Hello! I just bought a new bluetooth keyboard from Logitech and so far is working perfectly. But I have a couple of adaptors (one to USB port and another one to multiple plugs...) but I don't know why, they seem to work, but every 2 seconds they stop being recognized and then they connect again.
My main goal would be to plug in a usb mouse...but with that issue is impossible to work with it. Anyone had some similar problem? Any ideia on how to solve it?
I tried to find anyone else with the same problem...but nothing..
Related
My Sensation is could not be recognized by a computer, even in hboot, i tried a few computers, none of them worked. But then when I try plugging it through a usb hub, it magically worked! albeit it works quite slow as it complains about not being USB 2.0, etc. Now this is really work, the phone can only be recognized when plugged via a hub, anyone knows what might be causing this?
PS, I tried another cable, both worked on my DHD perfectly but same problem with Sensation.
EDIT: I tried a usb 2.0 hub and it doesnt work, i think my phone's usb 2.0 is messed up.
Anyone knows of a firmware i should try flashing that would probably fix this?
it seems like even it gets connected to usb 1.0 hub, large file trasnfer(eg: a new rom) would still still halt halfway.
Tried a third cable and I am now starting to wonder if it is hardware related, i would off order a usb connector module off ebay, or send it to get fixed, but i wanna make sure it isnt software related...
btw, anyone knows how much technical skill would i need to replace the module? if it doesnt require soldering i am pretty confident to do it, i mean i had replaced the earpiece on my dhd before, now that was easy!
You have to pick the option to connect sdcard. If sense then drop down menu and pick disk drive if cm7 then turn on USB
Try to install HTC sync as well
good day to everyone. firstly, i would like to thank you for having the time to read my post.
well basically heres my inquiry, my unit is the alcatel tab t10. i never had any problems with it until recently, my device's usb port suddenly stops working.
tried unchecking the usb debug mode, tried checking it but to no avail, the usb still does not work. it doesnt seem to connect to my laptop. tried changing the cable.
i also tried connecting my device to my brothers laptop.
correct me if im wrong, but when the usb fails to connect to any laptop, their should be a notification in the laptop that the device is not recognized. but in my condition, no notification shows up. its like my device does not really connect at all.
oh and if it helps, i bought an otg cable before it started malfunctioning. but the only thing i had conneceted to my device is a wired mouse and a wired generic gamepad, which both seems to be working perfectly fine.
also, if i connect my device to a wired mouse, it would work perfecly fine. i could also connect to a usb flash drive, that is via the otg cable.
so whats weird is that the usb cable does not work, but the otg cable works fine.
if you have any question or any suggestion , i would truly appreciate it.
Hmm.....well the good thing is the port itself isn't "dead" as you can still utilize it for OTG. My only suggestion is make a backup of all your apps and data and try a factory reset.
Sent from my SCH-R880 using xda app-developers app
thank you for the suggestion guitarman2010. unfortunately my usb port isnt still working. i also reflashed my device's current firware. but still wasnt the solution i was looking for. i was just wondering if there is a directory under the root folder that holds the devices usb driver? would it be possible that the device's driver itself got deleted? i wam still at awe that the otg cable still works like a charm.
and another thing, is the male usb pin the same with the flash drive's pin? cause if i connect the usb cable to the otg cable it wont work, but the flash drive works normally.
sorry for the amount of question im posting
thank you very much for the suggestion. especially when u told me that the port itself wsnt dead. i can now breathe easier..
and future suggestion and advice would be appreciated.
do you guys know how to access the phoneutil in tablet? maybe i should change the usb option to pda? but i heard that its only applicable to samsung 4.0.3 devices? suggestions are appreciated.
Several people have mentioned that they have host mode connectivity problems. USB devices that are connected to the tablet, via an OTG cable or a USB host adapter, are not (or not always) seen by the tablet.
Some people mentioned that the problem started only after the upgrade to 4.1.2.
In my particular case -- stock rom but rooted -- it works immedeately after reboot but stops working sometime later, a strong clue that it is a software (driver) problem.
This has been going on for a while now. I'm wondering: what is the current status? Did anyone complain to Samsung and got a useful answer? Did anyone send the tablet back as defective?
When connected to computer touch screen doesn't work properly.. Does anyone else experience this issue? I've tried changing wires still same result..
Hello XDA-developers,
I bought a new tablet a few days ago and have a slight problem regarding the Mac Address. It keeps changing after turning on wifi every time.
I found mutliple answers to similar problems but they didn't work for this specific tablet.
Now, I need to know if there is a way to change it to a static Mac Address, it uses Lollipop 5.1 and I rooted it using KingoRoot for Windows.
I just made some search for myself and found a file called "setmacaddr" (without extension). I don't know if it's just a thing every tablet has or if it is the problem.
If you need more information about the tablet, don't hesitate asking me!
Sincerely,
Marvin
EDIT:
I rooted this tablet because it had the problem when it was not rooted. I needed to root it for the methods I tried till now. (Like I said, they didn't work)
Hello, it's me again,
does anybody have a clue at least what I can try to do?
Would help me very much!
Solution:
I solved the problem in a slighty different way.
I know this is not the best way but maybe someone just needs a similar solution!
I bought a USB 2.0 -OTG ethernet adapter² and connected it with the switch next to my pc, which is connected to the router. Thus, you are able to have stable internet connection without minding your MAC-Address in most of the time (like 99,9%). Of course, your tablet only gets internet while plugged into it, so you may only do this if your tablet remains in nearly the same place or if you are able to quickly wire it different.
² can't post the link to the product because I'm a new user. Any USB-2.0 OTG ethernet adapter should work, it just needs a micro usb otg plug.