WARNING! rooting your phone can void your warranty, do so at your own risk.
NOTE: These instructions below assumes you have a brand new phone just out of the box, all settings on default. If the default settings have been altered, please make sure you have the Ractivation Lock turned off in settings/Security or you will get a FAIL! message in Odin. (Thanks to Girn for pointing that out)
Download Kies (for the Drivers) from here http://www.samsung.com/ca/support/model/SM-N900WZKEBWA
If you don't use Kies just uninstall it as soon as the Kies install is complete.
During Kies uninstall it'll ask you if you want to keep the drivers, say yes to keep drivers.
Very Important! for Chainfire's rooting method to work, you must flash this tar via Odin, before you flash TWRP recovery, else it might Fail!
Download Chainfire's package from post #3
Select the file for the SM-N900W8 Canadian version, it includes the Odin and the Tar file to root your Notes 3.
Follow the flashing instructions from Chainfire's post #2
Quick Root Steps:
- (USB) Disconnect your phone from your computer
- Start Odin3-vX.X.exe
- Click the PDA button, and select CF-Auto-Root-....tar.md5
- Put your phone in download mode (turn off phone, then hold VolDown+Home+Power to boot - if it asks you to press a button to continue, press the listed button, or run adb reboot download command)
- (USB) Connect the phone to your computer
- Make sure Repartition is NOT checked
- Click the Start button
- Wait for Android to boot (like 5 seconds)
- Done
Important! make sure you Download TWRP version 2.6.3.2 (or newer) for hltecan models from http://goo.im/devs/OpenRecovery/hltecan
Quick TWRP Steps:
- (USB) Disconnect your phone from your computer
- Start Odin3-vX.X.exe
- Click the PDA button, and select openrecovery-twrp-vX.X.x.x-hltecan.tar
- Put your phone in download mode (turn off phone, then hold VolDown+Home+Power to boot - if it asks you to press a button to continue, press the listed button, or run adb reboot download command)
- (USB) Connect the phone to your computer
- Make sure Repartition is NOT checked
- Click the Start button
- Wait for Android to boot (like 5 seconds)
- Done
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Quick Reference Memo:
Wind version is model SM-N900W8
Batch of 13.09 (Sept 2013)
Seems like all Canadian carriers are running the same model, no more worries about picking up the right model for 850/1900 or 1700/2100.
Internal Storage: 32GB
Stock Battery type: B800BU 3200 mAh
Connectivity:
WiFi 802.11 a / b / g / n / ac (HT80)
GPS / GLONASS
NFC, Bluetooth® v 4.0 (LE)
IR LED (Remote Control), MHL 2.0
Sensor:
Gesture, Accelerometer, Geo-magnetic, Gyroscope, RGB
Proximity, Barometer, Temperature & Humidity, Hall Sensor
Full Specs at Samsung: http://www.samsung.com/global/microsite/galaxynote3-gear/spec.html
Baseband (Radio):
N900W8VLUBMI5 (from Sept 2013 stock ROM)
N900W8VLUBMJ1 (from Oct 2013 stock ROM)
WARNING! Do NOT use RegionLock Away on Note 3 (SM-N900W8)
It will SIM Lock your phone, and ask your for the unlock pin code, even when you are on the same carrier using the ssame carrier SIM card.
In case of Force Closes after restoring Backups from Ti:
http://forum.xda-developers.com/showthread.php?t=2463116
Code:
su
restorecon -R -v /data/data
To Disable the annoying KNOX security:
http://forum.xda-developers.com/showthread.php?t=2471695
Code:
su
pm disable com.sec.knox.seandroid
Alternative Method To Disable KNOX
Using Titanium Backup, or any other App that has the ability to FREEZE find these files to freeze them:
Code:
com.sec.enterprise.knox.attestation 1.0
com.sec.knox.eventsmanager 1.0
KLMS Agent 1.0
KNOX 1.0
KNOX 1.0 (link)
Knox Notification Manager 1.0
KNOX Store 1.0
Found a bunch of STOCK ROMs for SM-N900W8:
here http://www.samsungis.com/Firmwares/SM-N900W8.html
Windmobile
Bell
Rogers
Telus
Koodo
Mobilicity
Sasktel
and other Latin America countries as well if you prefer stock ROMs from Claro, Telcel or any other provider.
Additional mirror repository, for SM-N900W8 ROMs and flasha-able modems
http://forum.xda-developers.com/showthread.php?t=2488268
Troubleshooting Steps for failed Chainfire's rooting via Odin:
Do not fled if you can't get Chainfire's tar to flash properly.
- If you are unable to Boot, then go back into Download Mode.
- Flash back any stock SM-N900W8 ROM via Odin
- Then skip Chainfire's rooting Steps, and instead go straight into the TWRP steps
- Once you have TWRP installed, restart the phone
- Boot into TWRP (Vol-Up + Home + Power)
- Once inside TWRP just select the option to reboot, pressing on any of the reboot actions will prompt you with
"Your phone doesn't seem to be rooted, Do you want to install SuperSU?"
answer Yes by swiping
- Reboot to System, then run SuperSU
- When SuperSU is up, it'll ask you if to flash the root binaries, select the TWRP method
- The phone will reboot again into TWRP installing the root, when done, just reboot back into system.
- Done
Pics:
TWRP working
No Buttons problem
Version & Model from inside the battery compartment
Using the Puerto Rico ROM
Good to see a post on our Canadian models for once! Stock recovery should be in there also that I provided Dees _ Troy 2 days ago
Sent from my SM-N900W8 using Tapatalk 4
AllGamer said:
No Buttons problem
Click to expand...
Click to collapse
No buttons problem?
Did you buttons stop working??
I'm gonna try this guide out when I get the phone.
http://forum.xda-developers.com/showthread.php?t=2470262&page=3
Sent from my Nexus 4 using XDA Premium 4 mobile app
nicholaschum said:
No buttons problem?
Click to expand...
Click to collapse
Girn said:
Did you buttons stop working??
Click to expand...
Click to collapse
on this other Thread http://forum.xda-developers.com/showthread.php?t=2471367
people were complaining about misaligned or loose button problem
AllGamer said:
on this other Thread http://forum.xda-developers.com/showthread.php?t=2471367
people were complaining about misaligned or loose button problem
Click to expand...
Click to collapse
So you're having no issues? Did you first have to disable the "reactivation lock" in settings? As per the link I posted in my first reply.
Sent from my Nexus 4 using XDA Premium 4 mobile app
AllGamer said:
on this other Thread http://forum.xda-developers.com/showthread.php?t=2471367
people were complaining about misaligned or loose button problem
Click to expand...
Click to collapse
Oh right, I thought there was a bug going around that made the buttons stop working after root, like my S2 LTE.
Girn said:
So you're having no issues? Did you first have to disable the "reactivation lock" in settings? As per the link I posted in my first reply.
Click to expand...
Click to collapse
Nope, at least not that I know of.
I'm using it right now, I can make calls, receive calls, SMS, 3G/4G data, everything work
Do you have a screen shoot / pic of the "Reactivation Lock" you are talking about?
or describe to me where I should expect to see that message?
Look at the thread I linked. It's also a root guide for Canadian note 3.
He says you have to disable reactivation lock or you'll get failed msg when trying to Odin
Sent from my Nexus 4 using XDA Premium 4 mobile app
Girn said:
Look at the thread I linked. It's also a root guide for Canadian note 3.
Click to expand...
Click to collapse
***Please note you must have the reactivation lock turned off in settings/Security or you will get a FAIL message***
Click to expand...
Click to collapse
^
That?
Nope, i did not have to do that before flashing both Tar files.
You can see my screen shot above both were Green Pass!
--- Edit ---
Okay, I just figured that out.... by default that option is OFF, that's why i didn't have any issues.
Ok thanks. You able to run greenify and hibernate apps without any issues?
Sent from my Nexus 4 using XDA Premium 4 mobile app
Girn said:
Ok thanks. You able to run greenify and hibernate apps without any issues?
Click to expand...
Click to collapse
I do use greenify.
I'll let you know when I'm done restoring all my Titanium Backup, the first time restore i was trying to restore also System Data, and needless to say that went awry
so, this is the 2nd try without the System Data, I should work OK, unless i get into this other issue. http://forum.xda-developers.com/showthread.php?t=2463116
Code:
su
restorecon -R -v /data/data
restorecon -R -v /system
AllGamer said:
I do use greenify.
I'll let you know when I'm done restoring all my Titanium Backup, the first time restore i was trying to restore also System Data, and needless to say that went awry
so, this is the 2nd try without the System Data, I should work OK, unless i get into this other issue. http://forum.xda-developers.com/showthread.php?t=2463116
Code:
su
restorecon -R -v /data/data
restorecon -R -v /system
Click to expand...
Click to collapse
Why are you trying to restore anything? Does rooting or installing the recovery, erase the phone?
Sent from my Nexus 4 using XDA Premium 4 mobile app
Girn said:
Why are you trying to restore anything? Does rooting or installing the recovery, erase the phone?
Click to expand...
Click to collapse
oh no, it has nothing to do with recovery or rooting.
those are just my Apps & Games, settings and data.
AllGamer said:
oh no, it has nothing to do with recovery or rooting.
those are just my Apps & Games, settings and data.
Click to expand...
Click to collapse
Why are you restoring then if you don't mind me asking. It because you had to unlock the boot loader? (Don't have my note yet)
Sent from my Nexus 4 using XDA Premium 4 mobile app
Girn said:
Why are you restoring then if you don't mind me asking. It because you had to unlock the boot loader? (Don't have my note yet)
Click to expand...
Click to collapse
Migrating all the data from the Old Note 1.0 to Note 3.0
Games Saves, Application data, etc
Oh I see thanks!
Sent from my Nexus 4 using XDA Premium 4 mobile app
Anyone have the Note 3 from Wind? Just wondering how it is performing for everyone. I am with Telus right now but the plan is way to expensive for me at the moment so I want to buy a Note 3 from Wind soon.
Related
THREAD INDEX:
POST #1 = ROM info and download
POST #2 = How to extract a compressed file
POST #3 = Directions on flashing odin written and visual
POST #4 = TroubleShooting
POST #5 = Random post lol
POST #5 = Credits
Original content from AC:http://forum.androidcentral.com/cha...ed-beast-alpha-voodoo-clockwork-ed2-root.html
you will find me there most of the time.
Click to expand...
Click to collapse
XDA, jt1134, nor myself are responsible for modification done to your phone. This includes, bricking, exploding, spontaneous combustion, or it running away with your significant other!!!
Click to expand...
Click to collapse
EXTRA SPECIAL THANKS TO jt1134 FOR DEVELOPING THE FIRST VOODOO KERNEL. NOTE I WAS NOT INVOLVED WITH THE DEVELOPMENT OF THIS KERNEL.
Click to expand...
Click to collapse
PLEASE BE KIND THIS IS MY FIRST ROM
This Rom is SUPER ALPHA so do not tell me that you want this or that give me a chance to work on it please.[/quote][Note]
This ROM is fully Deodexed, but only Partially debloated as time goes on i will keep debloating deeper and deeper.
List of thing to do:
ED2 update
Full Deodex
Full Debloat
Black Status Bar
Dark themed Market
Dark google search
Change Colors on touchwiz theme (Work in progress but accomplished)
Remove touchwiz launcher
Replace Launcher (Launcher Pro for now)
Quickboot app (to boot into clockwork)
AOSP unlock screen (courtesy of nitsuj17)
Accurate battery mod (courtesy of nitsuj17)
Clockwork recovery (Modified by jt1134 )
Voodoo ext4 lagfix (courtesty of jt1134)
Themed Dialer
Themed Swype
Altered Beasts Themed Dock and Icons
Transparent notification pull down
Animated text notifications
Power button boot options[/note]
[INFO]THIS IS THE GOAL TO WHAT THIS ROM WILL LOOK LIKE, IT IS NOT THERE YET SO DONT ASK WHY IT DOESNT LOOK LIKE THIS PLEASE
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
[/INFO]
For those that ask if there is lag
This is still an ALPHA build so please do not be to critical, it needs alot of themeing to be done and there is more i need to put on but i think everyone will be happy with the direction this is going with. This is inludes everything Striked off the list of things to include above.
After flashing it will boot right into clockwork, press power to reboot. Clearing cache partition and Dalvik is not a bad idea but if you dont it wont hurt anything.
[tip]If you do not already have voodoo installed boot time should be 5-7 mins do not panic just be patient.[/tip]
DOWNLOAD Altered Beast voodoo+cwm here:
Code:
Altered Beast Alpha 5 (to be flashed in CWM) this does not contain a kernel but is a full system flash not a patch
Change log 6/20
Hulu (on boot, before you sign into google, go to settings privacy and make sure auto restore is not checked. Also make sure flash doesnt update)
voodoo control app
alot of themeing by gunner and myself
new tv shutdown animation that i modded up
charging fixed
aosp launcher themed up by me
Teamnew widget added
Androphile wallpapers added
icons added to /system/icons may need ES explorer or root explorer to get to them
For those of you who dont know how to use clockwork there is plenty of info on this site, otherwise wait till tonight or tomorrow and i will be opening a new altered beast thread as this one is cluttered[/code][/CODE]
Change log: 5/27
Clock fixed
Voice input fixed
Partially themed
Flying windows added
Change log:5/26
Calendar fixed
Visual voicemail fixed
Dark Angel USB mod made
Carbon fiber quickpanel added
Hulu Patch: (Flash with clockwork)
AlteredBeast_Hulu_patch.zip
apks :(move to /system/app folder then reboot your device)
Calendarprovider.apk
VVMservices.apk
DeskCradle.apk
GoogleCalendarsyncAdapter.apk To fix Calendar problems
Extracting a compressed file (ex. zip or rar)
1.) Download and install Winrar HERE
2.) Locate the compressed file you would like to extract
3.)Right mouse click on the file icon a drop down menu will appear , select Extract Here
4.) You will then see a progress pop up window that will appear then when completed will close itself
5.)This will leave an extracted file in the destination folder
Congrats you have successfully extracted the compressed file it is now ready for use
To install ODIN packages on your device
1.Download and install drivers on your computer HERE
2. Next you will need to download the Altered Beast zip file from post #1 which will be extracted and placed in the PDA section of ODIN:
3.) You will need to download the ODIN application tool found here ODIN or ODIN MIRROR
4) Extract the Altered Beast zip file to get the .tar.md5 file
5.) If your phone is plugged into your computer, unplug it now.
6.) If your phone is not powered down, power it down now.
7.) Remove battery from phone.
8.) Launch ODIN on PC.
9.) Plug USB cable into phone.
10.) Plug your Droid Charge into the PC via the USB cable that came with your phone.
11.) Press and hold the volume down key until (approx 3 secs) you see a gigantic yellow triangle on your phone, and your phone will be in download mode. The first thin rectangle in the upper left of the ODIN applicate should also turn yellow and identify a com port. You can now release the volume key.
12.) Click on the PDA button in ODIN
Triple check that you pushed the PDA button. Do NOT click the Phone button prior to continuing to step 13. If you choose Phone, you will have bought your Fascinate a one-way ticket to hell.
13.) Find and double click on the Altered Beast .tar.md5 file you downloaded & click the Start button. (This should take approx 3 to 6mins)
14.) Phone will power down when finished.
15.) Close ODIN, remove USB cable from phone, reinsert battery, power on phone and let ROM fully load.
[TIP]It may boot into stock recovery simply Press the home button to reboot
It is also advised to wipe cache partition while you are in recovery [/TIP]
******************************************************************************************************************************************
[INFO]Visual Instructions [/INFO]
First you must download
Odin v1.3
Once odin is downloaded open it, its an executable file so when you open it you will see the following :
Once this is up, do the following
-Remove the battery from your Device
-Plug in the USB cord
-Hold down the Volume Down button until you see a big bright triangle on your screen , underneath it will say Downloading and beneath that it will say Do not turn off target
At this point you will see one of the boxes in the corner turn yellow, letting you know there is a connection, it will look like this
after you are connected you want to hit the PDA button, NEVER PHONE, phone will erase your modem and you will have trouble connecting after that at all.
when you click the PDA button a pop up will appear and you will need to select the file you would like to flash and then click open
now you will see the file appear in the PDA window ,, with connection made and the file in the PDA window, you may now hit Start
Once you hit start this process Should take approx. 5 mins if you are returning to stock . shouldnt take any less time than that and not much more. So dont start freaking out at min 2...(wait till min 7) lol
If you are flashing a Clockworkmod file it should take approx 7seconds.
once it is completed you should see the following window:
Once you have reached this screen it is safe to unplug , put your battery in and boot up..
Trouble Shooting
Odin application displays one of the following in message box OR Odin is locking up in the middle of the process
<OSM> All threads completed. (succeed 0 / failed 0)
Click to expand...
Click to collapse
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Resolution
90% of problems associated with Odin are due to communication between phone and computer
Reboot your computer
Redownload the odin package
Use USB ports in the back of the computer, if you already are use a different port
Make sure you did not forget to remove battery from phone (Should be out the ENTIRE process)
make sure Odin is the only application running and Antivirus is DISABLED
If you are using a laptop make sure its plugged in also find the nearest desktop and try from there
****************************************************************************
After failed flash with odin upon power up the following is depicted on the screen
SOFT BRICK
Resolution
First off DO NOT PANIC. there is a simple solution, just remove the battery , plug the phone into the computer, press and hold volume down and it will enter download mode. Please review all the steps oulined in this thread and try and flash again
Credits
AC Member drewwalton19216801 for assistance deodexing
AC Adviser Paul627g giving instructions on themeing
AC Moderator Ragnarox for overall advise on Roms
AC Super Moderator gbhil for assistance on pushing deodexed folders to system without clockwork
XDA Developer jt1134 for developing the Voodoo Kernel
XDA Developer nitsuj17 for aosp lockscreen mod
So we can't install this through cwm right(if we already have it)?
Sent from my SCH-I510 using Tapatalk
Grillrd said:
So we can't install this through cwm right(if we already have it)?
Sent from my SCH-I510 using Tapatalk
Click to expand...
Click to collapse
no i honestly i am not sure how to make it in zip flashable form yet hopefully a developer will show mercy upon me lol and show me how its done
I'm game!
Downloading now.
Just wanted to give y'all a big "THANKS" for all you do!
This is the first time I've flashed a ROM in a long time. SO far, it's been fun - let's see what this one does!
EDIT #1
WooHoo!
After rebooting, it booted into recovery mode (Red Text), so I just rebooted, and it went to the "Red Eye", and about 2 minutes later, we're golden!
BTW, the boot animation is still 'glitchy'. Could this be from my original flashing of v4 Kernel?
EDIT #2
Looks like email is missing....no ability to add either POP email or Exchange email, unless I'm missing something.
Thank you for the ROM ...loaded up perfectly. Are you planning on keeping the background image for the notification pull down or going with a solid color/transparent?
Rom is amazing.
UPDATE: nevermind, found the solution in the thread on androidcentral.
Thanks!
Ok, the rom booted up great. But I'm having calendar problems. I downloaded both the .apks. The calendarsync installed fine, but my accounts say sync is experiencing problems and will be back shortly. So I tried to install the calendarprovider and it won't install.
Help??
Thanks!
teddykgb715 said:
UPDATE: nevermind, found the solution in the thread on androidcentral.
Thanks!
Ok, the rom booted up great. But I'm having calendar problems. I downloaded both the .apks. The calendarsync installed fine, but my accounts say sync is experiencing problems and will be back shortly. So I tried to install the calendarprovider and it won't install.
Help??
Thanks!
Click to expand...
Click to collapse
Appears to be working just fine for me. Did you move both apks to system/app and reboot?
ColSaulTigh said:
EDIT #2
Looks like email is missing....no ability to add either POP email or Exchange email, unless I'm missing something.
Click to expand...
Click to collapse
I think in the ROM imnuts created, he removed the stock samsung email app. Unless you're talking about something different entirely.
Wow, this ROM looks amazing! Seriously cannot wait to see how it progresses.
Keep up the great work! Followed your instructions and everything is going great. I'm about to download those apks and put them in the place to fix calendar.
anyone on that has the calendar problem?
Im using this rom and dont have the calender bug. Only.bug ive seen so far is when deleting a contact it erases it then force closes on me. But it still does its job so its all good
Sent from my SCH-I510 using XDA Premium App
Z51 said:
Im using this rom and dont have the calender bug. Only.bug ive seen so far is when deleting a contact it erases it then force closes on me. But it still does its job so its all good
Sent from my SCH-I510 using XDA Premium App
Click to expand...
Click to collapse
can you give me the permissions for
calendarprovider.apk
googlecalendarsync.apk
and if you also have the VVM problem permissions for that aswell
Z51 said:
Im using this rom and dont have the calender bug. Only.bug ive seen so far is when deleting a contact it erases it then force closes on me. But it still does its job so its all good
Sent from my SCH-I510 using XDA Premium App
Click to expand...
Click to collapse
For some reason, I can't even access the Calendar on my phone. It's not even in the app launcher or anything like that. The widget still works, but even from the widget, I can't open the calendar. Any ideas?
nvikram said:
For some reason, I can't even access the Calendar on my phone. It's not even in the app launcher or anything like that. The widget still works, but even from the widget, I can't open the calendar. Any ideas?
Click to expand...
Click to collapse
go to the OP download the 2 calendar apk and then use root explorer or another manager to move it to /system/app, then reboot the phone let me know if it works
I live in Japan and just go a Samsung galaxy tab 7.7 plus. I am looking to root the device and if possible flash a stock ROM or others. I have look on the forum and cannot find any info on a SC-01E... Any guidance would be great. ^^
The model number is SC-01E
Android Ver:4.0.4
baseband ver: SC01E0MLJ3
Kernel Ver:3.0.8-1131726
sloppy1969 said:
I live in Japan and just go a Samsung galaxy tab 7.7 plus. I am looking to root the device and if possible flash a stock ROM or others. I have look on the forum and cannot find any info on a SC-01E... Any guidance would be great. ^^
The model number is SC-01E
Android Ver:4.0.4
baseband ver: SC01E0MLJ3
Kernel Ver:3.0.8-1131726
Click to expand...
Click to collapse
I have a Samsung galaxy tab 7.7 plus just like u ,but simcard is locked,i have no the number,how to do?
Hey Guys,
There is a separate XDA Forum for the 7.7 Plus :
http://forum.xda-developers.com/forumdisplay.php?f=1427
Thread moved .
I also want to do the same with my device, searching I found this:
"Galaxy Tab 7.7 Plus(SC-01E)のrootを取ってみる
Android Hack デジタルガジェット Galaxy Tab 7.7 Plus
近頃たたき売られているGalaxy Tab 7.7 Plus
先月なら、苦労せずとも新規一括0円が転がっていましたね。
docomoなiPhoneが発表されるまでは叩き売られてそうですよね。
私はキャッシュバックまで頂いて手に入れてきました。
ということで、rootを取ってみたいと思います
準備
SC-01E／SC-01D／SC-03D Root化パッチ 出来ました^^; | ガジェット痛信 > Android
ありがたいことに最近root化パッチが公開されたようです。
「SC-01E/SC-01D/SC-03D ROMバックアップパッチ v1」と「SC-01E Root化パッチ v1.1」をダウンロードしておきます。
バックアップ
「SC-01E/SC-01D/SC-03D ROMバックアップパッチ v1」のRunMe.batを実行して、適当に進めると、本体ストレージのbackup_dumpディレクトリにバックアップを取ってくれます。
あとはMTPでも使って、パソコンにそのファイルを移動させればおしまい。
root化
「SC-01E Root化パッチ v1.1」のRunMe.batを実行します。
無事成功したら、SuperSUとVoodoo OTA RootKeeperをマーケットよりインストールしておきましょう。
おしまい"
Credits to: yanoshi 7日前
The tablet isn't with me, so I get to take the test as soon as possible.
UpInTheAir said:
Hey Guys,
There is a separate XDA Forum for the 7.7 Plus :
http://forum.xda-developers.com/forumdisplay.php?f=1427
Click to expand...
Click to collapse
Unfortunately at this Forum is no information about Tab 7.7 Plus. I have Galaxy Tab 7.7 Plus(SC-01E) and I'm not sure it is possible to change stock ROM to any alternative one.
There are not many differences between Tab 7.7 and Plus version (only difference is: CPU and DVB-T Tuner).
It is possible that ROM for 7.7 will work in 7.7 Plus?
Here's the link Gabirumaster mentioned:
http://yanoshi.hatenablog.jp/entry/2013/05/05/014140
I managed to root my phone, thanks to the links in this tread.
If someone has problems in rooting, write here.
However, it's so easy - you download 2 files and then run them one after another... Amazing.
By the way I also would like to know whether I can flash another ROM instead of pre-installed Japanese on this device
Anyone knows?
Shinkoku said:
By the way I also would like to know whether I can flash another ROM instead of pre-installed Japanese on this device
Anyone knows?
Click to expand...
Click to collapse
You can flash another ROM if you have a custom CWM, and for this case, I was failed to insert the custom CWM. Could you install a custom CWM to your 7.7 Plus? If yes, could you give me a guide? Thanks,,
Thanks. Don't feel like flashing CWM at the moment, though. Would like to keep stock rom. But might need CWM one day, cause the SC-01E is a MOST glitchy device I ever had (and I had 3 of them before). Do not recommend anyone to buy it. Really awful device by Samsung this time, fund something else if you can, save time and nerves...
dude u found stock rom for sc-01e..mine is not booting,need to flash stock rom but cant find anywhere
SC-01E
I HAVE the same issue and would like to enable the phone on sc-01e please can anyone guide me in the right direction..?
sco1e
Shinkoku said:
Thanks. Don't feel like flashing CWM at the moment, though. Would like to keep stock rom. But might need CWM one day, cause the SC-01E is a MOST glitchy device I ever had (and I had 3 of them before). Do not recommend anyone to buy it. Really awful device by Samsung this time, fund something else if you can, save time and nerves...
Click to expand...
Click to collapse
can you help me as i am unable to use phone or root if you can you give me downloads or assit
WILLIEFRANCE said:
I HAVE the same issue and would like to enable the phone on sc-01e please can anyone guide me in the right direction..?
Click to expand...
Click to collapse
Yesterday it was my Docomo 7.7 SC-01E is I've unlocked everything. Plus, I have prepared the new cleaned rooted firmware ..
GUIDE:
1. Flash my Stock cleaned rooted multilanguage firmware UI06 with Odin 3.07 in PDA (this firmware is fresher than a uh11):
Download Stock_Rooted_SC01E_SHV_E150S_UI06
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
2. After go in recovery (you can use QuickBoot that I added in the rom) and do: wipe reset factory
Now we unlock the ability to make and receive calls: (These modems are always part of this firmware, but if you like the bootloader will not allow you to flash via Odin-we will use the terminal)
1. Put these 2 modems in internal sdcard
2. Install the terminal
3. Open the terminal, write su and press ok
4. Write this command (and press ok) :
Code:
dd of=/dev/block/mmcblk0p17 if=/sdcard/mdm.bin
5. Write this command (and press again ok):
Code:
dd of=/dev/block/mmcblk0p13 if=/sdcard/amss.bin
5. Reboot in recovery and do: wipe reset factory again
6. Turn ON your tablet, open the dialer and write: 319712358
7. Write the password: 996412
8. Go in Network Setting → Channel setting, choose: full, press: apply (The device will reboot)
9. Wipe reset factory in recovery again and enjoy:victory:
Screenshots:
View attachment 2361825
View attachment 2361826
View attachment 2361827
View attachment 2361828
View attachment 2361830
New firmware
I prepared new rooted firmware for Docomo 7.7 SC-01E from 09/08/2013
Download Stock Rooted SC01E SHV E150SKRVH09
Flash this firmware with Odin 3.07 in PDA (that you will find in the archive)
If you want to upgrade your modem, you have to use the terminal:
1. Put 2 modems, that you will find in the archive (amss.bin and mdm.bin) in internal sdcard
2. Open the terminal, write su and press ok
3. Write this command (and press ok):
Code:
dd of=/dev/block/mmcblk0p13 if=/sdcard/amss.bin
4. Write this command (and press ok again) :
Code:
dd of=/dev/block/mmcblk0p17 if=/sdcard/mdm.bin
(reboot your tablet and enjoy)
bodivas said:
I prepared new rooted firmware for Docomo 7.7 SC-01E from 09/08/2013
Download Stock Rooted SC01E SHV E150SKRVH09
Flash this firmware with Odin 3.07 in PDA (that you will find in the archive)
If you want to upgrade your modem, you have to use the terminal:
1. Put 2 modems, that you will find in the archive (amss.bin and mdm.bin) in internal sdcard
2. Open the terminal, write su and press ok
3. Write this command (and press ok):
Code:
dd of=/dev/block/mmcblk0p13 if=/sdcard/amss.bin
4. Write this command (and press ok again) :
Code:
dd of=/dev/block/mmcblk0p17 if=/sdcard/mdm.bin
(reboot your tablet and enjoy)
View attachment 2368065
Click to expand...
Click to collapse
Hi....
Thanks for your nice information.
Just want to confirm: Can I still receive the mobile TV (OneSeg TV) services with your new firmware? I noticed that there is an DMB.apk.....
Thank you.
Download mode
It seems i am a retard...I cannot access DL mode on my sc-01e it comes up with a screen in japanese something about os...i restart with power and volume down...am i stupid or is there another issue
bkh_0538 said:
Hi....
Thanks for your nice information.
Just want to confirm: Can I still receive the mobile TV (OneSeg TV) services with your new firmware? I noticed that there is an DMB.apk.....
Thank you.
Click to expand...
Click to collapse
I can not say, because in Europe does not work, you have to try (I specifically left dmb.apk)
This firmware I had to pull out from Kies ..
I uploaded full version here:
Download E150SKRVH09
WILLIEFRANCE said:
It seems i am a retard...I cannot access DL mode on my sc-01e it comes up with a screen in japanese something about os...i restart with power and volume down...am i stupid or is there another issue
Click to expand...
Click to collapse
After the 3 keys you have to press the volume up key
bodivas said:
I can not say, because in Europe does not work, you have to try (I specifically left dmb.apk)
This firmware I had to pull out from Kies ..
I uploaded full version here:
Download E150SKRVH09
After the 3 keys you have to press the volume up key
Click to expand...
Click to collapse
Hi Bro.....
Thanks for your kind reply......
If you don't mind, could you let me know what is the difference between this newest version and the previous VH09? Is the newest one rooted? Are all of them come with CMW? Or I have to install it again?
Thanks......
[SC-01F] Galaxy Note 3 (Japanese) (NTT Docomo)
Rooting information is in the second post.
Debloating and tweaking information is in the third post.
Available Firmwares:
Android 4.3 (SC01FOMUBMIF) - original firmware
Android 4.3 (SC01FOMUBNA8) - released on 2014/02/12 - patch notes
Android 4.3 (SC01FOMUBNB3) - released on 2014/03/04
Android 4.3 (SC01FOMUBNC3) - released on 2014/03/31
Android 4.4.2 (SC01FOMUBNF6) - released on 2014/07/08 patch notes
Android 4.4.2 (SC01FOMUBNI3) - released on 2014/10/16
Android 5.0 (SC01FOMUGOI4) - released on 2015/10/05 - patch notes
Download firmwares here.
Latest patch notes.
[SCL22] Galaxy Note 3 (Japanese) (au KDDI)
Original and rooted firmwares are available from Dev-Host.
Rooting information is in the second post.
Available Firmwares:
Android 4.3 (SCL22KDUBML1) - original firmware - patch notes
Android 4.3 (SCL22KDUBNB1) - released on 2014/03/04 - patch notes
Android 4.3 (SCL22KDUBND3) - released on 2014/05/15 - patch notes
Android 4.4.2 (SCL22KDU2FNF7) - released on 2014/07/09 - patch notes
Android 5.0 (SCL22KDU2GOH7) - released on 2014/09/01 - patch notes
Download firmwares here.
Rooting Information
This root method shows custom status, but FeliCa works.
Instructions - Device Rooting
There are guides on xda on how to do every step, so please don't ask how to do any particular step in this post.
If you can't get the Download Mode to show Samsung Official, keep reflashing the recovery image and rebooting. It may take a few tries.
If it doesn't work. Try making a tar file with the official recovery.img in. Guide here.
You must install the cwm in the last step using the dd command. You can't use Odin or it will disable NFC again.
Download these things:
The latest KitKat firnware (link in the first post)
The KitKat CWM recovery (attached)
Odin and Samsung Mobile Drivers
SuperSU CWM Installer
7zip
Extract the firmware so you have a tar.md5 file.
If you don't have KitKat yet, do this:
Reboot to download mode
Run Odin press AP and select the firmware tar.md5
Press Start and wait 5 minutes for your firmware to update
Reboot to download mode
Run Odin press AP and select your recovery tar file
Press Start and wait for the reboot.
Copy the SuperSU insstaller zip to your sdcard.
Reboot to recovery mode.
Install SuperSU by selecting the zip.
Reboot.
Install BusyBox Installer.
Install BusyBox. If it doesn't work, you don't have root.
Install Android Terminal Emulator
Extract recovery.img from the firmware tar.md5
Copy to /sdcard
Run this command (you can copy/paste it):
su
dd if=/sdcard/recovery.img of=dev/block/platform/msm_sdcc.1/by-name/recovery
Reboot the phone, reboot into recovery, then reboot into download mode, check that it says "Current binary: Samsung Official"
Repeat these 3 reboots until it shows official. (NFC will work then)
Extract the recovery.img from your recovery tar file to /sdcard
Run this command (you can copy/paste it):
su
dd if=/sdcard/recovery.img of=dev/block/platform/msm_sdcc.1/by-name/recoveryReboot to recovery to test that it installed.
You should now be rooted with NFC and custom recovery.
Notes:
To get to download mode: hold power+home+vol down, while the phone reboots, then at the screen with Japanese text, press vol up.
To get to recovery mode: hold power+home+vol up, while the phone rebootsp.
When using Odin, ensure re-partition is unchecked.
Instructions - TWRP
You can find an alternate recovery in this post.
Instructions - Install Xposed
Follow the rooting instructions above.
Install the Xposed Installer.
Open Xposed Installer, click Framework, click Install, reboot.
Recommended Modules:
Wanam Xposed
Instructions - Enable Bluetooth Tethering
Follow the rooting instructions above.
Follow the Xposed Installation instructions above.
Install the Xposed-Bluetooth-Tethering-Enabler module.
Open Xposed Installer, clock Modules, enable Xposed-Bluetooth-Tethering-Enabler, reboot.
Lollipop Deodex Rom
I have created a deodexed Lollipop rom for the SC-01F.
It is pre-rooted, deodexed and Busybox is installed.
You don't have to wipe and you can go back to stock easily.
NFC is working.
Please download all the files in the SC-01F folder.
Guide: (This will trip knox)
Download all the files in the SC-01F folder.
Copy "SC-01F_Part2_System.zip" to your phone's SD card.
Optional: Copy "XposedInstaller_3.0_alpha4.apk" and "xposed-v75-sdk21-arm-arter97-snapdragon_requestConcurrentGC.zip" too if you want Xposed Framework.
Reboot your phone into download mode and connect the USB cable.
Extract "Odin3_v3.10.7.zip" and run the program.
Press the "AP" button and select "SC-01F_Part1.tar"
Reboot into recovery mode.
Flash the "SC-01F_Part2_System.zip" from the SD card.
Optional: Flash "xposed-v75-sdk21-arm-arter97-snapdragon_requestConcurrentGC.zip" if you want Xposed.
Optional: Skip this step if you prefer a custom recovery over NFC.
Reboot to download mode. Flash "SC-01F_Part3_OfficialRecovery.tar"
Repeat this step until download mode shows official binary.
You may have to pull the battery and cable mid flash to trigger the official check.
You won't brick your phone from a bad recovery.img flash.
Done.
I'm a SEA Note 3 SM-N9005 user. Is there any way I can use Japanese language pack from DoCoMo version? I just switched from Xperia Z and noticed the missing language.
what are the supported bandwidth of the SC-02C model?
hmm... according to this
Code:
連続待受時間注意1注意2
（静止時） 3G：約 470時間／LTE：約 410時間／GSM：約 380時間注意6注意7
連続通話時間注意2
（音声通話時） 3G：約 1000分／GSM：約 860分
seems like only Japan frequencies
SimmoF,
Are you upgrading from the Note 2 (SC-02E)?
I still have a year to go on the SC-02E contract, I wonder if NTT Docomo offer an upgrade path?
Fulvian said:
I'm a SEA Note 3 SM-N9005 user. Is there any way I can use Japanese language pack from DoCoMo version? I just switched from Xperia Z and noticed the missing language.
Click to expand...
Click to collapse
I don't think its possible, without a huge amount of effort.
Sent from my L-06C using Tapatalk 4
AllGamer said:
what are the supported bandwidth of the SC-02C model?
hmm... according to this
Code:
連続待受時間注意1注意2
（静止時） 3G：約 470時間／LTE：約 410時間／GSM：約 380時間注意6注意7
連続通話時間注意2
（音声通話時） 3G：約 1000分／GSM：約 860分
seems like only Japan frequencies
Click to expand...
Click to collapse
SC-02C is the Galaxy S2. Did you mean SC-01F?
Docomo uses its own frequencies, but their devices support a few standard frequencies when roaming, but you won't get to full speed.
Sent from my L-06C using Tapatalk 4
Grant Barker said:
SimmoF,
Are you upgrading from the Note 2 (SC-02E)?
I still have a year to go on the SC-02E contract, I wonder if NTT Docomo offer an upgrade path?
Click to expand...
Click to collapse
I'm upgrading from the Galaxy S2.
I wouldn't upgrade, the way Docomo subsidize is by giving you a discount off your bill, every month, for 2 years. This works out to about 44000yen, if you stick the 2 years out.
Also differences aren't that great between the note 2 and 3, and they'll likely filter all the new touchwiz features into the new note 2 firmware.
Sent from my L-06C using Tapatalk 4
SimmoF said:
I'm upgrading from the Galaxy S2.
I wouldn't upgrade, the way Docomo subsidize is by giving you a discount off your bill, every month, for 2 years. This works out to about 44000yen, if you stick the 2 years out.
Also differences aren't that great between the note 2 and 3, and they'll likely filter all the new touchwiz features into the new note 2 firmware.
Sent from my L-06C using Tapatalk 4
Click to expand...
Click to collapse
Yeah. Cheers. I'll be sticking with the Note 2 which I'm very happy with.
I just upgraded from my American Note 2 (Verizon) I was using with a Docomo SIM. I'm loving it so far, but I know it could be much better if I had root (to remove bloatware, change a few things, add a few things, etc). I will post links in here if I confirm root methods and recoveries that work with this device.
Sent from my SC-01F using xda app-developers app
gaxiolafm said:
I just upgraded from my American Note 2 (Verizon) I was using with a Docomo SIM. I'm loving it so far, but I know it could be much better if I had root (to remove bloatware, change a few things, add a few things, etc). I will post links in here if I confirm root methods and recoveries that work with this device.
Sent from my SC-01F using xda app-developers app
Click to expand...
Click to collapse
Great. So the De la Vega method requires the firmware dump to be available for the hacker to make it for our firmware.
So I wouldn't use that until one is available for our device. I will tell him as soon as I can.
SimmoF said:
Note: Do NOT do any updates until we know how to root this thing. Updating may block your chances of rooting.
Edit: I just saw that the Root de la Vega requires a custom version for our AP and CSC, so I will go down to the Docomo shop today and get the details, and request a custom root for us. I will post the details here when done.
Click to expand...
Click to collapse
I will be watching this page constantly waiting for an update! I just picked up my note an hour ago. Thanks for making the effort!
AllGamer said:
hmm... according to this
Code:
連続待受時間注意1注意2
（静止時） 3G：約 470時間／LTE：約 410時間／GSM：約 380時間注意6注意7
連続通話時間注意2
（音声通話時） 3G：約 1000分／GSM：約 860分
seems like only Japan frequencies
Click to expand...
Click to collapse
What you are quoting here are not frequencies, but standby and talk time ratings.
Standby 470 hours on 3G and so on.
Talk time 1000 minutes on 3G and so on.
But it seems that you are right about the fequencies either way.
look here: http://www.samsung.com/jp/consumer/mobilephone/galaxy-note/docomo/SM-N900DZKEDCM-spec
SimmoF said:
Hello everyone,
Some of you may know me for my work in the SC-02C thread.
I am starting this device thread for the users of the Japanese Galaxy Note 3.
I intend to pick up one of these on release day, October 17, so I'll post as much advice and information as I can about rooting/modding.
I will try rooting using the Root de la Vega method, as soon as I get the device.
Note: Do NOT do any updates until we know how to root this thing. Updating may block your chances of rooting.
Edit: I just saw that the Root de la Vega requires a custom version for our AP and CSC, so I will go down to the Docomo shop today and get the details, and request a custom root for us. I will post the details here when done.
You can visit the Official Docomo Page for this device.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Click to expand...
Click to collapse
Just got my Galaxy Note 3 from Docomo Shinyokohama branch last night.
This page is great and thank you to you sir for your technical knowledge and continued support for Samsung device owners here in Japan.
My previous phone was a Galaxy S2 (SC-02c) and I used your previous methods on rooting and now, my phone is still perfectly working
Though I'm still hesitant to tinker with my (20 hour-old) Galaxy Note 3...but I will continue to monitor this thread.
Thanks again in advance!
no one buying the galaxy J? :laugh::laugh:
docomo Note 3 owner now. Sweet root method please....(Onegaishimas)
tried ODIN with CF-Auto-Root-hlte-hltexx-smn9005 end status said PASS but on root check - failed.
Any pointers. Need CHAINFIRE to run.
n9005
I've purchased N9005 version off of hong kong based website. With my galaxy s3 from docomo sim card, i don't get any 3G/4G.... nothing but makeing and receiving phone calls.... i can't even send text!!!! but i can receive one... what is going on!
any help?
soul870518 said:
I've purchased N9005 version off of hong kong based website. With my galaxy s3 from docomo sim card, i don't get any 3G/4G.... nothing but makeing and receiving phone calls.... i can't even send text!!!! but i can receive one... what is going on!
any help?
Click to expand...
Click to collapse
Firstly, you need to set up the APN.
Secondly, DoCoMo has IMEI filtering on sp-mode, so you must be using a DoCoMo branded device.
You will need to switch your data plan from sp-mode to mopera to use your own device.
http://www.mopera.net/service/about/fit.html
Sent from my SC-01F using Tapatalk
I'm new to Japan and my original Note is getting long in the tooth so I'm considering buying a DoCoMo Note, hence I'm curious about bloatware. My understanding is that Japanese operators jam their phones with cute but useless apps, I also believe they only come with support for Japanese and English languages and you are not able to download support for other languages, is that true?
Is there any advantage to getting a DoCoMo device over Au?
Sent from my GT-N5110 using Tapatalk 4
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
This method will, when completed, will provide you with root and an unlocked bootloader, with fastboot available. It is a somewhat involved process, but the majority of the process has been simplified as much as possible.
WARNING!!!!This replaces your current bootloader with a debug bootloader. If you attempt to lock this bootloader you may brick your device.
Currently AT&T(H910) and Sprint(LS997) cannot return to stock because no KDZ files are available.
Disclaimer:
Once your phone is unlocked, it will no longer be covered by LG warranty @me2151.
As we cannot guarantee the proper operation of our hardware with custom software, we are not able to maintain the full scope of warranty for your device after you have unlocked the bootloader.
Because of that we have a responsibility to let you know that defects which may result from, or were caused by custom device-software may not be covered by LG warranty @me2151.
LG @me2151 can no longer guarantee the full functionality of your device after you unlock the bootloader. Unlocking your device may cause unexpected side effects that may include but are not limited to the following:
***Your device may stop working.
***Certain features and functionalities may be disabled.*
***Your device may become unsafe to the point of causing you harm.
***Your device becomes physically damaged due to overheating.
***The behavior of your device may be altered.
***Some content on your device may no longer be accessible or playable due to invalid DRM keys.*
***All your user data, settings, and accounts may disappear. (Therefore, we recommend that*you*backup all your data).
** -*Software updates delivered via LG FOTA (Firmware Over the Air) or Web Download services may not work on your device anymore.
LG @me2151 will not be responsible for the damages caused by any*custom software being flashed to your phone.
Known Issues:
AM&FM Radio no longer works
Boot time higher
No way to revert to stock(LS997/H910)
Possible overdose of root awesomeness!
Maybe more. Let us know!
Links:
- v20-root.zip
- TWRP
- Terminal Emulator
- Newest SuperSU(SuperSU v2.78 SR5 or greater is needed)
-Stock LS997 rom. for Sprint users only. (Fix's numerous problems)
Pre-requisites:
- ADB and fastboot setup and Installed
- Terminal Emulator installed onto the phone.
- The above links downloaded and SuperSU placed on the SD Card.
Working Devices:
- Verizon (VS995)
- Sprint (LS997)
- ATT (H910)
- Korean(F800L)
Note: International Variants (E.g.H990DS) May get supported in the future, but are currently being worked on at the moment. If you attempt to use this method on Unsupported Devices(any V20 not listed in working devices) then you are in uncharted territory. It will almost definitely brick your device. YOU HAVE BEEN WARNED!!!!
This will tutorial will be broken up into 2 sections, during the second section the instructions will differ depending on the variant of the phone you are using.
- Unlocking the Bootloader:
1) Copy all the files from inside the "Required Files" (Inside the unzipped "v20-root" folder) and paste it into your active ADB directory. Then copy and paste twrp-3.0.2-1-us996.img to your active ADB directory.
2) If you currently don't have Terminal Emulator then go and download and install now.
3) Plug your device into the computer and verify ADB is working. Then;
On Windows, double-click "RUNMEFIRST.bat, DO NOT CLOSE THE LOG WINDOW THAT OPENS, then double-click "Step1.bat"
On Linux/MacOS ("#" Signifies a comment below)
Code:
./RUNMEFIRST.sh
# OR
bash ./RUNMEFIRST.sh
Open a Separate Terminal next to the RUNMEFIRST terminal, then type:
Code:
./Step1.sh
# OR
bash ./Step1.sh
When you run The sh or Bat files there will be a Permission denied error on 2 files: Flatland and Flatland64. This is normal and nothing to worry about.
3.5) Wait for a shell prompt, then type (or copy):
Code:
run-as con
chmod 0777 /storage/emulated/0/*
4) Open Up Terminal Emulator
Type:
Code:
id
Check if context is "Untrusted_app"
If "Untrusted_app" is displayed, Continue:
Type into Terminal Emulator:
Code:
applypatch /system/bin/atd /storage/emulated/0/dirtysanta
If it doesn't show up as "Untrusted_app", repeat the above steps from Number 1
5) Watch the RUNMEFIRST dialog for when it tells you to run Step2. Then;
On Windows, double-click "Step2.bat"
On Linux/MacOS, type:
Code:
./Step2.sh
# OR
Bash ./Step2.sh
Once step 2 is completed, you'll be in bootloader, procced to "Flashing TWRP" section to continue.
Note/Warning: Verizon Users Vibrator will be constantly going off, until the whole process is complete (Past Android Setup Wizard).
- Flashing TWRP and Fixing Varient Issues:
1) Run Step3, so TWRP can be flashed and a working boot.img flashed (Fix's screen problem) by;
On Windows, double-click "Step3.bat"
On Linux/MacOS, type:
Code:
./Step3.sh
# OR
Bash ./Step3.sh
******Sidenote******
If you get message saying <waiting for device> on Step3.bat then you do not have the fastboot drivers installed(you may have the program but not the drivers).
To fix: Go to your device manager while the device is connected in fasboot and right click the item that says Android and select update drivers. Then select from internet. and let it install the drivers then try step3.bat again.
*************
2) After you're rebooted, and back at the main lockscreen, type;
Code:
adb reboot recovery
Your device will reboot to an LG screen. Keep checking adb devices for your device.
Then type:
Code:
adb reboot recovery
***********
Device should display a red triangle and say corrupt, then it will boot into TWRP.
3)Once in TWRP, Press Cancel on the password prompt and then swipe to allow system modifications.
Note:If you wish to make a back up now, you MUST save it to your SD card, and you cannot backup the data partition.
After the backup is complete, return to the main menu and hit wipe then select ?Format Data?, and follow the instructions there.
4) Steps below will differ, depending on what model you have, choose the correct model and follow its method.
- Verizon(VS995) and ATT(H910):
4.1) Flash SuperSU.zip
4.2) Go back to Main-menu > Wipe > [Format Data] > Type ?Yes?
4.3) Go back to Wipe > Advanced > Check Dalvik, Data and Cache > Slide to wipe
4.4) Go back to Main-menu > Reboot > System
- Sprint(LS997):
4.1) Go to Wipe > Advanced > Check Dalvik, System, Data and Cache > Slide to wipe
4.2) Go back to Wipe > [Format Data] > Type ?Yes?
4.3) Go back to Main menu > Install > LS997 Stock Rom then Flash SuperSU.zip
4.4) Go back to Main-menu > Reboot > System(you will get static on boot. this is normal)
4.5) Sprint users are Done at this point. You do not need anything else. Everything will work except static on boot.Note:Any following Instructions are for all devices again.
5) During reboot you will get a Red Triangle with a "!" inside, this is normal (First boot after flashing SuperSu will show the Red triangle twice.Wait for system to boot (this will take awhile). It may appear like the system has frozen but it has not. JUST WAIT!
*****VERIZON USERS******
It has come to my attention that some users have encountered abnormally long first boot time(over 20 minutes before first time setup)
To resolve this issue:
Boot into bootloader by pulling the battery and reinserting it and holding VOL- and phugging in the phone. then typing:
Code:
fastboot flash boot bootbackup.img
fastboot reboot
**************
*****ALL USERS*****
If you encounter a "Secure Boot" Password then booting the first time you did not Format data properly.
To reiterate: To properly decrypt the device you need to boot into TWRP and go to WIPE->FORMAT DATA and you will be prompted to type "yes" to format and decrypt.
**************
Once you are booted and have proceeded through the setup wizard, re-enable Android Debugging (ADB) if not already enabled.
Type:
Code:
adb reboot bootloader
6) Once inside bootloader, Type:
Code:
fastboot flash boot bootbackup.img
When it says finished, Type:
Code:
fastboot reboot
The device will boot back into system.
WARNING:This is a required step for non sprint users, it prevents background crashes and fix's battery drain. If you do NOT follow this then the device will have bad battery life, be laggy and crashes will occur regularly.
7) Once full booted back into android, Type;
Code:
adb reboot recovery
8) Once TWRP loads, Then;
- Flash SuperSU.zip
- Go back to Wipe > Advanced > Check Dalvik and Cache > Slide to wipe
- Go back to Main-menu > Reboot > System
You now should have a rooted LG v20, download your favorite root checker app and verify root.
Note:For a root app to work, it will have to support Systemless root.
Contributers/Developers:
@me2151(General)
@glitschi667(General)
@EMSpilot(Debug device) #3
@elliwigy(Ideas and testing) #5
@Matt07211(Formatting this awesome guide and helping out with general stuffs)#4
@1619415(Awesome Santa Pic at the top!)#8
Alright guys. Its time for some fixes!!!
For our known issues:
Comfort view, youtube, boot time and possibly radio.
All fixed by flashing the AT&T H918 Konverged Kernel.
Keep in mind this is a temporary fix until I get a full custom kernel made for our devices(or at least a way to make the screen work out of box that we can use on other kernel sources).
To use this kernel on our phones you need to download the zip, Place on sd card, reboot to twrp, install the zip, wipe dalvik/cache then reboot.
You WILL GET STATIC ON EVERY REBOOT!
After the phone is booted put the screen to sleep by pressing the power button and cover your proximity sensor(so your 2nd screen turns off) then turn your screen back on. Your screen will work until reboot. If you reboot you will have the static again. Just follow the steps I just listed above to get the screen working again.
--------
Other Updates.
I believe I have finally found a way to revert sprint devices sprint devices to unrooted stock. I will be testing the method on my phone in the next couple days.
WooHoo!!!! I bricked attempting to revert!
So heres an update for you guys. Reverting has been confirmed possible using KDZ files for your specific models. Confirmed working for KDZs are H915, VS995 and some others. I do Have a new v20. I am going to pull the stock sprint files tomorrow and see what I can do about making that work.
Nicely done Guys.
@me2151(General)
@glitschi667(General)
@elliwigy(Ideas and testing)
@Matt07211(Formatting this awesome guide and helping out with general stuffs)
@1619415(Awesome Santa Pic at the top!)
I am extremely happy that the V20 User Debug I invested in worked out!
Enjoy everyone!!
Cheers
Reserved
Reserved lol
Awesome work guys!
Sent from my LG-LS997 using Tapatalk
reserved
---------- Post added at 04:51 PM ---------- Previous post was at 04:51 PM ----------
pdaddy said:
Awesome work guys!
Sent from my LG-LS997 using Tapatalk
Click to expand...
Click to collapse
****
Good job @me2151 !!!:good::good::good:
Awesome! Now all the fun can begin!
Thanks for all your hard wprk on getting us root!
Thanks,
Chaz187
Sent from my LG-LS997 using Tapatalk
So awesome to hear, you guys are amazing. Its possible the dev with the h915 is waiting for the firmware update (we're told in time for the holidays?!) that would enable LTE on wind to see if this still applies. Nevertheless, thanks, i dont remember the last time i read so much. Lol
Sent from my LG-H915 using Tapatalk
Ooo Santa you so dirty.. Can't wait to do this
Sent from my VS995 using Tapatalk
SHABBA JOTS said:
So awesome to hear, you guys are amazing. Its possible the dev with the h915 is waiting for the firmware update (we're told in time for the holidays?!) that would enable LTE on wind to see if this still applies. Nevertheless, thanks, i dont remember the last time i read so much. Lol
Sent from my LG-H915 using Tapatalk
Click to expand...
Click to collapse
From the last I hear from him. The bootloader unlocks and twrp installs BUT he has no service(he is Rogers) So he is looking into all that.
AWESOME job, everyone! Thanks so much for this-- I admit I may wait a little while for feedback before trying my own unit, but given that I jumped on the V20 early in hopes that if any version is hacked it'll be the earliest firmwares, I can't imagine it'll be too long before I'm back to enjoying my phone the way I like it!
Definitely will be sending some coffee money along, even though I wasn't in any of the bounties...
Damn I've been waiting for this soooo much but there's only thing. I don't now crap about LG phones I've been a Sammy fanboy for 7 years lol. Guess I'll have to wait till my boy can do it.
Sent from my LG-LS997 using Tapatalk
---------- Post added at 08:13 PM ---------- Previous post was at 08:06 PM ----------
EMSpilot said:
Nicely done Guys.
@me2151(General)
@glitschi667(General)
@elliwigy(Ideas and testing)
I am extremely happy that the V20 User Debug I invested in worked out!
Enjoy everyone!!
Cheers
Click to expand...
Click to collapse
And thank you for purchasing that expensive out of pocket device.
Sent from my LG-LS997 using Tapatalk
Subutek said:
Damn I've been waiting for this soooo much but there's only thing. I don't now crap about LG phones I've been a Sammy fanboy for 7 years lol. Guess I'll have to wait till my boy can do it.
Sent from my LG-LS997 using Tapatalk
---------- Post added at 08:13 PM ---------- Previous post was at 08:06 PM ----------
And thank you for purchasing that expensive out of pocket device.
Click to expand...
Click to collapse
to be honest theres nothing really lg specific besides the files themselves lol.. of course you never use Odin outside of Samsung lol..
majority of it is pc bat or adb commands and then you got your typical twrp stuff but hey, best to have your buddy do it if youre not comfortable
Hey guys I need a little help, last step I was able to complete was running "Step3.sh, after reboot I'm unable to get into recovery mode. does anyone know the manual steps to get to recovery mode?
I also continue to get the popup "com.android.phone" has stopped.
No mobile service
hoopsdavis said:
Hey guys I need a little help, last step I was able to complete was running "Step3.sh, after reboot I'm unable to get into recovery mode. does anyone know the manual steps to get to recovery mode?
Click to expand...
Click to collapse
I'm assuming you're on Mac/Linux. If so, in terminal verify connection with "adb devices". If you're connected fine, enter "adb reboot recovery"
I started but wouldn't get any feedback when I would double RUNMEFIRST or Step 1.... I don't know if windows 10 matters.
I'll try again a little later tonight.
My device was connected and found; adb devices
oh yeah, im also running minimal adb and fastboot.
http://forum.xda-developers.com/showthread.php?t=2317790
Thank you guys for the hard work. So happy to have hotspot working.
dc.wash95 said:
I'm assuming you're on Mac/Linux. If so, in terminal verify connection with "adb devices". If you're connected fine, enter "adb reboot recovery"
Click to expand...
Click to collapse
I'm actually on windows
hoopsdavis said:
I'm actually on windows
Click to expand...
Click to collapse
Well in that case, you probably should have executed the ".bat" not the ".sh"
I'm running Windows 10, and successfully followed the guide. My device is past boot currently, and is installing apps from a Google backup.
This tool is out of date. See the main R9S thread for an updated tool by Wu Xianlin which gives you an improved TWRP recovery and access to more ROMs.
Original post is below for historical purposes only.
Oppo R9S (Chinese version) TWRP installation tool
Only works on Chinese OS release 005 which can be downloaded here and flashed in stock recovery.
Earlier versions will not work, nor will later versions. It has to be this specific version.
P̶r̶o̶b̶a̶b̶l̶y̶ doesn't work on international editions either.
DOWNLOAD - R9S_TWRP.zip - V1.01
DOWNLOAD - R9S_TWRP.zip - V1.0
Changelog
1.01 - Tweaked timings to try and improve success rate
1.01 - Changed how text is output to hopefully improve appearance on Windows 7
This script uses an exploit by Chinese developer Wu Xianlin to gain temp root, then it flashes his TWRP build that works on the R9S despite the locked bootloader.
From there you can attempt to perma-root your phone, install a custom ROM etc. etc.
Thanks to the following XDA members, without whom this would not have been possible:
jacksmack
celoxocis
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Antivirus issues
Some AV's may complain about this file containing a Trojan. They are technically correct. It's called "dirtycow" and is being used in the wild to hack into Linux systems. It cannot affect Windows systems, but I use it to hack a linux-based system (your phone)
If your AV refuses to let my script run you will have to disable it temporarily. Feel free to read through my script (root1.bat) to check what it is doing.
Useful things to flash in TWRP
CyanogenMod13 - by Wu Xianlin
Stock Recovery - by Wu Xianlin
GApps (ARM64) - by opengapps.org
Updated basebands, ripped from ColorOS
Use these only if you have issues with phone/GPS/etc. after installing CM. Otherwise leave alone.
[2017-01-11 v0180] - released ROM (China) - by me!
[2017-01-24 v1470] - ALPHA ROM (China) - by me!
Note: The version number on basebands stays the same, but the MD5s are different. No idea what has changed, but they work!
Unbrick instructions:
Does not work in Windows 10. Tested working in Windows 7
Download this unbrick package
Install the quallcommmtkdriver package
Run daanav-enabler as administrator
Run msmdownloadtool as administrator
Click through any timeout error you get
Click on the titlebar of MSMDownloadTool and press F6 to enable the options
Fully power down your phone by holding vol-, vol+ and power for 10 seconds
Hold vol- and vol+ while connecting the USB cable (use the stock Oppo cable)
MSM should now show your phone.
Press F5 to decide what to flash. For the first attempt choose "All except userdata".
Click the start button.
After 5 minutes your phone should reboot into ColorOS.
If ColorOS hangs on boot, then repeat the above staps and this time flash all, including userdata. This will wipe your photos etc. sorry!
This will leave you on V004 of the OS. You will need to upgrade to 005 before attempting to root again.
Can I request a version of this that stops at permanent rooting? Unless you think there would be a problem with the fact that I intend on using it on a r9s plus.
Or a link to what I maybe overlooked, in case it already exists.
Unfortunately this program doesn't perma-root. It gains a temp root and uses that to flash TWRP. TWRP can then be used to flash a custom ROM or a rooting tool.
It also doesn't unlock the bootloader. Wu Xianlin somehow managed to make a version of TWRP that the locked bootloader is happy with!
however if you edit root1.bat and scroll down to line 181. Change it from:
Code:
type root3.txt | adb shell /data/local/tmp/root2.sh
to:
Code:
adb shell /data/local/tmp/root2.sh
Then the script will just drop you to a root shell. Unfortunately you are then on your own as to how you get perma-root.
I have no idea whether this method will work on the R9SPlus. In theory it should do but I've not tried it. I won't be held responsible if you brick your phone and probably won't be able to help, though you should be able to do a three-finger reboot and then boot into recovery and reflash ColorOS.
Optional modifications you can make that will make the script neater:
You can also remove lines 178 and 179
Code:
echo Copying TWRP
adb push r9s-twrp-3.0.2.0-20170107.img /sdcard/twrp.img
and change line 184 from
Code:
pause
REM ---- CHINESE TWRP HELP ----
to
Code:
pause
exit
REM ---- CHINESE TWRP HELP ----
I will take your "I have no idea if this will work fo r9s+" at face value and try to be patient for something more certain, thanks for your contribution nonetheless
I saw the translation you posted and am a bit depressed Wu recommended to return the phone...
Oppo make amazing hardware but terrible software that is never updated. I used to be ok with this because they actively encouraged rooting and custom ROMs but this change in attitude from them makes it very hard to recommend the phone.
I would be interested to know if this exploit does gain root on the Plus. In theory it should work, and there's also a decent chance that TWRP will too as the hardware is very similar, but will require someone very brave/stupid to try it
BTW. Anyone who is going to try this on the Plus. Ensure you have a flashable .ozip of a working ColorOS (full install, not OTA) saved to internal storage as the stock Oppo recovery is a POS that doesn't provide ADB, MTP or USB.
If you end up wrecking your OS and don't have that image in place ready to flash from recovery you are screwed.
Likewise do not flash TWRP until you are sure that your OS is still bootable, and also take a dump of the stock recovery first! (and post it in the other thread as it's bloody useful to have!)
Sent from my OPPO R9s using XDA Labs
Hi the Unbrick pack RAR is corrupted and can not unzip.
Also there is Trojan in DOWNLOAD - R9S_TWRP.zip - V1.0 - Dirtycow file and the NOD Antivirus is deleting this file.
Please advice how to proceed ?
NOD is correctly detecting that this is a hacking tool using a well known exploit (dirtycow).
Since you actually want to do that, you're going to have to disable NOD until you're done.
Sent from my OPPO R9s using XDA Labs
Lum_UK said:
NOD is correctly detecting that this is a hacking tool using a well known exploit (dirtycow).
Since you actually want to do that, you're going to have to disable NOD until you're done.
Sent from my OPPO R9s using XDA Labs
Click to expand...
Click to collapse
Hi I got to somewhere but I am stuck now...
Please check the pic and advice how to install the CyangenMode. (I have uploaded the pic in your thread in Oppo Community forum please check it there because I am new here and can not post with external links..)
Sorry for the inconvenience. Looks like I am few steps away to finish the job but something is missing...
Goro1234’s image: http://s27.postimg.org/8usudi9g3/IMG_20170207_133854.jpg
You need to do a wipe data/cache/dalvik as CM won't install on top of incompatible data.
Note that this will wipe your installed apps, settings, app data, saved games etc. but will not wipe your photos, music, downloads or anything else saved to internal storage.
You may wish to take a backup from within TWRP first. Apps like Titanium Backup and Nandroid Manager are reasonably good at restoring apps and data from a TWRP backup.
Also don't forget to install GApps
Sent from my OPPO R9s using XDA Labs
For the unbrick package you need 7-Zip to extract it.
Lum_UK said:
`Also don't forget to install GAaps`
Hi I am on Cyanogen now !!! Thanks for the help. Can you please tell me now which is the correct gapps version for our device. I have installed random one which does not make connection with google. I have tried to install ARM 64, but cant flash because systems says that is incompatible... Thanks
Click to expand...
Click to collapse
Select ARM64, android 6.0 and whichever variant you like (I recommend the Pico version)
Sent from my OPPO R9s using XDA Labs
Sorry for the English, I made a mess with the phone, after unlocking everything, and held the phone for several days with CM13, I saw that GPS was not working, so vovelo return to the origin, but now I can not installing Stock Recovery more to put the stock rom, I tried to do unbrick, but when I press start of msmdownloadtool, the program stops and closes. If some kind soul gives me some advice. Done everything under win 7 reset. Thank you so much Gianfranco.
GPS should be working. I'm using it all the time on CM13 as my phone is my satnav.
Maybe wipe and reflash, or try one of the baseband updates?
Sent from my OPPO R9s using XDA Labs
Now, the problem is more to do so that I can not leave,
I installed through the files Stock TWRP Recovery as a boot, and I hand the boot source and installing the original rom, after the reboot remains on oppo screen. what can I do. Thank you so much Gianfranco.
hold all three buttons for 10 seconds to forceibly power off the phone and then try to boot to recovery.
If you get the Oppo recovery then try to do a factory reset and then flash the stock ROM,
if you get TWRP then try to flash Cyanogen.
If you can't do either then you're going to have to run the unbrick tool. Do you have another PC you can try it on?
Thanks, but I have tried various solutions, when I install the boot ROM from stock, is successful, the reboot hangs installation applications. I wanted to know if you can other software for unlocking. Thank you very much for giving me some advice, thanks ancora.Gianfranco.