Related
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Note: Before I proceed with this part, Samsung has made it VERY EASY for new users to flash compared to the older ones, Unlike the previous version's that require you to flash it twice or such, or separate files, Their newer releases will always be in this format. With one PDA.md5 file. Unfortunately I cannot keep updating this thread with every region as the flashing methods are exactly the same as follows.
1. Firstly, Download the required firmware from here
2. Run Odin3 v3.04 at the bottom of the page.
3. Set your phone to download mode : Press Volume down + OK first, then hold Power button.
4. Connect your phone, you should see Odin shows your phone is Added with COM number.
5. Extract the contents from the zip, You should have a .dll and a 200-300 MB PDA file.
6. At this point you should see Re-Partition, Auto Reboot and F. Reset Time unchecked.
7. Click PDA button and select the only PDA file in the zip folder (Here you should not touch any of the Re-Partition/F.Reset options as the newer Odin automatically selects it for you, how conveinient!)
8. Click Start button to flash these files to phone.
9. Do not touch anything till you see PASS on the program window.
10. Once you have flashed, after the phone started up, press *#1234# and check your PDA,Phone and CSC, everything should be there. (There should not be any "Unavailable")
11. Factory reset and enjoy
Note: XXKPQ can only be flashed with help from it's supporting predecessor XXKPE like the XXKPN/XXKPH/XXKPM series, So make sure you have XXKPE downloaded. User flashing version varies with this, but this is my successful 100% assured boot.
Note: For those of you receiving WiFi drop issues, Assign a static IP using
Static IP [Download Here], hit the advanced tab and let it auto configure. Credit to [thatguyonfacebookiforgot]
1. Firstly, Download the 2.3.6 firmware from Przekret's thread
2. Run Odin3 v1.83
3. Set your phone to download mode : Press Volume down + OK first, then hold Power button.
4. Connect your phone, you should see Odin shows your phone is Added with COM number.
5. Click PIT button and select this file: latona_20110114.pit
6. You should see Re-Partition, Auto Reboot and F. Reset Time checked.
7. Click PDA button and select this file: CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar
8. Click PHONE button and select this file: MODEM_I9003XXKPE_REV_00_CL1041909.tar
9. Click BOOTLOADER button and select this file: APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar
10. Click CSC button and select this file: GT-I9003-CSC-MULTI-OXAKPE.tar
11. Click Start button to flash these files to phone.
12. Do not touch anything till you see PASS on the program window.
13. Turn off the phone and set it back into download mode once you get an initial first boot to homescreen. Do not set up anything, Just power off and set to download mode.
Note: You only need to flash once to XXKPE before proceeding to XXKPQ
14. In Odin, press Reset button. Re-partition should be unchecked automatically.
15. Select file I9003XXKPQ_I9003XXKPQ_I9003SERKPQ_HOME.tar.md5 as PDA
16. Click on Start to flash XXKPQ PDA to phone
17. Once you have flashed, after the phone started up, press *#1234# and check your PDA,Phone and CSC, everything should ended with KPQ
18. Factory reset and enjoy
Note: XXKPN can only be flashed with help from it's supporting predecessor XXKPE like the XXKPH/XXKPM series, So make sure you have XXKPE downloaded. User flashing version varies with this, but this is my successful 100% assured boot. This firmware is to fix the issues that pertained and caused some WiFi issues for other's
1. Firstly, Download the 2.3.5 firmware from Przekret's thread
2. Run Odin3 v1.83
3. Set your phone to download mode : Press Volume down + OK first, then hold Power button.
4. Connect your phone, you should see Odin shows your phone is Added with COM number.
5. Click PIT button and select this file: latona_20110114.pit
6. You should see Re-Partition, Auto Reboot and F. Reset Time checked.
7. Click PDA button and select this file: CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar
8. Click PHONE button and select this file: MODEM_I9003XXKPE_REV_00_CL1041909.tar
9. Click BOOTLOADER button and select this file: APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar
10. Click CSC button and select this file: GT-I9003-CSC-MULTI-OXAKPE.tar
11. Click Start button to flash these files to phone.
12. Do not touch anything till you see PASS on the program window.
13. Turn off the phone and set it back into download mode once you get an initial first boot to homescreen. Do not set up anything, Just power off and set to download mode.
Note: You only need to flash once to XXKPE before proceeding to XXKPN
14. In Odin, press Reset button. Re-partition should be unchecked automatically.
15. Select file I9003XXKPN_I9003XXKPN_I9003SERKPN_HOME.tar.md5 as PDA
16. Click on Start to flash XXKPN PDA to phone
17. Once you have flashed, after the phone started up, press *#1234# and check your PDA,Phone and CSC, everything should ended with KPN
18. Factory reset and enjoy
Note: XXKPM can only be flashed with help from it's supporting predecessor XXKPE like the XXKPH series, So make sure you have XXKPE downloaded. User flashing version varies with this, but this is my successful 100% assured boot.
1. Firstly, Download the 2.3.5 firmware from Przekret's thread
2. Run Odin3 v1.83
3. Set your phone to download mode : Press Volume down + OK first, then hold Power button.
4. Connect your phone, you should see Odin shows your phone is Added with COM number.
5. Click PIT button and select this file: latona_20110114.pit
6. You should see Re-Partition, Auto Reboot and F. Reset Time checked.
7. Click PDA button and select this file: CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar
8. Click PHONE button and select this file: MODEM_I9003XXKPE_REV_00_CL1041909.tar
9. Click BOOTLOADER button and select this file: APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar
10. Click CSC button and select this file: GT-I9003-CSC-MULTI-OXAKPE.tar
11. Click Start button to flash these files to phone.
12. Do not touch anything till you see PASS on the program window.
13. Turn off the phone and set it back into download mode once you get an initial first boot to homescreen. Do not set up anything, Just power off and set to download mode.
Note: You only need to flash once to XXKPE before proceeding to XXKPM
14. In Odin, press Reset button. Re-partition should be unchecked automatically.
15. Select file I9003XXKPM_I9003XXKPM_I9003SERKPM_HOME.tar.md5 as PDA
16. Click on Start to flash XXKPM PDA to phone
17. Once you have flashed, after the phone started up, press *#1234# and check your PDA,Phone and CSC, everything should ended with KPM
18. Factory reset and enjoy
From Custom ROM's [Must be GINGERBREAD, Not Froyo, I am not responsible if your phone ends in a bootloop from ignorance]:
1. Just flash I9003XXKPM_I9003XXKPM_I9003SERKPM_HOME.tar.md5 in PDA as usual.
2. The phone will end up in a bootloop due to ext4 conversion, Proceed to step 3.
3. Flash Skin's CFRoot in respective PDA.
4. Boot into Custom Recovery via 3 Button Combo.
5. Select option's Wipe Cache and Factory Reset
6. Voila, Enjoy your new easy flashable method.
Note: XXKPH can only be flashed with help from it's supporting predecessor XXKPE, So make sure you have XXKPE downloaded. User flashing version varies with this, but this is my successful 100% assured boot.
1. Firstly, Download the link from spacebar's XXKPH Feedback thread.
2. Run Odin3 v1.83
3. Set your phone to download mode : Press Volume down + OK first, then hold Power button.
4. Connect your phone, you should see Odin shows your phone is Added with COM number.
5. Click PIT button and select this file: latona_20110114.pit
6. You should see Re-Partition, Auto Reboot and F. Reset Time checked.
7. Click PDA button and select this file: CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar
8. Click PHONE button and select this file: MODEM_I9003XXKPE_REV_00_CL1041909.tar
9. Click BOOTLOADER button and select this file: APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar
10. Click CSC button and select this file: GT-I9003-CSC-MULTI-OXAKPE.tar
11. Click Start button to flash these files to phone.
12. Do not touch anything till you see PASS on the program window.
13. Turn off the phone and set it back into download mode once you get an initial first boot to homescreen. Do not set up anything, Just power off and set to download mode.
Note: You only need to flash once to XXKPE before proceeding to XXKPH
14. In Odin, press Reset button. Re-partition should be unchecked automatically.
15. Select file I9003XXKPH_I9003XXKPH_I9003SERKPH_HOME.tar as PDA
16. Click on Start to flash XXKPH PDA to phone
17. Once you have flashed, after the phone started up, press *#1234# and check your PDA,Phone and CSC, everything should ended with KPH
18. Factory reset and enjoy
1. Firstly, Download the link from Krazzy's stock firmware thread.
2. Run Odin3 v1.83
3. Check Re-Partition, Auto Reboot and F. Reset Time.
4. Click PIT button and select this file: latona_20110114.pit
5. Set it to download mode : Press Volume down + OK first, then hold Power button.
6. Connect USB cable and the program will detect the phone's Com number.
7. Click Start button to download the PIT file to phone.
8. After it is Done Click on Reset button [Partition box should be unchecked automatically - Thanks to jaskir]
9. Click PDA button and select this file: CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar
10. Click PHONE button and select this file: MODEM_I9003XXKPE_REV_00_CL1041909.tar
11. Click BOOTLOADER button and select this file: APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar
12. Click CSC button and select this file: GT-I9003-CSC-MULTI-OXAKPE.tar
13: You should unplug usb cable, remove battery, insert battery and bring it back to download mode. I have never been able to bring it to download mode with usb plugged in. [Thanks to jaskir for this suggestion to make it clear to new users!]
14. Click Start button to flash these files to phone.
15. Do not touch anything till you see PASS on the program window.
16. Factory reset
17. [To fix issues that pertain] Reflash from steps 9 -15 again, No need of latona at this point.
1. Make all your backups using TB. Don't forget to move the TB folder to Ext_SD or PC after backing up.
2. Factory reset phone using manual code. (*2767*3855#)
3. Get into recovery mode and wipe all.
4. Now flash the new ROM as usual (latona and then the remaining 4 files.) Be sure not to make any lame errors here.
5. Factory reset again using manual code.
6. Now check to see if the power button functions and the phone reboots when you ask so. (It should work.)
7. Check camera. If you have a black screen, its okay.
8. Factory reset again using manual code.
9. Redo flash procedure again.
10. Factory reset again.
11. Check power button issue and camera. Both should be totally fine.
12. Press power button to lock and leave device for 10 mins. Now, press power button to check if the device wakes up as normal. It should. If you want to avoid the device being woken up by calls or texts or other notifications, just put it into flight mode and turn off Wi-Fi.
13. Root using SuperOneClick. It will show up Kernel Panic error in the end, but its no problem.
14. Just pull battery after that and restart phone. You should see SuperUser installed and working. Upgrade Busybox to 1.18.4 by Stericson.
15. Now install TB and go about your restoring business. DO NOT restore any system apps. Just restore User Apps and data.
16. If you didn't **** up any of the above, you should be up and running 2.3.4 without any issues (yet!).
thanks to spacebar2011 for his version.
1. Firstly, Download the link from Krazzy's stock firmware thread. [Apprently it's been proven recently its 2.3.4 GingerBread and not 2.3.3 ] [Link Below]
2. Run Odin3 v1.83
3. Check Re-Partition, Auto Reboot and F. Reset Time.
4. Click PIT button and select this file: latona_20110114.pit
5. Set it to download mode : Press Volume down + OK first, then hold Power button.
6. Connect USB cable and the program will detect the phone's Com number.
7. Click Start button to download the PIT file to phone.
8. After it is Done Click on Reset button [Partition box should be unchecked automatically - Thanks to jaskir]
9. Click PDA button and select this file: CODE_I9003XXKP7_CL280937_REV08_eng_mid_ship.tar
10. Click PHONE button and select this file: MODEM_I9003XXKP7_REV_00_CL1021949.tar
11. Click BOOTLOADER button and select this file: APBOOT_I9003XXKP7_CL280937_REV08_eng_mid_ship
12. Click CSC button and select this file: GT-I9003-CSC-MULTI-OXAKP7.tar
13: You should unplug usb cable, remove battery, insert battery and bring it back to download mode. I have never been able to bring it to download mode with usb plugged in. [Thanks to jaskir for this suggestion to make it clear to new users!]
14. Click Start button to flash these files to phone.
15. Do not touch anything till you see PASS on the program window.
16. Factory reset
Note: At this point tested and discussed with many users, Update at your own risk, Help will be provided considering it doesn't go off topic.
Also take note, This is a DEV RELEASE, Its bearable. But worth to kill your curiosity over.
KPE Feedback Thread credits go to ephraim
KP9 Feedback Thread credits go to rb210
Falex FAQ on EVERYTHING you need to know about your phone.
DOWNLOAD THE FIRMWARES FROM THIS THREAD : http://forum.xda-developers.com/showthread.php?p=12310841#post12310841
Credit to Krazy for his time and effort in updating the thread. And to everyone in the Gingerbread I9003 Feedback thread.
Notes: I have removed the findings as I have already linked the Feedback threads for the respective firmwares, Please read the feedback to know the problems for the respective GB firmwares.
3:36 Decided to give the thread a whole clean new look
4:20 Added falex FAQ to feedback.
-----------
3:43 Added XXKPH Guide Updated.
------------
7:53 Oct 20, Added XXKPM Guide.
Note : When I have time to download the other azn version's I will write up a guide. Kindly post the firmware ID for which firmware you need a guide.
Dude what is the purpose of making another similar thread related to flashing
kkrraazzyy said:
Dude what is the purpose of making another similar thread related to flashing
Click to expand...
Click to collapse
Too many keep asking about the Bootloader question, So far its a must.
Okk buddy then it is useful for others
kkrraazzyy said:
Okk buddy then it is useful for others
Click to expand...
Click to collapse
Thanks for understanding And for related threads
Hmm mah pleasure dude
revert back
please tell me can we revert back to froyo to claim warranty.
podanimesh said:
please tell me can we revert back to froyo to claim warranty.
Click to expand...
Click to collapse
I think you can flash it back. Just not sure about the bootloader staying the same, Chances are the Froyo's camera and power button wont work. Way to reverse psycho.
Also it should be safe, Anything done in Download Mode can be reversed and changed. But if not in download. Nice paperweight.
Note: Think the warranty only becomes void when you root. Cause thats tampering with system files
Reference to step 8, After it is Done Click on Reset button, then unselect Re-Partition box.
when you click Reset, Re-Partition is automatically unselected
jaskiratsingh said:
Reference to step 8, After it is Done Click on Reset button, then unselect Re-Partition box.
when you click Reset, Re-Partition is automatically unselected
Click to expand...
Click to collapse
Thanks for the update! Appreciate it
kkrraazzyy said:
Hmm mah pleasure dude
Click to expand...
Click to collapse
Did you apply this update? What is your opinion?
Sent from my GT-I9003 using XDA App
jesrani said:
Did you apply this update? What is your opinion?
Sent from my GT-I9003 using XDA App
Click to expand...
Click to collapse
It is quite buggy but fast
Sent from my GT-I9003 using XDA Premium App
sakindia123 said:
It is quite buggy but fast
Sent from my GT-I9003 using XDA Premium App
Click to expand...
Click to collapse
what sort of bugs did you notice?
ritvik93 said:
what sort of bugs did you notice?
Click to expand...
Click to collapse
hangups,random reboots,and power button cant reboot
is this a buggy update
manishnraj said:
is this a buggy update
Click to expand...
Click to collapse
@Mashin Kinda, Its a dev firmware. So its still glitchy but bearable, Since original was supposed to be launched on July/Sept. Depends on regions.
I am in my college and so i havnt flashed it yet but soon will give a try
So far the details as follows:
firmware version:i9003xxkp7
kernel version:2.6.35.7-cl280937
[email protected]#1
build number:gt-i9003-eng 2.3.4 GINGERBRED XXKP7 test-keys.
Could use some feedback @ kkrraazzyy, The current issue is the SOD when boot flashed.
Guys! I live in Argentina and my i9003 is I9003LUBKB1
Do I have to wait to my exactly firmware version? Thanks!!
dieguite said:
Guys! I live in Argentina and my i9003 is I9003LUBKB1
Do I have to wait to my exactly firmware version? Thanks!!
Click to expand...
Click to collapse
Flashing with XXKP7 will be just fine. My orignal is DXKB2 i think but i flashed to XXKB3 with no problems. XXKB3 is a european version but i am from Philippines. I suggest that we should wait for a more stable GB version because this one has a lot of bugs.
Sent from my GT-I9003 using XDA App
Just saw the heat on the GT-P6210 UK firmware release and checked on Samfirmware.
Flashed this using Mobile ODIN directly OVER the KL3 deodexed firmware, no major issues so far (unable to set voicemail number).
All settings/prefs/apps preserved
Download link from Hotfile, feel free to mirror elsewhere
http://www.hotfile.com/dl/162811167/9e67b52/P6200XXLQ1_P6200OXALQ1_ATO.zip.html
Beware, extracted, this file is nearly 850Mb in size
Also, thanks to anyone who roots this!
Aaron.
P.S. Screenshot
https://plus.google.com/u/0/111032879558038139743/posts/aD54hVuaVBz
-----
** UPDATE **
Brand new UK P6200 firmware available dated November 2012
PDA: P6200XXLQ7
CSC: P6200XEULP1
http://www.hotfile.com/dl/179423658/bf830d8/P6200XXLQ7_P6200XEULP1_XEU.zip.html
Same as previous. I flashed this directly over my previous firmware using Mobile Odin Pro. I had to flash SuperSU binaries afterwards to gain proper root access.
Root is easy for this firmware!
When flashing via Mobile Odin, clear the flash for recovery image (i.e. do not flash recovery)
Then flash SuperSU afterwards via recovery
http://download.chainfire.eu/204/SuperSU/CWM-SuperSU-v0.94.zip
how much it take time, i flash with mobile odin about 20 minute ago and my tab still on samsung logo !
It should take up to 7 minutes to complete the process, including boot up.
ali_ge said:
how much it take time, i flash with mobile odin about 20 minute ago and my tab still on samsung logo !
Click to expand...
Click to collapse
Took mine around 5 minutes to flash, then another few mins to get to the "upgrading screen" (which is simply android creating the relevant dexes).
acolwill said:
Took mine around 5 minutes to flash, then another few mins to get to the "upgrading screen" (which is simply android creating the relevant dexes).
Click to expand...
Click to collapse
hi can i just flash this with my stock p6200?
stock baseband kernel etc.
Justinhopaolo said:
hi can i just flash this with my stock p6200?
stock baseband kernel etc.
Click to expand...
Click to collapse
Should be no issues. I *would* flash the CWM recovery tho.
Uhm, for some strange reason none of my 2 PCs is able to see P6200 while in recovery mode. Everything is working fine if I connect my GS3 to those PCs. Any clue?
Try using Mobile Odin ;-)
It has worked pretty well for me.
Edit : I had a stock ROM / RECOVERY / ... Only rooted my device.
i'm mirroring the ICS Austria Firmware on media fire. Feel free to download.
part1 - part2 - part3
can i install roms without using an sd card?
Justinhopaolo said:
can i install roms without using an sd card?
Click to expand...
Click to collapse
yes.. but use odin.
motosuki said:
yes.. but use odin.
Click to expand...
Click to collapse
In another thread you say no. What's your final answer
Sent from my GT-P6200 using xda premium
Justinhopaolo said:
In another thread you say no. What's your final answer
Sent from my GT-P6200 using xda premium
Click to expand...
Click to collapse
you need to use pc + odin to flash this firmware. it doesn't require external sdcard. it is different when you flashing custom ROM, you need external sdcard to put the zip file.
motosuki said:
you need to use pc + odin to flash this firmware. it doesn't require external sdcard. it is different when you flashing custom ROM, you need external sdcard to put the zip file.
Click to expand...
Click to collapse
Hi I'm sorry, I hope its not too much of a drag for you. Bit can you give me steps?
I already have the mobile Odin.
Sent from my GT-P6200 using xda premium
Justinhopaolo said:
Hi I'm sorry, I hope its not too much of a drag for you. Bit can you give me steps?
I already have the mobile Odin.
Sent from my GT-P6200 using xda premium
Click to expand...
Click to collapse
1. download samsung kies to get the correct driver for gt-p6200
2. download odin3 v.1.85
3. download Stock Firmware Austria - P6200XXLQ1_P6200OXALQ1_ATO.zip
4. install Kies
5. extract Odin3-v1.85.zip
6. extract P6200XXLQ1_P6200OXALQ1_ATO.zip until you get file P6200OXALQ1_P6200XXLQ1_P6200XXLQ1_HOME.tar.md5
7. turn off your tablet
8. enter download mode (press volume up button + power button about 5 seconds)
9. plug the usb cable to your pc and your tablet
10. run Odin3 v1.85.exe
11. check if pc recognize your tablet by seeing ID:COM turn yellow and "Added!!" message in the message box lower left odin window.
12. klik PDA button and put P6200OXALQ1_P6200XXLQ1_P6200XXLQ1_HOME.tar.md5
13. make sure to uncheck re-partition
14. click start
15. odin processing takes about 5 minutes, wait patiently.
16. if there's a "SUCCEED" in the message box, your tablet will restart
17. wait about 10 minutes, you should get your ICS boot to system
if it's not....
18. if your tablet didn't boot, you need to wipe cache / factory reset in the recovery mode
19. turn off your tablet.
20. press volume up + power button about 5 seconds.
21. do wipe cache / factory reset
22. reboot to system
23. it should be booting to system
if it's not...
contact nearest samsung service center
motosuki said:
1. download samsung kies to get the correct driver for gt-p6200
2. download odin3 v.1.85
3. download Stock Firmware Austria - P6200XXLQ1_P6200OXALQ1_ATO.zip
4. install Kies
5. extract Odin3-v1.85.zip
6. extract P6200XXLQ1_P6200OXALQ1_ATO.zip until you get file P6200OXALQ1_P6200XXLQ1_P6200XXLQ1_HOME.tar.md5
7. turn off your tablet
8. enter download mode (press volume up button + power button about 5 seconds)
9. plug the usb cable to your pc and your tablet
10. run Odin3 v1.85.exe
11. check if pc recognize your tablet by seeing ID:COM turn yellow and "Added!!" message in the message box lower left odin window.
12. klik PDA button and put P6200OXALQ1_P6200XXLQ1_P6200XXLQ1_HOME.tar.md5
13. make sure to uncheck re-partition
14. click start
15. odin processing takes about 5 minutes, wait patiently.
16. if there's a "SUCCEED" in the message box, your tablet will restart
17. wait about 10 minutes, you should get your ICS boot to system
if it's not....
18. if your tablet didn't boot, you need to wipe cache / factory reset in the recovery mode
19. turn off your tablet.
20. press volume up + power button about 5 seconds.
21. do wipe cache / factory reset
22. reboot to system
23. it should be booting to system
if it's not...
contact nearest samsung service center
Click to expand...
Click to collapse
is this the method if i want to flash other roms, like cm9?
Justinhopaolo said:
is this the method if i want to flash other roms, like cm9?
Click to expand...
Click to collapse
you need to use CWM recovery.
1. download CWM recovery
2. copy CWM file into your external sdcard
3. turn off your tablet
4. enter recovery mode, press volume up + power button about 5 minutes
5. use volume button to navigate and power button to choose
6. choose "apply update from external storage"
7. find p6200_CWMR_20111214.zip
8. push power button to choose, and wait until instalation finished
9. your tablet will reboot
to install CM9
1. download custom rom you want to install
2. put it in your external sdcard
3. turn off your tablet
4. enter recovery mode, press volume up + power button about 5 minutes
5. use volume button to navigate and power button to choose
6. choose "install zip from sdcard" and "choose zip from internal sdcard"
7. find the custom rom zip file
8. push power button to choose, and wait until instalation finished
9. choose go back until you find wipe data / factory reset
10. choose yes
11. choose wipe cache partition
12. choose yes
13. reboot system now
that should do it... and make sure you use the right custom ROM for your tablet model.
whenever ichoose apply update from external. it say no such directory or file etc..
howcome?
Justinhopaolo said:
whenever ichoose apply update from external. it say no such directory or file etc..
howcome?
Click to expand...
Click to collapse
did you succeed installing CWM? or you still trying to install CWM?
i make some correction in the tutorial... please read again.
My phone gives black screen almost 5 to 6 times an hour.I have to 're insert the battery n reboot it. I think it's a soft brick. What I did was
I was on kpu using thefrankenstien rom then went on to kpe>kpe>kpq>remics v1.5.
Please help.
Sent from my GT-I9003 using xda app-developers app
Come on!.no one to help me here? Need urgent help.
Sent from my GT-I9003 using xda app-developers app
I think u have to make a clean install with pit->kpe->kph->kpq->kpu with the latest cf-root and then the Rom from ext.sd via cwm
Sent from my GT-I9003 using xda app-developers app
ollivong said:
I think u have to make a clean install with pit->kpe->kph->kpq->kpu with the latest cf-root and then the Rom from ext.sd via cwm
Sent from my GT-I9003 using xda app-developers app
Click to expand...
Click to collapse
Hey. It would be really nice if you could give me step wise instructions or give me a link that could guide me. I don't want to risk it . Thanx
Sent from my GT-I9003 using xda app-developers app
I have there a Problem.i'm from germany
Sent from my GT-I9003 using xda app-developers app
Hi Herr US something
Note: XXKPQ can only be flashed with help from it's supporting predecessor XXKPE like the XXKPN/XXKPH/XXKPM series, So make sure you have XXKPE downloaded. User flashing version varies with this, but this is my successful 100% assured boot.
Note: For those of you receiving WiFi drop issues, Assign a static IP using
Static IP [Download Here], hit the advanced tab and let it auto configure. Credit to [thatguyonfacebookiforgot]
1. Firstly, Download the 2.3.6 firmware from Przekret's thread
2. Run Odin3 v1.83
3. Set your phone to download mode : Press Volume down + OK first, then hold Power button.
4. Connect your phone, you should see Odin shows your phone is Added with COM number.
5. Click PIT button and select this file: latona_20110114.pit
6. You should see Re-Partition, Auto Reboot and F. Reset Time checked.
7. Click PDA button and select this file: CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar
8. Click PHONE button and select this file: MODEM_I9003XXKPE_REV_00_CL1041909.tar
9. Click BOOTLOADER button and select this file: APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar
10. Click CSC button and select this file: GT-I9003-CSC-MULTI-OXAKPE.tar
11. Click Start button to flash these files to phone.
12. Do not touch anything till you see PASS on the program window.
13. Turn off the phone and set it back into download mode once you get an initial first boot to homescreen. Do not set up anything, Just power off and set to download mode.
Note: You only need to flash once to XXKPE before proceeding to XXKPQ
14. In Odin, press Reset button. Re-partition should be unchecked automatically.
15. Select file I9003XXKPQ_I9003XXKPQ_I9003SERKPQ_HOME.tar.md5 as PDA
16. Click on Start to flash XXKPQ PDA to phone
17. Once you have flashed, after the phone started up, press *#1234# and check your PDA,Phone and CSC, everything should ended with KPQ
18. Factory reset and enjoy
Note: XXKPN can only be flashed with help from it's supporting predecessor XXKPE like the XXKPH/XXKPM series, So make sure you have XXKPE downloaded. User flashing version varies with this, but this is my successful 100% assured boot. This firmware is to fix the issues that pertained and caused some WiFi issues for other's
1. Firstly, Download the 2.3.5 firmware from Przekret's thread
2. Run Odin3 v1.83
3. Set your phone to download mode : Press Volume down + OK first, then hold Power button.
4. Connect your phone, you should see Odin shows your phone is Added with COM number.
5. Click PIT button and select this file: latona_20110114.pit
6. You should see Re-Partition, Auto Reboot and F. Reset Time checked.
7. Click PDA button and select this file: CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar
8. Click PHONE button and select this file: MODEM_I9003XXKPE_REV_00_CL1041909.tar
9. Click BOOTLOADER button and select this file: APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar
10. Click CSC button and select this file: GT-I9003-CSC-MULTI-OXAKPE.tar
11. Click Start button to flash these files to phone.
12. Do not touch anything till you see PASS on the program window.
13. Turn off the phone and set it back into download mode once you get an initial first boot to homescreen. Do not set up anything, Just power off and set to download mode.
Note: You only need to flash once to XXKPE before proceeding to XXKPN
14. In Odin, press Reset button. Re-partition should be unchecked automatically.
15. Select file I9003XXKPN_I9003XXKPN_I9003SERKPN_HOME.tar.md5 as PDA
16. Click on Start to flash XXKPN PDA to phone
17. Once you have flashed, after the phone started up, press *#1234# and check your PDA,Phone and CSC, everything should ended with KPN
18. Factory reset and enjoy
Note: XXKPM can only be flashed with help from it's supporting predecessor XXKPE like the XXKPH series, So make sure you have XXKPE downloaded. User flashing version varies with this, but this is my successful 100% assured boot.
1. Firstly, Download the 2.3.5 firmware from Przekret's thread
2. Run Odin3 v1.83
3. Set your phone to download mode : Press Volume down + OK first, then hold Power button.
4. Connect your phone, you should see Odin shows your phone is Added with COM number.
5. Click PIT button and select this file: latona_20110114.pit
6. You should see Re-Partition, Auto Reboot and F. Reset Time checked.
7. Click PDA button and select this file: CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar
8. Click PHONE button and select this file: MODEM_I9003XXKPE_REV_00_CL1041909.tar
9. Click BOOTLOADER button and select this file: APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar
10. Click CSC button and select this file: GT-I9003-CSC-MULTI-OXAKPE.tar
11. Click Start button to flash these files to phone.
12. Do not touch anything till you see PASS on the program window.
13. Turn off the phone and set it back into download mode once you get an initial first boot to homescreen. Do not set up anything, Just power off and set to download mode.
Note: You only need to flash once to XXKPE before proceeding to XXKPM
14. In Odin, press Reset button. Re-partition should be unchecked automatically.
15. Select file I9003XXKPM_I9003XXKPM_I9003SERKPM_HOME.tar.md5 as PDA
16. Click on Start to flash XXKPM PDA to phone
17. Once you have flashed, after the phone started up, press *#1234# and check your PDA,Phone and CSC, everything should ended with KPM
18. Factory reset and enjoy
From Custom ROM's [Must be GINGERBREAD, Not Froyo, I am not responsible if your phone ends in a bootloop from ignorance]:
1. Just flash I9003XXKPM_I9003XXKPM_I9003SERKPM_HOME.tar.md5 in PDA as usual.
2. The phone will end up in a bootloop due to ext4 conversion, Proceed to step 3.
3. Flash Skin's CFRoot in respective PDA.
4. Boot into Custom Recovery via 3 Button Combo.
5. Select option's Wipe Cache and Factory Reset
6. Voila, Enjoy your new easy flashable method.
Note: XXKPH can only be flashed with help from it's supporting predecessor XXKPE, So make sure you have XXKPE downloaded. User flashing version varies with this, but this is my successful 100% assured boot.
1. Firstly, Download the link from spacebar's XXKPH Feedback thread.
2. Run Odin3 v1.83
3. Set your phone to download mode : Press Volume down + OK first, then hold Power button.
4. Connect your phone, you should see Odin shows your phone is Added with COM number.
5. Click PIT button and select this file: latona_20110114.pit
6. You should see Re-Partition, Auto Reboot and F. Reset Time checked.
7. Click PDA button and select this file: CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar
8. Click PHONE button and select this file: MODEM_I9003XXKPE_REV_00_CL1041909.tar
9. Click BOOTLOADER button and select this file: APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar
10. Click CSC button and select this file: GT-I9003-CSC-MULTI-OXAKPE.tar
11. Click Start button to flash these files to phone.
12. Do not touch anything till you see PASS on the program window.
13. Turn off the phone and set it back into download mode once you get an initial first boot to homescreen. Do not set up anything, Just power off and set to download mode.
Note: You only need to flash once to XXKPE before proceeding to XXKPH
14. In Odin, press Reset button. Re-partition should be unchecked automatically.
15. Select file I9003XXKPH_I9003XXKPH_I9003SERKPH_HOME.tar as PDA
16. Click on Start to flash XXKPH PDA to phone
17. Once you have flashed, after the phone started up, press *#1234# and check your PDA,Phone and CSC, everything should ended with KPH
18. Factory reset and enjoy
1. Firstly, Download the link from Krazzy's stock firmware thread.
2. Run Odin3 v1.83
3. Check Re-Partition, Auto Reboot and F. Reset Time.
4. Click PIT button and select this file: latona_20110114.pit
5. Set it to download mode : Press Volume down + OK first, then hold Power button.
6. Connect USB cable and the program will detect the phone's Com number.
7. Click Start button to download the PIT file to phone.
8. After it is Done Click on Reset button [Partition box should be unchecked automatically - Thanks to jaskir]
9. Click PDA button and select this file: CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar
10. Click PHONE button and select this file: MODEM_I9003XXKPE_REV_00_CL1041909.tar
11. Click BOOTLOADER button and select this file: APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar
12. Click CSC button and select this file: GT-I9003-CSC-MULTI-OXAKPE.tar
13: You should unplug usb cable, remove battery, insert battery and bring it back to download mode. I have never been able to bring it to download mode with usb plugged in. [Thanks to jaskir for this suggestion to make it clear to new users!]
14. Click Start button to flash these files to phone.
15. Do not touch anything till you see PASS on the program window.
16. Factory reset
17. [To fix issues that pertain] Reflash from steps 9 -15 again, No need of latona at this point.
1. Make all your backups using TB. Don't forget to move the TB folder to Ext_SD or PC after backing up.
2. Factory reset phone using manual code. (*2767*3855#)
3. Get into recovery mode and wipe all.
4. Now flash the new ROM as usual (latona and then the remaining 4 files.) Be sure not to make any lame errors here.
5. Factory reset again using manual code.
6. Now check to see if the power button functions and the phone reboots when you ask so. (It should work.)
7. Check camera. If you have a black screen, its okay.
8. Factory reset again using manual code.
9. Redo flash procedure again.
10. Factory reset again.
11. Check power button issue and camera. Both should be totally fine.
12. Press power button to lock and leave device for 10 mins. Now, press power button to check if the device wakes up as normal. It should. If you want to avoid the device being woken up by calls or texts or other notifications, just put it into flight mode and turn off Wi-Fi.
13. Root using SuperOneClick. It will show up Kernel Panic error in the end, but its no problem.
14. Just pull battery after that and restart phone. You should see SuperUser installed and working. Upgrade Busybox to 1.18.4 by Stericson.
15. Now install TB and go about your restoring business. DO NOT restore any system apps. Just restore User Apps and data.
16. If you didn't **** up any of the above, you should be up and running 2.3.4 without any issues (yet!).
thanks to spacebar2011 for his version.
1. Firstly, Download the link from Krazzy's stock firmware thread. [Apprently it's been proven recently its 2.3.4 GingerBread and not 2.3.3 ] [Link Below]
2. Run Odin3 v1.83
3. Check Re-Partition, Auto Reboot and F. Reset Time.
4. Click PIT button and select this file: latona_20110114.pit
5. Set it to download mode : Press Volume down + OK first, then hold Power button.
6. Connect USB cable and the program will detect the phone's Com number.
7. Click Start button to download the PIT file to phone.
8. After it is Done Click on Reset button [Partition box should be unchecked automatically - Thanks to jaskir]
9. Click PDA button and select this file: CODE_I9003XXKP7_CL280937_REV08_eng_mid_ship.tar
10. Click PHONE button and select this file: MODEM_I9003XXKP7_REV_00_CL1021949.tar
11. Click BOOTLOADER button and select this file: APBOOT_I9003XXKP7_CL280937_REV08_eng_mid_ship
12. Click CSC button and select this file: GT-I9003-CSC-MULTI-OXAKP7.tar
13: You should unplug usb cable, remove battery, insert battery and bring it back to download mode. I have never been able to bring it to download mode with usb plugged in. [Thanks to jaskir for this suggestion to make it clear to new users!]
14. Click Start button to flash these files to phone.
15. Do not touch anything till you see PASS on the program window.
16. Factory reset
Note: At this point tested and discussed with many users, Update at your own risk, Help will be provided considering it doesn't go off topic.
Also take note, This is a DEV RELEASE, Its bearable. But worth to kill your curiosity over.
KPE Feedback Thread credits go to ephraim
KP9 Feedback Thread credits go to rb210
Falex FAQ on EVERYTHING you need to know about your phone.
DOWNLOAD THE FIRMWARES FROM THIS THREAD : http://forum.xda-developers.com/showthread.php?p=12310841#post12310841
Credit to Krazy for his time and effort in updating the thread. And to everyone in the Gingerbread I9003 Feedback thread.
Notes: I have removed the findings as I have already linked the Feedback threads for the respective firmwares, Please read the feedback to know the problems for the respective GB firmwares.
3:36 Decided to give the thread a whole clean new look 
4:20 Added falex FAQ to feedback.
-----------
3:43 Added XXKPH Guide Updated.
------------
7:53 Oct 20, Added XXKPM Guide.
Note : When I have time to download the other azn version's I will write up a guide. Kindly post the firmware ID for which firmware you need a guide.
Sent from my GT-I9003 using xda app-developers app
Hey can u give me files for xxkpm that you've selected in pda that code_xx
And selected in phone
Sent from my GT-S5570 using xda premium
Hii guyz here is the collection of some of the original roms of Samsung Galaxy S i9003 and if you want to check your firmware version then just type *#1234# in the dialpad
FROYO :
1.I9003XXJL9 - http://www.fileserve.com/file/jf7HvgM/I9003_XXJL9.rar
2.I9003ZCKA6 - http://hotfile.com/dl/99699364/58a8b10/I9003ZCKA6.rar.html
3.I9003XXKA7 - http://hotfile.com/dl/104906620/d07f91d/I9003_XXKA7.rar.html
4.I9003XXKA8 - http://hotfile.com/dl/100569734/423c587/I9003XXKA8.rar.html
5.I9003XXKA9 - http://hotfile.com/dl/104942852/338402d/I9003_XXKA9.rar.html
6.I9003XXKB1 - http://hotfile.com/dl/104985993/f064b46/I9003_XXKB1.rar.html
7.I9003XXKB1-CSC-DBTKB2 - http://hotfile.com/dl/108472094/caf22ab/I9003_XXKB1-CSC-DBTKB2.rar.html
8.I9003XEKB1- http://hotfile.com/dl/103455459/5de363e/I9003XEKB1.rar.html
9.I9003XXKB3 : http://hotfile.com/dl/109632538/8b50540/I9003XXKB3.rar.html
10.I9003DXKB2 : http://hotfile.com/dl/112533344/d0ffba9/I9003DXKB2.rar.html
11. I9003ZTKC1_ZZTKC1 : http://hotfile.com/dl/114690468/e631c21/I9003ZTKC1_ZZTKC1.rar.html
12. I9003JPKD1 : http://hotfile.com/dl/115297948/cd1ebc2/I9003JPKD1.rar.html
13. I9003DDKB2 : http://hotfile.com/dl/118886369/41e2d28/I9003DDKB2_ODDKA6_DDKA5.rar.html
14. I9003ZCKC1: http://hotfile.com/dl/115955648/5e2fbcb/I9003ZCKC1.rar.html
15. I9003JBKE1 : http://hotfile.com/dl/120663910/f3ff0d9/I9003JPKE1_OJPKC2_JXKA4.rar.html
16. I900XXKC1 (EUROPEAN) :http://narod.ru/disk/14574272001/I9003.ZIP.html
17. I9003DXKE1 : http://hotfile.com/dl/121540531/c22acf2/I9003DXKE1_OLBKB2_DXKB2.rar.html
18. I9003ZCKE1 : http://hotfile.com/dl/121547281/fcf48e9/I9003ZCKE1_OZH1009173_ZCKE1.rar.html
19. I9003XEKE1 : http://hotfile.com/dl/121542297/63b4dc5/I9003XEKE1_UCLKE4_XXKB1.rar.html
20. I9003DXKF1 : http://hotfile.com/dl/125254491/fc97d74/I9003DXKF1.rar.html
LATEST firmware : I9003DXKf1 (ASIAN) : http://hotfile.com/dl/125254491/fc97d74/I9003DXKF1.rar.html
GINGERBREAD 2.3.4 , 2.3.5 AND 2.3.6
1. I9003XXKP7
Download: http://hotfile.com/dl/145770427/e513390/I9003XXKP7.zip.html
WARNING: DEV/BETA/TEST VERSION | NOT AN OFFICIAL RELEASED SAMSUNG STOCK ROM!
BUGS: YES, id est: SOD, KP, etc.
KIES: NO.
KIES FW INFORMATION: Unknown.
Password: samfirmware.com
2. I9003XXKP9(Android 2.3.4 Build date : Tue Jun 21 22:40:06 KST 2011)
Download: http://hotfile.com/dl/145770782/0762ef0/I9003XXKP9.zip.html
Password: samfirmware.com
WARNING: DEV VERSION | NOT AN OFFICIAL SAMSUNG RELEASED STOCK ROM!
BUGS: YES, less bugs compared with XXKP7
KIES:YES.
KIES FW INFORMATION: "This version of the device cannot be updated.", unless "maybe" you're from Korea.
For Discussion, proceed here: http://forum.xda-developers.com/showthread.php?t=1148158L]
THANX TO Sine. FOR MIRRORS!
3. I9003XXKPE
Download: http://hotfile.com/dl/145780524/f7d1f45/I9003XXKPE.zip.html
Password: samfirmware.com
WARNING: DEV VERSION | NOT AN OFFICIAL SAMSUNG RELEASED STOCK ROM!
BUGS: NO, More Stable than XXKP9
KIES:YES
Mirrors: Multiupload
THANX TO JAMSOORI FOR MIRROR!
4. I9003XXKPH
Download: http://hotfile.com/dl/145784146/61cb31c/I9003XXKPH_I9003XXKPH_I9003SERKPH.zip.html
Password: samfirmware.com
VERSION : AN OFFICIAL SAMSUNG RELEASED STOCK ROM!
BUGS: NO, More Stable than XXKPE
KIES:YES
MIRROR : http://leechfactory.com/9xq0eg11b48g/I9003XXKPH_I9003XXKPH_I9003SERKPH.rar.html
MIRROR : http://oron.com/9nbe4mx50e7u/I9003XXKPH_I9003XXKPH_I9003SERKPH.rar.html
Thanks to Aaditya for the resumable dl link, mjbri0613 & Sine for the mirrors.
5. I9003JPKP5
Download : http://hotfile.com/dl/128277760/323a3f0/I9003JPKP5.rar.html
Password: samfirmware.com
VERSION : AN OFFICIAL SAMSUNG RELEASED STOCK ROM!
BUGS: NO.
KIES:YES
MIRROR: http://www.mediafire.com/?swsk4j35zejt1ck
MIRROR : http://www.4shared.com/file/KnWnCI9B/I9003JPKP5.html
6. I9003XXKPM (2.3.5)
Download : http://hotfile.com/dl/132666832/c6474bf/GT-I9003_SER_I9003XXKPM_I9003XXKPM_I9003SERKPM.rar.html
Password: sampro.pl
VERSION : AN OFFICIAL SAMSUNG RELEASED STOCK ROM!
BUGS: NO.
KIES:YES
6. I9003ZCKP5 (2.3.5)
Download : http://www.multiupload.com/RA1MNES66N
VERSION : AN OFFICIAL SAMSUNG RELEASED STOCK ROM!
BUGS: NO.
KIES:YES
THANKS TO HKF2005HK
7. I9003XXKPN (2.3.5)
Download :http://hotfile.com/dl/145831953/e230a2a/I9003XXKPN_I9003SERKPN_SER.zip.html
Pass: sampro.pl
VERSION : AN OFFICIAL SAMSUNG RELEASED STOCK ROM!
BUGS: NO.
KIES:YES
THANKS TO PRZEKRET
8. I9003DXKP9 (2.3.5)
Download : http://www.multiupload.com/1PQLH31F3L (THANKS TO SINE)
Pass: sampro.pl
VERSION : AN OFFICIAL SAMSUNG RELEASED STOCK ROM!
BUGS: NO.
KIES:YES
9. I9003ZCKP9 (2.3.5)
Download : http://www.multiupload.com/QZNQWL253S (THANKS TO SINE)
Pass: sampro.pl
VERSION : AN OFFICIAL SAMSUNG RELEASED STOCK ROM!
BUGS: NO.
KIES:YES
10. I9003POKP3 (2.3.5)
Download : http://www.multiupload.com/GUDBUFR46U (THANKS TO SINE)
Pass: sampro.pl
VERSION : AN OFFICIAL SAMSUNG RELEASED STOCK ROM!
BUGS: NO.
KIES:YES
11. I9003XWKPG (2.3.5)
Download : http://www.multiupload.com/90HCRDPADU (THANKS TO SINE)
Pass: sampro.pl
VERSION : AN OFFICIAL SAMSUNG RELEASED STOCK ROM!
BUGS: NO.
KIES:YES
12. I9003XXKPQ (2.3.6)
Download : http://hotfile.com/dl/145857619/824249e/I9003XXKPQ_I9003SERKPQ_SER.zip.html (THANKS TO SINE)
Pass: sampro.pl
VERSION : AN OFFICIAL SAMSUNG RELEASED STOCK ROM!
BUGS: NO.
KIES:YES
13. I9003UBKPD (2.3.6)
Download : http://www.megaupload.com/?d=L9SKRMSS(THANKS TO Uan_ar)
Password: grupoandroid.com
VERSION : AN OFFICIAL SAMSUNG RELEASED STOCK ROM!
BUGS: NO.
KIES:YES
14. I9003XXKPU (2.3.6)
Download:http//www.hotfile.com/dl/148016499/9f88f11/I9003XXKPU_I9003SERKPU_SER.zip.html
Password: samfirmware.com or sampro.pl
VERSION : AN OFFICIAL SAMSUNG RELEASED STOCK ROM!
BUGS: NO.
KIES:YES
15. I9003XWLF2 (2.3.6)
Download: https://hotfile.com/dl/161664001/2936958/GT-I9003_XEO_I9003XWLF2_I9003OXXLF1_I9003XXLE4.zip.html
Password: samfirmware.com or sampro.pl
VERSION : VALUE PACK
BUGS: NO.
KIES:YES
16. I9003DDLF2 (2.3.6)
Download: http://www.hotfile.com/dl/161660941/8fd61ef/I9003DDLF2_I9003ODDLF2_INU.zip.html
Password: samfirmware.com or sampro.pl
VERSION : VALUE PACK
BUGS: NO.
KIES:YES
FEEDBACK THREAD : http://forum.xda-developers.com/showthread.php?t=1222288
WILL UPDATE THIS THREAD REGULARLY
PRESS THE THANKU BUTTON IF YOU LIKE MY POST
All thanks to krazy for his work
Sent from my GT-I9003 using xda app-developers app
ollivong pls give credits to kkrraazzy for its his work, you merely copied and pasted.
Sent from my GT-I9003 using xda app-developers app
I'm sorry when i did something wrong. I'm new Herr.what do you mean with credits?
Sent from my GT-I9003 using xda app-developers app
@oliver i would try it out and let you know the result! i would go for kpq!
ollivong said:
I'm sorry when i did something wrong. I'm new Herr.what do you mean with credits?
Sent from my GT-I9003 using xda app-developers app
Click to expand...
Click to collapse
He meant rather than copy paste the whole post by kkrraazzyy, you should have just posted a link to his thread.
Or atleast, you should have mentioned where did you get this info from.
That is how open-source works. :angel:
Hetalk said:
He meant rather than copy paste the whole post by kkrraazzyy, you should have just posted a link to his thread.
Or atleast, you should have mentioned where did you get this info from.
That is how open-source works. :angel:
Click to expand...
Click to collapse
Yup @ollivong. Don't worry abt it though . We're nice people as long as you are polite.
Sent from my GT-I9003 using xda app-developers app
bscraze said:
Don't worry abt it though . We're nice people as long as you are polite.
Click to expand...
Click to collapse
Thanks men. With The xda-app isn't it so easy to learn but i will learn it
Sent from my GT-I9003 using xda app-developers app
ollivong said:
Thanks men. With The xda-app isn't it so easy to learn but i will learn it
Sent from my GT-I9003 using xda app-developers app
Click to expand...
Click to collapse
Hey i tried your method of installin kpq. But the problem still exists though the frequency of black screen has decreased.
Sent from my GT-I9003 using xda app-developers app
i have a small douts on my mobile
hey im using galaxy sl(i9003xwkpg) i have rooted with this software 'unlockroot' and in rom manager i trying to install cwm means its asking to select model no, its showing only two model nos that is samsung i9000 and samsung 4gepic but my model no is nt showing(i9003)
how can i install cwm pls help me
navinash.avi said:
hey im using galaxy sl(i9003xwkpg) i have rooted with this software 'unlockroot' and in rom manager i trying to install cwm means its asking to select model no, its showing only two model nos that is samsung i9000 and samsung 4gepic but my model no is nt showing(i9003)
how can i install cwm pls help me
Click to expand...
Click to collapse
Use universal cfroot. U get root & cwm in 1 pack.
Find it at development threat.
Sent from my GT-I9003 using Tapatalk 2
chongns said:
Use universal cfroot. U get root & cwm in 1 pack.
Find it at development threat.
Sent from my GT-I9003 using Tapatalk 2
Click to expand...
Click to collapse
i have to again un root n i should use universal cfroot na and if in any resaons i get again unroot from universial cfroot
Buddy the easiest way i found is , flash it with a exixting and working CFRoot or any other Kernal compatable with your rom , that should correct it , or do a Titanium backup and Flash the firmware again ..
Hit Thanks If It Helped
I was trying to go back to XXPE from XXPQ to flash my phone clean again - after flashing latona to my phone, it doesnt boot any more. Any help?
Follow the steps........
1 Download mode
2 start odin
3 connect via usb
4 select pit latona_20110114
5 boot APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar
6 pda CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar
7 phone MODEM_I9003XXKPE_REV_00_CL1041909.tar
8 csc GT-I9003-CSC-MULTI-OXAKPE.tar
9 press start
10 enjoy
You will need following before beginning installation:
1) Flsher Program + PIT (ODIN3 + Latona.PIT)
2) Firmware: I9003XXKPE
STEPS:
1) Open ODIN. Connect ur phone in download mode. just flash Latona.PIT file with Re-Partition selected.
2) Once flashed, Ur phone will reboot automatically but will show only black screen with background light. Do not worry. Open the back cover, remove the battery, insert battery and boot again in download mode.
3) Close ODIN. Open it again. Now we will be installing XXKPE.
i) Select Latona.PIT File in ODIN. (Make sure the "Re-Partition" is unchecked once you have selected PIT file)
ii) Select "APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar.md5" in bootloader.
iii) Select "CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar.md5" in PDA.
iv) Select "MODEM_I9003XXKPE_REV_00_CL1041909.tar.md5" in PHONE.
v) Select "GT-I9003-CSC-MULTI-OXAKPE.tar.md5" in CSC.
Now flash it.
this will successfully install XXKPE on ur device. Once your flash is complete, ur device will boot and will ask for initial config.
my phones gotten much slower than it used to be...the most adventurous ive gotten with my phone was to update it...through kies that is...
so googling my way i got to xda forums...and on the registry i realised that im a total noob!
so i was wondering if anyone here could help me with a step by step procedure of how to root my gti9003 and then help me out with custom ROMs
Dont know if its relevant but the following are my present phone statistics
MODEL:GT-I9003
FIRMWARE: 2.3.6
BASEBAND: I9003DDLE1
KERNEL: 2.6.35.7-CL1153545 [email protected]#1
BUILD NUMBER: GINGERBREAD.DDLF2
ive read a lot on superoneclick and stuff but im not sure if thatll work for my phone.
Thanks
1. flash ddlf2 firmware from her http://www.hotfile.com/dl/161660941/...2_INU.zip.html and password for zip is sampro.pl OR samfirmware
2. then flash cf-root from here http://www.mediafire.com/?0ndawa4g0s851h4 then go to recovery mode by pressing volume up,home button and power button
3. Wipe Data / Factory Reset.
sent from Samsung galaxy S i9003 Remics JB v3
@karanmirchandani96
really appreciate the help..but as i said...im a noob...i couldnt understand much of your reply :/
Fir download the file then
Note: Before I proceed with this part, Samsung has made it VERY EASY for new users to flash compared to the older ones, Unlike the previous version's that require you to flash it twice or such, or separate files, Their newer releases will always be in this format. With one PDA.md5 file. Unfortunately I cannot keep updating this thread with every region as the flashing methods are exactly the same as follows.
1. Firstly, Download the required firmware from here
2. Run Odin3 v3.04 at the bottom of the page.
3. Set your phone to download mode : Press Volume down + OK first, then hold Power button.
4. Connect your phone, you should see Odin shows your phone is Added with COM number.
5. Extract the contents from the zip, You should have a .dll and a 200-300 MB PDA file.
6. At this point you should see Re-Partition, Auto Reboot and F. Reset Time unchecked.
7. Click PDA button and select the only PDA file in the zip folder (Here you should not touch any of the Re-Partition/F.Reset options as the newer Odin automatically selects it for you, how conveinient!)
8. Click Start button to flash these files to phone.
9. Do not touch anything till you see PASS on the program window.
10. Once you have flashed, after the phone started up, press *#1234# and check your PDA,Phone and CSC, everything should be there. (There should not be any "Unavailable")
11. Factory reset and enjoy
Note: XXKPQ can only be flashed with help from it's supporting predecessor XXKPE like the XXKPN/XXKPH/XXKPM series, So make sure you have XXKPE downloaded. User flashing version varies with this, but this is my successful 100% assured boot.
Note: For those of you receiving WiFi drop issues, Assign a static IP using
Static IP [Download Here], hit the advanced tab and let it auto configure. Credit to [thatguyonfacebookiforgot]
1. Firstly, Download the 2.3.6 firmware from Przekret's thread
2. Run Odin3 v1.83
3. Set your phone to download mode : Press Volume down + OK first, then hold Power button.
4. Connect your phone, you should see Odin shows your phone is Added with COM number.
5. Click PIT button and select this file: latona_20110114.pit
6. You should see Re-Partition, Auto Reboot and F. Reset Time checked.
7. Click PDA button and select this file: CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar
8. Click PHONE button and select this file: MODEM_I9003XXKPE_REV_00_CL1041909.tar
9. Click BOOTLOADER button and select this file: APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar
10. Click CSC button and select this file: GT-I9003-CSC-MULTI-OXAKPE.tar
11. Click Start button to flash these files to phone.
12. Do not touch anything till you see PASS on the program window.
13. Turn off the phone and set it back into download mode once you get an initial first boot to homescreen. Do not set up anything, Just power off and set to download mode.
Note: You only need to flash once to XXKPE before proceeding to XXKPQ
14. In Odin, press Reset button. Re-partition should be unchecked automatically.
15. Select file I9003XXKPQ_I9003XXKPQ_I9003SERKPQ_HOME.tar.md5 as PDA
16. Click on Start to flash XXKPQ PDA to phone
17. Once you have flashed, after the phone started up, press *#1234# and check your PDA,Phone and CSC, everything should ended with KPQ
18. Factory reset and enjoy
Note: XXKPN can only be flashed with help from it's supporting predecessor XXKPE like the XXKPH/XXKPM series, So make sure you have XXKPE downloaded. User flashing version varies with this, but this is my successful 100% assured boot. This firmware is to fix the issues that pertained and caused some WiFi issues for other's
1. Firstly, Download the 2.3.5 firmware from Przekret's thread
2. Run Odin3 v1.83
3. Set your phone to download mode : Press Volume down + OK first, then hold Power button.
4. Connect your phone, you should see Odin shows your phone is Added with COM number.
5. Click PIT button and select this file: latona_20110114.pit
6. You should see Re-Partition, Auto Reboot and F. Reset Time checked.
7. Click PDA button and select this file: CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar
8. Click PHONE button and select this file: MODEM_I9003XXKPE_REV_00_CL1041909.tar
9. Click BOOTLOADER button and select this file: APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar
10. Click CSC button and select this file: GT-I9003-CSC-MULTI-OXAKPE.tar
11. Click Start button to flash these files to phone.
12. Do not touch anything till you see PASS on the program window.
13. Turn off the phone and set it back into download mode once you get an initial first boot to homescreen. Do not set up anything, Just power off and set to download mode.
Note: You only need to flash once to XXKPE before proceeding to XXKPN
14. In Odin, press Reset button. Re-partition should be unchecked automatically.
15. Select file I9003XXKPN_I9003XXKPN_I9003SERKPN_HOME.tar.md5 as PDA
16. Click on Start to flash XXKPN PDA to phone
17. Once you have flashed, after the phone started up, press *#1234# and check your PDA,Phone and CSC, everything should ended with KPN
18. Factory reset and enjoy
Note: XXKPM can only be flashed with help from it's supporting predecessor XXKPE like the XXKPH series, So make sure you have XXKPE downloaded. User flashing version varies with this, but this is my successful 100% assured boot.
1. Firstly, Download the 2.3.5 firmware from Przekret's thread
2. Run Odin3 v1.83
3. Set your phone to download mode : Press Volume down + OK first, then hold Power button.
4. Connect your phone, you should see Odin shows your phone is Added with COM number.
5. Click PIT button and select this file: latona_20110114.pit
6. You should see Re-Partition, Auto Reboot and F. Reset Time checked.
7. Click PDA button and select this file: CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar
8. Click PHONE button and select this file: MODEM_I9003XXKPE_REV_00_CL1041909.tar
9. Click BOOTLOADER button and select this file: APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar
10. Click CSC button and select this file: GT-I9003-CSC-MULTI-OXAKPE.tar
11. Click Start button to flash these files to phone.
12. Do not touch anything till you see PASS on the program window.
13. Turn off the phone and set it back into download mode once you get an initial first boot to homescreen. Do not set up anything, Just power off and set to download mode.
Note: You only need to flash once to XXKPE before proceeding to XXKPM
14. In Odin, press Reset button. Re-partition should be unchecked automatically.
15. Select file I9003XXKPM_I9003XXKPM_I9003SERKPM_HOME.tar.md5 as PDA
16. Click on Start to flash XXKPM PDA to phone
17. Once you have flashed, after the phone started up, press *#1234# and check your PDA,Phone and CSC, everything should ended with KPM
18. Factory reset and enjoy
From Custom ROM's [Must be GINGERBREAD, Not Froyo, I am not responsible if your phone ends in a bootloop from ignorance]:
1. Just flash I9003XXKPM_I9003XXKPM_I9003SERKPM_HOME.tar.md5 in PDA as usual.
2. The phone will end up in a bootloop due to ext4 conversion, Proceed to step 3.
3. Flash Skin's CFRoot in respective PDA.
4. Boot into Custom Recovery via 3 Button Combo.
5. Select option's Wipe Cache and Factory Reset
6. Voila, Enjoy your new easy flashable method.
Note: XXKPH can only be flashed with help from it's supporting predecessor XXKPE, So make sure you have XXKPE downloaded. User flashing version varies with this, but this is my successful 100% assured boot.
1. Firstly, Download the link from spacebar's XXKPH Feedback thread.
2. Run Odin3 v1.83
3. Set your phone to download mode : Press Volume down + OK first, then hold Power button.
4. Connect your phone, you should see Odin shows your phone is Added with COM number.
5. Click PIT button and select this file: latona_20110114.pit
6. You should see Re-Partition, Auto Reboot and F. Reset Time checked.
7. Click PDA button and select this file: CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar
8. Click PHONE button and select this file: MODEM_I9003XXKPE_REV_00_CL1041909.tar
9. Click BOOTLOADER button and select this file: APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar
10. Click CSC button and select this file: GT-I9003-CSC-MULTI-OXAKPE.tar
11. Click Start button to flash these files to phone.
12. Do not touch anything till you see PASS on the program window.
13. Turn off the phone and set it back into download mode once you get an initial first boot to homescreen. Do not set up anything, Just power off and set to download mode.
Note: You only need to flash once to XXKPE before proceeding to XXKPH
14. In Odin, press Reset button. Re-partition should be unchecked automatically.
15. Select file I9003XXKPH_I9003XXKPH_I9003SERKPH_HOME.tar as PDA
16. Click on Start to flash XXKPH PDA to phone
17. Once you have flashed, after the phone started up, press *#1234# and check your PDA,Phone and CSC, everything should ended with KPH
18. Factory reset and enjoy
1. Firstly, Download the link from Krazzy's stock firmware thread.
2. Run Odin3 v1.83
3. Check Re-Partition, Auto Reboot and F. Reset Time.
4. Click PIT button and select this file: latona_20110114.pit
5. Set it to download mode : Press Volume down + OK first, then hold Power button.
6. Connect USB cable and the program will detect the phone's Com number.
7. Click Start button to download the PIT file to phone.
8. After it is Done Click on Reset button [Partition box should be unchecked automatically - Thanks to jaskir]
9. Click PDA button and select this file: CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar
10. Click PHONE button and select this file: MODEM_I9003XXKPE_REV_00_CL1041909.tar
11. Click BOOTLOADER button and select this file: APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar
12. Click CSC button and select this file: GT-I9003-CSC-MULTI-OXAKPE.tar
13: You should unplug usb cable, remove battery, insert battery and bring it back to download mode. I have never been able to bring it to download mode with usb plugged in. [Thanks to jaskir for this suggestion to make it clear to new users!]
14. Click Start button to flash these files to phone.
15. Do not touch anything till you see PASS on the program window.
16. Factory reset
17. [To fix issues that pertain] Reflash from steps 9 -15 again, No need of latona at this point.
1. Make all your backups using TB. Don't forget to move the TB folder to Ext_SD or PC after backing up.
2. Factory reset phone using manual code. (*2767*3855#)
3. Get into recovery mode and wipe all.
4. Now flash the new ROM as usual (latona and then the remaining 4 files.) Be sure not to make any lame errors here.
5. Factory reset again using manual code.
6. Now check to see if the power button functions and the phone reboots when you ask so. (It should work.)
7. Check camera. If you have a black screen, its okay.
8. Factory reset again using manual code.
9. Redo flash procedure again.
10. Factory reset again.
11. Check power button issue and camera. Both should be totally fine.
12. Press power button to lock and leave device for 10 mins. Now, press power button to check if the device wakes up as normal. It should. If you want to avoid the device being woken up by calls or texts or other notifications, just put it into flight mode and turn off Wi-Fi.
13. Root using SuperOneClick. It will show up Kernel Panic error in the end, but its no problem.
14. Just pull battery after that and restart phone. You should see SuperUser installed and working. Upgrade Busybox to 1.18.4 by Stericson.
15. Now install TB and go about your restoring business. DO NOT restore any system apps. Just restore User Apps and data.
16. If you didn't **** up any of the above, you should be up and running 2.3.4 without any issues (yet!).
thanks to spacebar2011 for his version.
1. Firstly, Download the link from Krazzy's stock firmware thread. [Apprently it's been proven recently its 2.3.4 GingerBread and not 2.3.3 ] [Link Below]
2. Run Odin3 v1.83
3. Check Re-Partition, Auto Reboot and F. Reset Time.
4. Click PIT button and select this file: latona_20110114.pit
5. Set it to download mode : Press Volume down + OK first, then hold Power button.
6. Connect USB cable and the program will detect the phone's Com number.
7. Click Start button to download the PIT file to phone.
8. After it is Done Click on Reset button [Partition box should be unchecked automatically - Thanks to jaskir]
9. Click PDA button and select this file: CODE_I9003XXKP7_CL280937_REV08_eng_mid_ship.tar
10. Click PHONE button and select this file: MODEM_I9003XXKP7_REV_00_CL1021949.tar
11. Click BOOTLOADER button and select this file: APBOOT_I9003XXKP7_CL280937_REV08_eng_mid_ship
12. Click CSC button and select this file: GT-I9003-CSC-MULTI-OXAKP7.tar
13: You should unplug usb cable, remove battery, insert battery and bring it back to download mode. I have never been able to bring it to download mode with usb plugged in. [Thanks to jaskir for this suggestion to make it clear to new users!]
14. Click Start button to flash these files to phone.
15. Do not touch anything till you see PASS on the program window.
16. Factory reset
sent from Samsung galaxy S i9003 Remics JB v3