[Q]S-OFF and Super CID without touchscreen? - HTC Sensation

I just replaced the digitizer of my dad's phone. Unfortunatly it's not working.
Now i want to flash the file in the topic below:
http://forum.xda-developers.com/showthread.php?t=1360638
But the phone is completly stock. Can i get S-OFF and Super CID without a working touchscreen?
-Edit-
Tryed to factory reset, but phone will boot into safe mode. Prolly a waste of time replacing the digitizer...

transfer that file in sd card(just the card, not the folder), then pull the battery out, put it back, and press and hold Vol down+Power, it will send the phone into bootloader(you navigate there with volume buttons and power button), if you do everything properly it will find the file, then follow the steps.
For S-Off follow this guide
And super CID this guide but after you S-Off

OldSkool-II said:
I just replaced the digitizer of my dad's phone. Unfortunatly it's not working.
Now i want to flash the file in the topic below:
http://forum.xda-developers.com/showthread.php?t=1360638
But the phone is completly stock. Can i get S-OFF and Super CID without a working touchscreen?
-Edit-
Tryed to factory reset, but phone will boot into safe mode. Prolly a waste of time replacing the digitizer...
Click to expand...
Click to collapse
As link suggests u need S-OFF and Super CID
guide to rooting, S-OFF etc http://forum.xda-developers.com/showthread.php?t=1192300
Make sure u install an older (non touchscreen version) of recovery so you can navigate

Volume Down+Power will make my phone boot into safe mode, not the bootloader?

Related

Is there A way to turn s-on after you have s-off?

Is there a.) A way to turn s-on after you have s-off? And b) if you have to flash... Have a noob guide on doing it?
Here, read this http://forum.xda-developers.com/showthread.php?t=1192300
STEP 5 - CHANGING BACK TO S-ON - PROCEED WITH CAUTION READ BEFORE GOING TO STEP 1. YOU MUST Follow this correctly otherwise you could semi-brick your device. If you follow it correctly YOU WILL GET S-ON SUCCESSFULLY -confirmed by other users I cannot be held responsible if anything goes wrong but i will help in every situation. First time i did this with a custom ROM installed - semi-bricked my device (couldn't boot due to security warning as S-on doesn't work with custom roms), restored it using RUU.exe Second time after S-off i took the following steps and successfully went back to S-ON without any problems and booted up into stock rom.
Confirmed to work by several others as well as myself 1. Follow Step 4 above to get SuperCID - Skip if you already have it 2. Restore your official stock Rom: Just click here to download an Official Rom RESTORE STOCK EVEN IF YOU JUST RESTORED IT RECENTLY OR ARE ALREADY ON STOCK ROM. This is to ensure nothing gets changed in stock for S-on to be successful So if you are already on a stock ROM or you just went back to stock ROM, i don't care, restore the stock ROM again using the RUU.exe if you don't want to be bricked!
Connect to your phone in charging mode. click the "RUU_pyramid_*****.exe" file you downloaded and follow on screen instructions. 3. Make sure when you download the RUU. download the same or similiar RUU version as your phone came with (e.g. Tmous or EU or Asian etc). As long as you install a stock rom similiar to what you had you should be ok. FAILURE TO DO THIS MAY BRICK YOUR PHONE.
4. Switch your phone on now and let it boot for the first time and just skip through the welcome screen. 5. Go back to Step 4 - SUPERCID and go through 1 to 7 to get to the fastboot bootloader. (so just do what you did before, put adb files in local disk, adb reboot bootloader etc) 6. enter the command "fastboot oem writesecureflag 3" (Thanks Dazweeja) 7. Reboot into bootloader using "fastboot reboot-bootloader" or remove & reinsert the battery and press power on while keeping hold of volume down. 8. Bootloader should now read Pyramid PVT Ship S-ON RL. 9. Remove and reinsert the battery. Press power on as normal
You should now have S-on back and you can return your device or do whatever it is covered again under warranty.
10. IF IT DOESN'T REBOOT and bootloader says ***Security Warning** Remove and re-insert the battery and go back into bootloader and holding Volume Down +power button select fastboot 11. Run RUU_Pyramid_***.exe to reflash stock rom. (the one u just downloaded in step 1) and then reboot. It should work now
The above method works successfully. So do not under any circumstances try this without going back to stock first using Ruu.exe. and Follow the instructions correctly if you want S-on
Sent from my HTC Sensation Z710e using XDA Premium App

[Solved] Damaged bootloader. please help!

Try to unlock. Lots of things went wrong.
First the usb driver installed via installation of HTC Sync.
Open revolutionary and work on it, it stopped at "waiting for fastload".
So that I flushed a file - PG58IMG.zip, according to the noobproof post "method 2" here http://forum.xda-developers.com/showthread.php?t=1232107
It went wrong because I did not delete the file before rebooting. message: file error CRC.
While I use revolutionary to get into the bootloader again, I see this:
PYRAMID PVT SHIP S-OFF RL
Hboot - 1.17.0011
RADIO-10.11.9007.27_M3
eMMC-boot
Jun 2 2011,22:31:39
Then I can not use any key combination to enter bootloader.
If I use the revolutionary to get the the bootloader screen, it does not respond to the vol. keys and power key. Have to pull off the battery.
The phone can still boot normally.
Whay should I do to get the clockwork recovery flushed in?
Appreciated!
soma900 said:
Try to unlock. Lots of things went wrong.
First the usb driver installed via installation of HTC Sync.
Open revolutionary and work on it, it stopped at "waiting for fastload".
So that I flushed a file - PG58IMG.zip, according to the noobproof post "method 2" here http://forum.xda-developers.com/showthread.php?t=1232107
It went wrong because I did not delete the file before rebooting. message: file error CRC.
While I use revolutionary to get into the bootloader again, I see this:
PYRAMID PVT SHIP S-OFF RL
Hboot - 1.17.0011
RADIO-10.11.9007.27_M3
eMMC-boot
Jun 2 2011,22:31:39
Then I can not use any key combination to enter bootloader.
If I use the revolutionary to get the the bootloader screen, it does not respond to the vol. keys and power key. Have to pull off the battery.
The phone can still boot normally.
Whay should I do to get the clockwork recovery flushed in?
Appreciated!
Click to expand...
Click to collapse
First thing first, run RUU, then try revolutionary again, but READ THEIR HOW TO's!!!!! Again, read their HOW TO's!!!!!
If you have no RUU available you'll have to mess about with ADB, which is not that easy for a newbee.
Google on how to install ADB and stuff, once it's running and working properly, you have to type
adb reboot bootloader
fastboot flash recovery recovery_name.img
fastboot reboot-bootloader
But if your buttons still don't work, you won't be able to get into recovery.
Anyway, there are a lot of things you can do, i can sit here all night trying to write up different scenarios, but best thing for you to do is to start from scratch (RUU->REVO etc) AND READ HOW TO and don't rush when you do it.
P.S. Have you tried booting into bootloader by holding -vol button while pressing power button (after battery pull, as if you just shut it down, you might still have fast boot enabled)? Should really start from that.
tinky1 said:
P.S. Have you tried booting into bootloader by holding -vol button while pressing power button (after battery pull, as if you just shut it down, you might still have fast boot enabled)? Should really start from that.
Click to expand...
Click to collapse
Already tried many times. Either vol-down + power, or vol-up + power, the phone will start to sense. I can get into bootloader screen via revolutionary, but it does respond to menu change by holding the vol-up, or down and run by power button.
Unlocking the first time. Also new to android. used to be stick with win for years. Thanks Tinky1! I will try revolutionary again. Please stay with me.
New developemnt.
Try the revolutionary again. This time I put the cwm rocovery tools 5010 as a zip on the card beforehand. This time the Rev screen still shows "Communication with the phone interrupted unexpectedlly ......". But on the phone it now shows "Hboot - 1.17.1111". Then I unplug the USB, boot in rocovery. This time it responsed. Wait untill it says update completed, then restart phone into sense home screen.
I guess this time it is alright.
Yes. Now I can goto blue CWM recovery menu. The next figure out which rom to flush my phone. Thanks, Tinky1!
soma900 said:
Yes. Now I can goto blue CWM recovery menu. The next figure out which rom to flush my phone. Thanks, Tinky1!
Click to expand...
Click to collapse
You should change title since u found solution
Sent by my feau gee

[Q] Problems with Leedroid 2.0

Hi,
i came to the screen install form zip on sdcard
but then it starts installation
and shows : installation aborted
now i cant start the phone i always get tothis screen
with the red text this build is for ....
what can i do?
edit: now i am again there where i can install zip from sdcard, but now it doesnt recognize the sdcard. What can I do, because i the phoen does not take a microsdcard where I could put a new rom.
how can i get access to the internela storage now wihtour a os?
How did this happen ? Selecting a ROM to flash in recovery cant really cause so much damage if it fails. They usually fail because of a md5 mismatch or something.
try to mount the sd card and you can use adb to push files to it..
you could also try a full wipe..
I did several things. I rooted and unlocked the device
and now it does not boot.
Everytime I tired to flash leedroid or stock rom with choosing install form zip
installation get aborted.
I am only able to get into the boolloader and into the recovery.
how can i restore the phone?
wipe and recovery is not possible i always end in this screen
with the red text.
edit: i think i try to get into booloader and copy another file version with adb to the sd card and hope it was a download error.
but why the hell then did both the leedroid 'AND the stock rom fail?
did you flash the boot.img BEFORE flashing leedroids ROM ??
If not i suggest trying that, If that fails, Just run an RUU and start from the beginning
Thanks for the Idea,
my problem is that i cant get access to the memory wihtout a working rom
on it And now i also dont get into the recovery CWMS.
I thouzhg power+vol up would do it but it doesnt work
I think i destroyed my brand new phone.
but thanks for helping.
It's not broken.
Try Power + Vol. down. Possibly you need to retry this several times to get into the bootloader.
its not destroyed dont worry..
Run an RUU and all will be good again. Whats your CID ?
That is the problem I cannot put up software on the device
so how should i run a ruu?
Where can i get the CID from wihtout starting the phone?
I hope you have a trick how I can save the device.
angeloski said:
That is the problem I cannot put up software on the device
so how should i run a ruu?
Click to expand...
Click to collapse
You run it from your Windows desktop. Download your appropriate RUU here for example (as it takes a loooooong time).
Connect your phone to your computer via USB.
Double Click the RUU-file.
Answer the Questions and the update will start.
Remember: Your device will be reset to factory default and your data on sd card will be gone so.
Edit: You will still have to start it with power + vol. down buttons pressed (as far as I remember).
angeloski said:
That is the problem I cannot put up software on the device
so how should i run a ruu?
Where can i get the CID from wihtout starting the phone?
I hope you have a trick how I can save the device.
Click to expand...
Click to collapse
To get into the bootloader try this.
Press and hold volume down, then power. Hold both down together for 5 secs, let go of the power button then press the power button several times. This always works for me.
If this works then your phone is easy to fix.
Maybe you could try to reflash the boot.img from leedroid via fastboot.
Then flash a proper recovery.img via fastboot (I use clockworkmod)
As I heard you could then push the rom.zip via Adb the sdcard while in recovery. Last step would be install zip from sdcard.
Sent from my HTC One S using XDA
Have you installed supersu via install ZIP from sdcard? I think this needs go be installed before installing the Rom. I Don't Know it exactly. But like this it worked for me when coming from stock rom. Thats how it worked for me:
1. Unlock bootloader via HTCDev
2. flash recovery image via fastboot
3. Install SuperSU from zipfile in recovery
4. Flash boot.img from Leedroid
5. Install Leedroid from sdcard
So maybe you missed one of the steps.
Sent from my HTC One S using XDA
to get CID go into fastboot and type in cmd window ''fastboot getvar cid''
If your phone is branded, you will need that branded RUU, So i assume you will need o2 Germany RUU
Reflash recovery in fastboot, should give you access to sdcard back.
Sent from my HTC One S using xda premium
i did the same thing to my one s yesterday... followed all the steps for leedroid n got same frustration u have...
theres a nandroid file in the dev section... fastboot the boot.img and the recovery.img
ya phone WILL boot back up
ok guys ty for cheeering me up.
i wil try it with a ruu, where can i find a ruu for my htc one s.
the link in the previuos post ist offline.
i think it was 1.78.407.x when i looked the last time in my handy.
thanks
so my cid is
C:\Android\android-sdk\platform-tools>fastboot.exe getvar cid
cid: O2___102
finished. total time: 0.003s
Like i said it is a O2 i hope this helps finding the ruu
well check the Shipped ROM thread.. If its not there you can ask the OP Football if he has it or can get it..
Some RUU's cost $13 so if you know someone else who wants it, you could split the cost ?
so far, now am in the recovery flash but it is the same
count mount /sdcard
how can i put a file onto the sdcard when i have no access?
partionoing sdcard doesn't help
i was looking for this boot.img and recovery.img which was posted before
i dont find it can someone link me to it if he knows what was meant?
thanks
edit: i was desperate and tried:
fastboot oem enableqxdm 0
fastboot oem eraseconfig
but the second order was not successful
ist there another way to fix this usb brick
and to get access to /sdcard
new edit: now i write also in the help thread (noob friendly) i hope that is ok.
Did you already try this
http://forum.xda-developers.com/showthread.php?t=1667929
Or this
http://forum.xda-developers.com/showthread.php?t=1630459
Sent from my HTC One S using XDA

[Q] Stuck on Splash Screen, adb and fastboot not responding

HTC z710a
Unlocked with S-On
hboot 1-27.0000 pyramid
android 4.0.3
ROM version 3.32.666.53
Unknown Radio
rooted with superuser
I tried to install SmartDroidBerserk 2.2 for my htc sensation tonight. After following the instructions on your website http(removeThis://)smartdroidromsDOTcom/berserk.htm I ran into a huge problem; I'm stuck on the HTC splash screen.
I followed the instructions up to where it said to flash the rom. I believe that I misread this part as meaning that you could install the rom from the zip on the sd card, so I tried to do so. I got an installation error with a status 1 message during the installation. I thought that if I tried to reboot my phone that I could try to reinstall the rom or revert back to an old backup through recovery and then try to actually flash the rom the 'proper' way.
I'm now stuck on the HTC splash screen and can't do anything with my smartphone. I tried to connect it to my computer to run adb to get it back into the bootloader. When I try adb devices it doesn't even recognize that my phone is attached. The same goes for fastboot devices - no return. When I go to my computer and try and select my phone as a removable disk, windows asks me to insert a disk into the disk drive because I formatted the phone during your installation process. After I discovered that I can't use adb to get back into the bootloader, I tried to press volume down and power at the same time but I still can't get into the bootloader with that method, it just stalls on the htc splash screen, not even displaying the "quietly brillant" slogan.
If there's anything that anyone can think that would help my situation, I'd be extremely grateful! I've got a 600$ brick!!
tehwarden said:
I tried to install SmartDroidBerserk 2.2 for my htc sensation tonight. After following the instructions on your website http(removeThis://)smartdroidromsDOTcom/berserk.htm I ran into a huge problem; I'm stuck on the HTC splash screen.
I followed the instructions up to where it said to flash the rom. I believe that I misread this part as meaning that you could install the rom from the zip on the sd card, so I tried to do so. I got an installation error with a status 1 message during the installation. I thought that if I tried to reboot my phone that I could try to reinstall the rom or revert back to an old backup through recovery and then try to actually flash the rom the 'proper' way.
I'm now stuck on the HTC splash screen and can't do anything with my smartphone. I tried to connect it to my computer to run adb to get it back into the bootloader. When I try adb devices it doesn't even recognize that my phone is attached. The same goes for fastboot devices - no return. When I go to my computer and try and select my phone as a removable disk, windows asks me to insert a disk into the disk drive because I formatted the phone during your installation process. After I discovered that I can't use adb to get back into the bootloader, I tried to press volume down and power at the same time but I still can't get into the bootloader with that method, it just stalls on the htc splash screen, not even displaying the "quietly brillant" slogan.
If there's anything that anyone can think that would help my situation, I'd be extremely grateful! I've got a 600$ brick!!
Click to expand...
Click to collapse
if doesn't someone else come with other solution try to use the unbricking project
http://forum.xda-developers.com/showthread.php?p=23078349
edit: pull out your battery,put it again and then hold power button+volume down together
hold until it shows you the bootloader
tlyVisa dutch
rzr86 said:
if doesn't someone else come with other solution try to use the unbricking project
http://forum.xda-developers.com/showthread.php?p=23078349
edit: pull out your battery,put it again and then hold power button+volume down together
hold until it shows you the bootloader
Click to expand...
Click to collapse
I was able to get into the bootloader by holding down Vol + power (guess I wasn't holding it down long enough). When I get into the bootloader and try to go into recovery my phone still gets stuck on the htc splash screen for some odd reason. I was able to get it to go into recovery without a problem (until now of course). I'm not able to get into recovery to restore my backup(s).
Unlocked (with htc dev)
Pyramid PVT Ship S-On RL
HBOOT 1.27.0000
eMMC-boot
I'm reading over the unbricking project now and I'll try it tonight....this so sucks the big one (and hard).....
tehwarden said:
I was able to get into the bootloader by holding down Vol + power (guess I wasn't holding it down long enough). When I get into the bootloader and try to go into recovery my phone still gets stuck on the htc splash screen for some odd reason. I was able to get it to go into recovery without a problem (until now of course). I'm not able to get into recovery to restore my backup(s).
Unlocked (with htc dev)
Pyramid PVT Ship S-On RL
HBOOT 1.27.0000
eMMC-boot
I'm reading over the unbricking project now and I'll try it tonight....this so sucks the big one (and hard).....
Click to expand...
Click to collapse
at least you managed to enter into the bootloader.then your device it is not bricked
there is no need to use it
see then here
http://forum.xda-developers.com/showthread.php?t=1631861
about adb and fasboot commands did you open the command window in the folder where adb and fastboot files are?
rzr86 said:
at least you managed to enter into the bootloader.then your device it is not bricked
there is no need to use it
see then here
http://forum.xda-developers.com/showthread.php?t=1631861
about adb and fasboot commands did you open the command window in the folder where adb and fastboot files are?
Click to expand...
Click to collapse
yes, I put adb and fastboot in a folder C:\mini-adb and navigated to that folder. adb would print out 'attached devices are' and nothing below it when I would run adb devices. fastboot devices simply returned nothing.
I got to the second step part 9 where it asked me to fastboot reboot after flashing the recovery (which was successfully written) however when I try to reboot it just stays stuck on the htc splash screen still.
Sorry for the double post.. I just removed my battery and was able to go back into the bootloader and could get into recovery. I was able to restore a prior rooted backup but whenever I try to reboot my smartphone it loads into recovery and not into my rom.
I have the added problem of not being able to access the sd card where I would put the Android Revolution .zip file. Whenever I try to access the phone's drive windows ask me to please insert a disk into removable disk F:.
EDIT: I just used the rom in the opening post instead of using the Android Revolution rom and it installed just fine. I can use my phone again! Thanks so much rzr!
tehwarden said:
Sorry for the double post.. I just removed my battery and was able to go back into the bootloader and could get into recovery. I was able to restore a prior rooted backup but whenever I try to reboot my smartphone it loads into recovery and not into my rom.
I have the added problem of not being able to access the sd card where I would put the Android Revolution .zip file. Whenever I try to access the phone's drive windows ask me to please insert a disk into removable disk F:.
EDIT: I just used the rom in the opening post instead of using the Android Revolution rom and it installed just fine. I can use my phone again! Thanks so much rzr!
Click to expand...
Click to collapse
haha i was about to tell you now try flashing the rom to see if it will work but you already did it
happy for you man:good:
and you can always hit the thanks button if i really helped you somehow

Sensation stuck on JuopunutBear screen

Hi, at first i would say sorry for my english
So, i want install on my htc sensation custom rom, so i unlock bootloader on htcdev website, everything gone perfectly
Second step was installing CWM recovery and phone rooting, thats gone good too. Tutorial for CWM and root install i have take from this: theunlockr.com/2012/09/20/how-to-root-the-htc-sensation-on-hboot-version-1-27-0000
In next step i did wire-trick on ControlBear 0.5 beta, but phone don't want to reboot and make JuopunutBear logo, so i try to find 0.6 beta, but i can't found it. I found 0.7 beta, and on this wersion i did wire-trick, i miss a little bit with wire (wait too long) and program send me an error, i must click Enter for exit, and i clicked. From that moment my phone don't want to boot, all time i have JuopunutBear screen. I can go in bootloader, but my recovery don't want to start, so i install recovery and root again and try to restore backup from recovery, but system still don't want to boot.
At this moment i can go to bootloader and i have unlock bootloader with htcdev, recovery and probably root, i haven't s-off. My HBOOT version is 1.27.0000
Please help me, i don't know what i should do. Maybe i still can do wire-trick? I don't know :crying: I tried to find RUU, but two RUU don't want to open, and third send me info that they can't update soft and i should download correct program for update ROM memory.
Please help me!:crying:
Hi.
Run your phone's appropriate RUU, care for the region and the model as well, to be exact. For sensation XE, it has an extra LE in its name.
Sent from my HTCSensation using Tapatalk
install 4ext recovery and then enable smartflash then restore the rom backup youve got ..(step #2 and step #3 ..from this guide)
if phone still not booted then do the extra #1 step from the same above guide ...but use the boot.img from the backup you've done (will be available at /sdcard/clockworkmod/backups)
Thanks @ganeshp !!! Phone is booting and android works Thanks a lot :* You're my hero
btw, i used method with flashing my boot.img, becouse restore from 4ext didn't work
cocaine01 said:
Thanks @ganeshp !!! Phone is booting and android works Thanks a lot :* You're my hero
btw, i used method with flashing my boot.img, becouse restore from 4ext didn't work
Click to expand...
Click to collapse
Where did u go wrong? Are you s off now?
I'm not on s-off, , becouse controlbear (0.7 beta) send me an error and i must click enter for exit, after exit my sensation don't want to boot. Probably i have waiting too long for second wire "click" on sdcard, and program send error. Now i have unlock bootloader, 4ext recovery and root, i dont know which version of controlbear i need for wire-trick. If you have good version please send me a link to download
Send from my HTC Sensation
22
I got a link for 0.5beta, I'll pm you incase in case you want to try it (I haven't. Just got it yesterday, havent had a chance)
edit:used the one click tool to root, controlbear worked like a boss, took a few tries with a wire trick, phone rebooted once but no harm done
So if my phone don't want to boot system and stuck on JuopunutBear screen i can unplug my phone, plug in again and still try to do wire-trick, for that moment when phone will have s-off?
cocaine01 said:
So if my phone don't want to boot system and stuck on JuopunutBear screen i can unplug my phone, plug in again and still try to do wire-trick, for that moment when phone will have s-off?
Click to expand...
Click to collapse
you can always try the wire trick multiple times ...even when the phone is stuck at juopunutbear screen.
however if you want ..you can revert back the phone to working condition too (except sdcard) ..controlbear has this functionality too
check troubleshoot point #4 from my soff guide for further details ( link in my signature )
This is the answer for 10 points
This is what i need. Thanks a lot. I will try to do wire-trick again in future (now i know what i need to do when phone is stuck on that screen )
Thanks a lot
Edit, If i have rooted phone, i haven't use temproot.bat ?
Hi, it's me ... again..
I have done wire-trick today, but i have problem I done it, but controlbear send me text that they can't find device after wire-trick, i have unplug phone and try to restart them. I saw joupunutbear screen - again. So first what i have do i opened troubleshot and made 4. a), but phone still stuck on this screen. so i want to go to recovery, but i havent it I have try to flash recovery, but i recieved text that is unavailable or something. So i try to flash boot.img, but i can't do it too I have opened my Bootloader in sensation and i saw that i have ***LOCKED*** and under that S-OFF RL. So if i have ***LOCKED*** bootloader i can't flash anything, right? (boot.img, recovery, itp) I should unlock bootloader again or what? I'm stuck on joupunutbear logo already and have in bootloader ***LOCKED*** and S-OFF (if it's true) Please help me ... again It's possible i haven't root
cocaine01 said:
Hi, it's me ... again..
I have done wire-trick today, but i have problem I done it, but controlbear send me text that they can't find device after wire-trick, i have unplug phone and try to restart them. I saw joupunutbear screen - again. So first what i have do i opened troubleshot and made 4. a), but phone still stuck on this screen. so i want to go to recovery, but i havent it I have try to flash recovery, but i recieved text that is unavailable or something. So i try to flash boot.img, but i can't do it too I have opened my Bootloader in sensation and i saw that i have ***LOCKED*** and under that S-OFF RL. So if i have ***LOCKED*** bootloader i can't flash anything, right? (boot.img, recovery, itp) I should unlock bootloader again or what? I'm stuck on joupunutbear logo already and have in bootloader ***LOCKED*** and S-OFF (if it's true) Please help me ... again It's possible i haven't root
Click to expand...
Click to collapse
just remove the temp root with remove bat.file or whatever it is called
Ok, i have used this, but phone still is stuck on joupunut screen.
While i do wire-trick i haven't use temp-root, becouse i had unlock bootloader via htcdev, i had root and recovery - now i havent anything
cocaine01 said:
Ok, i have used this, but phone still is stuck on joupunut screen.
While i do wire-trick i haven't use temp-root, becouse i had unlock bootloader via htcdev, i had root and recovery - now i havent anything
Click to expand...
Click to collapse
check only step 2 from here(flashing a recovery)
http://forum.xda-developers.com/showthread.php?t=1631861
edit: first do this
flash jb hboot from unlimited.io site(it is unlocked patched)
http://unlimited.io/jbhboots.htm
download the one for sensation(the ics one)
then flash the recovery.img
When I type this:
sudo ./fastboot erase cache
Click to expand...
Click to collapse
into CMD, they send me text that "sudo" isn't recognizable as command or program Maybe i'm too tired...
EDIT: Okay, i'm so stupid :/ i type that without "sudo ./" and now i have hboot 1.27.1111 and i have flashed recovery 4ext. Now i can make root again and install ROM from SD card like this one: http://forum.xda-developers.com/showthread.php?t=2531054 ?
EDIT2: recovery display info that i must do full wipe and microsd card wipe. So i can't restore backup from sd now, right? I must do full wipe with sd card too and install ROM from sd card?
cocaine01 said:
When I type this:
into CMD, they send me text that "sudo" isn't recognizable as command or program Maybe i'm too tired...
EDIT: Okay, i'm so stupid :/ i type that without "sudo ./" and now i have hboot 1.27.1111 and i have flashed recovery 4ext. Now i can make root again and install ROM from SD card like this one: http://forum.xda-developers.com/showthread.php?t=2531054 ?
EDIT2: recovery display info that i must do full wipe and microsd card wipe. So i can't restore backup from sd now, right? I must do full wipe with sd card too and install ROM from sd card?
Click to expand...
Click to collapse
first: if you are willing to flash a custom rom then there is no need to root your current one
all custom roms comes pre-rooted
second: there is no need to wipe your sdcard.where did you see that?
just make a nandroid backup from recovery just in case
then format all partitions except sdcard from recovery
flash the new rom
done
Ok, i have one backup (i made it about 2 weeks ago, when sensation worked normally), so i think i haven't make second. And my recovery is now in safe-mode, so when i wipe partitions it will be normal, right?
Tomorrow i will download Vipers 5.0.0 JB and install it Thanks a lot
cocaine01 said:
Ok, i have one backup (i made it about 2 weeks ago, when sensation worked normally), so i think i haven't make second. And my recovery is now in safe-mode, so when i wipe partitions it will be normal, right?
Tomorrow i will download Vipers 5.0.0 JB and install it Thanks a lot
Click to expand...
Click to collapse
post results
by the way what do you mean by safe-mode?
rzr86 said:
post results
by the way what do you mean by safe-mode?
Click to expand...
Click to collapse
While recovery is booting, every times when i open it, it boot from 0, for second i can see something like "can't mound sd" or something.
when boot is done, recovery recieve me text:
"ATTN: recovery is in safe mode this is because the following partition is not accessible: "cache"
Please enter the wipe menu and wipe cache!
If you changed hboot you should choose to format all partitions (except sdcard)
Afterwards please reboot recovery"
And above "reboot now" i can see " ! SAFE MODE ! "
When i go in Power Menu and chose power off, i can see:
"You are currently in safe_mode.
You means that your internal partition are not accessible.
please wipe all partitions and then reboot recovery!
reboot recovery now? "
Yes or No, i can't power off device, i must take out battery.
cocaine01 said:
While recovery is booting, every times when i open it, it boot from 0, for second i can see something like "can't mound sd" or something.
when boot is done, recovery recieve me text:
"ATTN: recovery is in safe mode this is because the following partition is not accessible: "cache"
Please enter the wipe menu and wipe cache!
If you changed hboot you should choose to format all partitions (except sdcard)
Afterwards please reboot recovery"
And above "reboot now" i can see " ! SAFE MODE ! "
When i go in Power Menu and chose power off, i can see:
"You are currently in safe_mode.
You means that your internal partition are not accessible.
please wipe all partitions and then reboot recovery!
reboot recovery now? "
Yes or No, i can't power off device, i must take out battery.
Click to expand...
Click to collapse
i am seeing this for the first time
ok then wipe cache.it won't harm the device
also did you reboot recovery?
does it show you the same message?

Categories

Resources