Related
This is a new thread for the star n9770 mt6577 Dual core.
ROOT
I have just used this method to safely root my star n9770 and worked perfect,it just wipes your time and date after root so just reset them and that's it.
you must follow instructions....
http://colonelzap.blogspot.co.uk/search?q=n9770
Thank you Rumpelstilzchen for that!
(does not seem to work with new 13/07 firmware but fine with earlier)do not try on devices running firmware later than 13/07/12 it will naff them
FIRMWARE STAR N9770 DUAL CORE MT6577/ulefone N9770.
STAR N9770 DUAL CORE MT6577/ulefone N9770.
CUSTOM RECOVERY
https://rapidshare.com/files/4163487113/STAR-N9770_Custom_Recovery.zip
CWM
https://rapidshare.com/files/3326837023/CWM-SuperSU-v0.93_tirannozaurus.zip
FLASHTOOLS AND DRIVERS
https://rapidshare.com/files/3354053184/FlashTools_driver.rar
FIRMWARE 13/07/2012 Thanks kylie 1965
https://rapidshare.com/files/2757089569/20120713_e1809c_v77_gq1008_9p017.N9770.zip
STOCK FIRMWARE 4.0.9
I have received this today from my supplier of device n9770 dual core
https://rapidshare.com/files/2825524946/欧乐风N9770-2012-0712.zip
http://www.mediafire.com/?eyci9chr527chu9 10/08/2012 latest for devices running 5647 firmware only
latest firmware N9770-20120725_e1809 c_v77_gq1008_5647.zip 25/07/2012
Will fix back camera issues due to additional sensors in device.
http://www.mediafire.com/?2fcalamvy7hvlyo
HOPE THESE HELP.
THIS IS ORIGINAL FIRMWARE FROM FIRST ISSUE AND IS OLD AS ARE THE ROOT EXPLOIT AS WAS FOR FIRST N9770 MADE.
NOW THERE ARE MANY MODELS CALLED N9770 SO PLEASE READ THREAD FOR MORE UPDATED FIRMWARE AND EXPLOITS ROOT ETC. ENSURE YOU MAKE A NOTE OF YOUR DEVICE FIRMWARE IN SETTING /ABOUT PHONE AND WRITE IT DOWN BEFORE YOU START FLASHING THE FIRST FIRMWARE YOU FIND.
ALWAYS BACKUP DEVICE
Thank you !
Do you know whats the differences between the both firmwares in your post are ?
My N9770 will not fall into Deep Sleep. It just clock the CPU down to 250mhz, but its still on and drains the battery within 12 hours.
I tried several ROMs i've found but all the same. Maybe your stock firmware solves the problem.
hardi75 said:
Thank you !
Do you know whats the differences between the both firmwares in your post are ?
My N9770 will not fall into Deep Sleep. It just clock the CPU down to 250mhz, but its still on and drains the battery within 12 hours.
I tried several ROMs i've found but all the same. Maybe your stock firmware solves the problem.
Click to expand...
Click to collapse
i have no idea but i have tried to install the stock firmware i got today but it wont happen,and flashed with the other firmware i got from kylie and its not good.
if you have any working roms i would seriously appreciate a link to some roms as my colours are washed out with the kylie firmware and stock need to be done in recovery but can not do it as wont have saying not signed?so i need a little help
ref battery you need to root and then set cpu to ondemand i use no frills cpu from play to do this
managed to sort out colour issue flashed with mdt and changed the grapics driver so the colour is good now but i have the problem that i started with which created all this hassle and that is the cameras...How do i swap from the front to back camera???
i dont have the little icon to change cameras.
sas007 said:
i have no idea but i have tried to install the stock firmware i got today but it wont happen,and flashed with the other firmware i got from kylie and its not good.
if you have any working roms i would seriously appreciate a link to some roms as my colours are washed out with the kylie firmware and stock need to be done in recovery but can not do it as wont have saying not signed?so i need a little help
ref battery you need to root and then set cpu to ondemand i use no frills cpu from play to do this
Click to expand...
Click to collapse
I tried out this Taiwan101 ROM, this one from a russian forum (25/07?) and this one from a chinese forum (newer Taiwan?).
I also had the issue with these strange colors, its the wrong display driver. I fixed it with SP_MDT by selecting RX_50NT_401B as display driver. It seems that these ROMs had all RX_50NT_365A as default which end up in wrong colors.
With the 25/07 Firmware i also killed my cameras, should also be fixable with the correct drivers.
This 'not signed' error appears also with custom recovery ?
yep i can not get the back camera to work/switch, going to try your later rom is it rooted?
How do i install these roms?the later newer Taiwan as i am not used to dual core,do you copy zip to sd card (internal) and go to recovery and update via sd card?
and how would you change the display driver if not flashing via tools
Did you ever have the cameras working as they should?
100 questions.......
hope we can get there in the end
sas007 said:
How do i install these roms?the later newer Taiwan as i am not used to dual core,do you copy zip to sd card (internal) and go to recovery and update via sd card?
Click to expand...
Click to collapse
Yes exactly, you had to copy the file to the sd card and flash it via recovery. But you had to install a custom recovery first (i flashed only the recovery. Flashing also the boot.img and the preloader out of this zip ended with a not booting phone.
sas007 said:
and how would you change the display driver if not flashing via tools
Click to expand...
Click to collapse
I flashed the driver with tools. Not the hole ROM, just the uboot.bin. It seems that sp_mdt saves the driver in uboot when you close the programm. I did so and flashed the uboot with the 'normal' flashtool.
sas007 said:
Did you ever have the cameras working as they should?
Click to expand...
Click to collapse
Both cameras survived every change of firmware until i flashed the 25/7 ROM.
It seems that there are several hardware version. With the Taiwan101 firmwares the external sd card will not be recognized. I flashed the boot.img from the 13/07 firmware and the sd card came back. SD card is also out of function with your stock rom.
I still had the problem with phone not going into deep sleep. Also NoFrills couldn't change that. Maybe i've not found the right ROM for my hardware yet. I got it from CECT.
Hi i have flashed with the firmware from kylie and changed the display driver whilst flashing with mdt..display is good
I do not have back camera i see no way to switch to back but the front works fine and i have no idea as when i flashed with default driver it was the same no back camera
I do have external SD no problem with 32gb
I had no problems with imei
i need a recovery to flash
found these
http://translate.google.com/transla...um.china-iphone.ru/viewtopic.php?f=70&t=21147
http://translate.google.com/transla...um.china-iphone.ru/viewtopic.php?f=70&t=21147
but no help to me
The root tutorial posted here does not work with new firmware,so i copied recovery image from custom recovery (brunos)and replaced recovery in new firmware and flashed using mdt with the driver change for graphics..it worked and installed custom recovery and i then proceeded to root with the cwm-su zip in recovery and it worked.
but still no back camera
Cameras and display are working now with these drivers selected in sp_mdt :
mt9p017_raw hi704_yuv RX_50NT_401B
Which display driver have you choosen ? The same ?
hardi75 said:
Cameras and display are working now with these drivers selected in sp_mdt :
mt9p017_raw hi704_yuv RX_50NT_401B
Which display driver have you choosen ? The same ?
Click to expand...
Click to collapse
yes i used the same settings but still no back camera and other non stock camera apps will not work
i am uploading the modified firmware with these settings in the uboot and with the custom recovery in so can be straight flashed in one go.
sas007 said:
yes i used the same settings but still no back camera and other non stock camera apps will not work
i am uploading the modified firmware with these settings in the uboot and with the custom recovery in so can be straight flashed in one go.
Click to expand...
Click to collapse
You have tested all possible drivers ? Did the second camera work befor flashing ?
I changed the driver and bootet into system test (power+vol. down) to see if the cams are back or not. Its a bit faster than waiting for android to boot completely.
hardi75 said:
you have tested all possible drivers ? Did the second camera work befor flashing ?
I changed the driver and bootet into system test (power+vol. Down) to see if the cams are back or not. Its a bit faster than waiting for android to boot completely.
Click to expand...
Click to collapse
hi ran the test and main camera is fail...great back it goes
sas007 said:
hi ran the test and main camera is fail...great back it goes
Click to expand...
Click to collapse
Maybe I could try note firmware. I have used same settings for drivers with the same firmware as you but the main camera still dead. Strange.
how do you get the stock firmware signed,i wish i could use it as may hold the key
Sent from my ONDA MID using xda premium
N9770 topic
sas007 said:
I have used same settings for drivers with the same firmware as you but the main camera still dead. Strange.
how do you get the stock firmware signed,i wish i could use it as may hold the key
Click to expand...
Click to collapse
I've not used the 13/07 version u posted, i got it from this link. Should be se same but who knows. Maybe released
You have flashed the custom recovery which you have posted on the first page ? I got these not signed errors only with stock recovery.
hardi75 said:
I've not used the 13/07 version u posted, i got it from this link. Should be se same but who knows. Maybe released
You have flashed the custom recovery which you have posted on the first page ? I got these not signed errors only with stock recovery.
Click to expand...
Click to collapse
Hi used your firmware link outcome the same no camera so i flashed taiwans rom still no back camera,used uboot from n8000 has the correct drivers for cameras but not display...uboot from i9220 has wrong drivers as has the uboot from note.
used the firmware sent to me by supplier renamed it update zip and installed over taiwans rom and still no back camera.
was getting error "can not connect to camera" several times through out the process,have called it a day and am returning device..
Repartition N9770
Has anyone come out with the 2.5g repartition yet??
Try clearing your cache and removing your battery. Then, install any free basic new Jellybean cam app from the market. See if that re-installs your camera.
sas007 said:
Hi used your firmware link outcome the same no camera so i flashed taiwans rom still no back camera,used uboot from n8000 has the correct drivers for cameras but not display...uboot from i9220 has wrong drivers as has the uboot from note.
used the firmware sent to me by supplier renamed it update zip and installed over taiwans rom and still no back camera.
was getting error "can not connect to camera" several times through out the process,have called it a day and am returning device..
Click to expand...
Click to collapse
ronbo76 said:
Try clearing your cache and removing your battery. Then, install any free basic new Jellybean cam app from the market. See if that re-installs your camera.
Click to expand...
Click to collapse
Hi and thanks for your suggestion i had already tried that with 3-4 different apps,all stated they could not connect to camera,for me it is a hardware fault as i have done everything humanly possible to resolve.i have now returned device and await a new one.
having talked with china supplier the n9770 has a lot of problems and was released to market to early..most of the models sent out have been recalled due to major faults and they said it wont be until middle of September before the chipset mt6577 is back,whether there is any truth in that i do not know..but they had no replacement for me and have already issued a full refund and postage costs on emailing proof of postage so they seem honest....ummm
Cheers
Hey gang, I got this Flytouch 8 tablet last week, model number is BC1003, android version 4.0.4, baseband version 1.5rc4, kernel version 3.0.8+ [email protected] #68 Sat Dec 8 08:54:36 CST 2012, build number crane_bc1003-eng 4.0.4 IMM76D 20121217 test-keys.
I've tried several options to load the recovery partition, only way I can access the recovery is through the backup and reset menu in settings, if I try to do it with the device powered off and holding the menu and power it just boots normal. I've tried a number of options home+power, vol up or down + home, none work. When I do get into the recovery, I cannot scroll through the options only thing there is the android robot with a red triangle and an exclamtion point.
Recovery version says android system recovery 3e EVB-V13.
I also cant get the sd card to mount. I've tried refromatting it with fat32, fat16, ext3 ext4. everything I get a message saying sd card damaged. I've tried 3 different card and same thing.
Any ideas XDA friends? I would like to put a custom rom like AOSP or CM9 or CM10 on it and clockwork recovery if that is an option. I've searched the net high and low for roms, I find many for other Flytouch tablets, but not Flytouch 8. This is the allwinner A10 processor in this one.
Thanks for your help friends.
I
Same problem her with a rooted FT 8 (same as yours)
.
After reboot i get sd card damage error.. after give this da RW i can mount this card again in settings/ storage.
After a reboot i get alway the error sd card damage....
I can get CWM 6.02 on this flytouch but didn`t get any custum roms or CWM backup installed...so get back tio basic image file with Livesuite.
have same recovery : recovery 3e EVB-V13 but cannot do anything with it. It don`t react with all the combination button on my flytouch.
Hopefully you can?
Same problem her with my fluytouch 8 32GB any halp pleas.
Recovery menu
hi
I've got the same tablet from china, am stuck at same spot as you are all, but I figured out how to move through menu in recovery, use usb mouse or keyboard.... any news on some custom rom and installation on this lousy tablet would be appreciated......
Solved Recovery Issue.
Hey everyone. I found this thread today, I tried it and it works perfectly. http://forum.xda-developers.com/showthread.php?t=2189640
I also read somewhere that Allwinner A10 and A13 cannot be flashed using stock recovery, you must use a program like Livesuit to flash firmwares. You can flash custom roms using CWM once it's installed on your device.
fldave612 said:
Hey everyone. I found this thread today, I tried it and it works perfectly. http://forum.xda-developers.com/showthread.php?t=2189640
I also read somewhere that Allwinner A10 and A13 cannot be flashed using stock recovery, you must use a program like Livesuit to flash firmwares. You can flash custom roms using CWM once it's installed on your device.
Click to expand...
Click to collapse
thanks man, this is good news, first step forward in cracking this damn slow tablet....now we need decent rom to install, any ideas?
Possible bricked BC1003..
Hi there I've got the exact same tablet with you BC1003 Model Flytouch Allwinner A10 Superpad 8 1GB Ram version running Android 4.0.4 stock.
So after following guides and researching a lot I ended up trying to upgrade to Jelly Bean.
I got CWM 6.02 installed fine. So I started the flash process.
Firstly I backed up my stuff and then I did a wipe data / factory reset.
Then proceeded and installed the latest possible rom version which I found to be : AOKP JB 4.1.2 ALLWINNER A10.zip
So I installed that one and the process went fine.
Then I installed this compatibility pack : t05a-v3_compatibility_1.2.0.zip
It also went fine.
Then I installed this google apps pack : gapps-jb-20120726-signed.zip
And it also installed normally.
So I was ready to reboot my tablet and so I did.
It turned off and then on again and here we are :
I now notice the screen turn on but it never shows anything..
Before flashing it it would turn on and show the Android OEM screen, then show the android loading text and then turn off and on and show the locked screen which I had to unlock and enter my desktop.
I notice that the screen light follows that pattern so the system is running normally only I don't get to actually see anything on it.
Now I'm kinda stuck here.. I've installed LiveSuite but when I try to install the recovery.img I have from my backup it says invalid image..
Have I bricked it or is there a way out of this mess?
Actually it's not entirely bricked.. well I finally got it to work with LiveSuit 1.09 and managed to flash its firmware to a couple more roms.
1. sun4i_crane_t05a_20120409.img -> Ends up showing some messy stuff on the screen. Looks like the resolution is not correct.
2. sun4i_crane_futekoA90universal_20120531.img -> Shows lots of white stuff and colors switching jelly-like.. But still it doesn't work.
3. TAB360-364_Android_411_Jelly_Bean.img -> This is the official A10 Jelly Bean firmware for Yarvik TAB364 GoTab Gravity 8".. No wonder I still got back to the blank screen issue. I only notice the back light turn on and off following the pattern of normal functionality, only I'm not able to actually see it..
Well, at least I'm still able to keep flashing roms to it.. Any ideas?
I can't even find my stock rom to turn back to 4.0.4. Where exactly is it located in my recovery-mode backup?
Btw, in case it plays any part my tablet is 10.2''.
Any help would be greatly appreciated.
EDIT : Finally I figured it out! My correct stock rom is : sun4i_crane_bc1003.img
I found it through google and after flashing to it I managed to get my tablet at a working state. (ICS 4.0.4 ICS 4.0.3)
So, I'll now try to use more Jelly Bean roms without worrying about bricking it.
Oh, something I noticed that might help others too.. even though on the packaging it says Flytouch Superpad 8 Allwinner A10 this tablet model (BC1003) is actually the Flytouch Superpad 7 and that helped me find my correct rom. Keep that in mind from now on. I'll keep you updated if I succeed in booting to Jelly Bean.
Finally some success..
Well, I finally have some interesting updates on the subject.
I managed to get Jelly Bean to work (Versions 4.1.2 and 4.1.1) on my BC1003 tablet without a compatibility pack (still none has worked for me).
Details on 4.1.2 Version :
Rom File Name : AOKP-4.1.2-3.0.52-Revb.zip
System running smoothly with wifi working fine.
Sound is fine and no crashes occurred.
Touchscreen, screen rotation and camera do not work.
I noticed that I can't browse to my external sd card.. it doesn't seem to get mounted.
Details on 4.1.1 Version :
Rom File Name : cm10_a10_20120913.zip
System running extremely smooth with wifi working fine.
Sound is fine and I experienced no crashes.
Touchscreen, screen rotation and camera do not work.
Also could not mount my external sd card.
Important bug noticed : When I try to change the brightness of my tablet's screen it enters suspended mode no matter what I do and is not fixable. I had to reflash the rom to recover from that state.
I think most of the problems would go away if I found a compatible jelly bean compatibility pack for this tablet.
If anyone has any clue please let me know.
So far I've tried these with no luck :
t05a-v3_compatibility_1.2.0.zip
t05a-unk_compatibility_1.2.0.zip
907c_compatibility_1.2.0.zip
By the way the BC1003 ICS rom that I found to be working was actually not my manufacturer's and it was version 4.0.3 instead of 4.0.4 that my original one was.
So, @fldave612 if it's possible could you please backup and upload yours somewhere so that I can also have it?
EDIT: Actually I figured out that I had kept a good backup form my ICS 4.0.4 using clockwork backup/restore and switched back to that for now.
But I've kept a backup of my Jelly Bean installation too so it's very easy to switch to that now. I'll try again once we get a compatibility pack working.
I feel we're very close to completely upgrading to Jelly Bean now on this tablet. We only need a working compatibility pack.
How did you succeed to install these ROMs, I tried both, installation went OK, but after reboot, only black screen......
Sent from my GT-P5110 using xda app-developers app
baschelik said:
How did you succeed to install these ROMs, I tried both, installation went OK, but after reboot, only black screen......
Sent from my GT-P5110 using xda app-developers app
Click to expand...
Click to collapse
I just installed them without a compatibility pack. It's not the jelly bean build that fails.. it's just the compatibility pack.
I researched it a bit and starting to look for a compatibility pack that works on very similar tablets (10.2'' - 1024 x 600 - 1GB Ram).
I found some, and got it to boot without a blank screen. Some showed messy colors others seemed to be working fine but still no touch..
So until we get one working on our specific precious tablet, we're kinda stuck here..
The 4.1.2 version seemed to be working fine but without touchscreen it's pretty much useless.
We could live without a camera or screen rotation, but not without touchscreen..
I even figured out that I could browse to the external sd card by going to root and then storage folder.. instead of mnt..
Actually now I'm stuck with ICS 4.0.3 since the original backup I kept proved to not be working fine.. it kept on crashing all the time..
So if someone has the original BC1003 ICS 4.0.4 that came from the manufacturer please upload it somewhere and post a link here.
Also if someone works on it to create a touchscreen driver for the world would become more beautiful..
Go to this link: http://www.maixin-china.com/software-download.asp Scroll down about half way and go to the link for "MaPan F10B (Cortex A8 Flytouch 6 and Flytouch 8) Software". I used the newest one 11-28.
This is a firmware is the one for this tablet. Use Livesuit to flash it, it will restore the tablet back to 4.0.4 factory.
It is virtually impossible to brick an A10 tablet from what I'm reading because it can be flashed via usb and have to boot loader re-imaged.
This link is very helpful to flash via Livesuit: http://elinux.org/Hack_A10_devices
Hope this helps you all as much as it did for me. Hopefully in the near future some developers will build a CM10 or higher version that will work on this tablet, until then I'll use this rom with Clockwork recovery mod.
Moin @all
Ich have chrashed my tab too but the download link is dead.
Any ideas where ich can load the file ?
Sorry for my ****ty bad English :silly:
Gothfather
I've also got this tablet (BC1003) - thank you for all the useful information posted on this thread so far.
If I've understood correctly, it's possible to install custom firmware using LiveSuite but at the moment none of them fully support this tablet - is that right?
At the very least I'm looking for a way to increase the size of the internal memory partition - the stock partition table has this unnecessary virtual sdcard partition taking most of the 2GB internal memory...
i have one of these damn slow tablets
i watched a vid on youtube about how to remove the internal sd card it is so simple to do it only take like 3 mins and 7 screws ive done this and put a 16gb card in there
i cant post a link but heres the name of the vid "Flytouch 5 / Superpad 6 V10 - Disassembly - Access to internal TF"
it is not the same tablet but is pretty much the same
Tip use a knife to pop the caps off the outside i found this easier
try not to stab yourself.
thanks if i helped you out
noob
okay so i tried to install a new rom on my allwinner a10 bc1003 and ended up only booting a black screen i dont know what im doing as this is my first tablet an very little computer knolage but im interested i had seen in a post he used livesuit to flash the new rom.... i dont understand how that works if anyone could sit down and teach me that would be apriciated
---------- Post added at 12:21 PM ---------- Previous post was at 12:16 PM ----------
SolidSnakeGr said:
Actually it's not entirely bricked.. well I finally got it to work with LiveSuit 1.09 and managed to flash its firmware to a couple more roms.
1. sun4i_crane_t05a_20120409.img -> Ends up showing some messy stuff on the screen. Looks like the resolution is not correct.
2. sun4i_crane_futekoA90universal_20120531.img -> Shows lots of white stuff and colors switching jelly-like.. But still it doesn't work.
3. TAB360-364_Android_411_Jelly_Bean.img -> This is the official A10 Jelly Bean firmware for Yarvik TAB364 GoTab Gravity 8".. No wonder I still got back to the blank screen issue. I only notice the back light turn on and off following the pattern of normal functionality, only I'm not able to actually see it..
Well, at least I'm still able to keep flashing roms to it.. Any ideas?
I can't even find my stock rom to turn back to 4.0.4. Where exactly is it located in my recovery-mode backup?
Btw, in case it plays any part my tablet is 10.2''.
Any help would be greatly appreciated.
EDIT : Finally I figured it out! My correct stock rom is : sun4i_crane_bc1003.img
I found it through google and after flashing to it I managed to get my tablet at a working state. (ICS 4.0.4 ICS 4.0.3)
So, I'll now try to use more Jelly Bean roms without worrying about bricking it.
Oh, something I noticed that might help others too.. even though on the packaging it says Flytouch Superpad 8 Allwinner A10 this tablet model (BC1003) is actually the Flytouch Superpad 7 and that helped me find my correct rom. Keep that in mind from now on. I'll keep you updated if I succeed in booting to Jelly Bean.
Click to expand...
Click to collapse
okay im sitting at this point but i dont understand the flashing with livesuit
With the Windows utility "Phoenix Card" it is possible to burn the MaPan image mentioned above to a micro SD card. After inserting the micro SD card into the tablet and booting up the image will be flashed onto the tablet, indicated by a progress bar and a ticking sound.This works for our tablet, and should work for firmware for several Allwinner A10 and A20 tablets plus some other processor families (vimicro?).
where can i get Windows utility "Phoenix Card"
cant find 1 that works the inside says Yones toptech BC 1003 all winers A10
flusspferd said:
With the Windows utility "Phoenix Card" it is possible to burn the MaPan image mentioned above to a micro SD card. After inserting the micro SD card into the tablet and booting up the image will be flashed onto the tablet, indicated by a progress bar and a ticking sound.This works for our tablet, and should work for firmware for several Allwinner A10 and A20 tablets plus some other processor families (vimicro?).
Click to expand...
Click to collapse
hi ... i have a Yones toptech BC 1003 all winers A10 (superpad 8 / flaytouch) that im trying to fix...
after 3 days trying every possible firmware, and booting them from external sd card
all i could do was change de logo at boot start from (mapan to kosaco, to oem etc..)
than i had the idea of removing the internal sd card to look at it ...
and guess what it still runs the same with out no sd card in or out
so i thought ... the sd card was never read in the first place cause is damage or corrupted...
so on the 4th day im trying to format and partition the new internal sd card... hoping for the best.
so...
is the firmware installed in a built in memory ??
and how do i format the internall card TF card , and install all the software again
Problems with CWM v6.0.2.8
Sorry to interrupt people, but I'm quite new at this and I guess I made a mess....
I have a Flytouch Superpad VIII with A10 inside (BC1003), which is bricked.
Don't ask me how I got it this way, I guess **** happens.
Downloaded and installed CWM-based Recovery v6.0.2.8 only to find that on the log it cannot mount...
E: Can't mount /cache/recovery/command
E: Can't mount /cache/recovery/log
E: Can't open /cache recovery/log
E: Can't mount /cache/recovery/last_log
E: Can't open /cache recovery/last log
My idea is that I probably used the wrong version of CWM, but if not the case, please tell me.
Anybody know a fix on this?
I've already intalled ADB drivers on my PC and at least I can communicate with my device using ADB.
Any help on unblocking the device and then flashing it would be greatly appreciated
Hello. i want to ask if someone have Clockwork mod or some custom firmware on Prestigio PMP5670c Android 4.1.1.
I managed to root it, but i realy dont like this Android version and Prestigio is not intrested in upgrading.
Hey can someone make a recovery for this tablet.
Sent from my PMP5670C_DUO using xda premium
Shawes said:
Hello. i want to ask if someone have Clockwork mod or some custom firmware on Prestigio PMP5670c Android 4.1.1.
I managed to root it, but i realy dont like this Android version and Prestigio is not intrested in upgrading.
Click to expand...
Click to collapse
I started to do some work on that tabled, but stuck with kernel touchscreen configuration. See here.
Touch chip is Goodix GT911, screen size is 800x1280 px. I managed to get touch working but partialls. First aprox 1.2 inches of top of screen are not responsive to to touches. After that 1.5" touch works normally.
I'm pretty sure I'm sending wrong configuration data array to chip and thats why its not working as it should, but have no time at the moment to toy with it. If anyone experienced with Goodix chips, pm me with ideas...
stane1983 said:
I started to do some work on that tabled, but stuck with kernel touchscreen configuration. See here.
Touch chip is Goodix GT911, screen size is 800x1280 px. I managed to get touch working but partialls. First aprox 1.2 inches of top of screen are not responsive to to touches. After that 1.5" touch works normally.
I'm pretty sure I'm sending wrong configuration data array to chip and thats why its not working as it should, but have no time at the moment to toy with it. If anyone experienced with Goodix chips, pm me with ideas...
Click to expand...
Click to collapse
Update: I started to toy with stock kernel and cm10.2 (my first CM ever, was working with AOSP based SoC manufacturers sources). Problem is that device uses separate partition for internal sdcard, so have to disable emulated storage.
Things done:
- recovery
- android is built against precompiled stock kernel
Status:
- after bootanim and starting apps screen android reboots and starts back with bootanim. This was one day tryout, will debug it later today. Thanx to TeamNostalgia's preparation for cm10.2 on Amlogic MX. I used their framework and device stuff, upgraded with latest amlogic version of sources. Because of SLA I have with Amlogic, I cannot put it online.
any news abouth root final this tablet?
thx for info
stane1983 said:
I started to do some work on that tabled, but stuck with kernel touchscreen configuration. See here.
Click to expand...
Click to collapse
klobasica said:
any news abouth root final this tablet?
thx for info
Click to expand...
Click to collapse
On the link abouve is posted rooted stock firmware (mine post). To lazy ones click here
no, no...sorry i mean custom rom if is posable to create for this tablet...
klobasica said:
no, no...sorry i mean custom rom if is posable to create for this tablet...
Click to expand...
Click to collapse
It is. I'm not CM guy really, but its possible. If anyone interested, TeamNostalgia's github does have decent tree for Amlogic MXS tablets. I did some CM10.2 work for that tablet, but ended up with bootloop and reboot eventually. Didn't had time do debug it.
Here 4pda.ru/forum/index.php?showtopic=504411&view=findpost&p=29560411 is a customized firmware from Prestigio PMP3970B to work on Prestigio PMP5670C. But it does not run on PMP5670C, stands on the splash screen. Maybe someone will take to complete the firmware, it is better factory firmware for the tablet PMP5670C
ksh2000 said:
Here 4pda.ru/forum/index.php?showtopic=504411&view=findpost&p=29560411 is a customized firmware from Prestigio PMP3970B to work on Prestigio PMP5670C. But it does not run on PMP5670C, stands on the splash screen. Maybe someone will take to complete the firmware, it is better factory firmware for the tablet PMP5670C
Click to expand...
Click to collapse
I fixed U-Boot (wrote my own to support device tree kernel - 3.10.10) and fixed touch screen. I did not upload this fw, started to work yesterday on amlogic's 4.4 sources (they support both mx and m8 chipsets) (no, I cant share, I have SLA with them), I have boot, only left few things to test and then I'll upload 4.4.2.
Thank you for keep working! Waiting for rom)
Sent from my GT-I5510 using xda app-developers app
cyanodeff said:
Thank you for keep working! Waiting for rom)
Sent from my GT-I5510 using xda app-developers app
Click to expand...
Click to collapse
Here's beta version of rom: http://www.stane1983.com/prestigio_pmp5670c/
Read install instructions, needs to be installed twice, uboot still not perfect. Waiting for feedback
Btw, it's 4.2.2 rom, KitKat doesn't work good (unstable) on MXS chip.
Installed today morning. Seems all good! Thank you very much
Sent from my GT-I5510 using Tapatalk 2
babicsbalu said:
Unfortunatelly I can not able to install it because the second install is freezing all the time, now I can not install official 1.0.0.5 ROM, it stucked during the installation.
Click to expand...
Click to collapse
Rename uImage_recovery to recovery.img (when installing back stock firmware).
babicsbalu said:
Now I successfully installed the 1.0.05 but there is a quite big issue: I can not able to install anything from Play, the Download Manager is acutally (lots of system apps too) 0.0kb
Click to expand...
Click to collapse
I'm really sorry for inconveniences. With 1.0.05 files on sdcard, delete factory_update_param.aml file and boot into recovery (as if you want to install firmware). From menu using vol +/- and power for select choose factory reset (data partition is not formatted using old partition layout, thats why you have 0kb). After that you also can reflash firmware if you want (just select zip from sdcard).
stane1983 said:
Here's beta version of rom: http://www.stane1983.com/prestigio_pmp5670c/
Read install instructions, needs to be installed twice, uboot still not perfect. Waiting for feedback
Btw, it's 4.2.2 rom, KitKat doesn't work good (unstable) on MXS chip.
Click to expand...
Click to collapse
My daughter get this tablet from her grandfather on 03.05.2014 ( I guess she is lucky about that date ), and it was so slow and ugly and everything.
I installed your bety rom and everything is perfect. BUt after first reboot i get setup wizard again, but the first time after Install I only get FC ( just like I should ) but it didnt throw me back to setup wizard again.
Can I expect wizard setup every time I reboot or?
And Yes, thank you a lot for this awesome and fast work. The tablet is now so much more usable.
HVALA TI STANE MNOGO => THANK YOU STANE A LOT
@stane1983 I have the same problem as @babicsbalu. My pmp5670c is also stuck at black screen after rebooting and installing new stock firmware. I did both, renaming from uImage_recovery to recovery.img and deleting factory_update_param.aml and every time with the same result.
Please help me!
Or you can PM me (I'm from Croatia)
Hvala ti!
Well I also have prestigio tablet pmp5670C_BK_DUO and within a week it got bricked somehow. I guess that broken charging pin on cable had something to do with it - probably did a short circuit or something and boot loader got corrupt. Tabled was responding to connection of new charging cable, but only backlight turned on. There was no logo or anything.
I browsed several pages and nothing worked. I tried with official upgrade from SD card but it didn't work. It started to upgrade, android-upgrade logo came up, but after reboot nothing happened. Damaged bootloader was unable to start the tablet.
After a day or so I finally found a way how to unbrick it! Yeah.... So in attached file there is the detailed procedure, which I found on some Russian page.
Good luck!
Recovery.rar no longer available
imarkic said:
Well I also have prestigio tablet pmp5670C_BK_DUO and within a week it got bricked somehow. I guess that broken charging pin on cable had something to do with it - probably did a short circuit or something and boot loader got corrupt. Tabled was responding to connection of new charging cable, but only backlight turned on. There was no logo or anything.
I browsed several pages and nothing worked. I tried with official upgrade from SD card but it didn't work. It started to upgrade, android-upgrade logo came up, but after reboot nothing happened. Damaged bootloader was unable to start the tablet.
After a day or so I finally found a way how to unbrick it! Yeah.... So in attached file there is the detailed procedure, which I found on some Russian page.
Good luck!
Click to expand...
Click to collapse
I had a similar problem here and this method seems promising, but the recovery file indicated on the PDF is no longer available. Would you still have it lying around somewhere?
Thank you!!
PMP5670c Duo
I got this tablet 2 month ago, i have found on w w w 4pda ru 4 custom rooms for this tablet and i used google chrome to translate in english to understand what i have to do, i have instaled every one rom but i got a problem, with all custom rom the internal storage disapear. I instaled stock version now and the internal storage is there ready to be used. Custom roms are better than stock rom but it's annoyng me the missing internal storage. Anyone with this problem or anyone know how to fix it?
Edit: I instaled stock rom then i instaled again Firmware v.1.0.10 from MrCheba Repack and now i have internal storage working maybe reinstall the stock rom fix it.
I was rebooting my MTech Fusion(specs given below) after editing build.prop file and pushing a new SystemUI.apk(changed some images) and the phone got stuck on boot logo. I tried using data and cache wipe functions of stock recovery(No CWM for my device) but it didn't help. Can anyone please help with this??
device:
MTech Fusion
Chipset: MT6589
512 MB RAM
Android 4.2.1 JB stock; Rooted with busybox.
PowerVR SGX544 GPU
4GB internal storage, 1GB for apps
2GB SD card(little tight on the budget it's my third phone in a year)
At this point, best to reflash the ROM
nitin95 said:
Can anyone please help with this??
Click to expand...
Click to collapse
I think the only thing left, that you haven't done already, is to reflash.
I was going to suggest NeedROM, but saw no listings for your brand. I assume you've already completed a web search for you model's ROM, and have 'come up dry'.
Go to the company's website and send an E-mail or call (with a cheap VoIP provider, of course) their phone number and ask for a link to the stock ROM download for your phone. This should include flashing instructions.
Seems all of m-Tech Mobile's Service Centers are in India, and their web site's Download section is limited to Specs, 'Buy Now' and spam-filled 'Reviews'. So your only hope is a personal contact with Customer Service to explain what you need.
I had the same kind of boot-loop problem with a phone made by M-Horse in China, having discovered too late no one has ported CWM (or built a custom ROM) for it. I was very lucky to find a ROM for the exact model on needROM, complete with reflashing utility recommendations. That's all it took to restore the phone to 'out of the box' condition.
I don't think I'll buy another phone until I first go to the 'net and see what kind of support is available for it.
Belamigo said:
I had the same kind of boot-loop problem with a phone made by M-Horse in China, having discovered too late no one has ported CWM (or built a custom ROM) for it. I was very lucky to find a ROM for the exact model on needROM, complete with reflashing utility recommendations. That's all it took to restore the phone to 'out of the box' condition.
I don't think I'll buy another phone until I first go to the 'net and see what kind of support is available for it.
Click to expand...
Click to collapse
Thanks! Will give it a shot
(EDIT): I found a ROM for a phone with same specs on NeedROM, will try flashing it before going to customer support.
(EDIT 2): The ROM didn,t work, probably due to scatter file error. I went to MTech service senter and got the stock ROM back. Backing it up for future use in case i brick again. Thanks Belamigo for the suggestion
nitin95 said:
I was rebooting my MTech Fusion(specs given below) after editing build.prop file and pushing a new SystemUI.apk(changed some images) and the phone got stuck on boot logo. I tried using data and cache wipe functions of stock recovery(No CWM for my device) but it didn't help. Can anyone please help with this??
device:
MTech Fusion
Chipset: MT6589
512 MB RAM
Android 4.2.1 JB stock; Rooted with busybox.
PowerVR SGX544 GPU
4GB internal storage, 1GB for apps
2GB SD card(little tight on the budget it's my third phone in a year)
Click to expand...
Click to collapse
You can't just simply replace new Systemui... You have to Edit framework also... Suystemui must also be signed... Any wrong values in build.prop will lead to bootloop...
Flashing the stock rom is best solution to revert back.Also changing system will cause bootloops :angel:
Jyotirdeb said:
Flashing the stock rom is best solution to revert back.Also changing system will cause bootloops :angel:
Click to expand...
Click to collapse
Yeah I got the stock rom flashed.. Mtech service center guy did for free Now backed up the same so I can reflash by myself.
Sent from my Mtech FUSION using XDA Free mobile app
how to flash stock rom using flashtools if i cant turn on my phone? it is always stuck in boot screen..pls help @ Belamigo @ nitin95
Hi xda family greeting, i need u guys help and suggest best rom for my china tablet and how to do it. The spec come with mtk6797,kernel 3.4.67, gpu mali400mp, 6gb ram. The brand is not recognize but when using cpu-z app it showing brand alps, and named as x101...
And my tablet now black of death after i tried to factory reset the tab becoz of some lagging...( And yes im not rooting or flashing the stock rom im just using factory reset in the setting then all black cannot get into recovery mod even charging not showing anything... Help me guys i don't know much about android but it seem like something is missing in the tablet
Can any send me stock recovery of bsnl a50 tablet
Can anyone send stock recovery for bsnl a50 ( china tab)?
Hw:mt6582
Version installed :alps.kk1.mp1.v2.46
For more info check link i have given full tablet details
I have rooted with king root and tried to flash custom recovery but doing so i lost my stock recovery and the custom recovery is also not working and only the android is booting and working
Anyone can help to get stock or custom recovery thanks in advance
Device details: global.awok.com/tablet-pcs/bsnl_a50_tablet_10_1_inch_64gb_3gb_ddr3_android_4_4_4g_wifi_dual_cam_dual_core_1_5ghz_pink/dp-1383598/