Database Info

Case Review: Incipio Feather Case

Hey guys,
Just bought the Incipio Feather case and wanted to share my thoughts in case some people were thinking about buying.
The case is definitely very light weight and pretty thin (Incipio states that it is less than 1 mm thin). It's an "ultra light, ultra strong polymer" hard case that is smooth to the touch while having a slightly rubbery feel to it. The case itself has very clean edges with no trace of any manufacturing defects. There are cutouts for the power and volume buttons, hdmi port (it's covered in the pictures on their site, but there is indeed a cutout for this), usb port, camera, microphone, headphone jack, and speakerphone. With the exception of the battery, everything is easily accessible through these cutouts.
As for protection, this is where I've been disappointed. First off, the side of the case does not rise above the side of the phone, so when you put the phone face down, the screen will be touching the surface (they provide a screen protector, but I don't think that's enough). Secondly, the case does not completely wrap around the phone, so both the top and, more importantly, the bottom of the phone are exposed. The bottom is important because on a straight drop, the pointed part of the phone will take all of the impact because it protrudes beyond the corner parts of the case. The top isn't as bad because it's flatter, so the corner portions of the case will ideally take the impact. Granted, you aren't purchasing a "feather" or "barely there" case for its protective qualities, but I think that had Incipio manufactured the case to fully wrap around the phone, both the protection and aesthetics of the case would have been enhanced.
In regards to the aesthetics, I purchased the case to avoid the bulkiness of other cases so that I could enjoy the look of the phone. However, the cutouts and the fact that the case doesn't fully wrap around the phone cause the Feather case to "break" the smooth lines of the phone. I would definitely prefer the look of a case that fully wraps around the phone.
Overall, I would not purchase this case again. At $25, even with the screen protector and microfiber cloth, I think that a case like the Androidified case that I previously reviewed provides better value with more protection. With the TPU case, my phone experienced no damage after I accidentally dropped the phone while getting out of a car. I can't say that the Feather case would provide the same sort of protection.

Thanks for the review, this was my favorite case when I had my Atrix. I noticed it on the site the day it went up but did not buy it because an employee confirmed over live chat that there was no hdmi cutout. Now that I know it is there I am placing an order now. I just bought the otterbox and I like it but its just too much for me.

This is almost the same exact case as this:
http://www.verizonwireless.com/b2c/store/accessory?action=accessoryDetails&accessoryId=47557
But yours is probably a tiny bit thinner. And this one has a pull out stand which is awesome. They tried to sell this hardcore when i bought the phone, and I got it then.

Syn Ack said:
This is almost the same exact case as this:
http://www.verizonwireless.com/b2c/store/accessory?action=accessoryDetails&accessoryId=47557
But yours is probably a tiny bit thinner. And this one has a pull out stand which is awesome. They tried to sell this hardcore when i bought the phone, and I got it then.
Click to expand...
Click to collapse
The Incipio also doesn't have those rubber ridges. I had one of these cases on my Thunderbolt and I hated it because I keep my phone in my pocket. Went with a Case-Mate Barely There case which seems to be similar to the Incipio.

It reminds me of an ultra light 1 piece Seidio innocase. It has a similar feel but its lighter and thinner.

After using this case for a few days I have to agree. This case is not worth it at all. The feather used to be my choice but incipio did not do well with this one.

I'm really hoping case-mate jumps on it and makes a barely there case for the Charge.
http://feedback.case-mate.com/forum...867323-samsung-droid-charge-barely-there-case

immaage said:
I'm really hoping case-mate jumps on it and makes a barely there case for the Charge.
http://feedback.case-mate.com/forum...867323-samsung-droid-charge-barely-there-case
Click to expand...
Click to collapse
Yeah same here. I went back to my Otterbox case but I just ordered the Trident Aegis today. I would rather have a thin light case but this feather is just plain terrible.

Why you going with Trident Aegis..instead of just using the Otterbox?
Just curious on your thoughts on the Otterbox..did you get the Trident? How is it?

The Otterbox is a good case but I am not too sold on having the buttons on the bottom covered. The Trident case shipped today and I will post pics and a review of the Aegis when it comes.

Verizon Case Gameplan

So my plan was to get the slimmest case I could for Verizon note 4. On my note 3 I had the incipio feather case (loved it-although little protection).
Got my note 4 and no readily available cases. Went naked for a week. Ordered the spigen thin fit (incipio feather not available?).
Got it (no mic hole issues as it is open on bottom). It is a bit slippery but is exactly like feather case. Very very annoying how ever-increasing does squeak when put pressure on sides - clearly mold only 95% accurate...
Now this is the slimmest case out there.... And I am so missing carrying this phone naked. The Samsung back feels so grippy and nice. Amazing how even this thin case adds noticeable bulk.
Starting to get contaminated with "this thin fit case doesn't protect much anyway.....
This phone naked is the bomb. Anyone routinely not case phone and have success.? I saw someone yesterday with note 3 looked like a banged up car on sides. Slapped the spigen back on. Hahaha
As an aside, waiting for the official Samsung protective cover - may be a good solution. But, sold out on Samsung site..... Anyone have this one? No video reviews that I can find.

For the squeaking, just put strips of masking or electrical tape on both sides of the inside of the case. Silly that you have to do anything, but this is a solution.

Video review of 4 cases

(with a kinda drop test)
s line case, Nillkin Amazing Armor Bumper,Samsung protective cover+
http://youtu.be/94QtQB9x2CE?list=UUACeOFuBKLUX5JzaYFqAwWQ

Thanks for the reviews...in regard to the Nillkin case/bumper...I only found sellers in China on eBay...you know of any US sellers or Amazon sellers? I checked both but didn't find anything...thanks!!

Yes your correct I purchased it from a China supplier via eBay. It took a couple of weeks to arrive but overall good value for money.

I have two of the 3 main cases reviewed in same colors. The Samsung protective case fits better than the Nillkin. The Nillkin required some excess removal around the USB and mics to fit without slightly pulling away from bezel near the home button and allowing light to peak through the USB port. The fit here is much better on the Samsung case.
The lack of side grip is actually worse and more like the Verus Thor case, the Samsung protective case gets more slippery when cold than the Nillkin case. The Nillkin despite its smooth sides doesn't lose as much grip when cold.
Also, the Nillkin case fits the headphone jack better IMO because it covers all the chamfered edges. Once I fitted the USB port, I could say that I prefer its fit around the USB port better for the same reason but there is some concern about the fit near the mics. The Samsung case fits the mics perfectly and tight and even accommodates the Verizon spacing here. My modification on the Nillkin is not precise so I think the Samsung case may actually sound better on a call.
The review mentions the Nillkin is easy on, easy off; exactly, but it appears the Samsung case is harder to remove than even the Verus Thor despite looking and feeling quite similar around the bezel lip. The Samsung case feels as if it needs to stretch to come off but less cooperative at doing so when cold.
Others have said the Nillkin is compatible with the OEM wireless charger cover. If so, the case may appeal to both the wireless chargers and frequent battery replacement users.
I may try the S curve case but would like to know if it covers the chamfered edges as nice as the Nillkin but also fits the mics as perfectly as the Samsung protective case+?

damn that sucks about the Samsung case.. amazon is full of 5 star reviews so I got it.. and now I'm reading it sucks. and i spent 20 bucks on that stupid thing. damnit. oh well it comes Monday so we'll see. I'm using the diztronic now and it's nice, but i agree with him that the s line case is great. I've got the same one, but it doesn't fit as well as it should around the bottom lip of rhe phone, and the cutouts don't match the Verizon one. also, there's no raised edge around the camera and i don't like that since I place my phone down on its back.
Sent from my Samsung Galaxy Note 4 using Tapatalk.

There must not be a perfect case out there at the moment. What disappoints me about the Samsung protective case+ is the cold grip and ease of removal. Your results may differ; hoping warmer weather improves the ease of removal. I do think the warmer weather grip is good. We've had a warm day and a cold day since the case arrived. The fit is as nice as the Verus Thor.
To be fair on the grip gripes, I have small hands and suffer from dry skin in colder environments. Both tend to make these cases cold, hard and slippery.
Thanks for the commentary on the S Line case.
The cases compromise one thing or another. For now, I can deal with the lack of grip of the Samsung case because it's minimal. Don't get bummed until you try it yourself.

I got the Samsung, and i have no problem with grip issues. probably bc i used the diztronic for like 3 weeks.. and the sides of that are slippery too. this to me is decent enough grip. I actually love this Samsung case. it's thin. feels better than the diztronic. really keeps the phone shape the same. I got the blue and it looks so cool
Sent from my Samsung Galaxy Note 4 using Tapatalk.

I thought I was going to buy the Tech 21 Tactical Impact in matte black today. T-mobile only had the mesh in purple; I tried the fit on my phone and hate the exposed chamfered edges near the headphone jack. Also lacks the raised camera lip. Disappointing. The salesman said the black matte case, which they didn't have ATM, would be identical in fit. Deal breaker for my pursuit of a better case. The Nillkin Armor bumper case and Samsung are the better cases, for me. The Verus Thor is third for me.

Next week I should recieve e.grips which I plan to stick on the Samsung case.
It's amazing that we can't find a great slim case with a good grip.

[Q] Good protection (Cases, bumpers) recommended by other user experiences?

I have my s4 since november and already dropped it three times. Once on a wooden floor and two times on concrete. The phone survived (even the screen) but it got some bruises. The top left and bottom right "corner" of the phone are a bit malformed from the two falls on the concrete. Every time it fell out of my pocket, so it's not a matter of hand grip.
So I decided it's time for some protection.
I have a silicone case. It's one of those book thingies. But it was cheap, it's thin and I'm not really fond of it. Mostly because I have a hard time reaching the buttons.
Yesterday I got a hard plastic case. But the problem with this one is that it only offers protection at the back and the sides of the phone (left and right), the top and bottom are unprotected. And there is the button problem too.
My concern is that when the phone falls down, the most impact is taken up by the margins (I don't remember the technical term). It rarely happens that the phone falls flat on the screen (generally speaking). It mostly falls and hits with the margin first. And that's mostly where the screen starts to break too.
And I don't really want to go overkill with one of those bomb resistant cases :laugh: I don't want the phone to become more bulky (what's the point of a sleek design if it's ruined by a huge case)
I don't use GPS. I heard some metal cases mess with signal reception.
Considering the above, I thought I should go for a metallic bumper, or maybe silicone bumper.
I'm asking for some other user experiences here. What others have found to offer good protection and stuff. And I'm not asking for a product. I'm just asking what type of product (Case or bumper, and whatever other options there are)

I was using S-line silicone cover for my i9070 (SGS Adv) and it was nice all rounder.
Dropped phone form desk on concrete, fell off my pocket on the street ... it was all fine.
It wasn't really much thicker than phone on its own and buttons were easily accessed. I have not tried this type on S4 but I imagine there is one.
Currently in i9505 I have more bulkier case - case mate hybrid tough (2 layers: rubber "inside" similar to every silicone case there is, and plastic outside - looks like what you described as your sides/back only case, with some plastic on the corners) - buttons / screen are a bit "deeper" in the case (thicker ruber overlay on sides than it was on S-line in i9070) but damn it feels like it can survive throw at the wall and bouncing off the ground.
Sent from my TF300T using XDA Free mobile app

Amer shellster
I've been using an Amzer Shellster for my S4 and really happy with it. Cost me £12.89 including delivery. Bumper case adds minimal bulk yet provides goof protection against falls. Really like the hip holster for use running or biking.

Can Anyone recommend me a slim fit cover that fits nicely on the s4, not too expensive but not too cheap. Thanks
Sent from my GT-I9505 using Tapatalk

CaseMate Tough case. Cost me about $20 at Walmart, though it's probably a lot less on Amazon. It fits perfectly, even with a glass screen protector installed on the touchscreen. It also has a textured back which provides the "grippy" feeling that the S4 polycarbonate lacks.

I'm currently using an original Protective cover+, and though it wasn't that cheap I definitely can recommend it. Fits perfectly (of course), no problems with connecting my S4 with a docking station. Since I've got the cover I've "thrown" away my S4 four times. The first "test" was when it fell on the street while pulling it out of my backpack. Second time I used it as a torch and it fell 2 meters down on wooden ground. The other two times it fell on carpet. Nothing happened at all to my good old phone, not even a scratch on the back. Also no problems at all with using the hardware keys or headphone jack.

Otterbox commuter would get the job done. But it makes ur s4 a little bulky. Have to sacrifice that for good protection though.

I have the Spigen Neo case. It's not bulky at all but provides good protection. The case itself have buttons over the phone's buttons. I have a glass screen protector also and the 2 together is nice.
http://www.amazon.com/gp/product/B00BYJXGP2/ref=oh_aui_detailpage_o06_s00?ie=UTF8&psc=1

I went for a basic cheap case from dx.com, SKU: 200649. But it does cover all sides, the back, as well as some of the front, due to the overhang from the sides extending out the front. I got a few other cases with different materials at the same time, but this is the one I ended up liking the most.

Thank you all for the replies.
I decided to get a metallic bumper. It does seem to mess with signal strength a bit, though.
But I guess it offers much more protection than rubber/silicone or plastic. It also held together tightly with a pin (You don't just slip the phone in. The bumper can pe opened at one corner, you put the phone in, then close the bumper using the pin). So it won't fly off on impact.
I think this combined with a glass screen protector will ensure optimal protection.

I am using a body glove 3 piece. It has a screen protector and a silicon/rubber outer cover. It was $25 dollars. It hasn't effected my signal and has survived a few falls. I know they sell them at Wal-Mart and Target.

Review: MoKo [Heavy Duty] case for Nexus 6P Huawei

Hi guys,
I finally got around to doing a review on the Moko Heavy Duty Case for my 6P. I ordered this on amazon.ca. I've rocked this case for about a week now since I did that video, and I am pleasantly surprised.
The cutouts are precise, and the case does not look or feel cheap. The fingerprint scanner is easy to use still as well. The plastic is pretty soft, and I don't think it would stay on on its own without the black shell, but it does fit perfectly. Also, didn't notice much pocket lint or anything else sticking to it like some have reported. Overall it's a great option for a more rugged case for the Nexus 6P, especially here in Canada, where the options can be sparse. Here's the link from amazon.
Nexus 6P Case - MoKo [Heavy Duty] Full Body Rugged Holster Cover with Swivel Belt Clip - Dual Layer Shock Resistant for Huawei Google Nexus 6P 5.7 Inch Smartphone 2015, PURPLE https://www.amazon.ca/dp/B00JP6J1A0/ref=cm_sw_r_other_awd_HnYMwbXKYG11S
11 bucks plus tax, and since I have PRIME, also got free 2 day shipping. Yes, I have a compulsive online shopping problem...
I will also post reviews for my Spigen Rugged Armour and a Poetic Revolution cases shortly.
https://youtu.be/k2k6gPdRPUY
Sent from my Nexus 6P using Tapatalk

I've got one in blue but I don't use it anymore. It's a pretty nice case and the quality is fantastic I just wish they would stop putting those huge bumps on the back for no reason. They serve absolutely no purpose and double the thickness of the phone. They do this on these cases for all phones and just still makes no sense.

RED ZMAN said:
[...] I just wish they would stop putting those huge bumps on the back for no reason. [...]
Click to expand...
Click to collapse
You might be interested in this CoverON case, which has no such huge bumps on the back. It has an unusual 3-piece design, with a hard plastic piece that snaps on from the front of the phone (in addition to the usual one from the back), locking the soft TPU in place in the middle. I'm quite happy with the build quality, and because of the design it seems like possibly the toughest case you can get that (a) still looks even remotely normal and (b) doesn't have an integrated plastic screen protector, making it easy to add a tempered-glass one of your own. (Note, though—I have an IntelliArmor "case-friendly" TGSP, and it fits perfectly but with absolutely no room to spare. Full-coverage TGSPs will definitely interfere with the TPU at the edges of the screen, although because of the way the case fits together you might be able to get them to nestle nicely under it without lifting up.)

daniels220 said:
You might be interested in this CoverON case, which has no such huge bumps on the back. It has an unusual 3-piece design, with a hard plastic piece that snaps on from the front of the phone (in addition to the usual one from the back), locking the soft TPU in place in the middle. I'm quite happy with the build quality, and because of the design it seems like possibly the toughest case you can get that (a) still looks even remotely normal and (b) doesn't have an integrated plastic screen protector, making it easy to add a tempered-glass one of your own. (Note, though—I have an IntelliArmor "case-friendly" TGSP, and it fits perfectly but with absolutely no room to spare. Full-coverage TGSPs will definitely interfere with the TPU at the edges of the screen, although because of the way the case fits together you might be able to get them to nestle nicely under it without lifting up.)
Click to expand...
Click to collapse
Nice to see somebody on this site review that case. Which color did you get? Do you have any holsters to see if this will fit?

RED ZMAN said:
Nice to see somebody on this site review that case. Which color did you get? Do you have any holsters to see if this will fit?
Click to expand...
Click to collapse
I have the black version. Based on the pictures on Amazon the colors looked like they'd be pretty in-your-face, especially since the highlight color is visible directly around the edges of the screen. I'm afraid I don't have any holsters—I've never used one.
I realize, I forgot to mention the most important thing! The headphone and USB-C cutouts on this case, as shipped, are not large enough for most cables. The stock USB-C cable fits but scuffs the sides, many high-quality third-party cables won't, and the only headphone plugs that will fit are the super-tiny ones that some headphones have for exactly this reason. But! If you have a decent utility knife, some courage, and a steady hand, it's possible to enlarge the cutouts without messing up the case. (I cut away a tiny bit of the TPU near the jacks as well, since it was being deformed when plugging in a cable.) With this done it works beautifully—the case is even thin enough to use a Square credit-card reader in the headphone jack.