Device:
http://www.gsmarena.com/karbonn_titanium_s5_plus-5925.php
I received a karbonn devices, which was soft bricked, and did not find much assistance by contacting them.
Here is the procedure to flashing the stock 4.2.2 firmware.
Download necessary files:
1. Firmware 4.2.009.P1.131118.7295MI01
2. Flashing tool: YGDP_Setup_V3.31_131028_02_Customer
3. Drivers if required
http://www.4shared.com/folder/zSTN87aV/Karboon_S5plus.html
1. Extract the zips
2. Install the flashing tool YGDP_Setup_V3.31_131028_02_Customer.exe 9make sure you right-click and grant it administrator privilege)
3. Right-click and open as administrator the newly created YGDP icon in your desktop
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Password : 9527
4. Select [config] button
5.
5.1
(see pic below) Select your firmware file which should be:
Code:
4.2.009.P1.131118.7295MI01.CPB
(note that it should end with CPB extension)
5.2
(see pic below) select customer as 7295MI01
6. Press [APPLY]
7. Select [START]
8. Connect your phone without the battery
Now the update procedure would start and when it is complete without errors disconnect, insert battery and boot your devices.
If it encounters any problem repeat the process.
Rooting:
http://forum.xda-developers.com/showthread.php?t=2572238
If that procedure fails you could use MTK rooter.
dogmatism said:
Device:
http://www.gsmarena.com/karbonn_titanium_s5_plus-5925.php
I received a karbonn devices, which was soft bricked, and did not find much assistance by contacting them.
Here is the procedure to flashing the stock 4.2.2 firmware.
Download necessary files:
1. Firmware 4.2.009.P1.131118.7295MI01
2. Flashing tool: YGDP_Setup_V3.31_131028_02_Customer
3. Drivers if required
http://www.4shared.com/folder/zSTN87aV/Karboon_S5plus.html
1. Extract the zips
2. Install the flashing tool YGDP_Setup_V3.31_131028_02_Customer.exe 9make sure you right-click and grant it administrator privilege)
3. Right-click and open as administrator the newly created YGDP icon in your desktop
Password : 9527
4. Select [config] button
5.
5.1
(see pic below) Select your firmware file which should be:
Code:
4.2.009.P1.131118.7295MI01.CPB
(note that it should end with CPB extension)
5.2
(see pic below) select customer as 7295MI01
6. Press [APPLY]
7. Select [START]
8. Connect your phone without the battery
Now the update procedure would start and when it is complete without errors disconnect, insert battery and boot your devices.
If it encounters any problem repeat the process.
Rooting:
http://forum.xda-developers.com/showthread.php?t=2572238
If that procedure fails you could use MTK rooter.
Click to expand...
Click to collapse
I have followed your instructions to the word. The YGDP download program keeps getting stuck after pressing 'Apply' after selecting the CPB file and version.
Moreover, the drivers that you have given are ADB drivers. I have installed them prior to all this. But my s5+ still doesn't get detected after I connect it to my PC without the battery. It says the driver installation failed. I forgot what was the device name that was being shown.
Could you please help me out. I have accidentally deleted certain system applications and need to get them back. Thanks.
The problem seems to be about drivers, if your phone is not identified, it wont flash, as i have installed a lot of drivers, my devices was detected automatically,
also make sure opened the program with admin rights.
As I do not have the phone with me, I could not do a trouble shoot with you, try to go to device manager and update drivers manually from local folder.
dogmatism said:
The problem seems to be about drivers, if your phone is not identified, it wont flash, as i have installed a lot of drivers, my devices was detected automatically,
also make sure opened the program with admin rights.
As I do not have the phone with me, I could not do a trouble shoot with you, try to go to device manager and update drivers manually from local folder.
Click to expand...
Click to collapse
thanks. will try that. But apart from that the flashing program has an issue as well. I'm running it on a 64 bit win 7 machine and I'm opening it with admin rights as well. also I need to open it in compatibility mode for windows XP. after hitting apply on the ROM selection screen it freezes. I guess that has nothing to do with the drivers as the phone isn't even connected yet.
any idea what's causing this?
Thanks for such an informative tutorial. I have this phone. From where can I download Custom ROMs like Cyanogenmod for it? Btw, are you getting poor camera quality by any chance?
Hats off sir
Thanks Sir Thank You Very Very Much You Save My Money! Thanks sir thank you!
ROM
when will we get kitkat ROM for titanium s5 plus
dogmatism said:
Device:
http://www.gsmarena.com/karbonn_titanium_s5_plus-5925.php
I received a karbonn devices, which was soft bricked, and did not find much assistance by contacting them.
Here is the procedure to flashing the stock 4.2.2 firmware.
Download necessary files:
1. Firmware 4.2.009.P1.131118.7295MI01
2. Flashing tool: YGDP_Setup_V3.31_131028_02_Customer
3. Drivers if required
http://www.4shared.com/folder/zSTN87aV/Karboon_S5plus.html
1. Extract the zips
2. Install the flashing tool YGDP_Setup_V3.31_131028_02_Customer.exe 9make sure you right-click and grant it administrator privilege)
3. Right-click and open as administrator the newly created YGDP icon in your desktop
Password : 9527
4. Select [config] button
5.
5.1
(see pic below) Select your firmware file which should be:
Code:
4.2.009.P1.131118.7295MI01.CPB
(note that it should end with CPB extension)
5.2
(see pic below) select customer as 7295MI01
6. Press [APPLY]
7. Select [START]
8. Connect your phone without the battery
Now the update procedure would start and when it is complete without errors disconnect, insert battery and boot your devices.
If it encounters any problem repeat the process.
Rooting:
http://forum.xda-developers.com/showthread.php?t=2572238
If that procedure fails you could use MTK rooter.
Click to expand...
Click to collapse
hello frnd i have spice coolpad 2 mi 496 model. the ygdp software is compatible with this device. my question is only that if my device will brick in future than can i fix it with this software i have both ygdp software as well stock rom of my device in cpb plz tell me
karbonn titanium x stock rom
please give me the karbonn titanium x stock rom and recoveary also...:crying:
Help !!! Boot problem of karbonn titanium s5 plus
dogmatism said:
Device:
http://www.gsmarena.com/karbonn_titanium_s5_plus-5925.php
I received a karbonn devices, which was soft bricked, and did not find much assistance by contacting them.
Here is the procedure to flashing the stock 4.2.2 firmware.
Download necessary files:
1. Firmware 4.2.009.P1.131118.7295MI01
2. Flashing tool: YGDP_Setup_V3.31_131028_02_Customer
3. Drivers if required
http://www.4shared.com/folder/zSTN87aV/Karboon_S5plus.html
1. Extract the zips
2. Install the flashing tool YGDP_Setup_V3.31_131028_02_Customer.exe 9make sure you right-click and grant it administrator privilege)
3. Right-click and open as administrator the newly created YGDP icon in your desktop
Password : 9527
4. Select [config] button
5.
5.1
(see pic below) Select your firmware file which should be:
Code:
4.2.009.P1.131118.7295MI01.CPB
(note that it should end with CPB extension)
5.2
(see pic below) select customer as 7295MI01
6. Press [APPLY]
7. Select [START]
8. Connect your phone without the battery
Now the update procedure would start and when it is complete without errors disconnect, insert battery and boot your devices.
If it encounters any problem repeat the process.
Rooting:
http://forum.xda-developers.com/showthread.php?t=2572238
If that procedure fails you could use MTK rooter.
Click to expand...
Click to collapse
This is what happened.....
I um... somehow changed the fonts of my android system to segoe ui through rom toolkit lite... rebooted it.......
now, i'm only able to boot into recovery..... i.e. when i try to boot normally, it just shows the loading screen forever..
i have android system recovery 3e in my karbonn titanium s5 plus...
tried the above method........... but no use.... it kept showing some checksum error.....
i cant use adb too except for adb sideload.... which i cant as i have damn less internal memory free space
what do i do ?
p.s send any solution to this to my email :
[email protected]
ps. if possible, could you send me some roms and recoveries compatible with this phone ??? (Karbonn Titanium S5 Plus)
i searched the internet and found nothing.... if anybody happens to stumble over something for this, please send it to me. thanks in advance.
Unhappy karbonn titanium x stock rom
please give me the karbonn titanium x stock rom and recoveary also...
Click to expand...
Click to collapse
check for your device model from coolpad and download the rom from coolpad romer accordingly...
check for the roms from coolpad romer in google drive
edit 2:
thanks to Mr Shrikar Galgali who sent me the rom from coolpad romer
use this link for the original rom ....
https://tr.im/20c3b
he also sent me a few other ROMs..
Here are links for ROMs compatible with karbonn titanium s5 plus :
Sony xperia z:
https://www.dropbox.com/s/e8sq7s60de82mvl/Xperia_Z_Karbonn_S5_Plus.zip
Sony xperia z v2:
https://tr.im/ca47d
Miui :
http://www.needrom.com/wp-content/uploads/2014/03/miui_7295c_4.3.7_2c5837e511_4.2.zip
( to download this, you need to log in to needrom.com first )
Also visit these pages for more help...
https://www.facebook.com/karbonns5plus
https://www.facebook.com/karbonnroms
Note : The above posted links for roms are not tried and tested ! Be Careful !
For some of the ROM downloads, you need to log into the respective sites...
Eg: You need to log in to your google account to download the Samsung Galaxy S5 ROM and the Xperia Z v2 ROM
Thanks mainly to the thunderboys team and all other developers of the respective ROMs whom I haven't mentioned.
edit 3:
Yep. My phone is fixed....
Had to go to the service center though....
anyway.....
For all those who damaged their System UI:
Here are the SystemUI.apk and the SystemUI.odex files:
http://www.4shared.com/rar/cyMk4Dyuba/Karbonn_Titanium_S5_Plus_Syste.html
Hope it helps !
ClockWorkMod recovery for Karbonn Titanium S5 Plus :
Here is the cwmrecovery.img file of karbonn titanium s5 plus, for all those who might need it.
tr.im/RWOT
( beware, the above link is not tried and tested ! )
hope it helps !
edit 4:
The MIUI ROM and the Sony Xperia v2 ROM work properly. For people who have boot issues, doing a full data wipe/factory reset through the recovery will solve that problem... MIUI is pre rooted, but chainfire's SuperSU app is not installed and there is no keyboard app. The Sony Xperia v2 ROM has SuperSU installed and works properly. However, a high amount of patience is needed to wait for the ROMs to boot up...
As mentioned by cybercrawler, the internal/external swap supposedly works, and appears to be already applied in these ROMs... so, if you are going to flash a new ROM, you had better undo this change...
The clockworkmod recovery file works too, as seen in the screenshots uploaded by cybercrawler... thanks to him for testing that out.
I shall be uploading some screenshots of these in a few days. Both the ROMs run Android Jelly Bean 4.2.2, and the MIUI ROM has a update scheduler app, so I'm guessing it can be updated to 4.4 Kitkat. Anyway... if anybody knows how to bypass Dropbox Error 509 ( This account's public links are generating too much traffic and are temporarily disabled ), please download the Xperia Z v1 ROM and upload it to Google Drive... I shall be uploading the MIUI v5 ROM to Google Drive within the next few weeks...
karbonn titanium x
please help me how to instal karbonn titanium x stock rom...?
cen u please give me a download link...?
uinod3 said:
please help me how to instal karbonn titanium x stock rom...?
cen u please give me a download link...?
Click to expand...
Click to collapse
have you installed some custom recovery on your phone? I also own titanium x and was wondering if you are able to do that. I can share the stock rom if you still need it.
i guess so...
Invincibl3 said:
have you installed some custom recovery on your phone? I also own titanium x and was wondering if you are able to do that. I can share the stock rom if you still need it.
Click to expand...
Click to collapse
well, if you have any custom recovery images, you could do it through fastboot ( fastboot flash recovery nameofrecovery.img )
else, if you have flashable recovery zip files, you could do it through adb sideload in recovery...
try twrp recovery... touch based recoveries are good for karbonn devices
take a backup of your current rom ( and recovery if possible ) first...
make sure that you know any karbonn service centre near you who can fix your phone if it gets bricked.
( i'm telling you so because when my karbonn titanium s5 plus bricked, it took a week and a half to get the phone serviced at the service centre. )
find some roms compatible with your device, and make sure you dont install new fonts or anything like that. rooting is okay...
try this link for karbonn roms
"goo .gl/ p0QK1m"
(remove the quotes and no spaces)
oh, and does anybody have an idea of creating a one-for-all rom that would work on any android device, be it tablet or smartphone ?
it could have the most basic features and could be based on android 4.4 kitkat....
it's purpose is mainly for backup... just in case no other rom is compatible with a certain phone and you can't find the stock rom anywhere...
please reply to my gmail id if you have any idea of doing so....
rajju 3004 @ gmail . com
(remove the quotes and no spaces)
Note: Never ever change or add any new fonts to a Karbonn device...
can u give me link of custom roms for titanium s5 plus.
read my post!
anmolmatharu said:
can u give me link of custom roms for titanium s5 plus.
Click to expand...
Click to collapse
see my post on the first page !
Invincibl3 said:
have you installed some custom recovery on your phone? I also own titanium x and was wondering if you are able to do that. I can share the stock rom if you still need it.
Click to expand...
Click to collapse
yes i have a custom recovery in my phone .....
please provide stock rom or kitkat rom for karbonn titanium x mobile....
titanium x stock rom
uinod3 said:
yes i have a custom recovery in my phone .....
please provide stock rom or kitkat rom for karbonn titanium x mobile....
Click to expand...
Click to collapse
the below link is for the titanium x stock rom of android jelly bean 4.2.2
" goo. gl / 1Epkmz "
(remove the quotes and no spaces)
hope it helps !
rjt.rockx said:
the below link is for the titanium x stock rom of android jelly bean 4.2.2
" goo. gl / 1Epkmz "
(remove the quotes and no spaces)
hope it helps !
Click to expand...
Click to collapse
it is not a stock rom....:
and the proseser given in link "goo.gl/1Epkmz" was not working and it was not downloading.....
please help me....:crying:
try this
uinod3 said:
it is not a stock rom....:
and the proseser given in link "goo.gl/1Epkmz" was not working and it was not downloading.....
please help me....:crying:
Click to expand...
Click to collapse
try this :
tr.im/MMLf
it is not a rom which can be flashed through recovery...
see this for instructions
tr.im/MMUk
hope it helps !
Scatter file.
cybercrawler had asked for the scatter file of Karbonn titanium s5 plus.
well, here it is, attached to this post.
Related
I no longer have this phone (GiONEE Dream_D1), I'm also going to stay away from Mediatek SoCs.
No more support for this device in this thread. If anyone wants to take over, please do. Thanks everyone who participated and encouraged me.
Link to the stock deodexed rom available in post #2 below.
For increasing the internal storage to 2GB from 1 GB, follow the instructions by @RickyGoldsmith here http://forum.xda-developers.com/showpost.php?p=41966897&postcount=3
-------------------------------------------------------------------------------------------------------------------------------------
Stock Factory ROM root instructions:
Download the zip file named motochopper.zip from the First Post of this thread here: http://forum.xda-developers.com/showthread.php?p=40747604
Thanks and Credits to djrbliss
YOU ARE DOING THIS AT YOUR OWN RISK.
Instructions:
Extract the entire contents of the zip file.
If you are using Windows, ensure you have installed the latest MediaTek USB drivers available for your phone. Download link for the MediaTek drivers here: http://goo.gl/A7gnp
Ensure USB Debugging mode is enabled on your device.
Connect your device to your PC via USB.
Run run.bat from the extracted folder.
Follow the instructions on screen, when everything is done, the phone will reboot.
Voila! Now your Gionee Dream D1/GN878 will be rooted.
CWM Recovery for Gionee Dream D1/GN878
Steps to install CWM recovery: YOU ARE DOING THIS AT YOUR OWN RISK.
1. Install the MTK USB Drivers for the phone. If you had followed the above steps to root then You have the drivers installed.
2. Download the SP Flash tool, with the scatter file and the recovery.img. Download link here: http://goo.gl/SD9kh
CWM Version 6 available here http://forum.xda-developers.com/showthread.php?p=43039475#post43039475 thanks to @deepak2111
3. Extract the zip file and run the Flash_tool.exe
Leave all the options as default, do not tinker with any settings, except pointing to the correct scatter file.
4. The scatter file and the recovery.img are placed in a folder named DreamD1 in the extracted folder.
In the Flash tool, click on scatter-loading button and select the file named MT6589_Android_scatter_emmc_PMT.txt
The recovery will be auto selected as shown in the image below: DO NOT CHECK ANY OTHER CHECKBOXES.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
5. Click on the Download button. DO NOT CLICK ON Firmware->Upgrade Button, it will brick your Phone
6. Remove the phone from the USB cable
7. Switch off the phone, wait till you feel the vibration. Wait for another 30 seconds
8. Now plug in the phone to the USB cable without turning on the Phone.
As soon as the phone is detected, the recovery image will be installed.
Voila!, Now you phone has CWM recovery installed.
After the recovery installation, remove the phone from the USB Cable.
To go to Recovery Mode: KeepPressing Power + Volume Up Keys. You should now be greeted with CWM recovery menu.
Please HIT the Thanks button if you feel I deserve it.
Note: Just found out that the Chinese Model number for Dream D1 is GN878
Hybrid Stock ROM De-Odexed, Zipaligned rooted with busybox - best of Primo-X1 and Dream D1
Kernel aka boot.img is included in the rom zip as we now have the MTK6589 SoC sources.
Copy the downloaded Zip to External SD Card.
Reboot to CWM Recovery
Do Factory reset.
Flash this using CWM Recovery.
Download Link:: https://copy.com/frhv3
Known Bugs:
Selecting Wallpaper from Settings->Display->Wallpaper FCs.
Please let me know, if you come across any bugs here in this thread.
---------------------------------------------------------------------------------------------------------------------------------------------------------------------
GiONEE Dream_D1 Stock deodexed ROM with root and busybox.
Copy the downloaded Zip to External SD Card.
Reboot to CWM Recovery
Do Factory reset.
Flash this using CWM Recovery.
Download Link:: https://copy.com/yRrfRMDNBE4A
MT6589 SoC Kernel source: https://github.com/varunchitre15/MT6589_kernel_source
Credits to varunchitre15 for the kernel sources.
MIUI
How about porting MIUI to start with?
I am already running MIUI Home Launcher and it is a breeze. Do you have any experience with porting ?
I looked at: http://forum.xda-developers.com/showthread.php?t=1827256 and it looks straight forward. What I am not sure is how much these applications depend on the underneath framework.. I mean, If I take all these apk and libraries, will it work on this stock Gionee Dream D1 ROM ?
somberi said:
I'm also working on porting the CWM recovery to Gionee Dream D1. Once that is completed I shall share it here.
Click to expand...
Click to collapse
waiting for CWM ,have to get rid of this rom,every hd games opens after 10minutes
million thanks
I cant believe my eyes
I am going to root that right now, but first i am going to thank you
Great job and we will wait for your new roms
thanks
RickyGoldsmith said:
How about porting MIUI to start with?
I am already running MIUI Home Launcher and it is a breeze. Do you have any experience with porting ?
I looked at: http://forum.xda-developers.com/showthread.php?t=1827256 and it looks straight forward. What I am not sure is how much these applications depend on the underneath framework.. I mean, If I take all these apk and libraries, will it work on this stock Gionee Dream D1 ROM ?
Click to expand...
Click to collapse
I would wait for a CWM recovery / Factory Stock rom for Gionee Dream D1, before I start to working on ROM ports. Anyways good to see interest for this device.
protocolt fault
I am getting the protocol fault, waiting for device.
Any idea the cause for that?
somberi said:
I would wait for a CWM recovery / Factory Stock rom for Gionee Dream D1, before I start to working on ROM ports. Anyways good to see interest for this device.
Click to expand...
Click to collapse
How do you intend to get the Factory Stock ROM? Rip it from the device?
I am currently trying to play with the CWM process. Will update here how it goes...
ashishsoft said:
I am getting the protocol fault, waiting for device.
Any idea the cause for that?
Click to expand...
Click to collapse
Did you install the MediaTek drivers from the link above? Make sure you dont have the phone connected in the PDANet+ (Right click on the System Tray icon and click on disconnect. Also make sure you have USB debug enabled, under Settings->Developer Options.
If all the above fail try restarting the system and try to connect the phone to a different USB port on your computer.
let me know the results.
RickyGoldsmith said:
How do you intend to get the Factory Stock ROM? Rip it from the device?
I am currently trying to play with the CWM process. Will update here how it goes...
Click to expand...
Click to collapse
Currently looking at various Chinese forums to get a proper rom backup tool for MediaTek based devices. Also have contacted Gionee India asking them to release the Factory Stock ROM and the flashtool for the device. Micromax, Lava and many other manufactures give the Stock ROM for download.
At work now and do not have access to any of the resources here..
rooted it
sorry it got that rooted!
yeah!
now waiting for the ROMS
thanks
ashishsoft said:
sorry it got that rooted!
yeah!
now waiting for the ROMS
thanks
Click to expand...
Click to collapse
Nice to know
I am your fan somberi
You are a master, !
Great job done and keep that up
:angel:
somberi said:
I would wait for a CWM recovery / Factory Stock rom for Gionee Dream D1, before I start to working on ROM ports. Anyways good to see interest for this device.
Click to expand...
Click to collapse
Are you able to get the boot.img image dump?
MtkTools and others create a file which is just binary data.
our stock recovery is useless...pls gv us cwm and unroot.zip too....for safety...
Sent from my Dream_D1 using xda app-developers app
---------- Post added at 01:01 PM ---------- Previous post was at 12:48 PM ----------
somberi said:
Download the zip file named motochopper.zip from the First Post of this thread here: http://forum.xda-developers.com/showthread.php?p=40747604
Thanks and Credits to djrbliss
You are performing this at your OWN RISK!
Instructions:
Extract the entire contents of the zip file.
If you are using Windows, ensure you have installed the latest MediaTek USB drivers available for your phone. Download link for the MediaTek drivers here: http://goo.gl/A7gnp
Ensure USB Debugging mode is enabled on your device.
Connect your device to your PC via USB.
Run run.bat from the extracted folder.
Follow the instructions on screen, when everything is done, the phone will reboot.
Voila! Now your Gionee Dream D1 will be rooted.
Click to expand...
Click to collapse
i hv sucsfuly rooted my dvice...waiting for cwm n unroot...
Sent from my Dream_D1 using xda app-developers app
RickyGoldsmith said:
Are you able to get the boot.img image dump?
MtkTools and others create a file which is just binary data.
Click to expand...
Click to collapse
Could not get time to investigate, too much work.. Will have to spend some time this weekend.
how to install CWM recovery/4ext
hi there
after rooting the device, i have been trying to get in the recovery, i tried using CWM and 4ext both
but everytime i try go to recovery it only shows me default factory mode, that is it. nothing else
can someone tell me why and guide me
thanks
Finally managed to get CWM recovery ported to Gionee Dream D1. Testing in progress.
Works great.
The External SD card is detected.
Did a nandroid backup, restored the back up without any problems.
Did a Factory reset and worked great.
somberi said:
Finally managed to get CWM recovery ported to Gionee Dream D1. Testing in progress.
Works great.
The External SD card is detected.
Did a nandroid backup, restored the back up without any problems.
Did a Factory reset and worked great.
Click to expand...
Click to collapse
That's great news. Thanks
On my windows 7 ThinkPad, it has never been able to detect the phone over the serial console. Perhaps I'll try it on someone else's box.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Technical Specs
[*]Google it before posting here.
[*]Please post any guides and/or tutorials directly onto the forum, rather than links, otherwise this thread will be closed by the Moderator.
Click to expand...
Click to collapse
Rooting for 8GB Version
Procedure:
1. Download the Framaroot application and transfer it to SD card
2. Now go to Settings>Security and put check mark on Unknown Soruces
3. Now use file manager and browse to the location where you have placed Framaroot Application
4. Install it and open it. Now Select "Install SuperSU" and hit Boromir.
5. Now go to Play Store and search for Super User and install it after opening it might ask to update SU.bin, hit yes and then "Normal"
6. Reboot your Device.
[ROMs]
Please do not flash the firmware that is not meant for your phone. Flash only 4gb to 4gb and 8Gb to 8Gb
Auxus Nuclea N1 Stock Firmware
NEW
Final Version - 11-Dec-2013 - [Flash with SPFlash Tools]
Click to expand...
Click to collapse
OLD ROMs
Firmware Update (Intermediate V1) 18-Nov-/2013 [Flash with spflash Tools]
NucleaN1_FirmwareUpdate_V1_CWM.zip
Click Here - - [09/Sep/2013] [Flash with SPFlash Tools]
CWM Zip Download from herehttp://d-h.st/b3r
8GB version -
Click Here - [Flash with SPFlash Tools]
Custom ROMs
Click HERE
How to Flash Stock ROM using SP Flash Tools?
1) Unzip the ROM folder
2) Install the drivers and open SP Flash Tools..
Check the below post with images, if you are not sure whether drivers are installed or not.
If you face this problem, then try Firmware upgrade and connect the phone..
You can now safely disconnect your phone and turn it on. The process ends here.
FLASHING PATCH using SP Flash Tool(Single Files)
1)Select Android Scatter File .txt ....
2)Uncheck all files from the below box....
3)Select the correct file you want Flash by clicking it....
4)Click Download button on SP tool.... **"Dont click Firmware Upgrade"
5)A box asks to confirm it...Click Yes...
6)Connect Phone without the battery...
7)It will get Flashed...[/COLOR]
[Recovery]
1) Nuclea N1 Stock Recovery Click Here
2) TWRP Recovery- Click HereThanks to Kumar abhishek
3) CWMRecovery 6.0.3.3 Click Here or Click Here Thanks to C3C076
Procedure to Flash Recovery.
1) Download Mobile uncle tools from play store
2) Place the downloaded recovery.img in your sdcard
3) Open Mobile uncle tools
4) Select 'update recovery' and Click on the recovery.img
5) Reboot
adb method: For advance users:
---------------------------------------------------
Make sure you have all the drivers for your phone installed on your computer.
Make sure you have USB Debugging enabled, Install from Unknown Sources is enabled and device is detected in ADB run this command:
Code:
adb devices
Download the CWM Recovery
Press SHIFT key + Right mouse click in the folder where the file is located and select Open Command from Here.
Now, in the command prompt do the following:
a. Reboot into Bootloader mode. Use command:
Code:
adb reboot bootloader
b. Device will reboot and display logo. (check if device is in bootloader mode by running command:
Code:
fastboot devices
. If you see a device connected then you have successfully rebooted into fastboot mode.
c. Now, run this command:
Code:
fastboot flash recovery recovery.img
(This will flash the CWM recovery image to the device).
d. Once successful, reboot the device using this command:
Code:
fastboot reboot
.
How to Backup ur complete ROM
1. In CWM Recovery mode, select Backup and Restore
2. Select Backup
3. Wait till it finishes (May take upto 10 minutes)
How to restore ur backed up ROM from SD card
1. Go to CWM Recovery, select backup and restore
2. Select Restore
3. select the folder in date format (Folder name indicates the time and date when ur backup was created}
4. Wait till it finishes (May take upto 10-15 minutes)
Special Guides for Newbies to get Started
Everything you need to know about Clockworkmod Recovery
How to setup ADB and Fastboot properly
5 Things Every Android user should do
24 Apps Every Android User Must Install
5 Things to know before performing any Android tweak
Thanks to Driodiser
HIT THANKS PLEASE BECAUSE IT WONT COST ANY :angel:
Extend your storage on Nuclea N1
[Extend your storage on Nuclea N1] - Thanks to @kailashnj
Follow the instructions in the post HERE
How to enter into Recovery - Nuclea N1 :-
Code:
[LIST=1]
[*]Turn OFF your phone.
[*]Press & hold Vol(+) button and Power button for 12 seconds.
[B]Stock Recovery[/B]
[*]You will see a laid-down Android symbol with 'No command' message below it. Press the power button once.
[*]You will enter into menu 'Android System Recovery'
[*]Press Vol(-) to roll over options.
[*]Press Vol(+) button to select.
[*]DONE!
[/LIST]
Another options if you are facing trouble going to recovery:
Code:
1. Install Mobile Uncle tool
2. Reboot recovery.
MTK6589 Drivers
Universal Pdanet drivers Click Here
Follow this guide Here
Tools
MTK Android PC Sync Tool V2.1233.1 Click Here
SN_Write_tool_exe_v2.1132.0.rar - 8.27 MB
Guide Here
Driver_Auto_Installer_v1.1236.00 Click here
Meta-Mode is very useful if device fails to get detected by PC under normal Conditions.....To make device fall to Meta-Mode,just do these :
1) Start SP Tool on PC..
2) Now run SP Tool with "Firmware Upgrade/Download"
3) Switch OFF Phone..
4) Remove Battery..
5) Connect mobile to PC while holding Volume + button [WITHOUT BATTERY]..
6) Flashing will be started
7) Hold the button till flashing completes...
After 100% Flash,Release Button..
9) Insert Battery..
10) Start Device.
Click to expand...
Click to collapse
How to dump stock recovery image using SP Flash Tool
1) Download and install USB VCOM Driver
2) Download, extract and launch SP Flash Tool
3) Use "Scatter-loading" button to load attached scatter file: MT6589_Android_scatter_emmc.txt
4) Download stock recovery image and place inside the ROM folder. Then select only RECOVERY.
5) Turn off your phone. Make sure USB cable is unplugged. Wait until vibrator indicates it's turned off
6) Click Download button in SP Flash tool, confirm warning complaining about not all files being selected
7) Connect your phone and wait for the flash process to finish (indicated by window with green circle)
8) Unplug USB cable. Hold down Volume+ while turning your phone on to boot into recovery
Click to expand...
Click to collapse
Backing up your IMEI
Different Methods are available for this.
1) Use any RootExplorer to copy file /data/nvram/md/NVRAM/NVD_IMEI/MPOB_001 to your external SD card. (or if that folder does not exists, try /nvram/md/NVRAM/NVD_IMEI/MPOB_001). It is good to backup the entire folder /data/nvram/md/NVRAM.
2) Back up using Mobile Uncle utility. Click on Mobileuncle Tools --> Click IMEI Backup Restore (MTK) --> Backup/Restore
Restore your IMEI
Code:
1- Open Mobile Uncle Tools.
2- Goto Engineer Mode
3- Select Engineer mode[MTK]
4- Under Connectivity Tab go to CDS information
5- Select Radio Information
6- Select Phone1 (for the first imei)
7- at the top there is a command line which begins “AT+” just type there “AT +EGMR=1,7,”IMEI_1? (instead of IMEI_1 put your first imei number)
8- hit send command
9- You will / may get a confirmation that "sent to mSend".
10-Now come back and select “Phone2?
11-at the top there is a command line which begins “AT+” just type there “AT +EGMR=1,10,”IMEI_2? (instead of IMEI_2 put your second imei number)
12-Then just reboot the phone.
13- Dial ” *#06#” to Check Imei.
Factory ROM Backup for MT65xx via MTK Droid Root & Tools For BackUp & Unbrick
It's tested and working...
How to install ADB USB driver in window 7
use this method also in window xp,if any driver not install
Google USB Driver Rev 7 ( ADB driver )
inside three dll file driver
1-WdfCoInstaller01009.dll
2-winusbcoinstaller2.dll
3-WUDFUpdate_01009.dll
link
Click Here
Before use it is necessary to check that:
adb drivers are installed. Check device manager--> unknown devices. ADB Drivers attached.
Now the Tool
Credits: umesh gaba
[MOD][4.1 4.2] Extend Phone Storage 1.5, 2.5GB A116 (Other MT6589 Devices on request)
[Solution] NVRAM WARNING: Err = 0x10
Download this zip Click Here
Prerequisites:
You have to backup IMEI of your phone (both sim slot).
Step 1 - Extract the WiFi Fix files and place them in a folder on your memory card
Step 2 - Open Root Explorer
Step 3 - Click on Mount R/W
Step 4 - Click on data
Step 5 - Scroll down to the folder named nvram
Step 6 - Open APCFG folder
Step 7 - Open APRDEB folder
Step 8 - Delete the WIFI and WIFI_CUSTOM files
Step 9 - Now copy/move the files on your sdcard to data/nvram/APCFG/APRDEB and Paste
Step 10 - After pasting both the files, close Root Explorer and REBOOT your phone.
Here is another method Click Here
The bad news is.
Vijay have u bot the mobile..
Sent from my AUXUS Nuclea N1 using xda app-developers app
can you provide a review of the phone?
akashavel said:
Vijay have u bot the mobile..
Sent from my AUXUS Nuclea N1 using xda app-developers app
Click to expand...
Click to collapse
Hello dude,
i have booked this phone, and i am seriously waiting for some reviews.
It would be great if there was a video review done by you on you tube or where ever you are comfy.
The specs are awesome but there are some negative opinions as well.
This would help.
Thanks
akashavel said:
Vijay have u bot the mobile..
Sent from my AUXUS Nuclea N1 using xda app-developers app
Click to expand...
Click to collapse
Yes, I am in batch II.
dhavalg said:
Hello dude,
i have booked this phone, and i am seriously waiting for some reviews.
It would be great if there was a video review done by you on you tube or where ever you are comfy.
The specs are awesome but there are some negative opinions as well.
This would help.
Thanks
Click to expand...
Click to collapse
videos posted by me..
https://www.youtube.com/user/akashavel/videos
also chk this fb page
https://www.facebook.com/groups/Ibe...39765010250/?ref=notif¬if_t=group_activity
Hi Guys,
Even I have bought this phone and awaiting delivery, I was promised by 4th Aug. Lets see. The specs of this phone seems to be great other than the 4GB storage. I hope that apps2sd works really fine and I am able to store all my game data on the SD card. Wanted to know more info of this phone and the rom.
Regards,
Kailash
can't decide what to buy
is the costumer service good...i am really thinking to buy this phone but this brand was never heard before by me.....
in ur opinion which phone would be better
1. canvas 4 (micromax)
2. auxus nuclea n1 (iberry)
3. Xolo play (XOLO)
Thanks...
akashavel said:
videos posted by me..
https://www.youtube.com/user/akashavel/videos
also chk this fb page
https://www.facebook.com/groups/Ibe...39765010250/?ref=notif¬if_t=group_activity
Click to expand...
Click to collapse
That was really helpful, but i hoped some words about the phone from your mouth as well.
Need some comparison too,
But any ways it was awesome....I am going to continue with my order, actually i was planning on cancelling it. But now not...
Thanks for the videos.
Hope we get roms for it as well.
:victory: Yesss... XDA Thread for Auxus Nuclea.. feeling exciting.. Best Wishes, Guy.. :good::good:
dhavalg said:
That was really helpful, but i hoped some words about the phone from your mouth as well.
Need some comparison too,
But any ways it was awesome....I am going to continue with my order, actually i was planning on cancelling it. But now not...
Thanks for the videos.
Hope we get roms for it as well.
Click to expand...
Click to collapse
only thing is RAM so many apps consumes more memory .waiting for tweaked ROM.other than that the phone is gud..
I prefer to use Titanium Backup to freeze unwanted app rather to uninstall.. this app will save lots of RAM..
without source kernals cant we install custom Roms or stock roms, iam newbie to these things, i have a doubt, i have seen so many custom ROMs for samsung devices that means have samsung provided the source kernals???? please reply any experts
Without kernel source who would buy this phone and on top of that its Chinese brand better buy micromax Indian brand.....
ashok20205 said:
without source kernals cant we install custom Roms or stock roms, iam newbie to these things, i have a doubt, i have seen so many custom ROMs for samsung devices that means have samsung provided the source kernals???? please reply any experts
Click to expand...
Click to collapse
Yes, We can install Custom ROMs (Themed ROMs or Ported ROMs). But, with kernel sources a lot of development can happen. :good:
akashavel said:
only thing is RAM so many apps consumes more memory .waiting for tweaked ROM.other than that the phone is gud..
Click to expand...
Click to collapse
No need to wait for a Custom ROM. You can try One-Power-guard app, Clean master and Greenify app's.
Chris s5830i said:
Without kernel source who would buy this phone and on top of that its Chinese brand better buy micromax Indian brand.....
Click to expand...
Click to collapse
This mobile is good at it price with the spec's. Even Micromax is not providing kernel sources. Also, compared to the support of Micromax, iBerry is doing best.
abhiek bist said:
is the costumer service good...i am really thinking to buy this phone but this brand was never heard before by me.....
in ur opinion which phone would be better
1. canvas 4 (micromax)
2. auxus nuclea n1 (iberry)
3. Xolo play (XOLO)
Click to expand...
Click to collapse
Check the facebook page. Then you can decide
Can you post link for CWM for nuclea N1
can you help me with the link for CWM
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Gionee Elife E3 is a Mobile made by a chinese Handset manufacturer Gionee , It is just 7.9mm thick and has a gorgeous display.
So in this Thread I will be discussing :-
READ AND FOLLOW THE WHOLE PROCEDURE..! ITS IMPORTANT
1. How to Root Gionee Elife E3
2. How to Flash CWM
3. Compatible Roms with Gionee Elife E3
4. How To Flash Custom Roms
5 . Difference Between Indian & Chinese Gionee Elife E3
6. Firmware You should Flash to install Custom Roms
Lets Start With - How to identify which Gionee Elife E3 Firmware You Are Currently Using .
Go into Setting >> System Update and Click on Update Firmware Button . If u notice anything there written in chinese or if u have the button of the System update in a circular Form then your elife e3 has the Chinese Firmware , otherwise u have The Indian Firmware :good:
Ok so now you identified which firmware u have. (Identifying which firmware u have will come in handy later on)
Lets Start Rooting of the Phone
ROOTING OF GIONEE ELIFE E3 (CHINESE AND INDIAN) -
STEPS - GO TO SETTING>> ABOUT PHONE
Repeatedly tap on Build Number (seven taps should do the trick) until you’re met with a message that reads: “you are now a developer!”
GO BACK TO SETTINGS
THEN TAP ON DEVELOPER OPTIONS
TICK MARK THE USB DEBUGGING OPTION
GO BACK TO SETTINGS
TAP ON SECURITY
TICK MARK THE OPTION "UNKNOWN SOURCES" AND CLICK "OK"
TAP THE HOME BUTTON NOW
:good:
INSTALLING THE USB DRIVERS BEFORE ROOTING -
YOU MUST HAVE TO INSTALL THE USB DRIVERS OF THE PHONE BEFORE ROOTING
SO DOWNLOAD THIS TOOL (PDANET)- http://pdanet.co/bin/PdaNetA4126.exe AND FOLLOW THE INSTRUCTIONS
INSTALL PDANET
FOLLOW THE PROCEDURE AND CLICK ON "OTHERS" OPTION IN THE PHONE SELECTION MENU
CONNECT YOUR GIONEE ELIFE E3 WHEN ASKED AND IT WILL AUTOMATICALLY INSTALL ALL DRIVERS :good:
Download MOTOCHOPPER (ROOTING TOOL) here:
http://vulnfactory.org/public/motochopper.zip
Instructions:
Extract the entire contents of the zip file.
Connect your device to your PC via USB. DO NOT TURN ON USB STORAGE ON YOUR GIONEE ELIFE E3...!!!!
If you are using Windows, navigate to the extracted directory and execute "run.bat". If you are using Linux or OS X, navigate to the extracted directory in a terminal and execute "./run.sh".
HIT ENTER
WAIT
Approve the ADB connection from your PC on your device. IF IT ASKS TO DO SO . DO NOT TURN ON USB STORAGE ON YOUR GIONEE ELIFE E3...!!!!
WAIT
HIT ENTER WHEN IT ASKS TO HIT ANY KEY
UR DEVICE WILL NOW REBOOT ON ITS OWN
AFTER REEBOOT YOU HAVE SUPERUSER INSTALLED,,!!
FLASHING THE CWM IF U HAVE INDIAN FIRMWARE -
Install "MOBILE UNCLE TOOL" FROM THE PLAY STORE
DOWNLOAD RECOVERY.IMG FROM PC - http://d-h.st/vcU
CONNECT PHONE TO PC VIA USB AND TURN ON USB STORAGE
COPY RECOVERY.IMG FILE TO THE ROOT OF INTERNAL SD CARD
DISCONNECT THE PHONE FROM PC
GO INTO MOBILE UNCLE TOOLS APP . GRANT IT SUPERUSER PERMISSION FOREVER
TAP ON RECOVERY UPDATE
SELECT THE "RECOVERY.IMG" FILE FROM INTERNAL SD AND FLASH IT
CLICK "OK" AND BOOT INTO RECOVERY "OK"
YOU ARE NOW IN THE CWM (CLOCKWORDMOD RECOVERY) VOLUME UP AND DOWN BUTTONS ACT AS UP AND DOWN (TO NAVIGATE)
AND POWER BUTTON ACT AS THE SELECTION BUTTON
CLICK ON REBOOT DEVICE OR REBOOT
AND THEN CLICK ON "YES" AND THEN "YES"
AFTER REBOOT YOU HAVE FLASHED UP THE CWM .. CONGRATS..! :good:
FLASHING THE CWM IF U HAVE CHINESE FIRMWARE -
CHINESE FIRMWARE'S DO NOT HAVE THE PLAYSTORE SO U WILL HAVE TO DOWNLOAD THE MOBILE UNCLE TOOLS SEPERATELY AND INSTALL THAT TO UR DEVICE , HERE'S THE LINK TO DOWNLOAD MOBILE UNCLE TOOLS - http://d-h.st/9Q8
AFTER U DONE INSTALLING
DOWNLOAD RECOVERY.IMG FROM PC - http://d-h.st/y4X (ITS THE RECOVERY OF BLU LIFE PLAY..IT WILL LATER HELP U FLASH UP ROMS)
CONNECT PHONE TO PC VIA USB AND TURN ON USB STORAGE
COPY RECOVERY.IMG FILE TO THE ROOT OF INTERNAL SD CARD
DISCONNECT THE PHONE FROM PC
GO INTO MOBILE UNCLE TOOLS APP . GRANT IT SUPERUSER PERMISSION FOREVER
TAP ON RECOVERY UPDATE
SELECT THE "RECOVERY.IMG" FILE FROM INTERNAL SD AND FLASH IT
CLICK "OK" AND BOOT INTO RECOVERY "OK"
YOU ARE NOW IN THE CWM (CLOCKWORDMOD RECOVERY) VOLUME UP AND DOWN BUTTONS ACT AS UP AND DOWN (TO NAVIGATE)
AND POWER BUTTON ACT AS THE SELECTION BUTTON
CLICK ON REBOOT DEVICE OR REBOOT
AND THEN CLICK ON "YES" AND THEN "YES"
AFTER REBOOT YOU HAVE FLASHED UP THE CWM .. CONGRATS..! :good:
MAKE A NADROID BACKUP FOR YOUR E3 BEFORE PROCEEDING (INDIAN AND CHINESE BOTH) , HERE'S HOW - http://www.youtube.com/watch?v=36cihz4l-vk
DO NOT RESTORE THIS BACKUP..!! ONLY MAKE A BACKUP
FLASHING UP CUSTOM ROMS AND AVAILABLE CUSTOM ROMS -
AVAILABLE CUSTOM ROMS FOR ELIFE E3 -
INFINITY HD
http://forum.xda-developers.com/showthread.php?p=44023789#post44023789
XPERIA HD
http://forum.xda-developers.com/showthread.php?p=44168616#post44168616
GamerzROM
http://forum.xda-developers.com/showthread.php?p=44168525
NOTE - IF U ARE USING THE INDIAN FIRMWARE .. U WILL NOT BE ABLE TO FLASH UP ROMS CURRENTLY .. SO U NEED TO FLASH UP THE CHINESE FIRMWARE TO YOUR GIONEE ELIFE E3
HERE'S THE CHINESE FIRMWARE -
ORIGINAL FIRMWIRE E3
Go with google translate here - http://www.elife.com/forum-40-3.html
firmwire part 1 : http://d-h.st/shk
firmwire part 2 : http://d-h.st/VEY
firmwire part 3 : http://d-h.st/4tJ
firmwire part 4 : http://d-h.st/ztI
FLAHTOOL (SP FLASH TOOL) : http://d-h.st/GeI
INSTRUCTIONS -
1. EXTRACT THE FIRMWARE ONTO YOUR DESKTOP
2. EXTRACT THE ZIP OF THE SP FLASH TOOL
3. OPEN THE "FLASH_TOOL.EXE" AS AN ADMINISTRATOR
4. CLICK ON SCATTER LOADING
5.BROWSE FOR "MT6589_ANDROID_SCATTER_EMMC.TXT" IN YOUR DOWNLOADED FIRMWARE FOLDER
6.OPEN IT
7. MAKE SURE ALL THE ENTRIES BELOW ARE TICK MARKED
8.THEN CLCK ON FIRMWARE>>UPGRADE (MOBLIE SHOULD NOT BE CONNECTED)
9. REMOVE THE BATTERY FOR FEW SECONDS
10.RE-INSERT IN AND WITHOUT SWITICHING ON THE MOBILE CONNECT IT
11. WAIT FOR THE PROCESS TO COMPLETE
AFTER COMPLETED U WILL SEE A GREEN RING
DISCONNECT THE MOBILE NOW AND BOOT IT UP
NOW U SHOULD FOLLOW THE PROCESS FOR ROOTING AND INSTALLING CWM FOR CHINESE FIRMWARE AND ALSO MAKE A NADROID BAKCUP ..!!!!
FOLLOW IT..!!
NOW ALL OF US HAVE THE CHINESE FIRMWARE .. LETS FLASH SOME CUSTOM ROMS
Download any of these :-
1. iNfinity HD V2: http://d-h.st/7UG
2. XPERIA HD - http://d-h.st/Tsf
3. GAMERZ ROM - https://docs.google.com/file/d/0B_biVoQFUltgQjZwN1NNc3RPZ1k/edit?usp=sharing
BEFORE PROCEEDING MAKE SURE U HAVE A NADROID BACKUP....!!
FOLLOW THIS PROCEDURE FOR FLASHING..!!
1) Download Rom.zip File
2) Put into ROOT OF Internal SD Card
3) Go To CMW Recovery BY PRESSING VOL+ AND POWER BUTTON TOGETHER OR BY MOBILE UNCLE TOOLS
4) Wipe Data/Factory Reset And Wipe Partition
5) From Advance Menu Do Dalvik Catch Clear
6) Go in Mount And Storage select FORMAT SYSTEM
7) Select Intall From SD and Select File And Click YES
8) Select YOUR ROM ZIP FILE And Select YES
9) Reboot Your System
10) Enjoy
IF U ARE STUCK IN A BOOT LOOP -
RESTORE THE NADROID BACKUP ..!!
THANKS...!!
CREDITS -
lalibm
trip007in
4peace1
sankhauaa
bhargav1991
lopestom
burakgon
AND ME (thegadgetnerd)
IT WORKS IF YOU FOLLOW THE CORRECT PROCEDURE..!!
READ THE WHOLE CAREFULLY...!!
DO IT AT YOUR OWN RISK I AM NOT RESPONSIBLE FOR ANY SORT OF DAMAGE
THANKS AGAIN...!!
on point bro but gamerz not work on e3 for now or did i missed something
Gamerz rom worked !!!
4peace1 said:
on point bro but gamerz not work on e3 for now or did i missed something
Click to expand...
Click to collapse
There are 2 versions of gamerz rom , to let it work , we have to install the General mobile discovery version . Currently i have gamerz rom installed on my e3 , i have provided the link of gamerz rom of general mobile discovery only
Thanks
thegadgetnerd said:
There are 2 versions of gamerz rom , to let it work , we have to install the General mobile discovery version . Currently i have gamerz rom installed on my e3 , i have provided the link of gamerz rom of general mobile discovery only
Thanks
Click to expand...
Click to collapse
ok let me try it this
i tried wrong one be that -v1.0 for Xolo Q800/Fly IQ446/Gionee gn708w/Symphony w125
U have to try the GENERAL MOBILE DISCOVERY VERSION
4peace1 said:
ok let me try it this
i tried wrong one be that -v1.0 for Xolo Q800/Fly IQ446/Gionee gn708w/Symphony w125
Click to expand...
Click to collapse
TRY THE GENERAL MOBILE DISCOVERY VERSION AND DOWNLOAD THE ROM AS IT IS .. DO NOT CHANGE ANY OF THE FILE'S LIKE BOOT.IMG.. !!
The General Mobile discovery one works and i have it installed on my Gionee Elife E3
Thanks
nice one but no selection of 3g on sim 2,no wifi setting
Follow
Galaxy Nexus cihazımdan Tapatalk 2 ile gönderildi
sir here you have given chinese firmware may i know which version of chinese firmware is this??? 1.2, 1.8 or 1.10(latest)
thank you
ok got it this is fw 1.2 we have to update after this
can anyone suggest which google apps package i should use to install google services in official chinese firmware posted here???
official google apps from goo.im doesnt seems to work properly it gives 492 error in play store
Just update it and install Google play store only
wont it need xml files and extra login service apk to installed in system???
milav said:
wont it need xml files and extra login service apk to installed in system???
Click to expand...
Click to collapse
Nope
from update sv1.8 all files to make Gapps works are there
just need to install apk of playstore,gmail etc
Sv1.0 old didnt have any Gapps installation files.
nandroid backup of chinese roms
can anyone upload chinese nandroid backup of their mobile so that it will be easy to flash custom roms
sheraz1015 said:
can anyone upload chinese nandroid backup of their mobile so that it will be easy to flash custom roms
Click to expand...
Click to collapse
Even I am also looking for Same...
help
can anyone help me and my friend Gavrav
sheraz1015 said:
can anyone help me and my friend Gavrav
Click to expand...
Click to collapse
@sheraz1015 milav is going to upload check this
thanx gavrav
Gauraav said:
@sheraz1015 milav is going to upload check this
Click to expand...
Click to collapse
thanx gavav
hi guys
can i install walkman music players app. without flasing custom roms..
i already rooted my phone and successfully install super user app. from step mentioned in 1st post...
i also download the xperia HD custom rom and try to install music player app but it fails??
any one plz help
ershibbu said:
hi guys
can i install walkman music players app. without flasing custom roms..
i already rooted my phone and successfully install super user app. from step mentioned in 1st post...
i also download the xperia HD custom rom and try to install music player app but it fails??
any one plz help
Click to expand...
Click to collapse
Did you flashed xperia HD ? For only music player I think you don't need root . I have also E3 , rooted stock and I am using almost all ported system apps including latest KitKat launcher , mail, camera ...without any problem. I always prefer manual system push rather that flash through cwm .I still in stock cwm.
***Root with SPFT Flash Tool Method***
for iBerry Auxus Note 5.5 / Mlais Note Pro 5.5 / Elephone P2000
[EASY ROOT METHOD]
Guys. Now we have our own first Root Method for AUXUS NOTE 5.5 STOCK ROM.
Finally this root perfect root method was possible due to SPFT version of Stock Rom
Installation Instructions
Warning: Do at your own risk. Electricity Supply failure or disconnection due to poor cable can still brick your phone beyond repair. This also breaches warranty of your phone. I am not responsible for any damages.
1) Download flashable zip file named UPDATE-SuperSU-v2.02.zip and save in root of your SDCard
2) Download and install Phone Driver / Universal Android USB Drivers (if any).
3) Download and Install ADB Driver Installer for Windows (important) while installing connect phone to pc and let is recognize .
After installation is done disconnect phone from pc.
Reboot Recommended at this point. DO NOT CONNECT YOUR PHONE RIGHT NOW.
3) Download and extract following TWRP Recovery Flash Package as per your model on desktop or anywhere on your pc.
------- Download for iBerry Auxus Note 5.5 (Download New Recovery image file by me from this thread)
------- Download for Mlais Note Pro
------- Download for Elephone P2000
4) Run as Administrator the Flash_Tool.exe from SPTools folder inside that folder you extracted.
5) Keep only TWO options checked (selected) as shown in following image (Preloader and Recovery). If options are not seen then click on "Scatter-loading" button at top-right side and select "MT6592_Android_scatter.txt" file from extracted folder. Now be sure only two options (PRELOADER and RECOVERY) selected as mentioned in following image. Unselect all other options.
Now PRESS "Download" button at top.
6) Remove battery and memory card from phone and connect PHONE to pc with usb cable. Now pc should recognize phone and flashing should start in a minute. Look at process bar in image below. WAIT WITH PATIENCE.
After flashing is done, the GREEN tick mark will be shown as shown in image below.
7) Now close program on pc and remove cable, Insert Battery and start phone in RECOVERY mode.
To start phone in recovery mode press "VOLUME UP" button and "POWER" until phone starts in TWRP Recovery mode.
8) Important: Now install/flash "UPDATE-SuperSU-v2.02.zip" in Recovery mode and Reboot phone in system (normal) mode
Done. Enjoy Press thanks if you liked my work.
IMPORTANT: The package also contains original Stock Recovery named recovery_org_stock.img. If you want to flash back to original company stock recovery, then select this file in flashing tool (Click recovery line and select this file) and then flash.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Thanks
Yeah rooted my auxus note with your guidance. Good to see that you have also shifted to iberry auxus from canvas hd. So, double excitement for me one is new phone and other is to see cmahendra with this phone. So many exciting custom rom waits for note 5.5. Thank you Sir.
baskye said:
Yeah rooted my auxus note with your guidance. Good to see that you have also shifted to iberry auxus from canvas hd. So, double excitement for me one is new phone and other is to see cmahendra with this phone. So many exciting custom rom waits for note 5.5. Thank you Sir.
Click to expand...
Click to collapse
I am glad to see first person who rooted with the help of my tutorial and files. That also confirms the steps are perfect. Actually worked for me so should work for all. Thanks a lot for your faith and trust in me. Will be around for more developement and roms.
Success!
]I have rooted by iberry-auxus note 5.5 as per your guidance.
But the USB DRIVER not correctly installed.
I have updated the driver through device manager
My operating system is windows 7 ultimate x64
Everything went smooth as you instructed
Thank you for developing this guide to root the model.
:victory:
The USB DRIVERS can be downloaded from
http://forum.xda-developers.com/showthread.php?t=2180436
Using the note for about 2weeks. Rooted successfully. Titanium backup is not working properly. Any solution for it.
Also the network refresh is poor. So network switching is very slow and many times have to manually do refresh or reboot.
latest twrp recovery
while browsing through elephone p2000 thread I came across this link which gives the latest twrp recovery
http://n2k1.com/n2k1/ELEPHONE_P2000/
Downloaded the 8.77 MB file flashed the recovery file alone through sp flash tools
Working fine on our auxus 5.5 note.
flashing the preloader is not necessary though is it?
Yes it is not necessary
hi mahendra .this is great .didn't expect rom development on fast track so soon .
going to root my brothers mobile with this method now but want to make sure if phone will receive updates normally after that.
thanks.:good:
mojahun said:
]I have rooted by iberry-auxus note 5.5 as per your guidance.
But the USB DRIVER not correctly installed.
I have updated the driver through device manager
My operating system is windows 7 ultimate x64
Everything went smooth as you instructed
Thank you for developing this guide to root the model.
:victory:
The USB DRIVERS can be downloaded from
http://forum.xda-developers.com/showthread.php?t=2180436
Click to expand...
Click to collapse
I am not sure if above USB driver is useful or not. But when you connect MT6592 Phone to PC without Battery, the PC shows a box with
"Searching drivers for YunOS system"
and if Internet is connected , it will download a tiny driver automatically from Microsoft site for Chinese Mobile Phones and an entry in Device Manager appears like
"YunOS ACB Interface"
Now Flashing Tool will automatically connect your phone to pc on next available COM PORT (COM3 or COM4 etc.)
So it is not USB Driver. It needs YunOS ACB Driver. You can find it separately somewhere on net, if searched.
baskye said:
while browsing through elephone p2000 thread I came across this link which gives the latest twrp recovery
http://n2k1.com/n2k1/ELEPHONE_P2000/
Downloaded the 8.77 MB file flashed the recovery file alone through sp flash tools
Working fine on our auxus 5.5 note.
Click to expand...
Click to collapse
Download my version of TWRP 2.7.1.0, which is tested and works perfect, includes Mount USB Storage and you can transfer files in Recovery mode.
Ito_ said:
flashing the preloader is not necessary though is it?
Click to expand...
Click to collapse
No, Preloader is not necessary but in case it is wiped or corrupted, its good to flash the original provided by company makers. I have included all Preloaders directly from respective company stock roms
sandeep101 said:
hi mahendra .this is great .didn't expect rom development on fast track so soon .
going to root my brothers mobile with this method now but want to make sure if phone will receive updates normally after that.
thanks.:good:
Click to expand...
Click to collapse
YEAH! I am always around in XDA, for the phone in my hand Thanks for appreciation
SCATTER file and Recovery for two more clone models.
Hi A L L!!!
Posted SCATTER file and Recovery for two more clone models.
3) Download and extract following TWRP Recovery Flash Package as per your model on desktop or anywhere on your pc.
------- Download for iBerry Auxus Note 5.5
------- Download for Mlais Note Pro
------- Download for Elephone P2000
Choose wisely.
Nothing happening
cmahendra said:
***Root with SPFT Flash Tool Method***
for iBerry Auxus Note 5.5 / Mlais Note Pro 5.5 / Elephone P2000
[EASY ROOT METHOD]
Guys. Now we have our own first Root Method for AUXUS NOTE 5.5 STOCK ROM.
Finally this root perfect root method was possible due to SPFT version of Stock Rom
Installation Instructions
Warning: Do at your own risk. Electricity Supply failure or disconnection due to poor cable can still brick your phone beyond repair. This also breaches warranty of your phone. I am not responsible for any damages.
1) Download flashable zip file named UPDATE-SuperSU-v2.02.zip and save in root of your SDCard
2) Download and install Phone Driver / Universal Android USB Drivers (if any).
3) Download and Install ADB Driver Installer for Windows (important) while installing connect phone to pc and let is recognize .
After installation is done disconnect phone from pc.
Reboot Recommended at this point. DO NOT CONNECT YOUR PHONE RIGHT NOW.
3) Download and extract following TWRP Recovery Flash Package as per your model on desktop or anywhere on your pc.
------- Download for iBerry Auxus Note 5.5
------- Download for Mlais Note Pro
------- Download for Elephone P2000
4) Run as Administrator the Flash_Tool.exe from SPTools folder inside that folder you extracted.
5) Keep only TWO options checked (selected) as shown in following image (Preloader and Recovery). If options are not seen then click on "Scatter-loading" button at top-right side and select "MT6592_Android_scatter.txt" file from extracted folder. Now be sure only two options (PRELOADER and RECOVERY) selected as mentioned in following image. Unselect all other options.
Now PRESS "Download" button at top.
6) Remove battery and memory card from phone and connect PHONE to pc with usb cable. Now pc should recognize phone and flashing should start in a minute. Look at process bar in image below. WAIT WITH PATIENCE.
After flashing is done, the GREEN tick mark will be shown as shown in image below.
7) Now close program on pc and remove cable, Insert Battery and start phone in RECOVERY mode.
To start phone in recovery mode press "VOLUME UP" button and "POWER" until phone starts in TWRP Recovery mode.
8) Important: Now install/flash "UPDATE-SuperSU-v2.02.zip" in Recovery mode and Reboot phone in system (normal) mode
Done. Enjoy Press thanks if you liked my work.
IMPORTANT: The package also contains original Stock Recovery named recovery_org_stock.img. If you want to flash back to original company stock recovery, then select this file in flashing tool (Click recovery line and select this file) and then flash.
Click to expand...
Click to collapse
I followed all your steps but it's not working. When I press download button it's not flashing. I waited for over an hour.
Techminator said:
I followed all your steps but it's not working. When I press download button it's not flashing. I waited for over an hour.
Click to expand...
Click to collapse
Seems drivers are not properly installed. These are new drivers by iBerry.
1) Uninstall any android driver you installed before from ControlPanel/Programs. Reboot/Restart PC/Laptop
2) Install this USB Preloader Driver http://d-h.st/kcH (from iBerry)
3) Then Install this SPFlashtool Driver http://d-h.st/vRd (from iBerry)
4) Reboot PC/Laptop/Computer , Keep pc connected to Internet on all the time. DO NOT yet connect phone to pc.
5) After computer restarts Run SPFT "flash_tool.exe" and press DOWNLOAD button
6) Now connect phone (without battery) to pc. Let windows install drivers, then flashing will start in less than 5 min. Dont wait for hours.
Hope this helps and inform if works.
PS: For GOD's sake do not quote whole opening post in your queries. Do you want me to read my own thread? Hope you have read XDA basic terms and conditions.
Rooted!
cmahendra said:
Seems drivers are not properly installed. These are new drivers by iBerry.
Click to expand...
Click to collapse
Thank You, I managed to root my phone with your help Mahendra. Also, my apologies for quoting the whole post. I suppose it needs editing including driver links. I also removed SIM card from the phone before rooting.
Rooting apart, I wanted to ask if there are any advantages/differences by installing your ROM? Can I not create a ROM by taking a complete image of my current phone's state? I was thinking about Xposed Framework. Not sure but your advice would really help.
Finally, I was wondering if there are any good flip cases available online. The local stores do not have any for this brand and model as it's fairly new in the market. The one from iBerry is Rs 990 which I think is unreasonable. Any suggestions would be much appreciated.
Also, is there a way to light up the soft buttons?
Thank You and keep up the good work.
Is there any chance of there being a cm11 port on this phone?
I don't like the icon size on the stock ROM and Titanium Backup doesn't work
Techminator said:
Thank You, I managed to root my phone with your help Mahendra. Also, my apologies for quoting the whole post. I suppose it needs editing including driver links. I also removed SIM card from the phone before rooting.
Rooting apart, I wanted to ask if there are any advantages/differences by installing your ROM? Can I not create a ROM by taking a complete image of my current phone's state? I was thinking about Xposed Framework. Not sure but your advice would really help.
Finally, I was wondering if there are any good flip cases available online. The local stores do not have any for this brand and model as it's fairly new in the market. The one from iBerry is Rs 990 which I think is unreasonable. Any suggestions would be much appreciated.
Also, is there a way to light up the soft buttons?
Thank You and keep up the good work.
Click to expand...
Click to collapse
I dont use or recommend Xposed FW. You can use as per your requirement. Works fine.
This is rooting tutorial. I will be happy if you stick to the rooting related questions in this thread from next time. A little XDA terms and conditions page will help a bit to you and us.
Yes, flip cover by iBerry is costly and even I am also looking for low-cost option.
falcon.prj said:
Is there any chance of there being a cm11 port on this phone?
I don't like the icon size on the stock ROM and Titanium Backup doesn't work
Click to expand...
Click to collapse
For icons size to change use any other launcher, like google now or nova or any other you want.
Move Titanium App to internal memory or install Link2SD, check settings and then install Titanium Backup. plz google for more info on titanium.
This is rooting tutorial. I will be happy if you stick to the rooting related questions in this thread from next time. A little XDA terms and conditions page will help a bit to you and us.
For titanium backup issues try super user app by Koushik Dutta (flashable zip file link is available in play store). First uninstall super su from the application itself. Then install super user through recovery. Ignore the warning regarding su binary.
---------- Post added at 04:27 PM ---------- Previous post was at 04:26 PM ----------
It worked for me. Just take a nandroid backup of your current rom before giving a try.
baskye said:
For titanium backup issues try super user app by Koushik Dutta (flashable zip file link is available in play store). First uninstall super su from the application itself. Then install super user through recovery. Ignore the warning regarding su binary.
---------- Post added at 04:27 PM ---------- Previous post was at 04:26 PM ----------
It worked for me. Just take a nandroid backup of your current rom before giving a try.
Click to expand...
Click to collapse
Thanks a lot for this good tip/method. +1 plz post link to exact file/version.
Here is the download link
http://download.clockworkmod.com/superuser/superuser.zip
Does not work
This method does not work after I download and flash with the latest firmware (13 Oct 2014) from iBerry site.
Hi,
First of all, I'm surprised that Lenovo Phab Plus has no forum section although Pahb 2 plus has.
Today I installed Xposed Alpha 3 and selected XPosed framework SDK for ARM 64 bit. It endded up to bootloop and worse I accidentally wiped my device without any backup (can't be worse than this).
I surfed the internet for almost a day and found few ROW ROMS on lenovo-forums which is russian website. Problem is it requires PC connection and my phone can not be read but in recovery mode. i.e. when I use:
Code:
adb devices
I got
Code:
1f82f24b recovery
I only get my phone recognized in recovery mode only since OS is wiped thanks to the naive I represent.
My question is:
1. Can anyone reach a zip ROM so I can install it directly from TWRP. I can transfer files to my phone when I'm in recovery mode as it is recognized as ADB Interface
2. Does ROW ROM require my phone to be in another mode other than recovery as I failed to get Download_with_partition.cmd to work although as I mentioned adb devices command returned my device ID and recovery word.
Your help is appreciated
Solution
After posting the thread, I found that stock rom:
Lenovo Phab Plus Stock ROM 5.1.1
It is the best ROM that it actually worked. When you extract it, you will find download.cmd. To make it work, I had to enter command line by line. Eventually it worked.
Few tips:
1. Make sure your command window is "administrator"
2. Go to "E:\Lenovo Phab Plus\PB1-770M_5,1_S405_160420_ROW\PB1-770M_5,1_S405_160420_ROW\SW" (my location) and click ctrl+shift+right mouse click and choose "Open command window here" as shown here:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Then open Command.bat located in same file using right click--> edit and execute commands on command window line by line:
Hope it helps others to make their life much easier than this horrible day
New clean install guide needed
Hai..
My phab plus spec
Model : PB1-770M
Soft ver : PB1-770M_150814
Android ver : 5.0.2
My problem is :
- infected by virus/malware (popup ads)
Need to fresh install stock rom.
I already download the stock rom you give.
How to install new clean rom, and how to make new clean partition.
Pls teach step by step.. till finish..
Note : my phab plus still can running as normal, only problem with malware/virus (popup ads). Already factory reset, but still same.. i think it need to newly installed stock rom.
Help needed, and really appreciate.. thanks
Hazeriff said:
Hai..
My phab plus spec
Model : PB1-770M
Soft ver : PB1-770M_150814
Android ver : 5.0.2
My problem is :
- infected by virus/malware (popup ads)
Need to fresh install stock rom.
I already download the stock rom you give.
How to install new clean rom, and how to make new clean partition.
Pls teach step by step.. till finish..
Note : my phab plus still can running as normal, only problem with malware/virus (popup ads). Already factory reset, but still same.. i think it need to newly installed stock rom.
Help needed, and really appreciate.. thanks
Click to expand...
Click to collapse
Is your phone rooted ? No popup could be that severe unless it is rooted. Also you may first update it to 5.1.1 from phone update in settings. If it gave you "network fails", it is OK. Lenovo service is down in some countries, so install cloud VPN from google play store, run it, then go again to update phone and it will work.
If factory reset doesn't work, it means your SD card or internal storage has some infected files. Use Kaspersky mobile security to scan your device.
wbadry said:
Is your phone rooted ? No popup could be that severe unless it is rooted. Also you may first update it to 5.1.1 from phone update in settings. If it gave you "network fails", it is OK. Lenovo service is down in some countries, so install cloud VPN from google play store, run it, then go again to update phone and it will work.
If factory reset doesn't work, it means your SD card or internal storage has some infected files. Use Kaspersky mobile security to scan your device.
Click to expand...
Click to collapse
Yes, mine is rooted..
I already take out sdcard.. & factory reset.. result still same..
I even try install av, so many av i try.. even kaspersky..
Yet, result still same.. av cannot catch/detect it.. it just says normal..
Many things has been done, clear cache, web browsing history.. whatever i already try..:crying:
I belive i need to fresh install stock rom with new partition..
Only thing is, i dont know how to do it on lenovo..
I only know on samsung using odin...
Really, really need help here...
Hazeriff said:
Yes, mine is rooted..
I already take out sdcard.. & factory reset.. result still same..
I even try install av, so many av i try.. even kaspersky..
Yet, result still same.. av cannot catch/detect it.. it just says normal..
Many things has been done, clear cache, web browsing history.. whatever i already try..:crying:
I belive i need to fresh install stock rom with new partition..
Only thing is, i dont know how to do it on lenovo..
I only know on samsung using odin...
Really, really need help here...
Click to expand...
Click to collapse
Hmmm...
Anybody care for help?
Xda experts..??
Hazeriff.. this pop-up comes up when you are browsing, you can just ignore it.. Its just a false pop-up
Normally you dont get pop-up like these on Android
Hazeriff said:
Hmmm...
Anybody care for help?
Xda experts..??
Click to expand...
Click to collapse
Thanks dude!! You saved my butt. This is exactly what I needed and worked perfectly.
You are a legend!
wbadry said:
After posting the thread, I found that stock rom:
It is the best ROM that it actually worked. When you extract it, you will find download.cmd. To make it work, I had to enter command line by line. Eventually it worked.
Few tips:
1. Make sure your command window is "administrator"
2. Go to "E:\Lenovo Phab Plus\PB1-770M_5,1_S405_160420_ROW\PB1-770M_5,1_S405_160420_ROW\SW" (my location) and click ctrl+shift+right mouse click and choose "Open command window here" as shown here:
Then open Command.bat located in same file using right click--> edit and execute commands on command window line by line:
Hope it helps others to make their life much easier than this horrible day
Click to expand...
Click to collapse
wbadry said:
After posting the thread, I found that stock rom:
Lenovo Phab Plus Stock ROM 5.1.1
It is the best ROM that it actually worked. When you extract it, you will find download.cmd. To make it work, I had to enter command line by line. Eventually it worked.
Few tips:
1. Make sure your command window is "administrator"
2. Go to "E:\Lenovo Phab Plus\PB1-770M_5,1_S405_160420_ROW\PB1-770M_5,1_S405_160420_ROW\SW" (my location) and click ctrl+shift+right mouse click and choose "Open command window here" as shown here:
Then open Command.bat located in same file using right click--> edit and execute commands on command window line by line:
Hope it helps others to make their life much easier than this horrible day
Click to expand...
Click to collapse
Hello to all.
unfortunately lacking all the commands of the txt file.
You can post all commands?
thank you
---------- Post added at 12:56 PM ---------- Previous post was at 12:44 PM ----------
wbadry said:
After posting the thread, I found that stock rom:
Lenovo Phab Plus Stock ROM 5.1.1
It is the best ROM that it actually worked. When you extract it, you will find download.cmd. To make it work, I had to enter command line by line. Eventually it worked.
Few tips:
1. Make sure your command window is "administrator"
2. Go to "E:\Lenovo Phab Plus\PB1-770M_5,1_S405_160420_ROW\PB1-770M_5,1_S405_160420_ROW\SW" (my location) and click ctrl+shift+right mouse click and choose "Open command window here" as shown here:
Then open Command.bat located in same file using right click--> edit and execute commands on command window line by line:
Hope it helps others to make their life much easier than this horrible day
Click to expand...
Click to collapse
please help me because i have brick my LENOVO PHAB PLUS
thanx it's work with me
frimware flashed
i need your help. its urgent. i am having lenovo phab plus but it is not working,
problem is os wiped, wrong flashing, even logo is not coming, if you have any solution for this please let me know on my email address
[email protected].
humble request. please
Thanks brother,I think i try 50+ sites and finally your one is working for me
bro can you help me to fix my phab plus
udhay441 said:
Thanks brother,I think i try 50+ sites and finally your one is working for me
Click to expand...
Click to collapse
bro can you help me to fix my phab plus i brick my phab plus, and everytime i do the fastboot it always say that tz.bmn is error can u help me
you guys, rock
Hi, thanks for the ROM file, unfortunately, even if everything goes well, my PB1-770M will stay in the bootlop
I do not even get into recovery, I do not even see the indication when the charger is connected. Perhaps the motherboard is damaged, right?
Flash official Rom for Lenovo push plus -770M
Firmware File
Search
Home☰
Lenovo Phab Plus PB1-770M
Home > Lenovo > Lenovo Phab Plus PB1-770M
On this page, you will find the official link to download Lenovo Phab Plus PB1-770M Stock Firmware ROM (flash file) on your Computer. Firmware comes in a zip package, which contains Flash File, Flash Tool, USB Driver and How-to Flash Manual.
Download Lenovo Phab Plus PB1-770M Stock Firmware (flash file)
File Name: Lenovo_Phab_Plus_PB1-770M_USR_S000169_151229.zip
File Size: 2 GB
How to Flash: Follow Tutorial
Firmware Link: Click here to Start Download
Download Firmware
Download Flash Tool
Download USB Driver
For PC Software
How to Flash
Step 1: Download and extract the Lenovo Phab Plus PB1-770M stock firmware package on your computer.
Step 2: After extracting the package, you will be able to get the Firmware File, Flash Tool, Driver and How-to Flash Guide.
Step 3: Install the provided USB Driver on your Computer, and if in case USB Driver is already installed, SKIP this step).
Step 4: Follow the How-to Flash Manual to Flash the Firmware on your Lenovo Phab Plus PB1-770M Device.
Follow Detailed Guidelines
Readme Once:
[*] Take a Backup: If you are going to flash the above Firmware on your Lenovo Phab Plus PB1-770M device, then take a backup of everything as because your personal data will be deleted after flashing the stock firmware.
[*] The firmware shared on this page is officially released by the company and helps you to recovery your device if you ever got bootloop, software error, update error, hanging and dead issue.
COMMENTS
Site Links
Donate
Privacy Policy
Contact
Trending
Alcatel Firmware
Samsung Firmware
Vivo Firmware
Connect
RSS
Facebook
Made with ♥ in Spain | Powered by BlueHost
Copyright © 2014-2018 Firmware File. All Rights Reserved.
low internal memory after flafsh lenovo pb1-770m
dear friends
i used the stock rom that you share it.
i flashed my lenovo pb1-770m with it.
but i found my internal memory changed to 1.6G
I ONLY HAVE 250MB FREE MEMORY.
please help me.
what i must be do for this problem?
thaks
mazvir said:
dear friends
i used the stock rom that you share it.
i flashed my lenovo pb1-770m with it.
but i found my internal memory changed to 1.6G
I ONLY HAVE 250MB FREE MEMORY.
please help me.
what i must be do for this problem?
thaks
Click to expand...
Click to collapse
I had the same problem and I solved it by installing TWRP and resizing /data partition via it.
Downloaded the above FW successfully but when I followed the step-by-step guide, I got this error message:
==================
PS C:\Users\HP_AIO\Downloads\Lenovo\Phab Plus\PB1-770M_5,1_S405_160420_ROW\PB1-770M_5,1_S405_1
60420_ROW\SW> adb reboot bootloader
adb : The term 'adb' is not recognized as the name of a cmdlet, function, script file, or
operable program. Check the spelling of the name, or if a path was included, verify that the
path is correct and try again.
At line:1 char:1
+ adb reboot bootloader
+ ~~~
+ CategoryInfo : ObjectNotFound: (adb:String) [], CommandNotFoundException
+ FullyQualifiedErrorId : CommandNotFoundException
Suggestion [3,General]: The command adb was not found, but does exist in the current location. Windows PowerShell does not load commands from the current location by default. If you trust this command, instead type: ".\adb". See "get-help about_Command_Precedence" for more details.
PS C:\Users\HP_AIO\Downloads\Lenovo\Phab Plus\PB1-770M_5,1_S405_160420_ROW\PB1-770M_5,1_S405_160420_ROW\SW>
=============================
I am on Windows 10 and it's Windows Power Shell that popped up.
Any help, please?
Thank you.
This is good I have Lenovo PB1-770N and work for me just I connect my phone and open the zip then I go to SW folder and press "Download.cmd " and ebriting go by self,lol them flash by self we don't need do anything lol. Thanks for the good rom.
NOTE: don't turn off your phone just connect and press " Download.cmd" file