I commented that from one day to the other my phone stopped responding while booted and my logo appears Telephony (CLARO ARGENTINA) keeps the samsung logo and does not start over. The tests were to raise the custom recovery, but does not start the screen stays black, so I decided to install nuevamante, but throws the following error:
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
and leave it there for about 1 hour and nothing.
I said well you reinstall the system 0, from the unbranded of course, but throws the following:
<ID:0/005> Added!! <OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300UBDLJ2_I9300UBDLI2_I9300UVCDLJ1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> boot.img
<ID:0/005> NAND Write Start!!
<ID:0/005> recovery.img
<ID:0/005> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
The issue is that the light equipment, ie load the logo of the company, and the samsung logo stays long.
The thing is that I load the cwm, there cyanogem install any rom or another by. Tar.md5 than the original?
another that occurred to me is whether it is possible to install the CMW from a Micro SD, and lift the OS from there!
Just probe with CWM-Recovery-LTE-SGS3-v5.tar.md5, pass and shoot, but do not lift the CWM
*
*
Added <ID:0/007>!
<OSM> Enter CS for MD5 ..
<OSM> Check MD5 .. Do not unplug the cord ..
<OSM> Please wait ..
<OSM> CWM-Recovery-LTE-SGS3-v5.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully ..
<OSM> Leave CS ..
<ID:0/007> Odin v.3 engine (ID: 7) ..
<ID:0/007> File analysis ..
<ID:0/007> SetupConnection ..
<ID:0/007> Initialzation ..
<ID:0/007> Get PIT for mapping ..
<ID:0/007> Firmware update start ..
<ID:0/007> recovery.img
<ID:0/007> NAND Write Start!!
RQT_CLOSE <ID:0/007>!
RES <ID:0/007> OK!!
Removed <ID:0/007>!
Remain <ID:0/007> Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
Exactly, only between DW mode, then to not enter recovery mode, but the strange thing is that the phone starts but is labeled in the samsung logo.
Also try to get into safe mode by pressing the home, but does not start the key vibration.
It's a case sooo weird.
*
Thanks for everything!
Related
tried to flash cm9 on i9100G running ics.
odin flash keeps failing and the phone doesnt go past the samsung start screen.
keep getting
"<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> cm-9-20120420-ODIN-galaxys2.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> zImage
<ID:0/005> NAND Write Start!!
<ID:0/005> Sbl.bin
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)"
on odin....
what am I supposed to do?
p.s:tried a new pit file too... didnt work....
Hello so im stuck in TWRP recovery with no rom and no backup. If i try to flash a rom thru TWRP it FAILS.
Please help me how to restore my tablet to stock.
Its Galaxy Note 10.1 from VERIZON (SCH-i925)
Thank you
Btw it started with me trying to flash Cyanogen Mod (That is shared on this forum) And it failed, too bad i did a wipe before trying to install, i hoped everything is gonna go well..
BUMP Please help, really urgent im stuck in odin, i downloaded some software for sch-i925 and i chosen phone, not PDA in odin, and i even made it worse as im experiencing blinking screen and only mode is odin, if i try to reflash it by selecting PDA, it fails.
Code:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> KIES_HOME_I925VRAMK1_I925VZWAMK1_1481643_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Removed!!
<ID:0/004> Can't open the serial(COM) port.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> boot.img
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
exjuno said:
BUMP Please help, really urgent im stuck in odin, i downloaded some software for sch-i925 and i chosen phone, not PDA in odin, and i even made it worse as im experiencing blinking screen and only mode is odin, if i try to reflash it by selecting PDA, it fails.
Code:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> KIES_HOME_I925VRAMK1_I925VZWAMK1_1481643_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Removed!!
<ID:0/004> Can't open the serial(COM) port.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> boot.img
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Close the antivirus and the Kies through the task manager
And then?
exjuno said:
And then?
Click to expand...
Click to collapse
Then Odin flash again with stock rom for your device.
Idk whats going on I used the odin3 download stock firmware to try to restore the phone after boot loop I tried to install TWRP custom recovery it didnt reboot into and so i tried to restore through odin3 and stock frimware and it says failed. Any ideas thanks
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G920TUVU1AOCG_G920TTMB1AOCG_G920TUVU1AOCG_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
make sure re-partition is unchecked from the options tab.
Sent from my SM-G920I using Tapatalk
Try :
1. Using a different USB cable or USB port.
2. Redownload again your ROM as download errors can cause flash failures.
3. Lastly, consider bringing your S6 back to Samsung for warranty repair. Its free within your warranty period.
I hope this helps.
Hi, I recently fixed my note edge by installing 4.4 kitkat. A few days later I realized it was really slow and so I plugged it in and tried to flash marshmallow stock. This didn't work and now my phone goes automatically to download mode and every time I try to re-flash it it either insta fails or says aboot fused 2 binary 1. Also, I think i got twrp installed because it passed on odin but if I try to boot recovery it Says "Could not do normal boot and ddi: mmc_read failed". Thanks for the help!
https://forum.xda-developers.com/note-4-tmobile/general/ddi-mmcread-failed-boot-error-fix-t3434335
Bordo_Bereli51 said:
https://forum.xda-developers.com/note-4-tmobile/general/ddi-mmcread-failed-boot-error-fix-t3434335
Click to expand...
Click to collapse
Thanks for the link but the files included in the guide are listed for the note 4 so how do I use that in note edge thanks for help
UPDATE
I have got phone into download/ odin mode but still need help as my flash fails in odin\
<ID:0/007> Added!!
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> aboot.mbn
<ID:0/007> NAND Write Start!!
<ID:0/007> sbl1.mbn
<ID:0/007> rpm.mbn
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/007> Removed!!
Same thing...
Here's my odin log.
<ID:0/008> Added!!
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Set PIT file..
<ID:0/008> DO NOT TURN OFF TARGET!!
<ID:0/008> Get PIT for mapping..
<ID:0/008>
<ID:0/008> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/008> Removed!!
P.s I have the AT&T model.
UPDATE
<ID:0/008> Added!!
<ID:0/008> Removed!!
<ID:0/008> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BL_N915AUCS2DQD1_CL8932341_QB13132575_REV00_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> AP_N915AUCS2DQD1_CL8932341_QB13132575_REV00_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CP_N915AUCS2DQD1_CL8932341_QB13132575_REV00_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_ATT_N915AATT2DQD1_CL8932341_QB13132575_REV00_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Set PIT file..
<ID:0/008> DO NOT TURN OFF TARGET!!
<ID:0/008> Get PIT for mapping..
<ID:0/008> Firmware update start..
<ID:0/008> aboot.mbn
<ID:0/008> NAND Write Start!!
<ID:0/008> sbl1.mbn
<ID:0/008> rpm.mbn
<ID:0/008> tz.mbn
<ID:0/008> sdi.mbn
<ID:0/008> NON-HLOS.bin
<ID:0/008> boot.img
<ID:0/008> recovery.img
<ID:0/008> system.img.ext4
<ID:0/008> FAIL! (Write)
<OSM> All threads completed. (succeed 0 / failed 1)
It failed half way through on the phone it says
"ODIN : flash write failure"
1) ODIN 3.09
2) Get N915A 5.0.1 Modem
3) Get N915A 6.0.1 Firmware Stock (the AP file)
4) Get N915A 6.0.1 Modem
1)Place phone in DOWNLOAD MODE (volume down + home + power button)
2) Open ODIN 3.09
3) Place file N915A 5.0.1 Modem in CP
4) Place file N915A 6.0.1 Firmware.tar in AP box
5) Once ODIN is finished flashing the files power off your phone and go back into DOWNLOAD MODE, dont boot.
6) Place file N915A 6.0.1 Modem in CP box
7) Once the file is flashed your phone will be mmc error free and you will have a 100% working phone again.
thejug786 said:
Hi, I recently fixed my note edge by installing 4.4 kitkat. A few days later I realized it was really slow and so I plugged it in and tried to flash marshmallow stock. This didn't work and now my phone goes automatically to download mode and every time I try to re-flash it it either insta fails or says aboot fused 2 binary 1. Also, I think i got twrp installed because it passed on odin but if I try to boot recovery it Says "Could not do normal boot and ddi: mmc_read failed". Thanks for the help!
Click to expand...
Click to collapse
Tell me, how could you return to 4.4.4? I also have n915a on marshmallow, but I would like to return to kitkate. Tell me how you did it ??
"A few days later I realized it was really slow" tells us maybe that this is a emmc failure problem
https://www.sammobile.com/forum/showthread.php?t=30686
In this forum, this guy has the same problem like you. He tried different attempts. Even though he flashed succesfully and booted up, his phone was very slow and had freezing problem. A while later he got again the "Could not do normal boot and ddi: mmc_read failed" problem.
Hi,
I was wondering if someone could assist me on the issue im having. First i tried rooting Samsung gt-s7275b and failed completely and got stuck in odin mode, Then i tried downloading the stock firmware using this site samsung-firmware.org/es/download/Galaxy__Ace__3__LTE__-South__America-__/0963/COM/S7275BUBUAMJ2/S7275BUWAAMK1/ and extracted when i try to upload it thought pda on version 3.07 i get fail, then i tried 3.12.7 and i get unsupported dev on the phone. Now im not sure if what i download is the correct firmware. Not sure what to do
This is the error
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> S7275BUBUAMJ2_S7275BUWAAMK1_S7275BUBUAMJ2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> boot.img
<ID:0/005> NAND Write Start!!
<ID:0/005> cache.img.ext4
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Thank you