hi all
I'm out of luck to revive my bricked hTC magic 32a since one painful month but 2oday i wanted to try if my computer will recognize it or not having a blinking orange led (meaning no battery) i tried to connect it and suddenly my device manager detected an unknown device what should we do now install it's driver? from the sdk or what
Try to: download and install HTC Sync
why only one reply
hi guys
why there is only one reply couldn't this be our only hope ? without the need for a serial cable or a jtag cable ?
did you try install the htc sync as he suggest? cause then you get your driver installed
lets us know if you did and what happend
I tried to downgrade the kitkat version because I couldn't update my apps, using a flash tool.
It then shut down and now does not turn on at all. When I plug into the computer the USB gets into a cycle/loop of connect and disconnect. Please help me if you have the time.
lenover9000 said:
I tried to downgrade the kitkat version because I couldn't update my apps, using a flash tool.
It then shut down and now does not turn on at all. When I plug into the computer the USB gets into a cycle/loop of connect and disconnect. Please help me if you have the time.
Click to expand...
Click to collapse
Does it vibrates or display anything?
Tyaginator said:
Does it vibrates or display anything?
Click to expand...
Click to collapse
no. But I think it goes on '''META MODE'" ONLY on the computer for a few seconds.
Thanks for commenting.
Check device manager in your pc when you connect your phone, is it showing MTK 65xx preloader
Tyaginator said:
Check device manager in your pc when you connect your phone, is it showing MTK 65xx preloader
Click to expand...
Click to collapse
It shows Mediatek preloader usb vcom port (com7) alternating with mtk usb port (com6).
lenover9000 said:
It shows Mediatek preloader usb vcom port (com7) alternating with mtk usb port (com6).
Click to expand...
Click to collapse
U must have flashed some other device's firmware and which guide u have followed
Tyaginator said:
U must have flashed some other device's firmware and which guide u have followed
Click to expand...
Click to collapse
I used this one.
forums (dot) lenovo (dot) com/t5/A-and-P-Series/Lenovo-A536-stuck-during-firmware-upgrade/td-p/1744571[/url]
I downloaded the latest firmware from
"THIS is the latest original ROW firmware (PC Flash Tool installation)"
This whole guide was fine, it worked for me.
But the problem was when I tried to downgrade the firmware to an older version.
I tried to replace the lastest official firmware with this one ROM Android 4.4.2 (older official needrom(dot)com/download/lenovo-a536/
sorry can't link websites yet
http://forum.xda-developers.com/showthread.php?t=1943442
Try this thread
Tyaginator said:
http://forum.xda-developers.com/showthread.php?t=1943442
Try this thread
Click to expand...
Click to collapse
Thank you so much for staying with me to solve this problem. The phone is fixed.
I followed the
"
For MT6575/ 77
With the battery out, hold the volume up, don't let go & plug in the USB cable will activate META mode for few seconds...Typically, you need to click Download at SP Flash Tool before entering META mode or it will auto disconnected...
"
except I downloaded the lenovo a536 stock rom.
the only thing I did different was that I plugged in (META MODE) and THEN pressed download or else the usb would never be detected (they both show different COM numerals.)
After that I firmly held the whole usb into the phone during the whole flashing, or else it might get automatically disconnected again.
Then I updated/upgraded to the latest firmware, And it is all optimal. :good:
THANKS AGAIN !!!
lenover9000 said:
Thank you so much for staying with me to solve this problem. The phone is fixed.
I followed the
"
For MT6575/ 77
With the battery out, hold the volume up, don't let go & plug in the USB cable will activate META mode for few seconds...Typically, you need to click Download at SP Flash Tool before entering META mode or it will auto disconnected...
"
except I downloaded the lenovo a536 stock rom.
the only thing I did different was that I plugged in (META MODE) and THEN pressed download or else the usb would never be detected (they both show different COM numerals.)
After that I firmly held the whole usb into the phone during the whole flashing, or else it might get automatically disconnected again.
Then I updated/upgraded to the latest firmware, And it is all optimal. :good:
THANKS AGAIN !!!
Click to expand...
Click to collapse
Glad it's fixed
I Too Need help my lenovo a536 is bricked
My phone is not booting , unable to install USB VCOM Drivers and it is constantly going off while installing and unable to install driver ,phone vibrates shows logo but it goes in bootloop pls help urgent:crying:
prathamsd4 said:
My phone is not booting , unable to install USB VCOM Drivers and it is constantly going off while installing and unable to install driver ,phone vibrates shows logo but it goes in bootloop pls help urgent:crying:
Click to expand...
Click to collapse
What do u mean by "it is constantly going off while installing"
Does it boot in recovery mode? Please be as specific as you can while posting questions.
Sent from a Device using an App!
Tyaginator said:
What do u mean by "it is constantly going off while installing"
Does it boot in recovery mode? Please be as specific as you can while posting questions.
Sent from a Device using an App!
Click to expand...
Click to collapse
it does not boot in recovery mode,
while trying to install mediatek usb vcom drivers phone constantly connects and disconnect and i am unable to install drivers..
prathamsd4 said:
it does not boot in recovery mode,
while trying to install mediatek usb vcom drivers phone constantly connects and disconnect and i am unable to install drivers..
Click to expand...
Click to collapse
I don't think you need to connect phone during installing drivers and phone will stay connected after properly installing DA Vcom drivers
Sent from a Device using an App!
I have similar problem
Hi, please I need your help. I tried to flash stock ROM but I hard bricked my phone. When I connect phone with computer I'm holding volume up button. In device manager it shows "MediaTek USB Port (COM4)" but after three seconds it disconnect. This is why I can't flash ROM. It's everytime disconnect after three seconds.. Please help me.
Lenovo A536
Please help me guys, where is GND and COLO point of lenovo a536
same problem
i have a lenovo a536 and when i flash the stock
it goes to a cycle of off and on , help me to fix this
ive tried a lot of stock roms i searched,and none of them worked , the cycle of turning off and on is still there
Hi i rooted acer s57 (mtk 6752 as it says) and after offical update it was soft bricked and then i downloaded spft and i flashed preloader and all other stuffs (Acer_AV0K0_S57_1.007.00_EMEA_GEN1) and i got hard bricked only blue light when i connect it via usb to pc or charger i tried to flash again (Acer_AV0K0_S57_1.003.00_EMEA_CUS1) got ERROR 4032 : Enable DRAM failed and i cant format it or even flash preloader or anything.. my pc doesnot even recgonize phone until i hold volume button down and connect it then i get unknown device and i dont know what to do...
maybe its something with drivers.. if anyone has solution...
thanks
bgveric1 said:
Hi i rooted acer s57 (mtk 6752 as it says) and after offical update it was soft bricked and then i downloaded spft and i flashed preloader and all other stuffs (Acer_AV0K0_S57_1.007.00_EMEA_GEN1) and i got hard bricked only blue light when i connect it via usb to pc or charger i tried to flash again (Acer_AV0K0_S57_1.003.00_EMEA_CUS1) got ERROR 4032 : Enable DRAM failed and i cant format it or even flash preloader or anything.. my pc doesnot even recgonize phone until i hold volume button down and connect it then i get unknown device and i dont know what to do...
maybe its something with drivers.. if anyone has solution...
thanks
Click to expand...
Click to collapse
Hello,
Please try posting your query here Ask any Query Newbie Friendly with all relevant details, the experts there maybe able to assist you.
-Vatsal
Hello everyone,
I have a problem with my Galaxy S6.It is stuck on Samsung logo screen and won't turn on.Also,my phone isnt recognized by any computer.I tried a lot of USB cables,a lot of computers,i installed the drivers,tried with kies,kies 3(drivers included),Smart Switch with automatic driver instalation,tried everything and my S6 is still not recognized by pc.I cant turn on my phone to activate usb debugging or something and i cant install a custom rom or a official rom?What can i do to fix my phone?is it another way to fix the logo screen stuck without connecting the phone to a computer?tried installing a rom , but it says "external blablabla is deactivated" or something like this
iuliflr said:
Hello everyone,
I have a problem with my Galaxy S6.It is stuck on Samsung logo screen and won't turn on.Also,my phone isnt recognized by any computer.I tried a lot of USB cables,a lot of computers,i installed the drivers,tried with kies,kies 3(drivers included),Smart Switch with automatic driver instalation,tried everything and my S6 is still not recognized by pc.I cant turn on my phone to activate usb debugging or something and i cant install a custom rom or a official rom?What can i do to fix my phone?is it another way to fix the logo screen stuck without connecting the phone to a computer?tried installing a rom , but it says "external blablabla is deactivated" or something like this
Click to expand...
Click to collapse
Greetings and welcome to assist. Did you do anything to your phone before the bootloop? Also if you put your phone in download mode is it recognised in kies/smartswitch emergnecy firmware recovery ?
Regards
Sawdoctor
Tried to unroot the phone before.The USB/charging port is broken,fast charghing isnt working anymore,thats why the phone isnt recognized at all.I will change the broken piece then it should be recognized by pc and i can reinstall the android.also'the motherboard can be damaged.anyway,the phone quality is very bad,i had a lot of problems with it,ill never buy a Samsung again.
Hey,
I got a Tcl m3g wich i root and flash to CM12. After a mounth my phone wasn't able to boot, it was stuck in a bootloop. So i flashed it with QFIL and it was still stuck in a bootloop with primo V2 firmware so i flashed it a second time with an other firmware. My phone wasn't stuck anymore in a bootloop but still won't boot.When i connected it to my computer it apears like an hard drive.But the next day when i conneced it to my computer it apears "unknow device" i tried t download qualcom driver to use fastboot but it seems to not work my device is still "unknow device" in device manager (i can't access any mode and my screen is black + my batterry is dead). I hope one of you can hep me:fingers-crossed:
Sorry for my bad english
Update:The computer doesn't detect my phone :'(, the unknow device was my mice...