Related
ok i need help please , i had gbread on it and installed superoneclick to get root then tried to flash cwm with vipermod. message said out of storage space or something (dont have ext mem only internal)and now phone will not turn on.
have followed this guide http://forum.xda-developers.com/showthread.php?t=1244490 and phone was recognised by omapp but couldnt change the port in device manager and couldnt find a bin to download so i tried to flash a kdz v21a
clicked start on lgflasher but nothing happened so after about 5 mins i cancelled it thinking without the port change it was a waste of time.
now i cant even get omapp to flash up when i connect phone . device manager refreshes but i cant see anything change .
hope thats enough info for some kind person to help.
many thanks in advance
marty
Try this start on step 3 its in the thrill forum but they are the same phone http://forum.xda-developers.com/showthread.php?t=1491870
sent from my acidhazard thrill
marty41 said:
...then tried to flash cwm with vipermod...
marty
Click to expand...
Click to collapse
Where did you get vipermod from? The Transformer Prime forums? That's meant for the TFP and would not have worked with the O3D since it flashes to mmcblk0p4 rather than mmcblk0p. You should have used the flasher here.
Download this, this and this. Extract smartflash.zip, install both driver packages. Then, run Windows Enabler, in the notifications bar, click it and make sure it is set to 'on'.
Now remove your phone's battery and sim card, press volume up and connect your phone to the computer. Hold volume up until it is detected by the computer. It should take no longer than 20 seconds.
Now run B_SmartFlashTool_Extern.exe, go to rom copy d/l, select LGP920_CP.fls for CP bin and LGP920_AP.bin for AP bin. Make sure under communications setup that your phone is connected (verify the com port in device manager) and then click start. If all goes well, you'll have a stock v21D phone again
Thanks for the help guys but i'm not getting a com port when i connect the phone so i don't think i can use any of those methods . or can i
i want to go back to the beginning and see if omapp will detect phone and install drivers but i can uninstall the installer but dont think that will remove the drivers , does anyone know how to do that.(cos i think i messed that bit up )
thanks again
marty
vipermod , i think i followed a link somewhere in the o3d forum where someone said u could use it to flash cwm
so , i uninstalled all lg drivers uninstalled omap installer searched registry for for any mention of omap and deleted (some wouldnt delete ) .
restarted computer (xp by the way )
then installed omap installer and lg drivers and connected phone holding vol up
and................. NOTHING whereas yesterday i had a little icon in the task bar and the opportunity to install omap drivers.
conclusion , phone is dead , i had an oppurtunity to fix it yesterday and i blew it
hope someone tells me i'm wrong but its not looking good
marty
take off battery and just put your usb cable and tell us if it shows omap in your device manager
dont press keys
if i connect phone without battery device manager just refreshes a couple of times but nothing changes with regards to ports doesn't matter if i have vol+ button in power button in or nothing
thanks anyway
marty
am i getting somewhere
update : ok so i'm on a clean install of xp and i connected the phone with vol+ and it wants to install omap4430 drivers. is that good news?
i installed omapinstaller , then the 2 lg drivers ca and ma , then reconnected the phone and went thro omap driver install but still don't have any ports in device manager
is there no way i can force it to flash without it having to think it is connected cause if its recognising it as omap4430 there must be something there
don't want to give up on it too easy , if only i put this much effort into it whilst it was working lol
marty
evening all . new update
tonight i've installed the lg support tool and drivers and found that if i leave my phone connected i occasionally get "TI sample boards" popping up in device manager for a couple of seconds without having to press buttons , unfortunately it doesn't stay on for any longer with buttons pressed.
i was wondering how to force install the "LG CDMA composite usb device " drivers cos its never asking for them as it should according to the tutorial
hope someone can help cos i've seen a few threads with same problem as me
marty
OMAP4430 driver, can't install, doesn't recognize files to install them?
following this guide http://forum.xda-developers.com/showthread.php?t=1244490 to flash my bricked LG, after I reach stop where I need to install OMAP4430 drivers with selecting folder where drivers are located, it says that can't find anything. Also it constantly connects and disconnects, any solution to this issue?
Running on Windows 7 x64
Listen drivers should be there or reinstall omap drivers ..about the connect disconnect am using the Sam windows and it happens here too but flashing works but make sure to install the drivers
sent from my lg o3d
a piece of advice:
don't ask alot ..go read.
well OMAPFlash driver shows on programs and features, but it constantly connects disconnects OMAP4430 in device manager, tried to select folder, but it just disconnects to quick that it ignores my previously selected paths.
I can't flash it, because I can't find that start_fastboot app
/ another issue, if I ignore that OMAP4430 and just carry on step by step, change port to 41 for CDMA and open LGFlashTool.exe for , it just wont open, tried even on xp sp3, still nothing... it's 1.1 version.
^^^^^ scratch that, works now with 1.2 version
now have a question, If I have 170mb kdz for 21e, can I use it in FlashTool? Because to download BIN_LGP920AT-00-V21e-EUR-XXX-Apr-19-2012 , it's gonna be another hour, because where file was uploaded, download speed is so slow...........
I'm running on windows 7 x64
OMAP drivers still was bugged for me, eventho I tried lots of ways to fix it.
eventually, I used smart flash with 21e AP and CP and it flashes successfully
P.S. I do put back battery when flashing starts, otherwise ,it restarts at partition part!!!
about kzd just Google lge kdz ectractor and go read xbsalls ressurection thread again to fix omap flashing too fast.
sent from my lg o3d
a piece of advice:
don't ask alot ..go read.
Help!
I have the LG Security Error at boot. My phone doesn't even load drivers on my PC with Windows 7. Therefore, no fastboot option. I'm using LG Optimus L9. I got the error after trying to install a custom recovery that was supposed to be for a locked bootloader. I guess I may be screwed. Hope someone can help. Thanks!
Omap4430 driver error
daGUCCI said:
well OMAPFlash driver shows on programs and features, but it constantly connects disconnects OMAP4430 in device manager, tried to select folder, but it just disconnects to quick that it ignores my previously selected paths.
I can't flash it, because I can't find that start_fastboot app
/ another issue, if I ignore that OMAP4430 and just carry on step by step, change port to 41 for CDMA and open LGFlashTool.exe for , it just wont open, tried even on xp sp3, still nothing... it's 1.1 version.
^^^^^ scratch that, works now with 1.2 version
now have a question, If I have 170mb kdz for 21e, can I use it in FlashTool? Because to download BIN_LGP920AT-00-V21e-EUR-XXX-Apr-19-2012 , it's gonna be another hour, because where file was uploaded, download speed is so slow...........
I'm running on windows 7 x64
OMAP drivers still was bugged for me, eventho I tried lots of ways to fix it.
eventually, I used smart flash with 21e AP and CP and it flashes successfully
P.S. I do put back battery when flashing starts, otherwise ,it restarts at partition part!!!
Click to expand...
Click to collapse
I'm also having this same problem with my lg, it disconnect and connect from device manager menu.
And I can't flash it using lg flash tool because its not stable during read. Any solution to this ???????
Help, I cant root it nor use lg flash tool because the usb is recognized as cosmo driver and I need to find the driver software.
Also, I cant seem to get signal since I cant use lgflash tool to flash baseband... Any ideas how?
I can access the sd card though. When I remove the battery and pressed the Vol up button, the OMAP driver keep connect and disconnect too and I cant seemed to install it, I'm using windows 7 bytheway.
Baseband is not XBSA404 but instead its the original korean baseband. I can't flash any baseband too.
This doesn't belong here..
However...
Cosmo drivers = omap4430 drivers
so just install the omap drivers like you did before to flash ics.
Edit: for the connect/disconnect problem..
Just keep battery in, hold vol+ and connect usb (hold vol+ until you see s/w)
Sent from my P920 using XBSA ICS V5
Thanks
TMProduct1onZ said:
This doesn't belong here..
However...
Cosmo drivers = omap4430 drivers
so just install the omap drivers like you did before to flash ics.
Edit: for the connect/disconnect problem..
Just keep battery in, hold vol+ and connect usb (hold vol+ until you see s/w)
Sent from my P920 using XBSA ICS V5
Click to expand...
Click to collapse
Thanks, but I cant seemed to install the OMAP Driver even b4 installing ICS. It just says windows cannot find.... I tried doing this manually but still get the same respond. Also when I try to flash back to my original rom, it keep restarting it over and over again at lg logo. The Lg logo last abot halve a sec b4 restarting. So I did reflash back to ICS and it works. But still no network etc...
fadhli7 said:
Thanks, but I cant seemed to install the OMAP Driver even b4 installing ICS. It just says windows cannot find.... I tried doing this manually but still get the same respond. Also when I try to flash back to my original rom, it keep restarting it over and over again at lg logo. The Lg logo last abot halve a sec b4 restarting. So I did reflash back to ICS and it works. But still no network etc...
Click to expand...
Click to collapse
Some tips.
Need to use twrp recovery to install stuff. Cwm uses vol+, twrp vol- to enter recovery(or was it vice versa). Cwm old version doesnt work with xbsa404.
I had brick also, lg logo and reboot. WIn 7 found lg serial port. Used flashtool and change port to 41 or if it is that change to 42.
Then flasher should found lg and flash it.
To get network you need new kernel.
OK!
kalamake said:
Some tips.
Need to use twrp recovery to install stuff. Cwm uses vol+, twrp vol- to enter recovery(or was it vice versa). Cwm old version doesnt work with xbsa404.
I had brick also, lg logo and reboot. WIn 7 found lg serial port. Used flashtool and change port to 41 or if it is that change to 42.
Then flasher should found lg and flash it.
To get network you need new kernel.
Click to expand...
Click to collapse
The thing is when I flash to ICS, my recovery is gone plus after I reflashed to ICS, the phone will froze for a few seconds and then back to normal. This keeps repeating.... Also if ur talking abt rooting, I cant coz it says invalid ap path.
fadhli7 said:
Help, I cant root it nor use lg flash tool because the usb is recognized as cosmo driver and I need to find the driver software.
Also, I cant seem to get signal since I cant use lgflash tool to flash baseband... Any ideas how?
I can access the sd card though. When I remove the battery and pressed the Vol up button, the OMAP driver keep connect and disconnect too and I cant seemed to install it, I'm using windows 7 bytheway.
Baseband is not XBSA404 but instead its the original korean baseband. I can't flash any baseband too.
Click to expand...
Click to collapse
I dont really understand where you stuck exactely and what you did but regarding the cosmo driver:
To install the cosmo drivers for windows xp I downloaded and installed the lg pc suite software ver. 4 something and my phone was connected to the pc under software installation.
For win 7 64bit the driver was automatically installed by windows but you can try lg pc suite with win 7 too.
Sent from my GT-N8000 using XDA Premium HD app
ferel said:
I dont really understand where you stuck exactely and what you did but regarding the cosmo driver:
To install the cosmo drivers for windows xp I downloaded and installed the lg pc suite software ver. 4 something and my phone was connected to the pc under software installation.
For win 7 64bit the driver was automatically installed by windows but you can try lg pc suite with win 7 too.
Sent from my GT-N8000 using XDA Premium HD app
Click to expand...
Click to collapse
Whenever I wanna root my phone, it says cannot find specific file or folder. Plus I can install wkpark boot because I cant install the OMAP driver eventhough I directed it manually. When I tried on other laptop, I managed to successfully install the driver, but it still connect and disconnect ( u can hear by the sound ).
fadhli7 said:
Whenever I wanna root my phone, it says cannot find specific file or folder. Plus I can install wkpark boot because I cant install the OMAP driver eventhough I directed it manually. When I tried on other laptop, I managed to successfully install the driver, but it still connect and disconnect ( u can hear by the sound ).
Click to expand...
Click to collapse
What do you do exactely and what is the error message exactely pls.
For the root you need the lge cosmo driver.
It is correct this wy... connect and disconnect all the time. It means it is ok if you installed the driver.
To install those omap drivers you either needs to be fast to click on them when the ti omap appears or there is a solution to see the already attached devices in thr windows decice list, I saw it somewhere here but i do not remember in which thread.
Sent from my GT-N8000 using XDA Premium HD app
you can get OMAP4430 driver by downloading wkparks fastboot loader from http://forum.xda-developers.com/showthread.php?t=1971014
extract it and you should find it on usb_drv_windows
to install it you can follow this guide http://forum.xda-developers.com/showpost.php?p=32955612&postcount=3 which taken from http://forum.xda-developers.com/showthread.php?t=1942836
good luck
satubsatub said:
you can get OMAP4430 driver by downloading wkparks fastboot loader from http://forum.xda-developers.com/showthread.php?t=1971014
extract it and you should find it on usb_drv_windows
to install it you can follow this guide http://forum.xda-developers.com/showpost.php?p=32955612&postcount=3 which taken from http://forum.xda-developers.com/showthread.php?t=1942836
good luck
Click to expand...
Click to collapse
Yup, I tried installing the driver many times but to no avail... Thanks for the help anyway... :good:
Hi guys, I have a problem, I did a factory reset on my rooted LG Thrill 4G / Optimus 3D with ICS. when it reboot, I get the TWRP menu and I dont know what to do, I'm desperate I cant use the phone in that condition, I have tried almost all the options but nothing works. can someone help me?
Im new in this
Josesanchez21 said:
Hi guys, I have a problem, I did a factory reset on my rooted LG Thrill 4G / Optimus 3D with ICS. when it reboot, I get the TWRP menu and I dont know what to do, I'm desperate I cant use the phone in that condition, I have tried almost all the options but nothing works. can someone help me?
Im new in this
Click to expand...
Click to collapse
Flashing ics the .bin .fls
Check your xda messages. I sent you a PM.
I am not sure what all you did, but if factory hard reset does not fix your issue, you can usually flash a firmware to bring back your device
http://forum.xda-developers.com/showthread.php?p=39269819
It could be you just need to flash just a bootloader, but like I say, I am not sure what you did.
EDIT: since you can access twrp, it would be easier to install ICS by installing .zip files from this thread
http://forum.xda-developers.com/showthread.php?p=39130435
Do 1-3... install ICS as in #2 there and boot125 as in step 3, then reboot phone (you will need to copy the files to a micro sd by plugging one into a pc by an adapter). That is one way that would be 'easier' than setting up LG Flash Tool. If TWRP cannot find your external micro sd, you may need to proceed as I mention above.
hard reset
Josesanchez21 said:
Hi guys, I have a problem, I did a factory reset on my rooted LG Thrill 4G / Optimus 3D with ICS. when it reboot, I get the TWRP menu and I dont know what to do, I'm desperate I cant use the phone in that condition, I have tried almost all the options but nothing works. can someone help me?
Im new in this
Click to expand...
Click to collapse
try to make hard reset like this http://forum.xda-developers.com/showthread.php?t=2337545&page=5
in step 3 or flash rom :cyclops:
I forgot
My lg Optimus 3D is Lg p925 if i try p920 it will work anyway? and also TWRP says that I dont Have OS
The ICS?
drastic00 said:
Check your xda messages. I sent you a PM.
I am not sure what all you did, but if factory hard reset does not fix your issue, you can usually flash a firmware to bring back your device
http://forum.xda-developers.com/showthread.php?p=39269819
It could be you just need to flash just a bootloader, but like I say, I am not sure what you did.
EDIT: since you can access twrp, it would be easier to install ICS by installing .zip files from this thread
http://forum.xda-developers.com/showthread.php?p=39130435
Do 1-3... install ICS as in #2 there and boot125 as in step 3, then reboot phone (you will need to copy the files to a micro sd by plugging one into a pc by an adapter). That is one way that would be 'easier' than setting up LG Flash Tool. If TWRP cannot find your external micro sd, you may need to proceed as I mention above.
Click to expand...
Click to collapse
the ICS as in #2 is the V30A file?
error flashing
Josesanchez21 said:
the ICS as in #2 is the V30A file?
Click to expand...
Click to collapse
Error flashing
I suspect drivers are not installed correctly. Check part 1 very carefully.
You must install the .bin of v28B first by Flash Tool. That will install the OS. If and when you then decide to install an xbsa rom from TWRP, v8 changes it to v30A. vR3D is v30C (that one requires the large partition v28B).
Factory reset should not have done this to your phone
yeah I think it was my fault
drastic00 said:
I suspect drivers are not installed correctly. Check part 1 very carefully.
You must install the .bin of v28B first by Flash Tool. That will install the OS. If and when you then decide to install an xbsa rom from TWRP, v8 changes it to v30A. vR3D is v30C (that one requires the large partition v28B).
Factory reset should not have done this to your phone
Click to expand...
Click to collapse
yeah I think it was my fault after all XD
if I send you a video?
drastic00 said:
I suspect drivers are not installed correctly. Check part 1 very carefully.
You must install the .bin of v28B first by Flash Tool. That will install the OS. If and when you then decide to install an xbsa rom from TWRP, v8 changes it to v30A. vR3D is v30C (that one requires the large partition v28B).
Factory reset should not have done this to your phone
Click to expand...
Click to collapse
If i send you a video showing what is my problem, you will get any idea of how to repair it? sorry for bad english :silly: heres the video link: http://www.youtube.com/watch?v=YLbKqzSLB-g
Are you on Windows 7?
I would more than video like to see a screen shot of the drivers in your pc Device Manager (when phone is connected to pc by usb, you hold volume up on phone when you plug it in).
There should be 'omap 4430' in 'other devices' in pc Device Manager. If correctly installed, it should NOT be flashing/blinking on and off. You must use the driver from the wkpark Fastboot package, not the one from the 'omap4flash installer' pack.
There are also two LG drivers that must be installed to pc. And there should be LG Cosmo device appearing in Device Manager someplace also, port set to 41.
I ask because driver install can be tricky or difficult, and confusing when you first do all of that. And, it is very important to have it all correct to flash successfully. Usually it is the problem when flash will not complete or start.
It also adds to difficulty that you must translate the instructions...
just one driver
drastic00 said:
Are you on Windows 7?
I would more than video like to see a screen shot of the drivers in your pc Device Manager (when phone is connected to pc by usb, you hold volume up on phone when you plug it in).
There should be 'omap 4430' in 'other devices' in pc Device Manager. If correctly installed, it should NOT be flashing/blinking on and off. You must use the driver from the wkpark Fastboot package, not the one from the 'omap4flash installer' pack.
There are also two LG drivers that must be installed to pc. And there should be LG Cosmo device appearing in Device Manager someplace also, port set to 41.
I ask because driver install can be tricky or difficult, and confusing when you first do all of that. And, it is very important to have it all correct to flash successfully. Usually it is the problem when flash will not complete or start.
It also adds to difficulty that you must translate the instructions...
Click to expand...
Click to collapse
just lg cosmo driver doesnt work it never upgrade... and yeah i have windows 8 but i did the same on my other computer that has windows 7 and its the same problem
You must be logged on to pc as administrator. Use Windows 7, much easier. I have Win 7 x64.
Read all details carefully. Run everything as admin. ALL antivirus off. You must remove all old LG things from pc before beginning. Reboot pc. Install omap4flash. Restart pc. Install the two provided LG drivers. One of these you must force install. Restart pc.
Connect phone, vol. up to pc (no battery in phone, all of part 1). Link omap driver from Fastboot folder as described. Wait a bit for it to complete. When done here omap4430 will stop blinking.
Disconnect phone from pc. Connect it again, volume up, and LG drivers will install. Wait for it to process and finish. Change port to 41.
If LG drivers do not install when connecting phone the second time, try running omap4flash installer and UNinstall it. Reboot pc. Then try the above again.
Some things, like wkpark bootloader conflict with omap4flash (this is mentioned in the guide) so you may need to try it both ways.
Dude im desesperate
drastic00 said:
You must be logged on to pc as administrator. Use Windows 7, much easier. I have Win 7 x64.
Read all details carefully. Run everything as admin. ALL antivirus off. You must remove all old LG things from pc before beginning. Reboot pc. Install omap4flash. Restart pc. Install the two provided LG drivers. One of these you must force install. Restart pc.
Connect phone, vol. up to pc (no battery in phone, all of part 1). Link omap driver from Fastboot folder as described. Wait a bit for it to complete. When done here omap4430 will stop blinking.
Disconnect phone from pc. Connect it again, volume up, and LG drivers will install. Wait for it to process and finish. Change port to 41.
If LG drivers do not install when connecting phone the second time, try running omap4flash installer and UNinstall it. Reboot pc. Then try the above again.
Some things, like wkpark bootloader conflict with omap4flash (this is mentioned in the guide) so you may need to try it both ways.
Click to expand...
Click to collapse
i did all the steps and nothing works i have flashed a lot of roms and no matter what I get trapped in cwm I think i will send you the picture of my drivers and a video of me making all the steps of this guy
http://forum.xda-developers.com/showthread.php?t=1942836 because this http://forum.xda-developers.com/showthread.php?p=39130435 doesnt helped me a lot... If you have any other Idea of what is the real problem please tell me.
You can use xbsall's guide if you want, but the driver install process is the same.
Karim Kahale has an unbrick guide that uses Smartflash instead. You might find it easier, I do not know. It should be in O3D General section. Just do not "Erase Entire CP" or you will have to recover your IMEI.
Whatever you choose, I would stick with one method and see it through to completion. Trying too many things may just make the problem worse.
OMG!
drastic00 said:
You can use xbsall's guide if you want, but the driver install process is the same.
Karim Kahale has an unbrick guide that uses Smartflash instead. You might find it easier, I do not know. It should be in O3D General section. Just do not "Erase Entire CP" or you will have to recover your IMEI.
Whatever you choose, I would stick with one method and see it through to completion. Trying too many things may just make the problem worse.
Click to expand...
Click to collapse
Thank you so much i Fixed my cellphone !!
but now I have another problem, and is the reason why I did the factory reset is that I have ghost screen and someone told that if I do a factory reset I could solve it. oh and I cant use the camera.
Never had the screen issue so not sure. Camera should be working. Mine does. Use the button on touch screen to take a picture, I think 3D button has a bug in official ICS so it will not take a photo that way. Not sure, I always use touch screen button for that. Or maybe try rebooting phone a couple of times. It is possible I suppose that flash was incomplete or corrupt from incorrect driver install. If you are sure that is all good you might try redownloading the .bin file and flashing again. Beyond that, not sure. Maybe someone else knows???
I need help with my lg g stylo. I was using one click root Kingo root and when it was 66% done it was rebooting my phone into firmware download and my computer running Windows 10 froze to where I had to hard reset it, and my phone froze on firmware update. Now my phone is stuck in a bootloop on the LG life's good screen, I've tried hard resetting it ( with the volume down and power button combo) the Android guy pops up for one millisecond and disappears going back to the LG screen not doing anything the only other the only other thing I can do is go into downloading mode( while connected to a computer hold the volume button up) but when I do that my computer does not recognize my phone saying code 10 device cannot start up I have called LG they refused to help me get into recovery mode I have called Google Android support they don't know how to help I have also called windows trying to see if it was my computer's fault and they decided it wasn't I am kind of out of options I'm hoping someone knows how to help me I'll appreciate any help I can get thank you.
You need to download a MetroPCS KDZ and use rhe LG Flash Tool to flash the KDZ and bring your phone back to life.
I've tried that already I keep getting a Windows error code 10 device cannot power on I contacted windows and they said that is not my computer that is my device I have reinstalled my driver's serval times
Blairmathew071213 said:
I've tried that already I keep getting a Windows error code 10 device cannot power on I contacted windows and they said that is not my computer that is my device I have reinstalled my driver's serval times
Click to expand...
Click to collapse
To get into download mode you need make sure phone is 100% powered off then hold the volume up button and then plug in the usb cable. Dont release the power up button until the phone is fully in download mode not just the first screen. Also search for your phones adb drivers and install them to your pc not just the usb drivers. Make sure to uninstall any existing drivers first.
Thediesel1972 said:
To get into download mode you need make sure phone is 100% powered off then hold the volume up button and then plug in the usb cable. Dont release the power up button until the phone is fully in download mode not just the first screen. Also search for your phones adb drivers and install them to your pc not just the usb drivers. Make sure to uninstall any existing drivers first.
Click to expand...
Click to collapse
ok thank you i havent installed adb drivers yet ill let you know what happens
Blairmathew071213 said:
ok thank you i havent installed adb drivers yet ill let you know what happens
Click to expand...
Click to collapse
still not connecting to my pc uninstalled my usb drivers and reinstalled them and the adb drivers for my device my pc says " this device cannot start (code: 10)"
Blairmathew071213 said:
still not connecting to my pc uninstalled my usb drivers and reinstalled them and the adb drivers for my device my pc says " this device cannot start (code: 10)"
Click to expand...
Click to collapse
Did you try another pc with the adb drivers installed to see if you get the same error? If it connects on a different pc try this on the problem pc.
Open task manager
Click on the Hardware tab
Click the Device Manager button.
Expand Universal Serial Bus controllers section.
Right-click every device under the Universal Serial Bus controllers node, and then click Uninstall to remove them one at a time.
Restart the computer, and allow the computer to reinstall the USB controllers.
Plug in the your phone in download mode and test to to see if the issue is resolved.
You can also download Ccleaner and fix any registry errors for free. I've used it for years and it works really well.
Still no joy. Try a system restore on your pc sounds like the device management could be screwed up.
All kinds of funky sh*t can happens when a pc crashes. You said you have windows 10 as a last resort you can do a system refresh which reinstalls the os but keeps your files.
Thediesel1972 said:
Try a system restore on your pc sounds like the device management is screwed up. Also you can download Ccleaner and fix any registry errors for free. I've used it for years and it works really well. All kinds of funky sh*t can happen when a pc crashes. You said you have windows 10 as a last resort you can do a system refresh which reinstalls the os but keeps your files. Id try ccleaner first.
Did you try another pc to see if you get the same error?
Click to expand...
Click to collapse
yes ive plugged it into a pc running win 7 and i already did a pc reset i did the option to clean everything im thinking about formatting my hard drive and do a clean install of windows ill look into the ccleaner and see if that helps ill let you know what happens thank you
Blairmathew071213 said:
yes ive plugged it into a pc running win 7 and i already did a pc reset i did the option to clean everything im thinking about formatting my hard drive and do a clean install of windows ill look into the ccleaner and see if that helps ill let you know what happens thank you
Click to expand...
Click to collapse
Did you check my edited post?
Thediesel1972 said:
Did you check my edited post?
Click to expand...
Click to collapse
yes i did and still nothing but i think i found a way through android studio
Android SDK manager cannot find my device either I tried looking it up to my port and USB locator
Everything you need can be found here in the LG G Stylo forums and if it's not here a google search will help.
You need...
MetroPCS 5.1.1 KDZ
LG drivers
LG Flash Tool
Download the KDZ. Install the LG drivers while you wait for the 1.2GB KDZ to be downloaded. Download the LG Flash Tool and when the KDZ has completed downloading run it as an administrator. Settings in Flash Tool should be fine. Point to the KDZ and begin the flash. Normal or CSE. Normal does not wipe data, CSE wipes all user data. You'll be prompted with something about your internet connection. Do not close this, the tool should be flashing the KDZ. Wait for the phone to be rebooted after flashing. Profit.
Mattix724 said:
Everything you need can be found here in the LG G Stylo forums and if it's not here a google search will help.
You need...
MetroPCS 5.1.1 KDZ
LG drivers
LG Flash Tool
Download the KDZ. Install the LG drivers while you wait for the 1.2GB KDZ to be downloaded. Download the LG Flash Tool and when the KDZ has completed downloading run it as an administrator. Settings in Flash Tool should be fine. Point to the KDZ and begin the flash. Normal or CSE. Normal does not wipe data, CSE wipes all user data. You'll be prompted with something about your internet connection. Do not close this, the tool should be flashing the KDZ. Wait for the phone to be rebooted after flashing. Profit.
Click to expand...
Click to collapse
Thats not his problem its his pc read the prior posts
I had the same problem once the device connected as download mode.
The kdz tool doesn't detected and crashed all the times. But miracle happens I kept playing(open&close)the kdz tool app. Somehow it detected and flash the kdz.
Android Studio was a bust still unable to find my device even with the code to direct information to the only USB device connected
Shimster said:
I had the same problem once the device connected as download mode.
The kdz tool doesn't detected and crashed all the times. But miracle happens I kept playing(open&close)the kdz tool app. Somehow it detected and flash the kdz.
Click to expand...
Click to collapse
I'll try that and see if it works thank you
Did you ever try a different pc and if so was it detected by windows
Thediesel1972 said:
Did you ever try a different pc and if so was it detected by windows
Click to expand...
Click to collapse
Yes I've tried and computer running windows 7. Adb cannot find my device.
Blairmathew071213 said:
Yes I've tried and computer running windows 7. Adb cannot find my device.
Click to expand...
Click to collapse
I was under the impression that the phone was entering dl mode but just not getting recognized by the pc. Either or you should bring it to a corporate store and tell them it boot looped while updating and play dumb. They should replace it since its under warranty. Or call lg and do it that way although its about a ten day wait.
Thediesel1972 said:
I was under the impression that the phone was entering dl mode but just not getting recognized by the pc. Either or you should bring it to a corporate store and tell them it boot looped while updating and play dumb. They should replace it since its under warranty. Or call lg and do it that way although its about a ten day wait.
Click to expand...
Click to collapse
My phone does enter download mode just can't do anything from there. ADB can't find device. I even found the port I'm in and tried to force into recovery but still no device connected.