Related
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Note: Before I proceed with this part, Samsung has made it VERY EASY for new users to flash compared to the older ones, Unlike the previous version's that require you to flash it twice or such, or separate files, Their newer releases will always be in this format. With one PDA.md5 file. Unfortunately I cannot keep updating this thread with every region as the flashing methods are exactly the same as follows.
1. Firstly, Download the required firmware from here
2. Run Odin3 v3.04 at the bottom of the page.
3. Set your phone to download mode : Press Volume down + OK first, then hold Power button.
4. Connect your phone, you should see Odin shows your phone is Added with COM number.
5. Extract the contents from the zip, You should have a .dll and a 200-300 MB PDA file.
6. At this point you should see Re-Partition, Auto Reboot and F. Reset Time unchecked.
7. Click PDA button and select the only PDA file in the zip folder (Here you should not touch any of the Re-Partition/F.Reset options as the newer Odin automatically selects it for you, how conveinient!)
8. Click Start button to flash these files to phone.
9. Do not touch anything till you see PASS on the program window.
10. Once you have flashed, after the phone started up, press *#1234# and check your PDA,Phone and CSC, everything should be there. (There should not be any "Unavailable")
11. Factory reset and enjoy
Note: XXKPQ can only be flashed with help from it's supporting predecessor XXKPE like the XXKPN/XXKPH/XXKPM series, So make sure you have XXKPE downloaded. User flashing version varies with this, but this is my successful 100% assured boot.
Note: For those of you receiving WiFi drop issues, Assign a static IP using
Static IP [Download Here], hit the advanced tab and let it auto configure. Credit to [thatguyonfacebookiforgot]
1. Firstly, Download the 2.3.6 firmware from Przekret's thread
2. Run Odin3 v1.83
3. Set your phone to download mode : Press Volume down + OK first, then hold Power button.
4. Connect your phone, you should see Odin shows your phone is Added with COM number.
5. Click PIT button and select this file: latona_20110114.pit
6. You should see Re-Partition, Auto Reboot and F. Reset Time checked.
7. Click PDA button and select this file: CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar
8. Click PHONE button and select this file: MODEM_I9003XXKPE_REV_00_CL1041909.tar
9. Click BOOTLOADER button and select this file: APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar
10. Click CSC button and select this file: GT-I9003-CSC-MULTI-OXAKPE.tar
11. Click Start button to flash these files to phone.
12. Do not touch anything till you see PASS on the program window.
13. Turn off the phone and set it back into download mode once you get an initial first boot to homescreen. Do not set up anything, Just power off and set to download mode.
Note: You only need to flash once to XXKPE before proceeding to XXKPQ
14. In Odin, press Reset button. Re-partition should be unchecked automatically.
15. Select file I9003XXKPQ_I9003XXKPQ_I9003SERKPQ_HOME.tar.md5 as PDA
16. Click on Start to flash XXKPQ PDA to phone
17. Once you have flashed, after the phone started up, press *#1234# and check your PDA,Phone and CSC, everything should ended with KPQ
18. Factory reset and enjoy
Note: XXKPN can only be flashed with help from it's supporting predecessor XXKPE like the XXKPH/XXKPM series, So make sure you have XXKPE downloaded. User flashing version varies with this, but this is my successful 100% assured boot. This firmware is to fix the issues that pertained and caused some WiFi issues for other's
1. Firstly, Download the 2.3.5 firmware from Przekret's thread
2. Run Odin3 v1.83
3. Set your phone to download mode : Press Volume down + OK first, then hold Power button.
4. Connect your phone, you should see Odin shows your phone is Added with COM number.
5. Click PIT button and select this file: latona_20110114.pit
6. You should see Re-Partition, Auto Reboot and F. Reset Time checked.
7. Click PDA button and select this file: CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar
8. Click PHONE button and select this file: MODEM_I9003XXKPE_REV_00_CL1041909.tar
9. Click BOOTLOADER button and select this file: APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar
10. Click CSC button and select this file: GT-I9003-CSC-MULTI-OXAKPE.tar
11. Click Start button to flash these files to phone.
12. Do not touch anything till you see PASS on the program window.
13. Turn off the phone and set it back into download mode once you get an initial first boot to homescreen. Do not set up anything, Just power off and set to download mode.
Note: You only need to flash once to XXKPE before proceeding to XXKPN
14. In Odin, press Reset button. Re-partition should be unchecked automatically.
15. Select file I9003XXKPN_I9003XXKPN_I9003SERKPN_HOME.tar.md5 as PDA
16. Click on Start to flash XXKPN PDA to phone
17. Once you have flashed, after the phone started up, press *#1234# and check your PDA,Phone and CSC, everything should ended with KPN
18. Factory reset and enjoy
Note: XXKPM can only be flashed with help from it's supporting predecessor XXKPE like the XXKPH series, So make sure you have XXKPE downloaded. User flashing version varies with this, but this is my successful 100% assured boot.
1. Firstly, Download the 2.3.5 firmware from Przekret's thread
2. Run Odin3 v1.83
3. Set your phone to download mode : Press Volume down + OK first, then hold Power button.
4. Connect your phone, you should see Odin shows your phone is Added with COM number.
5. Click PIT button and select this file: latona_20110114.pit
6. You should see Re-Partition, Auto Reboot and F. Reset Time checked.
7. Click PDA button and select this file: CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar
8. Click PHONE button and select this file: MODEM_I9003XXKPE_REV_00_CL1041909.tar
9. Click BOOTLOADER button and select this file: APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar
10. Click CSC button and select this file: GT-I9003-CSC-MULTI-OXAKPE.tar
11. Click Start button to flash these files to phone.
12. Do not touch anything till you see PASS on the program window.
13. Turn off the phone and set it back into download mode once you get an initial first boot to homescreen. Do not set up anything, Just power off and set to download mode.
Note: You only need to flash once to XXKPE before proceeding to XXKPM
14. In Odin, press Reset button. Re-partition should be unchecked automatically.
15. Select file I9003XXKPM_I9003XXKPM_I9003SERKPM_HOME.tar.md5 as PDA
16. Click on Start to flash XXKPM PDA to phone
17. Once you have flashed, after the phone started up, press *#1234# and check your PDA,Phone and CSC, everything should ended with KPM
18. Factory reset and enjoy
From Custom ROM's [Must be GINGERBREAD, Not Froyo, I am not responsible if your phone ends in a bootloop from ignorance]:
1. Just flash I9003XXKPM_I9003XXKPM_I9003SERKPM_HOME.tar.md5 in PDA as usual.
2. The phone will end up in a bootloop due to ext4 conversion, Proceed to step 3.
3. Flash Skin's CFRoot in respective PDA.
4. Boot into Custom Recovery via 3 Button Combo.
5. Select option's Wipe Cache and Factory Reset
6. Voila, Enjoy your new easy flashable method.
Note: XXKPH can only be flashed with help from it's supporting predecessor XXKPE, So make sure you have XXKPE downloaded. User flashing version varies with this, but this is my successful 100% assured boot.
1. Firstly, Download the link from spacebar's XXKPH Feedback thread.
2. Run Odin3 v1.83
3. Set your phone to download mode : Press Volume down + OK first, then hold Power button.
4. Connect your phone, you should see Odin shows your phone is Added with COM number.
5. Click PIT button and select this file: latona_20110114.pit
6. You should see Re-Partition, Auto Reboot and F. Reset Time checked.
7. Click PDA button and select this file: CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar
8. Click PHONE button and select this file: MODEM_I9003XXKPE_REV_00_CL1041909.tar
9. Click BOOTLOADER button and select this file: APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar
10. Click CSC button and select this file: GT-I9003-CSC-MULTI-OXAKPE.tar
11. Click Start button to flash these files to phone.
12. Do not touch anything till you see PASS on the program window.
13. Turn off the phone and set it back into download mode once you get an initial first boot to homescreen. Do not set up anything, Just power off and set to download mode.
Note: You only need to flash once to XXKPE before proceeding to XXKPH
14. In Odin, press Reset button. Re-partition should be unchecked automatically.
15. Select file I9003XXKPH_I9003XXKPH_I9003SERKPH_HOME.tar as PDA
16. Click on Start to flash XXKPH PDA to phone
17. Once you have flashed, after the phone started up, press *#1234# and check your PDA,Phone and CSC, everything should ended with KPH
18. Factory reset and enjoy
1. Firstly, Download the link from Krazzy's stock firmware thread.
2. Run Odin3 v1.83
3. Check Re-Partition, Auto Reboot and F. Reset Time.
4. Click PIT button and select this file: latona_20110114.pit
5. Set it to download mode : Press Volume down + OK first, then hold Power button.
6. Connect USB cable and the program will detect the phone's Com number.
7. Click Start button to download the PIT file to phone.
8. After it is Done Click on Reset button [Partition box should be unchecked automatically - Thanks to jaskir]
9. Click PDA button and select this file: CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar
10. Click PHONE button and select this file: MODEM_I9003XXKPE_REV_00_CL1041909.tar
11. Click BOOTLOADER button and select this file: APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar
12. Click CSC button and select this file: GT-I9003-CSC-MULTI-OXAKPE.tar
13: You should unplug usb cable, remove battery, insert battery and bring it back to download mode. I have never been able to bring it to download mode with usb plugged in. [Thanks to jaskir for this suggestion to make it clear to new users!]
14. Click Start button to flash these files to phone.
15. Do not touch anything till you see PASS on the program window.
16. Factory reset
17. [To fix issues that pertain] Reflash from steps 9 -15 again, No need of latona at this point.
1. Make all your backups using TB. Don't forget to move the TB folder to Ext_SD or PC after backing up.
2. Factory reset phone using manual code. (*2767*3855#)
3. Get into recovery mode and wipe all.
4. Now flash the new ROM as usual (latona and then the remaining 4 files.) Be sure not to make any lame errors here.
5. Factory reset again using manual code.
6. Now check to see if the power button functions and the phone reboots when you ask so. (It should work.)
7. Check camera. If you have a black screen, its okay.
8. Factory reset again using manual code.
9. Redo flash procedure again.
10. Factory reset again.
11. Check power button issue and camera. Both should be totally fine.
12. Press power button to lock and leave device for 10 mins. Now, press power button to check if the device wakes up as normal. It should. If you want to avoid the device being woken up by calls or texts or other notifications, just put it into flight mode and turn off Wi-Fi.
13. Root using SuperOneClick. It will show up Kernel Panic error in the end, but its no problem.
14. Just pull battery after that and restart phone. You should see SuperUser installed and working. Upgrade Busybox to 1.18.4 by Stericson.
15. Now install TB and go about your restoring business. DO NOT restore any system apps. Just restore User Apps and data.
16. If you didn't **** up any of the above, you should be up and running 2.3.4 without any issues (yet!).
thanks to spacebar2011 for his version.
1. Firstly, Download the link from Krazzy's stock firmware thread. [Apprently it's been proven recently its 2.3.4 GingerBread and not 2.3.3 ] [Link Below]
2. Run Odin3 v1.83
3. Check Re-Partition, Auto Reboot and F. Reset Time.
4. Click PIT button and select this file: latona_20110114.pit
5. Set it to download mode : Press Volume down + OK first, then hold Power button.
6. Connect USB cable and the program will detect the phone's Com number.
7. Click Start button to download the PIT file to phone.
8. After it is Done Click on Reset button [Partition box should be unchecked automatically - Thanks to jaskir]
9. Click PDA button and select this file: CODE_I9003XXKP7_CL280937_REV08_eng_mid_ship.tar
10. Click PHONE button and select this file: MODEM_I9003XXKP7_REV_00_CL1021949.tar
11. Click BOOTLOADER button and select this file: APBOOT_I9003XXKP7_CL280937_REV08_eng_mid_ship
12. Click CSC button and select this file: GT-I9003-CSC-MULTI-OXAKP7.tar
13: You should unplug usb cable, remove battery, insert battery and bring it back to download mode. I have never been able to bring it to download mode with usb plugged in. [Thanks to jaskir for this suggestion to make it clear to new users!]
14. Click Start button to flash these files to phone.
15. Do not touch anything till you see PASS on the program window.
16. Factory reset
Note: At this point tested and discussed with many users, Update at your own risk, Help will be provided considering it doesn't go off topic.
Also take note, This is a DEV RELEASE, Its bearable. But worth to kill your curiosity over.
KPE Feedback Thread credits go to ephraim
KP9 Feedback Thread credits go to rb210
Falex FAQ on EVERYTHING you need to know about your phone.
DOWNLOAD THE FIRMWARES FROM THIS THREAD : http://forum.xda-developers.com/showthread.php?p=12310841#post12310841
Credit to Krazy for his time and effort in updating the thread. And to everyone in the Gingerbread I9003 Feedback thread.
Notes: I have removed the findings as I have already linked the Feedback threads for the respective firmwares, Please read the feedback to know the problems for the respective GB firmwares.
3:36 Decided to give the thread a whole clean new look
4:20 Added falex FAQ to feedback.
-----------
3:43 Added XXKPH Guide Updated.
------------
7:53 Oct 20, Added XXKPM Guide.
Note : When I have time to download the other azn version's I will write up a guide. Kindly post the firmware ID for which firmware you need a guide.
Dude what is the purpose of making another similar thread related to flashing
kkrraazzyy said:
Dude what is the purpose of making another similar thread related to flashing
Click to expand...
Click to collapse
Too many keep asking about the Bootloader question, So far its a must.
Okk buddy then it is useful for others
kkrraazzyy said:
Okk buddy then it is useful for others
Click to expand...
Click to collapse
Thanks for understanding And for related threads
Hmm mah pleasure dude
revert back
please tell me can we revert back to froyo to claim warranty.
podanimesh said:
please tell me can we revert back to froyo to claim warranty.
Click to expand...
Click to collapse
I think you can flash it back. Just not sure about the bootloader staying the same, Chances are the Froyo's camera and power button wont work. Way to reverse psycho.
Also it should be safe, Anything done in Download Mode can be reversed and changed. But if not in download. Nice paperweight.
Note: Think the warranty only becomes void when you root. Cause thats tampering with system files
Reference to step 8, After it is Done Click on Reset button, then unselect Re-Partition box.
when you click Reset, Re-Partition is automatically unselected
jaskiratsingh said:
Reference to step 8, After it is Done Click on Reset button, then unselect Re-Partition box.
when you click Reset, Re-Partition is automatically unselected
Click to expand...
Click to collapse
Thanks for the update! Appreciate it
kkrraazzyy said:
Hmm mah pleasure dude
Click to expand...
Click to collapse
Did you apply this update? What is your opinion?
Sent from my GT-I9003 using XDA App
jesrani said:
Did you apply this update? What is your opinion?
Sent from my GT-I9003 using XDA App
Click to expand...
Click to collapse
It is quite buggy but fast
Sent from my GT-I9003 using XDA Premium App
sakindia123 said:
It is quite buggy but fast
Sent from my GT-I9003 using XDA Premium App
Click to expand...
Click to collapse
what sort of bugs did you notice?
ritvik93 said:
what sort of bugs did you notice?
Click to expand...
Click to collapse
hangups,random reboots,and power button cant reboot
is this a buggy update
manishnraj said:
is this a buggy update
Click to expand...
Click to collapse
@Mashin Kinda, Its a dev firmware. So its still glitchy but bearable, Since original was supposed to be launched on July/Sept. Depends on regions.
I am in my college and so i havnt flashed it yet but soon will give a try
So far the details as follows:
firmware version:i9003xxkp7
kernel version:2.6.35.7-cl280937
[email protected]#1
build number:gt-i9003-eng 2.3.4 GINGERBRED XXKP7 test-keys.
Could use some feedback @ kkrraazzyy, The current issue is the SOD when boot flashed.
Guys! I live in Argentina and my i9003 is I9003LUBKB1
Do I have to wait to my exactly firmware version? Thanks!!
dieguite said:
Guys! I live in Argentina and my i9003 is I9003LUBKB1
Do I have to wait to my exactly firmware version? Thanks!!
Click to expand...
Click to collapse
Flashing with XXKP7 will be just fine. My orignal is DXKB2 i think but i flashed to XXKB3 with no problems. XXKB3 is a european version but i am from Philippines. I suggest that we should wait for a more stable GB version because this one has a lot of bugs.
Sent from my GT-I9003 using XDA App
my phones gotten much slower than it used to be...the most adventurous ive gotten with my phone was to update it...through kies that is...
so googling my way i got to xda forums...and on the registry i realised that im a total noob!
so i was wondering if anyone here could help me with a step by step procedure of how to root my gti9003 and then help me out with custom ROMs
Dont know if its relevant but the following are my present phone statistics
MODEL:GT-I9003
FIRMWARE: 2.3.6
BASEBAND: I9003DDLE1
KERNEL: 2.6.35.7-CL1153545 [email protected]#1
BUILD NUMBER: GINGERBREAD.DDLF2
ive read a lot on superoneclick and stuff but im not sure if thatll work for my phone.
Thanks
1. flash ddlf2 firmware from her http://www.hotfile.com/dl/161660941/...2_INU.zip.html and password for zip is sampro.pl OR samfirmware
2. then flash cf-root from here http://www.mediafire.com/?0ndawa4g0s851h4 then go to recovery mode by pressing volume up,home button and power button
3. Wipe Data / Factory Reset.
sent from Samsung galaxy S i9003 Remics JB v3
@karanmirchandani96
really appreciate the help..but as i said...im a noob...i couldnt understand much of your reply :/
Fir download the file then
Note: Before I proceed with this part, Samsung has made it VERY EASY for new users to flash compared to the older ones, Unlike the previous version's that require you to flash it twice or such, or separate files, Their newer releases will always be in this format. With one PDA.md5 file. Unfortunately I cannot keep updating this thread with every region as the flashing methods are exactly the same as follows.
1. Firstly, Download the required firmware from here
2. Run Odin3 v3.04 at the bottom of the page.
3. Set your phone to download mode : Press Volume down + OK first, then hold Power button.
4. Connect your phone, you should see Odin shows your phone is Added with COM number.
5. Extract the contents from the zip, You should have a .dll and a 200-300 MB PDA file.
6. At this point you should see Re-Partition, Auto Reboot and F. Reset Time unchecked.
7. Click PDA button and select the only PDA file in the zip folder (Here you should not touch any of the Re-Partition/F.Reset options as the newer Odin automatically selects it for you, how conveinient!)
8. Click Start button to flash these files to phone.
9. Do not touch anything till you see PASS on the program window.
10. Once you have flashed, after the phone started up, press *#1234# and check your PDA,Phone and CSC, everything should be there. (There should not be any "Unavailable")
11. Factory reset and enjoy
Note: XXKPQ can only be flashed with help from it's supporting predecessor XXKPE like the XXKPN/XXKPH/XXKPM series, So make sure you have XXKPE downloaded. User flashing version varies with this, but this is my successful 100% assured boot.
Note: For those of you receiving WiFi drop issues, Assign a static IP using
Static IP [Download Here], hit the advanced tab and let it auto configure. Credit to [thatguyonfacebookiforgot]
1. Firstly, Download the 2.3.6 firmware from Przekret's thread
2. Run Odin3 v1.83
3. Set your phone to download mode : Press Volume down + OK first, then hold Power button.
4. Connect your phone, you should see Odin shows your phone is Added with COM number.
5. Click PIT button and select this file: latona_20110114.pit
6. You should see Re-Partition, Auto Reboot and F. Reset Time checked.
7. Click PDA button and select this file: CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar
8. Click PHONE button and select this file: MODEM_I9003XXKPE_REV_00_CL1041909.tar
9. Click BOOTLOADER button and select this file: APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar
10. Click CSC button and select this file: GT-I9003-CSC-MULTI-OXAKPE.tar
11. Click Start button to flash these files to phone.
12. Do not touch anything till you see PASS on the program window.
13. Turn off the phone and set it back into download mode once you get an initial first boot to homescreen. Do not set up anything, Just power off and set to download mode.
Note: You only need to flash once to XXKPE before proceeding to XXKPQ
14. In Odin, press Reset button. Re-partition should be unchecked automatically.
15. Select file I9003XXKPQ_I9003XXKPQ_I9003SERKPQ_HOME.tar.md5 as PDA
16. Click on Start to flash XXKPQ PDA to phone
17. Once you have flashed, after the phone started up, press *#1234# and check your PDA,Phone and CSC, everything should ended with KPQ
18. Factory reset and enjoy
Note: XXKPN can only be flashed with help from it's supporting predecessor XXKPE like the XXKPH/XXKPM series, So make sure you have XXKPE downloaded. User flashing version varies with this, but this is my successful 100% assured boot. This firmware is to fix the issues that pertained and caused some WiFi issues for other's
1. Firstly, Download the 2.3.5 firmware from Przekret's thread
2. Run Odin3 v1.83
3. Set your phone to download mode : Press Volume down + OK first, then hold Power button.
4. Connect your phone, you should see Odin shows your phone is Added with COM number.
5. Click PIT button and select this file: latona_20110114.pit
6. You should see Re-Partition, Auto Reboot and F. Reset Time checked.
7. Click PDA button and select this file: CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar
8. Click PHONE button and select this file: MODEM_I9003XXKPE_REV_00_CL1041909.tar
9. Click BOOTLOADER button and select this file: APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar
10. Click CSC button and select this file: GT-I9003-CSC-MULTI-OXAKPE.tar
11. Click Start button to flash these files to phone.
12. Do not touch anything till you see PASS on the program window.
13. Turn off the phone and set it back into download mode once you get an initial first boot to homescreen. Do not set up anything, Just power off and set to download mode.
Note: You only need to flash once to XXKPE before proceeding to XXKPN
14. In Odin, press Reset button. Re-partition should be unchecked automatically.
15. Select file I9003XXKPN_I9003XXKPN_I9003SERKPN_HOME.tar.md5 as PDA
16. Click on Start to flash XXKPN PDA to phone
17. Once you have flashed, after the phone started up, press *#1234# and check your PDA,Phone and CSC, everything should ended with KPN
18. Factory reset and enjoy
Note: XXKPM can only be flashed with help from it's supporting predecessor XXKPE like the XXKPH series, So make sure you have XXKPE downloaded. User flashing version varies with this, but this is my successful 100% assured boot.
1. Firstly, Download the 2.3.5 firmware from Przekret's thread
2. Run Odin3 v1.83
3. Set your phone to download mode : Press Volume down + OK first, then hold Power button.
4. Connect your phone, you should see Odin shows your phone is Added with COM number.
5. Click PIT button and select this file: latona_20110114.pit
6. You should see Re-Partition, Auto Reboot and F. Reset Time checked.
7. Click PDA button and select this file: CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar
8. Click PHONE button and select this file: MODEM_I9003XXKPE_REV_00_CL1041909.tar
9. Click BOOTLOADER button and select this file: APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar
10. Click CSC button and select this file: GT-I9003-CSC-MULTI-OXAKPE.tar
11. Click Start button to flash these files to phone.
12. Do not touch anything till you see PASS on the program window.
13. Turn off the phone and set it back into download mode once you get an initial first boot to homescreen. Do not set up anything, Just power off and set to download mode.
Note: You only need to flash once to XXKPE before proceeding to XXKPM
14. In Odin, press Reset button. Re-partition should be unchecked automatically.
15. Select file I9003XXKPM_I9003XXKPM_I9003SERKPM_HOME.tar.md5 as PDA
16. Click on Start to flash XXKPM PDA to phone
17. Once you have flashed, after the phone started up, press *#1234# and check your PDA,Phone and CSC, everything should ended with KPM
18. Factory reset and enjoy
From Custom ROM's [Must be GINGERBREAD, Not Froyo, I am not responsible if your phone ends in a bootloop from ignorance]:
1. Just flash I9003XXKPM_I9003XXKPM_I9003SERKPM_HOME.tar.md5 in PDA as usual.
2. The phone will end up in a bootloop due to ext4 conversion, Proceed to step 3.
3. Flash Skin's CFRoot in respective PDA.
4. Boot into Custom Recovery via 3 Button Combo.
5. Select option's Wipe Cache and Factory Reset
6. Voila, Enjoy your new easy flashable method.
Note: XXKPH can only be flashed with help from it's supporting predecessor XXKPE, So make sure you have XXKPE downloaded. User flashing version varies with this, but this is my successful 100% assured boot.
1. Firstly, Download the link from spacebar's XXKPH Feedback thread.
2. Run Odin3 v1.83
3. Set your phone to download mode : Press Volume down + OK first, then hold Power button.
4. Connect your phone, you should see Odin shows your phone is Added with COM number.
5. Click PIT button and select this file: latona_20110114.pit
6. You should see Re-Partition, Auto Reboot and F. Reset Time checked.
7. Click PDA button and select this file: CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar
8. Click PHONE button and select this file: MODEM_I9003XXKPE_REV_00_CL1041909.tar
9. Click BOOTLOADER button and select this file: APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar
10. Click CSC button and select this file: GT-I9003-CSC-MULTI-OXAKPE.tar
11. Click Start button to flash these files to phone.
12. Do not touch anything till you see PASS on the program window.
13. Turn off the phone and set it back into download mode once you get an initial first boot to homescreen. Do not set up anything, Just power off and set to download mode.
Note: You only need to flash once to XXKPE before proceeding to XXKPH
14. In Odin, press Reset button. Re-partition should be unchecked automatically.
15. Select file I9003XXKPH_I9003XXKPH_I9003SERKPH_HOME.tar as PDA
16. Click on Start to flash XXKPH PDA to phone
17. Once you have flashed, after the phone started up, press *#1234# and check your PDA,Phone and CSC, everything should ended with KPH
18. Factory reset and enjoy
1. Firstly, Download the link from Krazzy's stock firmware thread.
2. Run Odin3 v1.83
3. Check Re-Partition, Auto Reboot and F. Reset Time.
4. Click PIT button and select this file: latona_20110114.pit
5. Set it to download mode : Press Volume down + OK first, then hold Power button.
6. Connect USB cable and the program will detect the phone's Com number.
7. Click Start button to download the PIT file to phone.
8. After it is Done Click on Reset button [Partition box should be unchecked automatically - Thanks to jaskir]
9. Click PDA button and select this file: CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar
10. Click PHONE button and select this file: MODEM_I9003XXKPE_REV_00_CL1041909.tar
11. Click BOOTLOADER button and select this file: APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar
12. Click CSC button and select this file: GT-I9003-CSC-MULTI-OXAKPE.tar
13: You should unplug usb cable, remove battery, insert battery and bring it back to download mode. I have never been able to bring it to download mode with usb plugged in. [Thanks to jaskir for this suggestion to make it clear to new users!]
14. Click Start button to flash these files to phone.
15. Do not touch anything till you see PASS on the program window.
16. Factory reset
17. [To fix issues that pertain] Reflash from steps 9 -15 again, No need of latona at this point.
1. Make all your backups using TB. Don't forget to move the TB folder to Ext_SD or PC after backing up.
2. Factory reset phone using manual code. (*2767*3855#)
3. Get into recovery mode and wipe all.
4. Now flash the new ROM as usual (latona and then the remaining 4 files.) Be sure not to make any lame errors here.
5. Factory reset again using manual code.
6. Now check to see if the power button functions and the phone reboots when you ask so. (It should work.)
7. Check camera. If you have a black screen, its okay.
8. Factory reset again using manual code.
9. Redo flash procedure again.
10. Factory reset again.
11. Check power button issue and camera. Both should be totally fine.
12. Press power button to lock and leave device for 10 mins. Now, press power button to check if the device wakes up as normal. It should. If you want to avoid the device being woken up by calls or texts or other notifications, just put it into flight mode and turn off Wi-Fi.
13. Root using SuperOneClick. It will show up Kernel Panic error in the end, but its no problem.
14. Just pull battery after that and restart phone. You should see SuperUser installed and working. Upgrade Busybox to 1.18.4 by Stericson.
15. Now install TB and go about your restoring business. DO NOT restore any system apps. Just restore User Apps and data.
16. If you didn't **** up any of the above, you should be up and running 2.3.4 without any issues (yet!).
thanks to spacebar2011 for his version.
1. Firstly, Download the link from Krazzy's stock firmware thread. [Apprently it's been proven recently its 2.3.4 GingerBread and not 2.3.3 ] [Link Below]
2. Run Odin3 v1.83
3. Check Re-Partition, Auto Reboot and F. Reset Time.
4. Click PIT button and select this file: latona_20110114.pit
5. Set it to download mode : Press Volume down + OK first, then hold Power button.
6. Connect USB cable and the program will detect the phone's Com number.
7. Click Start button to download the PIT file to phone.
8. After it is Done Click on Reset button [Partition box should be unchecked automatically - Thanks to jaskir]
9. Click PDA button and select this file: CODE_I9003XXKP7_CL280937_REV08_eng_mid_ship.tar
10. Click PHONE button and select this file: MODEM_I9003XXKP7_REV_00_CL1021949.tar
11. Click BOOTLOADER button and select this file: APBOOT_I9003XXKP7_CL280937_REV08_eng_mid_ship
12. Click CSC button and select this file: GT-I9003-CSC-MULTI-OXAKP7.tar
13: You should unplug usb cable, remove battery, insert battery and bring it back to download mode. I have never been able to bring it to download mode with usb plugged in. [Thanks to jaskir for this suggestion to make it clear to new users!]
14. Click Start button to flash these files to phone.
15. Do not touch anything till you see PASS on the program window.
16. Factory reset
sent from Samsung galaxy S i9003 Remics JB v3
Hi all i tried to flash i9003 galaxy SL from steps below to 2.3.6 , but the firmware zip file does not have MODEM, CSC and PDA files but only .dll file and tar.md5 file, where can i get the MODEM, CSC and PDA.
I download the firmwares from link below:-
http://www.tsar3000.com/Joomla/inde...alaxy-sl-firmwares&catid=55:samsung&Itemid=82
Firmware Update Steps:
Run Samsung I9003 Galaxy SL Downloader.
Check Re-Partition, Auto Reboot and F. Reset Time.
Click PIT button and select this file: latona_20110114.pit
Put your phone into download mode: Press Volume down + OK + Power.
Connect USB cable and the program will detect the phone's Com number.
Click Start button to download the PIT file to phone.
After it is Done Click on Reset button, then unselect Re-Partition box.
Click PDA button and select this file: I9003xxxxx-xxx...-PDA-low-CL890053.tar.md5 <<<<<<<<<<<<<<<
Click PHONE button and select this file: MODEM_I9003xxxxx_REV_00_CL889972.tar.md5 <<<<<<<<<<<<<<<<<
Click CSC button and select this file: GT-I9003-CSC-xxxxxx.tar.md5 <<<<<<<<<<<<<<<<<<<
Remove the battery, then enter Device into Download Mode again.
Click Start button to flash these files to phone.
Do not touch anything till you see PASS on the program window.
Do full reset by this Code: *2767*3855#.wares i download dont have CSC , PDA
suhailpuri said:
Hi all i tried to flash i9003 galaxy SL from steps below to 2.3.6 , but the firmware zip file does not have MODEM, CSC and PDA files but only .dll file and tar.md5 file, where can i get the MODEM, CSC and PDA.
I download the firmwares from link below:-
http://www.tsar3000.com/Joomla/inde...alaxy-sl-firmwares&catid=55:samsung&Itemid=82
Firmware Update Steps:
Run Samsung I9003 Galaxy SL Downloader.
Check Re-Partition, Auto Reboot and F. Reset Time.
Click PIT button and select this file: latona_20110114.pit
Put your phone into download mode: Press Volume down + OK + Power.
Connect USB cable and the program will detect the phone's Com number.
Click Start button to download the PIT file to phone.
After it is Done Click on Reset button, then unselect Re-Partition box.
Click PDA button and select this file: I9003xxxxx-xxx...-PDA-low-CL890053.tar.md5 <<<<<<<<<<<<<<<
Click PHONE button and select this file: MODEM_I9003xxxxx_REV_00_CL889972.tar.md5 <<<<<<<<<<<<<<<<<
Click CSC button and select this file: GT-I9003-CSC-xxxxxx.tar.md5 <<<<<<<<<<<<<<<<<<<
Remove the battery, then enter Device into Download Mode again.
Click Start button to flash these files to phone.
Do not touch anything till you see PASS on the program window.
Do full reset by this Code: *2767*3855#.wares i download dont have CSC , PDA
Click to expand...
Click to collapse
First of all post in the general section. Second, read a lot.
Thirdly, which firmware are you at present? If KPE, flash LF2. The new stock firmwares only have a single .tar file. No modem, csc or any other files needed. And download from here >> http://forum.xda-developers.com/showthread.php?t=1004647/
nbrian2012 said:
First of all post in the general section. Second, read a lot.
Thirdly, which firmware are you at present? If KPE, flash LF2. The new stock firmwares only have a single .tar file. No modem, csc or any other files needed. And download from here >> http://forum.xda-developers.com/showthread.php?t=1004647/
Click to expand...
Click to collapse
i dont know the firmware as the phone is bricked, i managed to get into firmware download mode but it gives me an error after flashing, i flash the pit file and then reset odin and then enter download mode again and select single firmware file and check PDA option but flashing fale.
What file do i download because i downloaded many firmwares gingerbread ones but they all have one single tar file.
Socon off all what box do i need to select if i am flashing a single file , PDA or phone or CSC.
Suhail
suhailpuri said:
i dont know the firmware as the phone is bricked, i managed to get into firmware download mode but it gives me an error after flashing, i flash the pit file and then reset odin and then enter download mode again and select single firmware file and check PDA option but flashing fale.
What file do i download because i downloaded many firmwares gingerbread ones but they all have one single tar file.
Socon off all what box do i need to select if i am flashing a single file , PDA or phone or CSC.
Suhail
Click to expand...
Click to collapse
Download KPE, the files from the link I gave you ^
and follow THIS guide carefully >>>
Misledz said:
2. Run Odin3 v1.83
3. Check Re-Partition, Auto Reboot and F. Reset Time.
4. Click PIT button and select this file: latona_20110114.pit
5. Set it to download mode : Press Volume down + OK first, then hold Power button.
6. Connect USB cable and the program will detect the phone's Com number.
7. Click Start button to download the PIT file to phone.
8. After it is Done Click on Reset button [Partition box should be unchecked automatically - Thanks to jaskir]
9. Click PDA button and select this file: CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar
10. Click PHONE button and select this file: MODEM_I9003XXKPE_REV_00_CL1041909.tar
11. Click BOOTLOADER button and select this file: APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar
12. Click CSC button and select this file: GT-I9003-CSC-MULTI-OXAKPE.tar
13: You should unplug usb cable, remove battery, insert battery and bring it back to download mode. I have never been able to bring it to download mode with usb plugged in. [Thanks to jaskir for this suggestion to make it clear to new users!]
14. Click Start button to flash these files to phone.
15. Do not touch anything till you see PASS on the program window.
16. Factory reset
17. [To fix issues that pertain] Reflash from steps 9 -15 again, No need of latona at this point.
Click to expand...
Click to collapse
Must you have any issue at any point, reply again.
The SL can never get bricked unless you flash a firmware not compatible with it
Sent from my Galaxy Nexus using Tapatalk 4 Beta
How can i flash a single file .tar.md5 with odin, becuause now all the firmwares come with a single file i.e. .tar.md5 unlike old firmwares have CSC, modem and PDA file
shall i put pit file first and then flash which option needs to be checked ?
This has become really confusing for me now.
Can i also put my phone in download mode and flash via KIES ?
Thanks in advance,
Suhail
suhailpuri said:
i dont know the firmware as the phone is bricked, i managed to get into firmware download mode but it gives me an error after flashing, i flash the pit file and then reset odin and then enter download mode again and select single firmware file and check PDA option but flashing fale.
What file do i download because i downloaded many firmwares gingerbread ones but they all have one single tar file.
Socon off all what box do i need to select if i am flashing a single file , PDA or phone or CSC.
Suhail
Click to expand...
Click to collapse
HELP NEEDED TO FLASH FIRMWARE IN SAMSUNG GALAXY SL GT-I9003
I have downloaded the firmwares suggested by you... Its not clear how to proceed with the flashing of the firmware, as the steps asked to perform by you are contradicting to your previous post -> As there is only only file i.e GT-I9003_XEO_I9003XWLF2_I9003OXXLF1_I9003XXLE4 and rest of the files i.e PHONE file: MODEM_I9003XXKPE_REV_00_CL1041909.tar, BOOTLOADER file: APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar, CSC file: GT-I9003-CSC-MULTI-OXAKPE.tar are not required. Please be specific what is to be done to complete the flashing procedure.
well i just wanna know how to flash with odin when you have one file for firmware and tutorials show 3 files, but whatever firmwares i download they all have one ta file and no 3 files as suggeted in tutorials.
Suhail
Flash first clean for mandatory starting
On CM10 Alpha 3 and all other basic Froyo, Gingerbread, ICS, JB
- drivers samsung.rar - 5.58 MB
- Open Odin 1.85 only !!!
- KPE FULL (do not forget the PIT) (Froyo only ! no forget bootloader)
reset odin then remove cable and battery after samsung logo
- LF2 (PDA only with Odin)
reset odin then remove cable and battery after second samsung logo
- CF Root LF2 (PDA only with Odin)
I followed all steps, but in STEP 2 when i download the file its iso and not not md5 or tar so i dont know how to proceed and flash it, i tried to mount it , burn it no sucess
Anyways i went to step 3 and flashed again, but phone gets stuck at boot screen samsung logo
Any
UNZIP ?§!
suhailpuri said:
I followed all steps, but in STEP 2 when i download the file its iso and not not md5 or tar so i dont know how to proceed and flash it, i tried to mount it , burn it no sucess
Anyways i went to step 3 and flashed again, but phone gets stuck at boot screen samsung logo
Any
Click to expand...
Click to collapse
Dude, if it's a zip file then extract it & use the file which is extracted.
Good luck!
Sent from my GT-I9003.
LoLaTiOn said:
UNZIP ?§!
Click to expand...
Click to collapse
Hi LoLaTiOn,
I have unzipped the CSROOT file, what I could see was a .img file where as while selecting the file in the ODin 1.85 it demands for a .tar file. Can you please further help in this and pass me the link for the actual file i.e CSROOTXXXXXXXX.tar file in the required format to flash the Android OS.
Rest all the files in the link provided by you are in the required format.
Siddhant Shankpal said:
Dude, if it's a zip file then extract it & use the file which is extracted.
Good luck!
Sent from my GT-I9003.
Click to expand...
Click to collapse
Hi Siddhant,
Anybody in the world knows that we have to unzip a zipped file before using it. The actual problem is that --> After unzipping the file , I see a .img file where as Odin requires a .tar file to flash the Android OS. I tried converting it into a .tar file by using a cygwin terminal but no luck. I also tried searching for the same file in other links (Websites) but still there was no luck.
Can you give a hand to help me out.
suhailpuri said:
Hi Siddhant,
Anybody in the world knows that we have to unzip a zipped file before using it. The actual problem is that --> After unzipping the file , I see a .img file where as Odin requires a .tar file to flash the Android OS. I tried converting it into a .tar file by using a cygwin terminal but no luck. I also tried searching for the same file in other links (Websites) but still there was no luck.
Can you give a hand to help me out.
Click to expand...
Click to collapse
U mentioned "step 2" that means u were stuck in DDLF2 flashing step. But now ur telling "CFROOT LF2" step.
Okay, now in this step u don't need to unzip this file & just flash it from odin as in PDA section.
But I hope ur able to boot into ur phone after flashing DDLF2 firmware.
Good luck!
Sent from my GT-I9003.
Siddhant Shankpal said:
U mentioned "step 2" that means u were stuck in DDLF2 flashing step. But now ur telling "CFROOT LF2" step.
Okay, now in this step u don't need to unzip this file & just flash it from odin as in PDA section.
But I hope ur able to boot into ur phone after flashing DDLF2 firmware.
Good luck!
Sent from my GT-I9003.
Click to expand...
Click to collapse
My bad, I have mentioned it earlier that I have tried flashing the same .img file in the entire process but no luck.
suhailpuri said:
My bad, I have mentioned it earlier that I have tried flashing the same .img file in the entire process but no luck.
Click to expand...
Click to collapse
Download this DDLF2 firmware & extract it. http://forum.xda-developers.com/showthread.php?t=2329200
1. After extracting, switch off your phone & go to download mode.
2. Open odin 1.85 on ur PC & connect ur phone to ur PC. Check, whether it is connected by the yellow signal.
3. First only flash .pit file from the extracted folder. Then remove battery & put it back then again go download mode.
4. Browse & select all respected files from the extracted folder. (Do not include bootloader file if ur coming back to stock from CM 10 based roms.)
5. Click start.
Good luck!
Sent from my GT-I9003.
Hello,
I am trying to update my phone( Samsung Galaxy SL I9003) to Jelly Bean by following the steps mentioned in the site below
http://www.sproductions.in/2013/06/how-to-install-jelly-bean-422-on.html
I completed the first step successfully. However the second step asks me to select an option named "Install Zip from sd card". But I do not have this option.
I searched little bit for the solution and found the following url.
http://forum.xda-developers.com/showthread.php?t=1351056
But i have hard time following the solution mentioned. There are no steps given.
So could you please help me with this.
Thanks in advance,
Arjun
Hello All,
I got the steps from the below link
http://forum.xda-developers.com/showthread.php?t=1151704
Now i can see the option.
Thank You,
install latest bam kernel!
Sent from my GT-I9003 using xda app-developers app
CM10.1 Alpha 2????????????
hey A8 in out now and every thing is working
don't follow other site...every thing you need is here:
download full DDLF2 from here (thanks to sgatechwork)
follow these instructions (thanks to Misledz):
2. Run Odin3 v1.83
3. Set your phone to download mode : Press Volume down + OK first, then hold Power button.
4. Connect your phone, you should see Odin shows your phone is Added with COM number.
5. Click PIT button and select this file: latona_20110114.pit
6. You should see Re-Partition, Auto Reboot and F. Reset Time checked.
7. Click PDA button and select this file: CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar
8. Click PHONE button and select this file: MODEM_I9003XXKPE_REV_00_CL1041909.tar
9. Click BOOTLOADER button and select this file: APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar
10. Click CSC button and select this file: GT-I9003-CSC-MULTI-OXAKPE.tar
11. Click Start button to flash these files to phone.
12. Do not touch anything till you see PASS on the program window.
13. Turn off the phone and set it back into download mode once you get an initial first boot to homescreen. Do not set up anything, Just power off and set to download mode.
Note: You only need to flash once to XXKPE before proceeding to XXKPQ
14. In Odin, press Reset button. Re-partition should be unchecked automatically.
15. Select file I9003XXKPQ_I9003XXKPQ_I9003SERKPQ_HOME.tar.md5 as PDA
16. Click on Start to flash XXKPQ PDA to phone
17. Once you have flashed, after the phone started up, press *#1234# and check your PDA,Phone and CSC, everything should ended with KPQ
18. Factory reset and enjoy
now root your phone using bam kernel (PDA_BCK_CF-root_universal_beta15.tar) as PDA in download mode using odin3 v1.85 only (thanks to XDA-Bam)
then download any JB rom you want and follow the OP instructions to install it
Your dreams are now reality!
You can install Nougat easily on your Galaxy s7 edge!!
1)Download Odin 3.12.3 .zip file and run/open Odin3 v3.12.3.exe file from the extracted files on your PC.
2)Download the Nougat firmware for your device from the downloads section above, and unzip the .zip file to get the files starting with AP, CSC, Home_CSC, BL and CP in the beginning of their name.
3)Enable OEM unlock on your phone:
Go to Settings » About phone » and tap Build number seven times to enable Developer options.
4)Go back to main Settings page, scroll to bottom and select Developer options from there.
Under Developer options, look for Enable OEM unlock checkbox/toggle and enable it.
5) Boot your device into Download mode:
Switch off your device.
Press and hold “Home + Power + Volume down” buttons for a few seconds until you see a warning screen.
Press Volume Up on the warning screen to accept it and boot into Download mode.
6) Once your device is in download mode, connect it to the PC with a USB cable. The Odin window on PC should detect the device and show an “Added!!” message.
7) Now we’ll select each firmware file (from files we got in Step 2 above) into the appropriate box in Odin.
Click on CSC tab and select the firmware file starting with HOME_CSC in its name.
└ Note: Do NOT select the regular CSC file that starts with CSC in its name, as that would replace your CSC and thus would result factory data reset of the device.
Click on CP tab and select file starting with CP in its name.
Click on BL tab and select the file starting with BL in its name.
Click on AP tab and select the file starting with AP in its name.
└ Note: DON’T play with any other options on Odin the screen. You’re only required to connect your device and select the firmware files as instructed above.
Click the Start button on Odin and wait for it to finish the process. Once it has finished successfully, you’ll see a pass message on the Odin screen.
8) Your device will automatically reboot when Odin is done flashing. You can then disconnect your device.
└ It might take some time for the first boot after flashing a stock firmware.
That’s it. Your Galaxy S7/Galaxy S7 Edge is now rocking Android Nougat update.
9) enjoy
-------------
download section
-------------
Odin : http://www.theandroidsoul.com/download-odin/
firmware : http://downloadmirror.co/1KtK/G935FXXU1ZPK4-thanks-samfirm.net.zip
Source : http://www.theandroidsoul.com/download-galaxy-s7-and-s7-edge-nougat-firmware-odin-tar/
Thanks, but there are already multiple discussions on this.
EG the dedicated Nougat thread: https://forum.xda-developers.com/s7-edge/how-to/android-7-0-s7-edge-uk-beta-program-apk-t3493696