Saw it on amazon. They said it would only work with their extended battery setup. It also appears the button areas are covered so that would make me think the case is stronger on the lip area near those buttons. I'm so curious to find out if it would fit on a Hyperion extended battery setup. Anyone try this already? I'm aware of the Hyperion tpu case and I don't like it one bit. It's too thin and the case is cut out for the buttons and weak in that area. A month or so ago, that honeycomb case was the only one out there for extended batteries.
UPDATE
It does fit the Hyperion extended life battery and door. It was a tight fit. I had to put the bottom in first then work the lip of the case over the edge of the screen all the way around. I've seen better quality tpu cases but this one does the job. It looks like you could take an exacto knife on the edges where they combined the top and bottom half. There's a little extra material there but no big deal. The volume and power buttons are not cut out so that will make the case lip area stronger in those spots. I didn't test the feel of the buttons with the case on. I just put the door on and case to see if it fits. For eight bucks, I guess there's not a whole lots to complain about. The case is gloss around the edges but matte on the flat back part. This is the most snug tpu case I've owned. It's not hard to put on, it's just snug and suggested you insert the bottom first. If you have a screen protector that is film, and not glass, and not perfectly centered, it might peel up the edges of it. I will post pictures from my other phone in a few minutes in case you're curious.
UPDATE 2:
Just tried getting the case on the phone with the battery installed too. It kinda fit but the lips of the case wouldn't completely catch over the edge of the screen. It would probably stay on but not perfectly. The Yesoo back cover, for their extended battery, must be a hair smaller than the Hyperion.
oscarthegrouch said:
Saw it on amazon. They said it would only work with their extended battery setup. It also appears the button areas are covered so that would make me think the case is stronger on the lip area near those buttons. I'm so curious to find out if it would fit on a Hyperion extended battery setup. Anyone try this already? I'm aware of the Hyperion tpu case and I don't like it one bit. It's too thin and the case is cut out for the buttons and weak in that area. A month or so ago, that honeycomb case was the only one out there for extended batteries.
Click to expand...
Click to collapse
i read the review on the gs3 yesoo extended case. and according to that...its another flimsy tpu. I would assume the s4 case is the same.
seidio released their new extended case on their site. But you have to buy their set up. Case and back door..which would set you back $55 total.
I wouldnt mind paying that..But i had a seidio extended case for the s3...and the rubber was so flimsy around the edges. And loooking at the s4 case on their site...it seems to be another flimsy set up.
That being said. The seidio is the best protection u can get at this moment for the extended battery at this moment and time. and thats not saying much.
Seidio extended batteries with my past phones, the back battery for was very thin and flimsy and never fit perfectly. There were always gaps and would never snap completely shut.
Today I said to hell with it and ordered one to see if it fits. It should be here in the beginning of next week. The shipping damned near cost as much as the case. I hope it's good and fits. I'll report back when I finally get it.
I just received my Seidio extended battery today and I got the extended Active case and holster and it's great. It's probably the slickest setup you're going to get as far as extendeds go; a little pricey but worth it.
Sent from Beanstown, USA.
Bump for pictures.
Links?
oscarthegrouch said:
Bump for pictures.
Click to expand...
Click to collapse
That looks like a decent case. Have you got a link for it?
Related
I was at my local Best Buy today looking at phone accessories when I came across this case and holster for the Nexus One. As I looked closer at it, it looked very similar to the Seidio case and holster, only it was branded Platinum. Upon further inspection, I noticed on the bottom of the packaging in small letters that it was indeed a Seidio product. What really surprised me though was that it was only $10, instead of $35 like the other cases and holsters around it, so I snatched it up right then and there.
Since all the other Platinum brand case/holster were still full price, I can only assume that they are discontinuing this in the stores. I looked on their website and it's still listed for $35. So if you've been looking to get this case and holster, I'd suggest you hit your local Best Buy and hope they still have them in stock before their gone.
I got the same one from the local best buy by me. Solid case and holster for $10. Well made and has all the needed openings for microphones, ports, ect. Phone fits face in or face out in the holster.
Appears to be a rebranded Siedo Innocase™ II Surface Combo - Black which retails for $50 on the Siedo website.
Only problem is (like other cases) you have to remove it to fit it into the desk/car dock. Still a good value.
I picked one up yesterday and tried to put it on. First off, as I was sliding the top part in slowly, it took the screen protector off with it on the upper left side. Then the rubbery material on the inside of the case peeled off as well. I had to replace the screen protector. I took it back today to exchange it. I got it on this time, but again, the upper left side of my screen protector began bubbling really badly so I took it off immediately. Now, my screen protector has these scratch lines where the case overlaps the screen and glides on when sliding on the phone. I'm glad I had a screen protector on or else the case might've scratched my actual screen. I've always had a problem with the seidio case and I was hoping this one would be different, but its not.
bskim23 said:
I picked one up yesterday and tried to put it on. First off, as I was sliding the top part in slowly, it took the screen protector off with it on the upper left side. Then the rubbery material on the inside of the case peeled off as well. I had to replace the screen protector. I took it back today to exchange it. I got it on this time, but again, the upper left side of my screen protector began bubbling really badly so I took it off immediately. Now, my screen protector has these scratch lines where the case overlaps the screen and glides on when sliding on the phone. I'm glad I had a screen protector on or else the case might've scratched my actual screen. I've always had a problem with the seidio case and I was hoping this one would be different, but its not.
Click to expand...
Click to collapse
I don't use a screen protector myself, I've had the case on and off a handful of times since I got it and it doesn't appear to be scratching the screen. I do agree though that the little rubber pieces on the inside do tend to move around a bit, but I've found that if you squeeze the case in as you slide it onto and off the phone, it minimizes the chances of the rubber moving.
Overall, I've always been very happy with Seidio's holster clips, but have to have a case on my phone cause I've very tough on phones, so I'd say the Innocase is perfect.
Now I just need to rig up a way to use the phone in the official car and home dock without having to remove the phone from the case. Gonna have to whip out the Dremel tool, soldering iron and some wood. If I get really ambitious, I may even cast some plastic molds of the phone.
Thanks for the heads up on the case. I went to my local best buy and they did not have it on display. I had to ask one of the cellphone associates to get it for me out of the back. Their SKU is: 9943421 for $9.99 regular price $34.99.
I've been using the Case-Mate tough case exclusively since I purchased the phone in March. All I can say is I'm amazed at how thin this case is. It feels as if there really is no cover on the phone. The addition of a secure belt clip is a HUGE plus in my book. My only gripe so far is I don't think this case will do much good in protecting the phone from a drop out of your pocket or coat.
Funny you should say that, I too just switched from the Tough Case as well. I did love the CM case for the combination of shock absorbing rubber and hard plastic shell, but it made the phone too bulky. As for the Seidio, it may be thin and not offer as much protection as the CM case, but take into account that the shell of the phone itself is metal and hard plastic and comes into direct contact with the screen. Any drop is going to transfer from the shell and into the screen most likely causing it to break. A case on the phone, even a thin one, is still more flexible than the phones shell and absorb most impacts. Even if the case itself breaks in a fall, better a $10/$35 case then a $579 phone.
garfnodie said:
Funny you should say that, I too just switched from the Tough Case as well. I did love the CM case for the combination of shock absorbing rubber and hard plastic shell, but it made the phone too bulky. As for the Seidio, it may be thin and not offer as much protection as the CM case, but take into account that the shell of the phone itself is metal and hard plastic and comes into direct contact with the screen. Any drop is going to transfer from the shell and into the screen most likely causing it to break. A case on the phone, even a thin one, is still more flexible than the phones shell and absorb most impacts. Even if the case itself breaks in a fall, better a $10/$35 case then a $579 phone.
Click to expand...
Click to collapse
After a few hours of using it, I switched back to my tough case. I just can't get over how "under protected" the phone feels. I did however use the Seido case when I had to wear a suit earlier this week. I like having my phone on my belt in those cases. For 10$ its a nice option to have.
Now if there was only a way to get the Seido holder to hold the n1 with the tough case on it.....
No joy at my local best buy - but I found an open-package one on Ebay for $7.99 with free shipping - same item.
Open package is no big deal to me though...
Thanks for opening my eyes to this product!
just got this as my seido case was getting really messed up.
the only difference i see is that the inside is rubber rather than seido's felt interior
krazichinaman said:
After a few hours of using it, I switched back to my tough case. I just can't get over how "under protected" the phone feels. I did however use the Seido case when I had to wear a suit earlier this week. I like having my phone on my belt in those cases. For 10$ its a nice option to have.
Now if there was only a way to get the Seido holder to hold the n1 with the tough case on it.....
Click to expand...
Click to collapse
Sound's to me like what you need is the Seidio rugged case. It's similar to the Tough case in that you get a thick rubber wrap with a plastic shell around it, and then that fit's into a special spring holster.
http://www.seidioonline.com/product-p/bd4-hkr4hnx1.htm
I'm sticking with the regular case/holster as that will more than protect the phone from even a tall drop.
what is the best epic 4g case? post yours...
I bought the Black Samsung one from the Sprint store for $19.99. It works great and does what I want.
Yeah, I know. I'm boring
TheCraigJ said:
I bought the Black Samsung one from the Sprint store for $19.99. It works great and does what I want.
Yeah, I know. I'm boring
Click to expand...
Click to collapse
haha the sprint cases are fin & your not boring..
I'm using the Seidio Innocase Surface case/holster combo. Nice tactile feel on the case, and the secure spring-clip holster does really well, especially with my clumsy arse...
Sent from my SPH-D700 using XDA App
Definition of the "best" case would be different for every person because it depends on personal preferences, how you use your phone, and how you carry it. Personally, I like the feeling of a naked phone and with my Touch Pro 2 I mostly used Forte leather case (although I tried Seidio Surface for a short period). The advantage of a leather pouch is that you don't have any permanent thickness added to your phone, but disadvantages are that you need to take the phone out of the case to see the screen and you can still drop the phone while out of the case - which is exactly what happened to me a few times. Now when I got Epic, it is thinner then TP2 so I wanted to get a snap-on case for it. Here is my mini-review of a few cases I tried:
1) Seidio Active - it is the case that (among other snap on cases) would definitely provide the best protection if the phone is dropped, it looks good, and made well. The soft gel provides a nice cushion and the plastic skeleton strategically positions hard coverage over areas that could be most impacted during the fall. It seems that the recently found Fishbone case on Amazon is very similar in the design so I would expect it to provide the same protection. Unfortunately, Seidio Active was a bit too thick to my liking and since I usualy take good care of my phones, I didn't feel that the extra protection would justify the added thickness for my needs.
2) Seidio Surface - this is probably the thinnest snap on case you can get. I really like the fact that it adds very little to the overall size of the phone and I thought that it would be the perfect case for me when I bought it and put it on. However, maybe the fact that it is so thin contributed to the fact that it feels a bit flimsy when on the phone. There is a tiny bit of play on both the top and bottom parts (when you squeeze them with your fingers on the sides) and sometimes when you push power button the phone tends to slide open a bit based on how I hold it in my hand. The case seems to fit like a glove but it is not as tight as I would like it to be and it is VERY easy to remove the top part with almost no effort whatsoever. Some may consider it a plus, but I consider it a minus because I am pretty sure that if the phone is dropped, the top part will most likely fall off after the first bump leaving the top unprotected (this actually did happen when I used Seidio Surface case on my Touch Pro 2 and dropped from about 3 feet onto hardwood floor).
3) Sprint Case with rubber back - to me this turned out to be the "best" case, at least for now. In terms of added thickness it is somewhere in between Seidio Active and Surface cases. It fits very snug and tight. I like the rubber backing a lot, it is not slippery, feels very nice in hand, and looks good (at least in black). Some people mentioned that the rubber has a tendency to peel off - I've had this case for a month now and it looks like new and I have no peeling issues; but even if I do, I am sure that a carefully placed drop of crazy glue will take care of this issue permanently. I have removed the case several times and I don't see any scratches left on the phone as was posted in one thread. The only drawback may be that the case is a bit harder to remove then Seidio, but to me it is not an issue and means that it will stay on during the fall. I rarely remove the top part, but I am a heavy phone user so I swap extra battery often and don't have any issues removing the bottom part after getting used to it. There were some reports of snaps breaking off - I have not experience that at all and I hope I won't since this is a perfect case for me at this point.
In terms of price - all three cases are around $20 bucks so price is not a factor. All three cases do not interfere with the sliding mechanism and make the phone feel a bit tighter with less screen play and no more squeaking from the battery door. I also tried one of those invisible shield things which is basically a screen protector over the entire phone. Two issues I found with those: a) no matter what brand you get, they will eventually start peeling and will attract dirt on the edges looking like crap after a while; b) although they provide scratch protection, they won't do much if the phone is dropped.
Hope you'll find your best case.
Cheers.
My sprint case has all the tab breaking off after about a month and a half of use. YMMV.
Geekybiker said:
My sprint case has all the tab breaking off after about a month and a half of use. YMMV.
Click to expand...
Click to collapse
I wonder if this has to do with how different people remove/put it on. I usualy pick the two corner clips on the charger side with my nail and it removes pretty easily after that (just slide it off). When I put it back I do it in reverse order - I slide the bottom two clips on first and then snap the top ones on. So far it's been working well for me.
I'm using a black Seidio Innocase (regular not active) with the spring clip holster and I love it. I originally had the body glove case and it was just too big.. felt like I was carrying a brick in my pocket. The Innocase doesn't add much bulk and gives a bit of protection from random bumps and scratches. Has a pleasant lip around the screen too so laying the epic flat on its face keeps the screen from contacting a surface.
Sent from my SPH-D700 using XDA App
My experience with case durability is completely different from gorby911's, so it's all YMMV. My Sprint case completely fell apart in 1.5 months of use, what with the clips breaking off, and 2 corners of the rubber backing peeling away. Even after Gorilla-gluing one of the corners, it peeled off again within a week! Just got a Seidio Surface and it fits very snugly and no play.
The downside of the Surface is that its rubberized texture is actually quite slippery, vs. the grippy texture on the Sprint case (especially with its rubber backing). It slightly twists and slips around in my hand that supports it while I'm swiping around with my other hand. But it's got a much thinner profile with what I feel appears to be the same amount of protection.
I hope it lasts more than 1.5 months long.
So the sedio active is the slimmest case? May have to check that out, thanks for the info.
ranchosteve said:
So the sedio active is the slimmest case? May have to check that out, thanks for the info.
Click to expand...
Click to collapse
Seidio innocase should be the thinnest.
I've been using the BodyGlove that has a the smoked chrome. Stylish and strong. Dropped it a few times and everything's still fine. Sprint Direct/Indirect stores have them available.
gorby911 said:
I wonder if this has to do with how different people remove/put it on. I usualy pick the two corner clips on the charger side with my nail and it removes pretty easily after that (just slide it off). When I put it back I do it in reverse order - I slide the bottom two clips on first and then snap the top ones on. So far it's been working well for me.
Click to expand...
Click to collapse
I have both the Innocase Surface and the black Sprint case and I too have had no problems with my Sprint case - I take off the back of the case exactly as you have described. Not a single scratch on my phone yet (knock on wood). I prefer the Sprint case over the Innocase as it seems to offer better protection.
For those who are curious, the black Sprint case fits in the Seidio Innocase Holster (the one designed for the Innocase Surface at least). I bought the $40 Innocase/holster combo at Best Buy, but am using the holster with my Sprint case.
I'm using this one. Got it off fleabay for $8.99. Really nice OEM leather case that fits great. I can't stand a phone in my pocket so I have mine on my belt.
I really don't like the extended battery door that came with my ebay 3000 mah battery, so I lightly modded the original door to make it fit the extended battery. Keep in mind this is my first attempt... it has a lot of room for improvement.
do you know if you can use the ebay case with a belt clip holster? I am not a fan of the seidio case either, the ebay case looks better.
Looks good, whats tools did you use?
I was thinking about doing this but don't have the proper tool too. Have you considered making a plastic mold to cover the battery? I have heard of people using some thing call shurgoo to make custom plastic pieces.
I have seen pictures somewhere on here of people that are using the seidio clip holster with the back half of the case removed with the ebay battery door, but I now cant find the pictures... i know that mine would fit in a normal belt clip holster because the bottom and top are still as if it was in the stock case.
As far as tools, i just used a pocket knife, a pair of scissors and liquid super glue. Maybe shoe-goo? i dont have any idea what shurgoo is? I do want to try to make something out of plastic or fiberglass resin maybe.
I don't mind having the extra thickness, but all 3 of the extended battery covers I've gotten via eBay always have bad fitment just around the power button. It sticks out past the button and/or that same corner never stays down. I'm tempted to do something like take the stock cover, cut an opening in it, and then epoxy the hump from extended cover onto the stock cover. After that, I plan on finishing it off w/ wrapping it in some 3M DiNOC black CF since I've got some extra sitting around. Anyone wanna donate a stock battery cover?
Hey guys,
Just bought the Incipio Feather case and wanted to share my thoughts in case some people were thinking about buying.
The case is definitely very light weight and pretty thin (Incipio states that it is less than 1 mm thin). It's an "ultra light, ultra strong polymer" hard case that is smooth to the touch while having a slightly rubbery feel to it. The case itself has very clean edges with no trace of any manufacturing defects. There are cutouts for the power and volume buttons, hdmi port (it's covered in the pictures on their site, but there is indeed a cutout for this), usb port, camera, microphone, headphone jack, and speakerphone. With the exception of the battery, everything is easily accessible through these cutouts.
As for protection, this is where I've been disappointed. First off, the side of the case does not rise above the side of the phone, so when you put the phone face down, the screen will be touching the surface (they provide a screen protector, but I don't think that's enough). Secondly, the case does not completely wrap around the phone, so both the top and, more importantly, the bottom of the phone are exposed. The bottom is important because on a straight drop, the pointed part of the phone will take all of the impact because it protrudes beyond the corner parts of the case. The top isn't as bad because it's flatter, so the corner portions of the case will ideally take the impact. Granted, you aren't purchasing a "feather" or "barely there" case for its protective qualities, but I think that had Incipio manufactured the case to fully wrap around the phone, both the protection and aesthetics of the case would have been enhanced.
In regards to the aesthetics, I purchased the case to avoid the bulkiness of other cases so that I could enjoy the look of the phone. However, the cutouts and the fact that the case doesn't fully wrap around the phone cause the Feather case to "break" the smooth lines of the phone. I would definitely prefer the look of a case that fully wraps around the phone.
Overall, I would not purchase this case again. At $25, even with the screen protector and microfiber cloth, I think that a case like the Androidified case that I previously reviewed provides better value with more protection. With the TPU case, my phone experienced no damage after I accidentally dropped the phone while getting out of a car. I can't say that the Feather case would provide the same sort of protection.
Thanks for the review, this was my favorite case when I had my Atrix. I noticed it on the site the day it went up but did not buy it because an employee confirmed over live chat that there was no hdmi cutout. Now that I know it is there I am placing an order now. I just bought the otterbox and I like it but its just too much for me.
This is almost the same exact case as this:
http://www.verizonwireless.com/b2c/store/accessory?action=accessoryDetails&accessoryId=47557
But yours is probably a tiny bit thinner. And this one has a pull out stand which is awesome. They tried to sell this hardcore when i bought the phone, and I got it then.
Syn Ack said:
This is almost the same exact case as this:
http://www.verizonwireless.com/b2c/store/accessory?action=accessoryDetails&accessoryId=47557
But yours is probably a tiny bit thinner. And this one has a pull out stand which is awesome. They tried to sell this hardcore when i bought the phone, and I got it then.
Click to expand...
Click to collapse
The Incipio also doesn't have those rubber ridges. I had one of these cases on my Thunderbolt and I hated it because I keep my phone in my pocket. Went with a Case-Mate Barely There case which seems to be similar to the Incipio.
It reminds me of an ultra light 1 piece Seidio innocase. It has a similar feel but its lighter and thinner.
After using this case for a few days I have to agree. This case is not worth it at all. The feather used to be my choice but incipio did not do well with this one.
I'm really hoping case-mate jumps on it and makes a barely there case for the Charge.
http://feedback.case-mate.com/forum...867323-samsung-droid-charge-barely-there-case
immaage said:
I'm really hoping case-mate jumps on it and makes a barely there case for the Charge.
http://feedback.case-mate.com/forum...867323-samsung-droid-charge-barely-there-case
Click to expand...
Click to collapse
Yeah same here. I went back to my Otterbox case but I just ordered the Trident Aegis today. I would rather have a thin light case but this feather is just plain terrible.
Why you going with Trident Aegis..instead of just using the Otterbox?
Just curious on your thoughts on the Otterbox..did you get the Trident? How is it?
The Otterbox is a good case but I am not too sold on having the buttons on the bottom covered. The Trident case shipped today and I will post pics and a review of the Aegis when it comes.
Otterbox cases are some of the best protection that you can get for your smartphone. There are three available for the Galaxy S6 and coming soon for the Galaxy S6 Edge ( Sign up Here to Be Notified ) You can get more customization though the OtterBox site. There is also Free Shipping on all cases within the US.
OtterBox COMMUTER SERIES:
OtterBox DEFENDER SERIES:
OtterBox SYMMETRY SERIES:
To get a idea of what these cases look like on the GS6, then view the reviews here:
(OtterBox Commuter Series:
(OtterBox Defender Series:
Bump
I'll chime in with this:
felloffthetruck said:
I'll chime in with this:
Click to expand...
Click to collapse
You have the same exact color option that I have.
Been rocking the Otterbox Commuter case since I first got my phone. It's a nice case. Since I carry my phone in my pocket, dust covers were a must. You should see the ports on my old Nexus 4, lol. I didn't want the defender as it is too bulky, so the Commuter was perfect. The dust covers are great and the case leave you enough room for a screen protector. I did just get the standard tempored glass protector from Verizon, but if all protectors are created equal, then you won't have a problem. The bottom of the case does just barely touch the protector. If you have a protector any bigger, the lip of the case will cover or push up against it. I do have one or two gripes with it, though...
It wants to slip out of your hand and is a tiny bit of a pain if you want to take the case off and put it back on. I think if the lines on the edge of the hard part of the case were horizontal instead of vertical, the case would have a better grip and not want to slide out of your hand. With the grooves being vertical, they case just glides right out of your hand.
I often have to take my phone out of the case because I run, so I have an armband that I put my phone in (having to switch cases like this is also why I got the Commuter and not the Defender...easier to take the case off and i'm sure the Defender case will eventually break from constantly having to take it apart). If you take your phone out of the case and you need to put it back, there's a certain way you have to do it. Put on the soft cover first. After that, you need to put on the hard cover on starting at the bottom. Sit the phone down into the bottom part and then pull the dust covers through the cut outs and then drop the phone the rest of the way into the hard cover. From there, the rest of the hard cover part pops right over the rest of it very easily. It's a little tricky at first, but over time, i'm sure you'll get the hang of it.
Overall, I like this case.
Not happy with Defender failure
blackout720 said:
Bump
Click to expand...
Click to collapse
I suggest no one buy the Defender for the S6 until they show they have fixed the plastic housing, the holster, or both.
The housing on mine has a broken latch after only 2 weeks of use. The Defender for my old S4 last 2 years and still works fine.
The new housing has a smaller perimeter around the latching slot for the holster. Also, the holster tab is now two little nibs, as compared to a solid tab on the S4 design.
The smaller interface area combined with the thinner material on the housing caused mine to break easily. Now the phone wont stay in the holster unless I turn it around to use the unbroken side. I know that side will be breaking soon as well.
To top it off.....Otterbox's website wants me to give them a credit card so they can charge me $ 6.99 for handling the issue.
I am pretty disappointed in the new Otterbox. Am looking for an alternative since the design is poor and the return policy on such a premium product is less than "premium" in my eyes.