Hi ,
I am new to the forum and recently started using custom roms..
I was installing the "rayne rom" using cwm and after formatting data and system..it stopped suddenly and gave a message "symlink failed"
Now the phone does not reboot to CWM recovery and only the previous Devs boot logo comes...PLEASE help...I think i may have bricked it.
@abhi007 said:
Hi ,
I am new to the forum and recently started using custom roms..
I was installing the "rayne rom" using cwm and after formatting data and system..it stopped suddenly and gave a message "symlink failed"
Now the phone does not reboot to CWM recovery and only the previous Devs boot logo comes...PLEASE help...I think i may have bricked it.
Click to expand...
Click to collapse
Are you pressing the recovery buttons correctly? Take out battery then put it back. Then try pressing the Power button and Volume Up + Down together and see if it opens CWM..
ibshar said:
Are you pressing the recovery buttons correctly? Take out battery then put it back. Then try pressing the Power button and Volume Up + Down together and see if it opens CWM..
Click to expand...
Click to collapse
Thanks for the reply..
Yes the CWM recovery came...but i do not have stock Rom in phone and my mem card slot is busted..
Should i try flashing using SP flash tools ???
@abhi007 said:
Thanks for the reply..
Yes the CWM recovery came...but i do not have stock Rom in phone and my mem card slot is busted..
Should i try flashing using SP flash tools ???
Click to expand...
Click to collapse
Then you need to flash the stock ROM with SP Flash tool
@abhi007 said:
Thanks for the reply..
Yes the CWM recovery came...but i do not have stock Rom in phone and my mem card slot is busted..
Should i try flashing using SP flash tools ???
Click to expand...
Click to collapse
Yes..u can flash through SP tool as said by @IBashar..in case..if u dont want to flash through SP tools..I will suggest u to use someone else SD card & paste ur rom in that & then flash through recovery..as I personally feel that flashing through SP Tool is quite cumbursome..
HIT THANKS IF I HELPED U
Sent from my JMP V13 using xda app-developers app
@abhi007 said:
Hi ,
I am new to the forum and recently started using custom roms..
I was installing the "rayne rom" using cwm and after formatting data and system..it stopped suddenly and gave a message "symlink failed"
Now the phone does not reboot to CWM recovery and only the previous Devs boot logo comes...PLEASE help...I think i may have bricked it.
Click to expand...
Click to collapse
Don't worry bro! Try to boot into CWM again because it should be there. Then try to flash the ROM again...
And remember, in future, always take a Nandroid backup before you install anything, mod or ROM. It really helps in case something goes wrong and phone stops working,
ibshar said:
Then you need to flash the stock ROM with SP Flash tool
Click to expand...
Click to collapse
Hey,
I tried flashing using SP tools but it is coming USB device not recognized.(i have installed the drivers in my pc)..... is there any other tool to recover my phone?
Since SP tools does not recognize the device.. it stays at 0%...
Any suggestion is welcome...pls..
@abhi007 said:
Hey,
I tried flashing using SP tools but it is coming USB device not recognized.(i have installed the drivers in my pc)..... is there any other tool to recover my phone?
Since SP tools does not recognize the device.. it stays at 0%...
Any suggestion is welcome...pls..
Click to expand...
Click to collapse
None of the tools will work unless you install the correct Drivers.. So install teh drivers that are given in the SP Flash tool thread and then try.
@abhi007 said:
Hey,
I tried flashing using SP tools but it is coming USB device not recognized.(i have installed the drivers in my pc)..... is there any other tool to recover my phone?
Since SP tools does not recognize the device.. it stays at 0%...
Any suggestion is welcome...pls..
Click to expand...
Click to collapse
I Also Face The Problem With SP Tools 0% Problem Take Out The USB Cable And Insert It Again And After 30-40 Seconds It Will Show The Process Completed 100% And Green Ring Will Be There
Sent from my Micromax A110 (Canvas 2) using xda premium
@abhi007 said:
Hey,
I tried flashing using SP tools but it is coming USB device not recognized.(i have installed the drivers in my pc)..... is there any other tool to recover my phone?
Since SP tools does not recognize the device.. it stays at 0%...
Any suggestion is welcome...pls..
Click to expand...
Click to collapse
see the video below
non of the driver is working, my phone keeps disappearing on device manager it is hard bricked. i installed one custom rom from xda and after rebooting system it is not at all responding either to charging and not to recovery opption also please help bro
Related
Yes!!!!!!!!! Flash/Unbrick Your Xolo A700
(PLEASE FOLLOW INSTRUCTIONS CAREFULLY,I AM NOT RESPONSIBLE IF YOU TURN IT INTO A PAPERWEIGHT)
Firstly Download Firmware And Tools From This Link
Things Needed
Bricked Xolo A700
Usb Cable
Windows Pc
And A Calm Head
Instructions
Click Here For Youtube Tutorial
Remove Battery From Your Phone And Re-insert It
Connect Your Phone To Pc With Usb Cable
Your PC Will Prompt You To Install The Usb Drivers
Go To-Device Manager>Ports>MTK 65xx Preloader
And Do A Right Click On It>Update Driver>Browse My Computer For Driver(Something Like That)
Select The Driver Folder Where You've Extracted All The Files From The ZIP And Follow The Setup
After Installing Remove Your Phone From PC
Remove And Re-Insert The Battery
Open SP Flash Tool
Click On Scatter Loading
Navigate To The Folder Where You've Extracted The Stock Rom Folder
Select MT6577 Scatter .txt
Click On Download Button>Click On Yes
Connect Your Phone And Wait Till The Process Is Complete
Voila!!!!!!!!!!!!!!!!!!!!!!!!!!
You.................Yes You've Done It
For Those Who Are Facing Black Screen After Flashing
Hit Format-Download Button Instead Of Pressing Download
And Everything Will Be FIne:highfive::highfive:
Need Help
I am getting a continuous restart after the logo appears, I think I have deleted the recovery as it does not goes into recovery also, keeps on restarting, let me know if this method will help me to unbrick my device..
safetydell said:
I am getting a continuous restart after the logo appears, I think I have deleted the recovery as it does not goes into recovery also, keeps on restarting, let me know if this method will help me to unbrick my device..
Click to expand...
Click to collapse
ys you can recover it with help of the above tut
yasirmujtaba said:
ys you can recover it with help of the above tut
Click to expand...
Click to collapse
Thanks, I am out of station as of now, will go home by Saturday, I will surely try this method, hope it helps me to recover my device..
The download link to "firmware and Tools " is not working.
Edit: It is Working now.
Help Needed
yasirmujtaba said:
ys you can recover it with help of the above tut
Click to expand...
Click to collapse
No Luck dude, I did the same as you said but after everything it showed download complete and I started my phone, it came to logo " XOLO " and after that blank screen waited a lot but still the same blank screen, any help from you pls...
sorry for replying late
then you can hit format-download in sp flash tool
it will work for sure
Sent from my Xolo A700 using xda premium
yasirmujtaba said:
sorry for replying late
then you can hit format-download in sp flash tool
it will work for sure
Sent from my Xolo A700 using xda premium
Click to expand...
Click to collapse
Thanks everything went well and was able to get the recovery back but not the stock, booted in CWM recovery and installed your xtrance rom as i was not able to boot the stock rom, it was idle in the boot and was not booting also, anyways thanks now now device is unbricked..
safetydell said:
Thanks everything went well and was able to get the recovery back but not the stock, booted in CWM recovery and installed your xtrance rom as i was not able to boot the stock rom, it was idle in the boot and was not booting also, anyways thanks now now device is unbricked..
Click to expand...
Click to collapse
which option you chose for format I chose "Automatic and format whole flash except bootloader and nav bin something"
it goes dead not even XOLO logo but when chose download it shows xolo logo and then blank
need urgent help
i formatted entiree flash and now sp tool doesnt detect my phone. please help me out.
Install the drivers agin and use diff usb cable
Sent from my IQ446 Magic using xda premium
actually now the phone is not recognized as a phone. but unknown device by the computer. the computer doesnt accept the ini files as drivers saying unknown driver. i m in a pickle now. i tried changing the usb cable still nothing. i think my preloader is also formatted. can u help me in flashing the preloader back?
Didn't try FORMAT
I used the tools to unbrick my xolo a700 struck at bootloop. But no luck. its still the same. WHAT DO U SUGGEST???
Struck at XOLO logo after XOLO animation
I given factory Reset and the bricked.
I tried the procedure after that my xolo mobile struck at XOLO logo after XOLO animation...
Please help....!!!
guys please help us by posting some tried and tested step by step procedure. My Xolo A700s is stuck on boot loop. even i flashed original rom . but dont know what to do with the update file provided along with the rom. guys help
jash2711 said:
actually now the phone is not recognized as a phone. but unknown device by the computer. the computer doesnt accept the ini files as drivers saying unknown driver. i m in a pickle now. i tried changing the usb cable still nothing. i think my preloader is also formatted. can u help me in flashing the preloader back?
Click to expand...
Click to collapse
What did you do? I think I have a similar issue with my tablet, a Pixi 8079.
please help me to unbrick my xolo a500
it is in a soft brick and dont have cwm recovery installed
all stared when tried to install the driver of chainfire 3d
what can i do
Have u tried enter the emergency mode?
Sent from my WT19i using xda premium
ur phone has which cpu??? mence mtk or other??
Its was foolish of you to install cf3D when its clearly says no ics support
Well you can flash cwm using fastboot method and flash your stock rom
sent from my super advanced mini fridge
Do u have ur mobile model stock rom??
Sent from my Micromax A116 using xda premium
daviyankee said:
please help me to unbrick my xolo a500
it is in a soft brick and dont have cwm recovery installed
all stared when tried to install the driver of chainfire 3d
what can i do
Click to expand...
Click to collapse
Download Stock/ custom rom for XOLO A500 (Search In google or XDA )
Download CWM Recovery
Place Rom in memory card
Remove and install battery press vol up then press power key to get bootloader mode
flash this CWM recovery then flash rom through CWM
A500 Not booting
professor_proton said:
Its was foolish of you to install cf3D when its clearly says no ics support
Well you can flash cwm using fastboot method and flash your stock rom
sent from my super advanced mini fridge
Click to expand...
Click to collapse
I installed auto swapper script from some post, and now my cell is not booting,
i have download stock rom but it does not have scatter.txt, i have SP flash tool and drives and all things.
even i have download blu dash4.0 but its not completing, error message update failed.
please help me to install stock rom please
i do not know how to flash with SP flash tool,
so please provide me steps
sonujain10 said:
I installed auto swapper script from some post, and now my cell is not booting,
i have download stock rom but it does not have scatter.txt, i have SP flash tool and drives and all things.
even i have download blu dash4.0 but its not completing, error message update failed.
please help me to install stock rom please
i do not know how to flash with SP flash tool,
so please provide me steps
Click to expand...
Click to collapse
download cwm recovery from here https://www.dropbox.com/s/h3w1doejuh3ecq4/cwm_a500.img
flash using fastboot (bootloader)
reboot to recovery
cwm 6 will be there
flash stock rom
Xolo q500 softbricked
Can Anyone Help me. My Xolo Q500 is softbricked. It is niether booting normally nor booting to recovery menu. I have tried sp flash tools but the stock rom of my phone which i downloaded does not contain any scatter file, probably because it is a Qualcomm based device. Please help me..................
xolo q500 dead after formatted
sir please help me i do have the same problem
xolo q 500 i soft bricked using format while connect in the smart upgared tool
i tried to flash but its ask disk to be formatted i am unaware of it so i mistakenly formatted now the phone is not getting turn on
or in the recovery mode please help or tell me the procedure
I just tried to do a factory reset from the settings application but my phone went into a bootloop. It keeps on rebooting into CWM. I tried to flash the srock 4.1.1 through spflash tool but my phone goes into a boot loop immediately. I tried to flash it with batteries taken out but my phone was repeatedly connected and disconnected from my PC. I can't even charge my phone. I was using "SLT-Nexus-TSUNAMI™ TechVanced™ By SuperDroid-BOND™".... Guys someone please help me.....:crying::crying::crying::crying::crying:
If U r not able To flash Via Spflash too
you flash stock roms via Spflash tool Or From Recovery
press Thx If This Helped You Need More Help
Sent from my A110 using Tapatalk
SMARTY BOY said:
If U r not able To flash Via Spflash too
you flash stock roms via Spflash tool Or From Recovery
press Thx If This Helped You Need More Help
Sent from my A110 using Tapatalk
Click to expand...
Click to collapse
I cant boot my phone even into the recovery mode that's my problem.
Bricked XOLO Q3000 (Once Again)
Bricked my XOLO Q3000 Kitkat while trying to install PhilZ custom recovery.Now its stuck in boot loop(the XOLO logo keeps appearing again and again).I backed up the stock boot.img and recovery.img through FlashifyI even tried installing stock recovery through mtk droid tools but to no avail.Now what to do??
SOLVED
No matter how much you brick your phone,there is a mode called Factory Mode.Open it by holding vol down key+ Power .Then select format emmc and DONE.So I've become quite of an engineer ..
Haldar_dhruv said:
No matter how much you brick your phone,there is a mode called Factory Mode.Open it by holding vol down key+ Power .Then select format emmc and DONE.So I've become quite of an engineer ..
Click to expand...
Click to collapse
How u flashed the philz recovery??
There is no way u can brick ur deivce while flashing recovery if u follow the methods given here.
U can always press the thanks button if ur using any stuff of any dev.
Formatting emmc means formatting ur internal storage too.
ur all data on internal storage will be gone
Bricked Again
This time it happened when I was editing the build.prop .I saved the file as I had the original build.prop file backed up.Then I thought I should restore it.I copied the build.prop file from my sdcard and overwrited it to /system .But now its again struck in boot loop.I just need access to the phone storage so that I can try to replace it again.What should I do???
help help help... avi
i flashed twrp 2.8.0.0, then tried installing hny15 8/1/2015 rom but installation failed , then flashed philz recovery through twrp then reboot but stucked on xolo boot logo. trying to go to recovery but xolo logo flashes again n again, what to do now brother. HELP..! PLZZZZZzzzz,..
:crying:
Xolo Q3000 stuck in Boot Loop
Haldar_dhruv said:
No matter how much you brick your phone,there is a mode called Factory Mode.Open it by holding vol down key+ Power .Then select format emmc and DONE.So I've become quite of an engineer ..
Click to expand...
Click to collapse
Hi,
I tried to flash the twrp custom recovery via a flash tool on my device post which the device got stuck in boot loop. Now when i am trying to flash the recovery or even trying to install stock rom nothing is working the device does get recognized on any pc or laptop in spite of the drivers being there... i am new to all this would really appreciate your help in fixing this.
Su007 said:
Hi,
I tried to flash the twrp custom recovery via a flash tool on my device post which the device got stuck in boot loop. Now when i am trying to flash the recovery or even trying to install stock rom nothing is working the device does get recognized on any pc or laptop in spite of the drivers being there... i am new to all this would really appreciate your help in fixing this.
Click to expand...
Click to collapse
Solution : Visit http://forum.xda-developers.com/show...74&postcount=1
"This method is useful for warranty purposes and also for UNBRICKING !!!!
U can revert back to normal rom from any possible bad situations like soft brick or hard brick.
Also u can enjoy ur stock rom.
U will need sp flash tools and flash files."
SEE THE CATEGORY : INSTALL STOCK FIRMWARE
download the flash files and follow the guide
Ask avi3230 as I am not that much experienced,He helped me
GauravBak said:
i flashed twrp 2.8.0.0, then tried installing hny15 8/1/2015 rom but installation failed , then flashed philz recovery through twrp then reboot but stucked on xolo boot logo. trying to go to recovery but xolo logo flashes again n again, what to do now brother. HELP..! PLZZZZZzzzz,..
:crying:
Click to expand...
Click to collapse
Solution : Visit http://forum.xda-developers.com/showpost.php?p=55599274&postcount=1
"This method is useful for warranty purposes and also for UNBRICKING !!!!
U can revert back to normal rom from any possible bad situations like soft brick or hard brick.
Also u can enjoy ur stock rom.
U will need sp flash tools and flash files."
SEE THE CATEGORY : INSTALL STOCK FIRMWARE
download the flash files and follow the guide
Ask avi3230 as I am not that much experienced,He helped me :cyclops:
The Most Important Page
Before u do anything with your beloved XOLO Q3000 visit and bookmark this link http://forum.xda-developers.com/showpost.php?p=55599274&postcount=1
If problem solved hit the Thanks button
Haldar_dhruv said:
This time it happened when I was editing the build.prop .I saved the file as I had the original build.prop file backed up.Then I thought I should restore it.I copied the build.prop file from my sdcard and overwrited it to /system .But now its again struck in boot loop.I just need access to the phone storage so that I can try to replace it again.What should I do???
Click to expand...
Click to collapse
try too flash again the original roms via stock recovery..
Haldar_dhruv said:
Bricked my XOLO Q3000 Kitkat while trying to install PhilZ custom recovery.Now its stuck in boot loop(the XOLO logo keeps appearing again and again).I backed up the stock boot.img and recovery.img through FlashifyI even tried installing stock recovery through mtk droid tools but to no avail.Now what to do??
Click to expand...
Click to collapse
Try flashing the ctr recovery! use flashify and flash either the zip file or the img file! This should work
worked for me
MIUI ROM Woooooo
Yes I have already solved this post Thanks anyway
EAGERLY WAITING FOR MIUI rom to be uplaoded today by avi
KEEP CHECKING HERE http://forum.xda-developers.com/showpost.php?p=55599274&postcount=1
rashr..
Haldar_dhruv said:
Bricked my XOLO Q3000 Kitkat while trying to install PhilZ custom recovery.Now its stuck in boot loop(the XOLO logo keeps appearing again and again).I backed up the stock boot.img and recovery.img through FlashifyI even tried installing stock recovery through mtk droid tools but to no avail.Now what to do??
Click to expand...
Click to collapse
try to flash recovery.img via rashr... It shoul work for u.
mujaid714 said:
try to flash recovery.img via rashr... It shoul work for u.
Click to expand...
Click to collapse
Thanks But the Problem was already solved, would make some sense for others maybe.
Thanks For Helping
Haldar_dhruv said:
Before u do anything with your beloved XOLO Q3000 visit and bookmark this link http://forum.xda-developers.com/showpost.php?p=55599274&postcount=1
If problem solved hit the Thanks button
Click to expand...
Click to collapse
Hi Haldar,
Can you please guide me through step by step please, I am very new to all these. To try anything, My xolo q3000 is stuck in bootloop and is not getting detected on any PC or even turning on to get it flashed to any software.
Any help would be greatly appreciated.
Thanks
alfamine
alfamine said:
Hi Haldar,
Can you please guide me through step by step please, I am very new to all these. To try anything, My xolo q3000 is stuck in bootloop and is not getting detected on any PC or even turning on to get it flashed to any software.
Any help would be greatly appreciated.
Thanks
alfamine
Click to expand...
Click to collapse
Tell me in detail whatever happened. Try the below procedure also.
No matter how much you brick your phone,there is a mode called Factory Mode.Open it by holding vol down key+ Power .Then select format emmc and DONE
Haldar_dhruv said:
Tell me in detail whatever happened. Try the below procedure also.
No matter how much you brick your phone,there is a mode called Factory Mode.Open it by holding vol down key+ Power .Then select format emmc and DONE
Click to expand...
Click to collapse
I tried to flash to a recovery.img through flashify application and now bricked my phone which is in bootloop now and is neither booting to use other softwares or methods neither is it getting detected on any PCs to flash custom recovery.
I have tried to Volume down + power button and also Volume up + power button to get into recovery menus but none to success,
Just stuck at boot logo of xolo.
Thanks
alfamine
Go to this link here
http://forum.xda-developers.com/q3000/development/xolo-q3000-one-ultimate-thread-t3038259
Then click on unbricking, install adb drivers in pc etc and continue as it says.
Hello My Q-3000 is getting stuck in the boot loop(XOLO Logo ) . Even though I am used Vol+ & power not getting recovery menu ,but odin with red triangle.Please help to solve this problem. I requesting experts to guide me to resolve this issue.
Use Sp flash tool to install stock ROM & u should check ultimate thread
Use Sp flash tool to install stock ROM & u should check ultimate thread
Dear Mr.Sachin Fulzule, thanks for reply I did all that ,but problem is my Phone is not going into recovery mode by pressing VOl+ and Power butten suck in the boot loop XOLO logo is appearing. Please help me
VIKRAM CHINCHOLKAR
vmc809 said:
Dear Mr.Sachin Fulzule, thanks for reply I did all that ,but problem is my Phone is not going into recovery mode by pressing VOl+ and Power butten suck in the boot loop XOLO logo is appearing. Please help me
VIKRAM CHINCHOLKAR
Click to expand...
Click to collapse
If u have pc, then download sp flash tool, stock from for Xolo q3000, drivers for q3000, then install drivers properly & flash it phone using sp flash tool, no need to go to recovery.
sachin.r.fulzele said:
If u have pc, then download sp flash tool, stock from for Xolo q3000, drivers for q3000, then install drivers properly & flash it phone using sp flash tool, no need to go to recovery.
Click to expand...
Click to collapse
Dear Mr. Sachin Fulzule, namaskar I did already what you mentioned, but problem is not solved.Please give some other solution. Waiting for your help.
No more suggestions, submit phone to Xolo care
Sent from my HM NOTE 1W_MIUI6_5.7.23
vmc809 said:
Dear Mr. Sachin Fulzule, namaskar I did already what you mentioned, but problem is not solved.Please give some other solution. Waiting for your help.
Click to expand...
Click to collapse
Have u followed the procedure mentioned in this post.
04 - Flashing stock ROM using SP flash tools
Unbricking guide.
If u did exactly same then the phone should boot normally.
Also check the battery charging, maybe its not sufficiently charged.
avi3230 said:
Have u followed the procedure mentioned in this post.
Click to expand...
Click to collapse
I've told him, the same earlier, but he replied that he had done it, still no success.
Sent from HM NOTE 1W_MIUI6_5.8.6
Even i too faced the same problem..but managed to flash by sp tools..make sure ur ports are working and drivers are properly installed..and downloaded file is not corrupted..
mujaid714 said:
Even i too faced the same problem..but managed to flash by sp tools..make sure ur ports are working and drivers are properly installed..and downloaded file is not corrupted..
Click to expand...
Click to collapse
It's because u should either install vcom drivers or cynus drivers for xolo q3000, availability of both causing the trouble.
Sent from HM NOTE 1W_MIUI6_5.8.6