Hello all there , and happy with first post here even am interrupted with my Galaxy tab 7.7
my tab sprayed with water and it was working normally but suddenly i powered off , and when i tried to open it it hangs on " Galaxy Tab 7.7 ".
I tried to login to recovery mode but it open in few seconds of recovery mode in few seconds then restart.
i tried the download mode and it works , i downloaded firmware 4.1.2 with only one file and uploaded it successfully through Odin .
But with the same issue , open and hangs on welcome " Galaxt Tab 7.7" , also when i tired to power off it , it restart again and stop in the same message till its battery become empty .
Any suggestions please ?
I just did the same......
This is what worked for me....
Do this immediately. ..you tab can get rust inside...need
To dry it out ASAP.
Get small skinny metal sim card removal tool.
Pry the front screen out and carefully then remove everything
You can.all boards plugs battery etc.
Then put all big stuff into a box of uncooked rice.
Leave for a week.then re assemble..
Put on charge...
When charged got to download mode.
Flash JB stock rom...
Now it may boot loop..don't worry.
Go to recovery and factory reset.
Now start and your up and running again.
I had to flash rom twice on mine.....before I could get recovery to open.
Before attempting it watch the YouTube video how to
Get battery out of 7.7
This will give you an idea how things unclip
Be careful. Good luck.
Related
Call me stupid! I tried flashing Galaxy Ace S5830 firmware into my Fit and all I've got was a white screen. Though I heared the booting sound while flashing it, so i was not affraid to continue it. The odin flash got a "PASSED" message so I disconnect the phone, still with white screen, removed the battery, pressed the three buttons of hope... and all i've got still is the white screen..... connect again to odin... got the com port mapping... and flash back stock galaxy fit rom... during the reset... tara!!!!!! got back my Galaxy Fit intro!!!.... LOL!!!
Just telling my story that's all!!!
thnks for sharing d experience
i too did such stuff with my motorola v8 years back
Samsung Galaxy S5 G900A (AT&T)
Previously on a day off I became very bored, and decided to root my phone. After playing around with everything for a day i did not like it. So i just went into recovery mode and did factory rest on my phone. Now I used supersu and a basic root everything worked perfect after i rooted it. But once I tried to put the stock firmware back on my phone it started acting funny. With showing Unfortunately Context Service has stopped. It was so absurd my phone couldnt function properly. I tried flashing the stock firmware on there in hopes that it would fix my problem, but it only made my phone completely inoperable. I have been trying multiple ways to fix this using odin v3.09 and odin v 3.10.6. Here are some of the files I have tried to get my phone back to stock. (G900AUCU1ANCE_G900AATT1ANCE_G900AUCU1ANCE_HOME.tar.md5) I have tried downgrades. Odin seems to fail on every single one besides this set up (AP_G900AUCU1ANCE_964333_REV00_user_low_ship_MULTI_CERT.tar.md5) (CP_G900AUCU1ANCE_964333_REV00_user_low_ship_MULTI_CERT.tar.md5) (CSC_ATT_G900AATT1ANCE_964333_REV00_user_low_ship_MULTI_CERT.tar.md5) Odin loads those three files onto my phone perfectly with in 3 minutes but after they are installed on my phone. When i power it up it gets through the first screen and only shows half of the samsung logo freezes and goes to a black screen with a blue light. I have been working at this problem for a little over a week a couple hours a night and i really can not seem to make any progess. Help would be greatly appreciated.
Still having troubles
Flashes firmware perfectly fine but still can not seem to get past the samsung logo loading super slow and then just cutting out and going to a black screen with a blue stationary light on top left of phone.
Still looking for advice
bump
ksutinen said:
Flashes firmware perfectly fine but still can not seem to get past the samsung logo loading super slow and then just cutting out and going to a black screen with a blue stationary light on top left of phone.
Still looking for advice
bump
Click to expand...
Click to collapse
Boot into recovery mode and do full wipes wipe cache ,wipe del Vick cache,factory reset
I think this will resolve your problem
Regards
Mohamed786
Ok...so I'm using the SM-N900 . I installed pakeka rI'm v6 and decided to go for Dr. Khetan rom L23. I installed it and after a while I decidedo to go back to stock so I booted into philz recovery , did a full wipe, and went into power option and selected to reboot into download mode. After that it rebooted and my phones screen went completely blank and later these "gold dust" kinda appearance came on the screen. I waited a while still same and then I took out the battery, waited for about five minutes , inserted the battery and still that same appearance , no logo screen , no recovery , no download mode, just that blank "gold dust" screen. So this time around I just booted into download mode (blindly of course) and then I pressed volume up assuming it's already in download mode since screen is blank. Opened Odin and flashed stock firmware and it was a success. After that it took about almost 10 minutes before finally the device setup screen appeared ( whewwww!) ...Since funny since then again, phone''s back to normal...but my question is,
...how did this happen?
...Has anyone experienced that before?
...What could've caused that?
...what could have been the immediate remedy in this situation?
...could it be my device problem that I need to be aware of or its just a software problem?
Please help, I need answers..
my samsung galaxy s6 is using android marshmalow,it started last night when out of nowhere it started to reboot itself,i tried restarting the phone but after a few seconds of being on it rebooted it self into the samsung galaxy s6 powerd by android state and keeps showing the white led light and just stays there,i tried wiping particion,factory reset,entering safe mode,but it keeps going back to that exact same state,i also tried charging the phone for several hours but keeps coming back to that state
Note:i can turn the mobile off,and when i do that the phone doesnt reboot,i only reboots when i try to leave it on
Edit:
-so i now managed somehow to boot it into safe mode and it doesnt reboot,but once i exit safe mode it start the hole thing over again.Note:sometimes when i boot it to safe mode it reboots some times it doesn´t
Hello mate just do this it wil take you to the latest fiwmware for your s6 but every thing will be deleted its emergency firmware recovery on smart switch this wil work 100% dont think just do it this will fix every single thing i but try first to flash a stock rom via odin if that doesnt work than you have to do a emeegency firmware recovery i had the same problem even when i flash a rom via odin did not work but this wil fix it for sure just go to the link below and try it out good luck!
https://youtu.be/7ncsfXdjL_Q
The last time I ever see my Tablet Gt N8000 (Made in Vietnam) :crying:
Before it happend I was eating a Hamburger, I just use my camera and made a video...You know, some random videos like crappy stuff.
Then after I stop recording, It just hangs and reboot.
It just got stuck on Samsung Logo, I was not scared that time, I tried to use recovery like pressing Volume Up and Power Button,
you guys all said it was easy to use recovery, but NO, NOT FOR ME.
My tablet is so different that he wont let me use Recovery.
When I pressed the Power Button + Volume Up, It boots. I was waiting for the recovery screen but NO! Something bad happend It boots again.
Whenever I try to use recovery, it boots again like
I pressed the key to go to Recovery Mode
it says "Samsung Galaxy Note 10.1"
Then OFF then there goes again "Samsung Galaxy Note 10.1"
But it didnt go recovery mode, it goes to "Samaung Logo" now.
Its like denying my Recovery Command.
Then I have no choice but to use Odin and the Samsung N8000 Firmware.
I used Vietnam, go to odin then put the md5 then start.
THEN SOMETHING HAPPEND! It FAILED! I did it again, I unplugged and plugged the USB then FAILED! FAILED! FAILED! F*CKING FAILED!
F*CK THIS SH*TTY TABLET.
I try to find a way but no! Nothing. Only a Legend can solve this problem.
If you comment about more firmwares..No! Just No! I Tried It.
I Even USED 2 DIFFERENT FIRMWARES! ALL VIETNAM!
This is harder than you think.
R.I.P Samsung Galaxy Note 10.1 GT-N8000. :crying:
Some information may help .
What firmware what fail error in Odin .
Or see multiple identical Odin / firmware fail posts .
Mine is made in viet too. Fortunately, i dont have any issue at all. I suggest to bring your tablet to your trusted phone repairer and tell them what's your problem. Because it's hard to predict(diagnose) what's going on whit your tablet. It may caused by emmc/camera sensor error, so you need to replace one/both of them. if you lucky enough, it well be just firmware failure.