It happened to me that the TC fell on the sidewalk face down, so I had to find and replace the screen. Couldn't find any pictorial guide so I decided to share my experience for the benefit of others with the same problem.
Cause: Cell phone shocked, fell down, hit
Symptoms: touch screen works OK, but display has cracks, blackened areas, which are spreading as time goes by.
Screen type : TC combines the matrix sensor (touch) and the LCD in 2 layers, the front touch-glass and shell, and the LCD itself underneath it.
Source of display: I bought via eBay on this source: Asia Bol
http://stores.ebay.com/newasiabol
Cost $70 inc. shipping and arrived within a week and a half. Rumors insists the at below $100 a screen is either factory dropout or refurbished.
Tools needed: Torx screwdriver T5-50, the size can be viewed after removing battery door, at lower corner.
A flat sharp tool ("fish knife") to help open the plastic case, but not too sharp to scratch the phone.
Here are the pictures and some notes:
1. Remove battery case and battery, SIM
2. Remove 2 screws from lower side
3. Prick open the shell with the flat tool
4. Prick open the top shell with the flat tool
5. CAREFUL as there are 2 tiny ribbons from the touch screen/hardware buttons into the PCB, one is held in place with sticky band (keys), the other (digitizer) is locked in-place with a lever, tiny one! - pull them out, not before noticing where they went into and lifting the lever on the smaller one.
6. Take apart the FRONT shell with the flat tool slowly as not to tear ribbons
7. Pull the LCD ribbon out
8. Carefully pull the old screen as it is held in place with sticky gum
9. Clean interior glass of phone if needed, pull out new screen protective sheet and put in place.
10. Connect new screen ribbon, 2 keyboard/jog tiny ribbons
11. Press shells in place
12. Pray you didn't forget anything and load SIM and battery
13. Good luck
more pictures...
following...(please note that where it's marked on the above picture as "jog wheel" - it is not. it's the glass digitizer ribbon.
Excelent work....!!!
Awesome man
Great contribution! You give me hope for the next generation of xda'ers!
Thank you!
Excellent work! Must be added to Polaris wiki page (if it hasn't yet!)
my lcd screen crashed 1 month ago. replaced a new screen for 450 CNY included the handwork fee.
great job.... thanks for sharing
My TC has got a big scratch on the screen (cheers to Jack, my cat who is responsible for that )...
I just ordered a new LCD screen, and by "mistake" i only ordered the digitizer...
Now after reading this post, it seems that I accidentaly did the right thing, since is only the front panel which is scratched and not the LCD itself... Am I correct?
Anyway do i have to disassemble the whole phone to get the front panel out???
As you see on the completly dismanteled TC picture above (left on the last picts row), there are:
Glass top, actually the outer top shell, and the LCD & Digitizer are one piece (the 'glassy' square with flat orange attachement)
If the scratch in on the shell glass, that's not the LCD screen, it is the so called "LCD LENS GLASS" or "faceplate".
If the TC fell and you see cracks and smears on the screen instead of what should be displayed, that's the LCD.
Please make sure where your scratches are.
Reuvenm said:
As you see on the completly dismanteled TC picture above (left on the last picts row), there are:
Glass top, actually the outer top shell, and the LCD & Digitizer are one piece (the 'glassy' square with flat orange attachement)
If the scratch in on the shell glass, that's not the LCD screen, it is the so called "LCD LENS GLASS" or "faceplate".
If the TC fell and you see cracks and smears on the screen instead of what should be displayed, that's the LCD.
Please make sure where your scratches are.
Click to expand...
Click to collapse
Thanks for the Info,you ve been very helpful .... Well my scratch is on the outside and I couldnt find any outside faceplate for my TC... Instead I ordered the digitizer (see picture attached) which for me it seemed as the right option (I did that before reading your post )... Now I will just have to wait and see when it comes, if i did the right thing........ I will let you know
well, I was (and still) confused as I was looking for some info about the screen assembly, and the only one I've found was on this lab site (not particular to TC model though).
Please read the paragraph in RED starting with "ATTENTION..." later on that page (the link above includes Google's translation from russian).
More confusing is that the part you mention here IS available as is...
puzzle solved.
I was curious so I dismantled the TC again, than I notice the the glass shell IS carrying a tiny ribbon, which means IT IS the digitizer (I though it's coming from the hardware keys).
So I assume you ordered the right part.
Reuvenm said:
puzzle solved.
I was curious so I dismantled the TC again, than I notice the the glass shell IS carrying a tiny ribbon, which means IT IS the digitizer (I though it's coming from the hardware keys).
So I assume you ordered the right part.
Click to expand...
Click to collapse
cheers... I feel ever so glad!!! ... but you would recon I would have to go through all the procedure to get it out and install the new one?
Actually it's a very delicate work with a steady hand and non scratching behaviour.
points to notice:
- The side silver bars are detached by sliding as well as pulling gently, as there are L shaped pins coming out of them into a niche in the body.
- The glass digitizer ribbon is run from one side of the main board into the other, so unlocking it (small lever and pull out) is needed as well as having the upper and rear shell apart as much as allowed, Or having the LCD wide ribbon out (& digitizer small one) and let the 2 shells free for easy access.
Saying that, it means that the procedure is almost identical as for replacing the LCD as the glass/digitizer is attached to front glass with sticky rubber and you need to get in there to release the tiny ribbon.
In your case I assume you also have to pull the bottom hardware keys' plate (assembly), in order to release it from the old shell/glass.
If that is the case, be carefull as the assembly is pinched into place by fragile plastic bumps that keep it in tight place in order to make a good push action (click). You'll have to widen the shell sides a bit and help it out.
! bent ribbon, and some mulfunction may occure.
Awesome Guide, Reuvenm you're the MAN!
I'd been searching all over for this guide so as to attempt to remove both the front and back camera. My Company just implemented this silly policy that doesn't allow phone w camera
Reuvenm, by any chance that you've had a good look at both the front and back camera and if it's a type which can be un-plug easily? Pls do not bother to disassemble the TC again, really. Just wanna check cos you may have shot some other pics of your disassembled gem that may show the front and back cameras
Anyway, great job and thanks a bunch in advance
you can disable the camera by software & registry, but I guess they want it to be out of sight..
as you see on the left pict on the first row of images, the front camera is a cubic aparatuse with 3-wings circle in the middle, just underneath the ext GPS antena hole:
this can be pulled out but I think it's ribbon (connection flat wires) is going via a cooling metal plate element and then to a PCB connector. Not sure about that as it's very delicate in there.
as for the back camera, I can't recall
here is a close up:
Hi Reuvenm, thanks for the really quick reply. Yeah i wanna get them removed altogether. So I took a leap of faith and viola! I had gotten the Back camera (3M pixel cam) out!
Followed the steps as you had illustrated and yes the 3M pixel camera was attached using some kind of L-shape flat metallic ribbon cable that ends up w a PCB connector. Wasn't difficult to remove though. I'll try to disassemble the Front camera tomorrow when i've got the time cos got to catch up on some work now.
A really big THANK YOU to Reuvenm for posting this amazing guide and i'll get some shots of the Front Cam removal and post them back here again.
Outstanding work man
You really got the guts gotta say
Elegantly done and explained!! I copied this guide with pics for future reference
This opens the door for a whole new era I guess, right guys!?
glass deformation
Hello gusy
Can you give me a suggestion ?
One day i noticed this "stain" on my screen when the device is off.
At first i thought it was liquid traped insinde the lcd (as seen on other phones) but it turned out not to be.
This stain is visible only in bright neon light (at my workplace), and it moves or dissapears almost completly when i press the screen.
Outside, or in normal light the sceen has no problem.
I think that the top glass part of the screen is to big and it bends a little causing this.
Can i remove the top layer of glass, cutt let's say a half of milimiter from the side, and stick it back on ? or is there someting holding it under ?
I noticed that in a corner i could peal it off, but i don;t want to take any chances to breack something.
thanks in advance
Does the original front cover contain the digitized too? My son scratched the front cover and I asked the service center what they would charge to change it and their quote was anywhere between 150-300 usd!!!
I don't think it does include the digitiser as I think the screen is in three parts: The casing, digitiser, and AMOLED/SLCD screen.
My guess is HTC will replace the digitiser too hence the price. I paid £130 for new casing on my phone after I dropped it after 4 days. I was not pleased and I got it back with dust under the screen, sent it back and it came back with a scratch. It's all sorted now thankfully.
I have accidently dropped my phone from 3' height and have not damaged display. Good
However, silver front case is slightly damaged; it just looks ugly; and it is very visible right by USB port.
Is it possible to replace silver front case?
Thanx
Ed
some one was able to replace their dead screen, just check for those cell phone parts resellers
another thing you can do, just put on a case
I'm trying to replace the screen on my Arrive. But I can't figure out how to get the screen out. It looks like I can pop out the back behind it, but I can't figure out how it disassembles. is there a tutorial out there or something?
To replace the *glass*, which I'm assuming is what you mean (not the LCD - they're separate in this phone, for once!)
Follow the "replace HTC 7 Pro memory card" instructions to remove the first back piece. Next, remove the screws in the next plastic back and remove it as well (it'll be easier to remove as it's just screws and contacts - no clips or wires). At this point you should see an exposed PCB, and your phone's hinge (a set of springs).
Undo the 4 screws holding the hinges on, along with the two screws holding the "pop-up" bezel (there are access holes for them - it'll make sense once you get there).
Slide the hinges across the back of the display (like you were opening the phone, but pull by the hinges! otherwise you'll break the display cable) and you'll see two screws which hold covers onto the back of the display panel. Undo the one for the bottom panel and pry the plastic bottom panel off from the back to gain access to the touchscreen connector.
Next, take a heat gun to your display and pry the glass off - I hope your glass is shattered and that's why you're replacing it because otherwise this is hugely difficult - the glass is glued on and glued on tight!
You'll see the glass is attached via flex cable thru the plastic to a connector inside the back - this is why you had to take your whole phone apart! Carefully lift the tape covering the connector, flip up the connector, and remove the old touchscreen ribbon cable and chip. Thread the new one through and reverse steps to install.
I just used the remainder of the old glue to stick my new display on, by setting it under some heavy books overnight. Your mileage will probably vary - I'm not too picky and a slightly loose/mushy screen beats a shattered one for me so I just left it at that.
Otherwise you'll probably have to figure out how to glue the display glass back on properly.
http://forum.ppcgeeks.com/htc-arrive-7-pro/144512-htc-arrive-disassembly.html
Sent from my PG41200 using XDA Premium App
Generally, I would look for one of the teardowns that have become popular for when devices are first released.....sort of the one-upping of the unboxing video.
I had trouble finding a decent disassembly - the "big" disassembly sites (ifixit etc.) seem to have ignored the Arrive and all I found on YouTube was horrid quality and mostly worthless.
That ppcgeeks thread is definitely the best resource for pics - I found that peeling the metal tape and unplugging the entire display/front piece was unnecessary by exercising some care to not break the ribbons, and I found that I needed to go a step further and remove the bottom (behind the buttons) plastic cover from the display piece to access the touch digitizer flex cable (which was behind some horribly obnoxious yellow tape).
Replace Screen under digitizer
Does anyone have a walk through on how to change the actual screen under the digitizer? I took the whole phone apart, but everything on the screen half of the phone seems to be glued.
I figured i would look around before just prying it open.
Any help is greatly appreciated.
Someone please post pics about last steps?
I was able to take hinges out of way but I am not sure if I need to peel off the metalic film. Hence I still have my top cover with glass attached with the back of the phone.
After I reach I have no idea what to do and now putting together my phone without changing broken glass!