Related
Guys, wondering if someone could give me some direction to restoring my TF101 to working conditions.
I have a rooted TF101 that was running 9.1.2.27.
This setup has been running great since .27 (not done OTA, Found here) came out, so I haven't bothered upgrading recently.
Fast forward to this week and it seems the Tablet started locking up at some point in the last couple days I hadn't used it. This would cause a battery drain until the device turned off. Upon rebooting I could get into the OS for maybe a minute before it would freeze again.
I decided to wipe the device, I went into CWM Recovery and wiped all caches and then tried to wipe all data/factory reset. It is at this time I get the following error:
Error removing /data/data/com.android.browser/databases/webview.db-wal!Error formatting /data!
Try starting back up and get a boot loop.
Upon reflashing the ROM, I find the TF101 in constant boot loop not making it 8 seconds into the bootup before rebooting.
I can still get into recovery so I try various kernels and roms with no success. Through searching I find CWM 6.0.1.4 and load it. Everything loads normally and I can now wipe data/factory reset, wipe all Cache even format all parts. I try to flash every ROM I can get my hands on from stock to older roms that I have ran succesfully to EOS Nighties, Every rom goes into Boot Loop after about 10 seconds.
Any Idea on where to go from here? I have been reading threads for hours now with no solution.
MODS: Putting in DEV since this is a Rooted TF, but if this should go to Q&A please move
This question should be in the QA section...
But your stock ROM was ICS and the newest EOS nightlies are based on JB which have different partitions. If you flash back and forth with ICS and JB you could be running into problems there.
Have you tried the option in CWM called "Fix Permissions"? This is supposed to reset the permissions correctly for the system apps area I believe which helped a lot of people with force close issues. It's worth a shot.
Are you installing ROM's from external SD card or the Internal SD card? That shouldn't matter but I have always stuck with the External SD card.
One thing you could also try is to wipe the big 3 several times a piece before installing the ROM. I found it had made some ROM's load better when I encountered a few issues. Also, stick with one ROM either ICS or JB. Going back and forth will cause problems.
Also, I remember that from ICS to JB, some ROM's required the ROM to be installed twice literally after it installs install it again or some ROM's may reboot themselves back into recovery to complete the install.
Try that with the ROM you pick to get things back on track.
There is also some "Super Wipe" scripts floating around but I believe they were for a specific ROM and I think it was ICS based. You should be able to search XDA for that here in the Dev section.
TomTcom said:
This question should be in the QA section...
But your stock ROM was ICS and the newest EOS nightlies are based on JB which have different partitions. If you flash back and forth with ICS and JB you could be running into problems there.
Have you tried the option in CWM called "Fix Permissions"? This is supposed to reset the permissions correctly for the system apps area I believe which helped a lot of people with force close issues. It's worth a shot.
Are you installing ROM's from external SD card or the Internal SD card? That shouldn't matter but I have always stuck with the External SD card.
One thing you could also try is to wipe the big 3 several times a piece before installing the ROM. I found it had made some ROM's load better when I encountered a few issues. Also, stick with one ROM either ICS or JB. Going back and forth will cause problems.
Also, I remember that from ICS to JB, some ROM's required the ROM to be installed twice literally after it installs install it again or some ROM's may reboot themselves back into recovery to complete the install.
Try that with the ROM you pick to get things back on track.
There is also some "Super Wipe" scripts floating around but I believe they were for a specific ROM and I think it was ICS based. You should be able to search XDA for that here in the Dev section.
Click to expand...
Click to collapse
The ICS to JB isn't the issue as the issue started happening randomly with a ICS Rom that has been working for 4+ months when it has never had anything put ICS (well HC when I got it last year). Trying the JB rom was a near last ditch effort
I tried Revolutions superwipe several times, didn't help.
I probably completely screwed it up now in frustration. Tried to load the stock rom and now Recovery is screwed and it is boot loop so I don't think I can connect it to the computer now.
Hosed you think?
So now the question is, with a Tab that won't stay on longer then 8 seconds and no longer has a recovery, is there any other hope? I'm guessing bricked.
Firehawkns said:
So now the question is, with a Tab that won't stay on longer then 8 seconds and no longer has a recovery, is there any other hope? I'm guessing bricked.
Click to expand...
Click to collapse
You held down pwr + volume down when turning on and no text appears at the top left?
If not follow this thread
http://forum.xda-developers.com/showthread.php?t=1688012&highlight=nvflash
or http://forum.xda-developers.com/showthread.php?t=1688447&highlight=bootloop
Firehawkns said:
Guys, wondering if someone could give me some direction to restoring my TF101 to working conditions.
I have a rooted TF101 that was running 9.1.2.27.
This setup has been running great since .27 (not done OTA, Found here) came out, so I haven't bothered upgrading recently.
Fast forward to this week and it seems the Tablet started locking up at some point in the last couple days I hadn't used it. This would cause a battery drain until the device turned off. Upon rebooting I could get into the OS for maybe a minute before it would freeze again.
I decided to wipe the device, I went into CWM Recovery and wiped all caches and then tried to wipe all data/factory reset. It is at this time I get the following error:
Error removing /data/data/com.android.browser/databases/webview.db-wal!Error formatting /data!
Try starting back up and get a boot loop.
Upon reflashing the ROM, I find the TF101 in constant boot loop not making it 8 seconds into the bootup before rebooting.
I can still get into recovery so I try various kernels and roms with no success. Through searching I find CWM 6.0.1.4 and load it. Everything loads normally and I can now wipe data/factory reset, wipe all Cache even format all parts. I try to flash every ROM I can get my hands on from stock to older roms that I have ran succesfully to EOS Nighties, Every rom goes into Boot Loop after about 10 seconds.
Any Idea on where to go from here? I have been reading threads for hours now with no solution.
MODS: Putting in DEV since this is a Rooted TF, but if this should go to Q&A please move
Click to expand...
Click to collapse
Try using NV flash to go back to stock if you can get into APX mode.
Sent from my DROID RAZR HD using xda premium
morphuex said:
You held down pwr + volume down when turning on and no text appears at the top left?
If not follow this thread
http://forum.xda-developers.com/showthread.php?t=1688012&highlight=nvflash
or http://forum.xda-developers.com/showthread.php?t=1688447&highlight=bootloop
Click to expand...
Click to collapse
Yea, I can do the power + vol down and then up and get the recovery android guy, then he goes on his back and a red exclamation comes up (which I believe means no recovery mode installed
I can also do the pwr + vol down and then wait 5 seconds and get the wipe device or android options, but it won't let me choose anything, 10 seconds later it reboots.
clouse2013 said:
Try using NV flash to go back to stock if you can get into APX mode.
Sent from my DROID RAZR HD using xda premium
Click to expand...
Click to collapse
Will try tonight, but I believe all of those involve the computer having time to recognize the device, which it doesn't stay on long enough for the computer to recognize is and it won't seem to connect USB when the android guy is up.
nice rom! going to check this out tonight, thanks!
So I got into APX mode, windows shows no drivers, but it does show in devices. Trying NVFLash it says it is doing something, but nothing on the TF changes. Is there another step I am missing?
Firehawkns said:
So I got into APX mode, windows shows no drivers, but it does show in devices. Trying NVFLash it says it is doing something, but nothing on the TF changes. Is there another step I am missing?
Click to expand...
Click to collapse
Have a search for universal naked driver in the dev section, that should sort the drivers out I believe then you should be good to go.
---------- Post added at 10:37 PM ---------- Previous post was at 10:34 PM ----------
http://forum.xda-developers.com/showthread.php?t=1514942&highlight=naked+driver
There you go
pops106 said:
Have a search for universal naked driver in the dev section, that should sort the drivers out I believe then you should be good to go.
---------- Post added at 10:37 PM ---------- Previous post was at 10:34 PM ----------
http://forum.xda-developers.com/showthread.php?t=1514942&highlight=naked+driver
There you go
Click to expand...
Click to collapse
Thanks for the info, truly! I had searched for Drivers, but not naked.
That worked and it allowed me to use Easyflasher to get CWM back on.
Now I am back where I started, I have tried loading several Roms. Everyone hangs up about 15 seconds into first boot while the setup splash screen is on (for example the dotted circle on stock Asus rom or the simon says color circle like the JB rom or what ever it was in the ICS rom I was using. Something in the tab is stopping it from booting on up.
But I can now format everything and wipe data. I can connect APX mode. Anything else I can try from there. Starting to seem like something Hardware is busted.
Firehawkns said:
Something in the tab is stopping it from booting on up.
But I can now format everything and wipe data. I can connect APX mode. Anything else I can try from there. Starting to seem like something Hardware is busted.
Click to expand...
Click to collapse
Did you fix permissions while you were in recovery? It's a long shot but that may help. You may have a folder that's chmod'ed incorrectly. If so that'll prevent the system from being able to write or read to that folder making it impossible to install to, or run from it. Fix permissions, re-flash and reboot.
I know TomTcom mentioned it already. I don't see if you tried it in your replies though.
grgmre said:
Did you fix permissions while you were in recovery? It's a long shot but that may help. You may have a folder that's chmod'ed incorrectly. If so that'll prevent the system from being able to write or read to that folder making it impossible to install to, or run from it. Fix permissions, re-flash and reboot.
I know TomTcom mentioned it already. I don't see if you tried it in your replies though.
Click to expand...
Click to collapse
Yea, I tried that first. Sorry forgot to mention.
Are you able to flash the stock firmware using Easyflasher?
cabraswell said:
Are you able to flash the stock firmware using Easyflasher?
Click to expand...
Click to collapse
yes, I am able to flash to stock rom I got from Asus and the one I took for Rooted with stock on the forum. The flash, and it gives you the initial progress bar on first boot, then reboots at the end of the progress bar and goes to the Asus with the moving circles for about 5 seconds then keeps rebooting from there.
In a PC world I would wonder Ram issues, Over heating, or insuffecent power supply at this point. Not sure what to think here.
Is there a way to use TWOP and delete everything you see on the system and then reflash?
Firehawkns said:
yes, I am able to flash to stock rom I got from Asus and the one I took for Rooted with stock on the forum. The flash, and it gives you the initial progress bar on first boot, then reboots at the end of the progress bar and goes to the Asus with the moving circles for about 5 seconds then keeps rebooting from there.
In a PC world I would wonder Ram issues, Over heating, or insuffecent power supply at this point. Not sure what to think here.
Is there a way to use TWRP and delete everything you see on the system and then reflash?
Click to expand...
Click to collapse
In Addition, I have tried several times using TWRP to format Data and it fails. Could this be a clue?
Firehawkns said:
In Addition, I have tried several times using TWRP to format Data and it fails. Could this be a clue?
Click to expand...
Click to collapse
Have you tried using nvflash that blasts everything, takes you back to as clean as clean can be.
I am starting to think hardware though but if you can sit in recovery of adb / apx mode without issue then maybe it is a software thing.
No probs wiith the drivers by the way, its not really the right website for searching for the word naked.... dam don't can't won't imagine what you could of found with the members in here...
SUCCESS!!
I am not totally sure what finally worked as I just kept trying to reset/wipe/format/ and reflash, but this last time finally worked it seems. I have the stock Asus rom back on and going through setup.
I do find that if I try to put EOS on it just sits at the color things that show loading and never moves forward, so I just put the stock rom back on for now. Try to get Root back on for Titanium backup and enjoy the tablet again and worry about JB later maybe.
Firehawkns said:
SUCCESS!!
I am not totally sure what finally worked as I just kept trying to reset/wipe/format/ and reflash, but this last time finally worked it seems. I have the stock Asus rom back on and going through setup.
I do find that if I try to put EOS on it just sits at the color things that show loading and never moves forward, so I just put the stock rom back on for now. Try to get Root back on for Titanium backup and enjoy the tablet again and worry about JB later maybe.
Click to expand...
Click to collapse
I'm glad you finally got it fixed. I had some issues a while back (two weeks after I bought it) and I panicked and caused more trouble. Finally after stepping away from it for a day or two and a wife encouraging me I was able to get it going again...but my gut was in knots for that day or two.
Tablet after redoing the original root does not go over the system.
Not have access to ADB DEVICE or by Windows or the Linux Ubuntu, no longer accepts update totally blocked.
Ask help for those who have been through this problem.
Hi everyone, hate for my first to be a call for assistance, but here goes. Bought an Asus tf300t earlier today. I unlocked the device, then attempted to begin walking through this guide(http://forum.xda-developers.com/showthread.php?t=1845377) in order to have root+jb. In order to install clockworkmod, set up fastboot. After getting an error of "cannot load" in fasboot for the recovery image, I gave up, used the cmd prompt to reboot the device. On reboot, the touch screen no longer responded. I went to recovery, wiped data, to no avail. Now its simply showing the welcome screen, where you choose english, but can't select start. I've rebooted, wiped, and swore. A lot. My OS is windows 7, if that helps. Thanks everyone.
Shourisha1 said:
Hi everyone, hate for my first to be a call for assistance, but here goes. Bought an Asus tf300t earlier today. I unlocked the device, then attempted to begin walking through this guide(http://forum.xda-developers.com/showthread.php?t=1845377) in order to have root+jb. In order to install clockworkmod, set up fastboot. After getting an error of "cannot load" in fasboot for the recovery image, I gave up, used the cmd prompt to reboot the device. On reboot, the touch screen no longer responded. I went to recovery, wiped data, to no avail. Now its simply showing the welcome screen, where you choose english, but can't select start. I've rebooted, wiped, and swore. A lot. My OS is windows 7, if that helps. Thanks everyone.
Click to expand...
Click to collapse
Do I understand correctly that you've never successfully installed a custom recovery on your tab? So how did you wipe data? You chose the fourth option in the stock recovery?
graphdarnell said:
Do I understand correctly that you've never successfully installed a custom recovery on your tab? So how did you wipe data? You chose the fourth option in the stock recovery?
Click to expand...
Click to collapse
There were only 3 options--Wipe Data, usb, and android. I'd had success rooting the tablet earlier, but believed I'd made an error somewhere so followed that guide to try and begin again from the beginning. The wipe wasn't what caused the issue. It was working fine, until the reboot using the cmd line. Thats what makes so little sense to me.
Shourisha1 said:
There were only 3 options--Wipe Data, usb, and android. I'd had success rooting the tablet earlier, but believed I'd made an error somewhere so followed that guide to try and begin again from the beginning. The wipe wasn't what caused the issue. It was working fine, until the reboot using the cmd line. Thats what makes so little sense to me.
Click to expand...
Click to collapse
You didn't have the RCK option on your recovery? You said the wipe wasn't the culprit and it was working fine. Did you get to reboot the tab successfully after the wipe? Now everything seems to work fine on your PC monitor doesn't mean it is so. Lots of people using NVflash derivatives witness a smooth transition on papers until they find out it isn't so. Reboot command from ADB doesn't do anything special. I can't think of it doing any damage to the firmware if successfully installed earlier.
graphdarnell said:
You didn't have the RCK option on your recovery? You said the wipe wasn't the culprit and it was working fine. Did you get to reboot the tab successfully after the wipe? Now everything seems to work fine on your PC monitor doesn't mean it is so. Lots of people using NVflash derivatives witness a smooth transition on papers until they find out it isn't so. Reboot command from ADB doesn't do anything special. I can't think of it doing any damage to the firmware if successfully installed earlier.
Click to expand...
Click to collapse
Uhm, well, its simply started registering touch again. Like nothing had happened. Makes me worry about the tablet itself. But, its working fine now, and I didn't do a thing. Sigh. I'm not sure. Not I just have to figure out why fastbooter keeps giving me the "cannot load recovery.img" error. Thanks for the help!
Sounds like you are on the old bootloader. Be careful about wiping.
I'd update to the latest Asus Stock ROM for your device from their website which will bring you up to the latest bootloader.
Alright, I hate being that guy. You know, the one who posts the same question as 50 other people because he is too lazy to search. But in my defense, I have spent the last three days pouring over thread after thread and still can't find the answer, so please be patient and gimme a break!
So, I'm stuck in CWM 5.8.3.4 loop after flashing Katkiss and not knowing I couldn't use the "boot to recovery" option. I've got no access to my micro SD card and my x64 Win 7 won't recognize the TF101 so I can't put my own recover zip on. Cold boot goes to the screen that lets me boot Android or Wipe. If I pick Android, it hangs (for hours). I've wiped everything and reinstalled Katkiss, Revolver, Revolution, but I have the same problems.
Is there a thread that starts from the BEGINNING of the fix and sees it through? I've found dozens of threads that say, "Just input (code), flash, and you're done!", but I guess I'm not that far along. I've bricked Dinc/Dinc2, Razrs, etc., but never had trouble fixing them like this TF101.
I've got ADB, JDK, Ubuntu, etc. since I've tried numerous times. Also, I've had no luck with the one-touch fixes. I know I'm missing something easy, I just can't figure it out.
Thank you.
Incidentally, I've tried ***http://www.transformerforums.com/fo...ry-bootloop-fix-tested-my-c10-windows.html*** , but the SDK files come in a zip, not exe and none of the files execute/install in such a way that will let me input commands. I know I'm missing something because a soft brick isn't that big of a deal.
Huh. I don't know what happened, but it involved me cleaning the screen, accidentally pushing buttons, and rebooting, and now it works. No clue, but as long as I never shut it off again, I'm set!
You're gonna need to get the PC to recognise it to fix it I'd say
Easiest way would be using Easyflasher to get TWRP recovery installed, it sounds like you have stock recovery installed at the minute
http://forum.xda-developers.com/showthread.php?t=1688012
Few people have needed new cables to get the PC to recognise the TF again, might just be needing the correct drivers though which are also linked on that page
Basically install the drivers, put the TF into APX mode,
(Vol Up & Power from powered off state while plugged into the PC)
Then run Easyflasher as admin and choose to flash TWRP (CWM is probably the reason for the bootloop, it doesn't play nice with JB ROMs)
Once you have TWRP installed, flash whichever ROM you want from new recovery and you should be good to go
I appreciate the suggestion, but that isn't doing it. I have the tab booted up and recognized by Windows, but when I try to update to a different CWM or TWRP, nothing happens. I can reboot into CWM 5.8.3.4 all day, but it won't say anything about any different recoveries I've tried to install, though the recoveries appear to be installing correctly according to the dialog given on the tablet.
I've also tried running NVflash, but nothing happens (apx drivers installed). The BAT file briefly says USB not recognized and closes.
Further, I've tried Easyflasher / one click root+recovery and I just get messages saying "ADB server out of date. Killing." The tab still reboots, but upon rebooting, it gets stuck in CWM 5.8.3.4 unless I force cold boot.
I guess the best way to describe this is to say that no matter what I do with the tab or different recoveries, I can't get rid of CWM 5.8.3.4 and no matter what I do, it default boots into CWM.
It default boots into CWM.... I think that is the key here
I remember something about that from a while ago, having to hold Power & Volume Down to boot normally, as if the OS and Recovery partitions were reversed
Unfortunately I can't remember the solution atm, but if you head over to transformerforums.com or give frederuco a PM from here or over there, Im pretty sure I remember him having a solution some time back
I shot him a message. Thanks for the suggestion.
I swear all I did was root, install Katkiss, and reboot into recovery. Is this a common problem to have THIS much trouble with such a simple process? I know now that booting into recovery can cause a loop, but this seems like way too much.
It's having CWM as your recovery when you flash a JB ROM that causes the problems
CWM & JB = Problems
TWRP is the recovery to use once you get out of this mess, good luck
Hi!
My P500 was originally Gingerbread 2.3.3, than I used CM 7.2 with AmonRa 3.0.6 recovery for a year.
So I tried to flash KitKat (http://forum.xda-developers.com/showthread.php?t=2589303), and got some issues.
I flashed ClockworkMod Recovery 6.0.4.6 (Jan/14), than the ROM (v8), and the installation worked well.
Before the reboot, CWM says:
"root access possibly lost. Fix?
this can not be undone"...
Whatever I choose, I got that black screen with
"fastboot mode started
udc_start()".
Thaaaan, I see this: http://forum.xda-developers.com/showthread.php?t=2439466
and tried to downgrade SU to v1.55. But the CWM got an error, and cannot install (even with AmonRa)...
After all, I can't get KitKat working, and got back to AmonRa recovery and CM 7.2.
To complete the "good vibe", my Android can't get AT ALL connect through USB, so I can't test any ADB command.
I don't know where I'm doing wrong... Any directions??
Thanks!!!!
SOS
This^. Exactly this is what I am suffering from right now and I am amazed how identical the issue is. I hope the OP doesn't mind if I added some more info since I didn't wanna create a new thread when one is already made recently.
Here is some info in brief regarding my issue.
Last OS: CynogenMod 7.2
Last CWM: 5.0.0.X
Target OS: Cynogen KittKat
Target CWM: 6.0.4.6 [January 2014 release]
Downloaded KittKat Rom from here: http://forum.xda-developers.com/showthread.php?t=2589303
Downloaded CWM from here: http://forum.xda-developers.com/showthread.php?t=2564767
Everything went fine when I flashed the CWM first and it entered the new recovery mode without a hitch. But the trouble began after I flashed the KittKatt Rom. Though initially everything installed just fine but in the end just before restart, this came:
"root access possibly lost. Fix?
this can not be undone"...
For safe measure I chose "Yes" and that's where my phone apparently got "soft-bricked" cause it rebooted into fastboot mode with this message
"fastboot mode started
udc_start()".
I looked around and found a "solution" for this kind of issue here: http://forum.xda-developers.com/showthread.php?t=1088046
I followed instructions to the letter but my the LG Mobile support tool refused to identify my phone. Since I figured it might have been a driver issue so I installed PDAnet instead to get stuff working. The only hitch was that PDAnet would hang on "Updating PDAnet to your phone" option. I sat their staring at it for an hour or so and figured something was wrong like my phone wouldn't allow to install anything on itself since my debugging wasn't enabled, though I am not sure about this one.
In any case I checked device manager and my ADB drivers were fine so I ran the three recovery commands in DOS anyway and they all executed without a hitch. I jumped for joy but my happiness was short lived since the phone booted back into recovery mode and now I am basically stuck up the creek without a paddle. I could really use some expert advice here just like the OP cause I really am not sure what went wrong and where. I would really like to fix this rather than flash and start the whole phone up from scratch if possible.
Regards,
LonerPrime
PS: Long time reader but this is my first post here so greetings to the xda community.
LonerPrime said:
This^. Exactly this is what I am suffering from right now and I am amazed how identical the issue is. I hope the OP doesn't mind if I added some more info since I didn't wanna create a new thread when one is already made recently.
Here is some info in brief regarding my issue.
Last OS: CynogenMod 7.2
Last CWM: 5.0.0.X
Target OS: Cynogen KittKat
Target CWM: 6.0.4.6 [January 2014 release]
Downloaded KittKat Rom from here: http://forum.xda-developers.com/showthread.php?t=2589303
Downloaded CWM from here: http://forum.xda-developers.com/showthread.php?t=2564767
Everything went fine when I flashed the CWM first and it entered the new recovery mode without a hitch. But the trouble began after I flashed the KittKatt Rom. Though initially everything installed just fine but in the end just before restart, this came:
"root access possibly lost. Fix?
this can not be undone"...
For safe measure I chose "Yes" and that's where my phone apparently got "soft-bricked" cause it rebooted into fastboot mode with this message
"fastboot mode started
udc_start()".
I looked around and found a "solution" for this kind of issue here: http://forum.xda-developers.com/showthread.php?t=1088046
I followed instructions to the letter but my the LG Mobile support tool refused to identify my phone. Since I figured it might have been a driver issue so I installed PDAnet instead to get stuff working. The only hitch was that PDAnet would hang on "Updating PDAnet to your phone" option. I sat their staring at it for an hour or so and figured something was wrong like my phone wouldn't allow to install anything on itself since my debugging wasn't enabled, though I am not sure about this one.
In any case I checked device manager and my ADB drivers were fine so I ran the three recovery commands in DOS anyway and they all executed without a hitch. I jumped for joy but my happiness was short lived since the phone booted back into recovery mode and now I am basically stuck up the creek without a paddle. I could really use some expert advice here just like the OP cause I really am not sure what went wrong and where. I would really like to fix this rather than flash and start the whole phone up from scratch if possible.
Regards,
LonerPrime
PS: Long time reader but this is my first post here so greetings to the xda community.
Click to expand...
Click to collapse
The way back home without buggy LG Mobile anything: Remove and replace batter, press home, volume-down and power keys simultaneously. Can be a bit tricky but will get you back in recovery. I assume you did that backup before playing. Restore it to get the phone back up.
Two ways to get your Kitkat:
1. Using the Version-8 install, do a clean install and be sure to choose an item in the various menu panes. Should work with this and then you need to reinstall and setup everything.
2. Take the "nightly" and install normally doing the requesite steps in the backup.
Thank you, but– Nvm fixed it.
@Dovidhalevi
Thank you for your amazing advice. I was able to get into recovery and restore from my nandroid backup. *Thank god I did that*
But kittkat ROM is still being a pain. I decided to read the logs of version 8 of the ROM a bit more closely and found this:
Upgrading from CM-10.2 or older / Fresh (First time) Installation: Now DON'T WIPE ANYTHING (Data/Factory reset, Wipe Cache partition, Dalvik Cache, Format System) everything have built in Aroma Installer. Simply flash through sdcard or adb sideload, Follow the Aroma Menu. Finish and Reboot device. Avoid Facebook, Whatsapp, Viber, Hangout apps while selecting apps to be flash, it may gives you fastboot mode. Done!!!
I decided to try my luck once more and disabled all those apps during the installation. But just before rebooting my phone lost root access again and asked if I wanted to fix it or not and then it froze again on LG logo afterwards. Another force restart and it went straight into fastboot mode. Had to do another restore to get my phone working on the older backup.
Now I know it isn't the CWD cause I am running that with my older Cynogen 7.2 OS and its rebooting without a hitch unlike kittkat which mysteriously loses root access...
I really apologize if I am being a bit noobish. Even though hardware/networking/linux[Red Hat] is like playing in my backyard, android itself is a new concept to me, hence I really appreciate all the help I can get on this to work.
MAJOR EDIT: I finally found the root of the problem and got my KitKat munching! The issue was, yep you definitely guessed it, human error... that human being me and if the original OP did everything like I did then I am guessing he made the same mistake.
What I did was, I didn't read the Aroma installer's text thoroughly enough during the installation process. At one point there comes a choice of partitions and the installer asks you to choose one of the following: *Please forgive me this is not the exact quote of the text but roughly along the same lines as memory serves*
A) Install if you are coming from a previous version of the ROM.
B) Install if you are coming from a different ROM all together.
Trust me, the way I put it makes me look like an idiot for not choosing the right choice but the actual text combined with reading carelessly on the fly ended up me botching up my initial attempts to install the new ROM. Point being you have to choose the second option and then install like usual. Following that method I wasn't faced with fastboot mode in the end and after 5 to 10 minutes of loading I was playing with the KittKat ROM. Once again I apologize for bothering you good folks and I am grateful for the guidance to the person above me.
Kind Regards,
LonerPrime
I'll try
LonerPrime said:
@Dovidhalevi
MAJOR EDIT: I finally found the root of the problem and got my KitKat munching! The issue was, yep you definitely guessed it, human error... that human being me and if the original OP did everything like I did then I am guessing he made the same mistake.
What I did was, I didn't read the Aroma installer's text thoroughly enough during the installation process. At one point there comes a choice of partitions and the installer asks you to choose one of the following: *Please forgive me this is not the exact quote of the text but roughly along the same lines as memory serves*
A) Install if you are coming from a previous version of the ROM.
B) Install if you are coming from a different ROM all together.
Trust me, the way I put it makes me look like an idiot for not choosing the right choice but the actual text combined with reading carelessly on the fly ended up me botching up my initial attempts to install the new ROM. Point being you have to choose the second option and then install like usual. Following that method I wasn't faced with fastboot mode in the end and after 5 to 10 minutes of loading I was playing with the KittKat ROM. Once again I apologize for bothering you good folks and I am grateful for the guidance to the person above me.
Kind Regards,
LonerPrime
Click to expand...
Click to collapse
Glad you fixed your phone!! I forgot to say what I did to "fix" it...
Read error... maybe???
I'll try as soon as I get home, with results!! Thanks!!!
I did that... =/
yes.. i was doing right. All the 6 times I tried...
And tried again now, just to be sure, and FASTBOOT again.
=/
jpesci said:
I flashed ClockworkMod Recovery 6.0.4.6 (Jan/14), than the ROM (v8), and the installation worked well.
Before the reboot, CWM says:
"root access possibly lost. Fix?
this can not be undone"...
Click to expand...
Click to collapse
All newer recoveries have this behavior. Because you are running a custom ROM and recovery, you should select "No" when prompted to disable recovery flashing.
Did you try the Key combos suggested by @Dovidhalevi to manually enter in to CWM?
As a worst case scenario, view this post to see how to restore your device to stock.
It's fixed, but no Kitkat...
shinobisoft said:
All newer recoveries have this behavior. Because you are running a custom ROM and recovery, you should select "No" when prompted to disable recovery flashing.
Did you try the Key combos suggested by @Dovidhalevi to manually enter in to CWM?
As a worst case scenario, view this post to see how to restore your device to stock.
Click to expand...
Click to collapse
Oh, sorry. Maybe bad explanation. I did get it fixed. All the "x" times, heheh =)
I just got in recovery by pressing home+vol up+power, and flashed back my older ROM. Now I'm trying CM 10 by Jenkins.
The problem isn't the "fastboot" message itself... but don't get Kitkat working =/
But thanks for the reply anyway!
kitkat by mukulsoni... ui stops with multiple popupd
M stuck.. i have successfully flashed kitkat by mukulsoni.. thanks. BUT UI DOES NOT START... it starts with so many popups... eg. Unfortunately voice dialer has stopped. Unfortunately bluetooth share has stopped. Unfortunately com.google.process.gapps stopped. Unfortunately com.android.systemui has stopped . Unfortunately clock has stopped. Unfortunately kitkat+ launcher stopped....
what to do. Should i get back through backup 4m recovery.. or u can help me wid kitkat .. feeling so sad..
amit2411 said:
M stuck.. i have successfully flashed kitkat by mukulsoni.. thanks. BUT UI DOES NOT START... it starts with so many popups... eg. Unfortunately voice dialer has stopped. Unfortunately bluetooth share has stopped. Unfortunately com.google.process.gapps stopped. Unfortunately com.android.systemui has stopped . Unfortunately clock has stopped. Unfortunately kitkat+ launcher stopped....
what to do. Should i get back through backup 4m recovery.. or u can help me wid kitkat .. feeling so sad..
Click to expand...
Click to collapse
Boot in to your recovery and try wiping your cache and dalvik cache.
still no working
I wish I could get these popups.
Is there something else to do??? I tried everything, everyway... Always get "fastboot mode started / udc_start()".
jpesci said:
I wish I could get these popups.
Is there something else to do??? I tried everything, everyway... Always get "fastboot mode started / udc_start()".
Click to expand...
Click to collapse
Maybe I can help... Are you flashing the same download every time? It's possible that your download managed to get corrupted. Try redownloading the ROM. I'd suggest redownloading the newest recovery also.
Now I'm going to list my ROM installation method for comparison. I personally have NEVER had an issue installing a ROM on any Optimus One variant. And I have 3 of them...
Boot device to your current recovery. CWM 6.0.45+ is compatible with CM10 - CM11 only. If you are currently running an older recovery, make a backup of your ROM with your current recovery first. Now if running an older recovery, Select "Install from zip" and install CWM 6.0.4.5+ or equivalent. Then go to "Advanced" and select "Reboot Recovery". We should now be in your new recovery. 1) Select "Wipe data/factory reset". This will wipe cache, data, .android_secure, and sd-ext.
2) Select "Advanced" then "Wipe Dalvik Cache". When done, return to recovery main menu.
3) Select "Mounts and storage". Choose "Format /system" and then confirm the action. Go back to main menu.
4) Select "Install from zip". Now we can install KitKat. Browse to and select your KitKat ROM and confirm installation.
5) If your device was old baseband ( originally running Android 2.2.2 or older ) then you will also need to flash the old baseband patch found here.
6) If you wish to flash a GApps package, that should be done now, or optionally after booting the device and letting it boot in to the ROM for the first time.
7) Go back to the main menu and select "Reboot device". If prompted to disable recovery flashing, select "NO". First boot will take 3 - 5 minutes.
shinobisoft said:
Maybe I can help... Are you flashing the same download every time? It's possible that your download managed to get corrupted. Try redownloading the ROM. I'd suggest redownloading the newest recovery also.
Now I'm going to list my ROM installation method for comparison. I personally have NEVER had an issue installing a ROM on any Optimus One variant. And I have 3 of them...
Boot device to your current recovery. CWM 6.0.45+ is compatible with CM10 - CM11 only. If you are currently running an older recovery, make a backup of your ROM with your current recovery first. Now if running an older recovery, Select "Install from zip" and install CWM 6.0.4.5+ or equivalent. Then go to "Advanced" and select "Reboot Recovery". We should now be in your new recovery. 1) Select "Wipe data/factory reset". This will wipe cache, data, .android_secure, and sd-ext.
2) Select "Advanced" then "Wipe Dalvik Cache". When done, return to recovery main menu.
3) Select "Mounts and storage". Choose "Format /system" and then confirm the action. Go back to main menu.
4) Select "Install from zip". Now we can install KitKat. Browse to and select your KitKat ROM and confirm installation.
5) If your device was old baseband ( originally running Android 2.2.2 or older ) then you will also need to flash the old baseband patch found here.
6) If you wish to flash a GApps package, that should be done now, or optionally after booting the device and letting it boot in to the ROM for the first time.
7) Go back to the main menu and select "Reboot device". If prompted to disable recovery flashing, select "NO". First boot will take 3 - 5 minutes.
Click to expand...
Click to collapse
Thanks for explanation!! But... still nothing.
I did EVERY SINGLE STEP like you said. Except for baseband, cause my phone was originally 2.3.3. But all new downloads...
After flashing, try to reboot... DAMN! "root access possibly lost..." YES/NO, gives me same problem. I read another thread about this erros, people said about SU. Can it be? I tried to flash another SU version, but CWM return an error too =/
jpesci said:
I wish I could get these popups.
Is there something else to do??? I tried everything, everyway... Always get "fastboot mode started / udc_start()".
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=2559363 try this.
voltaire23 said:
http://forum.xda-developers.com/showthread.php?t=2559363 try this.
Click to expand...
Click to collapse
Ah, thanks man! But my problem isn't the "brick" itself, but the frustration of can't get kitkat working, hehe.
By the way, I think KDZ method dangerous, by many reports that you can find all through the web. In all 217897254179 times I tried Kitkat without success, I just rebooted in recovery mode (hold HOME+VOL UP+POWER button), and recovered the last CWM backup.
But thanks to the effort =)
jpesci said:
Ah, thanks man! But my problem isn't the "brick" itself, but the frustration of can't get kitkat working, hehe.
By the way, I think KDZ method dangerous, by many reports that you can find all through the web. In all 217897254179 times I tried Kitkat without success, I just rebooted in recovery mode (hold HOME+VOL UP+POWER button), and recovered the last CWM backup.
But thanks to the effort =)
Click to expand...
Click to collapse
I am considering the jenkins build from here: http://download.androidarmv6.org/_builds/
can anyone help with finding the smallest gapps that will fit?
Edit:No need
Hi, I'm relatively new to this forum and I've been trying almost all day to root my phone...
First, I had problems trying to get a working recovery (they just crashed to random colors/or loaded fine and then rebooted like nothing happened). Tried with CWM Recovery but it seems this model is not supported atm, tried with TWRP v2.8.3.0 and also crashes... ATM the only custom recovery that has started without going haywire is TWRP v2.8.0.0 (at least for my phone).
I prefered using 'fastboot boot recovery.img' before 'flash' since it's the first time I'm trying to root a phone. The recovery mode starts okay and I also placed the UPDATE-SuperSU-v2.46.zip in the internal storage before hand. I try to install the .zip file and all goes well, no errors and a blue 'Successful' message. This is where the 'root' procedure fails. Since you can reboot or go home to check other stuff I just tried rebooting the first time and it asked me that I had a SuperSU in the device and that if I wanted to install it to have root. I obviously swiped to install it and it displayed for a split of a second the window from before and just shut down and rebooted...
I tried several other methods to try and root my phone after this failure, but none worked. I checked again if trying this procedure would serve a purpose but I got the same thing always. But since I saw the process so many times I could see for a moment a red line saying something like 'E: failed to copy su binary to /system/bin (...)' but couldn't read more because it was a split of a second there xD. I googled this weird error and I found that my /system is in read only state and not writtable... But to change it to writtable I need root too it seems <_<)
So, any help? I'm sorry if this long text makes someone just look away but I don't really know how to explain my problem in more simple words xD. Any help will be appreciated .
EDIT: Forgot to say that my phone has its bootloader unlocked already and it has USB Debugging enabled.
Moto G LTE x1040
System version (as my phone says) 21.31.1.peregrine.retla.retla.en.01 entcl
Build: KXB21.14-L1.56-1
OS: KitKat 4.4.4
Please help
Bump.
Bump.