Related
I have had a idea about this for weeks and the soultion
http://www.maplin.co.uk/conductive-pen-33837?tabid=1&criteria=usb&c=so&u=strat15
As This pen is used to re-place broken conductive tracks on circuit boards etc
(for those want to know exactly what its for, read on the site)
my idea is to coat the back of the plastic where the wifi and gsm aerial's make contact with the board to amplify the signal, instead of the little tracks that htc have provided.
But my problem is finding a video showing the camera area removed without damaging it (where the wifi arial is)
I have been in the gsm repair trade for years, and i take this idea from the old nokia 3210's and the aerial's on those which used to just clip of and where the same idea.
bleach1 said:
I have had a idea about this for weeks and the soultion
http://www.maplin.co.uk/conductive-pen-33837?tabid=1&criteria=usb&c=so&u=strat15
As This pen is used to re-place broken conductive tracks on circuit boards etc
(for those want to know exactly what its for, read on the site)
my idea is to coat the back of the plastic where the wifi and gsm aerial's make contact with the board to amplify the signal, instead of the little tracks that htc have provided.
But my problem is finding a video showing the camera area removed without damaging it (where the wifi arial is)
I have been in the gsm repair trade for years, and i take this idea from the old nokia 3210's and the aerial's on those which used to just clip of and where the same idea.
Click to expand...
Click to collapse
i remember someone saying that the heated their phone to remove the cover near the camera (not sure how he did it)
you might want to try the software fix that is already available,many people said that their problem has been fixed after applying the software fix
but if you manage to open it can you report if there is any improvement in the signal attenuation in dbm?(using some app like wifi analyzer)
edit:found a video but how to open the back is not shown...
http://www.youtube.com/watch?v=cfCgPHw47Ho
There was another thread in this forum (can't find it now) written months back where someone was trying and achieved successes removing back off phone, as you say by heating the phone to melt glue
Sent from my HTC Desire S using XDA App
Hi I've looked at numerous videos,but none show removing the top,and I don't want to heat up my beloved phone!!
I'll flash a new Rom,radio and kernel tonite,then the software fix and see how it goes,unless one of the custom time already have it included,and report back
BR
bleach1 said:
Hi I've looked at numerous videos,but none show removing the top,and I don't want to heat up my beloved phone!!
I'll flash a new Rom,radio and kernel tonite,then the software fix and see how it goes,unless one of the custom time already have it included,and report back
BR
Click to expand...
Click to collapse
I think that you'll find that most of the Custom ROMS have the wifi fix already in them.
This was the other thread that I remember reading before, hope it is of help..
ben_pyett said:
I think that you'll find that most of the Custom ROMS have the wifi fix already in them.
This was the otThouher thread that I remember reading before, hope it is of help..
Click to expand...
Click to collapse
Thought they would cheers
Right i'm now on
coredroid desire s v1.1
radio 38.03.02.11_m (FLASHED SEPERATLY)
and mdj's kernel
I flashed v2 of the wifi fix after installing all of the above (even if the rom all ready instaled it) and i'm happy with result,even in the death grip i have 1 bar and that will do me fine,so no need to open up the phone
hope this helps any one out there
BR
Anybody else's gps connectivity generally crap? Seems to take for ever to connect then struggles to keep a connection.
Any known software conflicts? Running stock 2.35 rom.
No trees, walls, flying saucers in the way and Tried various gps info and fixer appear but to no avail.
Starting to really p*ss me off now.
Ta!
Sent from my HTC Desire S using XDA App
Yes, happens to me too. expecially when i go for walks. It takes reaally long time to load. Use Gpsfix ( Google it, Not able to post link because of post count) . It makes to process a lot faster.
khamoshpathak said:
Yes, happens to me too. expecially when i go for walks. It takes reaally long time to load. Use Gpsfix ( Google it, Not able to post link because of post count) . It makes to process a lot faster.
Click to expand...
Click to collapse
Be warned that gpsfix adds air push adverts to your phone. You may want to also instal add-on detector to find and remove them.
OP: Are you using a case? You may find that without root, you can't change the agps server location (mine was set to Asia by default) so it takes a while to lock pulling satellite info via 3g from the other side of the planet!
GPS Status and toolbox (which doesn't need root) forces an AGPS data download on startup and might help. Make sure 3g is on.
https://play.google.com/store/apps/details?id=com.eclipsim.gpsstatus2
Sent from my HTC Desire S using xda premium
Have observed that the GPS fix times are ROM dependent during my journey through many many excellent ROM's available for Desire S. I have even tried the AGPS fix which is recommended in the Dev section which was indeed helping to get a faster fix but the fix wasnt stable afterwards, especially while using apps like endomondo sports tracker..
The first ROM I saw that the GPS was excellent was in MIUI (GB) - without any AGPS or any other market apps or hacks I began to see a fix within 20 secs. Now, I'm presently on Reaper 2.2 (without AGPS fix) and the GPS continues to be excellent (<20 sec fixes).
I'm using ice cold sandwich with GPS+agps fix and find satellites in 3 seconds
Sent by my fingers to your head.
GPS fix issues can be as simple and HW-related as bad contact between the phone cover that includes GPS antenna (I guess it's the lower cover, but it might be an upper cover too), and the golden connector pin on the board. If you test all possible SW workarounds and they don't help - try to locate the antenna and make sure the connection is firm. Look for Vibrant GPS problems, they had such problem in the early batches.
For me the thread AGPS Patch Desire S 3.1 & 2.2 | GET BACK TO RAPID GPS LOCK, CAN LOCK ONTO MORE SATS helped a lot to get rapid GPS lock. Though, I'm not sure if root is needed for all installation methods. Good luck!
P.S.: The described patch is allready included in some custom roms like Endymion.
Jack_R1 said:
GPS fix issues can be as simple and HW-related as bad contact between the phone cover that includes GPS antenna (I guess it's the lower cover, but it might be an upper cover too), and the golden connector pin on the board. If you test all possible SW workarounds and they don't help - try to locate the antenna and make sure the connection is firm. Look for Vibrant GPS problems, they had such problem in the early batches.
Click to expand...
Click to collapse
The GPS and WiFi antennas are in the upper (camera lens) plastic cover, and, yes they use sprung pins to (hopefully) make connection. The phone antennas are in the lower (battery) cover.
I have found that many types of case massively deteriorate GPS reception of my phone. What puzzles me is why some users seem to be entirely unaffected; it's almost as if individual phones vary; even as an experienced engineer I cannot expalin it.
Since cases create mechanical pressure on the phone body and the contacts are very sensitive to their cover bending (they usually have a very light touch), it might be one of the reasons for reception deterioration. Sometimes even a hit of a falling phone can either destroy reception or improve it - saw it happening live on friend's Desire HD, it was very funny to see how the GPS that wouldn't lock properly for weeks, after the phone fell, started locking in 5 sec all of a sudden. Pure plastic cases shouldn't matter for reception otherwise, or at least I can't think of how can they possibly interfere.
By the way, Desire S' GPS is a bit on a weaker side - I compared it side-by-side to my MT4G, and it's always several lock seconds and a couple of locked satellites below. It should be plenty powerful for a good fast lock, though, and that's why I suspect disturbance on the HW side, rather than SW misconfiguration.
now that you guys are talking about cases, I was using a case mate barely there case before... long time ago gps fix was on the slow side (around a min).. but somewhere down the line of moving across ROM's I moved to MIUI GB (with the case still present) and the fix improved (without any AGPS patches or GPS fix apps).. now I dont use the case and have moved to Reaper CM7 based ROM and the GPS fixes are brilliant... looking at the build of Desire S I dont think that the contacts for GPS, wifi or phone antennas are at fault or can change with just a fall.. I can't pin the problem but I definitely feel removing the case has helped the gps fixes.
Jack_R1 said:
GPS fix issues can be as simple and HW-related as bad contact between the phone cover that includes GPS antenna (I guess it's the lower cover, but it might be an upper cover too), and the golden connector pin on the board. If you test all possible SW workarounds and they don't help - try to locate the antenna and make sure the connection is firm. Look for Vibrant GPS problems, they had such problem in the early batches.
Click to expand...
Click to collapse
Seems legit. By so far I am experiencing also constant GPS problem. It really might be the problem. I will make a try and let here know how it goes.
Forwox said:
Seems legit. By so far I am experiencing also constant GPS problem. It really might be the problem. I will make a try and let here know how it goes.
Click to expand...
Click to collapse
Clining contact did not help..
adding some wires to the antena (made some improvement)..
Than i orderd "new antena" for 8 eur form "Taiwan".
no may fix quick and with 12-18m an i does not lose fix anymore..
(and now i have working gps.. after 1 year of trying roms and waiting for better radio firmwares)
---------- Post added at 08:11 PM ---------- Previous post was at 07:38 PM ----------
fasty said:
What puzzles me is why some users seem to be entirely unaffected; it's almost as if individual phones vary; even as an experienced engineer I cannot expalin it.
Click to expand...
Click to collapse
You have first version of gps antenna which has been silently improved..
I bougt new antena (upper cover) and wifi antena is printed the sesame number, but gps antena has an number increased by 10. (which by my means, mean new version)
And with "new antena" i have reliably working gps now.
(htc service (here in SLO) wanted th have the phone one service for 14 day-s thats teh reason i didnt apply for warranty repair)
on stock rom gps is really slow..i have that experience before,actually one of the reason i rooted mine...now,got gps locked in less than 15 minutes...(my gps always turn off,on when want to use navigation only)
oTeMpLo said:
Clining contact did not help..
adding some wires to the antena (made some improvement)..
Than i orderd "new antena" for 8 eur form "Taiwan".
no may fix quick and with 12-18m an i does not lose fix anymore..
(and now i have working gps.. after 1 year of trying roms and waiting for better radio firmwares)
Click to expand...
Click to collapse
That's awesome! Could you please share a link to that item, please? I am really interested in that. I am still fighting with GPS. Sometimes it works, sometimes it don't...
Hello. i have a question. I have a problem with my mate 8. It's that that my GPS is not working (i don't get a GPS fix). I've sent my phone to the repair shop with guarantee, but they refused to fix it couse i have 2 slight dents in housing and apparently that is what is couses the GPS problem. (one dent is in area of volume buttons and the other is where the charging port is). It's really the dents that can couse this, or is the GPS itself? I could probably change the housing myself (they want me to pay 110€ for replacing it), but how is with replacing the GPS module itself? is it even possible? thank you in advance
its called an SoC (system on a chip) for a good reason, namely that the whole system is built into one chip or the same motherboard. so ud basically have to exchange the whole mobo ^^ maybe its just a bad gps antenna contact though...how did u get those dents?
Sent from my Huawei Mate 8 NXT-AL10
Ok, that sucks actually then
Is it possible to figure out if the gps is bad without changing the housing first? I tried AndoiTS GPS TEST and i get AGPS in orange. Does that mean that module is fine? (I added a screenshot).
Oh, and I've got the dents whit dropping my phone -.-
And another question. Where is the actual antenna? Or is the whole housing that works as antenna?
Hi. I bought the phone on the 8th October 2016. GPS was fully working. On the 10th, I updated as there is an update showing on my phone. After the update. I cannot get any GPS signal at all. This is a bad update.
Flash
I had same issue after I incorporated the KANGvip tools into AL10369 , just flash the cyst from another ROM like b200 or similar. If you don't know how then flash ROM to a working Rom with GPS. Extract the custom backup from twprp. Reload the nonworking ROM and flash only cyst and boom cops can find u after via gps lol
gps antenna fix
jbmc83 said:
its called an SoC (system on a chip) for a good reason, namely that the whole system is built into one chip or the same motherboard. so ud basically have to exchange the whole mobo ^^ maybe its just a bad gps antenna contact though...how did u get those dents?
Sent from my Huawei Mate 8 NXT-AL10
Click to expand...
Click to collapse
thanx to finding this thread i kept on searching
i recently changed the screen on my phone and since gps failed completely (wifi also seemed to be lesser)
as the phone lays on the screen, the copper nipple in top left corner is the contact the gps antenna has to make with the case.
i placed some paper beneath the element holding this niple, thus pushing it up - BINGO
i get a 3d fix in no time like before
also wifi connection improved
Where is this nipple? https://d3nevzfk7ii3be.cloudfront.net/igi/BPviD4orcNjWNIdi
geerthugo said:
thanx to finding this thread i kept on searching
i recently changed the screen on my phone and since gps failed completely (wifi also seemed to be lesser)
as the phone lays on the screen, the copper nipple in top left corner is the contact the gps antenna has to make with the case.
i placed some paper beneath the element holding this niple, thus pushing it up - BINGO
i get a 3d fix in no time like before
also wifi connection improved
Click to expand...
Click to collapse
Mate 8 GPS fixed !
Finally, after weeks of researches & tests I found the "nipple" or copper pin !!!
It's indeed the one on the top left once the screen is on the table. Either you find a way to put it back in position... without breaking it (the best way is probably with your nail) or you just put some Aluminium (a tiny sheet of aluminum folded several times to get 1mn maxi alu to allow the final winding) in the rectangular "hole" on top right (opposite) of the metal cover of MATE8.
I discovered the "right pin" while testing to put a small aluminium foil on several places of the main board (once opened naturally) AND using GPS TOOLS (playstore) ! you have to wait several seconds to get the signal or at least orange dots on the "radar". Better to test first such tool first with a smartphone where the GPS is working fine and compare both phones while changing the place of the aluminium. Nevertheless, I hope you would not have to repeat my tests as I will clearly show the right "copper pin" in an attached picture ...
Hoping that helps.
keyid said:
Where is this nipple? https://d3nevzfk7ii3be.cloudfront.net/igi/BPviD4orcNjWNIdi
Click to expand...
Click to collapse
Please read my answer below
[Q&A] WiFi stuck on turning on; MAC 02:00:00:00:00:00; G2 G3 G4 G5 Nexus5 Nexus 7 etc
Hi!
If you are reading this now, you are probably one of the unlucky fellows who's WiFi (and Bluetooth) stopped functioning, and if so, you are probably deperately searching for a solution/fix. I might have something for you, but first:
*** DISCLAIMER/WARNING ***
You yourself are exclusively responsible for whatever may (or may not) happen to your mobile device, to yourself or others. I am only giving hints/advices here that *MAY* help, but I will not take any responsability, nor will I provide any support, in absolutely *ANY CASE*, including, but not limited to: your problem not being solved or/and your mobile device becoming partially or completely broken. Let me be very clear: If you do anything to your device rendering it useless, destroying it, seriously or fataly injuring you or others, and then come blaming me or/and cry for help, I will point my index finger at you and laugh at you. Period.
If you are a impatient person and want to get straight to the point, jump right to section 6.
Table of Contents
0. Foreword
1. Description of the problem
2. Urgent advice
3. Things that didn't work
4. There is little hope
5. My most obvious advice
6. LET'S GET SERIOUS!
6.a Sellotape / Scotch tape
6.b Refrigerator / Freezer
6.c Oven
0. Foreword
Two or three months ago, one fine morning, the WiFi/BT of my LG G2 suddenly stopped working. Initially I thought this would be only one stupid annoying minor thingy, that I’d be able to solve it fast. I was wrong.
1. Description of the problem
When turning on the WiFi, it would just stay in "Turning on..." forever. Similar thing for Bluetooth: It would stay on for a few seconds and then turn itself off again after. (But then, who needs Bluetooth anyway, WiFi ist probably 100 times more important...). I have thoroughly searched the internet, and I found quite some videos with exactly the same problem (remove the two blanks from the links to watch):
h ttps://w ww.youtube.com/watch?v=fRGnQz1zUmw
h ttps://w ww.youtube.com/watch?v=4W8YJMDFM88
h ttp://w ww.dailymotion.com/video/x2cuyjt_nexus-5-turning-wifi-on-frozen-problem_tech
2. Urgent advice
I want to prevent you from wasting countless hours searching for a solution - I wasted so much of my time already, no need for you to repeat that. Therefore: *Please* be aware that there is a VERY HIGH PROBABILITY that this issue is being caused by a hardware defect. I can not speak for all devices of course, but keep in mind that the main reason I wasted so much time, was me beliving it was some software issue! See the next section for a glimpse of stuff I have tried without any success:
3. Things that *DIDN'T* work
01. Restarting WiFi/Bluetooth several times
02. Rebooting the phone
03. Turning airplane mode on/off several times
04. Slapping/hitting the phone (this was indeed suggested in a forum)
05. Using WiFi-Fixer apps
06. Resetting to factory settings
07. Upgrading to newest Android version
08. Fully drained the battery and left it uncharged for several hours
(Rooted the phone)
09. Deleting the /data/misc/wifi/wpa_supplicant.conf
10. Deleting the whole /data/misc/wifi folder
11. Creating a file named ".bdaddr" in /persist/bluetooth containing a MAC-Address in hexadecimal format
12. Creating a file named ".macaddr" in /persist/wifi containing a MAC-Address in hexadecimal format
13. Flashing several custom ROMs to it (CyanogenMod, ParanoidAndroid, ...)
14. Going back to stock ROM
15. etc. etc. etc.
16. Several combinations and permutations of the above
4. There is little hope
Again, as the cause of the problem is most likely a hardware issue, I don't recommend going through all the steps as described in the previous section; however, though none of the steps worked for me, this doesn't mean that none won't work for you neither; you might be luckier than I was. In that case, enjoy your restored WiFi and be happy.
5. My most obvious advice
You need to replace the motherboard (main board) of your device.
Honestly, if you can afford it and it doesn't cause too many inconveniences to you, you'll be better off by simply buying a new device. If you don't want to buy a new device, send it in for repairs. If you don't want to do that as well, you'll have to fallback to a DIY solution:
I. Buy a new main board for your device. Be careful to get exactly the right component for your specific model. If you dont find any shop selling those, there are plenty of individuals out there that own devices with broken displays. You dont need the displays, you need the motherboard. Buy one such broken device, and you'll have your main board replacement.
II. Replace your main board or let someone else do it for you
Continues below.
continuation
6. LET'S GET SERIOUS!
If you are reading this, you either didn't read or you decided not to follow my most obvious advice in section 5. So be it. If you want to carry on from here, be sure to re-read my disclaimer at the top of my post.
There are 3 DIY possible fixes for the WiFi problem - none is guaranteed. I will describe them from the most harmless to the most kamikaze/deadliest. All of them will require you to open your device; if you are not careful and damage any of the components inside, you will end up with a worse device than before - but hey, don't say I didn't warn you.
At this point we assume that the cause of the problem is a faulty solder joint of your WiFi IC. The goal is to try to restore that solder joint. To do that, you will have to:
I. Open your device
II. Find your main board and separate it from all connected plugs
III. Find / identify the WiFi IC chip on the main board. I recommend searching for a service manual for your device, or/and searching for a disassembly video for your device; you need to know which one of the chips on the main board is the WiFi one.
Once you have identified your WiFi chip, you have 3 options, which you may combine with each other, but I recommend to try them out one-by-one as follows:
6.a Sellotape / Scotch tape
You need to make sure that your WiFi chip is pressed against the main board (ideally, this ensures the broken contacts touch each other, solving the problem). The best way to achieve this, is to attach a series of tape strips on the top of the WiFi chip, causing it to be pressed against the main board by the surrounding cover/hull once you reassemble/close the device. The tape strips are just a suggestion, do whatever you find convenient as long as you ensure that the chip is pushed against the board at all times.
This method may solve the WiFi problem already. When you turn your device back on, give it some time (5-10 minutes) and reboot it a few times if the problem still persists. My own WiFi didn't function right away, but after a while it finally recovered - hurray!
6.b Refrigerator / Freezer
Instead of using the tape as described in 6.a, you may first try to put your motherboard in a fridge for a few hours/days. But make sure to put it there in a plastic bag, and avoid moisture as much as you can, specially when taking it out of the fridge. Make sure its completely dry before reassembling your device!
By the way, try the refrigerator option BEFORE you try the freezer option!
6.c Oven
If everything else fails, the oven might be your last chance. This is not a joke, but as you probably can assume, it is "All-In" i.e. highly risky. The theory behind this is that high temperature will cause defective solder joints to reflow, reconnecting and thus fixing the problem.
You should only try this as a matter of last ressort. Be warned that you may fully destroy your main board, and there is a high chance that you will. Also, you may cause serious injury to yourself or others. Make sure you make backups of your data first. DO NOT BAKE THE WHOLE DEVICE, ONLY THE MAIN BOARD. DO NOT BAKE THE BATTERY!!
If you are still reading:
I. pre-heat your oven to 385° Fahrenheit (196° Celsius)
II. put your main board in the oven, bake it there for 7 minutes
III. remove from the oven, let it cool down until every component of the board has room temperature
Finally, here is a video of a guy doing a similar thing, but with a heat gun:
h ttps://w ww.youtube.com/watch?v=A4n0j3uaS7E
Ok, this is all, I hope I could help you.
Good luck!
Summary
Hello all,
first of all, I want to thank brysclar and xbing6 for their valuable feedback! Thanks a lot guys! :good:
Now, in an effort to update this thread and in an effort of trying to summarize it in fewer words (my disclaimer above applies!):
- The described problem seems to affect mainly (all kinds of) LG devices
- The issue seems to be caused by a defective soldering of the Wi-Fi chip on the main board
- The defect seems to be induced by dropping or/and overheating the device; recharging the battery, big/long app or android updates or the flashing of custom roms could cause excessive heating
- brysclar pointed out that replacing the battery might solve the problem (I haven't tried this out myself, so I can neither deny nor confirm this)
- My recommended solution is 6.a - applying pressure on the Wi-Fi chip, pushing it against the main board, using tape stripes
- There is a video of a brasilean guy doing some similar, but using pieces of an old credit card instead of tape strips: https://www.youtube.com/watch?v=OJkdva2iOag BUT PLEASE NOTE THAT HE IS APPLYING THE PRESSURE ON A RANDOM SPOT, NOT DIRECTLY TO THE WIFI CHIP! It *may* work for you, but if it doesn't, find/identify your Wi-Fi chip and apply the pressure there
- If everything else fails, and only as a matter of last ressort, you may try what I have written in 6.c
So... this thread has over 500 views, but not one single reply.
Guys... what has your experience been? Have you tried anything out from the posts above, and if so, what was the result? Did it help you? Do you recommend anything? Has something else, not written here, worked for you?
There are a lot of people out there having the same problem. It would be great if you could give any feedback, share anything that helps the community.
Click to expand...
Click to collapse
I honestly didn't see this post before. You really covered every detail very well. So far, returning my G3 to stock and replacing the battery has fixed it for me. Weird. I know. I did try 90% of the things on your "things that don't work" list and you are correct. They don't work.
wlanmac 02/00/00/00/00, Bluetooth is OK
Hey, i just got an LG LS990 with same Wifi issue and i'm ready to try so WITNESS ME!
Thanks for an amazing and detailed post lml
Simply awesome.
I have similar issue with my Nexus 5x. It is QCA6174 hw 3.2 chip, lspci does not detect this chip any more. I am going to do a little bit investigation from device driver (cnss) perspective. It enables one GPIO to provide power to this WiFi chip, I will try read back this GPIO status to see if it is enabled. I do not have the schematics, I do not know how to check if power is supplied to this wifi chip.
lspci used to show below:
$ ./lspci
00:00.0 PCI bridge: Airgo Networks Inc Device 0300 (rev ff)
01:00.0 Network controller: Atheros Communications Inc. Device 003e (rev ff) (this is qca6174)
If kernel driver investigation does not reveal anything helpful, I will ask other guys to replace the chip.
I thought it is because of vendor partition is accidentally wiped out, maybe it is unlikely.
---------- Post added at 08:49 PM ---------- Previous post was at 08:40 PM ----------
As Bluetooth can not be turned either, I am tending to think this is hardware related as well. As described previously, I will see if I can check that gpio status.
investigating
xbing6 said:
I have similar issue with my Nexus 5x.
(...)
I am going to do a little bit investigation
Click to expand...
Click to collapse
Hi xbing, and thank you for your feedback! :good:
I am really curious and looking forward to hear the results of your investigation! I believe that in your case, too, the Wi-Fi/BT chip is not being supplied correctly due to a defective soldering. Note that I don't think that the chip itself is defective, only the contacts between the chip and the main board. So, before replacing the chip, I'd recommend to first try what I've written in 6.a (or check my update/summary above).
Keep us posted about everything you find out!
Sprint declined to fix my LS990 due to "water damage" being the reason for it not working, and wanted to charge me a $150 deductible for a $100 phone. Shimming the WiFi chip against the metal covering with some thermal pad I had lying around and adding a bit of sticky foam on top of the ribbon cable for the camera worked great! Much thanks!
Tomcat5 said:
Sprint declined to fix my LS990 due to "water damage" being the reason for it not working, and wanted to charge me a $150 deductible for a $100 phone. Shimming the WiFi chip against the metal covering with some thermal pad I had lying around and adding a bit of sticky foam on top of the ribbon cable for the camera worked great! Much thanks!
Click to expand...
Click to collapse
Any idea if thermal paste/grease could work?
unlikely
NavHur said:
Any idea if thermal paste/grease could work?
Click to expand...
Click to collapse
Hi NavHur,
since the problem is mostly caused by a loose Wi-Fi chip, respectively a defective solder joint, using thermal paste or grease is unlikely to help; again, what you need to do is to have your Wi-Fi chip pushed against your main board. You can use your imagination on how to accomplish this; what Tomcat5 described he did ultimately led to exactly having his chip being pressed against the board.
Of course you are free to try whatever you want - if you find new solutions please post some feedback.
Good luck.
NimbleWeasel said:
Hi NavHur,
since the problem is mostly caused by a loose Wi-Fi chip, respectively a defective solder joint, using thermal paste or grease is unlikely to help; again, what you need to do is to have your Wi-Fi chip pushed against your main board. You can use your imagination on how to accomplish this; what Tomcat5 described he did ultimately led to exactly having his chip being pressed against the board.
Of course you are free to try whatever you want - if you find new solutions please post some feedback.
Good luck.
Click to expand...
Click to collapse
Thanks you so much, I placed a small piece of plastic above the wifi chip and one next to the camera lens. Now the wifi works fine. However my screen was pushed up so it bended a little. The faulty thing was my battery, not the added plastic. I compared mine with the one of a friend, mine was 1 mm bigger. (also with the battery of my friend's g3 the screen was fine)
I'll be changing it soon.
same problem as u but sometimes wifi works(mainly fully charged) and sometimes dont
i have lg g2 D802 model. It had a wifi problem as u shown in your videos,my phone also behaves same like yours but sometimes it works normally like while charging,works like 2 or 3 times a day(for 5-10 min).please tell me whether my phone got ic problem or software issue
Pratap94 said:
i have lg g2 D802 model. It had a wifi problem as u shown in your videos,my phone also behaves same like yours but sometimes it works normally like while charging,works like 2 or 3 times a day(for 5-10 min).please tell me whether my phone got ic problem or software issue
Click to expand...
Click to collapse
Hi Pratap94,
nobody, neither here in this forum nor elsewhere in the internet, will be able to give you a reliable answer without having a *physical* look at your phone. Nobody.
However, I can give you my opinion, based on the stuff you wrote: The fact that it works normally sometimes, specially while charging (probably it heats up in the process?), indeed seems to indicate a hardware issue. I believe you have a loose Wi-Fi chip i.e. a defective solder joint, like I had on my LG G2 D802 as well. I solved my problem by doing the stuff I described in 6.a.
Good luck.
Thank you so much
NimbleWeasel said:
Hello all,
first of all, I want to thank brysclar and xbing6 for their valuable feedback! Thanks a lot guys! :good:
Problem solved good bless you!! the problem is fix in that youtube video XD
Click to expand...
Click to collapse
Sadly step 6.a did not help me. Well, it worked for first 5-10 minutes and then back again.
Olzhas18 said:
Sadly step 6.a did not help me. Well, it worked for first 5-10 minutes and then back again.
Click to expand...
Click to collapse
Hi Olzhas18,
that might be an indication that your WiFi chip is still a bit loose and is not sitting tight enough on the main board. On LG G2, it is difficult to push the chip against the board because it's covered by a metal cover...
Also, did you check out this video: https://www.youtube.com/watch?v=OJkdva2iOag ?
Good luck!
NimbleWeasel said:
Hi Olzhas18,
that might be an indication that your WiFi chip is still a bit loose and is not sitting tight enough on the main board. On LG G2, it is difficult to push the chip against the board because it's covered by a metal cover...
Also, did you check out this video: https://www.youtube.com/watch?v=OJkdva2iOag ?
Good luck!
Click to expand...
Click to collapse
Thank you this tip and this whole thread. I have seen this video, but still the same effect. 5-10 minutes, I can rean some news and back to flashing. I'm going to buy Huawei Honor 8 soon, it was the last chance to recover my G4. I doubt I will purchase any other phone from LG.
Same boat
But bluetooth working
In cm roms also wifi tethring can be onn
But u cnt turn onn wifi
I had the same issue, can't turn on Wifi after factory reset.
I turn off my device off after one hour and reboot wifi was OK but when I want to upgrade some apps iwifi turn of again and my phone reboot with no SIM card.
I do "6.a Sellotape / Scotch tape" + a creedit card cut with this video https://www.youtube.com/watch?v=6_0jzp65eLY#t=73.319872
My LG G2 works fine
Hi, I've got an issue with my Mi5S Plus phone.
It finds only 4-5 sattelites via GPS while other phone finds 21.
Bluetooth works within 2-3 meters only.
Wifi 2.4 Hz works in 5-6 meters max and shows low signal strength.
Meanwhile Wifi 5 Hz works pretty well.
LTE works ok.
It's chinese phone with Global ROM 9.6.2.0 installed.
Mac adress in about phone is not empty.
Is that hardware or software issue?
Looks like antena issue but where is it and where are antena connectors in Mi5S Plus?
Will flash of ROM help? (I did not try it yet)
Any help is highly appreciated! I face such issue for the first time and searching the internet does not help.
open the phone, the antenna for anything except cellular are the tiny pogo connector that should be in contact with the respective pads in the back case...
clean the back case's pad for the respective contact points and try it again...
@dogrishin were you able to fix it?
Crescendo Xenomorph said:
@dogrishin were you able to fix it?
Click to expand...
Click to collapse
No I did not try it yet. I will definitely update with results. Thanks for your support, Crescendo!
Great Thanks!
Crescendo Xenomorph said:
@dogrishin were you able to fix it?
Click to expand...
Click to collapse
Thank you Crescendo again! I finally succeeded to fix it.
Chinese seller broke connector in the left upper corner of PCB when he disassembled phone to flash Global ROM via ETL loader I suppose.
I had to solder another connector and so now it's finally working as it should: Wifi 2.4, bluetooth, GPS signals are strong.
So it was 100% hardware issue, not related to software.
For other guys with same issue I advice to disassemble according to video on YouTube:
"Как разобрать Xiaomi Mi5s Plus (2016070) Разборка и ремонт"
And if you have same issue, bring it to repairman so he will solder you another connector fast and cheap.
dogrishin said:
Thank you Crescendo again! I finally succeeded to fix it.
Chinese seller broke connector in the left upper corner of PCB when he disassembled phone to flash Global ROM via ETL loader I suppose.
I had to solder another connector and so now it's finally working as it should: Wifi 2.4, bluetooth, GPS signals are strong.
So it was 100% hardware issue, not related to software.
For other guys with same issue I advice to disassemble according to video on YouTube:
"Как разобрать Xiaomi Mi5s Plus (2016070) Разборка и ремонт"
And if you have same issue, bring it to repairman so he will solder you another connector fast and cheap.
Click to expand...
Click to collapse
I cannot post URLs as I an novice here, you can see them by these links:
_http://i66.tinypic.com/33couip.png
_http://i68.tinypic.com/2jbwo6q.png
_https://www.youtube.com/watch?v=iTmSfh91lc4
thanks for the clear photo & pinpoint accuracy.
I can only guess the connectors coz they're plenty on top part of the phone... [emoji38]
Mine's not broken but the GPS (only the GPS) signal is weak... weaker than my wife's, same model same configs.
it all happened after I opened the phone for cleaning..., maybe the pin isn't making good contact with the antenna, I'll reopen it tom & try to bend it forward carefully...
again thanks for the clear explanation & photo...
glad it's all ok for you...
Sent from my MI 5s Plus using Tapatalk
@dogrishin is it possible to repost the photos of the connector that you have fixed, they're gone from tinypic (perhaps upload to imgur or somewhere)
@Crescendo Xenomorph have you figured out which connector specifically is the GPS antenna?
I have the same problem after I had to disconnect and re-connect the battery. I haven't broken any pins or replaced anything in the phone but after putting it back together the GPS signal is insanely weak. Takes forever for a position fix and keeps losing it after. Also Wi-Fi is dead one wall away from the router. I've carefully bent all the pins a bit towards the back-case today and had no great improvement.
I think it's the second one from the top right, coz I broke mine & the wifi is gone...
Had to get it replaced to makewifi work again, but my take is usually just fix all connectors inside since I can't be sure....
@kaboom83 sorry for sooo late reply, but I could not find original photos....so now I just accidentally have found them and reuploaded to imgur. Here they are
https://imgur.com/a/ejfjqGb