Ever wondered why gps is so slow in our canvas 2? Dont blame it to micromax.. Coz its the same issue on all mtk fons
Ever heard about engineering mode? Exactly there lies the solution
Open engineering mode and follow these steps
in the Engineer mode for MTK devices,
you should go to “Location” and then to “Location
Based Services”:
Now, we tap on EPO and check that “Enable EPO” is
enabled and then press on “EPO IDLE”:
“EPO IDLE” will change to “EPO DOWNLOADING”, so
you will need to wait few minutes to download a file,
I suggest that use it with a Wifi connection.
Once EPO DOWNLOADING back again to “EPO IDLE”
we can press back and enter into YGPS:
In the YGPS you will need to press on “Hot”, “Full”
and “AGPS Restart”:
Thank you....
Related
Hello i read this theard on forum android serbia.In this theard we can se way for unlock telenor touch plus.I don`t know did can unlock and telenor one touch ot 990 this way. I please senior members to see this and say their opinions>, did is true and can we use for alcatel one touch ot 990.
How to unlock your Telenor Touch Plus.
1: Make a note somewhere in your IMEI number and the MAC / address you may need it later if you unlock after the WiFi does not work or you have any problems with the MAC address. Settings - About phone - Status IMEI Wi-Fi MAC address
2: Backup your phone using MyPhoneExplorer, or any other program because it deletes all the data (phonebook, messages, calendar)
3: Download the following files on your computer: OUK_P736VV1.0.0B13 21.04.2012. last official ROM (Default Stock ROM)
Kod:
http://files.podtwo.com/roms/stock/zte/blade2/OUK_P736VV1.0.0B13-update_signed.zip
TMV_Stock_Recovery – Stock Recovery
Kod:
https://www.box.com/s/6506d76c3edc2d468cad
TMV_Unlock - Aplikaciju za otključavanje
Kod:
https://www.box.com/s/00067a33efece7000f07
QPST program za Backup / Restore data
Kod:
https://www.box.com/s/03202f2b7e0412874954
(The program is used to backup phone settings, IMEI, MAC address)
4th Rename OUK_P736VV1.0.0Bxx-update_signed.zip to update.zip and copy to your memory card into the main directory.
5th Unzip all three archives (TMV_CWM_Recovery, and TMV_Unlock Install_QPST_FromGAF
.6th Connect phone to computer via cable. In the phone options enable USB Debugging option Settings - Application - Development - Debugging USB
7th Unpacked from the archive TMV_CWM_Recovery run install-recovery-windows.bat and wait. Stock recovery will be recorded and the phone will restart. This may take a few minutes. If you get <waiting for device> to mean that drivers are not installed properly and Windows did not recognize the phone. When all is finished turn off the phone (if you're able to extinguish it, just remove the battery).
8th Hold the Power button and Volume Down until you see the FTM on the screen.
9.From Install QPST unpacked the archive, run Setup.exe and install program
Backup through QPST:
First: Do backup your data as it is all erased.
2. Remove the archive and extract it and run setup.
Kod:
https://www.box.com/s/03202f2b7e0412874954
3. Put yourself in the recovery through a combination of buttons Power + Volume down button
4.Run QPST and mind you do in the bottom status bar, you have the option Server Running .... if you do not go to the Server and the server from the Run menu option. Picture
http://www.getandroidfree.com/GetAndV1.0/wp-content/uploads/2011/12/BackupUsingQPST-S1.jpg
5.Now add your unit. Go to the Ports tab and Add the new port.Choose USB / QC Diagnostic port and click OK.
Picture
http://www.getandroidfree.com/GetAndV1.0/wp-content/uploads/2011/12/BackupUsingQPST-S2.jpg
6. :Here you can view the list of ports you have chosen
Picture
http://www.getandroidfree.com/GetAndV1.0/wp-content/uploads/2011/12/BackupUsingQPST-S3.jpg
7. Now click the Start menu and click on Clients Software Download.
Picture
http://www.getandroidfree.com/GetAndV1.0/wp-content/uploads/2011/12/BackupUsingQPST-S4.jpg
8.Backup tab, then on Browse, and save the file somewhere on your computer and press Start. When it is finished you will have all the settings of your phone taken.
Picture
http://www.getandroidfree.com/GetAndV1.0/wp-content/uploads/2011/12/BackupUsingQPST-S5.jpg
Picture
http://www.getandroidfree.com/GetAndV1.0/wp-content/uploads/2011/12/BackupUsingQPST-S6.jpg
9. To restore the settings you go to the Restore tab. Over Browse button to open your settings and turn on Allow phone / file ESN mismatch, if necessary.
Picture
http://www.getandroidfree.com/GetAndV1.0/wp-content/uploads/2011/12/BackupUsingQPST-S7.jpg
10.When all this is done, turn off the QPST program, run from a folder TMV_Unlock Download.exe on Start to start unlocking. This process takes up to 10 minutes. When all is finished, return the settings from QPST program, described in the step above and you have the phone unlocked for all networks.
LOCK THIS.
Hi dejanxxxx!
Why need to download OUK_P736VV1.0.0B13-update_signed.zip? It is not used until the unlock process...
Hi, I've seen a few posts about the Eken T01 around here. And since I've rooted and installed CWM on mine. I thought I'd post a tutorial on how to go about it!
Rooting the Eken T01!
Rooting the deivce is simple, and I mean simple.
You'll need:
An Eken T01 (Of course)
SausageMOD Script
The link to the sausageMOD script is here.
Right, so to root the device you'll need too:
Connect your tablet, and make sure USB Debugging is enabled (And possibly the option which keeps the screen on)
Extract and open the .exe in the Sausagemod/script folder
Press 1, then 2. To check you have your tablet connected and ADB has root access.
Then press option 3. It'll ask you to press any key a few times, so keep watching the terminal
Thats it! You've rooted the Eken T01
Installing Clockworkmod 5.0.2.7 on the Eken T01
We'll be using CWM from the scroll extreme. But apparently the novotools version works too!
You'll need to download the script from here and then extract it.
Open it up, make sure your tablet is connected, with USB Debugging enabled.
Press option one, after pressing any key on the first screen of the script
After its finished copying, press any key again to take you back to the menu, then press option 2 to confirm it worked
Press Q if it did work.
Known bugs with this CWM: You need to poke around a bit to enable the back buttton, since the Eken T01 doesn't have a hardware back button, but the scroll does. I'm not sure whether the novotools version does have a working back button or not.
If this tutorial helped. Press the Thanks button. I'll be back soon with more tutorials for the Eken T01.
If you'd like to check out a forum specific to the T01. Check out dragondevs.com. They have one developer working on a modifcation for the stock rom at the moment.
Drivers and utilities:
Drivers AutoInstaller
SP Flash Tool v3.1316.0.150
Factory ROM:
ThL_W9.130702.JB42.V12.FHD.CN.COM.8P128_MT6589_Tuber_OV12830
My ROM:
[email protected]'s ROM v3.1_Deodex
[email protected]'s ROM v3.0_Deodex
[email protected]'s ROM v2.1_Deodex
[email protected]'s ROM v2.0_Deodex
[email protected]'s ROM v1.0_Deodex
CWM Recovery 6:
CWM 6.0.3.3
CWM 6.0.3.6
Very useful, thank you for sharing. :good::good::good:
e my friend, how you install this rom ? when you use recovery and factory rom ?
I´m testing [email protected]'s ROM v2.1_Deodex thank you for sharing.
Where did you find Factory ROM? I try find it but i can´t, this is the first location where i find it the rom.
Sorry my bad english.
All my firmware are put through FlashTool.
[email protected] said:
All my firmware are put through FlashTool.
Click to expand...
Click to collapse
my friend, what is the features of your rom ?
is it fully working? worth to try it ? acceptable for all day use?
All fine...
Thank you for your work. I have just flashed your 2.1 rom and the phone is really more stable and fast than with the factory rom.
One question: I tried to flash your CWM but in flash tool when i select the scatter file you put, there is no partition selected and is not possible to flash the CWM recovery. Could you review this zip file ? I tried to flash it wqith mobile uncle toolk I couldn't either
Regards from Madrid !
GPS FIX
GPS FIX
------------
This is for anyone having GPS Issues.
Before you start the procedure you need:
1. Rooting - This rom is rooted.
2. Get Mobileuncle Tools from play store
3. Get GPS Test from play store
4. Get Root explorer from play store or internet.
Procedure should be done outdoors:
1. Turn GPS off on your phone.
2. Open Root Explorer and find the mtkgps.dat file in /data or /data/misc
3. Delete mtkgps.dat
4. Reboot phone
5. Open Mobileuncle Tools
6. Tap on 'Engineer Mode'
7. Tap on 'Engineer Mode (MTK)'
8. Scroll across to 'Location'
9. Tap on 'Location Based Service'
10. Tap on 'AGPS' and then make sure 'A-GPS On/Off' is checked
11. Tap on 'EPO' and then make sure 'Enable EPO' is checked
12. Swipe down (notification bar) and turn GPS on
13. Hit back and then tap 'YGPS'
14. Wait until you get position lock (mine took about 5 seconds).
15. This process should create a new mtkgps.dat file.
16. Hit home button and open GPS Test.
17. You should get a position lock reasonably quickly.
i needed this !
djbxp said:
GPS FIX
------------
This is for anyone having GPS Issues.
Before you start the procedure you need:
1. Rooting - This rom is rooted.
2. Get Mobileuncle Tools from play store
3. Get GPS Test from play store
4. Get Root explorer from play store or internet.
Procedure should be done outdoors:
1. Turn GPS off on your phone.
2. Open Root Explorer and find the mtkgps.dat file in /data or /data/misc
3. Delete mtkgps.dat
4. Reboot phone
5. Open Mobileuncle Tools
6. Tap on 'Engineer Mode'
7. Tap on 'Engineer Mode (MTK)'
8. Scroll across to 'Location'
9. Tap on 'Location Based Service'
10. Tap on 'AGPS' and then make sure 'A-GPS On/Off' is checked
11. Tap on 'EPO' and then make sure 'Enable EPO' is checked
12. Swipe down (notification bar) and turn GPS on
13. Hit back and then tap 'YGPS'
14. Wait until you get position lock (mine took about 5 seconds).
15. This process should create a new mtkgps.dat file.
16. Hit home button and open GPS Test.
17. You should get a position lock reasonably quickly.
i needed this !
Click to expand...
Click to collapse
i needed, Thanks
Guys, there is no time .... How come - a hat decorated theme. By the way are already being tested are new firmware version, based on the July factory. Added localization for all languages. Integrated lot of tweaks ...
New!!! 02.09.2013 [email protected]'s ROM v3.0_Deodex
Changes:
1 . The firmware is based now on official July (Chinese). Transfer is executed for 100%
2 . Are added new tweaks of energy saving
3 . The gallery and the camera is replaced
4 . The new modem from 27/07/2013
5 . Boologo - separate thanks of gormiza is customized
6 . The Google services are updated
7 . SuperSU is updated
8 . Still something, but any more I don't remember
Can you make a spec-list in the 1st thread in which you explain what you've done in you rom
and instruction for flashing cmw and rom? :angel:
Discrud and
Testing [email protected]'s ROM v3_Deodex thank you for sharing.
Cant play video in the Super Galery [email protected]'s ROM v3_Deodex.
This is how the gallery from Lenovo, with this I can not do anything ....
New!!! 08.09.2013 [email protected]'s ROM v3.1_Deodex
Changes:
1 . Bugfix
thanks for the rom
[email protected] said:
New!!! 08.09.2013 [email protected]'s ROM v3.1_Deodex
Changes:
1 . Bugfix
Click to expand...
Click to collapse
We support the domestic manufacturer and chef: :good:
Thank you very much for this amazing work
Hey everyone,
I recently was given a Verizon galaxy s3 I want to use it with tmobile. I used these steps
a) Download Samsung Drivers if you do not already have them. It is an Exe file: DOWNLOAD
b) Run what you just downloaded, to install the drivers.
c) Download the ODIN3 Software, this software lets you flash (which means write to the hardware of your computer which is normally not possible) your phone. The file you are downloading is compressed, which means you need to first uncompress it. DOWNLOAD
d) Extract (Uncompress) the folder you just downloaded, and run ODIN3 which will be one of the files inside the folder you just extracted.
NOTE ODIN3 is an Executable File, which means you do not install it, you just click on it to run it.
e) Now we need to download the file VRALEC Bootchain. This file will be used by to allow us to flash (using the ODIN3 software) a customized recovery image on to your phone. DOWNLOAD
NOTE: What an image is, is simply a snap shot of a harddrive, sort to speak. Someone who has advanced knowledge of the Android OS, created a snap shot of their Phone "Harddrive" (firmware) so that others could simply replace their current Android OS, with the customized one.
f) Turn off your phone. HOLD DOWN the Volume Down Key, Home Key, and the POWER down key. As soon as the phone Vibrates release the POWER button only. Once the ODIN Screen comes up, release the other two buttons and hit the Volume UP key.
g) Now connect your phone to your computer using your USB Cable.
h) Now on your computer, bring up ODIN3 and click on PDA, this will bring up a file selector. You want to select the VRALEC Bootchain you just downloaded (VRALEC.bootchain.tar.md5 for example).
WARNING: DO NOT CLICK ANY CHECK-BOXES, YOU WILL DAMAGE YOUR PHONE.
NOTE: After you select the file, the box next to the PDA button should now be populated with the location of the file: C:\Users\yourname\Downloads\VRALEC.bootchain.tar.md5.
i) Now locate the Start button, located below the PDA button.
WARNING: DO NOT UNPLUG YOUR PHONE OR TURN IT OFF DURING THIS PROCESS.
NOTE: Once it is complete, your phone will restart.
j) After your phone restarts, go back to ODIN3 and click the Reset button, it is located right next to the Start button.
k) Unplug your phone and then turn it off, and finally take the back cover off.
l) We need to get back to the ODIN mode. Turn off your phone (if its not off already). Push and hold down the Volume Down Button, Home Button, and the POWER Button. As soon as the phone Vibrates release the Power Button only. Once the ODIN Screen comes up, release the other two buttons and hit the Volume UP Button.
m) Once you are in ODIN Mode connect your phone again to your computer
n) Now you need to download ClockworkMod Touch Recovery 6.0.2.3 (a recover image that you will use to replace your current Android OS with a Unlocked one). DOWNLOAD
o) After you download it, bring up the ODIN3 software again, and this time you want to UNCHECK Auto-Reboot. This is very important, after you uncheck it, the only option that should be CHECKED is the F.Rest Time option.
p) Now click on the Bootloader button and select the Clockwork recovery image we downloaded at step n. (CWM6023TouchVZW.tar.md5 for example)
NOTE: After you select the recovery image, the box next to the should display the location of the; C:\Users\yourname\Downloads\CWM6023TouchVZW.tar.md5
q) Now locate and click the Start button again, located at the bottom of the ODIN3 Panel
WARNING: DO NOT UNPLUG YOUR PHONE OR TURN IT OFF DURING THIS PROCESS.
r) After it has finished running, disconnect your phone, turn it off, and take out the battery. Leave the battery out for at least 20 seconds.
s) We need to now turn on the Phone into Recovery. To get into Recovery mode follow these steps; Turn off your phone (if its not off already). Push and hold down the Volume UP Button, Home Button, and the POWER Key. As soon as the phone Vibrates release the Power Button only.
NOTE Once you see "Recovery Mode..." at the top left of the screen you can let go of the buttons.
t) Once in recover mode, select reboot system now, after you click it, it will ask you if you want to disable recovery flash. YOU MUST SELECT "Yes - Disable recovery flash"
ATTENTION : The following step is very important, you must select Yes - Disable recovery flash
u) We need to now download the Super User Package to grant us Root. DOWNLOAD
NOTE: This package is a compressed zip file. DO NOT UNCOMPRESS THIS FILE, YOU NEED IT TO BE COMPRESSED.
v) Connect your phone back to your computer, and copy the zip file you just downloaded in step u, to your phone's External SD card. (SuperSU_Bootloader_FIXED.zip for example, will be the name of the file that you will copy over)
w) We now need to get into Recovery mode again. To get into Recovery mode follow these steps; Turn off your phone. Push and hold down the Volume UP Button, Home Button, and the POWER Key. As soon as the phone Vibrates release the Power Button only.
NOTE Once you see "Recovery Mode..." at the top left of the screen you can let go of the buttons.
x) Once you are in recovery mode, select "- install zip from sdcard"
y) Then click on "- choose zip from external sdcard"
z) Now find the file you downloaded and copied over. (SuperSU_Bootloader_FIXED.zip for example) and select it.
NOTE: if you can't see the file, you may need to scroll down, to find it.
Sigh... this is a long process.... I am past step z!
z1) Click on "- Yes - Install SuperSU_Bootloader_FIXED.zip"
z2) After its finished, a you will see the menu again. Click on "++++++ Go Back+++++++"
z3) Click on "- reboot system now" your system should now be restarting.
We are not done yet, we now need to add the Tmobile APNs to our phone, however, the phone is set up to prevent you to do this, because of greed, corruption and a broken system.
Here are the original instructions to allow APNs unlocking in its entirety : Full Guide
z4) go to the Play Store, then search for and install BuildProp Editor
z5) Once it is installed, open it up and it will as you to grant the application superuser access, click on "GRANT"
z6) click the phone Menu Button, and when the menu comes up, click on Edit
z7) Scroll all the way to the botton, and add these two lines to it:
ril.sales_code=LOL
ro.csc.sales_code=LOL
z8) After entering the new in the two new lines, click on Save Icon located top right. It will pop up a message near the bottom center that will let you know it was saved.
z9) After you save it, restart your phone.go to
•Settings
•More Settings
•Mobile Networks
•Access Point Names
Here are the original instructions to set up Tmobile APN in its entirety : Full Guide
z10) Click on the phones Menu Button and click on "+ New APN"
z11) Click on Name, set it "T-Mobile" then click OK
z12) Click on APN, and set it to "epc.tmobile.com" then click OK
z13) Click on MMSC and set it to "mms.msg.eng.t-mobile.com/mms/wapenc" then Click OK
z14) Click on the phones Menu Button and click on "Save"
z15) Click on "T-Mobile" and then restart your phone.
THATS IT! We are done... man
to root and unlock the bootloader and shows my phone is rooted but in step t I did not get the "Yes - Disable recovery flash" message. I did continue to the rest of the steps and it shows that my phone is rooted but I still can not stick to tmobiles towers and I keep getting a pop up asking if I want to switch to global. Does not clicking "Yes - Disable recovery flash" make the difference to making it work with tmobile? If so how can I fix this. Also, I still can not send or receive picture messages. I have the Samsung galaxy s3 i535 4.1.2. baseband version i535vrbmf1. I hope someone can help me
Instead of selecting global, try GSM/UTS
Sent from my Last Ever Samsung Device.
0331 said:
Instead of selecting global, try GSM/UTS
Sent from my Last Ever Samsung Device.
Click to expand...
Click to collapse
I have and still nothing. I have also tried to network unlock Via secret menu umts,debug screen,phone control, network lock but after that their is no options. Anyway to manually change the bandbase?
The baseband can be changed by flashing a different modem, I believe. What do you want to change it to?
The messages issue sounds like an APN issue to me.
Sent from my Last Ever Samsung Device.
---------- Post added at 03:51 PM ---------- Previous post was at 03:46 PM ----------
Where did you find the guide that you followed? Can you provide a link?
Sent from my Last Ever Samsung Device.
0331 said:
The baseband can be changed by flashing a different modem, I believe. What do you want to change it to?
The messages issue sounds like an APN issue to me.
Sent from my Last Ever Samsung Device.
---------- Post added at 03:51 PM ---------- Previous post was at 03:46 PM ----------
Where did you find the guide that you followed? Can you provide a link?
Sent from my Last Ever Samsung Device.
Click to expand...
Click to collapse
I was told by tmobile I need to unlock the phone and then change the baseband. I was able to change the apn without any app.
[FRP Removal Guide]
BLU Advance A4 - Model #A130Q
Security Patch: July 5, 2018
Requirements:
[NO WIFI NEEDED]
- 15 minutes of time
- One of the following - OTG cable & USB Flash Drive / micro USB Flash Drive / Computer with usb data cable (easiest way)
- Test DPC application (File attached to post at the bottom)
Before Starting:
Copy Test DPC application to Flash Drive or to internal storage of the phone using computer.
1) Hard Reset phone through key combo - Power off device, hold volume up button and power at the same time then when you see the Alcatel logo let off power and hold volume up button until you see recovery load. Goto factory reset and reset the phone.
2) Hold 2 fingers on screen or press accessibility to enable acccesibility mode. Press both volume buttons to disable talkback then forward onto the wifi and click on a wifi AP or setup a new one and if none are available click advanced, add proxy and then type in any random text highlight and press and hold on the Gmail button which will open app settings.
3) Goto app settings, press top 3 dots, and then press manage accounts. Now you are in settings. Goto Security and enable unknown sources then goto device administrators and disable device administrator.
4) Go to Storage and USB and scroll down to Explore then press it. Navigate to the Test DPC and install it. Now Open and setup as Device Owner. Follow instructions, make sure phone stays plugged in and is fully charged read/do all etc. Once finished and phone fully reboots and Test DPC runs finish it and the phone will reboot and will give you an error about needing to sign in which you wont be able to do since you are offline. Simply press the open windows toggle button which is the button on the right of the navigation bar at the bottom of your phone. Then flip back through the open windows to the settings window and press it.
5) Now to finish goto about, build, tap 7 times to enable Developer Options and then go back and into Developer Options. Next enable Oem Debugging. Now go back to settings and Factory reset the phone. Once rebooted follow through to setup your phone like normal. DONE
.
.
.
[]NOTE[]
This guide is only to aid those who own their device, have forgotten their google account password and need to return their device to working state.
q=]
-noidodroid