Related
I got the tablet "unlocked:, Rooted, And running clockworkmod recovery. I had over the air update to 4.1 before all this but had no issues. I downloaded a ROM for 4.1, and when I rebooted into CWM I went to wipe my data and thats when it happened. The data wipe froze. I ended up having to forcfully turn it off. Then I got bootloop. I can get into cwm but I cant find my ROM to flash it. So im literally stuck. Is there a One Click revert to stock I can use? Or anything? Many thanks to anyone who can help. Note: this is my 1st tablet - Asus Transformer tf300t
jburke90 said:
I got the tablet "unlocked:, Rooted, And running clockworkmod recovery. I had over the air update to 4.1 before all this but had no issues. I downloaded a ROM for 4.1, and when I rebooted into CWM I went to wipe my data and thats when it happened. The data wipe froze. I ended up having to forcfully turn it off. Then I got bootloop. I can get into cwm but I cant find my ROM to flash it. So im literally stuck. Is there a One Click revert to stock I can use? Or anything? Many thanks to anyone who can help. Note: this is my 1st tablet - Asus Transformer tf300t
Click to expand...
Click to collapse
I also made a backup before everything but I cant restore it. It says MD5 Mismatch. Im really stuck here...
so try to load your rom to sd card. then install from that?
naelme said:
so try to load your rom to sd card. then install from that?
Click to expand...
Click to collapse
I have no access to my sd card. The ROM I downloaded previously does not show up in CWM.
You can't flash it again from cwm by redowloding, then putting on your SD card then munt in it?
U could reflash your unit with stock ROM using fastboot. I just unbricked my unit doing that after 5 days of fighting.
This is what I did, I downloaded job update from Asus then moved the blob to c/fast boot, loaded unit to fast boot then typed
fastboot -i 0x0B05 flash system blob
But make sure our boot loader is 10.4 or it will signature mismatch, so down load the appropriate boot loader .
That's what I did at least and my unit is working again.
naelme said:
You can't flash it again from cwm by redowloding, then putting on your SD card then munt in it?
U could reflash your unit with stock ROM using fastboot. I just unbricked my unit doing that after 5 days of fighting.
Click to expand...
Click to collapse
What would my commands be to do this? Thanks
jburke90 said:
What would my commands be to do this? Thanks
Click to expand...
Click to collapse
I used
fastboot -i 0x0B05 flash system blob
read above edit.
i found the info here but had to tweak because once you upgrade bootload to 10.4 there is no going back it seems.
http://www.theandroidsoul.com/how-to-restore-asus-transformer-tf300t-back-to-stock/
you will lose your cwm, but you can re implement it when your done.
naelme said:
You can't flash it again from cwm by redowloding, then putting on your SD card then munt in it?
U could reflash your unit with stock ROM using fastboot. I just unbricked my unit doing that after 5 days of fighting.
This is what I did, I downloaded job update from Asus then moved the blob to c/fast boot, loaded unit to fast boot then typed
fastboot -i 0x0B05 flash system blob
But make sure our boot loader is 10.4 or it will signature mismatch, so down load the appropriate boot loader .
That's what I did at least and my unit is working again.
Click to expand...
Click to collapse
Can I use a custom ROM zip and get it from that? My internet is really slow tonight and 300mb is just crawling so downloading a stock ROM will take me another hour or so.... I am rooted if that helps.
jburke90 said:
Can I use a custom ROM zip and get it from that? My internet is really slow tonight and 300mb is just crawling so downloading a stock ROM will take me another hour or so.... I am rooted if that helps.
Click to expand...
Click to collapse
it has to match your current bootloader. if you updated jellybean your bootloader version is 10.4 and that is irreversible. so find out if that rom works on your current boot loader. once you go jb you can't go back.
in short. idk. if you want your unit install a rom that is made for your bootloader. idk custom roms. i use stock os rooted.
naelme said:
it has to match your current bootloader. if you updated jellybean your bootloader version is 10.4 and that is irreversible. so find out if that rom works on your current boot loader. once you go jb you can't go back.
in short. idk. if you want your unit install a rom that is made for your bootloader. idk custom roms. i use stock os rooted.
Click to expand...
Click to collapse
It is a JB ROM so it seems like it would work (fingers crossed).
jburke90 said:
It is a JB ROM so it seems like it would work (fingers crossed).
Click to expand...
Click to collapse
let me know. if the bootloader is 10.4 it should.
jburke90 said:
It is a JB ROM so it seems like it would work (fingers crossed).
Click to expand...
Click to collapse
Well this didn't work. I found the boot.blob and did what everything said to do but still boot loops. Not sure if it was because its not stock or not. I did notice that when I put in the command to reboot, it said it reboot but the tablet did nothing..... so is there a chance that it didn't even flash? It did seem very fast.
Verify boot loader version and use stock ROM.......
Find working custom ROM. Don't brick it
naelme said:
Verify boot loader version and use stock ROM.......
Click to expand...
Click to collapse
I will do that tomorrow. How do I verify my boot loader though?
If anybody need recovery, full worked with new 4.1.1 JB get it here.
Moderator Edit:
Link removed as it is proven this recovery can damage your device.
Gigabyte0 said:
If anybody need recovery, full worked with new 4.1.1 JB get it here
Click to expand...
Click to collapse
What exactly is that, where is it from?
Recovery shouldn't have anything to do with installed Android version.
Sent from my GT-I9000 using xda app-developers app
pawitp said:
What exactly is that, where is it from?
Recovery shouldn't have anything to do with installed Android version.
Sent from my GT-I9000 using xda app-developers app
Click to expand...
Click to collapse
If I were to guess, it's a different CWM recovery using JB Kernel?. It probably came from 4pda.ru which is a russian site. HAs a lot of android tablet stuff.
Just a guess. Might research it a little and see what I come up with.
It's not exactly the easiest site to navigate through.
MD
Moscow Desire said:
If I were to guess, it's a different CWM recovery using JB Kernel?. It probably came from 4pda.ru which is a russian site. HAs a lot of android tablet stuff.
Just a guess. Might research it a little and see what I come up with.
It's not exactly the easiest site to navigate through.
MD
Click to expand...
Click to collapse
I don't exactly see the need of a new recovery, since it works independent of the Android version. An "unknown" recovery would be possibly unsafe as well.
Gigabyte0 said:
If anybody need recovery, full worked with new 4.1.1 JB get it here
Click to expand...
Click to collapse
this one save´d my TAB!!!
i was able to reanimate it after i messed up ..
THX a lot
pawitp said:
I don't exactly see the need of a new recovery, since it works independent of the Android version. An "unknown" recovery would be possibly unsafe as well.
Click to expand...
Click to collapse
This is not "unknown" recovery. This 6.0.1.1 with kernel from bootloader JB (boot.img)
And this recovery normal mount all partition, make backup-restore and other function.
For ICS bootloader need original recovery 6.0.1.1
For JB bootloader my recovery, rebuilding from original JB bootloader and CMW recovery
Gigabyte0 said:
This is not "unknown" recovery. This 6.0.1.1 with kernel from bootloader JB (boot.img)
And this recovery normal mount all partition, make backup-restore and other function.
For ICS bootloader need original recovery 6.0.1.1
For JB bootloader my recovery, rebuilding from original JB bootloader and CMW recovery
Click to expand...
Click to collapse
You should give some info when posting, otherwise it is "unknown".
The boot.img contains the kernel not the bootloader. The kernel source is yet to be released by Acer and we don't know if Acer has blocked the dangerous emmc wipe command (which will randomly brick tablets, the more you wipe, the riskier you are) like I did on my kernel or not.
This is not "unknown" recovery. This 6.0.1.1 with kernel from bootloader JB (boot.img)
And this recovery normal mount all partition, make backup-restore and other function.
For ICS bootloader need original recovery 6.0.1.1
For JB bootloader my recovery, rebuilding from original JB bootloader and CMW recovery
Click to expand...
Click to collapse
But what it does not, it does not flashes. Freezes and hangs. Have my tab after 30 minutes. removed and restarted, now it hangs in APX mode. Do you have a solution for this?
Hi There
after i recovered my Tab to work, i´ve done a flash with this Recovery and it freezes.
After this i only was able to turn off the Decvice.
Now it seem´s that i can´t turn on, Black Screen, no LED, only thing the Computer tells an USB Device want´s to install.
Try to install APX drivers an failed.
some ideas?
meier2009 said:
Hi There
after i recovered my Tab to work, i´ve done a flash with this Recovery and it freezes.
After this i only was able to turn off the Decvice.
Now it seem´s that i can´t turn on, Black Screen, no LED, only thing the Computer tells an USB Device want´s to install.
Try to install APX drivers an failed.
some ideas?
Click to expand...
Click to collapse
"This recovery" meaning mine or Gigabyte0's?
If you're in APX mode, you're out of luck and the service center will probably need to replace your mainboard.
"This recovery" meaning mine or Gigabyte0's?
If you're in APX mode, you're out of luck and the service center will probably need to replace your mainboard.
Click to expand...
Click to collapse
Yes, it meant the version of Gigabyte0. Does not sound good.
Spread the word please:
ONLY USE PAWITP'S RECOVERY UNLESS YOU WANT A BRICKED TABLET
If pawitp's recovery is not working for you, then wait. The Recovery released by Gigabyte0 and found on 4PDA is built with Acer's kernel and Acer still has not fixed the brick bug!
Again, do NOT use Gigabyte0's recovery!
NoThrills said:
Spread the word please:
ONLY USE PAWITP'S RECOVERY UNLESS YOU WANT A BRICKED TABLET
If pawitp's recovery is not working for you, then wait. The Recovery released by Gigabyte0 and found on 4PDA is built with Acer's kernel and Acer still has not fixed the brick bug!
Again, do NOT use Gigabyte0's recovery!
Click to expand...
Click to collapse
And I will concurr. So far, Pawitp's has caused 0 issues.
Why somebody would want to install an unheard of recovery, with absolutely 0 information about it, is just asking for trouble.
I'll toss in a note to the FSM, and have him deal with Gigabyte0 on what to do with this link.
MD
Moscow Desire said:
And I will concurr. So far, Pawitp's has caused 0 issues.
Why somebody would want to install an unheard of recovery, with absolutely 0 information about it, is just asking for trouble.
I'll toss in a note to the FSM, and have him deal with Gigabyte0 on what to do with this link.
MD
Click to expand...
Click to collapse
Maybe you can also let this know on 4PDA.ru, as I am not Russian (and you are) you can probably explain it better:
In the Acer 3.0 Android kernel the command MMC_CAP_ERASE, which has caused all the old bricks, is still present. At least it is in the A110 3.0 kernelsource and I have no reason to believe they would remove it in the A700 3.0 kernelsource but not in the A110 one.
When this command exists in the kernel, and the Recovery also allows it (Recovery can also disable it, but the current A700 recovery doesn't do that), you are almost guarantueed a brick.
If you could translate that to 'the Russians' I guess we can save a few more people from bricking.
Thread Closed
hi, iam new user of TF300t, i installed the Energy.TF201.or.TF300..JB.03.18.2013.( i dont remebmer is the STOCKED or THEMED) ! after that i wanted to install BAKED_TF300T_BB-8, but the device stay on the boot menu! so what i did , installed the 6.0.2.3 CWM ( [CWM][6.0.2.3 / 5.5.0.4] Official CWM Recovery for JB/ICS + ROOT) ! after that i rebooted the device. Stock in the Asus LOGO! After i rebboted by holding the power menu and volume down, i choosed the wipe option ( i dont know why) and from tht time, it rebbots only in the 6.0.2.3 CWM what ever i do!
For 5 days, i have tried to flash via fastboot twrp.blob, i have pushed the firmware from asus to /sdcard and flashed via fastboot always, i have tried and read similaire problems! didt succed! i have always the message tht Can not mount sdcard! cant mound E/data! cant mount anythingg!! What ever i do, always reboot to this CWM !!!!!
please any one help me!!!!!!! thanks a lot!!!
You have installed an incompatible older custom recovery on the 4.2.1 bootloader. What you should have one is downgraded the bootloader from the energy thread to 4.1.1. You didn't need to downgrade your recovery.
Anyway I think you have bricked now.
sbdags said:
You have installed an incompatible older custom recovery on the 4.2.1 bootloader. What you should have one is downgraded the bootloader from the energy thread to 4.1.1. You didn't need to downgrade your recovery.
Anyway I think you have bricked now.
Click to expand...
Click to collapse
but i can use adb commands, and fastboot commande ( except tht i have waiting for device each time) so its bricked for EVER?!
You appear to have the same brick as everyone else. Caused by an older recovery on the latest bootloader.
If you can get fastboot to accept a lower bootloader or get it to accept TWRP 2.4.4.0 you should be able to recover but as you said it won't accept anything........
sbdags said:
You appear to have the same brick as everyone else. Caused by an older recovery on the latest bootloader.
If you can get fastboot to accept a lower bootloader or get it to accept TWRP 2.4.4.0 you should be able to recover but as you said it won't accept anything........
Click to expand...
Click to collapse
yes, it accept nothing! even if i downgrade to ics to apply the nvflash its worse! so should i say bye forever to my tf300t?!! if yes, which tablets tht cn be less bricked than others? thks a lottt! wht would u do if u were at my place? thksssssssssss
buy a new mainboard (motherboard)
Sent from my TF300T using xda app-developers app
How are you trying to downgrade? Can you get to the booloader? If yes, try this:
In bootloader, wipe data
Reboot into bootloader
Then, using fastboot, flash system blob from Asus stock ROM using fastboot (fastboot -i 0x0b05 flash staging blob)
If that succeeds, flash appropriate TWRP from bootloader using fastboot, then flash bootloader compatible ROM
If it only (re)boots to recovery, then you'll have to hang in there until a solution is invented. Until that time, you're bricked
---------- Post added at 10:08 PM ---------- Previous post was at 10:06 PM ----------
On a side note - can I flash 4.1 compatible ROMs on a 4.1 bootloader using the newest patched 2.4.4.0 TWRP without getting into trouble?
Ti2 said:
How are you trying to downgrade? Can you get to the booloader? If yes, try this:
In bootloader, wipe data
Reboot into bootloader
Then, using fastboot, flash system blob from Asus stock ROM using fastboot (fastboot -i 0x0b05 flash staging blob)
If that succeeds, flash appropriate TWRP from bootloader using fastboot, then flash bootloader compatible ROM
If it only (re)boots to recovery, then you'll have to hang in there until a solution is invented. Until that time, you're bricked
---------- Post added at 10:08 PM ---------- Previous post was at 10:06 PM ----------
On a side note - can I flash 4.1 compatible ROMs on a 4.1 bootloader using the newest patched 2.4.4.0 TWRP without getting into trouble?
Click to expand...
Click to collapse
thanks for yr reply ill try even im bricked! ill by another tabelt but not asus, maybe samsung, i have a GS2 , i install every thing without problem, i think there tables dont brick easly! true?
You wouldn't be bricked if you had read the instructions and followed them to the letter (and ask questions when unsure).
With that in mind - you can just as easily brick any device.
Ti2 said:
You wouldn't be bricked if you had read the instructions and followed them to the letter (and ask questions when unsure).
With that in mind - you can just as easily brick any device.
Click to expand...
Click to collapse
No that's just wrong for a bunch of people. At the time I did it. There was no warning, no indication of any problems. Just decided to do it at the wrong time. If it was 1 day later, I would have seen the bricked threads or had the patched TWRP.
sevenalive said:
No that's just wrong for a bunch of people. At the time I did it. There was no warning, no indication of any problems. Just decided to do it at the wrong time. If it was 1 day later, I would have seen the bricked threads or had the patched TWRP.
Click to expand...
Click to collapse
Wrong? No.
Harsh? Yes.
Read read read. Learn learn learn. Then read some more. When unsure, ask questions. Don't just try, then read the manual tot learn how you screwed up...
I am unsure tot flash 4.1 bootloader based roms through the 4.2 patched TWRP. I am NOT just going to try, I am awaiting an answer for 3 days now.
Is a Tab(2) as easily to brick as a Transformer? Yes it is.
sevenalive said:
No that's just wrong for a bunch of people. At the time I did it. There was no warning, no indication of any problems. Just decided to do it at the wrong time. If it was 1 day later, I would have seen the bricked threads or had the patched TWRP.
Click to expand...
Click to collapse
true wht u said !
Not trying to be harsh but that's why they call it "bleeding edge". You take the risks if you cannot be patient.
Sent from my SCH-I510 using xda app-developers app
hi,
did you try to use TWRP 2.4.4.0 - 4.2 this is the only one can read and write the sdcard on my TF300t after update to 4.2.1 good luck
lk2l said:
hi,
did you try to use TWRP 2.4.4.0 - 4.2 this is the only one can read and write the sdcard on my TF300t after update to 4.2.1 good luck
Click to expand...
Click to collapse
no succes to flash anything! always back to cwm 6.0.2.3...
when you type fastboot devices or adb devices can you see the device?
lk2l said:
when you type fastboot devices or adb devices can you see the device?
Click to expand...
Click to collapse
i can see this 0123456789ABCDEF, thts not the device name sure! isn't ? i can flash via fastboot ( sending ok, flashing ok) i flashed the blob file tht comes with the Asus frimwork 10.6.1.8 but nothing, always i go back to the 6.0.2.3 CWM! i flashed the twrp.blob file! same thing! im turning in an empty circle! good for trash??
depend if the code you write is only an example probably it is, is the device code.
don't worry until you can see the device you should be able to fix it... only thing is to found how
lk2l said:
depend if the code you write is only an example probably it is, is the device code.
don't worry until you can see the device you should be able to fix it... only thing is to found how
Click to expand...
Click to collapse
hope so! thkssssssssssssssssssssss
can you tell me which procedure you do to flash the recovery?
here you can found all I have used to flash my tf300t with the bootloader 4.2.1
fastboot+twrp recovery 2.4.4.0-4.2
is possible your fastboot dosen't work correctly?
I am on the new 4.2 bootloader and TWRP 2.4. Last night I went to upgrade TWRP. I chose the TWRP file named twrp-2.5.0.0-tf300t-4.2.blob. I renamed the file twrp.blob and pushed it out via fast boot. When done I rebooted via fastboot, and then rebooted into recovery.
Now something is not right, twrp is split into two screens horizontily and shows the lock picture on both. I have to power cylce to get back to Andriod. Where did I go wrong? Should I have chosen the .img file?
Ok I think think I realized there has been a second 4.2 bootloader update from Asus and that's my problem. Is that right?
Sent from my GT-N7100 using Tapatalk 2
yes.
A lot of people have soft bricked their device because of this.
Yeah from what I've read twrp 2.5.0.0-4.2 will only work correctly on JB bootloader 10.6.1.15.3, not sure yet if twrp 2.4.4.0-4.2 works on 10.6.1.15.3.
I have no issues with twrp 2.5.0.0-4.2 on JB 10.6.1.15.3
10.6.1.8 - TWRP 2.4.4.0-4.2
10.6.1.15.3 - TWRP 2.5.0.0-4.2
pjc21 said:
Yeah from what I've read twrp 2.5.0.0-4.2 will only work correctly on JB bootloader 10.6.1.15.3, not sure yet if twrp 2.4.4.0-4.2 works on 10.6.1.15.3.
I have no issues with twrp 2.5.0.0-4.2 on JB 10.6.1.15.3
10.6.1.8 - TWRP 2.4.4.0-4.2
10.6.1.15.3 - TWRP 2.5.0.0-4.2
Click to expand...
Click to collapse
So I have 10.6.1.8 and installed 2.5.0.0 and am experiencing the same problem (the noob proof guide wasn't very noob proof apparently). How would I go about putting on the correct version?
EDIT: So I just took the plunge and reflashed the correct version which I found http://techerrata.com/file/twrp2/tf300t/openrecovery-twrp-2.4.4.0-tf300t-4.2.blob here. I was initially worried because I wasnt sure if I could just flash over and downgrade versions...it worked for me, and TWRP is currently making a backup and is full screen and running.
TWRP GONE Wrong
Tunameltsalad said:
So I have 10.6.1.8 and installed 2.5.0.0 and am experiencing the same problem (the noob proof guide wasn't very noob proof apparently). How would I go about putting on the correct version?
EDIT: So I just took the plunge and reflashed the correct version which I found http://techerrata.com/file/twrp2/tf300t/openrecovery-twrp-2.4.4.0-tf300t-4.2.blob here. I was initially worried because I wasnt sure if I could just flash over and downgrade versions...it worked for me, and TWRP is currently making a backup and is full screen and running.
Click to expand...
Click to collapse
Ok I may be late but I am having the same problem I rooted my tf300t with motochopper not hard at all but once I tried to flash twrp I have two screens. I downloaded what the same blob file you did but not sure the command to type so I typed -i 0x0B05 flash recovery twrp.blob. What should I type?
dmont2006 said:
Ok I may be late but I am having the same problem I rooted my tf300t with motochopper not hard at all but once I tried to flash twrp I have two screens. I downloaded what the same blob file you did but not sure the command to type so I typed -i 0x0B05 flash recovery twrp.blob. What should I type?
Click to expand...
Click to collapse
Which bootloader do you have?
cmendonc2 said:
Which bootloader do you have?
Click to expand...
Click to collapse
same problem 4.2 bootloader
i update to twrp v2.6.3.0 to try and didnt work to same as 2.0.7.1
its annoying because the (normal ) working version was around 2.0....
i can go back by using terminal emulator and twrp blob instal but i want to instal cm11 so i need latest or higher than v2.6.3.0
i dont know how to make it work .
wouttii said:
same problem 4.2 bootloader
i update to twrp v2.6.3.0 to try and didnt work to same as 2.0.7.1
its annoying because the (normal ) working version was around 2.0....
i can go back by using terminal emulator and twrp blob instal but i want to instal cm11 so i need latest or higher than v2.6.3.0
i dont know how to make it work .
Click to expand...
Click to collapse
Hi, ive been searching recently but can't seem to find out how to update the bootloader. Dont hate me:'( trust me ive tried to find it myself but id really appreciate if someone could give me a link or tell me how. Thanks in advance.
How do I Get to TWRP 2.4.4.0 when I Install TWRP 2.5.0.0?
It cant recognize SDCard and i Want back to old version.
MrZi said:
How do I Get to TWRP 2.4.4.0 when I Install TWRP 2.5.0.0?
It cant recognize SDCard and i Want back to old version.
Click to expand...
Click to collapse
How are you trying to install it? Recoveries are installed by bootloader and should be in the same directory as 'fastboot.exe'.
Also have you made sure you've got the right recovery for you boot loader version (ICS, JB or 4.2)?
psjw12 said:
How are you trying to install it? Recoveries are installed by bootloader and should be in the same directory as 'fastboot.exe'.
Also have you made sure you've got the right recovery for you boot loader version (ICS, JB or 4.2)?
Click to expand...
Click to collapse
A was download WW_V10.6.1.15.3 from Asus page and Recovery openrecovery-twrp-2.4.4.0-tf300tg-JB.img.
How Can I flash it to work my Asus good? It only starts to recovery.
MrZi said:
A was download WW_V10.6.1.15.3 from Asus page and Recovery openrecovery-twrp-2.4.4.0-tf300tg-JB.img
Click to expand...
Click to collapse
Have you every upgraded your tablet to 4.2? If so DO NOT flash that recovery. It will brick your device.
---------- Post added at 11:41 PM ---------- Previous post was at 11:37 PM ----------
MrZi said:
How Can I flash it to work my Asus good? It only starts to recovery.
Click to expand...
Click to collapse
If you look at this thread http://forum.xda-developers.com/showthread.php?t=1845377
In Part 3, that explains how to flash recovery.
I personally wouldn't downgrade TWRP, is there a reason you want to downgrade?
I was upgrade to 4.2 JB Stock
How Can I get starts normal System?
MrZi said:
I was upgrade to 4.2 JB Stock
How Can I get starts normal System?
Click to expand...
Click to collapse
What do you mean by 'normal system'?
Again DO NOT flash that recovery.
You've got a 4.2 bootloader, but that recovery is for 4.1. If you apply it you WILL brick your device.
psjw12 said:
What do you mean by 'normal system'?
Again DO NOT flash that recovery.
You've got a 4.2 bootloader, but that recovery is for 4.1. If you apply it you WILL brick your device.
Click to expand...
Click to collapse
I haveCustom ROm with 4.1 and want to install another Rom with 4.2
I was install JB 4.2 from Asus page and Recovery : openrecovery-twrp-2.5.0.0-tf300tg-JB.blob
And that TWRP didnt recognize SDcard. I was wipe data and my Asus still starts to recovery.
When I adb reboot to bootloader and push OS its starts normal to OS.
I want to restore to normal boot to JB 4.2, how Can I do it?
MrZi said:
I was install JB 4.2 from Asus page and Recovery : openrecovery-twrp-2.5.0.0-tf300tg-JB.blob
Click to expand...
Click to collapse
Whilst you're on Android 4.1, you can flash openrecovery-twrp-2.5.0.0-tf300tg-JB.blob
But once you've upgraded to Android 4.2 from ASUS you must use recovery openrecovery-twrp-2.5.0.0-tf300tg-4.2.blob
MrZi said:
And that TWRP didnt recognize SDcard. I was wipe data and my Asus still starts to recovery.
When I adb reboot to bootloader and push OS its starts normal to OS.
I want to restore to normal boot to JB 4.2, how Can I do it?
Click to expand...
Click to collapse
Unfortunately I can't help you with why the SD Card didn't get recognised. I'm sure someone else will help.
There are guides around on this forum; rather than flashing the official ASUS update via recovery, it can also be done by bootloader. I think it involves 'system.blob' to be pushed to the device, and the update ZIP file to be on the /sdcard/ directory.
psjw12 said:
What do you mean by 'normal system'?
Again DO NOT flash that recovery.
You've got a 4.2 bootloader, but that recovery is for 4.1. If you apply it you WILL brick your device.
Click to expand...
Click to collapse
I was install by fastboot recovery openrecovery-twrp-2.5.0.0-tf300tg-4.2.blob but it still not recognize sdcard internal and external, why?
I was install SW from Asus page by fastboot and fastboot bootloader.
Device starts only to TWRP. I didnt know why?
When i boot device to bootloader and push system Android, it starts normal to OS and work good.