Database Info

Prophet Speaker Crashed

I dont know what happend suddenly the speaker phone stopped working when I Was on speaker phone mode. I restarted the phone and tried all different kinds of ****. Finally I popped open the back camera cover and I could see the speaker. I was playing something on my Windows media and I could not hear anything. The moment I touuched the speaker with the stylus it started playing loudly but the moment I pull the stylus back it stops working. Can some one please explain me what is the problem with my speakers. Do I need to replace them ? if yes then where can I get them replaced in United states.

Yes mate, I had the same problem. I have a HTC Charmer and my speaker died while using tomtom. I openned and discovered the same thing, that touching the speaker causes it to respond again and dies again. Its basically the speaker "moved" too much for its own good and the wire carrying signal to its coil got damaged/broken.
While you could temporarily fix it by trying to glue the broken wire, it may not do any good. And can't solder it as the wire is stuck on the speaker cone surface which is plastic. For a few days mine worked by placing a flexible peice of plastic in such a way that it constantly applied very light pressure on the place where the wire was broken, and the contact was maintained, but obviously such a solution is short lived.
At present I am also looking for where to buy a spare speaker from, but can't help you in this regard as am in UK.
Hope this helps in some way.

Happened to my Prophet. It's currently away for a warranty repair.
Seems like a very common problem.

Microphone ~ Software or Hardware?

I been experiencing major problems with the microphone while making calls , in the last 2 weeks ! People tell me it sounds like Im talking with the windows open while driving 100 miles an hour, like I have a speaker phone turned on, not sure what this could be , sounds more like a hardware issue than a software , si anyone else having issue with this on a Samsung phone , I bought the phone new in November when they came out!
The only other hardware issue Ive had is the USB port , broke off , I soldered it back and have never had a problem since ,

Maybe you somehow screwed the mic while soldering USB connector? Or when taking it apart.

I dont know how that could be , the mic is on the other end of the phone and its under the "lower" pcb board , I never took that part out!

Fixed it , it seems the using the settings in the diagnostic app to increase the volume , changes the the sensitivity to the mic (at least it did with my phone) I changed it back to the default settings and it works fine now!

[Q] is my transformer speaker wire loose?

i found similar threads and posts but none with this specific problem. i have a b90 from bb, 12/11/11. yesterday out of no where, i lost sound. long story short after reboots and wipes, realized when i rotate or ecspecially shake my tf101, my speaker cut on, then off. when i press hard on the bezel in the middle, they come on briefly. sometimes they stay on.
any insight or answers to solve this so i dont have to do the rma process would be greatly appreciated. after purchase from bb for 299 ( cheaper build to reduce price maybe) i became an asus fan. now, i am really dissapointed in quality since other then this, my tablet is physically flawless and hasnt been dropped or damaged.
edit: both speakers do work when they decide to come on, and heaphones work. thnx in advance

I have cut out and removed my right speaker because it was dead, waiting on an order from asusparts.eu for a replacement speaker
It wasn't a loose wire, it was the connection to the actual cone that was bad, pressing in the middle of the speaker brought it to life for the first time since I bought it, but nothing I could do to fix it, they are more or less sealed and too tiny to fix

so you believe its the speakers? they both seem to work, they just aren't outputting sound until I shake the tablet, push, or sometimes face down they work

Why not just rma it?

dangambino said:
so you believe its the speakers? they both seem to work, they just aren't outputting sound until I shake the tablet, push, or sometimes face down they work
Click to expand...
Click to collapse
Couldn't say for sure, but it sounds like something you could fix yourself if shaking it brings it back on, if you don't mind losing warrantly opening it, but bear in mind, my speaker replacement has already taken 2 weeks and they are not expecting parts until the end of february, so RMA might be quicker, depends if you can put up being without it for a while

honestly i dont want to be without my tf. silly huh. its weird though i just discovered that like i mentioned, headphones work fine, however after i unplug the headphones the speakers immedfiately output sound and continue to do so until i change to another app. e.g.- while watching netflix, then back out and open a game with sound, it doesnt output untilni plug and unplug headphones. this seems to be the best way to get speakers to play.
they donteven seem to cut out with movement afterbthe headphones are unplugged. only when exiting out of current app, then attemptingbtonopen a new one. what is the issuer here?
im lost ast this point. rma aside, this has me curious now
id probally be willing to do it myself, if i knew exactly what i was replacing or repairing or rigging. i purchased a kit with the neccesary t5 torx, and phillips to remove bezel.
how tight should the screws be on the bottom of the tf. i dont want to overtighten. got some petty hope that tightening the screws will help. more sillyness im sure.....
this stinks though cvuz this just happened. you know? thnx in advance.
also lookimg at bluetooth speaker as an alternative

Speakers working after you remove the headphones but stopping again once you launch another app ?
You tried a factory reset in-case its a software / firmware bug ?
Screws just need nipping up, not tightened too much or you`ll either thread the holes or snap the head of the screw

Just RMA it, man.

[ FEITENG H9500 ] Known issues and fixes

Ok.. i see many people on this forum asking questions about this device.. the truth is this device is designed very poorly and it even may arive at your hands defective / with some or with a lots of problems.. you can proceed by your very own responsibility. Take a look in the picture for pcb details
- to Fix about every problem you need to findout how to unscrew the back plastic case and be able to see its PCB (Printent circuit Board) - Its pretty easy, just remove the little screws and give a presure at the clips of the cover to be removed, don't use metal objects because you will scratch the plastic.
* WIFI / GPS very low signal
Let me begin with one problem that you have FOR SURE.. is the low wifi signal and gps.. this is due to a horible design of the antenna.. the antenna is not just horrible, but it is also causing a short circuit it self! which is the main reason why the signal is low. First you have to stop the short circuit from happning
How to fix it? Unscrew the back cover, at the top of the back cover under the flash you will see a white sticker, this is the antenna, you have to remove completely this white sticker because it can't be useful by any way. Remove every piece of it including the copper-yellow color from the inside (the place that makes the connection.
Now find a UTP cable and take a piece of a hard copper of it, remove the plastic and keep the copper wire clear, cut it and place it in the whole were previewsly was the white sticker.. you have to place it in this way so it can connect with the inside conntact with the back plastic is placed and screwed again on the phone.. there are 2 pins in that place.. the old antenna used both of this pins (that was causing short circuit) you have to use the left pin and leave the right pin completely empty.. so the right pin doesn't connect anywere, and the left pin is connected to your piece of copper wire.
Cut the copper at the same size of the top of your phone.. so you can place it horizontal ... but you can also try vertical, (use wifi analyze app from play store to see what fits better for you)
Now.. this is the same antenna for gps.. you have nothing else to do.. just install GPS Test app and go outside and test your gps..
This is what i did and im pretty happy with it, instead i used 2 pices of copper and i covered the whole top place of my phone under the camera.. but that doesn't mean is the most right way because when we dealing with antennas there are a lot of math / and calculations that have to be done to design a perfect antenna.
the wire gives really a great signal.. just in case you want to reach the extreme.. Instead of copper wire you can use thin-Copper paper. (don't use foil of aluminium is not good) and design a better antenna copying the design of an antenna from another phone (that you know it works)
* Camera autofocus doesn't work - Or camera doesn't work at all
[Don't unscrew] Frist thing you should try is remove the back cover and give a presure in the right side of your camera with your finger.. this is the place the connector is located.. and it may gets unclipped and loose the connection after a small drop or something. After that Reboot the phone.
[unscrew back] If this presure on the right doesn't fix it, then you have to unscrew the phone.. take off the camera and give it some small hits and punches.. place back the camera and see if it works.. this is due the autofocus motor got stuck.
* Mic, Speaker, USB doesn't work
[Don't unscrew] This is due the connector of the bottom part got lost its connection. remove the back cover and give presure under the place of the SIM cards, were it writes 'WCDM' and 'GSP'. press a bit those spots. reboot, if not fixed:
[unscrew back] The two bottom connectors is 1. for the touchscreen and 2 for the bottom parts.. you need to check both of those because i am not sure which is which.
* SIM1, SIM2, Microsd not working
[Don't unscrew] Try to give some press next to vol+ / vol- buttons
[unscrew back] On the top left of the PCB there are located 2 connectors, 1 is for the front camera, and 2 is for the SIM/SD parts.. the last connector to the side of vol buttons is the connector you have to check and press to make sure is connected ok.
* Touchscreen doesn't work
[Don't unscrew] Give presure right under the headphones jack
[unscrew back] This is were it is located.

Charging Problem
I would like to add the problem with charging the batteries.
I got a new H9500, with two batteries. When i try to charge it with the adapter that came with it, the phone shows the charging animation, but it never actually charges the phone.
I have the same behaviour on both batteries.
After searching for a solution i found these:
-The charger supplied is 5V, 0.5A. Some people used a 1A charger and got to the point that it actually started to charge
-ROM problem, by changing the ROM some people were able to fix the problem, since the software was not getting correct info out of the battery's third pin.
Well none of the above worked for me. I hope someone comes up with an altarnate solution.

I need a new usb pcb for my feiteng H9500 (the usb port is broken on it)
This is the part I need :
the ones on aliexpress and dhgate don't ship to tunisia :/

my expirience
Hello guys...
My story. Bought this phone for my son for 160 €. We found out that camera focus didn't work, so I took it apart.
The easiest way to take down plastic cover, after it was unscrewed, is to put something plastic under it in the place between both SIM cards places, and work around inner battery square.
When cover was off, I found out that camera plug (right of camera) wasn't even plugged in. It only laid on connector. Plugged it in, and shake camera a little and auto focus came alive.
After that I noticed that black cable between gsm antenna and PCB was very loose, so I had to sort this out
At the end I found out that speaker connections are very delicate and had to take plastic down again to properly connect speaker.
Now it is obvious to me, why these Chinese phones are so cheap. We have saying in our country: pay little, get little
But now everything is cool and my son is happy.... And I am happy

Hi.
I just got a Feiteng H9500. The problem is that the camera is not working and the camera application hangs then stop responding then quit. When I start the camera nothing apears on display. I've put some pressure then some hits and it started to work a while. The focus worked as well but It seems to me not to work excellent so I gave it more hits, then the camera stopped working again. I have disassembly it, i moved a bit the camera and removed and put back the connector and it came alive again for a while, but just the front camera. Then stopped again. I have noticed that the camera doesn't move up and down when I press on it, it is stopped down, if I lift it with a needle it goes up, so it's not stucked.I can't even comute between cameras because the aplication hangs then quit. ( Everything else works.
any help? Thanks.

Hi Guys,
Just ordered the HTM H9500, is it exactly the same Phone as the Feiteng H9500?
I mean can I use ROMs for the Feiteng H9500 to flash them on the HTM H9500?
Big Thanx

cologne83 said:
Hi Guys,
Just ordered the HTM H9500, is it exactly the same Phone as the Feiteng H9500?
I mean can I use ROMs for the Feiteng H9500 to flash them on the HTM H9500?
Big Thanx
Click to expand...
Click to collapse
My phone is Feiteng H9500 (HTM).
Appearance is similar FEITENG h9500, but not identical.
I'm not sure that have the same Rom, so I did not dare to flash a custom ROM.
View here:
http://www.movilesdualsim.com/forums/feiteng-h9500.166/

I cannot read Spanish or whatever it may be
There is a ROM at needrom called something like this "feiteng / htm h9500".
That sounds like the device is the same...
Gesendet von meinem GT-I8190 mit Tapatalk

b0li said:
Hello guys...
My story. Bought this phone for my son for 160 €. We found out that camera focus didn't work, so I took it apart.
The easiest way to take down plastic cover, after it was unscrewed, is to put something plastic under it in the place between both SIM cards places, and work around inner battery square.
When cover was off, I found out that camera plug (right of camera) wasn't even plugged in. It only laid on connector. Plugged it in, and shake camera a little and auto focus came alive.
After that I noticed that black cable between gsm antenna and PCB was very loose, so I had to sort this out
At the end I found out that speaker connections are very delicate and had to take plastic down again to properly connect speaker.
Now it is obvious to me, why these Chinese phones are so cheap. We have saying in our country: pay little, get little
But now everything is cool and my son is happy.... And I am happy
Click to expand...
Click to collapse
Thanks to your photo guide, I found courage and disassembled my HTM H9500 and DG300 phones and fixed them easily (nothing to fix really, just blow off some dusts between camera connectors and in front speaker)

wassgha said:
I need a new usb pcb for my feiteng H9500 (the usb port is broken on it)
This is the part I need :
the ones on aliexpress and dhgate don't ship to tunisia :/
Click to expand...
Click to collapse
You should order it by the store you got the picture of it. actually there are many stores selling parts for this phone.. almost like its branded.. unlike with other chinese phones you get a struggle to find parts, so you shouldn't face any problem to order a part.

Sound when touch on Lock Screen
hi, guys
I have FEITENG (HTM) H9500 almost a year and I am very pleased with it.
I want to change the sound of the screen when touch lockscreen, but I do not know how.
It did not sound when unlock the screen, it is the sound when you put your finger on the screen while the screen is locked.
In The system/media/ui is not, and I do not know where I'd be looking elsewhere.
Please help

No Data connection
I have had a Feiteng H9500+ for a while but recently rooted it and tried some different ROMs as well as applying a GPS fix. Somehow now my AT&T data connection is not working. The SIM settings have the data on and set to AT&T and I turned roaming on just to be sure but nothing I do can get the AT&T data to work. When I am connected to Wi-Fi it works fine. This is the only way I can get Internet.
Can anyone help me get my mobile data working again?

Question Charging port, vibration motor, sound and microphone doesn't work after a drop.

Hello, I recently got a Galaxy A22 5G, the user dropped it on the ground, and after that the phone doesn't charge, vibration motor also doesn't work, sound, microphone and speaker too. It turns on though and it's working fine (except the other problems mentioned). The phone doesn't have any cracks or scratched so I am guessing the drop wasn't very hard, is there any chance to repair it without paying a lot? I am guessing maybe a cable disconnected internally, or maybe the board just got damaged, I don't know.
Did anybody experience the same issue before?

Yeah. I guess it was a problem with the board. I just got a new phone after that.

Arm1nas said:
Hello, I recently got a Galaxy A22 5G, the user dropped it on the ground, and after that the phone doesn't charge, vibration motor also doesn't work, sound, microphone and speaker too. It turns on though and it's working fine (except the other problems mentioned). The phone doesn't have any cracks or scratched so I am guessing the drop wasn't very hard, is there any chance to repair it without paying a lot? I am guessing maybe a cable disconnected internally, or maybe the board just got damaged, I don't know.
Did anybody experience the same issue before?
Click to expand...
Click to collapse
most likely you have disconnected the cable that connects the motherboard and sub-board, so the repair will not be expensive, maybe even free if you have the skills to open the phone sorry for my English