Related
While a lot has been written, the following should provide an easy-to-follow guide:
Preparation:
1. A torch (read on and you will know why)
2. 256M SD card
3. Download ntrw.exe, romupdate.exe, hexedfull.exe from the ftp of this forum to c:\ and install hex editor
4. Download the appropriate ROM file (hereafter referred to as "newrom.nb1").
5. Cancel USB in ActiveSync
6. Use Sprite Backup to backup your ppc
Backup original ROM:
1. Put pocket pc into the boot loader mode (hold both on/off and camera buttons at the same time while resetting).
2. Insert empty SD card.
3. Connect pocket pc to pc through USB.
4. Run romupdate.exe on pc.
5. Select “\\.\WCEUSBSH001” in port settings. In the popup windows, enter “d2s” and press enter.
6. Don’t get panic to see the pocket pc screen goes dark. Use your torch and you will see the download percentage. Wait until it reaches 100% and shows “CheckSum is OK!”.
7. Insert SD card into card reader of the pc. Ignore the “format SD card” message and click “No”.
8. Run “command” to go into DOS prompt and change to root directory (cd c:\). Enter “ntrw read oldrom.nb1 s:” where s is the drive of your SD card.
9. Ignore the “Data error <cyclic redundancy check>” message. You should save another copy of this important rom file “oldrom.nb1”.
Change header of newrom.nb1:
1. Right click on oldrom.nb1 to open hex editor. Copy the first 416 bytes.
2. Open the downloaded newrom.nb1 file and overwrite the first 416 bytes with those of the old rom.
3. Save the edited newrom.nb1. You may save another copy of this important file.
4. Go to the command prompt and enter “ntrw write newrom.nb1 s:” to write it to the SD card. Ignore the error message “The parameter is incorrect”.
Update the ROM:
1. Insert SD card into pocket pc and put it to boot loader mode again (on/off + camera + reset). Use you torch to check the dark screen.
2. When it shows “Press Power to flash”, press the on/off button. Wait until it reaches 100% and ignore the message “Download Fail - CheckSum Fail”
3. Soft reset your pocket pc.
4. You may have to reinstall your software, unless you are familiar with the advanced features of Sprite Backup.
Ask you a question.
Does it backup 3 parts of rom (OS rom, extended rom and Radio rom)?
I am trying to backup my old Qtek Rom so I can install an update. I follow the steps to perfection..
The file created by ntrw is 999Mb big and at the end of the file I get an error stating that "parameters are incorrect"
Does this mean that the backup was not done successfully?
Why is the file so large?
Thanks for your help
ntrw get image SD card. Use SD card 256 Mb.
SD Card update problem
Hi I used ntrw.exe to backup my original rom to an SD card. It all went ok and I was able to clear the SD, write the rom back on the SD and put it in my M500. Normally I got a menu to press the power button to flash the rom to my phone, but now whatever I do I can't get the menu back. I won't get the option "Press power button" to flash. What I also see is that somethimes when I put the SD back in my laptop it is totaly empty. Normaly it would ask me if I want to format the SD because it can't be read. Can anybody help??
Thanks!
Dear All,
this is my first time to this site.
Could you please send me the download links for the files that are necessary (or the files themeselves) to backup the ROM (ntrw.exe, romupdate.exe, hexedfull.exe )
Thanks a million.
Will
i found this http://www.ccoo.net/MDAFlash/ntrw.exe
Thank you for this wonderful guide !!!
I am trying to backup my I-Mate JAM's ROM with a 256 MB SD card. However I have a similiar problem where when the ntrw.exe completed with the same "parameters are incorrect" error. The created ROM image is about 247,040 KB.
Is this correct? I did make sure the SD card is empty before the backup process (by deleteing everyfile on it), or should I use some proper method to ensure the SD card is actually completely empty?
Thanks in advance for any help!
Mine came up with that every time, but worked ok. I am trying to do the Anasky ROM update to my magician, and the backup i made of the original rom was fine to restore, even though i got that error.
mitchello said:
Mine came up with that every time, but worked ok. I am trying to do the Anasky ROM update to my magician, and the backup i made of the original rom was fine to restore, even though i got that error.
Click to expand...
Click to collapse
Thanks a lot for this info! It certainly make me feel a lot more confident about what I am doing
Thanks again !
Jyhnc said:
Thank you for this wonderful guide !!!
I am trying to backup my I-Mate JAM's ROM with a 256 MB SD card. However I have a similiar problem where when the ntrw.exe completed with the same "parameters are incorrect" error. The created ROM image is about 247,040 KB.
Is this correct? I did make sure the SD card is empty before the backup process (by deleteing everyfile on it), or should I use some proper method to ensure the SD card is actually completely empty?
Thanks in advance for any help!
Click to expand...
Click to collapse
someone in this forum told us that the rom size is vary and closed to the size of your sd card.
I used 128mb to backup and restore, it worked fine.
Has anyone experienced the problem of trying to reflash the device with the SD and when placed in Bootldr, the display just says serial and never progresses to press power to flash??
thanks
Jim
turn off the USB connection in your activesync, it will interfere the upgrade.
Found the fault, I reconnected the USB whilst entering the bootldr with the SD in socket and worked fine... Quite strange though as I couldnt remember having the USB connected the lasst time I performed the process
rgds
jim
jfran said:
Found the fault, I reconnected the USB whilst entering the bootldr with the SD in socket and worked fine... Quite strange though as I couldnt remember having the USB connected the lasst time I performed the process
rgds
jim
Click to expand...
Click to collapse
Hi All,
I was stuck at the Serial for a Looooooong time. Nothing worked. Until I did the following:
1) Using HHDHexeditor, copy the first 416byte (NOT 220byte!)
2) Write the copied original backup ROM into the new ROM (.nb1 file)
3) Put into your 02 Mini
4) VERY IMPORTANT! - Plug into your USB PORT!
5) Then I see the "Press Power button to Flash!"
and I am happily flashing my device now ... My guess is that it needs to be on external power in order to upgrade .... Thanks everyone .. can't wait to see my new baby with 27Mb storage! :twisted:
I'm using 256Mb SD Card ....
Alvin
How can i know the backup file name stored in the memory card? (*.nb1)
Thx~~
i am not seeing the popup window in which to select "d2s"...can anyone help?
update: Ok, so i was just temporarily blind! Have managed to continue and have fingers crossed it is ok.
2. When it shows “Press Power to flash”, press the on/off button. Wait until it reaches 100% and ignore the message “Download Fail - CheckSum Fail”
3. Soft reset your ppc.
After this.... how I do the soft reset with my ppc?? Connect or diconnect with the USB?? Coz I can't turn it back to the normal from boot loader mode even I do soft or hard reset after the rom flashing.......why?? :shock:
cojones said:
update: Have managed to continue and have fingers crossed it is ok.
Click to expand...
Click to collapse
I get the message ROM size isn't enough when i press the power button to flash from the sd card...why is this?
Talents said:
5. Select “\\.\WCEUSBSH001” in port settings. In the popup windows, enter “d2s” and press enter.
Click to expand...
Click to collapse
WTF ??? The only options are COM1 COM2 or COM3 and the Baud rate.
What a POS!
hi
im trying to root my samsung galaxy 7 plus
i have followed all of the steps,
Im stuck at recovery mode, after copying root.zip to sd card, run in recovery mode,
I get this error when trying to run uodate from external card/storage
"E:failed to mount sdcard (no such file or directory)"
Yeah i heard that i need to install and new partition and overwright sd data, turns out i need to be rooted to be able to do that
How can i do this without rooting?
If anyone has a salution to my probleme please pm me and post in this forum
christiaan47 said:
hi
im trying to root my samsung galaxy 7 plus
i have followed all of the steps,
Im stuck at recovery mode, after copying root.zip to sd card, run in recovery mode,
I get this error when trying to run uodate from external card/storage
"E:failed to mount sdcard (no such file or directory)"
Yeah i heard that i need to install and new partition and overwright sd data, turns out i need to be rooted to be able to do that
How can i do this without rooting?
If anyone has a salution to my probleme please pm me and post in this forum
Click to expand...
Click to collapse
You should use the CWM 6.0.1.0 version. Also, the best idea is to use a secondary SD card, not the internal storage. You will notice that in the recovery, the option names are wrong. The one that says "external" is actually your internal storage.
hi
robyr said:
You should use the CWM 6.0.1.0 version. Also, the best idea is to use a secondary SD card, not the internal storage. You will notice that in the recovery, the option names are wrong. The one that says "external" is actually your internal storage.
Click to expand...
Click to collapse
Oh okay thanks, but i only have a option for external, btw can i charge my phone in recovery mode
You need to copy it to the external card if you're staying stock, either in /extstorages or /emmc, depending on hc or ics. Sdcard is your internal partition
Sent from my myTouch 4g via Tapatalk
re
ringnutz said:
You need to copy it to the external card if you're staying stock, either in /extstorages or /emmc, depending on hc or ics. Sdcard is your internal partition
Sent from my myTouch 4g via Tapatalk
Click to expand...
Click to collapse
Yes i copied to root/extstorages, the problem is it still doesnt pick up my sdcard
re
im goning to try and use the SuperOneClick app
Wtf? Here r tutorials everywhere....
Use mobile odin(rename to recovery.img) or heimdall to flash cwm 6.0.1.0 from aorth. Then use cwm to get root.
Sent from my GT-P6200 using xda app-developers app
Rooting Galaxy Tab 7.0 Plus GT-P6200
Here is what worked for me. I got a lot of help from a lot of people on this site, so I want to share the knowledge.
I downloaded two files (which are attached to this post).
Put both files on your EXTERNAL SD CARD. If you don't have one, get one.
Boot into recovery mode. To do this, shut off your tablet and then press the power and volume up button at the same time. When you see the Samsung logo, let go of the power button only. When you see the next graphic with the android you can let go of the volume button. You should be in recovery mode now.
Use your volume up/down button to highlight 'apply update from external storage' Press power to select
Use your volume up/down button to highlight cwm.zip and press the power button to select it
** When cwm appears DO NOT use the volume +/- buttons anymore. Instead use the touch screen to do the rest of the procedure
In CWM use your finger to choose 'install zip from sd card'
Now, (not sure why) use your finger to tap 'choose zip from internal sd card'
Use your finger to scroll down until you see the root.zip file that you copied to your sd card and tap it
From here, you're good to go. I have no idea why I had to choose the option to choose zip from INTERNAL sd card, especially since I didn't do so. But, regardless, this worked for me. I installed Superuser and Titanium Backup without a problem.
I hope this helps you. I am by no means an expert at anything Android, but this site did go a long way with helping me out. I hope I was able to do the same for others.
One thing I did not understand is why, when I was asking for help with rooting my tablet, people suggested I use Mobile Odin. Mobile Odin requires the tablet be rooted to use it, so using Mobile Odin to root isn't possible unless I am misunderstanding something.
Edit: Now I am embarrassed. I just found this, after the fact.
You're almost there!
christiaan47 said:
Oh okay thanks, but i only have a option for external, btw can i charge my phone in recovery mode
Click to expand...
Click to collapse
I got confused with that too, but I succeeded:
Sorry, Christiaan, but YES, there on the bottom you will find INTERNAL CARD too.
When you choose INTERNAL CARD, in fact it uses you SD CARD.
After choosing INTERNAL CARD, you will see your SD CARD folders. Then you will be able to root it!
go ahead, man!
hi all,
i have no problem in following the guide.... its very simple.
BUT still i get the message (( E:failed to mount sdcard (no such file or directory) ))
i did copy the 2 files "root" & "CWM"..... this is how i did copy them, correct me if am wrong please
1- plug my PG-6200 with Usb to PC
2- the auto window open showing 2 icons ..... "Card" and "Tablet"
3- drag the 2 files into "card"
4- unplug the tablet
5- switch off tablet
6- volume up + power buttons till in recovery mode
7- select apply from external
8- then i get the message in red (( E:failed to mount sdcard (no such file or directory) ))
i dont know where am going wrong with this !!
hasson28 said:
7- select apply from external
Click to expand...
Click to collapse
Select "apply from internal"
Sent from my GT-P6210
Heya! I've followed the install instructions in this thread;
http://forum.xda-developers.com/showthread.php?t=1997251
I got to step 5, "enter recovery, on boot led will be violet for 3'', during this period press vol+ ".
I wasn't quick enough on pressing the volume button so it started loading wich didnt do much good i noticed after a while. (stuck on loading)
Soo, i removed my battery to restart the phone, after wich i managed to enter recovery mode only to find myself not knowing how to execute #6, "flash rom zip".
I tried this aswell;
"1) enter recovery at first : after u switch on d phone, when the pink light comes, press up volume key to enter recovery
2) connect your phone to computer using usb cable
3) go to mounts and storage and mount /system and /data.....this will enable ADB in recovery mode
4) now put ur rom zip in the ADB folder of ur computer and start adb and type "adb devices" (without the quotes)
5) if it shows some sort of numbers, then the device is connected successfully
6) in adb. type "adb push /ROM.zip /sdcard" (without the quotes) (ROM.zip is the name of the rom)
7) then reboot recovery, go to flash zip and chose the rom zip and enjoy!"
I fail at #5, since it wont show any numbers. It wont find the device. Many hours of googling and trying different things the result is the same, and im stuck with a phone that wont boot to OS.
What do i do now? Any help appreciated! :victory:
In recovery mode,
Install zip form SD card > install zip from external SD card (if you have put the downloaded zip in your external SD card)
Oh you have to press volume up and down to highlight option, and power button to select it.
Hit Thanks if I helped you!
satan89 said:
In recovery mode,
Install zip form SD card > install zip from external SD card (if you have put the downloaded zip in your external SD card)
Oh you have to press volume up and down to highlight option, and power button to select it.
Hit Thanks if I helped you!
Click to expand...
Click to collapse
My options is as follows;
1. Choose zip from sdcard (i can only access the Tipo internal memory from here, not my removable SD)
2. Apply /sdcard/update.zip
3. Toggle signature verification
4. Back
I can't access my phone storage from my PC either, since the drives wont show. I've tried all drives and such that i've found, but nothing works.
Is there any way i can reverse what i have done (remove clockwork or such) to get my phone to boot again?
Or a way to access my memory, so i can add the zip to the internal storage?
Have i bricked my phone?
Thanks!
You have not bricked your phone. relax.
Well you have to select first option, then under that there should be another line saying 'select zip from external SD card ' or something like that (if I remember correctly) . If that does not work there is a workaround where you use push file via adb. I'm not too familiar with that but will pm you if I find out where I read it.
And now- to revert back,
Download the world fs ftf file found here (its rootable) -
http://forum.xda-developers.com/showthread.php?t=2001567
Download flashtool latest (search) and install (fastboot and flash drivers in particular)
Place downloaded ftf file in c/flashtool /firmware
press flash and follow instructions.
Your on stock fw now. Remember to place zip in internal card if you are attempting cm10 again
Hit Thanks if I helped you!
Woo, somehow i managed to install the stuff! It wont send sound to my headphones though, other then that it's all good.
Thanks for taking your time!
To root plz follow guide: http://theunlockr.com/2012/05/22/root-huawei-ideos-x3-blaze-u8510-install-clockworkmod-recovery/
but the unroot guide did not work possibly coz of GB(GingerBread) stock but after a few min i accentally when to storeage in settings and was able to recover back to GB stock.
the UNroot method is the same up to step 7 of the unroot guide(http://theunlockr.com/2012/10/24/how-to-unroot-the-huawei-ideos-x3-blaze-u8510/) ie:
Stock download source (http://www.huaweidevice.com/worldwi...&directoryId=3372&treeId=0&tb=1&type=software) -get correct model number from behind the battery.
I. Before You Begin:
1. You must have a SD card formatted in FAT32 file system.(optional but not required, if already in use)
II. Downloading Required Files:
2. Download stock from manufactures source stated above (ie GB stcok for u8510-1 i believe there are only 2 one for tesc0 andPhones4U)
III. Unrooting the Huawei Ideos X3 Blaze (U8510):
1. Download and place the Stock ROM (zip file) on your Desktop.
2. Extract files from the Stock ROM archive to your Desktop. A dload folder should appear in the extract folder called dload and should contain UPDATE.app file.
3. With SD card inserted in your device, connect the device to your PC using the USB cable.( A message should appear click "turn on USB Storage" button)
Note: one can identify the sd card drive letter by the storage size,will not be exact size but approximation of size.
4. Copy dload folder and content to root of SD card (that is should be visible when sd card is opened possibly along with other folders)
5. Disconnect the device after the file has been copied.
Note:a) when the device is connected to PC it will be able to communicate with device, so may appear as its not there(connected to device)
b) plz backup all, as this process WILL DISTROY ALL DATA ON HANDSET!!
c) Check the folder and file is present in SD card by file manager-->sd Card
d) Lastly check batery level is full as a CRASH MAY BRICK THE HANDSET, So if not charge to full before going any further.!!!
Now Simply go to settings-->Storage-->Software Upgrade(scroll to bottom)-->SD Card Upgrade--> "confirm" --> "upgrade"
WILL TAKE "2 MINS"
WHAT TO EXPECT DURING THIS PROCESS (OF 2 MINS)
--------------------------------------------------------------------
STEP1/2 UNPACKING
and by 33% or progress bar reaching one third way, sign should change to read
STEP 2/2 INSTALLING
when completed the phone will boot 3 times with a few mins pause(each boot indicated with a virbration)
a WELCOME SCREEN should appear
"TAP GREEN ANDROID"
a sreen headed SETUP UP YOUR GOOGLE ACCOUNT
CLICK "SKIP"
a sreen headed USE GOOGLE LOCATION
CLICK "NEXT"
COMPLETED .....ENJOY
Hey guys,
I want to repair the i9003 for a friend and I'm a little bit confused o.0
I own a i9001 so I'm familiar with Odin and that stuff.
He gave me the device which only had access to the Download Mode. So I flashed a Stock ROM (MODEM, CODE, CSC, ...). It ended in bootloop and previous appeared note in recovery that it wasn't able a access to the sd card anyway ("unable to write to ums lunfile" and can't mount).
I flashed various Stock ROMs but everytime the same conclusion (bootloop). I've already tried to format/(un)mount sdcard through CWM but no chance.
Can anyone help? I read about a method where you have to open the device and connect something to the mainboard but it isn't my device, so I wouldn't do it.
Need help
rboy28 said:
Hey guys,
I want to repair the i9003 for a friend and I'm a little bit confused o.0
I own a i9001 so I'm familiar with Odin and that stuff.
...
Need help
Click to expand...
Click to collapse
if phone is rooted go this dir mnt/sdcard/(files)
u can do this with wondershare mobile go program (wondershare mobile go is a software that allow u to manage phone file edit or install app or read massage that nice):cyclops:
so.. mnt/sdcard(files) .export those files with wondershare mobile go from that toolbar .
see can u do this or u will get error during export(beware after export import it and make backup) ?or check it maybe these files are deleted and sdcard folder is empty like my problem.
all my regret is why i didnt backup from that.when i bought it first day.
anyway i have same problem .phone doesnt recognize int/ex sd card and unavailable keep goin thread to find .wont fix with flash by odin at all .
tell me about those files try find them maybe they are corrupted .like mine.i think must take it from other i9003 that hasn't sd card problem.when u find plz upload cuz i need too
and it this case problem will fix with a simple copy paste and if not u dont lose nothin
I can't do that. When I type "diskpart" in cmd.exe and "list disk" there will be no device found (only the hard drive in the computer).
But the PC recognize a device connected to it because in the taskbar the icon for a connected USB drive is shown.
In short:
- device doesn't boot normally (bootloop at logo)
- in stock recovery and CWM there is no internal sdcard shown ("E: can't mount sdcard")
- windows recognize a device but has no access to it
Is it possible to use adb sideload anyway on the i9003 or anything else where I can use adb.exe? I don't know if adb works in Download Mode ... does it?
I tried this CWM: http://forum.xda-developers.com/showthread.php?t=1351056 and an another one with green letters.
The first is quite outdated (packed in 31.01.2012).
Is there a newer one?
Here are photos what the Recovery (stock) says after Odin flash (stock firmare)
rboy28 said:
I can't do that. When I type "diskpart" in cmd.exe and "list disk" there will be no device found (only the hard drive in the computer).
But the PC recognize a device connected to it because in the taskbar the icon for a connected USB drive is shown.
In short:
- device doesn't boot normally (bootloop at logo)
- in stock recovery and CWM there is no internal sdcard shown ("E: can't mount sdcard")
- windows recognize a device but has no access to it
Is there a newer one?
Click to expand...
Click to collapse
i had exact same paroblem
do this maybe work (worked for me) .
this problem occurred when i used 16 gb toshiba as ex sd card (doesnt matter brand) after flash sd card and format it by pc that said ex sd remove unexpecteldy and turned off and whole battery charge was over. then i changed ex sd with my other phone and it work with no problem and when i replaced again 16 gb toshiba in phone ,again problem.
but after i format internal storage by phone from setting/phone storage . phone couldnt mount int sd till now.
so i inserted new ex sd and flashed whole rom with odin (MODEM, CODE, CSC, ...) phone started but without int storage i found out sd card directory is different and wont fix with flash STOCK ROM .but i doubt it for Custom ROM.
then i took ex sd card out from phone and turn it on again phone didnt boot up and was hang on samsung logo (same problem with 16 gb toshiba).then put that new ex sd card in and phone was boot up with no problem but int storage didnt come back..
so try with new ex sd and try flash rom (MODEM, CODE, CSC, ...) with odin then it will boot up.
---------- Post added at 07:59 AM ---------- Previous post was at 07:46 AM ----------
rboy28 said:
I can't do that. When I type "diskpart" in cmd.exe and "list disk" there will be no device found (only the hard drive in the computer).
But the PC recognize a device connected to it because in the taskbar the icon for a connected USB drive is shown.
In short:
- in stock recovery and CWM there is no internal sdcard shown ("E: can't mount sdcard")
- windows recognize a device but has no access to it
Is there a newer one?
Click to expand...
Click to collapse
after phone booted up again (in not case bootloop again)try root it with odin if u on 2.3.6 or super on click or other if u on froyo 2.2 then go turn on usb debuggin and use ''wonder share mobile go'' (software) and plug usb up run wondershare and it will recognize phone go to phone thorough wondershare if ur device is rooted u can access all phone files and folder then go to tis dir>>mnt/sd card/(files) <<<<upload for me these files
---------- Post added at 08:07 AM ---------- Previous post was at 07:59 AM ----------
rboy28 said:
I can't do that. When I type "diskpart" in cmd.exe and "list disk" there will be no device found (only the hard drive in the computer).
But the PC recognize a device connected to it because in the taskbar the icon for a connected USB drive is shown.
In short:
- in stock recovery and CWM there is no internal sdcard shown ("E: can't mount sdcard")
windows recognize a device but has no access to it
Is there a newer one?
Click to expand...
Click to collapse
and if ur int sd card come back again it will solve E:cant mount sdcard .first do two prior steps . for bring back internal sd again i think we need >>mnt/sdcard/(files) and copy paste those files in that location from other i9003 phone to our devices IMO cuz i tried many method they are useless. upper 60% im sure those files will revive int sd
I already solved it by destroying the internal memory on board and force install the stock ROM on an external sdcard. I successfully installed CM11 and it works except camera and downloads ^^
hi, have anyone found solution on this issue?
i am also facing same issue....
rboy28 said:
I already solved it by destroying the internal memory on board and force install the stock ROM on an external sdcard. I successfully installed CM11 and it works except camera and downloads ^^
Click to expand...
Click to collapse
Hi Friend,
I have the same problem. flashing Stock, Kernel , custom rom. Nothing make my phone successfully boot up.
Can you help me how exactly you did this. It might give a life for my friends phone too...
Remove or replace microSDCard.
Perform a clean flash with ddlf2 or original firmware.
And let us know how it went.
Also i see people saying this mistake several times...
Internal SDCard or SDCard stands for phone storage.
Emmc/External Storage/ External SDCard Stands for the microSDCard.
Noting that custom roms usually change the names.
With a custom rom the microSDCard is called emmc inside the system.
Please press "Thank" button if it helped you.
Sent from my GT-I9003 using XDA Free mobile app