Database Info

[How-To] Flash Your MT3G/Magic/Sapphire {32B} w/ CM 4.2.14.1 + Amon RA Rec v1.5.2

DISCLAIMER
Proceed at your own risk. I am not responsible for ANY outcome (good or bad) as a result of YOUR actions! Even following this guide perfectly (or any other cooked ROM guide) you could (however remote the possibility) BRICK your device. IF you choose to follow this guide READ all the way through as a "dry run" until all the steps make some sense.
GATHER YOUR SUPPLIES
Phone (fully charged)
SD card (in your phone)
Computer (w/internet access)
USB cable (one that fits your phone) OR a card reader + micro SD adapter
Download these files onto your pc:
Android 1.5 base image SAPPIMG.nbh_____________________(33d958062cc02bb2cec157f68621d2ff)
To install ALT recovery flashrec _________________________(try the latest, if it fails work backward)
Alternate Recovery img recovery-RA-sapphire-v1.5.2G.img___(md5sum - 4822fd118867bb2e66a53243a408f40e)
Android 1.6 base image DRC83_base_defanged.zip__________(md5sum - 081379e9b525484bcd1ee42bd0031a4c)
CyanogenMod Rom img CyanogenMod ROM of choice________(4.2.14.1 md5sum - c2a1e549d9296d97566e86a0a1c4bc9c)
Android ring tone pack audio-resources.zip________________(md5sum - 6cbefb897e2fb3b954d19c692d5c6966)
32A users I am researching the right files/steps to get ya'll onto CM, read this page of cyanogenmod wiki in the meantime
[*]32B UK users if my method doesn't work try this post from a user on this thread
(NOTE: If any of these links 'die' Google the file name & pm me so I can update the link)
Md5sum Values
how to check md5sum in windows : MD5summer use this program to make an md5sum file & compare values
how to check md5sum in unix/linux : in terminal type 'md5sum /path/to/file.name' [enter] & compare values
Do this once the files are on your SD card to ensure no device-to-device file transfer corruption​
BACK UP YOUR FILES
Before doing ANY mods you should ALWAYS backup your important files.
Connect phone to pc via USB
On the phone: pull down the notification bar & press ->USB Connected->Mount
On the pc: copy any & all files/folders you want to keep.
On the pc: Close the SD card folder on your pc.
On the phone: pull down the notification bar & press ->USB Connected->Un-mount/Turn off USB storage. Once this is done remove USB cable.
(NOTE: By the end of this guide EVERYTHING on your card will be GONE so don't skip this step!)
FORMAT SD CARD
From the home screen press Menu->Settings->SD card & phone storage->Un-mount SD card.
Once it is un-mounted press ->Format SD card.
Once it is formatted & has re-mounted go back to the home screen and press Menu->Settings->Applications->make sure 'Unknown sources' is checked.
(NOTE: if your phone is already ROOTED & running a Custom/Cooked ROM you can likely skip the SETUP section just check Amon_RA's thread for alternate install options)
SETUP
Find out what version of Android your phone has installed. From the home screen Press Menu->Settings->About phone-> scroll to Firmware Version.
(this is your Android Version)
If you're on Android 1.5 proceed to INSTALL section.
If you're on Android 1.6 re-connect phone to pc.
Copy the sappimg.nbh & place it on your SD card, then close everything & disconnect USB. (I am told this MUST be the only file on your SDcard or the validation will fail)
Turn off phone.
Boot into 'Fast Boot' like this: Press-&-Hold END/Power AND Pres-&-Hold Volume Down until the Fast Boot screen appears.
Press the trackball (action button) and wait for it to flash the sappimg.nbh
Once fully complete reboot phone & proceed to INSTALL section.
INSTALL
Connect phone to pc via USB
On the phone: pull down the notification bar & press ->USB Connected->Mount
On the pc: copy the FlashRec.apk & the Amon RA recovery.img onto your SD card.
If you don’t have a ‘file manager’ or ‘app manager’ go to the market & download one such as: ASTRO, LINDA, AppManager or the like. Then browse to your SD card & open/run the flashrec.apk to install it. (if asked what to open with choose Package Installer)
Open RecoveryFlash (flashrec) & make a backup of your current recovery.img. Flashrec just made "recovery-backup.img" on the root of your SDcard, so now rename Amon Ra's recovery to "recovery-backup.img" (choose replace when the dulpicate file name message appears) then open flashrec again & choose restore recovery. (Credit for this step goes to deb82swearingen Much easier then the orig method I was shone for using flashrec)
Once the flash is complete turn the phone off.
Boot into 'Recovery' like this: Press-&-Hold END/Power AND Pres-&-Hold Home. (this will be a black background with green text options)
Scroll down to ‘partition’ (press trackball to select)->partition SD->follow onscreen steps (HOME=confirm, VOL +/- changes partition size, any other key=cancel).
Once partitioning is complete press BACK to get to partition menu & scroll down to 'SD:ext2 to ext3’ press trackball to select (if you have a class 4 or 6 SD card you can then go for 'SD:ext3 to ext4' but don't try it on class2 cards it will cause system instability & likely FRY your SD card... if you don't know your class stop @ ext3).
go BACK until top says "Android system recovery" ->Connect phone to pc & scroll to 'USB-MS toggle'->HOME to confirm.
Copy the HTC 1.6 BASE & CyanogenMod ROM & Contacts.apk files onto your SD card then close the SD card folder on your PC & toggle USB-MS again, then disconnect from the pc.
Scroll to & select ‘wipe'->wipe data partition->CONFIRM
Scroll to & select ‘Flash update image->Apply sdcard:choose zip & select the HTC BASE file & let it complete (this will take a few min be patient). DO NOT REBOOT!
Scroll to & select ‘Flash update image->Apply sdcard:choose zip & select the CyanogenMod file & let it complete (this will take a few min be patient).
Once the flash is complete reboot phone (this will take up words of 5-10min+ be patient).
Once up & running on latest CyanogenMod connect to pc again & unzip the audio-resources.zip directly onto your SD card.
**************************Only Applies To CM 4.2.13**************************
Fixed Contacts.apk
Now that you have 4.2.13 installed it's time to fix the bug listed in Cyan's change-log. We will do this by replacing the broken Contacts app with the fixed Contacts.apk that you downloaded. If you get a pop-up asking about giving super user rights just hit the check mark to remember this answer & press 'yes'. This is UNIX & UNIX is unforgiving so pay attention to all punctuation, symbols, UPPER CASE & lower case. They are different & if you don't do it exactly it won't work. (UNIX assumes that you know what you want it to do so it will do whatever you tell it to, even if what you tell it to do breaks it.) So long as you are able to type what you see this is easy
Open Terminal Emulator & type these lines (hitting enter at the [E])
su [E]
mount -o rw,remount /system [E]
cp /sdcard/Contacts.apk /system/app/Contacts.apk [E]
mount -o ro,remount /system [E]
reboot [E]
(The reboot is precautionary but generally a good idea anytime you replace /system files.)
**************************************************************************
Themes/Modding
Now for those not fond of the plain Android theme you may enjoy this little app that has a growing movement backing it, read about what MetaMorph is here and then see the fast growing list of 'morphs/themes' available here.
Signatures
Now that you're a part of the modding community please For The Love Of MODDING take a moment to put the specs for your phone/ROM/theme/etc into your sig so that in the future if you have questions those of us who try to answer you don't have to play forum tag to get this basic info from you.
~psguardian

P.S. THANKS fhaines !!!!
fhaines spent days sifting through the forums to pick all these tidbits out of the masses of G1 ROM flashing posts & forwarded it to me so I could flash my MT3G, I want to say thank you to fhaines for his hard work. I just worked out the formatting & simplified the verbiage to as plain English as I could. Hope this helps those who are a bit timid to test the CM Rom waters (as I was).

Is it required to partition the sdcard, or is that just for Apps2SD & swap?

lupascu.marius: It's only if you want to use Apps2SD and swap.

Apps2sd and swap
Wysie said:
lupascu.marius: It's only if you want to use Apps2SD and swap.
Click to expand...
Click to collapse
Cyanogenmods newest roms run fastest with a swap and ext3 partition on the sd card. If you run it with just a fat32 and or ext2 you will most likely be running the rom a lot slower than was designed.
fhaines

fhaines said:
Cyanogenmods newest roms run fastest with a swap and ext3 partition on the sd card. If you run it with just a fat32 and or ext2 you will most likely be running the rom a lot slower than was designed.
fhaines
Click to expand...
Click to collapse
is it possible to just create an ext3/ext4 and swap only without using apps2sd? Or do i need a fat32 partition?
If I am not wrong the has to be rooted to apply cm? In which step of this tutorial does the phone gets root?

Nicely done!
A few days too late for me, unfortunately, but it's nice to know that I ended up with essentially the same procedure. My notes are quite a bit more disjointed than your instructions, however.
It'll be a good refresher once it's time to root my wife's phone, however.

Great Resource for noobs and advanced alike
I believe this should be stickied.

Damn you beat me to it. I have been looking for WEEKS on a sure fire way to root my MyTouch 3G. I tried the Relentless Rooter, the Gold Card method and everything else I could find to throw at this thing.
The steps outlined here are slightly different from what I did, but all in all, this is what worked for me, was nice, easy and worked great. The first time you Root a phone it takes a bit to get the process down, but it's not as hard as you think.
If this hasn't been stickied, it needs to be!

Looks good but I have a few questions.
I am currently running on CM 4.1.999 (1.6) and my phone is running very smoothly. I tried 4.1.9999 but it started to bog down and seriously slowed down. I've got quite a few apps and I've got the phone set up as I like it (including changing some of the icons with bettercut and that kind of stuff) I'm getting to the point where I'm a bit loathe to go through all that again, so my question is; what are the real world advantages I might enjoy if I "upgraded" to 4.2?

palexr said:
Looks good but I have a few questions.
I am currently running on CM 4.1.999 (1.6) and my phone is running very smoothly. I tried 4.1.9999 but it started to bog down and seriously slowed down. I've got quite a few apps and I've got the phone set up as I like it (including changing some of the icons with bettercut and that kind of stuff) I'm getting to the point where I'm a bit loathe to go through all that again, so my question is; what are the real world advantages I might enjoy if I "upgraded" to 4.2?
Click to expand...
Click to collapse
Have you tried CM updater? It can be downloaded from the market and should just upgrade your current rom.

Weemoney said:
Have you tried CM updater? It can be downloaded from the market and should just upgrade your current rom.
Click to expand...
Click to collapse
OK, thanks, I thought it had been switched off so to speak after the Google episode.
My main question remains though, are there any benefits? I know, I know, go and look at the thread in the Dream section but still, CM4.1.999 really does work very well on my Magic and I think it deserves representation here.
Allied to a good theme it is by far and away the best ROM for the Magic IMHO.

Im running it now and have no issues. It is very fast and reliable. I think its worth the upgrade.

Right You Are
smurf said:
If I am not wrong the has to be rooted to apply cm? In which step of this tutorial does the phone gets root?
Click to expand...
Click to collapse
You do need to be rooted to apply a CM ROM (or any other 'cooked ROM' I think), HERE is where you are officially Rooted as I understand the process.
psguardian said:
INSTALL
Connect phone to pc via USB
On the phone: pull down the notification bar & press ->USB Connected->Mount
On the pc: copy the FlashRec.apk & the Amon RA recovery.img onto your SD card.
If you don’t have a ‘file manager’ or ‘app manager’ go to the market & download one such as: ASTRO, LINDA, AppManager or the like. Then browse to your SD card & open/run the flashrec.apk to install it. (if asked what to open with choose Package Installer)
Open RecoveryFlash (flashrec) & press Backup Recovery Image.
Once it’s finished press in the text box & clear out the box, then put /sdcard/recovery-RA-dream-v1.2.3.img & press Flash Custom Recovery Image.
Once the flash is complete turn the phone off.
Boot into 'Recovery' like this: Press-&-Hold END/Power AND Pres-&-Hold Home. (this will be a black background with a screen full of options)
Scroll down to ‘part SD fat32+ext2+swap’ press trackball to select.
Once partitioning is complete scroll down to ‘then select convert ext2 to ext3’ press trackball to select.
Reboot phone.
Connect phone to pc after reboot & mount USB storage
Copy the HTC ADP 1.6 DRC83 & CyanogenMod 4.2.2 ROM files onto your SD card then disconnect from the pc & turn off phone.
Boot into 'Recovery', scroll to & select ‘nandroid backup’ & let it complete.
Scroll to & select ‘wipe data/factory reset’ & let it complete.
Scroll to & select ‘apply SD card: choose zip’ and select the HTC ADP file & let it complete (this will take a few min be patient).
Scroll to & select ‘apply SD card: choose zip’ and select the CyanogenMod file & let it complete (this will take a few min be patient).
Once the flash is complete reboot phone (this will take up words of 5min+ be patient).
Once up & running on latest CyanogenMod connect to pc again & unzip the audio-resources.zip onto your SD card.
Click to expand...
Click to collapse

fhaines said:
Cyanogenmods newest roms run fastest with a swap and ext3 partition on the sd card. If you run it with just a fat32 and or ext2 you will most likely be running the rom a lot slower than was designed.
fhaines
Click to expand...
Click to collapse
Quick question, I've followed the procedure posted on here step by step exactly and once I boot the phone up right after the android loading screen it goes to a black screen and sits there for a long time. Here's a thread I started asking for help with this, it has more info on my problem, thanks for anyone trying to help.
http://forum.xda-developers.com/showthread.php?t=578208

Things to check
lupascu.marius said:
Quick question, I've followed the procedure posted on here step by step exactly and once I boot the phone up right after the android loading screen it goes to a black screen and sits there for a long time. Here's a thread I started asking for help with this, it has more info on my problem, thanks for anyone trying to help.
http://forum.xda-developers.com/showthread.php?t=578208
Click to expand...
Click to collapse
Hey,
Couple of things to check and make sure of. You have to be on factory 1.5 before doing the upgrade to the Rooted HTC rom and Cyanogens rom, cannot do this from 1.6. Also, there is a wipe involved in the process, and if its skipped it may account for the FC's. Also there is a fix permission file you can run after installation and initial boot that may help with the FC's, its located in CM's thread in the Dream section where the rom is.
Fhaines

fhaines said:
Hey,
Couple of things to check and make sure of. You have to be on factory 1.5 before doing the upgrade to the Rooted HTC rom and Cyanogens rom, cannot do this from 1.6. Also, there is a wipe involved in the process, and if its skipped it may account for the FC's. Also there is a fix permission file you can run after installation and initial boot that may help with the FC's.
Fhaines
Click to expand...
Click to collapse
Yes, it is on the factory cupcake build when i start to try and install CM. The weird thing is i have had Cyanogenmod for a long time and have been doing upgrades and everything worked untill now. I upgraded to CM 4.2.1 and after that CM stopped working on my phone. I can confirm that 'other' rooted roms do work..so it seems like its just CM. Thanks

lupascu.marius said:
Yes, it is on the factory cupcake build when i start to try and install CM. The weird thing is i have had Cyanogenmod for a long time and have been doing upgrades and everything worked untill now. I upgraded to CM 4.2.1 and after that CM stopped working on my phone. I can confirm that 'other' rooted roms do work..so it seems like its just CM. Thanks
Click to expand...
Click to collapse
Quick update for anyone with any ideas. I finally got it to boot up and it runs great except for two things I've notices so far. When i try to add widgets nothing pops up and when i go to settings the window comes up for half a second then goes away and back to home screen. Now what I did to fix it was partition the sd card which i was told is NOT necessary. Then after i got it to work i tried again with a sdcard that was NOT partitioned and it did the same thing again, black screen no-go. So it seems like if you don't partition the sdcard on some phones the phone freezes at a black screen. Keywords being "some phones". So for anybody who knows how to fix the widget and settings problems not opening, please help me....Thanks

lupascu.marius said:
Quick update for anyone with any ideas. I finally got it to boot up and it runs great except for two things I've notices so far. When i try to add widgets nothing pops up and when i go to settings the window comes up for half a second then goes away and back to home screen. Now what I did to fix it was partition the sd card which i was told is NOT necessary. Then after i got it to work i tried again with a sdcard that was NOT partitioned and it did the same thing again, black screen no-go. So it seems like if you don't partition the sdcard on some phones the phone freezes at a black screen. Keywords being "some phones". So for anybody who knows how to fix the widget and settings problems not opening, please help me....Thanks
Click to expand...
Click to collapse
I don't think it has anything to do with SD partition type. Im running cm with a fat sd. everything's fine.

Nice lil issue...
Once it’s finished press in the text box & clear out the box, then put /sdcard/recovery-RA-dream-v1.2.3.img & press Flash Custom Recovery Image
I dont have this option when i try to flash the .img
it says Download Recovery Image and it is actually grayed out??

Step by Step how to install your 1st Rom

Is there a Step by Step, From A-Z guide for "dummies" on how to install a Rom? Let's assume that the phone is rooted and you have SUPERUSER & CWM installed.
A guide that includes things like; do you download the Rom to your p.c. or can you just download the Rom to your external or internal Sd card, & if so... does it matter which?
Can you use CWM to reboot your phone, or do you HAVE to use the volume/ power?
When you choose a Rom, do you start at the Original Post.. or is there a way to just download the latest version?
I'm pretty sure that there a lots of people with these questions... Some, like me that are really nervous about mucking up their phone, have read lots & lots & lots... but don't know anyone near them that could provide some hands on help... just in case..
Sent from my SGH-I727R using xda premium

1. Download ROM to PC. Copy ROM to phone sdcard.
2. Charge phone to 100%.
3. Reboot into CWM Recovery through:
a. ROM Manager app > Select Reboot into Recovery. Or,
b. Shutdown phone. Press and hold Volume + Power button.
4. Do a Nandroid backup. Using volume, scroll down to back up and restore. Press power to select. Scroll down again and select backup to internal sdcard.
5. Go back to main menu. Select Wipe data/factory reset. Select Yes. Maybe do this at least 3 times.
6. Go to advanced. Select Wipe Dalvic Cache. Select Yes. Also do 3 times.
7. Go back to main menu. Select install zip from sdcard. Select choose zip from internal sdcard. Select the ROM you wish to flash.
8. Reboot.
Some devs have extra steps so be sure to read their install instructions.
Also, read up in the Original post. It should contain the latest version and instructions for the ROM.

I download the ROM to my phone then use root explorer to move/paste it to external sd card.

Here is noob guide that will help you. Just scroll down and read I believe everything is there and after reading it you will be able to start flashing. If you think something needs to add up please post in the thread.

lyndone58 said:
1. Download ROM to PC. Copy ROM to phone sdcard.
2. Charge phone to 100%.
3. Reboot into CWM Recovery through:
a. ROM Manager app > Select Reboot into Recovery. Or,
b. Shutdown phone. Press and hold Volume + Power button.
4. Do a Nandroid backup. Using volume, scroll down to back up and restore. Press power to select. Scroll down again and select backup to internal sdcard.
5. Go back to main menu. Select Wipe data/factory reset. Select Yes. Maybe do this at least 3 times.
6. Go to advanced. Select Wipe Dalvic Cache. Select Yes. Also do 3 times.
7. Go back to main menu. Select install zip from sdcard. Select choose zip from internal sdcard. Select the ROM you wish to flash.
8. Reboot.
Some devs have extra steps so be sure to read their install instructions.
Also, read up in the Original post. It should contain the latest version and instructions for the ROM.
Click to expand...
Click to collapse
Lyndone58
Thanks, that's Excellent!!
A couple of follow up questions...
1) Do you HAVE to download the Rom to your p.c. first?
2)Which SD card do you need to copy or... depending on the answer to #1 download the Rom to?
3) Once you have wiped everything & installed the Rom with CWM, will all your apps & settings be erased?
Do you need to use Titanium to restore the apps & data?
I realize that these questions may seem ridiculous to some people... but I figure it is better to ask How before ...rather than crying for Help after.
I for one REALLY appreciate the guide... I hope that it will help some others too!
Sent From my Two Tin Cans & String Device on The Wookie Network

1) Do you HAVE to download the Rom to your p.c. first?
No you can dload it to ur phone.
2)Which SD card do you need to copy or... depending on the answer to #1 download the Rom to?
It does not matter where you put your rom. You can either put it in internal or external sd card.
3) Once you have wiped everything & installed the Rom with CWM, will all your apps & settings be erased?
Everything will be erased once you wipe data in cwm.
Do you need to use Titanium to restore the apps & data?
Yes do titanium back up of your system data+ apps before flashing anything so after flashing you can restore that. Plus do nandroid so you can have stock rom saved.
shaggyskunk said:
I realize that these questions may seem ridiculous to some people... but I figure it is better to ask How before ...rather than crying for Help after.
I for one REALLY appreciate the guide... I hope that it will help some others too!
Sent From my Two Tin Cans & String Device on The Wookie Network
Click to expand...
Click to collapse

AWESOME Guide!!!!
AWESOME Answers!!!!
AWESOME People!!!!
AWESOME xda!!!!
Sent from my SGH-I727R using xda premium

appdroid said:
Here is noob guide that will help you. Just scroll down and read I believe everything is there and after reading it you will be able to start flashing. If you think something needs to add up please post in the thread.
Click to expand...
Click to collapse
Hey appdroid, thanks but that link doesn't seem to take me anywhere... the page that it tries to open has a blank address?
Sent from my SGH-I727R using xda premium

Just go to general forum and you will see all in one noob guide thread. Its one of the sticky thread.
shaggyskunk said:
Hey appdroid, thanks but that link doesn't seem to take me anywhere... the page that it tries to open has a blank address?
Sent from my SGH-I727R using xda premium
Click to expand...
Click to collapse
Rocketing on Sky Ics¡

Update Galaxy Fit With 4.0.3 Ice-Cream Sandwich firmware [BETA 4] Realese

Prerequisites
- Charge your device to a minimum of 90% as since the procedure is bit lengthy, the phone will consume more battery than the normal usage. Lesser battery will lead to the turning Off of the device in the middle of the firmware update process.
- Back up all your data which is there in the phone memory, as in an unlikely event if the data gets lost then you can easily restore the backup.
- Up next is you need to ensure that the USB Debugging is enabled in your phone. The USB Debugging can be enabled from the path of Settings > Applications > Development > USB debugging. Apart from this you also need to ensure that your computer has ADMIN privileges and USB Read / Write Access. It’s not recommended to use computers which have limited access.
Instructions For Custom ROM users
Just in case if you are on any of the custom ROMs then you need turn Off your phone so that you can then enter into the recovery mode. The recovery mode can be entered by pressing Volume UP Key + Middle button, and holding both simultaneously press the Power Button. If the device boots normally then you need to again try to enter the same.
In the recovery mode, select the options like Wipe data/factory reset, Wipe Cache partition and then select reboot system now to reboot the phone. You can select the options using the Volume keys and can select the appropriate option by pressing the Power button. This basically clears off all the cache data which is there in the phone so that the room can be made to accommodate this all new custom ROM firmwares
Procedure For Updating
STEP 1: Official Firmware Installation
First up you need to update your phone with the 2.3.x version of firmware (And not on Froyo 2.2.x). You need to follow the instructions which are mentioned below in the form of Links. Please note that it’s a base firmware and you need to install it
STEP 2:Install ClockWorkMod 5 Recovery Image
First up you need to download the beni_cwm-5_ext4_v2.tar & odin+beni.ops.zip.Extract the files and Find Odin 4.38.exe And BENI_v1.0.ops in your Extracted Folder.
Now, Switch off Your Fit And Enter into Download Mode By Pressing Power+Menu Button+Volume Down Button Until Downloading Mode Appears.Open S5670_Odin_Multi_Downloader_v4.38.exe.Place BENI_v1.0.ops on OPS tab.Check the One Package Option.Place beni_cwm-5_ext4_v2.tar on One Package tab.Connect the device to PC which you have put in Downloading Mode.Press Start and wait for flashing process is finished.
After this you will have to proceed to the next step which is mentioned Further
STEP 3:Installation Of CM 9 ICS Firmware
1.First up you need to download Zip file which is mentioned below in your computer
https://hotfile.com/dl/151919225/1624f9b/cm_beni-beta4.zip.html
2.Now, once you are done with downloading the above file in your computer, you need to now copy the file in your phone and ensure that you are not placing these file deep into the phone. Please note that you should not modify or rename the files which you have downloaded or else there is a high probability that the file would not be supported.
3.After this Enter in Recovery Mode by Holding Power Off + Menu Button Until Recovery Mode Appears.
4.In the recovery mode, you will have to choose “choose zip from SD”. Now, from the list of files and paths you will need to first select the file which is named as “cm_beni-beta4.zip (or which You Have Copied to SD Earlier)”. Ensure that you select the file properly.
5.Now, as soon as the process is over.Select Wipe Data/Factory Reset And Wipe Cache Partition.After All Done Select “Reboot System Now”
So, there you go as soon as the phone is rebooted you will see that the firmware is updated with the latest version of Android 4.0(ICS 4.0.3)...
No Need To Say THANKS Just Press It..

mohitawasthi said:
Prerequisites
- Charge your device to a minimum of 90% as since the procedure is bit lengthy, the phone will consume more battery than the normal usage. Lesser battery will lead to the turning Off of the device in the middle of the firmware update process.
- Back up all your data which is there in the phone memory, as in an unlikely event if the data gets lost then you can easily restore the backup.
- Up next is you need to ensure that the USB Debugging is enabled in your phone. The USB Debugging can be enabled from the path of Settings > Applications > Development > USB debugging. Apart from this you also need to ensure that your computer has ADMIN privileges and USB Read / Write Access. It’s not recommended to use computers which have limited access.
Instructions For Custom ROM users
Just in case if you are on any of the custom ROMs then you need turn Off your phone so that you can then enter into the recovery mode. The recovery mode can be entered by pressing Volume UP Key + Middle button, and holding both simultaneously press the Power Button. If the device boots normally then you need to again try to enter the same.
In the recovery mode, select the options like Wipe data/factory reset, Wipe Cache partition and then select reboot system now to reboot the phone. You can select the options using the Volume keys and can select the appropriate option by pressing the Power button. This basically clears off all the cache data which is there in the phone so that the room can be made to accommodate this all new custom ROM firmwares
Procedure For Updating
STEP 1: Official Firmware Installation
First up you need to update your phone with the 2.3.x version of firmware (And not on Froyo 2.2.x). You need to follow the instructions which are mentioned below in the form of Links. Please note that it’s a base firmware and you need to install it
STEP 2:Install ClockWorkMod 5 Recovery Image
First up you need to download the beni_cwm-5_ext4_v2.tar & odin+beni.ops.zip.Extract the files and Find Odin 4.38.exe And BENI_v1.0.ops in your Extracted Folder.
Now, Switch off Your Fit And Enter into Download Mode By Pressing Power+Menu Button+Volume Down Button Until Downloading Mode Appears.Open S5670_Odin_Multi_Downloader_v4.38.exe.Place BENI_v1.0.ops on OPS tab.Check the One Package Option.Place beni_cwm-5_ext4_v2.tar on One Package tab.Connect the device to PC which you have put in Downloading Mode.Press Start and wait for flashing process is finished.
After this you will have to proceed to the next step which is mentioned Further
STEP 3:Installation Of CM 9 ICS Firmware
1.First up you need to download Zip file which is mentioned below in your computer
https://hotfile.com/dl/151919225/1624f9b/cm_beni-beta4.zip.html
2.Now, once you are done with downloading the above file in your computer, you need to now copy the file in your phone and ensure that you are not placing these file deep into the phone. Please note that you should not modify or rename the files which you have downloaded or else there is a high probability that the file would not be supported.
3.After this Enter in Recovery Mode by Holding Power Off + Menu Button Until Recovery Mode Appears.
4.In the recovery mode, you will have to choose “choose zip from SD”. Now, from the list of files and paths you will need to first select the file which is named as “cm_beni-beta4.zip (or which You Have Copied to SD Earlier)”. Ensure that you select the file properly.
5.Now, as soon as the process is over.Select Wipe Data/Factory Reset And Wipe Cache Partition.After All Done Select “Reboot System Now”
So, there you go as soon as the phone is rebooted you will see that the firmware is updated with the latest version of Android 4.0(ICS 4.0.3)...
No Need To Say THANKS Just Press It..
Click to expand...
Click to collapse
From which planet are you?

ZmisiS said:
From which planet are you?
Click to expand...
Click to collapse
Didn't Get U..

ZmisiS said:
From which planet are you?
Click to expand...
Click to collapse
Gud ques brother .. Wen beta 7 s out y s he posting beta 4 .. Seems lyk he s a new bee and want to get 10 posts through anyway
Sent From Hell ... Wanna Come .. ??

mohitawasthi said:
Didn't Get U..
Click to expand...
Click to collapse
Lol .. Wen beta 7 s out y r u posting an update for beta 4 ?? Read da forum rules .. Dnt post spam .. !!
Sent From Hell ... Wanna Come .. ??

avilove4u said:
Gud ques brother .. Wen beta 7 s out y s he posting beta 4 .. Seems lyk he s a new bee and want to get 10 posts through anyway
Sent From Hell ... Wanna Come .. ??
Click to expand...
Click to collapse
Go to hell...Dont interfere in my post..those whose want beta 4 will get it frm heree...

avilove4u said:
Gud ques brother .. Wen beta 7 s out y s he posting beta 4 .. Seems lyk he s a new bee and want to get 10 posts through anyway
Sent From Hell ... Wanna Come .. ??
Click to expand...
Click to collapse
He already has 15 posts. He coping from other websites and pasting on this site.

ZmisiS said:
He already has 15 posts. He coping from other websites and pasting on this site.
Click to expand...
Click to collapse
Ohh u knw dat fact...lolzz
Give d souce where i copy paste it...

mohitawasthi said:
Go to hell...Dont interfere in my post..those whose want beta 4 will get it frm heree...
Click to expand...
Click to collapse
This Beta 4 already is on this site.
---------- Post added at 08:26 PM ---------- Previous post was at 08:25 PM ----------
mohitawasthi said:
Ohh u knw dat fact...lolzz
Give d souce where i copy paste it...
Click to expand...
Click to collapse
Ask Aspire.

mohitawasthi said:
Go to hell...Dont interfere in my post..those whose want beta 4 will get it frm heree...
Click to expand...
Click to collapse
No one wants beta 4 wen beta 7 s out .. !!
Sent From Hell ... Wanna Come .. ??

ZmisiS said:
He already has 15 posts. He coping from other websites and pasting on this site.
Click to expand...
Click to collapse
Ohh .. Then it seems dat he loves flickering n bugs.. As beta 4 has sooo many bugs !!!!
Sent From Hell ... Wanna Come .. ??

ZmisiS said:
This Beta 4 already is on this site.
---------- Post added at 08:26 PM ---------- Previous post was at 08:25 PM ----------
Ask Aspire.
Click to expand...
Click to collapse
Why dude why i ask to Aspire U say dat i copy paste it so u knw dat fact frm where i copy paste it so jst tel wats d problm....i repeat mind ur work dont interfere...

mohitawasthi said:
Why dude why i ask to Aspire U say dat i copy paste it so u knw dat fact frm where i copy paste it so jst tel wats d problm....i repeat mind ur work dont interfere...
Click to expand...
Click to collapse
Just you work. I have a right to express their opinion.

ZmisiS said:
Just you work. I have a right to express their opinion.
Click to expand...
Click to collapse
yea so only express ur opinion or give a suggestion...dont interfere...mind ur work nly..

mohitawasthi said:
yea so only express ur opinion or give a suggestion...dont interfere...mind ur work nly..
Click to expand...
Click to collapse
My opinion is that what you are doing on this website is wrong.

[GUIDE] From stock GB to Custom JB (Noob-friendly)

STOCK GB ALL THE WAY TO JB CUSTOM ROM
If you run Gingerbread, start from A directly
If you run un-rooted Jellybean, start from B
If you run rooted Jellybean with a custom kernel, start from C.
If you run rooted Jelly Bean without a custom kernel, start from B, but skip number 1 and 6.
You might want to read this before starting, it is optional though, but will give you a better idea of what you're doing.
GUIDE
This guide shall guide you through turning your suckish GB i9070 (not i9070p) to Custom ROM JB Awesomeness.
Unless your phone shipped from Russia, it probably has Gingerbread preinstalled... so, let's first Jellybeanize it.
A) JELLYBEANIZATION:
Download Odin3 from here. http://forum.xda-developers.com/atta...1&d=1341114315. Extract it into a folder.
Download Stock JB firmware from here. http://hotfile.com/dl/222710569/1f2...m-GT-I9070-TSR-I9070XXLQE-1365486223.zip.html . Extract it into a separate folder, you will get a .tar.md5 file.
Make sure you have Kies installed, but not running.
Turn your phone off, and boot into Download mode, this can be done by holding the Vol.Down+Home+Power buttons together at the same time, till it boots.
Press Volume up to continue. Plug in your phone (make sure it's at least 60% charged) . Wait till Odin recognizes (It should say something like COMORT... to the left).
Click on PDA and choose the firmware (.tar.md5) that you extracted in step 2. Click start.
Right now, a virus which will fry your phone's internals is being installed... Calm down, joke.
When your phone boots into JB, and Odin says "PASS". Unplug.
NOTE: There is a chance that you will get a bootloop ( i.e. Android won't boot ). No, no, no... your phone isn't broken! Simply reboot to stock recovery by powering off, then pressing Vol.Up+Home+Power buttons together and wipe data/factory reset. It'll boot nicely
Now, you are currently on a stock Samsung Jellybean firmware, which is not rooted. This basically means that you do not have access to modifying the system files in your ROM, which means that you cannot install any custom kernel, custom recovery or a custom ROM... In section B, you will learn how to gain root access, install a custom kernel with a custom recovery.
B) ROOTING, KERNEL & TWRP/CWM:
Download Shaan's root from here http://d-h.st/ook
Download Temporary cwm from here http://forum.xda-developers.com/show....php?t=1987313
Download CoCore + TWRP (TWRP is one of the two recoveries available, we will use it in this guide because it looks less intimidating, and it's touch-enabled ) from here http://forum.xda-developers.com/atta...8&d=1363518705
Place all 3(or 2 if you're rooted) zip files in your external SD card
Power off. Boot into recovery by holding Vol.Up+Home+Power.
By navigating via volume buttons, choose install zip from external sd card, and install root.zip... shouldn't take long.
In the same way install update.zip. Now in a few seconds, you will get a different screen, this is Clockworkmod recovery, albeit a temporary one..
In this recovery, go to install zip, then install zip from external sd, and choose CoCore+TWRP. After installation, keep going back until the main cwm screen, and hit reboot.
NOW, Everytime you boot into recovery (which is the way to backing up and installing custom ROMs) you will get TWRP.
Now, you are rooted, with a custom kernel, and TWRP ( a custom recovery). You can either stay on stock Samsung firmware, or continue through section C, and get yourself a custom ROM.
C) INSTALLING A CUSTOM ROM:
Download any custom ROM (Recommendations at the end of the thread) zip and place it in the root of your external (or internal, but i prefer ext.) sd.
Boot into recovery.
Navigate by touch, press backup, and slide as instructed to make a backup.
Go back to the main screen and choose install. If the zip has been placed in ext. sd. then press on external sd and choose the appropriate zip and slide to install. If placed in internal sd, then choose internal sd from the top and go to /emmc folder, and choose zip and install.
When finished, navigate to the recovery home, and press reboot sytem.
Frequently Asked Questions
Q- Which of the above will increase my binary counter?
A- None! Let me clarify how the binary counter is tipped. The only way the binary counter can be increased is if you flash anything that is non-official Samsung signed, via Odin.
Q- How do I unroot?
A- You can unroot simply by following the steps in section A and not continuing with the rest of the guide.
Q- I encountered a problem, what now?
A- If the problem is related to this guide and the steps followed in this guide, then post it here, I'll try to help when possible. If you encountered a general problem not related to this guide, please post a thread in the Q&A/Troubleshooting section.
ROM Recommendations
If you want a fully stable ROM, with everything working, Cyanogenmod or Cyanogenmod based ROMs currently do not fit the cirteria, as they some bugs still remain in these. So, you may try one of the stock based ROMs.
[AOSP Themed] - JellyMod - by martin_carpio17 Link here
[S4 Themed] - Light JB - by petraru1 Link here
[AOSP Themed] - Pure Vanilla - by ikaster17 Link here
[Xperia UI Themed] Galaxperia - by Achyut Link here
However, if you'd still like to go for most change, and don't mind the small bugs, then you may try Cyanogenmod or the Cyanogenmod based ROMs below.
Cyanogenmod 10 - by diego-ch and other contributing developers Link here
MIUI v4 - by fedevd Link here
Paranoid Android Port - by nlygamz Link here
Cyanilla - by ikaster17 Link here
This is basically it for this tutorial! Finally eh? But really now, all the above is very very easy once you get used to it, I mean, all the sections in the guide, A, B and C can all be done in 5 minutes, but I've simplified everything as to suite everyone's experience.
Hopefully this guide was useful for you...

If I made any mistakes with this, please correct me

Odp: [GUIDE] From stock GB to Custom JB (Noob-friendly)
That would be very usefull
If only tons of familiar topics wasn't already created ...
tapatalked

rajman said:
That would be very usefull
If only tons of familiar topics wasn't already created ...
tapatalked
Click to expand...
Click to collapse
Excuse me for trying to contribute.

panda00 said:
Excuse me for trying to contribute.
Click to expand...
Click to collapse
You have done a good job. Remember, haters gonna hate
Sent from my GT-I9070 using xda premium

Plus, I provided this for newbies who have little to no idea about rooting and the works...

Odp: [GUIDE] From stock GB to Custom JB (Noob-friendly)
Brainiac.shri said:
You have done a good job. Remember, haters gonna hate
Sent from my GT-I9070 using xda premium
Click to expand...
Click to collapse
Yup, thanks button is to mainstream.
Hating is way more vintage
tapatalked

Added and corrected some things... Thanks R_a_z_v_a_n for the corrections.

Your welcome!

there is anyway to add brazilian portuguese language?

fromanbr said:
there is anyway to add brazilian portuguese language?
Click to expand...
Click to collapse
I don't think so... until a official JB firmware with the language is released.

Up.. since people are still asking how to root and etc.

Up

A million thanks for the guide .. I've installed Jetmod 4.0 and it's running fine. My only concern is that I created a backup of my previous ROM in the internal storage and now just 33MB space is available for installation of apps. Can you please tell me how to 1. Remove the backup, or 2. Move it to the external storage ?
Thanks !

Go to "my files" - internal (sdcard0 I suppose) select what file u want to move an move to external memory (sdcardExt).

R_a_z_v_a_n said:
Go to "my files" - internal (sdcard0 I suppose) select what file u want to move an move to external memory (sdcardExt).
Click to expand...
Click to collapse
I have already tried that, but I am not able to identify the backup. I had used to TWRP to backup and then flash JellyMod. I had looked up on some threads that the backup will be in SD -> TWRP -> Backups (or something similar to this), but there is no such folder in my phone.
:crying:

ttrublu said:
I have already tried that, but I am not able to identify the backup. I had used to TWRP to backup and then flash JellyMod. I had looked up on some threads that the backup will be in SD -> TWRP -> Backups (or something similar to this), but there is no such folder in my phone.
:crying:
Click to expand...
Click to collapse
Look for it using Root Explorer (download the app from the play store).

ttrublu said:
I have already tried that, but I am not able to identify the backup. I had used to TWRP to backup and then flash JellyMod. I had looked up on some threads that the backup will be in SD -> TWRP -> Backups (or something similar to this), but there is no such folder in my phone.
:crying:
Click to expand...
Click to collapse
in your file manager browse to ext_sd. from within ext_sd you should have a folder labeled nandroid..
also, by default, the backups should be labeled/dated accordingly..
you could also get details on each file from within file manager that will give you more specific info. date created, etc..
hope this helps..

Thanks guys, but I think I didn't make myself clear. The backup is present in the 2GB memory reserved for installing apps. How do I access that storage and remove the backup? I'm an android beginner, so pls have patience with me.

ttrublu said:
Thanks guys, but I think I didn't make myself clear. The backup is present in the 2GB memory reserved for installing apps. How do I access that storage and remove the backup? I'm an android beginner, so pls have patience with me.
Click to expand...
Click to collapse
in the "My Files" folder on your phone..
you will see All Files.. select it and youll see extSdCard and sdcard..
go to sdcard to navigate to your back up files after that move them to your memory card extsdcard..
voila.. free space..

Karbonn Smart Tab 8 version 2 Root, Recovery,etc.

Warning: This thread is for Karbonn smart tab 8 version 2
Version 2 tablets can be identified by S/N: ST*********** ver 2 at the back panel of the device
Root on Karbonn ST-8 Ver 2:
DISCLAIMER: ROOTING YOUR TABLET WILL PROBABLY VOID YOUR WARRANTY FROM THE MANUFACTURER. IF YOU DO NOT WISH TO ACCEPT FAULT FOR ANY ADVERSE EFFECTS OF ROOTING, THEN DO NOT READ ANY FURTHER. HERE BE DRAGONS.
Click to expand...
Click to collapse
Rooting
Download the utoo-root-signed.zip from here and copy it to a microSD card (do NOT extract it)
Charge up the battery in your Karbonn ST-8_version2, Power Off and remove the charger cable.
Insert the microSD card into your tablet
Get into Recovery mode( Power+volume down ) .
In the recovery you can move with the Volume down button, you can select with Power or Volume up
Select the apply update from EXT option
Select the utoo-root-signed.zip, this will install the package
Wait for the update to finish
Select reboot system now
This is a tried and tested method and has worked for everyone till now.
Attached zip credit goes to xda user @Lannig
Lag-free Tweak
Install SetCPU app
Download the file Setcpu.txt from here
Paste it into the root of your SD Card
Open SetCPU, first change the governor from "conservative" to "performance2"(This is the most important thing)
Click on options button(three dots) and then click Device Selection
Select Custom Frequencies
Now Set Min frequency to 48 MHz and Max frequency to anything according to your preference(Now you'll have the choice of setting the frequency upto 1.5 GHz)
Note:
When you wan't to conserve more battery lower the Max Frequency(while browsing or listening to music maybe) and when playing HD games up the Max Frequency(Most games will run perfectly with even 1200 MHz)
48MHz of Min frequency will give more battery in in standby mode.
Try not to Clock the CPU above 1.2 GHz for a long time as it could cause heat issues. The governor itself should speedup everything for you.
Low Internal Memory
The fact that our devices have only 1.51 GB of Internal Storage limits the capabilities of our devices. Especially with HD Games.
I recommend using GL2SD for games at the moment.
Get used to using the app, its pretty easy..
Also SEE THIS
Battery Tips
Build.prop edits
hw.nophone=true(was false)
hw.hasdata=false(was commented out and true)
ro.carrier=wifi-only(was unknown)
wifi.supplicant_scan_interval=240(was commented out)
hw.hasethernet=false(was true)[ I dont use ethernet ]
I use Greenify a lot
Also i had
1)phone.apk and odex
2)telephony.apk and odex
I removed them ( to stop displaying of cell signal usage in battery stats )
Also for ppl who want to unbrick st8-v2
Get the stock firmware package from HERE
Get the amlogic flash tool from HERE or HERE
Follow the instructions for the flash tool using the instruction manual from HERE or HERE
See the above posts and remember...........do not do things blindly........read the details completely and understand and then implement
Press Thanks if I helped U..........cheers

Stock Karbonn ST-8 Ver 2
Karbonn ST-8 v2 Stock ROM Dump And Unbricking ur bricked tablet
For a complete dump head to :
Mirror 1 [Box.com]
Mirror 2 [Mediafire.com]
For ppl who have flashed wrong TWRP in a hurry SEE THIS
also attached to this post is the Stock Recovery for Karbonn ST-8 Ver 2
Press Thanks if I helped U..........cheers

TWRP ON ST-8 V2
1. TWRP Testing for interested ppl
2. Partially tested TWRP
Link1
Link2
Press Thanks if I helped U..........cheers

Reserved...

waiting for twrp

TWRP Recvoery For smart tab 8 ver 2 Stock flashable
The attached file contains TWRP for Smart tab8 ver2.
It is initial release so it contains many bugs.
As i'm very lazy to do so myself so, if u tell me i'll resolve the bugs accordingly.
AND PLEASE NOTE I Don't have the tab so u have to check the releases yourself. My friend needs the twrp because he screwed his tablet. So i just made one for him to recover his tablet Just As is basis.

fizzy177 said:
The attached file contains TWRP for Smart tab8 ver2.
It is initial release so it contains many bugs.
As i'm very lazy to do so myself so, if u tell me i'll resolve the bugs accordingly.
AND PLEASE NOTE I Don't have the tab so u have to check the releases yourself. My friend needs the twrp because he screwed his tablet. So i just made one for him to recover his tablet Just As is basis.
Click to expand...
Click to collapse
EDIT: ur zip dosent flash in stock recovery....i got the recovery.img from zip and flashed it using flash_image binary
1. TWRP menu is visible and can be navigated
2. All buttons working
3. Reboot and settings menu fully working
4. Backup and Restore working ( tried system and data backup )
5. Mount menu ....only external sdcard can be mounted
6. Advanced menu copy log to sd working ....terminal command and file manager not working( flickering of recovery -->slide to unlock then black out)
7. Didnt try install and wipe options

need help.. please, White screen boot
I had just received my 'smart tab 8 Ver 2' two days ago and i was trying to root and install fuser-invent custom rom in it.. one thing led to another and by the time i realized the firmware of ver1 is diff than ver 2, the damage was already done.. now my tab displays a white screen and nothing else.. it wont even boot into stock recovery. can some one please help me. :crying::crying:

Root.....Check!
Thanks for the Root dude! It worked Awesome!!
Now if only we can have the Custom bugless roms the V1 users have and then it would be an icing on the cake!
I'm prepared to help out in anyway to be able to experience that goodness!! :fingers-crossed:

I am also facing the same problem , but when i connect my tablet to pc it shows "M3 CHiP" a new hard ware found . But i dont know how to fix my tablet . i knows M3 chip is amlogic processor and AML flash tool can be used to flash it ( i found it from google) . Somebody please help me to fix my tablet .

UP

unbrick
Aviast11 said:
I am also facing the same problem , but when i connect my tablet to pc it shows "M3 CHiP" a new hard ware found . But i dont know how to fix my tablet . i knows M3 chip is amlogic processor and AML flash tool can be used to flash it ( i found it from google) . Somebody please help me to fix my tablet .
Click to expand...
Click to collapse
Steps to unbrick ur tab:
Unbrick st-8-V2
1. Download the above zip extract the above zip to the root of an empty sdcard. It should look like this
2. Put the sdcard in your tablet
3. Press Power+Volume down and let it update the tablet
for furthur assistance see this link
the method i mentioned is the first one,sdcard one ....report after ur trial so that it may help others...

2012katas said:
Steps to unbrick ur tab:
1. Download the above zip extract the above zip to the root of an empty sdcard. It should look like
2. Put the sdcard in your tablet
3. Press Power+Volume down and let it update the tablet
for furthur assistance see
the method i mentioned is the first one,sdcard one ....report after ur trial so that it may help others...
Click to expand...
Click to collapse
Hi
I tried the way u mentioned , but nothing happend , still its showing white screen.
the way i did is :-
1. extract the zip and put all files inside my SD card (same as the image u showed)
2. put SD card in my tablet and pressed vol down+power (i tried with all key combinations)
3. only white screen.
also i downloaded "usb image tool" but i dont have image file to load ..
please help me to fix my tablet.

i am a newbie, I wanted to know if there is any method to upgrade Smarttab ver-2 to android 4.2.2
I want to use multiple useraccount feature in 4.2.2
I have read the forum threads and it isnt quite clear if such an upgrade is possible and tested.

recovery
the above method aborted after starting update.please guide to recover my karbon velox smat tab 8 v2 .it is always booting to recovery screen.

unbricking st8 version2
nickrulez13789 said:
I had just received my 'smart tab 8 Ver 2' two days ago and i was trying to root and install fuser-invent custom rom in it.. one thing led to another and by the time i realized the firmware of ver1 is diff than ver 2, the damage was already done.. now my tab displays a white screen and nothing else.. it wont even boot into stock recovery. can some one please help me. :crying::crying:
Click to expand...
Click to collapse
Aviast11 said:
I am also facing the same problem , but when i connect my tablet to pc it shows "M3 CHiP" a new hard ware found . But i dont know how to fix my tablet . i knows M3 chip is amlogic processor and AML flash tool can be used to flash it ( i found it from google) . Somebody please help me to fix my tablet .
Click to expand...
Click to collapse
assipposi said:
the above method aborted after starting update.please guide to recover my karbon velox smat tab 8 v2 .it is always booting to recovery screen.
Click to expand...
Click to collapse
Ok guys,This the first and last time I am posting this....
To unbrick ur tab......
1. Post what u did
2. What is wrong with the tablet according to your understanding
If you want to be helped the above two points really matter........
3. See this link
4. All info about unbricking various types of bricks can be found on the thread....
5. Also i would suggest you go through the thread fully and understand every detail
6. Another alternative for you guys would be Karbonn service center, But I feel it is useless as they take minimum 30-45 days to repair things
7. The method i mentioned is the first one,sdcard one
At this moment we have an experimental unbrick package with us thanks to developer @fuser-invent
This package is to be used in the STEP 3 of SOFT BRICK UNBRICK SDCARD method
Step 3
This only works if the first method completed far enough to allow you into the Stock Recovery or if the Alternative Methods worked and you now need to install the correct firmware.
0. Restore your SD card back to normal capacity with the SD Formatter software. This can take a long time, be patient. Choose the following options:
- FORMAT TYPE -> FULL (Overwrite)
- FORMAT SIZE ADJUSTMENT -> ON
1. Get THIS firmware package
2. Download the above zip extract the above zip to the root of an empty sdcard( less than 2gb ). It should look like this all four files should be in the root of the sdcard.
3. Just FYI, the zip folder among those four files is the stock rom ( it has boot.img,bootloder.img,system,recovery.img,aml_logo.img,logo.img )
Also this package is a recovery package for soft bricks....
4. Put the sdcard in your tablet
5. Hold down the Power and Vol - buttons to enter the Stock Recovery
6. Flash your firmware package and reboot the tablet.
7. If it worked, either plug your tablet into the computer and use USB mode or shut down your tablet and remove the SD card, then remove the "u-boot.bin" and "uImage_recovery" files from your SD card.
8. Boot back into recovery and make sure that the firmware package correctly installed the Stock Recovery on your device.
Your tablet is now back to it's original Factory Settings.
6. For furthur assistance see this link
7. If you are successful plz report back...........it will help others

2012katas said:
Ok guys,This the first and last time I am posting this....
To unbrick ur tab......
1. Post what u did
2. What is wrong with the tablet according to your understanding
If you want to be helped the above two points really matter........
At this moment we have an experimental unbrick package with us thanks to developer @fuser-invent
1. Get THIS frimware package
2. Download the above zip extract the above zip to the root of an empty sdcard( less than 2gb ). It should look like this
3. Just FYI, the zip folder among those four files is the stock rom ( it has boot.img,bootloder.img,system,recovery.img,aml_logo.img,logo.img )
Also this package is a recovery package for soft bricks....
4. Put the sdcard in your tablet
5. Press Power+Volume down and let it update the tablet
6. For furthur assistance see this link
The method i mentioned is the first one,sdcard one ....report after ur trial so that it may help others...
7. All info about unbricking various types of bricks can be found on the thread....
8. Also i would suggest you go through the thread fully and understand every detail
9. If you are successful plz report back...........it will help others
10. Another alternative for you guys would be Karbonn service center, But I feel it is useless as they take minimum 30-45 days to repair things
Click to expand...
Click to collapse
As 2012katas said, it's very important to go to the thread he links in #6. Yes, it is a HUGE thread, but it is detailed for a reason. 99% of your questions will be answered in that thread.
For example, the thread clearly says to use the ELF2 rescue image and the USB image tool to prepare your card first, then delete the ELF2 files from it and replace them with the files for your tablet. It also says that if that doesn't work you can try the SD Formatter software with my suggested settings to try and prep your card. I have no idea if the package will work until someone tries it the correct way and reports back.
On another note. If it doesn't work the first time, try to delete the u-boot.bin file only and then try again. Also mentioned in the thread, some people need to press and hold the power and vol- buttons and then when the tablet starts lighting up, start pressing the power button repeatedly, but that is rare.
As for the people with deep bricked tablets (showing the M3/M6 chip), you don't have anything to loose at this point so you best bet is to download the ST10_20121129.zip package, remove the patch.zip and update.zip, put the ST8 v2 firmware package zip I made in that folder, edit the config_progress.xml so the firmware package name is correct and no longer called update.zip, delete the part for the patch.zip, renumber the remaining steps, zip the whole thing back up and load it into the AML USB Burning software.
That might work or it might not work. You have to intelligently experiment because there is no official release for the tablet. Also you will notice that in the unbricking thread I say that if you can get the tablet showing some signs of life after the M3/M6 chip deep brick, you can then move to the SD card method. So if the usb_spl.bin and u-boot-orig.bin for the ST10 work with the ST8 to at least get the tablet out of M3/M6 mode then you could use the SD card method.
Lastly, to 2012katas, I'm rarely on XDA so if you have more questions, I see them more often on DragonDevs. You seem into this Dev stuff and smart, so feel free to get in touch to troubleshoot more.

Awesome TAB
I love this tab...
Runs Asphalt 8 flawless on 1.5ghz OC'ed.............totally awesome no lags..
btw OC'ed for battery=100% to battery=6%
tablet heats up a little on back side...........but okay for gaming........

Hi All,
I accidentally flashed TWRP recovery before routing. On Karbon Smart tab 8 Ver 2
Now, I can't do any thing...
I tried factory reset it not working.
Also failed to get into fastboot mode...
Need help to go back and flash stock recovery..

if anyone have all he junks that is pre-installed in the tab, please upload.