Related
Hey guys,
Just bought the Incipio Feather case and wanted to share my thoughts in case some people were thinking about buying.
The case is definitely very light weight and pretty thin (Incipio states that it is less than 1 mm thin). It's an "ultra light, ultra strong polymer" hard case that is smooth to the touch while having a slightly rubbery feel to it. The case itself has very clean edges with no trace of any manufacturing defects. There are cutouts for the power and volume buttons, hdmi port (it's covered in the pictures on their site, but there is indeed a cutout for this), usb port, camera, microphone, headphone jack, and speakerphone. With the exception of the battery, everything is easily accessible through these cutouts.
As for protection, this is where I've been disappointed. First off, the side of the case does not rise above the side of the phone, so when you put the phone face down, the screen will be touching the surface (they provide a screen protector, but I don't think that's enough). Secondly, the case does not completely wrap around the phone, so both the top and, more importantly, the bottom of the phone are exposed. The bottom is important because on a straight drop, the pointed part of the phone will take all of the impact because it protrudes beyond the corner parts of the case. The top isn't as bad because it's flatter, so the corner portions of the case will ideally take the impact. Granted, you aren't purchasing a "feather" or "barely there" case for its protective qualities, but I think that had Incipio manufactured the case to fully wrap around the phone, both the protection and aesthetics of the case would have been enhanced.
In regards to the aesthetics, I purchased the case to avoid the bulkiness of other cases so that I could enjoy the look of the phone. However, the cutouts and the fact that the case doesn't fully wrap around the phone cause the Feather case to "break" the smooth lines of the phone. I would definitely prefer the look of a case that fully wraps around the phone.
Overall, I would not purchase this case again. At $25, even with the screen protector and microfiber cloth, I think that a case like the Androidified case that I previously reviewed provides better value with more protection. With the TPU case, my phone experienced no damage after I accidentally dropped the phone while getting out of a car. I can't say that the Feather case would provide the same sort of protection.
Thanks for the review, this was my favorite case when I had my Atrix. I noticed it on the site the day it went up but did not buy it because an employee confirmed over live chat that there was no hdmi cutout. Now that I know it is there I am placing an order now. I just bought the otterbox and I like it but its just too much for me.
This is almost the same exact case as this:
http://www.verizonwireless.com/b2c/store/accessory?action=accessoryDetails&accessoryId=47557
But yours is probably a tiny bit thinner. And this one has a pull out stand which is awesome. They tried to sell this hardcore when i bought the phone, and I got it then.
Syn Ack said:
This is almost the same exact case as this:
http://www.verizonwireless.com/b2c/store/accessory?action=accessoryDetails&accessoryId=47557
But yours is probably a tiny bit thinner. And this one has a pull out stand which is awesome. They tried to sell this hardcore when i bought the phone, and I got it then.
Click to expand...
Click to collapse
The Incipio also doesn't have those rubber ridges. I had one of these cases on my Thunderbolt and I hated it because I keep my phone in my pocket. Went with a Case-Mate Barely There case which seems to be similar to the Incipio.
It reminds me of an ultra light 1 piece Seidio innocase. It has a similar feel but its lighter and thinner.
After using this case for a few days I have to agree. This case is not worth it at all. The feather used to be my choice but incipio did not do well with this one.
I'm really hoping case-mate jumps on it and makes a barely there case for the Charge.
http://feedback.case-mate.com/forum...867323-samsung-droid-charge-barely-there-case
immaage said:
I'm really hoping case-mate jumps on it and makes a barely there case for the Charge.
http://feedback.case-mate.com/forum...867323-samsung-droid-charge-barely-there-case
Click to expand...
Click to collapse
Yeah same here. I went back to my Otterbox case but I just ordered the Trident Aegis today. I would rather have a thin light case but this feather is just plain terrible.
Why you going with Trident Aegis..instead of just using the Otterbox?
Just curious on your thoughts on the Otterbox..did you get the Trident? How is it?
The Otterbox is a good case but I am not too sold on having the buttons on the bottom covered. The Trident case shipped today and I will post pics and a review of the Aegis when it comes.
So ever since I owned my Evo 4G, I have found a kickstand an invaluable part of my daily phone use. Most phones don't come with them so I am always looking for a good kickstand case. Sadly, most of kickstand cases are not to my liking as they are either too thick, cover the sides but not the top and bottom of the phone, etc. The Seidio Surface w/kickstand for the S4 comes close but I don't like the cutouts for the buttons. It just feels awkward trying to push the buttons as I wish Seidio had covered them with TPU or silicone. My favorite non-kickstand cases are definitely the Diztronic TPU cases as they are very slim, fit perfectly, use high quality TPU, very reasonably priced, and provide good protection from everyday wear and tear. If only there was some way to add a kickstand to the Diztronic, this would be my perfect case.
So I then came across the following video where the guy added a Seidio kickstand to an Otterbox commuter and I figured I could do the same to my Diztronic case.
https://www.youtube.com/watch?v=uCb1jNmdS4s
So here is what I did:
1. Found the cheapest Seidio Surface with kickstand I could. Turns out it was a purple version made for the One X+. $8 with free Prime shipping on Amazon. Perfect.
2. I extracted the kickstand by simply pulling back the felt and popping the kickstand out.
3. Used the bottom half of the Seidio case (which now has an empty/vacant slot where the kickstand use to be) and positioned it inside the Diztronic TPU case.
4. Using a sharpie, I utilized the empty kickstand mold to trace the outline of the kickstand onto the inside of the Diztronic.
5. Used an exacto knife to cut out the outline I just traced onto the inside of the Diztronic. This left a hole/gap just the right size for the kickstand.
6. I slipped the kickstand in and secured it with black electrical tape.
7. Put my modified Diztronic case onto my S4 and done!
The kickstand is very secure and props the phone up perfectly in landscape mode. Its slim, covers all sides of the phone, has a nice lip, and buttons are easy to push. Glad to finally have my perfect kickstand case!
Wow.
Great work. I'm with you in that I love the Diztronic cases, but I would for sure mess this up haha.
Sent from my SAMSUNG-SGH-I337 using Tapatalk 2
Which provides good protection while aesthetically looking nice (not too bulky)?
Ballistic or Diztronic I am choosing between.
LcsZhDrw said:
Which provides good protection while aesthetically looking nice (not too bulky)?
Ballistic or Diztronic I am choosing between.
Click to expand...
Click to collapse
I would lean towards TPU. The Ringke Fusion cases are nice and not too bulky.
LcsZhDrw said:
Which provides good protection while aesthetically looking nice (not too bulky)?
Ballistic or Diztronic I am choosing between.
Click to expand...
Click to collapse
TPU is the way to go. Sillicon is bulky and get loose in time. They get dirty faster too.
I prefer Hard shell like Ringke Slim and Nillkin white. TPU and Silicon make the phone look cheap and they both get dirty easy
Go with the classic ebay S case for like $2.
I got it, its pretty thin, doubt you can get any thinner without risking protection.
My phone has fallen off a table twice and landed solidly on the case side on tile, just made a thud and no bounce.
Pretty sure it would of cracked if there wasn't any case.
Plus, it looks good and doesnt fuzz up like how clear ones do.
In my pinion, both are good choices.The plastic cases that scratch phones are polycarbonate. Silicone would be the choice if you want more all-around protection, but it isnt the best when it comes to drop protection if it is not a thicker case not only that but silicone provides better grip in SOME cases, it depends on the design but generally they are lacking in that section. Coated TPU cases have extremely good drop protection, as do normal TPU cases but they have the potential to chip if dropped extremely hard onto something like a driveway
I like myself a nice TPU case with a black finish!
The best case I've found for my Galaxy Light is a $3.86 TPU case off eBay. Others had more protection but made this small phone into a huge brick. No decent Otterbox Commuter-like cases. I've dropped my GL a bunch of times, and the TPU has saved it every time.
When I got my Nexus 4, I bought an Acase Superleggera Pro since it was the most Otterbox-like. It's very nice, and provides great protection. However, it's a bit thick, and since I'm constantly swapping SIMs with my other phone, the dual layer construction is a bit tedious to undo/refit each time. So I ordered a Diztronic (smoke, I wish they offered blue). It's nicely made, but I feel like it's just not quite enough protection. Maybe it's the extra heft of the Nexus 4 over the GL, or maybe it's the more solid construction vs the plastic of the Samsung. Or maybe it's because I don't care as much about what happens to my GL. The TPU just doesn't feel like it's enough protection. Plus, the previous owner of the Nexus cracked the bottom corner of the screen from a 3 foot drop with a different (but ill-fitting) TPU case. Then she really broke the screen, but that's because she threw it at a wall, so I can't fault the case for that.
I have a Ballistics case (the fat one). I am very pleased. It hasn't gotten dirty not has it gotten loose. I have dropped from about a 5 ft height onto a marble floor once. Phone did not sustain any damage. The only wear and tear it has shown is the edges looking rubbed because of the constant taking the phone in and out of my pocket. I have had it for nearly a year now. Not once complaint. Just make sure you buy a screen protector that goes all the way into the case otherwise it will slowly take it off. Hope this helps.
Definitely TPU
I'd say TPU always over silicon (unless the silicon is the inner part of a dual-protection case). I find silicon is always harder to get out of a pocket, collects dust and lint and comes off the phone too easily. TPU stays on better, feels nicer in the hand and doesn't collect dust or pocket lint
I prefer the silicon, but the Diztronic case is great (minus the "diztronic" label instead of just their logo)
Hey guys. I just decided to try Nexus 6P. Looking for some great cases to protect it! But also I don't wanna spoil the original look of it since the design's so unique and beautiful!Just got two clear cases for my former Nexus 6 from AMZ and looks wonderful, yet the clear case get darken yellowed after few weeks using, so just share your N6P case experience here and enjoy!
Long response incoming:
I initially bought a official microfibre Adopted case (in carbon) from Google along with my N6P (aluminium). I paid full price for it, but I thought it was worth the premium for an official case and the design was cool and unique. Massively underwhelmed when I received it, because it's nothing more than a generic TPU case with a thin "sticker" of microfibre on the back, which I sensed would be prone to staining and, over time, peeling. The fit was also really tight and button presses weren't that responsive. I decided in the end that the Nexus branding wasn't worth the premium, so I returned it.
I then ordered a charcoal Diztronic case. I've had good experiences with Diztronic in the past, having used their case on my Galaxy Nexus as a daily driver. It was cheaper than the Spigen Rugged Armor and I appreciated the minimalist aesthetic, not being a fan of the faux carbon fibre pattern on the Spigen. The fit and finish was great, and the buttons were clicky and responsive. My only minor niggle was the cutout for the camera sensor wasn't completely accurate, as it cut off part of the circle surrounding the sensor (100% an aesthetic oversight with no impact on function).
I then bought a Speck Candyshell Grip (in white) during the Black Friday sale, when it was 50% off. Definitely my favourite case of the three I've tested so far. It provides the most protection (being a dual-layer silicone and polycarbonate hybrid), looks striking, and, as the name implies, provides a ton of grip.
I've had a Speck Candyshell on my iPod touch and over 4 years later, it's still kept my iPod in perfect condition. The case itself is scratched up and turned a bit off-white, but I haven't exactly been gentle with it (having taken it traveling and camping) so I'm confident in its protective capabilities.
I'll likely be rocking the Speck case as my daily driver for the time being, and I'll only swap back to the Diztronic when I want a more toned-down look and slimmer profile (maybe if I'm at a fancy event wearing slacks).
Finally, I also pre-ordered a white Crash Guard + Project S from Evolutive Labs when they offered 25% off the first 50 pre-orders. IMO this would be the solution to preserving the Nexus's original design and aesthetics, while still providing a lot of protection (if the demo videos are any indication). I have no idea what Project S is, though (hopefully some kind of transparent skin, though they said it wasn't going to be made of the same material as the Rhino Shield).
I have a tempered glass screen protector from intelliARMOR protecting the front (second generation/first revision, the model prior to production of the two distinct "case-friendly" and "edge to edge" versions). It's been fine with both the Diztronic and Speck cases, though I'm curious as to whether the edge-to-edge versions might also be compatible with the Speck and Crash Guard, as there's just 1 mm between the edges of the cases and screen protector, where I find dust and grease can get trapped in between.
If you're looking for clear cases, there're Spigen's Ultra Hybrid and Neo Hybrid EX cases. The Ultra Hybrid is a single-layer case with a clear polycarbonate back framed by TPU along the edges. I wouldn't recommend it personally because I've heard that clear TPU will stain over time (as likely what happened to your original case), and the visor is completely exposed and thus prone to scratches.
The Neo Hybrid EX consists of 2 pieces: a clear TPU shell and a coloured polycarbonate bumper (essentially, the reverse of the Ultra Hybrid). It looks to be the best clear case I've seen in terms of protection (as the visor is actually covered), but I don't know how the clear TPU will fare over time, whether it will also be prone to staining. I'd wait on reviews for this case before ordering, and for it to be listed on Spigen's Amazon store, which will likely be cheaper than buying it off their main website or eBay store.
To be honest it's the first device that I don't have a case for it although I have a tampered glass and a pouch. But I'm waiting for some skins from dbrand and a wooden skin from toastmade.
Tapatalked with my Nexus 6P
I got the carbon cloth backed Nexus 6P case originally and I really like the look and feel of it, but it's not the most protective. The only issue I've had with it is taking screenshots (the case presses buttons you don't mean to) and it wouldn't work with a tempered glass screen protector (it peels it up).
On the black Friday I got the Speck CandyShell in black/slate and I'm digging it. It's more protective and it makes the button presses a little harder, which I like. I would think it'd work with a glass screen protector as the bezels don't intrude onto the glass very much.
I use a Supcase Unicorn Beetle Hybrid as my standard case. I usually slide it in my pants or jacket pocket. I do wish there was a belt clip for the Beetle Hybrid, but to get a belt clip case combo you typically are into something much thicker and substantial that is, for me, unnecessary. When I'm wearing a suit, I use it bare and carry it in a Story Leather belt clip holster made for the iPhone 6s Plus. The phone has a Skinomi Tech Glass protector on it.
My experience mirrors LuckyDragan a little bit.
My first case was the microfiber case from the Google store. While it looked nice and the in hand feel was decent, I felt it cost way too much for what it was. I ended up returning it because when I pressed the edge of the case by the buttons it would change the volume. Not cool for a $35 case.
Next case is the reg. Adopted case. It's not bad. I really like the textured sides. It's also fairly narrow. Thing is, I paid $10 for it, at the reg. price of $20, I'm not sure if it's worth it. By the pics I've seen, I think it looks better than the Diztronic, especially the fingerprint cut out.
3rd case is the Spigen Rugged Armor. Except for the camera cut out (I don't like how it doesn't leave room for the blueish oval), I think it looks the best of all the cases I've tried so far. My nags are that It's all little wide and slippery. At $13.00?, it's a good buy.
4th case is the Speck Grip. My favorite so far. It's not as thin as the other cases but not bulky. The grip is awesome, no problem using the phone with one hand. At first glance, I didn't think it was the best looking case, but it's starting to grow on me. The protection and how it makes the phone so much easier to handle makes it a winner. @ $20 I paid during the Google store's sale, I think it's worth it. @ the reg. price of $40, idk.
If haven't yet, check out Pilz review thread, so much good info.
White Speck case as my daily driver.
I have tried the Diztronic one, while it does provide protection, did not like how loose the edges felt, definitely not as snug and stiff as my Diztronic Ultra that is on my GS6. It easily bent out edges for my taste, and thought of getting some debris that could scratch up the phone was bugging me somewhat. If you need a very minimalist, fingerprint resistant, and decent lip for screen protection, that is the case to have.
Also have the Supcase Unicorn Hybrid Ultra. great case, snug and firmer edges than the Diztronic one, but damn, is that case slippery. I have a habit of placing the phone on my car seat, and that thing just slides around like a hockey puck on ice when placed on its back. Placing it face down did help... still preferred it over the Diztronic.
But snagged the White Speck Candy Shell Grip case at 50% off, love it. Excellent grip, very tight and solid felling edges, does not slide when placed on a my car seat. Wished they offered a matt finish white version of this, since I am not a fan of shiny cases, but the black rubber lines offset it enough to be likable for me. Sporting the Orzly TGSP,with that case there is a minimal space between the glass and the edges of the case, nearly perfect sealed fit. Hoping the intelliglass ones are a bit more of an coverage so that it could have a near gapless glass to case seal, still waiting on receiving mine...
Currently have the Tudia case which is brill, but also got the Spigen rugged case coming.
Official microfiber case in carbon. No screenshot issues or button issues in general. I love the soft fabric feel. Feels more "welcoming" than the cold, hard plastic/TPU of other cases I've used. Regarding durability, I'm a little concerned, but only time will tell how the microfiber will hold up.
Smoked Ringke fusion is my case of choice, at least for now. I also have the Orzly flexicase and Spigen rugged armor. Don't really care for either of those.
Anyone want to trade a case for the spigen rugged armor? mint condition and hasn't been used other than trying it on once.
PuffinNugz said:
Smoked Ringke fusion is my case of choice, at least for now.
Click to expand...
Click to collapse
I'm also using this case and think it's a good balance of fitting, protection, minimal bulk, etc all for a low price. I bought it off Amazon for $11 but unfortunately it's been outta stock for the past month or so. I wished they had a clear case instead of smoke coloring though.
I use spigen rugged armor, it's a good case that offers high protection to your phone..
i intend to order the verus high pro shield case though, just want to wait for some time until they fully supply the updated case.. the first batches had a defect about the charging port..
InfestedAdam said:
I'm also using this case and think it's a good balance of fitting, protection, minimal bulk, etc all for a low price. I bought it off Amazon for $11 but unfortunately it's been outta stock for the past month or so. I wished they had a clear case instead of smoke coloring though.
Click to expand...
Click to collapse
They've got both clear and smoked in stock through ebay. http://www.ebay.com/itm/Ringke-FUSI...hash=item3d076ed1ad:m:mNMnxjoDe6mqlXAgy0u2D6g
PuffinNugz said:
They've got both clear and smoked in stock through ebay. http://www.ebay.com/itm/Ringke-FUSI...hash=item3d076ed1ad:m:mNMnxjoDe6mqlXAgy0u2D6g
Click to expand...
Click to collapse
Thank you for the notice. Strange. Is Ringke the actual seller? I wonder why they stopped selling via Amazon.
InfestedAdam said:
Thank you for the notice. Strange. Is Ringke the actual seller? I wonder why they stopped selling via Amazon.
Click to expand...
Click to collapse
Yeah, not sure about amazon, but I bought mine from that ebay link. Pretty sure they are the actual sellers.
The Spigen rugged arrived today and it is SOOOO much nicer than the Tudia one. Better fit and feels nicer and more secure.
Sent from my Nexus 6P using Tapatalk
I've had a few cases so far.
SR Tech - Typical TPU case. Decent protection. Cutouts were slightly off. Total fingerprint/oil magnet. Got real slippery after a week or so of use and required a wipe down. Did not interfere with my Pleson TGSP.
Spigen Rugged Armor - Soft touch finish felt really good in hand. Very good protection at the sacrifice of some added bulk. Cutouts were precise and buttons had a nice tactile feel. Soft touch got some smudges on it occasionally but not nearly as bad as the SR case. Did not interfere with my Pleson TGSP but it was really close.
Spigen Thin Fit - Very interesting finish on this case. Kinda felt like the back of the Nexus 6. Fingerprints weren't really a problem but oil/smudging was. Case snapped on snugly and provided good protection for the covered areas. Top and bottom of the phone were exposed. Did not interfere with my Pleson TGSP.
Nillkin Nature - This is my daily driver. Pretty much the same as the SR Tech, only about half the thickness. Cutouts are more precise and there is a cover for the Type C port, which I really like. This is literally the thinnest case I've ever used and it really helps make the already large 6P more manageable in the hand. I wish it came in a matte finish so oil/fingerprints weren't so much of an issue, but other than that I'm happy.
Adopted for now until bumpers start arriving and be reviewed.
Ringke smoke and Google Microfiber. Like both and switch weekely
Sent from my Nexus 6P using Tapatalk
I switch from the official google carbon case and spigen ultra hybrid. They are great cases but the buttons on both aren't the best. I also have speck case but I use it for when I go to the gym. Diztronic case is nice but phone feels loose inside and verus case.. Its whatever.
Sent from my Nexus 6 using Tapatalk
One of my favorite things about my Sony Xperia Z3 over the last couple of years has been the Case-Mate Tough Case I've had on it. I drop my phone pretty regularly, and that thing holds up to whatever I throw at it (or, I guess, whatever I throw it at). In addition to being a nice protective dual-layer case, it's also really grippy with a nice texture - I've never had a phone that felt so secure in the hand.
I've been looking for a similar case for the Moto X Pure, but I can't seem to find one; most of the cases I've seen that have a decent protective frame around the edges take themselves out of the running for me with a smooth back (often for the sake of transparency, to show off the custom phone), and the one case I found with a nice texture was a Nillkin skin that doesn't protect the sides and has no lip to raise the screen off a desk.
Anyone have any recommendations for a good case that's durable and protects against drops, and also helps make this giant of a phone feel a little more secure in the hand? (I have been looking at the Incipio Dualpro but haven't gotten a chance to see one in person yet so have no idea what the texture is like.)
I actually like the otterbox defender as it has excellent grip. But it is bulky so it may not be on par with what you are looking for. I like the bulk though as it is perfect for my hand size and maintaining firm control of my phone. The silicone has a textured/ribbed back that is nice.
Sent from my XT1575 using XDA-Developers mobile app
I have the Supcase Beetle -
http://www.amazon.com/SUPCASE-Unicorn-Premium-Protective-Motorola/dp/B0154AQ3QK/
Very good protection, frosted back so you can see the colour/design of your phone. Thick rubber around the sides for grip and protection. The two raised ridges on the back reduce the side to side rocking a bit, which is an issue on our curved backs. Not too expensive. I would recommend considering it.
I have the same problem. I bought the Diztronic Case as well as the Incipio octane.
The octane is surprisingly good looking. It has a frosted back but somehow.. it feels kinda grippy. I can't explain it. It's hard plastic.. but it is gripper than the naked rubber back. It's weird.
The octane is also grippier around the edges (softer TPU) than the diztronic. It's also a little thicker. (enough to be noticeable). BUT the buttons are hard to press (I think I might can fix that but I have yet to work up the nerve to take a razor to my $20 case). The biggest problem here is that the headphone cutout isn't big enough for my ATH-M50s or my AUX cord.... so... yeah. Another thing that could possibly be fixed once I figure out the best way to go about it.
Now, for the Diztronic: This is seriously the best built case I've ever seen for a phone. It fits perfectly. It barely adds any bulk to the phone. I can't speak for the MXP (haven't dropped it yet) but I have carried three phones in diztronic cases and nothing has happened to any of them. There's an attention to detail with Diztronic that you don't get with a lot of other cases. The button cutouts for this case are unlike any case I've ever seen. It's still easy to press the buttons and the buttons stick out from the case the same length that the actual buttons stick out from the phone. It feels like you're pressing the actual buttons. You'll have no problem fitting any headphone cord into this case. The ONLY thing I don't like about this case is that it actually does not add a lot of grip, but overall, its my favorite. I highly recommend it.
Edit: I don't have it but the Incipio dualpro is probably good. It'll add more bulk though.
I'm a fan of the SUPCASE Unicorn Beetle Pro with the holster clip and built-in screen protector. It has held up very well against abuse and saved my MXPE a number of times. Of course you don't need to use the holster, but it does help to protect the screen, especially in a gym bag or whatever. Here is the link: http://www.amazon.com/SUPCASE-Holster-Motorola-Protective-Protector/dp/B0153T7TSI
I have had mine in a Supcase unicorn beetle (with the frosted back) since september 30th, dropped numerous times, easy to put in pocket.
If I needed a holster I'd go with the Supcase heavy duty.
Supcase Unicorn Beetle is perfect
I like the SUPCASE beetle, but like there dustproof/"water resistant " version with interchangeable back plates better
Sent from my XT1575 using XDA-Developers mobile app
I highly recommend the Case Mate Tough Frame bumper for the MXPE. Perfect fit. Ridged power button on the bumper.
Part 2 of 2
I definitely agree about with you about the Diztronic case. The buttons are actually easier to use with the case on than without it. As far as the grip goes, at first I noticed it being a little slippery. However, I have gotten used to it.
elite001mm said:
I have the same problem. I bought the Diztronic Case as well as the Incipio octane.
The octane is surprisingly good looking. It has a frosted back but somehow.. it feels kinda grippy. I can't explain it. It's hard plastic.. but it is gripper than the naked rubber back. It's weird.
The octane is also grippier around the edges (softer TPU) than the diztronic. It's also a little thicker. (enough to be noticeable). BUT the buttons are hard to press (I think I might can fix that but I have yet to work up the nerve to take a razor to my $20 case). The biggest problem here is that the headphone cutout isn't big enough for my ATH-M50s or my AUX cord.... so... yeah. Another thing that could possibly be fixed once I figure out the best way to go about it.
Now, for the Diztronic: This is seriously the best built case I've ever seen for a phone. It fits perfectly. It barely adds any bulk to the phone. I can't speak for the MXP (haven't dropped it yet) but I have carried three phones in diztronic cases and nothing has happened to any of them. There's an attention to detail with Diztronic that you don't get with a lot of other cases. The button cutouts for this case are unlike any case I've ever seen. It's still easy to press the buttons and the buttons stick out from the case the same length that the actual buttons stick out from the phone. It feels like you're pressing the actual buttons. You'll have no problem fitting any headphone cord into this case. The ONLY thing I don't like about this case is that it actually does not add a lot of grip, but overall, its my favorite. I highly recommend it.
Edit: I don't have it but the Incipio dualpro is probably good. It'll add more bulk though.
Click to expand...
Click to collapse
bill875 said:
I'm a fan of the SUPCASE Unicorn Beetle Pro with the holster clip and built-in screen protector. It has held up very well against abuse and saved my MXPE a number of times. Of course you don't need to use the holster, but it does help to protect the screen, especially in a gym bag or whatever. Here is the link: http://www.amazon.com/SUPCASE-Holster-Motorola-Protective-Protector/dp/B0153T7TSI
Click to expand...
Click to collapse
One of the best fa sure... Looking for a replacement.. Any other similar quality cases out there?