UPDATE:
I managed to fix it by first running the ACDU fix and then installing the European RUU over it! It even updates now!!
ACDU.exe (click the button on the right to download)
Released RUUs for HTC 8X (make sure to get one that corresponds to your device!)
KEEP IN MIND THAT THIS HAS WORKED FOR ME AND MY SECURITY UNLOCKED DEVICE,
THERE IS NO GUARANTEE THAT IT WILL WORK FOR YOU
IF YOU BRICK YOUR DEVICE, IT'S ON YOU.
Steps:
Put your device in the bootloader screen by powering it off, and then turning it back on while holding the vol up + vol down buttons simultaneously.
Connect the device to your computer and let Windows locate and install the driver needed. Wait until the driver is fully installed and/or you can see the word USB written on the bootloader screen.
Run the ACDU.exe file and let it do its job (This supposedly unbrands your phone!). It should restart a couple of times showing a green screen and then eventually go into the bootloader menu. It might say something like "UEFI for Key Provision ONLY" in red letters, ignore that.
Run the RUU you've downloaded and if everything goes as planned it should flash correctly. If not, make sure you've downloaded the correct RUU for your device and that it's not corrupted.
Enjoy your (unbricked and) updatable security unlocked device.
I hope this helps!!
Source used (it's in chinese): http://bbs.lumwp.com/thread-133710-1-1.html
---------------------------------------------------------------------------------------
Hello,
I have an HTC 8X that appears to be security unlocked and therefore could not receive updates.
In my infinite wisdom, I decided to try to flash the European RUU that has been released in the internet, hoping it would allow me to update the phone further. I did not proceed unprepared and I did indeed check that the phone was European (it initially had the OS version: 2.00.401.03) so it looked as if everything matched.
However, after starting the update, RUU flashed some UEFI related files and then the phone restarted. It started up and resumed the main firmware flashing process, stopping at the 1% mark and restarting back the bootloader.
The error code reported by RUU is the following:
Error [340]: ENCSS_VERIFY_ERROR
SSD Error, please flash subsystem does not encrypted image
The error message is kinda incoherent and I can't find anything about it (except in a thread in XDA, where someone states that this might be because I need an American firmware?), what's worse is that I'm left with a soft-bricked device that I can do nothing with since it can only boot to the bootloader.
The device is unlocked, unbranded and security unlocked (CID: 11111111), yet I'm still stuck.
If I try to flash only the UEFI stuff (by removing the RUU .nbh from the directory), the device is then able to boot to the HTC logo and get into the dual gear screen, where it gets stuck. The hard reset option does not seem to work at all, the phone restarts at the HTC logo if I keep the vol down button pressed. Strangely, I can get into the lightning screen but I dunno what that might do.
Did I mention that the device cannot shutdown? Yeah... It only restarts...
Does anyone know any way to fix this? Or why this might be occuring?
Click to expand...
Click to collapse
I've managed to fix it and I've included the solution in my first post. I hope this helps.
This just skips the CID check.
You can also change the CID by command to like HTC__001 and get the OTA's and be able to install RUU's the normal way.
help
xmoo said:
This just skips the CID check.
You can also change the CID by command to like HTC__001 and get the OTA's and be able to install RUU's the normal way.
Click to expand...
Click to collapse
i have a 8x(620e) bricked after updating wp8.1.It booted after updated but auto bootboop before wp8.1 gui.I try to hard reset,it can not help.So i try to flash it.but it says image version ledd than device version.Can you help me?Thanks.
fengsam said:
i have a 8x(620e) bricked after updating wp8.1.It booted after updated but auto bootboop before wp8.1 gui.I try to hard reset,it can not help.So i try to flash it.but it says image version ledd than device version.Can you help me?Thanks.
Click to expand...
Click to collapse
Nope I can't. I'm new in the Windows Phone world. I'm a Android pro
help
Potis20 said:
UPDATE:
I managed to fix it by first running the ACDU fix and then installing the European RUU over it! It even updates now!!
ACDU.exe (click the button on the right to download)
Released RUUs for HTC 8X (make sure to get one that corresponds to your device!)
KEEP IN MIND THAT THIS HAS WORKED FOR ME AND MY SECURITY UNLOCKED DEVICE,
THERE IS NO GUARANTEE THAT IT WILL WORK FOR YOU
IF YOU BRICK YOUR DEVICE, IT'S ON YOU.
Steps:
Put your device in the bootloader screen by powering it off, and then turning it back on while holding the vol up + vol down buttons simultaneously.
Connect the device to your computer and let Windows locate and install the driver needed. Wait until the driver is fully installed and/or you can see the word USB written on the bootloader screen.
Run the ACDU.exe file and let it do its job (This supposedly unbrands your phone!). It should restart a couple of times showing a green screen and then eventually go into the bootloader menu. It might say something like "UEFI for Key Provision ONLY" in red letters, ignore that.
Run the RUU you've downloaded and if everything goes as planned it should flash correctly. If not, make sure you've downloaded the correct RUU for your device and that it's not corrupted.
Enjoy your (unbricked and) updatable security unlocked device.
I hope this helps!!
Source used (it's in chinese): http://bbs.lumwp.com/thread-133710-1-1.html
---------------------------------------------------------------------------------------
Click to expand...
Click to collapse
could you list your bootloader message?
fengsam said:
could you list your bootloader message?
Click to expand...
Click to collapse
Well, after updating to GDR3, it seems that the bootloader messages have changed.
As of right now, it says
Security Unlocked
PM2320001 P S WP8 I (Before flashing ACDU, I think it used to be only "PM230001")
SBL1-1.0.21009.0
SBL2-1.0.21009.0
SBL3-1.0.21009.0
RPM-1.1.03078.0
TZ-303.000.241
UEFI-0.0.3030.0(175731) (Before updating, it used to be something like "15****", where * = numbers)
OS-4.12.401.01 (Before updating, it used to be 2.00.401.03)
CID-11111111
Radio-1.20b-32-19.04_15.67b.32.19 (Before flashing/updating, it used to be something like "1.11b.32.19.23")
fengsam said:
i have a 8x(620e) bricked after updating wp8.1.It booted after updated but auto bootboop before wp8.1 gui.I try to hard reset,it can not help.So i try to flash it.but it says image version ledd than device version.Can you help me?Thanks.
Click to expand...
Click to collapse
Ah, that's unfortunate. I don't know of a way to bypass the version check. =/ I don't understand why they're making things so difficult for end users. If you're flashing a full ROM, then you don't care what the previous one was... The only thing I can think of is that maybe on each update they blow a fuse so that you can't go back, like on the Xbox360
xmoo said:
This just skips the CID check.
You can also change the CID by command to like HTC__001 and get the OTA's and be able to install RUU's the normal way.
Click to expand...
Click to collapse
How would I go around doing that?
Potis20 said:
Well, after updating to GDR3, it seems that the bootloader messages have changed.
As of right now, it says
Security Unlocked
PM2320001 P S WP8 I (Before flashing ACDU, I think it used to be only "PM230001")
SBL1-1.0.21009.0
SBL2-1.0.21009.0
SBL3-1.0.21009.0
RPM-1.1.03078.0
TZ-303.000.241
UEFI-0.0.3030.0(175731) (Before updating, it used to be something like "15****", where * = numbers)
OS-4.12.401.01 (Before updating, it used to be 2.00.401.03)
CID-11111111
Radio-1.20b-32-19.04_15.67b.32.19 (Before flashing/updating, it used to be something like "1.11b.32.19.23")
Ah, that's unfortunate. I don't know of a way to bypass the version check. =/ I don't understand why they're making things so difficult for end users. If you're flashing a full ROM, then you don't care what the previous one was... The only thing I can think of is that maybe on each update they blow a fuse so that you can't go back, like on the Xbox360
How would I go around doing that?
Click to expand...
Click to collapse
Your message is same with mine.http://forum.xda-developers.com/showthread.php?t=2722104
fengsam said:
Your message is same with mine.http://forum.xda-developers.com/showthread.php?t=2722104
Click to expand...
Click to collapse
Well, unless we can find a way to bypass the OS version check set by HTC (or MS?), I guess you're stuck. =(
I was thinking of updating to 8.1 but after the whole ordeal above, I said "**** it, I'll get it when it's updatable! I'm not taking the change of bricking it again.."
..This captcha thing is starting to get very annoying...
Potis20 said:
Well, unless we can find a way to bypass the OS version check set by HTC (or MS?), I guess you're stuck. =(
I was thinking of updating to 8.1 but after the whole ordeal above, I said "**** it, I'll get it when it's updatable! I'm not taking the change of bricking it again.."
..This captcha thing is starting to get very annoying...
Click to expand...
Click to collapse
I think the OS version check set by htc.Because htc8s can still downgrade by reflashing ruu.I am very happy to update wp8.1,but bricked.
@Potis20 Can you re-upload the ACDU.exe file? The link says the file was removed...
Can someone upload ACDU.exe fix file again??
I have HTC wp 8x from O2 and i try to unlock with your instructions :good:
Threshergr said:
Can someone upload ACDU.exe fix file again??
I have HTC wp 8x from O2 and i try to unlock with your instructions :good:
Click to expand...
Click to collapse
I don't have the ACDU file but I was able to unlock my phone using the ACDU_UEFI_PROV_KEY.nbh file.
1. Download ACDU_UEFI_PROV_KEY https://mega.co.nz/#!UlMS1CyQ!rX-5-U6mmBHncVw6etFYeuSuV-OLX1De-jgkgEGf6FU
2. Put the ACDU file in the same directory as the ROMUpdateUtility (move the other .nbh files to another folder)
3. Run ROMUpdateUtility.exe
4. Phone should flash and unlock
5. Delete the ACDU_UEFI_PROV_KEY file
6. Move the UEFI_signed.nbh and RUU_signed.nbh files back
7. Run ROMUpdateUtility.exe again to flash ROM
Can someone upload ACDU.exe fix file again??
please !!!!!!!!!!!!!!
Same issue with HTC 8x Security Unlocked CID 1111111
Error [340]: ENCSS_VERIFY_ERROR
can you share your complete files package here?
thanks
i have downloaded latest nbh files for my HTC 8X by using windows device recovery tool and use the flash utility with nbh files as u said still no results. get the error : 340 encss verify error
SSD Error Please Flash subsystem does not encrypted image
Related
I have seen this come up many times as a question.. Probably needed a post of it's own...
Download this and move it to your ext-sd card (not in any folder) using htc file manager. Rename it to 0P6BIMG.zip
- https://www.androidfilehost.com/?fid=95916177934537454
Then reboot to bootloader and allow it to flash. This will give you back the latest TWRP. Boot back up and delete that zip off your sd card. IF you don't delete or rename it you won't be able to get to recovery via bootloader (it will keep trying to load that zip).
Then download this (doesn't matter to where-just remember where).
http://download.chainfire.eu/696/Sup...erSU-v2.46.zip
Reboot to TWRP manually and flash it. Bam... done.....
I accepted the OTA Lollipop update ( stupid ) and it broke root on me. I was S-off and unlocked. Did the above method and re-gained root
This works on 5.0.1
Thanks so much,
John
help!!
jjmstang said:
I accepted the OTA Lollipop update ( stupid ) and it broke root on me. I was S-off and unlocked. Did the above method and re-gained root
This works on 5.0.1
Thanks so much,
John
Click to expand...
Click to collapse
Hey so were you able to apply these steps using verizon m8 5.0.1 (lollipop), I really appreciate if you can get back to me ASAP. thanks :good:
viscocho13 said:
Hey so were you able to apply these steps using verizon m8 5.0.1 (lollipop), I really appreciate if you can get back to me ASAP. thanks :good:
Click to expand...
Click to collapse
Yes..that's what I wrote this for. Need to be s-off though
need s-off
dottat said:
Yes..that's what I wrote this for. Need to be s-off though
Click to expand...
Click to collapse
I looked for methods to s-off and I can't find the appropiate method, can you please help here! thanks in advance... :laugh:
viscocho13 said:
I looked for methods to s-off and I can't find the appropiate method, can you please help here! thanks in advance... [emoji23]
Click to expand...
Click to collapse
If on lollipop your only option right now is to have someone with a Java card do it for you.
Thank you so much for posting this. I've been looking for it endlessly.
I'm not all that experienced with flashing and I think I made a mistake somewhere.
I downloaded the first file, renamed it as specified, and placed it on the highest level of my external SD card. I rebooted using power + vol down and let it do its thing with the vertical loading bar. I suppose that means it flashed the file.
Then I rebooted, deleted the first file, and put the second file on the highest level of the external SD card. I rebooted again, selected "recovery", and was taken to the stock recovery, not TWRP.
Disregard this I goofed.
Sent from my HTC6525LVW using Tapatalk
PiperCub49 said:
Thank you so much for posting this. I've been looking for it endlessly.
I'm not all that experienced with flashing and I think I made a mistake somewhere.
I downloaded the first file, renamed it as specified, and placed it on the highest level of my external SD card. I rebooted using power + vol down and let it do its thing with the vertical loading bar. I suppose that means it flashed the file.
Then I rebooted, deleted the first file, and put the second file on the highest level of the external SD card. I rebooted again, selected "recovery", and was taken to the stock recovery, not TWRP.
Click to expand...
Click to collapse
You usually have to confirm flashing the zip. Can you verify it asks you to flash zip 1?
I'm not getting a confirmation message. Hmmm...
---------- Post added at 03:59 AM ---------- Previous post was at 03:12 AM ----------
When I reboot into the bootloader, I immediately get a message saying that it's loading 0P6BIMG.zip. There is a loading bar. Once the loading finishes, I get a message saying to press power to reboot, which I do. I plug my phone in and put the second file on the SD card. When I reboot into the bootloader, I select "Recovery" and it loads the stock recovery.
PiperCub49 said:
I'm not getting a confirmation message. Hmmm...
---------- Post added at 03:59 AM ---------- Previous post was at 03:12 AM ----------
When I reboot into the bootloader, I immediately get a message saying that it's loading 0P6BIMG.zip. There is a loading bar. Once the loading finishes, I get a message saying to press power to reboot, which I do. I plug my phone in and put the second file on the SD card. When I reboot into the bootloader, I select "Recovery" and it loads the stock recovery.
Click to expand...
Click to collapse
If your fastboot is working on your PC put the phone in fastboot mode.
Fastboot oem rebootRUU
Fastboot flash zip nameofzip.zip
Fastboot reboot-bootloader
Now try to boot to recovery
dottat said:
If your fastboot is working on your PC put the phone in fastboot mode.
Fastboot oem rebootRUU
Fastboot flash zip nameofzip.zip
Fastboot reboot-bootloader
Now try to boot to recovery
Click to expand...
Click to collapse
First of all, I wanted to thank you for your help with all of this. I really appreciate it.
I'm getting somewhere, but I'm not there yet. When I enter the 'fastboot flash zip nameofzip.zip' command, I get stuck at '<waiting for device>'. I've waited for over a half hour on a computer with a USB 3.0 port, and then the same on another computer with a 2.0 port. It's stuck there. I'm doing some research to see if I can find what is causing it to get stuck here.
PiperCub49 said:
First of all, I wanted to thank you for your help with all of this. I really appreciate it.
I'm getting somewhere, but I'm not there yet. When I enter the 'fastboot flash zip nameofzip.zip' command, I get stuck at '<waiting for device>'. I've waited for over a half hour on a computer with a USB 3.0 port, and then the same on another computer with a 2.0 port. It's stuck there. I'm doing some research to see if I can find what is causing it to get stuck here.
Click to expand...
Click to collapse
I'm thinking you should do two things. First unplug and reply your usb cable while it's waiting. Secondly check device manager and make sure it shows the correct driver for your phone is installed when your phone is in ruu mode. Each mode loads its own driver instance.
I did some more work and ton more research and took another couple steps forward. I watched a video of some guy flashing an RUU and noticed the prompt asking him to confirm flashing the zip, which I'm not getting. The process should be simple.
Before I go any further, will this method work with a locked bootloader? I'm s-off, but have a locked bootloader. If it won't work with a locked bootloader, I'm out of luck since there's really no way of unlocking the bootloader on the Verizon m8, right?
PiperCub49 said:
I did some more work and ton more research and took another couple steps forward. I watched a video of some guy flashing an RUU and noticed the prompt asking him to confirm flashing the zip, which I'm not getting. The process should be simple.
Before I go any further, will this method work with a locked bootloader? I'm s-off, but have a locked bootloader. If it won't work with a locked bootloader, I'm out of luck since there's really no way of unlocking the bootloader on the Verizon m8, right?
Click to expand...
Click to collapse
Install team viewer on your PC and shoot me the login info via pm and a good time later tonight to catch up and resolve this.
First thing I'm doing is unlocking that boot loader which should not be locked.
dottat said:
If on lollipop your only option right now is to have someone with a Java card do it for you.
Click to expand...
Click to collapse
I had spoken to scotty1223 about me getting an M9 and having him do the Java card trick but it looks like I may only get the M8 now.... The same card and process works ?
scotty1223 and I live in the same town (I think) or very, very close.
hallstevenson said:
I had spoken to scotty1223 about me getting an M9 and having him do the Java card trick but it looks like I may only get the M8 now.... The same card and process works ?
scotty1223 and I live in the same town (I think) or very, very close.
Click to expand...
Click to collapse
Yep. Works the same. We have a couple users too that have Java cards myself included. Scotty1223 will take fine care of you.
Verizon htc one m8 lollipop
Hi there, I'm stuck with the verizon htc one m8 on lollipop after taking the update without going s-off. Is there any way that someone can help me out with a Java card?
Thanks in advance!
emineh17 said:
Hi there, I'm stuck with the verizon htc one m8 on lollipop after taking the update without going s-off. Is there any way that someone can help me out with a Java card?
Thanks in advance!
Click to expand...
Click to collapse
Pm me and I will see who is closest to you
Root and S-off Verizon M8 5.0.1
Hello everyone,
I am quite new to this and although this is all a bit overwhelming, I appreciate everything I'm learning. I'm trying to get my Verizon M8 to work on gsm so that I can use a metro pcs sim. I'm running 5.0.1 and can't seem to find a way to root my phone and get s-off to even begin the process. Any pointers?
Hello,
After a failed Windows 10 upgrade attempt, my HTC 8x was working fine however after few days I attempted to soft reset it and all hell broke loose! Its stuck in reset gears loop ever since.
Note: Being a non-poster member (so far), I'm not allowed to post outside links so unable to post screenshots!
http: //s16.postimg.org/e58yok9th/image.jpg
http: //s1.postimg.org/jk31zmncf/image.jpg
I have tried the below however not successful, any help is appreciated...
1. Attempt to hard reset by holding down the volume down key while powering on the device > Result: Doesnt show the Exclamation ( ! ) symbol
2. Windows Phone Recovery tool doesnt detect the phone > choose my phone was not detected > Start the phone in boot loader mode by holding both volume up and down keys while powering on > It goes to boot loader mode however reports "Software package is not found on server"!
http: //s29.postimg.org/ivtb6n21j/image.jpg
3. RUU_ACCORD_WR_GDR3_00_MR_HTCCN_CHS_CT_4.13.1401.03_0.21.70_RETAIL_ENC_RELEASE.exe and similar packages > Old package error
http: //s22.postimg.org/gfcdp55s1/NBFError.jpg
4. HTCDeviceInfo.exe successfully detects the device however HTCRomUpdater fails to flash .NBH file http: //s18.postimg.org/5kpf6h70p/HTCRom_Flashor_Error.jpg
5. FFUTool.exe doesnt detect the device! http: //s2.postimg.org/52daia255/FFUTool_Failure.jpg
6. Thor2 doesnt decte the device http: //s4.postimg.org/ei60y1b1p/Thor2_Error.jpg
Is there ANYTHING else I can do to get this device working? Or buying a new phone is the only solution?
Fixed!
I was able to fix the device using NSU with original firmware FFU.
Where did you find?
k00lf1re said:
I was able to fix the device using NSU with original firmware FFU.
Click to expand...
Click to collapse
where did you find original firmware?
How were you able to install Windows 10 mobile on the 8X man? Can you do that again?
killerz0ne said:
How were you able to install Windows 10 mobile on the 8X man? Can you do that again?
Click to expand...
Click to collapse
windows phone 10 is not available for htc 8x now. old methods not work anymore now.
rza35 said:
windows phone 10 is not available for htc 8x now. old methods not work anymore now.
Click to expand...
Click to collapse
I am well aware of that. Do you guys think we will ever be able to install W10 on our phones. Contacted HTC support and they said that the 8X will not be compatible with W10 because of some hardware limitations, but they were not willing to tell specifics. What are the chances that we will be able to still install W10 by unofficial means?
k00lf1re said:
I was able to fix the device using NSU with original firmware FFU.
Click to expand...
Click to collapse
Can you maybe go into a bit more detail on what you had to do to get the original firmware on the device? I'm having the same problem after getting the update from MS today.
mbrio said:
Can you maybe go into a bit more detail on what you had to do to get the original firmware on the device? I'm having the same problem after getting the update from MS today.
Click to expand...
Click to collapse
Same here. Installed Win10 update and phone is bricked. Need the detail and links to flash it
k00lf1re said:
I was able to fix the device using NSU with original firmware FFU.
Click to expand...
Click to collapse
How did you do it, when I use NSU it doesn't want to recognise my 8x
The fact is that the update was sent to ALL HTC 8X in the world. Mine installed the update during the night without my consent.
Microsoft will probably blame Skynet for trying to terminate all and each 8x there is.
Well...Mine is broken now. I'll be waiting for official fixes.
WaGo! said:
The fact is that the update was sent to ALL HTC 8X in the world. Mine installed the update during the night without my consent.
Microsoft will probably blame Skynet for trying to terminate all and each 8x there is.
Well...Mine is broken now. I'll be waiting for official fixes.
Click to expand...
Click to collapse
Exactly. Still bricked (stuck in reboot loop) and waiting for some official guidance but so far nothing...
BrannanD said:
Exactly. Still bricked (stuck in reboot loop) and waiting for some official guidance but so far nothing...
Click to expand...
Click to collapse
My HTC 8x routine now:
1- Turn On.
2- Show message about the unsuccessful update.
3- Play the alarm (set to play daily at 7 am)
4- Turn Off.
5- GoToAndPlay(1) hahahahahahahha
Spent hours to restore some other rom, only got "INVALID VENDER ID" (sic) by the ROMUpdateUtility. My phone completed the update, seems to work fine, just reboots randomly after a couple of minutes. Had to setup wifi after a hard reset, otherwise apps were missing, including the Settings app. And the letters are tiny. This is sad and hilarious. Also, camera is gonsky.
gabest11 said:
Spent hours to restore some other rom, only got "INVALID VENDER ID" (sic) by the ROMUpdateUtility. My phone completed the update, seems to work fine, just reboots randomly after a couple of minutes. Had to setup wifi after a hard reset, otherwise apps were missing, including the Settings app. And the letters are tiny. This is sad and hilarious. Also, camera is gonsky.
Click to expand...
Click to collapse
Where did you get the ROMUpdateUtility (and a suitable ROM) from?
BrannanD said:
Where did you get the ROMUpdateUtility (and a suitable ROM) from?
Click to expand...
Click to collapse
I think you misunderstood me, no roms worked. There are many on the internet, even here on this forum. There seems to be an id in the phone and it does not match with the package.
Tried these with my t-mobile branded EU phone, all invalid.
RUU_ACCORD_U_APO_00_HTC_Europe_2.00.401.03_1.11b.32.19.23_2_15.42.32_RETAIL_ENC_RELEASE
IMG_ACCORD_U_GDR2_00_S_HTC_Europe_3.41.401.01_1.17b.32.19.14_15.62b.32_RETAIL_ENC_RELEASE
RUU_ACCORD_WR_GDR3_00_MR_HTCCN_CHS_CT_4.13.1401.03_0.21.70_RETAIL_ENC_RELEASE
Also talked with HTC live support, they have no idea of course.
Windows Phone Recovery Tool detects the phone, but can't offer any ROM.
terible
gabest11 said:
I think you misunderstood me, no roms worked. There are many on the internet, even here on this forum. There seems to be an id in the phone and it does not match with the package.
Tried these with my t-mobile branded EU phone, all invalid.
RUU_ACCORD_U_APO_00_HTC_Europe_2.00.401.03_1.11b.32.19.23_2_15.42.32_RETAIL_ENC_RELEASE
IMG_ACCORD_U_GDR2_00_S_HTC_Europe_3.41.401.01_1.17b.32.19.14_15.62b.32_RETAIL_ENC_RELEASE
RUU_ACCORD_WR_GDR3_00_MR_HTCCN_CHS_CT_4.13.1401.03_0.21.70_RETAIL_ENC_RELEASE
Also talked with HTC live support, they have no idea of course.
Windows Phone Recovery Tool detects the phone, but can't offer any ROM.
Click to expand...
Click to collapse
same issue. I installed Windows insider and enrolled fast program. yesterday, phone noticed me have an update. I downloaded and wait 10 hours, but it's still "migrating data ..."
I press power then back button, I see lockscreen and unlimmited number of password length. the live tile screen so miscellaneous and several app not access (phone, mess, setttings, store ..). It says " need go to store ...".
terrible ... I've tryed newest Windows phone recovery tool 2.1.2. It detect my phone but say "no software package on server"
did you check http://forum.xda-developers.com/htc-8x/development/ruu-collection-t2916107
Isich said:
did you check http://forum.xda-developers.com/htc-8x/development/ruu-collection-t2916107
Click to expand...
Click to collapse
Those links are all offline -> 404 error
What about this topic the procedure should be similar to flash http://forum.xda-developers.com/showthread.php?t=2137556
it has link to official rom HTC_Europe_2.00.401.03 which is at http://www.androidruu.com/?developer=Accord
http://matboot.blogspot.bg/2015/02/officestockupromhtc8xACCORD.html
My phone does not want to recognize the image files on a pen drive when I hold the cam button. It just boots Windows normally.
EDIT: Managed to buy an y-cable and the rom flashed from the pen drive! Back to 8.1 again.
Hi, guys!
Does anyone know how to unhard-brick A9? I killed HBOOT accidentally. Now it's only detected as Qualcomm Device and nothing is being loaded?
I have patched in hex editor and removed all that annoying text that came in red (without changing the checksum) from `aboot.bin`, that I extracted with `dd` from mmcblk0p12 partition. Later, I ran `fastboot flash aboot aboot.bin` under download mode and it didn't work (I also tried it under `fastboot oem rebootRUU`); Writing mmcblk0p12 partition with `dd` under `adb shell` also did not do anything..
Then I rebooted to bootloader and ran `fastboot flash aboot aboot.bin`. The message was - success. I happily rebooted and that was the end of the my HTC One A9 .
Is there a way to fix this dead phone - it's hard bricked!?
Also, could anyone explain, why it happened. I felt like I was doing everything correctly?
Thanks
qooob said:
Hi, guys!
Does anyone know how to unhard-brick A9? I killed HBOOT accidentally. Now it's only detected as Qualcomm Device and nothing is being loaded?
I have patched in hex editor and removed all that annoying text that came in red (without changing the checksum) from `aboot.bin`, that I extracted with `dd` from mmcblk0p12 partition. Later, I ran `fastboot flash aboot aboot.bin` under download mode and it didn't work (I also tried it under `fastboot oem rebootRUU`); Writing mmcblk0p12 partition with `dd` under `adb shell` also did not do anything..
Then I rebooted to bootloader and ran `fastboot flash aboot aboot.bin`. The message was - success. I happily rebooted and that was the end of the my HTC One A9 .
Is there a way to fix this dead phone - it's hard bricked!?
Also, could anyone explain, why it happened. I felt like I was doing everything correctly?
Thanks
Click to expand...
Click to collapse
Post an photo of device manager please [emoji14]
Inviato dal mio HTC One A9 utilizzando Tapatalk
You mean how it's detected under Windows Device Manager? It's actually different in Windows/Linux. I use Linux. But I could reload into Windows?
Thanks, here is the screen-shot of device manager, in case I got you correctly?
So, should I throw it away now?
qooob said:
So, should I throw it away now?
Click to expand...
Click to collapse
Can you get into download mode?
No, just blank screen. Like I already mentioned - HBOOT seems to be dead.
qooob said:
No, just blank screen. Like I already mentioned - HBOOT seems to be dead.
Click to expand...
Click to collapse
Helo guys,
I also hard bricked meine. Is there any solution to get it back ?
Thanks a lot for your answer.
Regards,
petithomme2005 said:
Helo guys,
I also hard bricked meine. Is there any solution to get it back ?
Thanks a lot for your answer.
Regards,
Click to expand...
Click to collapse
I don't think there is a solution yet. You need a programmator (device) to fix it. Take it back to store. They should give you your money back or take it to HTC support, they will fix it very quickly, in case they have a special device.
qooob said:
I don't think there is a solution yet. You need a programmator (device) to fix it. Take it back to store. They should give you your money back or take it to HTC support, they will fix it very quickly, in case they have a special device.
Click to expand...
Click to collapse
I have S-off and have installed cm13. I think that my warranty is gone. Du you think that they will repair it without asking to pay for it ?
Regards.
if warranty is gone than they will not fix it. for free
asadnow2k said:
if warranty is gone than they will not fix it. for free
Click to expand...
Click to collapse
i hope that the community will find a solution. Thanks a lot for your answers.
Regards,
petithomme2005 said:
I have S-off and have installed cm13. I think that my warranty is gone. Du you think that they will repair it without asking to pay for it ?
Regards.
Click to expand...
Click to collapse
They could actually. Do you have bootloader dead? If you hold power + volume-up, does the screen show anything (bootloader)?
Or it's black no matter what?
qooob said:
They could actually. Do you have bootloader dead? If you hold power + volume-up, does the screen show anything (bootloader)?
Or it's black no matter what?
Click to expand...
Click to collapse
The bootloader is dead and when i hold the power+volume-up i get a black screen and after that it stucks on screen with HTC on it with the warning message (red color)
Regards,
petithomme2005 said:
The bootloader is dead and when i hold the power+volume-up i get a black screen and after that it stucks on screen with HTC on it with the warning message (red color)
Regards,
Click to expand...
Click to collapse
It's easy to fix. Your bootloader is not dead. When I get home I'll find exact instructions for you.
qooob said:
It's easy to fix. Your bootloader is not dead. When I get home I'll find exact instructions for you.
Click to expand...
Click to collapse
Thank you, thank you, thank you. You will save my time
Regards,
petithomme2005 said:
Thank you, thank you, thank you. You will save my time
Regards,
Click to expand...
Click to collapse
Meanwhile, tell me - do you want CM or get back to stock?
I would like to install cm13, but the problem that i had is that the updates doesn't work any more for me as since Mail i think cm13 updates are based on 1.57 firmware version and my firmware was 1.27 version.
I would like to upgrade the firmware first before installing the last nightly cm13.
I hope you understood what i mean.
Thanks a lot.
Regards,
My problem was opposite. Back then I couldn't install CM because it didn't work with 1.56 and I had to downgrade from 1.56 to 1.27.
Can not say what is now. If you sure that you have version 1.27 installed and it still doesn't work then you need to upgrade to 1.56.
Go here and download latest ZIP firmware for your region (phone): http://forum.xda-developers.com/one-a9/general/wip-ruu-htc-one-a9-t3240344
Then flash it by going to Bootloader (turning phone off and then holding together power and volume down) - search Google or check here if doesn't work - http://www.technewscentral.co.uk/enter-fastbootbootloader-mode-htc-one/id_7930
To flash RUU just rename downloaded RUU file to 2PQ9IMG.zip, put it to the flash card and load in Download mode.
It will delete all data from your phone. It's worth trying to make a backup of your data partition first (in case you have apps and its important data). Afterwards, flash CM, and try to reboot. If it works. Flash custom recovery and then restore data partition.
In case it doesn't load, then I can't tell what exactly to do. Like I already said, I had to downgrade to 1.27 to make CM work 6 months ago. CM might change by now and now requires 1.56 to load. It's normal and very possible.
You might search Google to find out how to flash only firmware.zip without deleting data all the time. Back then it didn't work for me.
To downgrade firmare (just in case you need this), just goto to adb mode and run the following code to be able reflash 1.27 version again (need to change the version number to something lower than 1.27 and only then 1.27 RUU zip could be flashed)
Code:
adb shell
echo -ne "1.10.401.7\x00\x00" | dd of=/dev/block/mmcblk0p28 bs=1 seek=2208
exit
adb reboot bootloader
Good luck.
qooob said:
My problem was opposite. Back then I couldn't install CM because it didn't work with 1.56 and I had to downgrade from 1.56 to 1.27.
Can not say what is now. If you sure that you have version 1.27 installed and it still doesn't work then you need to upgrade to 1.56.
Go here and download latest ZIP firmware for your region (phone): http://forum.xda-developers.com/one-a9/general/wip-ruu-htc-one-a9-t3240344
Then flash it by going to Bootloader (turning phone off and then holding together power and volume down) - search Google or check here if doesn't work - http://www.technewscentral.co.uk/enter-fastbootbootloader-mode-htc-one/id_7930
To flash RUU just rename downloaded RUU file to 2PQ9IMG.zip, put it to the flash card and load in Download mode.
It will delete all data from your phone. It's worth trying to make a backup of your data partition first (in case you have apps and its important data). Afterwards, flash CM, and try to reboot. If it works. Flash custom recovery and then restore data partition.
In case it doesn't load, then I can't tell what exactly to do. Like I already said, I had to downgrade to 1.27 to make CM work 6 months ago. CM might change by now and now requires 1.56 to load. It's normal and very possible.
You might search Google to find out how to flash only firmware.zip without deleting data all the time. Back then it didn't work for me.
To downgrade firmare (just in case you need this), just goto to adb mode and run the following code to be able reflash 1.27 version again (need to change the version number to something lower than 1.27 and only then 1.27 RUU zip could be flashed)
Code:
adb shell
echo -ne "1.10.401.7\x00\x00" | dd of=/dev/block/mmcblk0p28 bs=1 seek=2208
exit
adb reboot bootloader
Good luck.
Click to expand...
Click to collapse
I can not go to booloader, i tried all the possibilities but without success.
For those of you that are rooted and would like to return back to stock with a relocked bootloader follow the steps.
This could also be useful for those of you stuck with a non bootable device. It will make your device eligible for warranty replacement again.
1. Flash stock boot.img (link) with the following command:
Code:
Fastboot Flash boot Stock_Boot.img
2.Re-lock bootloader with
Code:
Fastboot flashing lock
3. Enter recovery with Vol+ and USB plugged in. Then go down to wipe and Factory restore. Reboot and DONE
Hope this tip is useful to some.
See yah
Stock Boot.img Link
https://drive.google.com/open?id=1SqjkwVzNC3nAqDkNDMdEpqQH7viXDmb4
Is this the stock boot image for the regular non-carrier Razer Phone?
Kalveitt said:
Is this the stock boot image for the regular non-carrier Razer Phone?
Click to expand...
Click to collapse
This is for Non-Carrier.
Confirmed , you just made my day sir . i resurrect my device i flashed how you said with that command but i need to add -i 0x1532 , i got a message that is gonna flash it on b partition ,he said is done , after i restart it i got a message on phone (erasing) after i done the steps to factory reset it , i managed to get in the stock recovery, after 10 minutes i booted in the software all fine but not the wifi and flashlight ,
thank you once again for your hard work.
we keep in touch maybe i can do the wifi and flashlight
my device
Razer three uk
Anyone flash back to stock and have issues installing the latest update? Downloads but won't install?
So I relocked the bootloader before this file was released, by mistake my phone has twrp on both partitions, so when ever I boot it just says device corrupt and reboot I can however access qualcom diagnostics by pressing volume up + volume down at the same time, just wondering if phone can be restored through that interface
Btw as I'm finding out.. This doesn't reset to stock! It does relock your phone and you loose root, but any changes made to the system files while you were rooted sticks.. Ie hosts file changes. I'm back to "stock" and the adaway hosts file changes are still present.. I expect other changes are still there too and that's why I can't flash the update. guess I'm waiting for factory images for a full stock as well)
mikeandjaimie said:
Btw as I'm finding out.. This doesn't reset to stock! It does relock your phone and you loose root, but any changes made to the system files while you were rooted sticks.. Ie hosts file changes. I'm back to "stock" and the adaway hosts file changes are still present.. I expect other changes are still there too and that's why I can't flash the update. guess I'm waiting for factory images for a full stock as well)
Click to expand...
Click to collapse
Hopefully they get released at all at this point...sure looking less and less likely at this juncture with incremental push updates coming from Razer.
mikeandjaimie said:
Btw as I'm finding out.. This doesn't reset to stock! It does relock your phone and you loose root, but any changes made to the system files while you were rooted sticks.. Ie hosts file changes. I'm back to "stock" and the adaway hosts file changes are still present.. I expect other changes are still there too and that's why I can't flash the update. guess I'm waiting for factory images for a full stock as well)
Click to expand...
Click to collapse
Or if someone with a US/NA Razer Phone was nice enough to upload and post there TWRP backups before the the partitions were modified. We have a backup for the 3UK people, but one from US/NA Razer Phone, and one from the EU/Non Carrier Razer would help alot of people. I know people have them, just no one willing to share I guess Will probably be months if Razer ever actually posts the Factory Images.
There have been files for both uploaded and it was determined you couldn't use them for 3 phones already.. That's how alot of people got non working phones that just say corrupted now..
Gotta wait till factory images are released if you are on 3.
mikeandjaimie said:
Btw as I'm finding out.. This doesn't reset to stock! It does relock your phone and you loose root, but any changes made to the system files while you were rooted sticks.. Ie hosts file changes. I'm back to "stock" and the adaway hosts file changes are still present.. I expect other changes are still there too and that's why I can't flash the update. guess I'm waiting for factory images for a full stock as well)
Click to expand...
Click to collapse
I manage to find the location of the ota Update.zip and tried flashing it in the stock recovery but it also fails on stage 2.
As you pointed it out. The update is failing because it's still recognizing the system as modified.
I'll leave my link up to help those who are stuck on a boot loop with an unlocked bootloader this will at least make them eligible for warranty replacement so it's something... Follow the steps and then send it off to Razer for warranty replacement. It's a shame really to send out a phone that could easily be fixed with system images. Razer has really dropped the ball. Not having system images from day one really hurt the enthusiast development for this device. If your not able to send it out for warranty replacement then all you can really do is wait for Razer to release the images and I think they may not release them until they release Oreo.
I followed the step-by-step for putting twrp on mine. All seems to go well but it just keeps booting back into bootloader. If I turn it off and hold the vol+ while plugging in the USB I just get the Razer logo and nothing. When I finally gave up I flashed the stock boot in the OP. I'm up and running now but no BT and the latest update just fails. Relocked the BL and no system changes were made since TWRP never seems to have installed, if though I got a successful when complete. I hate to send this back, anyone know if they can reflash it remotely? I'll pay the fee, just need the phone working on WiFi again.
Does this method also work if am rooted, running a stock 8.1 rom and kernal?
Solved Flash Razer Phone To Stock and gain OTA capable!!
This is for the Razer Phone!!!! Fixed Warranty and OTA Update!! As if freshly purchased!!!!
I figured out that unless you use the Razer provided images from their support site your phone will not function properly as any other procedure will be extremely time consuming on a command prompt!!! Imagine individually flashing all components in their respective orders and flashing to both partitions is a requirement so use the provide images and the flashall.sh command included in the downloaded file.
The instructions for gaining the ability to flash the update via windows cmd.
follow the original instructions from the razer support site and the do this for the connection or what it's actually called (Environment variables) you will need to navigate on your pc to the system properties window the click on environment variables, two panes in the window at the lower pane look for the PATH line which is the pathe for the variable to point cmd to file system where your stock razer update is located. If you followed all steps : usb drivers, androis sdk 28.xx or higher extracted to C:/adb folder, navigated to system window then update driver connect phone in bootloader mode then open update driver browse computer let me pick from a list of drivers on my computer and install the android bootloader interface continue even though it says not recomended it works.
now open your razer downloaded factory file and double click flashall.sh and wait till finished then stop the reboot and boot to booloader and open windows cmd and type fastboot devices then type fastboot flashing lock and lock it up, Done sorry for the unorganized text but I'm sure nobody cares as long as it works right? !#fi enjoy!!!
Solved!!!!!!!!!!!!!
---------- Post added at 06:41 AM ---------- Previous post was at 06:20 AM ----------
Mike02z said:
I followed the step-by-step for putting twrp on mine. All seems to go well but it just keeps booting back into bootloader. If I turn it off and hold the vol+ while plugging in the USB I just get the Razer logo and nothing. When I finally gave up I flashed the stock boot in the OP. I'm up and running now but no BT and the latest update just fails. Relocked the BL and no system changes were made since TWRP never seems to have installed, if though I got a successful when complete. I hate to send this back, anyone know if they can reflash it remotely? I'll pay the fee, just need the phone working on WiFi again.
Click to expand...
Click to collapse
I solved this and if you need detailed instructions or help anyone can ask and I will help and yes it does return it to brand new fresh ota and warranty is returned, everything works as it should no bugs wifi works and data on sim.
As for twrp you should flash it to one slot not both as you may know system is on both slots you could have two slots with twrp and no system lol I did that before!
Your phone can be stock but not ota with twrp fyi.
mikedeboefis said:
Solved!!!!!!!!!!!!!
---------- Post added at 06:41 AM ---------- Previous post was at 06:20 AM ----------
I solved this and if you need detailed instructions or help anyone can ask and I will help and yes it does return it to brand new fresh ota and warranty is returned, everything works as it should no bugs wifi works and data on sim.
As for twrp you should flash it to one slot not both as you may know system is on both slots you could have two slots with twrp and no system lol I did that before!
Your phone can be stock but not ota with twrp fyi.
Click to expand...
Click to collapse
Thanks, but I returned my Razer within the first 30 days. Just not for me.
mikedeboefis said:
This is for the Razer Phone!!!! Fixed Warranty and OTA Update!! As if freshly purchased!!!!
I figured out that unless you use the Razer provided images from their support site your phone will not function properly as any other procedure will be extremely time consuming on a command prompt!!! Imagine individually flashing all components in their respective orders and flashing to both partitions is a requirement so use the provide images and the flashall.sh command included in the downloaded file.
The instructions for gaining the ability to flash the update via windows cmd.
follow the original instructions from the razer support site and the do this for the connection or what it's actually called (Environment variables) you will need to navigate on your pc to the system properties window the click on environment variables, two panes in the window at the lower pane look for the PATH line which is the pathe for the variable to point cmd to file system where your stock razer update is located. If you followed all steps : usb drivers, androis sdk 28.xx or higher extracted to C:/adb folder, navigated to system window then update driver connect phone in bootloader mode then open update driver browse computer let me pick from a list of drivers on my computer and install the android bootloader interface continue even though it says not recomended it works.
now open your razer downloaded factory file and double click flashall.sh and wait till finished then stop the reboot and boot to booloader and open windows cmd and type fastboot devices then type fastboot flashing lock and lock it up, Done sorry for the unorganized text but I'm sure nobody cares as long as it works right? !#fi enjoy!!!
Click to expand...
Click to collapse
Yeah.. I need help on this one. I tried it and fastboot doesn't allow me to flash_all script.
How do you even double click flashall.sh?
I know this is kind of old but I'm currently having the same problem as a person above. I've tried using the flash_all command but it will only stay at "waiting for device" and doing flash_all.sh doesn't work.
Hi guys,
Ive got here Android version 8.0.0 and OTA 2.33.401.19 . Try to upload to Android pie but it shows a popup with (there was unexpected error and the file system may be corrupted. Please contact HTC support for further assistance). HTC want me to send my phone and sent me those prices ...had couple of bad experiences previously with their support(HTC M7, U10).
Does anyone have got this problem?
Go to Settings => About => Software Information
and tell us the Software Number.
Install Simple CID Getter from Google Play Store and tell us the CID it shows.
Then we'll find you an appropriate RUU and OTA to update your phone to Android Pie without needing HTC's help at all.
Thanks!
HTC_034 and software number 2.33.401.19
Hi,
I do have exactly the same issue on an untouched U11 single Sim. HTC support is not able to help me.
Current software version is 2.33.161.11 of a German Vodafone Rom with CID VODAP102.
So I am desperately looking for OTA to from 2.33.161.11 to 2.33.161.12 and then to 3.36.161.1 or a RUU for 3.36.161.1.
Any help is more than welcome.
@breno_campolina: have you tried to clear the cache of the those two system apps: update and download manager (Apps -> 3 point menu -> show system apps)? You might also want to try to download the update within the safe mode. I have tried all of this without success.
Cheers
Elendiir
elendiir said:
Hi,
I do have exactly the same issue on an untouched U11 single Sim. HTC support is not able to help me.
Current software version is 2.33.161.11 of a German Vodafone Rom with CID VODAP102.
So I am desperately looking for OTA to from 2.33.161.11 to 2.33.161.12 and then to 3.36.161.1 or a RUU for 3.36.161.1.
Any help is more than welcome.
@breno_campolina: have you tried to clear the cache of the those two system apps: update and download manager (Apps -> 3 point menu -> show system apps)? You might also want to try to download the update within the safe mode. I have tried all of this without success.
Cheers
Elendiir
Click to expand...
Click to collapse
Mine is also untouched and it is dual sim.
Did all this steps with them, did a factory reset too.
After this I think I`m done with them.... tired to be fobbed off
breno_campolina said:
Thanks!
HTC_034 and software number 2.33.401.19
Click to expand...
Click to collapse
Dual SIM right ? If yes, backup your data to your PC and flash this RUU in order to get a fresh start and from there use the Software Update check in Settings to upgrade to Pie.
https://androidfilehost.com/?fid=673956719939818418
To flash the RUU, the easiest way is to put it in the root folder of a MicroSD card, put it in the u11, power off, boot to Download Mode with Vol Down + Power together and follow the simple instructions on the screen to flash the RUU.
htc_one_mini_m4 said:
Dual SIM right ? If yes, backup your data to your PC and flash this RUU in order to get a fresh start and from there use the Software Update check in Settings to upgrade to Pie.
https://androidfilehost.com/?fid=673956719939818418
To flash the RUU, the easiest way is to put it in the root folder of a MicroSD card, put it in the u11, power off, boot to Download Mode with Vol Down + Power together and follow the simple instructions on the screen to flash the RUU.
Click to expand...
Click to collapse
Thanks!! I will try it tonight and come back to you!
htc_one_mini_m4 said:
Dual SIM right ? If yes, backup your data to your PC and flash this RUU in order to get a fresh start and from there use the Software Update check in Settings to upgrade to Pie.
https://androidfilehost.com/?fid=673956719939818418
To flash the RUU, the easiest way is to put it in the root folder of a MicroSD card, put it in the u11, power off, boot to Download Mode with Vol Down + Power together and follow the simple instructions on the screen to flash the RUU.
Click to expand...
Click to collapse
@htc_one_mini_m4 just put it on the sd card and boot on download mode, but it didn't do anything. Could explain me how to do it, please?
Sorry about the noob question.
breno_campolina said:
@htc_one_mini_m4 just put it on the sd card and boot on download mode, but it didn't do anything. Could explain me how to do it, please?
Sorry about the noob question.
Click to expand...
Click to collapse
Sure,
Here are the necessary steps.
Firstly, rename the file you downloaded to 2PZCIMG.zip
Reboot to download mode by powering up the phone with the Vol Down + Power button together.
Once it has loaded it will ask you if you want to perform flash RUU, just press the Volume Up button once to do so.
Wait, keep looking at your phone's screen.
It will reboot when finished, be patient while the flash is ongoing, and if it gets stuck on a black screen, DO NOT do anything, it will take some time until it reboots.
htc_one_mini_m4 said:
Sure,
Here are the necessary steps.
Firstly, rename the file you downloaded to 2PZCIMG.zip
Reboot to download mode by powering up the phone with the Vol Down + Power button together.
Once it has loaded it will ask you if you want to perform flash RUU, just press the Volume Up button once to do so.
Wait, keep looking at your phone's screen.
It will reboot when finished, be patient while the flash is ongoing, and if it gets stuck on a black screen, DO NOT do anything, it will take some time until it reboots.
Click to expand...
Click to collapse
Just did it and rename the file as you mentioned. It appears on the top htc download mode, but it didn't do anything.
can you post a screenshot ( photo ) of your phone at that screen ?
htc_one_mini_m4 said:
can you post a screenshot ( photo ) of your phone at that screen ?
Click to expand...
Click to collapse
Find it attached
Have you formatted your SD Card on your phone ?
And placed the renamed zip file in the main ( root ) folder of the SD Card ?
Follow this video guide, it's good
https://www.youtube.com/watch?v=1ACU3RGm9YI
Yes I did it.
Please check the file attached.
breno_campolina said:
Yes I did it.
Please check the file attached.
Click to expand...
Click to collapse
Just take out one ".zip" here
Once you remove the extra .zip it should do fine
htc_one_mini_m4 said:
Once you remove the extra .zip it should do fine
Click to expand...
Click to collapse
JUST GOT IT!! Thank you so much for your patience ))!
breno_campolina said:
JUST GOT IT!! Thank you so much for your patience ))!
Click to expand...
Click to collapse
You're welcome.
Now you'll be able to find the OTA updates via the Settings => About => Software Updates menu
Let us know if you succeeded in getting to Pie finally
htc_one_mini_m4 said:
You're welcome.
Now you'll be able to find the OTA updates via the Settings => About => Software Updates menu
Let us know if you succeeded in getting to Pie finally
Click to expand...
Click to collapse
Yes!!! Now getting used to android 9.0 :laugh::laugh:
Thank you!!!
Really sorry to just drop this here but I can't find what I need...please push me in the right direction. I have HTC U11 Unlocked, S-ON, I was using TWRP and Magisk for the longest time and fine. I'm afraid based on my latest user expriences with my phone I need OTA badly to get up to speed. Obviously I can't take it, the download gets corrupted. I am back to stock recovery but still rooted. Software Number 2.42.617.7, Android version 8.0. I did nothing but unlock and Magisk to this system since I got it in 2017. Please help me acquire the OTA and apply it or get to a state I can take it over the air.