[Q] is the screen of the I9105 the same as I9100 is? - Samsung Galaxy S II Plus

Well the unfortunate happened and my lcd is dead. How do I know that the its just the lcd? the phone itself works beside the screen. I was suprized to see that the soft keys light up when I tried to see if it has any life left. had face lock on so I was able to get into it and hear the max volume bump noise. Tried to perform a blind call by pressing the screen in places that I think i should be able to make a call and whatdo you know? it calls! so I sat down to investigate more and i was able to get the adb running. problem was that with 4.2 you need to allow adb connection by clinking on a prompt on the thing it self to authorise it. so after a couple of minutes of just poking the screen I got adb running so I was able to screen cast it. :victory: couple minutes later I got Teamviewer working on it so I was able to controll it that way.
Anyway so much for that story. so I dropped it while walking a dog and it was in a leather case so atleast it landed somewhat softer. the screen does not seen to be cracked, the touch screen/digitizer still works, but no light can be seen from the screen.
I did took it apart cause I have no warranty. Sadly I'm no expert so I can't say whats wrong with the insides, but the lcd/digitizer connector looked to be sitting tight in its place. I did took the motherboard out and put it back after a quick look. Checked all the ribbon cables, everyting seemed to be sitting tight. So no luck there and I'm assuming that the lcd is just dead. Currently I have it in blind mode so it speaks out everyting I press
I was looking for some screen replacements and noticed that there is quite the difference between the I9100 and the I9105 screen prices. BUT the I9105 is basically I1900 with a different chipset? So I'm wondering if the screen form/chasi/cable placement is the same? if so than the prices are just obviously jacked up for the newer model.
P.S. writing this on a tablet and I type like a moron on this thing so sorry if your grammar nazi inside you flickers while reading this

Bump, seriously? noboby?

Related

In Panic Mode, help please--screen went dark

My screen worked fine earlier today, then out of the blue went dark. It is as if the backlight is set at a permanent low setting. I can barely make out what is on the screen. It is not totally black, but it is by no means easily visible. I have not made any reg changes or application installs that I did not previously have.
Please help. This particular device was an insurance swap out made in November. I have tried hard resetting, and nothing. It is still a very dark screen--even the initial TMo boot screen is dark.
I am running Jaguar 3.1 by NTS.
PLEASE...help. I would very much appreciate any insight. Is my screen fried? Is it able to be fixed?
Thanks in advance.
akashastrega said:
My screen worked fine earlier today, then out of the blue went dark. It is as if the backlight is set at a permanent low setting. I can barely make out what is on the screen. It is not totally black, but it is by no means easily visible. I have not made any reg changes or application installs that I did not previously have.
Please help. This particular device was an insurance swap out made in November. I have tried hard resetting, and nothing. It is still a very dark screen--even the initial TMo boot screen is dark.
I am running Jaguar 3.1 by NTS.
PLEASE...help. I would very much appreciate any insight. Is my screen fried? Is it able to be fixed?
Thanks in advance.
Click to expand...
Click to collapse
you can try the prog Mymobiler to see if your today screen is really dark (if it´s dark on your computer too, than i think it´s a software failure) if it´s shown normal on your computer than i don´t know, maybe hardware failure...
sorry can´t help more
steph
I have that program too, and didn't even think about that. I will try it and report back. Thanks for the idea.
EDIT
Everything works fine using My Mobiler. I was able to make sure power and brightness adjustments were made-but to no avail. I even flashed a different rom just to rule out rom failure. My screen is still dark. In bright light I can barely view the item, and that is with some serious squinting.
Could it be my screen needs replacing, or is this a bigger issue like the mobo? If you suspect the screen only, could you please suggest where I can get a replacement screen?
This sucks big time. I love my Wizard and really do not want to move to an inferior device (like a "regular" cellphone, or the Wing--which is what insurance would swap me with).
PLEASE HELP ME FIX MY WIZ!!
I remember a long time ago...
akashastrega said:
I have that program too, and didn't even think about that. I will try it and report back. Thanks for the idea.
EDIT
Everything works fine using My Mobiler. I was able to make sure power and brightness adjustments were made-but to no avail. I even flashed a different rom just to rule out rom failure. My screen is still dark. In bright light I can barely view the item, and that is with some serious squinting.
Could it be my screen needs replacing, or is this a bigger issue like the mobo? If you suspect the screen only, could you please suggest where I can get a replacement screen?
This sucks big time. I love my Wizard and really do not want to move to an inferior device (like a "regular" cellphone, or the Wing--which is what insurance would swap me with).
PLEASE HELP ME FIX MY WIZ!!
Click to expand...
Click to collapse
The first time I have use a Pocket pc in settings I uncheck the square that say "Turn on backlight whena button i pressed or the screen is tapped".. or something, jeje every time I turned on my wizard, it hasn't light jaja.
But I think that your problem is hardware, you need another wizard to change displays... cause if you buy a new display... maybe the failure isfor the motherboard...
Think about it...
+ Que PPC said:
The first time I have use a Pocket pc in settings I uncheck the square that say "Turn on backlight whena button i pressed or the screen is tapped".. or something, jeje every time I turned on my wizard, it hasn't light jaja.
But I think that your problem is hardware, you need another wizard to change displays... cause if you buy a new display... maybe the failure isfor the motherboard...
Think about it...
Click to expand...
Click to collapse
Thanks for your quick responses!!
I was worried that the issue could go beyond just screen issues. Does anyone know a way to troubleshoot something like this? To find out if it is just a screen, or if the MoBo is going out on me...
**Or is anyone willing to sell me their working but no longer used wizard? I can afford about $100 (+shipping costs/insurance) for a used but working device. My hubby is unemployed and I am on disability so right now money is tight.
akashastrega said:
Thanks for your quick responses!!
I was worried that the issue could go beyond just screen issues. Does anyone know a way to troubleshoot something like this? To find out if it is just a screen, or if the MoBo is going out on me...
**Or is anyone willing to sell me their working but no longer used wizard? I can afford about $100 (+shipping costs/insurance) for a used but working device. My hubby is unemployed and I am on disability so right now money is tight.
Click to expand...
Click to collapse
Check ebay, you maybe able to find a working phone for 100 bucks. Gook luck!
have you checked the wiring (flat cable) that connects to the screen.
maybe you just need to replace that. if the screen works, then it is just the LED's that are not responding. maybe just a loose connection, or a broken contact.
Does the keyboard light up?
i think i have the same problem or at least similar.
my screen backlight goes black from time to time when i press the screen "too hard", but that comes and goes.
interesting: i'm using homescreen plusplus (ex-batterystatus) to overclock my cpu with the option "set cpu speed at wakeup" activated. when i turn off my screen with the power button and then turn it on again, in most cases my backlight turns on, too.
but that's to enerving for me to live with that, so i disassembled my wizard and found some sort of black dot on the flat display connector. maybe it has something do with that? and if so, where can i get such a flex cable?
S.V.I said:
have you checked the wiring (flat cable) that connects to the screen.
maybe you just need to replace that. if the screen works, then it is just the LED's that are not responding. maybe just a loose connection, or a broken contact.
Does the keyboard light up?
Click to expand...
Click to collapse
I have the manual--I used it when my usb was fubar'd--but I am a bit intimidated about doing something with my screen. Is it something that can be easily screwed up if I even look at it funny, or can I handle it carefully and not worry that the mere act of touching it will make it explode??!!
Perhaps I am being a bit dramatic, but you get the idea I think.
Do I have to be totally grounded out first? Do I need gloves on? Or do I just rip the dang thing apart and go at it?
Thanks for your help and responses.
akashastrega said:
I have the manual--I used it when my usb was fubar'd--but I am a bit intimidated about doing something with my screen. Is it something that can be easily screwed up if I even look at it funny, or can I handle it carefully and not worry that the mere act of touching it will make it explode??!!
Perhaps I am being a bit dramatic, but you get the idea I think.
Do I have to be totally grounded out first? Do I need gloves on? Or do I just rip the dang thing apart and go at it?
Thanks for your help and responses.
Click to expand...
Click to collapse
You can get an anti-static kit in Radioshack!
Well I don't have a Wizard, so this might not be much help; however, I have had a similar problem with my Touch Elf after installing a new app. The dark screen did not appear until I performed a soft reset and I really started to panic because there was nothing I could do to change it. I could barely make anything out that was being displayed it was so dark. Even when I turn my screen brightness down it was not ever that dark. Just out of luck though I pluged my phone into my computer VIA USB and voila, the backlight came on. I could use my phone again and immediately navigated to my brightness display settings and turned it all the way up (it was set all the way down for some reason). I have not had this problem ever since. I don't know if you have tried this already or not - It was not mentioned in any posts.
Good luck
Rod
Check out eBay for a replacement LCD, I got one last week for € 32,- ($45,-) including the shipping costs.
BUT...when buying from eBay notice the following 2 things:
1) The screens are most of the times used screens with a new (hand-soldered) digitizer on it (but it is done nicely as far as I have seen).
2) Disassemble your Wizard, check if your LCD has a BLACK or a GOLDEN flex ribbon cable at the back.....when you purchase the wrong one, it will not work!
An alternative is just to buy a 2nd hand Wizard for like $70 / $80, buy a new housing for it ($40) and it looks brand new (except for the LCD, most LCD's do have some scratches on it).
A HTC Wizard Service Manual can be found in the Wizard section on the XDA Dev FTP Server (I use it a lot), sometimes when buying a LCD on eBay they will also send you the tools needed to disassemble and reassemble the Wizard.
Good luck!
jozzy said:
i think i have the same problem or at least similar.
my screen backlight goes black from time to time when i press the screen "too hard", but that comes and goes.
interesting: i'm using homescreen plusplus (ex-batterystatus) to overclock my cpu with the option "set cpu speed at wakeup" activated. when i turn off my screen with the power button and then turn it on again, in most cases my backlight turns on, too.
but that's to enerving for me to live with that, so i disassembled my wizard and found some sort of black dot on the flat display connector. maybe it has something do with that? and if so, where can i get such a flex cable?
Click to expand...
Click to collapse
I can furnish you with a flex cable for $15.00, plus $5.00 for shipping. Let me know if you have an MDA or 8125.

Att Fuze black screen need help please! Not a bad flash issue.

Hi all,
I am at my wits end on this problem if anyone can offer any adivice it would be greatly appreciated. So let me give a recap of what has occured thus far. The water damage tag for some reason turn pink thus i am unable to get warranty exchange. I am pretty certain that the phone has never been expose to any water of anything of that sort, but i do live in houston, tx so might be humidity or what not that cause the tag to turn. Anyways.
1. This all started after i flashed RRE 5.2 RC3. Initially after a successful flash everything seem normal and fine. Then next morning i woke up to a frozen screen with many verticial lines running up and down the screen was almost unreadable. Initially i thought it was a bad flash or just random lock up. I did a hard reset and tried to enter the bootloader. Black screen, it does seem like the backlight is coming up but nothing on the screen. I can hear the phone power on and boot successfully into windows. Activesync connects i can browse the contents of the phone.
2. After flashing to stock att rom and stock htc roms same symptoms. So at this point i am thinking crap bad LCD screen. so I ordered both the digitizer and lcd screen for good measure. I replaced them hoping that a bad LCD was all. replaced both screens and i powered on the phone. same problem. black screen. The phone still powers on and boots into windows. Activesync still connects and i cna still reflash the phone.
3. I work extensively and do both desktop pc and notebook repair. I am not new to dealing with small electronic repairs. but at this juncture i am unable to identify the cause of hte malfunction. i am hoping maybe some of the gurus here might be able to shine some light on the subject.
Thanks in advance for any help.
I would have followed the same approach; your description makes it sound like it might be some kind of backlighting issue at first read. I'm inclined to think it might be a cold connection (bad connector) on the main board.
Silly question, what happens if you power up the phone with the keyboard exposed?
*EDIT* Not sure if you have been here yet: http://www.mikechannon.net/
Cheers,
i just tried to power up the phone with keyboard exposed. Powers up the same as with the keyboard hidden. Still boots up fine but black screen. I already have the service manuel dowloaded. i have checked around with several repair places both local and on the web. Seems like no one has any parts for the att fuze/touch pro gsm except for the lcd and digitizer and a speaker.
its quite possible that it is a main board but as the same time it might be something as simple as a ribbon cable. i have contacted htc about doing a possible repair and they want wayyyy too much for just a main board repair almost $400 USD.
Anyone have a bricked/ non working touch pro they would like to sell ? =P
fkoong said:
its quite possible that it is a main board but as the same time it might be something as simple as a ribbon cable.
Click to expand...
Click to collapse
Could be a bad ribbon cable ... and firmly pressing around the front/back of the unit shows no change?
pressing the phone front and back show no changes to display. in a very dark room I can see that there is light emitting from the display but its just the screen is not displaying anything visable. this occured both before and after i changed out the screens. I'll do another visual inspection of all the boards to see if there is any bad resistors burnt out circuits etc.. but i didn't notice anything mentionable during my first 2 inspections. Maybe 3rd time is the charm.
Thanks for all the feedback thus far Hilaireg it is quite appreciated. All this venting has at least made me feel 1000% better than after i replaced my lcd and still same problem at least i don't feel like a complete idiot!
Sorry I couldn't be of much help ... you've done all the steps a seasoned hardware person would do.
Do post back to let other folks know if you get it back up and running.
Cheers,
you have a pm fkoong.
I have possibly the same problem. Phone got wet, dried it out for 2 days (in a container of rice). Phone worked but had "water marks" on screen that disappeared after two days and everything was fine for about 2 weeks. Then one day (happened to be humid misting rain eve in Charleston) the screen is blank (hint of backlight only). A soft reset and it seems OK for about 1hr, then blank again. The hard resest screen displayed OK (readbale text etc), but didnt work. But as I write this, I retry to document it results correctly and the NATF ROM is reloading and the screen works! We will see how long!!
Well.. not that long, the end of the ROM load and it went blank again, seems like a video driver problem. The Press VoluP to boot does show some red artifact.
Trying hard reset again (No SIM no uSD)
The NATF v4.4 loads and gives me the Tap screen, Align Screen, stylus, loads customization, opera, tf3d, then loads a bunch of files under ...... and then the screen goes blank again, seem like what happened last time, so Ill try loading a fresh ROM copy... later

Black screen. Cant see anything but phone still works

So today my phone fell into some garbage. I dont think there was any water, but after doing some googling, it seems that is one of the causes. After i pulled the battery out, the little circle is pure white but i do see a very little spot of red. Can anyone give me any tips? If its ruined, can i easily replace it? I just got this from ausurion a few months back. I dont really want to have to shed out another 200 for another phone. I put it in rice for the time being just in case.
I can turn it on, and it vibrates normally, and it vibrates when things happen. The bottom icon lights also turn on. So, just imagine your phone working, you just cant see anything.
EDIT: Also, i cant get into fastboot, recovery, etc because it is only blank. Should i be looking into a new screen?
If there's water damage, it might be a lost cause, but if it's not, replacing the screen would be a much cheaper option than shelling out $200.
It isn't anything to do with water my phone did the same thing. You damaged the wires going to the screen. Touch still works right. Do you have insurence?
Zinsko said:
It isn't anything to do with water my phone did the same thing. You damaged the wires going to the screen. Touch still works right. Do you have insurence?
Click to expand...
Click to collapse
There are many different causes of problems. You can't be positive that it isn't a certain cause.

[Q] White screen of death?

Has anyone encountered the following issues with their SHIELD?
Mine was working just fine after updating to 4.3 and rooting with CWM. I performed multiple reboots in this configuration, played games, etc. - everything was fine.
I had a pretty busy weekend so didn't touch the SHIELD at all for a few days. When I got back:
When I opened it up, I saw the screen backlight turn on but nothing displayed on the screen. The SHIELD button was glowing green.
I long-pressed the SHIELD button to turn off the device. When I turn it back on, I get a white screen that is dark around the edges (mostly vignetting around the corners). The brightness of the screen here and degree of vignetting seem to change every time I try and turn on the device.
If I enter fastboot mode via the key combo, the same thing happens - white vignetted screen. The device DOES appear to enumerate as a fastboot device on my PC in this configuration.
At one point I figured it might be due to a low battery, so plugged it into the charger. 30 minutes later, when I opened the lid, I actually came up to a launcher screen with 65% battery.
However, after closing the lid and reopening it again - black screen again, with the "white vignette of death" coming back if I reboot.
Has anyone else seen similar behavior? Searching results in no one complaining about a white screen like this, at least not on this device.
Screen of Death
This just happened to me today. Did you find a fix for this problem?
Entropy512 said:
Has anyone encountered the following issues with their SHIELD?
Mine was working just fine after updating to 4.3 and rooting with CWM. I performed multiple reboots in this configuration, played games, etc. - everything was fine.
I had a pretty busy weekend so didn't touch the SHIELD at all for a few days. When I got back:
When I opened it up, I saw the screen backlight turn on but nothing displayed on the screen. The SHIELD button was glowing green.
I long-pressed the SHIELD button to turn off the device. When I turn it back on, I get a white screen that is dark around the edges (mostly vignetting around the corners). The brightness of the screen here and degree of vignetting seem to change every time I try and turn on the device.
If I enter fastboot mode via the key combo, the same thing happens - white vignetted screen. The device DOES appear to enumerate as a fastboot device on my PC in this configuration.
At one point I figured it might be due to a low battery, so plugged it into the charger. 30 minutes later, when I opened the lid, I actually came up to a launcher screen with 65% battery.
However, after closing the lid and reopening it again - black screen again, with the "white vignette of death" coming back if I reboot.
Has anyone else seen similar behavior? Searching results in no one complaining about a white screen like this, at least not on this device.
Click to expand...
Click to collapse
Might be just bad luck for me.....
nmerc001 said:
This just happened to me today. Did you find a fix for this problem?
Click to expand...
Click to collapse
So ive already gotten two shields and they both got the same effect. my guess is the ribbon cable when you open and close the screen, is wearing off? because when i open my shield in a certain way, it works... when i open it at around 100 degrees or open correctly then tilt it forward, the screen tears and slowly shows the white screen. I do admit that i open and close the screen more than i should, but i do it carefully. Ill look over at the ifixit site to see how the cable is connected to the board.
This is what has me worried about buying a shield, the ribbon cable, did you confirmed this was the problem?
DJNinja1625 said:
So ive already gotten two shields and they both got the same effect. my guess is the ribbon cable when you open and close the screen, is wearing off? because when i open my shield in a certain way, it works... when i open it at around 100 degrees or open correctly then tilt it forward, the screen tears and slowly shows the white screen. I do admit that i open and close the screen more than i should, but i do it carefully. Ill look over at the ifixit site to see how the cable is connected to the board.
Click to expand...
Click to collapse
I am a tech by trade and bought one of ebay for 40 bucks cuz it would not power up so the guy claimed. After getting it I found the issue was actually the display was not coming on and once it did. Then went out in a few moments. Connect it to HDMI and the unit runs all day of you want to be cabled. ]
So I tore it down and found that the issue is the flex cable. The problem is that the flex cable is part of the LCD and you cannot just replace the cable. Also since the unit is so new there are no sources as of yet to by the LCD from.
So if you have this issue I suggest just holding out till a source of LCD's at hopefully a reasonable price become available.
So it's soldered to the screen and not replacable right?
nex86 said:
So it's soldered to the screen and not replacable right?
Click to expand...
Click to collapse
That is correct.. The flex cable is actually an integral part of the display and even has much of the driver circuitry placed right on it at the LCD. In the business we call it a flex circuit since it is a flexible circuit board and not just a cable.
I pretty much know what you mean.
On my old Archos Gamepad I ripped the flex that connected the left side of the controler to the logic board by accident.
It was a pain in the ass to fix it by soldering seperate wires, I guess it's impossible to do this with the display connection in the Shield.
nex86 said:
I pretty much know what you mean.
On my old Archos Gamepad I ripped the flex that connected the left side of the controler to the logic board by accident.
It was a pain in the ass to fix it by soldering seperate wires, I guess it's impossible to do this with the display connection in the Shield.
Click to expand...
Click to collapse
Might be possible if you used 32 gauge magnet wire. It is enamel coated so it won't short, but it to will break over time.
hi, flash factory image
Sent from my LT25i using XDA Free mobile app
dragxdk said:
hi, flash factory image
Sent from my LT25i using XDA Free mobile app
Click to expand...
Click to collapse
How are you supposed to flash a factory image when the screen won't let you see what you are doing? When you are in the bootloader screen the HDMI drivers are not loaded yet so not even hooking it to an external monitor will work. You might want to fully read and understand the problem next time before offering advice.:good:
fastboot tells you if you were sucessful or not.
just for relocking the bootloader you have to do some button combinations, you can look up some tutorial videos to see what you have to press.
nex86 said:
fastboot tells you if you were sucessful or not.
just for relocking the bootloader you have to do some button combinations, you can look up some tutorial videos to see what you have to press.
Click to expand...
Click to collapse
Even still, it is not a software problem that causes this. I know because if I move my display to a certain angle it will start to work sometimes. A software issue would not cause this. I also have taken my apart since I am a tech and can actually see the traces in the flex cable that have broken..
Any device with a folding display is a bad idea and a failure waiting to happen. Flex cables have a limited number of flex cycles that is even usually published. So the idea of using them in a device that may get heavy use is just dumb.
Solarenemy68 said:
Any device with a folding display is a bad idea and a failure waiting to happen. Flex cables have a limited number of flex cycles that is even usually published. So the idea of using them in a device that may get heavy use is just dumb.
Click to expand...
Click to collapse
I agree, they used flex in the Nintendo DS and 3Ds as well, but they don't break that fast.
I find it still better if they have used recular cables like what they use for Laptops.
Solarenemy68 said:
Even still, it is not a software problem that causes this. I know because if I move my display to a certain angle it will start to work sometimes. A software issue would not cause this. I also have taken my apart since I am a tech and can actually see the traces in the flex cable that have broken..
Any device with a folding display is a bad idea and a failure waiting to happen. Flex cables have a limited number of flex cycles that is even usually published. So the idea of using them in a device that may get heavy use is just dumb.
Click to expand...
Click to collapse
What you are saying is the EXACT same thing that happened to my SHIELD. I can tell its a hardware problem because when I tilted my screen it would work, and sometimes it wouldn't. Now my SHIELD's display does not even show any signs of picture. HDMI still works, however. Like one of the previous posts said, there is not a screen available for purchase, so my next step is NVIDIA customer support. Maybe if they would sell these screens, I wouldn't even have to have a warranty claim. sigh.
White screen of death?
yes mine too same as
i tried connecting my via HDMI from power cable to large HDMI to plug it works fine on my galaxy tab
thought id be clever try it on nvidia shield never worked sould of bought mini HDMI so now White screen of death
i cant get into recovery or anything i had this on charge for 12 hrs yesterday still no green button on charge only orange .. i too cant find anything on internet to help with this White screen of death situation
Solarenemy68 said:
How are you supposed to flash a factory image when the screen won't let you see what you are doing? When you are in the bootloader screen the HDMI drivers are not loaded yet so not even hooking it to an external monitor will work. You might want to fully read and understand the problem next time before offering advice.:good:
Click to expand...
Click to collapse
This. I'm having a similar issue. My wife's SHIELD has an unresponsive touch screen. So I tried to flash the factory image (It was never rooted to begin with) and I got the white screen issue when in the bootloader screen. I have to keep restarting it to get the screen to show up as normal when the device boots to the home screen. But the bootloader screen is still blank and white. I was able to watch a video and mimick the steps to flash the factory image but that did not fix the issue. It's definitely a hardware issue. I live in Cincinnati OH, anywhere I can go to have this fixed? I have a portable myself and i know this is going to happen to mine soon.

[Q] I Screwed Something Up

A friend of mine had a Galaxy S3 Amber with a broken (and blank) screen and wanted her data from it's internal memory that is locked and not in debugged mode. I did a lot of research and found the best, most efficient way was to do a motherboard swap with another gs3. I had a Galaxy S3 Blue. I watched a couple of videos and it seemed rather easy. I gathered the proper tools and was EXTREMELY careful not to break or rip anything (and to my knowledge i did not). When i put her motherboard from the amber one into the blue one and the screen would not come on. My first thoughts were it must be her motherboard that went bad. Well when i went to put my blue gs3 back together (again being very careful this entire time) I'm now having the same issue as she was. Black screen, no back light. The bottom lights DO come on and i feel it vibrate when i get a message. There was also no power on chime...
I know its hard to tell with out looking but any ideas on what could be wrong or what i might have screwed up? i checked all the connections and everything looks perfect. Nothing is bent or connected wrong and I didn't force or break anything.
update: so i found that the touch part of it still works fine. i can hear the ripple unlock as well as all the other sounds and such when i touch around and i can here it opening apps. the only issue lies in the screen itself being blank with no back light what so ever,
First of all remove the battery and attempt to power on, then leave without battery for 1 min, I know this sounds silly but it worked on an old iPhone 3G so anythings worth a shot.
If that doesn't work go back into the S3 and make sure all the data clips are firmly in place and locked down but not twisted in anyway. Also make sure their is no moisture or dust on the ribbons. You may not realise it but even the smallest imperfection with this can cause massive issues down the line.
If all else fails her phone may have broke your screen, I don't know how but it is a possibility
Hope I could help and good luck
TechMinerUK said:
First of all remove the battery and attempt to power on, then leave without battery for 1 min, I know this sounds silly but it worked on an old iPhone 3G so anythings worth a shot.
If that doesn't work go back into the S3 and make sure all the data clips are firmly in place and locked down but not twisted in anyway. Also make sure their is no moisture or dust on the ribbons. You may not realise it but even the smallest imperfection with this can cause massive issues down the line.
If all else fails her phone may have broke your screen, I don't know how but it is a possibility
Hope I could help and good luck
Click to expand...
Click to collapse
so i took it apart again today to double check and clean everything and under inspection i noticed a teeny tiny slit on the edge of the lower, bigger ribbon. i know the smallest bit could be horrid. Any fix and would that cause just the screen to not show? i don't know if that is the led connection but i think it may be.
amshook said:
so i took it apart again today to double check and clean everything and under inspection i noticed a teeny tiny slit on the edge of the lower, bigger ribbon. i know the smallest bit could be horrid. Any fix and would that cause just the screen to not show? i don't know if that is the led connection but i think it may be.
Click to expand...
Click to collapse
If theirs a slit I'm affraid that could be it for the screen, like I said even the smallest imperfection can cause massive issues. The slit is probably in the one of the data sections of the ribbon cable which is why data for the screen isn't being carried.
For the fix I don't think their is one unless you can fit a new ribbon on to yout S3's screen
Sorry about the screen
So I took it all apart again. Cleaned ever little thing I could and now it works again. ?
amshook said:
So I took it all apart again. Cleaned ever little thing I could and now it works again. ?
Click to expand...
Click to collapse
Excellent, must have just had some dust or gunk on the cable
Glad you got it working again:victory:
TechMinerUK said:
Excellent, must have just had some dust or gunk on the cable
Glad you got it working again:victory:
Click to expand...
Click to collapse
As am I. Thanks alot for helping. I appreciate it. id buy you a beer if I could lol.
amshook said:
As am I. Thanks alot for helping. I appreciate it. id buy you a beer if I could lol.
Click to expand...
Click to collapse
No problem, thats what XDA is here for:laugh:

Categories

Resources