mistaken)
Hello, I'm facing a strange issue.
I just wanted to restore my device (unlocked, rooted, stock rom) to stock, to reroot etc
flashed everything in fastboot mode as usual.
but after I flashed everything, and everytime I boot my device, it goes stright to bootloader, with a diferent message
AP FASTBOOT FLASH MODE (SECURE)
BL :80.CB (SOME NUMBERS)
BASEBAND: NOT FOUND
SERIAOL NUMBER...
...
CONSOLE [NULL] : NULL
Click to expand...
Click to collapse
I tried reflashing everything, but this message keep showing up when the device is booted.
PS: when I hit start on bootloader, it boots normaly...
anyone has faced this or something relatred? thank you folks
Do a factory reset(not from The recovery, do that in the bootloader selecting an option called "factory")
Enviado desde mi Moto G mediante Tapatalk
I have unlocked my bootloader. Every time I power on my Motorola Moto G3, it boots into the recovery screen. It isn't really a problem, it's more of an annoyance. I have to use the power / volume buttons to choose start and then it boots into the OS fine.
Any help would be greatly appreciated, thanks.
ItsWoffles said:
I have unlocked my bootloader. Every time I power on my Motorola Moto G3, it boots into the recovery screen. It isn't really a problem, it's more of an annoyance. I have to use the power / volume buttons to choose start and then it boots into the OS fine.
Any help would be greatly appreciated, thanks.
Click to expand...
Click to collapse
Look at this thread
https://forum.xda-developers.com/2015-moto-g/help/reboot-bootloader-mode-t3653547
melp57 said:
Look at this thread
https://forum.xda-developers.com/2015-moto-g/help/reboot-bootloader-mode-t3653547
Click to expand...
Click to collapse
Do I need to type in fastboot oem fb_mode_clear while re flashing stock firmware again like I would to relock the bootloader?
ItsWoffles said:
Do I need to type in fastboot oem fb_mode_clear while re flashing stock firmware again like I would to relock the bootloader?
Click to expand...
Click to collapse
Actually it's not an issue, the command
Code:
fastboot oem fb_mode_set
makes the phone boot into bootloader mode instead of starting android. To undo this, you'll just have to type in-
Code:
fastboot oem fb_mode_clear
. No need to flash the whole firmware again if this is the only problem.
Broadcasted from Zeta Reticuli
Gravemind2015 said:
Actually it's not an issue, the command
Code:
fastboot oem fb_mode_set
makes the phone boot into bootloader mode instead of starting android. To undo this, you'll just have to type in-
Code:
fastboot oem fb_mode_clear
. No need to flash the whole firmware again if this is the only problem.
Broadcasted from Zeta Reticuli
Click to expand...
Click to collapse
Where do I type this command in? Using ABD and fastboot? Do I just go into the bootloader and plug my phone into my PC, then open up ABD and fastboot and type in that command or what do I do? Is that the only command I need to type in? Sorry, I'm a noob to this kinda stuff!
ItsWoffles said:
Where do I type this command in? Using ABD and fastboot? Do I just go into the bootloader and plug my phone into my PC, then open up ABD and fastboot and type in that command or what do I do? Is that the only command I need to type in? Sorry, I'm a noob to this kinda stuff!
Click to expand...
Click to collapse
Reboot the phone into bootloader mode. To do this, power off the phone, press and hold power+volume down button till it shows up.
Plug the phone into PC, open command prompt from the folder where adb.exe and fastboot.exe are present, and type that command (only that one is needed). Disconnect the phone and try rebooting to see if it boots correctly.
Broadcasted from Zeta Reticuli
ItsWoffles said:
I have unlocked my bootloader. Every time I power on my Motorola Moto G3, it boots into the recovery screen. It isn't really a problem, it's more of an annoyance. I have to use the power / volume buttons to choose start and then it boots into the OS fine.
Any help would be greatly appreciated, thanks.
Click to expand...
Click to collapse
I think u flashed recovery to boot..
mg_jishad said:
I think u flashed recovery to boot..
Click to expand...
Click to collapse
If that was the case, you could never boot the phone into Android... the OP stated that he can select continue and start the device normally. It is most likely stuck in fastboot fb_mode like @Gravemind2015 stated.
Excuse any possible miss posting of My question.
Moto G 3 factory rom and rooted
Problem: Motorola security update action causes Moto to keep booting into twrp recovery loop.
Have tried to break the looping, but there is something I am missing or not doing correctly any help thanks.....
Uncle Waldo said:
Excuse any possible miss posting of My question.
Moto G 3 factory rom and rooted
Problem: Motorola security update action causes Moto to keep booting into twrp recovery loop.
Have tried to break the looping, but there is something I am missing or not doing correctly any help thanks.....
Click to expand...
Click to collapse
Now this sounds like you flashed TWRP in your boot image... Reflash the stock boot image with fastboot
acejavelin said:
Now this sounds like you flashed TWRP in your boot image... Reflash the stock boot image with fastboot
Click to expand...
Click to collapse
Shouldn't that make the phone stay at bootlogo as the kernel and ramdisk are overwritten by TWRP code? @Uncle Waldo stated that the phone is looping into TWRP after *moto update action*. So what I am able to figure out is that this is a OTA-on-stock-rom-with-custom-recovery situation. I am a litte doubtful though as google says the phone boots into kernel from recovery (which is evident here) instead of kernel from boot partiton (source), so you may be 100% correct here too
@Uncle Waldo : If that is indeed the case (i.e moto issued an update and since rebooting the phone it's just looping into TWRP and giving an error) then I'd recommend that-
Flash stock boot.img as @acejavelin suggested
Flash stock recovery.img (as TWRP can't nstall stock ROM updates)
This is assuming that the /system partition was never modified in any way. If the update still fails in stock revovery, I'd guess that the whole system has to be restored to a non-modified state (i.e flashing the full firmware). You can try flashing all without doing the 'fastboot erase' part though, but i'd recommend you to backup your files using TWRP when you can.
links-
Link to the flashing guide is here
Link to the firmware index is here
command to install recovery -
Code:
fastboot flash recovery recovery.img
command to flash boot.img-
Code:
fastboot flash boot boot.img
Uncle Waldo said:
Excuse any possible miss posting of My question.
Moto G 3 factory rom and rooted
Problem: Motorola security update action causes Moto to keep booting into twrp recovery loop.
Have tried to break the looping, but there is something I am missing or not doing correctly any help thanks.....
Click to expand...
Click to collapse
If it is because of an update, you can't accept it while on TWRP... If you did, try to access the TWRP menu and if you can't boot TWRP from.fadtboot (not flash) and wipe caches... It should boot normally after that.
ACE; moto has been operating for sometime now fine
acejavelin said:
Now this sounds like you flashed TWRP in your boot image... Reflash the stock boot image with fastboot
Click to expand...
Click to collapse
You believe this could be my problem as the moto boots just fine and it's only started this problem when I installed the following update.
Motorola > android security updates version 24.211.14.en.US
After this install and reboot it appears to work just fine and then shortly reboots into TWRP from here the only correcting action that stops the reboot loop is "RESTORE".
After restoring and reboot the moto is back to operating as before and at some point I get the same message to install the security updates and the dance begins anew.
If reflashing the stock boot image via fastboot could correct my problem > then I am all ears Ace, as it's been sometime since I ventured into android ville and any help in this matter thanks...
Uncle Waldo said:
You believe this could be my problem as the moto boots just fine and it's only started this problem when I installed the following update.
Motorola > android security updates version 24.211.14.en.US
After this install and reboot it appears to work just fine and then shortly reboots into TWRP from here the only correcting action that stops the reboot loop is "RESTORE".
After restoring and reboot the moto is back to operating as before and at some point I get the same message to install the security updates and the dance begins anew.
If reflashing the stock boot image via fastboot could correct my problem > then I am all ears Ace, as it's been sometime since I ventured into android ville and any help in this matter thanks...
Click to expand...
Click to collapse
You edited the original question after I replied... Read my follow-up answer. You can't take an OTA with TWRP installed, just start TWRP and wipe caches and then don't accept any further OTA.
Ace; I missed that one
acejavelin said:
You edited the original question after I replied... Read my follow-up answer. You can't take an OTA with TWRP installed, just start TWRP and wipe caches and then don't accept any further OTA.
Click to expand...
Click to collapse
Your correct I missed that one, a BC moment (before coffee) sorry.
Okay in the fog of my memory I do now remember the OTA prohibition as I said it's been a piece of time.
I've done as instructed and all is well again, but will this nag screen appear again as it has done.
Question > How do I shut the motorolia OTA update off, so I don't get their stupid never ending nag screen everytime that I look at phone?
Thanks for your help...
---------- Post added at 05:13 PM ---------- Previous post was at 04:33 PM ----------
Ace I figured it out thanks for all your help...
i had the problem, when the cell, automatic restarted and it stuck on this screens, but it never came back, i already tried flashing the cellphone, and i already tried adding a custom bootloader, but no luck, it gave me the information that it mismatch, and attempts to enter the bootloader, without luck, i also already tried to only boot with fastboot, and no luck, it stucks on the twrp or m screen or shows different issues like screen fading or rumbling without reason, attempted to enter the recovery and only got to normal recovery from android, attempted to sideload the zip, and got a verification error, and it fails, again, i cant install a custom recovery, it always fails, and i dont know what to do... i really need help, any suggestion?? i already searched and didnt found any tools, flasher tool v.2 not found, and other tools are not able to help as well, help!!
edit, forgot to add, its an moto g. 2013 , xt1032 ANDROID LOLLIPOP
x-fighter said:
i had the problem, when the cell, automatic restarted and it stuck on this screens, but it never came back, i already tried flashing the cellphone, and i already tried adding a custom bootloader, but no luck, it gave me the information that it mismatch, and attempts to enter the bootloader, without luck, i also already tried to only boot with fastboot, and no luck, it stucks on the twrp or m screen or shows different issues like screen fading or rumbling without reason, attempted to enter the recovery and only got to normal recovery from android, attempted to sideload the zip, and got a verification error, and it fails, again, i cant install a custom recovery, it always fails, and i dont know what to do... i really need help, any suggestion?? i already searched and didnt found any tools, flasher tool v.2 not found, and other tools are not able to help as well, help!!
edit, forgot to add, its an moto g. 2013 , xt1032 ANDROID LOLLIPOP
Click to expand...
Click to collapse
which bootloader?
locked?
which firmware?
flashed how?
Sent from my PH-1 using XDA Labs
sd_shadow said:
which bootloader?
locked?
which firmware?
flashed how?
Sent from my PH-1 using XDA Labs
Click to expand...
Click to collapse
i am unable to use other than the normal bootloader, htt p://cdn.droidviews.com/wp-content/uploads/2014/02/moto-g-bootloader-mode.jpg but mine says unlocked code 3, i used fastboot to attempted to flash the phone, and nothing changed. it has the stock firmware lollipop 5.0.2, codename falcon, i flashed it with fastboot, but no luck, attempted to added by sideload on the android recovery default, and it gives me the errorhttp s://i.imgur.com/nSFMea9.jpg and i am unable to add any file, it doesnt has external sd
x-fighter said:
i am unable to use other than the normal bootloader, htt p://cdn.droidviews.com/wp-content/uploads/2014/02/moto-g-bootloader-mode.jpg but mine says unlocked code 3, i used fastboot to attempted to flash the phone, and nothing changed. it has the stock firmware lollipop 5.0.2, codename falcon, i flashed it with fastboot, but no luck, attempted to added by sideload on the android recovery default, and it gives me the errorhttp s://i.imgur.com/nSFMea9.jpg and i am unable to add any file, it doesnt has external sd
Click to expand...
Click to collapse
https://m.imgur.com/nSFMea9
http://cdn.droidviews.com/wp-content/uploads/2014/02/moto-g-bootloader-mode.jpg
Sent from my PH-1 using XDA Labs
---------- Post added at 01:48 PM ---------- Previous post was at 01:47 PM ----------
neither one of those says what files you are trying to flash
Sent from my PH-1 using XDA Labs
attached
Sent from my PH-1 using XDA Labs
x-fighter said:
i am unable to use other than the normal bootloader, htt p://cdn.droidviews.com/wp-content/uploads/2014/02/moto-g-bootloader-mode.jpg but mine says unlocked code 3, i used fastboot to attempted to flash the phone, and nothing changed. it has the stock firmware lollipop 5.0.2, codename falcon, i flashed it with fastboot, but no luck, attempted to added by sideload on the android recovery default, and it gives me the errorhttp s://i.imgur.com/nSFMea9.jpg and i am unable to add any file, it doesnt has external sd
Click to expand...
Click to collapse
From the picture you uploaded, says that your bootloader is locked, so that is why you can't flash any custom recovery. First you need to unlock your bootloader first but BACKUP FIRST, cause it will erase your internal storage when you unlock your bootloader. After unlocked, then you can flash custom recovery. Hope that helps.
Edit: but if your bootloader is really already unlocked, than try this, flashed twrp, then power down your phone by pressing the power button, then boot to twrp by press power button + volume down buttom. Don't reboot to twrp using the option im bootloader mode or using adb.
tepar said:
From the picture you uploaded, says that your bootloader is locked, so that is why you can't flash any custom recovery. First you need to unlock your bootloader first but BACKUP FIRST, cause it will erase your internal storage when you unlock your bootloader. After unlocked, then you can flash custom recovery. Hope that helps.
Edit: but if your bootloader is really already unlocked, than try this, flashed twrp, then power down your phone by pressing the power button, then boot to twrp by press power button + volume down buttom. Don't reboot to twrp using the option im bootloader mode or using adb.
Click to expand...
Click to collapse
i will upload a more reccent one, where i already unlocked it, but i will try whaat you edited, thank you!! let me try and post results