Database Info

help with s-on

Can someone please help, I'm truly stuck here.
I have followed the guide here..
http://forum.xda-developers.com/show....php?t=1460713
I have managed to remove the revolutionary logo, and all was good. I then attempted to install the following RUU...
RUU_Saga_HTC_Europe_1.28.401.1_Radio_20.28b.30.080 5U_38.03.02.11_M_release_177977_signed
Went through all the prompts but the program "hung" at the sending screen. After around an hour I pulled the usb cable, yay the phone still boots. However I was still at the old HBOOT (cant remember the numbers 6.0.0002 or something ) and with the custom rom.
Though this might be a problem with the RUU... NAY.
I have since tried he following..
RUU_Saga_HTC_Europe_1.47.401.4_Radio_20.28I.30.085 AU_3805.06.02.03_M_release_199410_signed
RUU_Saga_S_HTC_Europe_2.10.401.5_Radio_20.4801.30. 0822U_3822.10.08.04_M_release_219480_signed
RUU_Saga_O2_UK_1.31.206.1_Radio_20.28b.30.0805U_38 .03.02.14_M_release_178935_signed
All with the same results.
So I downgraded the hboot manually to 0.98.0002 and tried them all again. Still no luck.
The reason I have tried the different RUU is that it was originally from carphone warehouse. Their phones are generally unbranded so assumed it would be a standard euro ruu.
Please help.

I really don't get what the problem is. Removing the "Revolutionary" logo isn't the same as being S-ON. But check out the link below to see if it helps.
forum.xda-developers.com/showthread.php?t=1549636

@pttynan
PLease run the fastboot command "fastboot getvar all" remember to remove your imei and serial from your post.
Then I will direct you to a solution

foX2delta said:
@pttynan
PLease run the fastboot command "fastboot getvar all" remember to remove your imei and serial from your post.
Then I will direct you to a solution
Click to expand...
Click to collapse
Hi Fox2delta. The command gives the following.
INFOversion: 0.5
INFOversion-bootloader: 0.98.2000
INFOversion-baseband: 38.03.02.11
INFOversion-cpld: None
INFOversion-microp: None
INFOversion-main: 1.28.401.1
INFOserialno: HT13Jxxxxxxxx
INFOimei: 3550670xxxxxxxxx
INFOproduct: saga
INFOplatform: HBOOT-7230
INFOmodelid: PG8810000
INFOcidnum: HTC__001
INFObattery-status: good
INFObattery-voltage: 4136mV
INFOpartition-layout: Generic
INFOsecurity: off
INFObuild-mode: ENG
INFOboot-mode: FASTBOOT
INFOcommitno-bootloader: 7b851d36
INFOhbootpreupdate: 12
INFOgencheckpt: 0
all: Done!
finished. total time: 0.031s

Dont suppose anyone has any thoughts on this? Carphone flat out refused to touch it once the noticed S-OFF

[q] phone stuck in hboot with nothing else!!

hey, my phone is spoilt and im in desperate help of somebody who can help me with my HTC Sensation XE w Audio Beats.
This is what happened,
i was trying to root my phone with help from hansoon all in one toolkit, after unlocking the device and trying my best to install recovery it comes to no avail, had been receiving error when tryng to install / flash pg58img from hboot ( model id incorrect ) . later after i accidentally click on flash kernel and my phone restarted on its own and got stuck in hboot thereafter. I don't have recovery, no USB debugging mode for me to superCID and ive search the whole entire forum for a cure.. i really wish somebody would help me out here as i really want to get my only phone working and running.
UNLOCKED
pyramid pvt ship s-on rl
hboot. 1.27.0000
emmc-boot
thats all i have, i apprieciate anybody who is willing to help me thank you so much!

yuzhi92 said:
hey, my phone is spoilt and im in desperate help of somebody who can help me with my HTC Sensation XE w Audio Beats.
This is what happened,
i was trying to root my phone with help from hansoon all in one toolkit, after unlocking the device and trying my best to install recovery it comes to no avail, had been receiving error when tryng to install / flash pg58img from hboot ( model id incorrect ) . later after i accidentally click on flash kernel and my phone restarted on its own and got stuck in hboot thereafter. I don't have recovery, no USB debugging mode for me to superCID and ive search the whole entire forum for a cure.. i really wish somebody would help me out here as i really want to get my only phone working and running.
UNLOCKED
pyramid pvt ship s-on rl
hboot. 1.27.0000
emmc-boot
thats all i have, i apprieciate anybody who is willing to help me thank you so much!
Click to expand...
Click to collapse
Go to fastboot on your device
Connect it to pc (usb debugging enable is not required) (phone reads fastboot usb)
Then go to your adb folder on pc
And Type this
fastboot getvar all
Post the complete output except imei and serial number
I'll guide you through the process after this
Sent from my pyramid.. Through blazing fast sonic waves

Just download the latest RUU for your device and run it

Yeah do that lol u can get ur ruu from file factory
Sent from my HTC One S using xda premium

[SOLVED] OP's problem was solved on the irc over 5 hours ago.

Stuck in the same boot loop with my htc sensation
i just tried to flash my htc sensation xe for the first time, i successfully did S-OFF using the revolutionary tool and then tried to install ClockworkMod Recovery from PG58IMG.zip which succeeded,
but i havent been able to boot up the device since doing that. its stuck on the htc logo. kindly help.
this is what i get on doing c:\adb>fastboot getvar all
INFOversion: 0.5
INFOversion-bootloader: 1.27.1100
INFOversion-baseband: N/A
INFOversion-cpld: None
INFOversion-microp: None
INFOversion-main: 3.32.401.5
INFOserialno: SH1AJV804923
INFOimei: 358313047099531
INFOproduct: pyramid
INFOplatform: HBOOT-8260
INFOmodelid: PG5813001
INFOcidnum: HTC__038
INFObattery-status: good
INFObattery-voltage: 3811mV
INFOpartition-layout: Generic
INFOsecurity: off
INFObuild-mode: SHIP
INFOboot-mode: FASTBOOT
INFOcommitno-bootloader: 617f0a98
INFOhbootpreupdate: 11
INFOgencheckpt: 0
all: Done!
finished. total time: 0.499s

reresp same
im having a similar problem - does anyone know what the solution was
edit: pretty much the same thing
stuck with the fastboot/cwr but can't get anything else to work
tried multiple RUU already

xenonxeno said:
i just tried to flash my htc sensation xe for the first time, i successfully did S-OFF using the revolutionary tool and then tried to install ClockworkMod Recovery from PG58IMG.zip which succeeded,
but i havent been able to boot up the device since doing that. its stuck on the htc logo. kindly help.
this is what i get on doing c:\adb>fastboot getvar all
INFOversion: 0.5
INFOversion-bootloader: 1.27.1100
INFOversion-baseband: N/A
INFOversion-cpld: None
INFOversion-microp: None
INFOversion-main: 3.32.401.5
INFOserialno: SH1AJV804923
INFOimei: 358313047099531
INFOproduct: pyramid
INFOplatform: HBOOT-8260
INFOmodelid: PG5813001
INFOcidnum: HTC__038
INFObattery-status: good
INFObattery-voltage: 3811mV
INFOpartition-layout: Generic
INFOsecurity: off
INFObuild-mode: SHIP
INFOboot-mode: FASTBOOT
INFOcommitno-bootloader: 617f0a98
INFOhbootpreupdate: 11
INFOgencheckpt: 0
all: Done!
finished. total time: 0.499s
Click to expand...
Click to collapse
What is the last rom you had?
You can still go to bootloader thus you can go to recovery...
So enter recovery and tell me whether you are able to e ter or not
Sent from my pyramid.. Through blazing fast sonic waves

w00dberry said:
im having a similar problem - does anyone know what the solution was
edit: pretty much the same thing
stuck with the fastboot/cwr but can't get anything else to work
tried multiple RUU already
Click to expand...
Click to collapse
You mean you succesfully flashed RUU and still can't boot?
Sent from my pyramid.. Through blazing fast sonic waves

xenonxeno said:
i just tried to flash my htc sensation xe for the first time, i successfully did S-OFF using the revolutionary tool and then tried to install ClockworkMod Recovery from PG58IMG.zip which succeeded,
but i havent been able to boot up the device since doing that. its stuck on the htc logo. kindly help.
this is what i get on doing c:\adb>fastboot getvar all
INFOversion: 0.5
INFOversion-bootloader: 1.27.1100
INFOversion-baseband: N/A
INFOversion-cpld: None
INFOversion-microp: None
INFOversion-main: 3.32.401.5
INFOserialno: SH1AJV804923
INFOimei: 358313047099531
INFOproduct: pyramid
INFOplatform: HBOOT-8260
INFOmodelid: PG5813001
INFOcidnum: HTC__038
INFObattery-status: good
INFObattery-voltage: 3811mV
INFOpartition-layout: Generic
INFOsecurity: off
INFObuild-mode: SHIP
INFOboot-mode: FASTBOOT
INFOcommitno-bootloader: 617f0a98
INFOhbootpreupdate: 11
INFOgencheckpt: 0
all: Done!
finished. total time: 0.499s
Click to expand...
Click to collapse
Flash an ICS ROM. Your GB ROM will not boot on 3.32 firmware.
---------- Post added at 11:28 AM ---------- Previous post was at 11:26 AM ----------
w00dberry said:
im having a similar problem - does anyone know what the solution was
edit: pretty much the same thing
stuck with the fastboot/cwr but can't get anything else to work
tried multiple RUU already
Click to expand...
Click to collapse
I need a better description of the problem.
"It doesn't work" "I tried multiple RUUs" are useless to me.
What happens when you flash the RUU? Is it successful?

[Q] Problems installing firmware

Hello, sry if this has already been askedbut I'm a noob so... Untill now I had cyanogenmod 7.1 on my sensation and i wanted to switch to OpenSensation but I needed to install the latest firmware for that! So I tried doing what they said on theandroidsoul.com/how-to-flash-pg58img-zip-ics-firmware-on-htc-sensation/ but had no success. Now every time i try to start the phone it just gets stuck at the cyanogenmod9 boot animation! I tried restoring from NANDroid backup but then it gets stuck on the cyanogenmod7 boot animation!
If anyone could help me fix this I'd be very grateful!
EDIT: I also can't install cyanogenmod 7.1 again!

mankiboss said:
Hello, sry if this has already been askedbut I'm a noob so... Untill now I had cyanogenmod 7.1 on my sensation and i wanted to switch to OpenSensation but I needed to install the latest firmware for that! So I tried doing what they said on theandroidsoul.com/how-to-flash-pg58img-zip-ics-firmware-on-htc-sensation/ but had no success. Now every time i try to start the phone it just gets stuck at the cyanogenmod9 boot animation! I tried restoring from NANDroid backup but then it gets stuck on the cyanogenmod7 boot animation!
If anyone could help me fix this I'd be very grateful!
Click to expand...
Click to collapse
more details please
complete HBOOT details
also if you have adb/fastboot installed
then post the output of this command except imei and serial number
fastboot getvar all
once you post the output
then we can guide you further

S-OFF, HBOOT-1.27.1100, RADIO-10.14.9035.01_M
C:\Users\Roncevic\Downloads\ADB_Fastboot_Windows>fastboot getvar all
< waiting for device >
INFOversion: 0.5
INFOversion-bootloader: 1.27.1100
INFOversion-baseband: 10.14.9035.01_M
INFOversion-cpld: None
INFOversion-microp: None
INFOversion-main: 1.45.531.1
INFOserialno:
INFOimei:
INFOproduct: pyramid
INFOplatform: HBOOT-8260
INFOmodelid: PG5813000
INFOcidnum: HTC__032
INFObattery-status: low
INFObattery-voltage: 3497mV
INFOpartition-layout: Generic
INFOsecurity: off
INFObuild-mode: SHIP
INFOboot-mode: FASTBOOT
INFOcommitno-bootloader: 617f0a98
INFOhbootpreupdate: 11
INFOgencheckpt: 0
all: Done!
finished. total time: 0.491s
C:\Users\Roncevic\Downloads\ADB_Fastboot_Windows>

mankiboss said:
S-OFF, HBOOT-1.27.1100, RADIO-10.14.9035.01_M
C:\Users\Roncevic\Downloads\ADB_Fastboot_Windows>fastboot getvar all
< waiting for device >
INFOversion: 0.5
INFOversion-bootloader: 1.27.1100
INFOversion-baseband: 10.14.9035.01_M
INFOversion-cpld: None
INFOversion-microp: None
INFOversion-main: 1.45.531.1
INFOserialno:
INFOimei:
INFOproduct: pyramid
INFOplatform: HBOOT-8260
INFOmodelid: PG5813000
INFOcidnum: HTC__032
INFObattery-status: low
INFObattery-voltage: 3497mV
INFOpartition-layout: Generic
INFOsecurity: off
INFObuild-mode: SHIP
INFOboot-mode: FASTBOOT
INFOcommitno-bootloader: 617f0a98
INFOhbootpreupdate: 11
INFOgencheckpt: 0
all: Done!
finished. total time: 0.491s
C:\Users\Roncevic\Downloads\ADB_Fastboot_Windows>
Click to expand...
Click to collapse
thanks that explains what caused the problem
I'll try to explain it briefly
now typically our sensation can be broken into three parts like (it may not be 100% correct but its an analogy to explain the firmware things)
hardware/device ---------------->>> firmware(HBOOT + radio) --------------------->>>ROM (ICS/GB)
so for it to run properly
you need to have GB firmware for GB rom (GB- ginger bread)
or ICS firmware for ICS rom
otherwise it wont work
now in your case
you hboot is 1.27.1100 (ICS one) but the radio is still of GB one (10.14.xx)
and
from "INFOversion-main: 1.45.531.1" this we can say that you are running a GB os ..and i think its cm7.1 that you restored
now you might have understood why you are looping
your firmware upgrade is half complete ( 1 part is of ICS one and other is of GB one)
and you are running GB rom..which wont work
so now you have two ways out
1.to have cm9 (ICS rom)
you need to properly flash the 3.32 firmware first (ICS compatible)
that you can find it here (get the universal 3.32 firmware )
universal firmwares
then flash the cm9 via recovery ..voila you are done
(for safe side you can check you flashed fw properly or not ...hboot should be 1.27.xx and radio should be 11.xx )
2.to have back the cm7.1 (GB rom)
here you need to flash the GB firmware
get the universal 1.17 firmware from the above linked thread and flash it
(verify the 1.17 firmware by looking at hboot (1.17.xx) and radio (10.xx))
then restore you cm7.1 backup ..and you are done again
NOTE: remember to remove the PG58IMG zip file from sdcard after flashing otherwise you cant go into bootloader/fastboot

What he said do that as well you might want to get supercid it makes things easier...
Swyped From My Sensation.

I tried doing what you said but i it says wrong CID and sometimes battery voltage too low! If i really got the wrong file how can i put the right file on the SD card with fastboot or sth and do I need to change the battery? thx

mankiboss said:
I tried doing what you said but i it says wrong CID and sometimes battery voltage too low! If i really got the wrong file how can i put the right file on the SD card with fastboot or sth and do I need to change the battery? thx
Click to expand...
Click to collapse
get the 3.32 universal firmware (NON TMOUS) one and flash it
if you want gingerbread rom flash the 1.17 universal firmware (NON TMOUS one)
firmware thread
that should solve your wrong cid problem
if it still persists
then do a supercid
commands to supercid
1.fastboot getvar cid (store/remember your original cid)
2.fastboot oem writecid 11111111 (eight ones)
3.fastboot reboot-bootloader
4.fastboot getvar cid (verify your cid now)

I did the superCID but it still says battery voltage too low. Do I have to change the battery?

mankiboss said:
I did the superCID but it still says battery voltage too low. Do I have to change the battery?
Click to expand...
Click to collapse
of course you need to charge the battery
if while doing firmware upgrade ..your phone got switched off ..due to less battery ..it can potentially lead to a brick
ALWAYS when flashing a firmware ..you need to have enough battery (atleast 40-50% imho)

[Q] RUU needed for Orange/EE HTC One SV

Hi everyone,
HTC One SV LTE (K2_UL) on Orange (it's about 2 years old)
Not rooted
S-ON
Phone was on 4.2.2
USB debugging is not enabled
I'm pretty technical and have scoured forums for the last couple of days and still haven't found a solution to the problem I have with my HTC One SV.
I left the phone on charge overnight and the next day I was presented with a screen asking me to decrypt storage. The phone was never rooted or tampered with.
The problem I have is that I'm unable to factory reset the phone or even get into recovery. Clearing storage doesn't make any difference.
Every time I try, the phone resets and takes me to the "please enter password to decrypt" screen. It appears that the internal SD storage or at least a directory is corrupt.
One solution is to run an Orange RUU to resotre to factory default but I can't fine one anywhere, and I could really do with one.
I'm able to run fastboot commands, but adb does not see the phone as a device.
Can anyone help?

I don't know, how that happened and i don't really have a (easy) solution.
But i guess you won't get it done without an unlocked bootloader and an recovery like Twrp.
A search broughr up similar problems on other devices: http://forum.xda-developers.com/showthread.php?t=2749625

old.splatterhand said:
I don't know, how that happened and i don't really have a (easy) solution.
But i guess you won't get it done without an unlocked bootloader and an recovery like Twrp.
A search broughr up similar problems on other devices: http://forum.xda-developers.com/showthread.php?t=2749625
Click to expand...
Click to collapse
Another thing worth mentioning is that when I try to run fastboot -w I get "Erasing 'userdata' ... FAILED (remote: not allowed)
I'm a pretty technical person (10+Years in IT) but I get the feeling that without the RUU to completely wipe it I won't be able to get this phone fixed.

I don't think, the RUU you are talking is available!
One idea could be:
-Unlock your bootloader
-flash TWRP
-try if you can get something done in recovery, if not,
-flash a stock rom
-get S-off with rumrunner.us
-downgrade hboot
-get Supercid
-run the WWE RUU (and debrand your device)

Is there anyone there who could help me? Does anyone have access or can send me a link to an Orange HTC One SV LTE RUU.exe ??

Well, let's give it a try and ask @djluisbento
Can you obtain a RUU for HTC One SV (K2_ul), Android 4.2.2, Orange/EE branded?
@geileskey
What was the software number your HTC One SV was running on?

old.splatterhand said:
Well, let's give it a try and ask @djluisbento
Can you obtain a RUU for HTC One SV (K2_ul), Android 4.2.2, Orange/EE branded?
@geileskey
What was the software number your HTC One SV was running on?
Click to expand...
Click to collapse
This is what I got from Fastboot:
INFOversion: 0.5
INFOversion-bootloader: 2.21.0000
INFOversion-baseband: N/A
INFOversion-cpld: None
INFOversion-microp: None
INFOversion-main: 3.11.61.10
INFOversion-misc: PVT SHIP S-ON
INFOmeid:
INFOproduct: k2_ul
INFOplatform: HBOOT-8930
INFOmodelid: PL8010000
INFOcidnum: ORANG001
INFObattery-status: good
INFObattery-voltage: 4162mV
INFOpartition-layout: Generic
INFOsecurity: on
INFObuild-mode: SHIP
INFOboot-mode: FASTBOOT
INFOcommitno-bootloader: dirty-2bb255c2
INFOhbootpreupdate: 11
INFOgencheckpt: 0
thanks,
Mike

geileskey said:
This is what I got from Fastboot:
Click to expand...
Click to collapse
Remove serialno & imei and highlight INFOversion-main: 3.11.61.10
And then lets see, if @djluisbento will answer.

old.splatterhand said:
Remove serialno & imei and highlight INFOversion-main: 3.11.61.10
And then lets see, if @djluisbento will answer.
Click to expand...
Click to collapse
INFOversion: 0.5
INFOversion-bootloader: 2.21.0000
INFOversion-baseband: N/A
INFOversion-cpld: None
INFOversion-microp: None
INFOversion-main: 3.11.61.10
INFOversion-misc: PVT SHIP S-ON
INFOmeid:
INFOproduct: k2_ul
INFOplatform: HBOOT-8930
INFOmodelid: PL8010000
INFOcidnum: ORANG001
INFObattery-status: good
INFObattery-voltage: 4162mV
INFOpartition-layout: Generic
INFOsecurity: on
INFObuild-mode: SHIP
INFOboot-mode: FASTBOOT
INFOcommitno-bootloader: dirty-2bb255c2
INFOhbootpreupdate: 11
INFOgencheckpt: 0

geileskey said:
INFOversion: 0.5
INFOversion-bootloader: 2.21.0000
INFOversion-baseband: N/A
INFOversion-cpld: None
INFOversion-microp: None
INFOversion-main: 3.11.61.10
INFOversion-misc: PVT SHIP S-ON
INFOmeid:
INFOproduct: k2_ul
INFOplatform: HBOOT-8930
INFOmodelid: PL8010000
INFOcidnum: ORANG001
INFObattery-status: good
INFObattery-voltage: 4162mV
INFOpartition-layout: Generic
INFOsecurity: on
INFObuild-mode: SHIP
INFOboot-mode: FASTBOOT
INFOcommitno-bootloader: dirty-2bb255c2
INFOhbootpreupdate: 11
INFOgencheckpt: 0
Click to expand...
Click to collapse
I've meant, remove it from the post # 7

old.splatterhand said:
I've meant, remove it from the post # 7
Click to expand...
Click to collapse
Sorry! Just made the edit

old.splatterhand said:
Well, let's give it a try and ask @djluisbento
Can you obtain a RUU for HTC One SV (K2_ul), Android 4.2.2, Orange/EE branded?
@geileskey
What was the software number your HTC One SV was running on?
Click to expand...
Click to collapse
Hello,
I already have the version 3.11.61.10 and 3.11.401.1 and i gonna upload it.

I'm new to this forum, would it be available as a link or a PM?
Many thanks, Mike.

geileskey said:
I'm new to this forum, would it be available as a link or a PM?
Many thanks, Mike.
Click to expand...
Click to collapse
Usually he shared it as a link for all.
@djluisbento
It would be really great if you could also upload the RUU for k2_u with Android 4.2.2 and software number 3.11.401.106 :highfive:

old.splatterhand said:
Usually he shared it as a link for all.
@djluisbento
It would be really great if you could also upload the RUU for k2_u with Android 4.2.2 and software number 3.11.401.106 :highfive:
Click to expand...
Click to collapse
I gonna Upload it for all.

https://drive.google.com/file/d/0B17smFr95pleUEw0SFRzemdhVVU/view?usp=sharing
https://drive.google.com/file/d/0B17smFr95pleZ3VlT1dOZ25fV0E/view?usp=sharing

djluisbento said:
https://drive.google.com/file/d/0B17smFr95pleUEw0SFRzemdhVVU/view?usp=sharing
https://drive.google.com/file/d/0B17smFr95pleZ3VlT1dOZ25fV0E/view?usp=sharing
Click to expand...
Click to collapse
I downloaded both, but the "PL80IMG_K2_UL_JB422_SENSE50_MR_Orange_UK_3.11.61.10_Radio_1.18.40a.00.05_10.81a.40.23_release_340236_signed.zip" only extracts to 98.1K even though the ZIP file is 665MB is there something wrong with the ZIP file?
thanks,
Mike

geileskey said:
I downloaded both, but the "PL80IMG_K2_UL_JB422_SENSE50_MR_Orange_UK_3.11.61.10_Radio_1.18.40a.00.05_10.81a.40.23_release_340236_signed.zip" only extracts to 98.1K even though the ZIP file is 665MB is there something wrong with the ZIP file?
thanks,
Mike
Click to expand...
Click to collapse
I'm also a complete noob to RUU flashing. I thought the ZIPs would contain an executable, but neither of them have an RUU.exe file in them. Am I doing something wrong?

The Ruu is encryted, thats why you can't extract. And you don't need to!
Bootloader must be locked!
Rename the Orange zip to PL80IMG.zip, copy it to external sdcard, boot your phone to bootloader and let it search for files to update. It will ask you, if you wat to flash the zip, confirm with Vol+ and follow the instructions.
@djluisbento
Any news about the RUU for k2_u with Android 4.2.2 and software number 3.11.401.106?

old.splatterhand said:
The Ruu is encryted, thats why you can't extract. And you don't need to!
Rename the Orange zip to PL80IMG.zip, copy it to external sdcard, boot your phone to bootloader and let it search for files to update. It will ask you, if you wat to flash the zip, confirm with Vol+ and follow the instructions.
@djluisbento
Any news about the RUU for k2_u with Android 4.2.2 and software number 3.11.401.106?
Click to expand...
Click to collapse
For the moment i do't have it. only the older version.

Htc One M8 network problem

My HTC One M8 from Verizon got messed up when i loaded a custom rom on it. It lost IMEI,baseband and the necessary stuff to make it detect network.
I tried getting the info in fastboot and found out that the IMEI is still somewhere in the phone.
Please HELP...
I am unable to post fastboot log now but i will do that as soon as i can, my HTC bootloader has been unlocked and s-off. TIA
Here is the fastboot log
INFOversion: 0.5
INFOversion-bootloader: 3.19.0.0000
INFOversion-baseband: 1.15.2133156.UA13G
INFOversion-cpld: None
INFOversion-microp: None
INFOversion-main: 4.19.707.2
INFOversion-misc: PVT SHIP S-OFF
INFOserialno: ***********
INFOimei: *************
INFOimei2: Not Support
INFOmeid: 00000000000000
INFOproduct: m8_wlv
INFOplatform: hTCBmsm8974
INFOmodelid: 0P6B2****
INFOcidnum: 11111111
INFObattery-status: good
INFObattery-voltage: 0mV
INFOpartition-layout: Generic
INFOsecurity: off
INFObuild-mode: SHIP
INFOboot-mode: FASTBOOT
INFOcommitno-bootloader: 3aa067db
INFOhbootpreupdate: 11
INFOgencheckpt: 0
all: Done!
Mod Edit: removed sensitive information.

I had the same problem. The solution is flash " DOTTAT_VZWM8_S_OFF_SF_6.0_RUU.zip " from here https://ga1.androidfilehost.com/dl/...5911973442/DOTTAT_VZWM8_S_OFF_SF_6.0_RUU.zip? .
Once that you have downloades the file change the name to "0P6BDIAG.zip". Then you have to put file in your SD Card and boot on hboot. It is going to check the file and ask you if you want to flash it. When finish it and restart, you are going to have network working again. Best regards

I get invalid img error;seems file is corrupt

Adebayo0437 said:
I get invalid img error;seems file is corrupt
Click to expand...
Click to collapse
Yep buddy that's it ?. Corrupt.
Sent from my HTC6545LVW using Tapatalk

dottat said:
Yep buddy that's it . Corrupt.
Sent from my HTC6545LVW using Tapatalk
Click to expand...
Click to collapse
What that supposed to mean?

Adebayo0437 said:
What that supposed to mean?
Click to expand...
Click to collapse
means the file was corrupt or got corrupted during download. if you can find an RUU you should be able to use fastboot to flash it

Adebayo0437 said:
What that supposed to mean?
Click to expand...
Click to collapse
Translation: re-download and try again.
And try not to knock a developer by saying he's posting corrupt files. Files sometimes lose information during download, which would cause them not to work. This is usually the problem.
You could avoid this by checking md5 after every download and comparing it to the posted one on his website. Match = good to flash.
Good luck.