[Q] S3 stuck at FIrmware upgrade encountered an issue - Verizon Samsung Galaxy S III

So I have had my S3 rooted for a long while. But the past few weeks it's been running a bit slower. This week it started randomly turning off. I thought it was my battery at first. But then when I tried to turn it back on it got stuck at the Galaxy s3 screen and would not get into the OS.
I tried to get into recovery, it froze on the splash screen. I made sure both were actually frozen by leaving it sitting there for 30 min to an hour.
Tried to flash using this thread: http://forum.xda-developers.com/showthread.php?t=1974114
It kept just sitting at writing NAND.
Now my phone says "Firmare Upgrade encountered an issue, please select recovery mode in kies and try again"
Kies will not connect my device. It sees it but will not complete the connection. I tried using the model and IMEI number to upgrade firmware but it still would not connect to do that.
More searching lead me to this: http://forum.xda-developers.com/showthread.php?t=2581166&page=11
But I can't get into OS or recovery so I don't think this would work.
Any suggestions on what I can do from here? I only really need the phone to work for a few more months. My old Droid incredible just doesn't cut it at this point.

Sorry to bump, but nobody has anything for this? I haven't really found any other options.

Your bootloader is fine so that thread won't help you. What was the last version of touch wiz that was on your phone before you ran into problems?

Related

[Q] Galaxy S2 Soft Bricked after root....

Hi everyone!! New here, but not new to Forums in general. I searched around and couldn't find my exact issue, so I figured I’d start a new thread. This is gonna be kinda long, but I wanna give as many details as I can to keep things accurate.
My wife and I both have the Galaxy S2 T989 (T-Mobile). Both purchased like new off eBay. When I got hers a couple months ago, as soon as I got it I factory reset and wiped the caches, upgraded to JB via Kies, and then turned right around and rooted it via Odin using the instructions found on galaxys2root.com. Everything went flawless, took me less than a half an hour total for everything. I got mine a couple months later and did the exact same process as soon as I got it in the mail. However after rooting on Odin and getting the green pass just like hers, it got stuck in a boot loop when it rebooted. It would go as far as the "galaxy S2" splash screen, and sometimes past that to where the Android takes off, then reboot, or freeze. It then became unresponsive to any button pushes and I had to pull the battery to get it to shut off (The battery is a new OEM Samsung battery incidentally). I ultimately had to unroot, re-install ICS and re-upgrade back to JB via Kies again to get out of the loop. I did this whole process 3 times to make sure it wasn’t something I did. So I’m still running unrooted with JB on it now.
The only thing I noted that was kinda odd was that when I open Rom Manager in my current non rooted state, it shows that I already have CWM and TWRP installed on it. Even though when I go to recovery mode it's the standard OEM Samsung menu. I never installed TWRP, and CWM was only on it for a bit when I was in the boot loop. Could this be my issue? Are they both still somewhere on my phone interfering with each other and I can only see them via ROM manager?
Sorry for such a long first post, and thanks in advance!
addamT989 said:
Hi everyone!! New here, but not new to Forums in general. I searched around and couldn't find my exact issue, so I figured I’d start a new thread. This is gonna be kinda long, but I wanna give as many details as I can to keep things accurate.
My wife and I both have the Galaxy S2 T989 (T-Mobile). Both purchased like new off eBay. When I got hers a couple months ago, as soon as I got it I factory reset and wiped the caches, upgraded to JB via Kies, and then turned right around and rooted it via Odin using the instructions found on galaxys2root.com. Everything went flawless, took me less than a half an hour total for everything. I got mine a couple months later and did the exact same process as soon as I got it in the mail. However after rooting on Odin and getting the green pass just like hers, it got stuck in a boot loop when it rebooted. It would go as far as the "galaxy S2" splash screen, and sometimes past that to where the Android takes off, then reboot, or freeze. It then became unresponsive to any button pushes and I had to pull the battery to get it to shut off (The battery is a new OEM Samsung battery incidentally). I ultimately had to unroot, re-install ICS and re-upgrade back to JB via Kies again to get out of the loop. I did this whole process 3 times to make sure it wasn’t something I did. So I’m still running unrooted with JB on it now.
The only thing I noted that was kinda odd was that when I open Rom Manager in my current non rooted state, it shows that I already have CWM and TWRP installed on it. Even though when I go to recovery mode it's the standard OEM Samsung menu. I never installed TWRP, and CWM was only on it for a bit when I was in the boot loop. Could this be my issue? Are they both still somewhere on my phone interfering with each other and I can only see them via ROM manager?
Sorry for such a long first post, and thanks in advance!
Click to expand...
Click to collapse
Try flash a stock firmware by using flashtool, it will work 100%:angel:
revernwe therefore
addamT989 said:
Hi everyone!! New here, but not new to Forums in general. I searched around and couldn't find my exact issue, so I figured I’d start a new thread. This is gonna be kinda long, but I wanna give as many details as I can to keep things accurate.
My wife and I both have the Galaxy S2 T989 (T-Mobile). Both purchased like new off eBay. When I got hers a couple months ago, as soon as I got it I factory reset and wiped the caches, upgraded to JB via Kies, and then turned right around and rooted it via Odin using the instructions found on galaxys2root.com. Everything went flawless, took me less than a half an hour total for everything. I got mine a couple months later and did the exact same process as soon as I got it in the mail. However after rooting on Odin and getting the green pass just like hers, it got stuck in a boot loop when it rebooted. It would go as far as the "galaxy S2" splash screen, and sometimes past that to where the Android takes off, then reboot, or freeze. It then became unresponsive to any button pushes and I had to pull the battery to get it to shut off (The battery is a new OEM Samsung battery incidentally). I ultimately had to unroot, re-install ICS and re-upgrade back to JB via Kies again to get out of the loop. I did this whole process 3 times to make sure it wasn’t something I did. So I’m still running unrooted with JB on it now.
The only thing I noted that was kinda odd was that when I open Rom Manager in my current non rooted state, it shows that I already have CWM and TWRP installed on it. Even though when I go to recovery mode it's the standard OEM Samsung menu. I never installed TWRP, and CWM was only on it for a bit when I was in the boot loop. Could this be my issue? Are they both still somewhere on my phone interfering with each other and I can only see them via ROM manager?
Sorry for such a long first post, and thanks in advance!
Click to expand...
Click to collapse
hi,
can 'be that your device has some residual old. Do as you have advised. install a stock rom and firmware, so it becomes a new cell phone. After odin starts TWRP (much better) and root.
I would flash a complete bone stock Rom using Odin and start over. Also rom manager was highly discouraged on the AT&T version of the s2 so I don't know what the stance is on T-Mobile's version
Sent from my CLEAN Note ll
brandonarev said:
I would flash a complete bone stock Rom using Odin and start over. Also rom manager was highly discouraged on the AT&T version of the s2 so I don't know what the stance is on T-Mobile's version
Sent from my CLEAN Note ll
Click to expand...
Click to collapse
Thanks for the advice! Should i flash it back to ICS then try to root again via Odin before i upgrade back to JB? I'm guessing there's something that isn't getting wiped. Since i can run CWM and Root with Odin without a hitch. it's the initial reboot after all that is done that I go into the boot loop.
tainiun rioters
pierm said:
hi,
can 'be that your device has some residual old. Do as you have advised. install a stock rom and firmware, so it becomes a new cell phone. After odin starts TWRP (much better) and root.
Click to expand...
Click to collapse
Sorry for my ignorrance, what exactly is TWRP, and is it now on there because i used Odin and it installed it automaticly? And do i want to use this vice CWM?
One more question...before i try all this, can i backup everything on Kies just like i would be able to with CWM and reinstall if my root fails again? I've only used Kies for firmware upgrade, never to reinstall a backed up copy of my phone.
Thanks!
addamT989 said:
Sorry for my ignorrance, what exactly is TWRP, and is it now on there because i used Odin and it installed it automaticly? And do i want to use this vice CWM?
Click to expand...
Click to collapse
addamT989 said:
One more question...before i try all this, can i backup everything on Kies just like i would be able to with CWM and reinstall if my root fails again? I've only used Kies for firmware upgrade, never to reinstall a backed up copy of my phone.
Thanks!
Click to expand...
Click to collapse
Hi
TWRP and the 'one touch recovery, better than CWM.
The backup kies can not recover from CWM
steps:
install odin, after recovery, nandroid backup, ROM, and root.
hi
Flash the stock firmware using odin!!..it will work!
Sent from my GT-N7100 using xda premium
freezes then booted
Hello I have this problem with my galaxy s2 i9100. After reboot the phone wasn't booting something like "boot loop" so I re flashed the firmware and now the phone boots up but after the boot it freezes immediately. So I decided to install clock work mod recovery and install cyanogen mode 11 with cyanogen mode the phone boots up and are able to be used again until the screen goes to sleep mode or the power button is pressed then the screen goes black and doesn't turn on after long pressing the power button it reboots. So I don't know what else to do I have tried kernels, operating systems re flashing reseting and nothing helps. No need to tel me to do resettings. Also my galaxy s2 i9100 chip has insane chip bug but I don't know if it has to do something with my problem.

Help needed as I'm thinking about giving up

Hi all,
Firstly I apologise for actually posting as I've spent a week trying to not be a twat and to fix it myself but alas I'm at the end of my tether.
OK I have a Tab 2 10.1 P5100 (thus with sim). I originally got it about 3 years ago in Poland and their OTAs are about as frequent as, well, they never happened. So, over the years whilst working there I flashed via Odin various official updates to get it up to scratch. Last one being Jelly Bean.
Everything has been fine until a week ago when suddenly it would boot, get to the log in screen, let me enter my pin, work for 10 seconds and then suddenly reboot. It's an endless loop but it's not stuck on booting up it just crashes ONCE started up fully.
It won't connect to Kies. Now, this is probably the rubbish cable (This is the third official cable in 3 years I've goe thru). The system restore option from manual booting does nothing and wipes nothing so I've been trying to just load an official ROM from the SD..that does nothing.
It starts to install and then goes back to the "no command" screen.
Can I simply download something onto the SD and install from there? the zip files I keep trying dont work.
Any advice is appreciated!

[Q] HELP!! Sprint Galaxy S5

Hello everyone! I was sincerely hoping that someone would be able to help. I believe I messed up my phone beyond repair by trying to root it for the 2nd time. I rooted my phone in Sept 2014 and accidentally dropped it and broke the LCD (not the actual screen, but a piece inside of the phone). Samsung replaced the screen but they had to reset it so I lost the root. I wanted to try to root it again today. I already had all the tools; Odin, Superuser, and Philz Recovery. I put the phone into download mode, flashed Philz, and Odin said "Passed". When I put the phone into recovery mode, it didn't look like it did before. It just looked like the android stock recovery. I assumed (noob) that I may have done something wrong. So I tried flashing it again and it failed and was stuck in the download mode (Do not turn Target off). I waited approx 30 min and just said, "Screw it" and pulled the battery. I know stupid. Then I got the "Firmware upgrade encountered an issue message..." I did some research and many people on here and other android forums were telling others with somewhat of the same problem to download the stock rom. I'm currently downloading it but am worried it's going to do the same thing; "fail". I will update as soon as I try to flash the stock rom, but if anyone has other options, I'd so appreciate them.
Thanks so much for helping.....
Hedup34
P.s. I had the most up to date software for Sprint (maybe that was the problem)

Samsung Galaxy S6 (sprint variant) failed firmware flash FAC LOCK

Let me start by addressing I know this isn't the sprint thread but there's a lot more development here which equals more help. Plus this issue seems to be able to happen to any variant.
Second, this isn't my device I'm trying to see if it can be fixed for a friend. I'm not that familiar with Samsung devices but I have been able to get them working in the past via Odin or kies but this time I need some help.
So this is what's going on, my friend recently rooted his S6(SM-920P) not sure which method he used (don't think it matters at this stage) and was on stock rom (LP5.0.2) with xposed framework installed. He hadn't changed the kernel AFAIK oh but I did install TWRP for him and everything was working. Long story short he woke up a couple days ago to his phone being unable to turn back on. I told him how to get to download mode and I asked him what did it say on the top left corner it said something like "system binary not SEandroid locked" underneath that it said fac lock
So I had him give me the phone thinking somehow it did a OTA update while he was asleep or something either way I was confident using Odin to flash the firmware would solve the issue. Had the firmware finished flashing I'm confident it would have but halfway through Odin simply froze on installing system. I figured its just gonna take a while 45 mins later it was still stuck at the same spot.
Not really thinking about it I figured I will just reboot the phone back into download mode restart the process it should be fine. Not a good idea. Now all I get is a green screen saying to access the smart switch emergency recovery system. But it gets better.
My computer isn't recognizing the device now. I installed smart switch software and it's not recognizing it. I even installed Kies and it's not recognizing either.
Is his phone toast or what? I tried emergency system recovery but I need the S/N of his phone to possibly get this thing working again, but it boot into anything anymore except the screen that says Samsung switch...
PLEASE HELP ME if it's bricked it's bricked I get that but if there's a way to figure out what to do I'm all ears. Thanks in advance

N8013 stuck at samsung logo

Hello;
several days ago, suddenly my N8013 restarted. After rebooting, it stuck at Samsung logo, and I couldn't go to Recovery mode. I flashed an official rom from sammobile. the process was passed but my N8013 problem didn't solve.
What's the solution? Is it a hardware problem??
I don't know exactly what happened, mine did the same thing. I fiddled around with it enough that i got it to reload back to samsung 'new' but it never recovered where it was at the time it went haywire. I installed Kies on my PC and let it update the kernel to the latest stock. I had not rooted or anything up to that point. it just went kapuut. Now I am rooted and tried a couple ROMS, but so far I keep coming back to stock because I can't get something or another to work right (or at least the way I am used to)

Categories

Resources