Database Info

[Q] Samsung P6200 Stuck on boot

Hi guys,
i've a samsung p6200 and i was running on ics 4.0.4 austria, then i've tried to move to P6200/P6210/T869 CyanogenMod 10 using cwm recovery.
so, since then i couldn't install any other rom without bootlooping.
I tried putting back ICS (previous version) using odin like i did before, it completes without errors but i get stuck on galaxy logo.
I tried several ways of flashing through cwm and heimdall, all go through but end up with the same results :S
Can i get some help? I'm kinda lost here and don't know what to try next.
Thanks in advance.

xzard said:
Hi guys,
i've a samsung p6200 and i was running on ics 4.0.4 austria, then i've tried to move to P6200/P6210/T869 CyanogenMod 10 using cwm recovery.
so, since then i couldn't install any other rom without bootlooping.
I tried putting back ICS (previous version) using odin like i did before, it completes without errors but i get stuck on galaxy logo.
I tried several ways of flashing through cwm and heimdall, all go through but end up with the same results :S
Can i get some help? I'm kinda lost here and don't know what to try next.
Thanks in advance.
Click to expand...
Click to collapse
Reinstall cwm, wipe data, install cm9/10, wipe data again, reboot. Don't wipe data using stock recovery, only cwm
Sent from my myTouch 4g via Tapatalk

ringnutz said:
Reinstall cwm, wipe data, install cm9/10, wipe data again, reboot. Don't wipe data using stock recovery, only cwm
Sent from my myTouch 4g via Tapatalk
Click to expand...
Click to collapse
i reinstalled cwm , wiped data :
-- wiping data...
formatting /data...
error mounting /data!
skipping format...
formatting /cache...
formatting /sd-ext...
formatting /sdcard/.android_secure...
error mounting /sdcard/.android_secure...!
skipping format...
data wipe complete.
then when i go to choose zip from sd card it gives me " E:Can't mount /sdcard
or if i try choose from internal sdcard : "E:Can't mount /emmc/
Can u please help me ...
thank you in advance

xzard said:
i reinstalled cwm , wiped data :
-- wiping data...
formatting /data...
error mounting /data!
skipping format...
formatting /cache...
formatting /sd-ext...
formatting /sdcard/.android_secure...
error mounting /sdcard/.android_secure...!
skipping format...
data wipe complete.
then when i go to choose zip from sd card it gives me " E:Can't mount /sdcard
or if i try choose from internal sdcard : "E:Can't mount /emmc/
Can u please help me ...
thank you in advance
Click to expand...
Click to collapse
Your EMMC is gone, tipical hard brick ! look at releated thread ....
It's possible you have executed a "Factory reset" from ICS recovery before ?

losteagle said:
Your EMMC is gone, tipical hard brick ! look at releated thread ....
It's possible you have executed a "Factory reset" from ICS recovery before ?
Click to expand...
Click to collapse
i tryed so many options thant i don't remember i've executed that from ICS...
but now the only thing i can access on my TAb is the dowload mode cause if i try recovery gives the mensage " firmware upgrade encountered an issue"
and if i try to flash ICS again with odin it hangs on move to FACTORYFS.IMG and appears the fail menssage on odin.
any kind of help pleasee!???
thanks in advance

xzard said:
i tryed so many options thant i don't remember i've executed that from ICS...
but now the only thing i can access on my TAb is the dowload mode cause if i try recovery gives the mensage " firmware upgrade encountered an issue"
and if i try to flash ICS again with odin it hangs on move to FACTORYFS.IMG and appears the fail menssage on odin.
any kind of help pleasee!???
thanks in advance
Click to expand...
Click to collapse
Right now i've downloaded samfirmware pit file and tryed to flash ICS with that pit file selected and repartition too...
i've succeed to finishing the installation and now i can access to stock recovery. but when i try to turn tab on it hangs on galaxy tab logo !
any idea?
thanks in advance

Have a look at this thread, should work for our device as well
http://forum.xda-developers.com/showthread.php?t=1667886
from my myTouch 4g via Tapatalk

Hi,
After a weekend lost searching for a fix to my problem I've decided to take the Tab to repair at the dealer. my tab has an insurance and i will activate it.
for a small resume, i've scanned for partition errors, having received I/O error on mmcblk9 / 10 / 11.
i tried re-partition without success
at last i 've flashed my tab with pit file modified for devices who have bad sector issues and i nearly succeeded, because get an ICS boot but gave me a message that need to do a data wipe because of some encryption. when i made the wipe with the CWM recovery i get mount /data and /sdcard error...
so once that i have insurance i'll use it .
the bad news is that it can take up to ninety days, i'll prai that does not happen and take much less time.
tks

[Q] HELP!! GT-i9100M STUCK IN SAMSUNG SCREEN

Hello!! This is my first post and I was hoping someone will help me. I have a GT-i9100M locked to bell that wont boot. It gets stuck on the SAMSUNG splash screen. I am able to boot into recovery and download mode. But every time i boot into recovery mode i get the following error
#MANUAL MODE #
--Applying Multi-CSC...
E: failed to mount /system (invalid Argument)
can't mount '/system' (invalid Argument)
E: failed to mount /system (Invalid argument)
Im assuming my /system partition got corrupted. After doing lots of research, I have have tried to wipe data/factory reset, wipe cache partition, and re-install the firmware through Odin but didnt have any luck. One thing i should mention, is that Odin doesnt show me that my device is connected. Should i attempt to reinstall a new ROM with a bootloader? Im completely lost. If anyone got any idea what i could do to revive my phone. Ill greatly appreciated.

bmesta said:
Hello!! This is my first post and I was hoping someone will help me. I have a GT-i9100M locked to bell that wont boot. It gets stuck on the SAMSUNG splash screen. I am able to boot into recovery and download mode. But every time i boot into recovery mode i get the following error
#MANUAL MODE #
--Applying Multi-CSC...
E: failed to mount /system (invalid Argument)
can't mount '/system' (invalid Argument)
E: failed to mount /system (Invalid argument)
Im assuming my /system partition got corrupted. After doing lots of research, I have have tried to wipe data/factory reset, wipe cache partition, and re-install the firmware through Odin but didnt have any luck. One thing i should mention, is that Odin doesnt show me that my device is connected. Should i attempt to reinstall a new ROM with a bootloader? Im completely lost. If anyone got any idea what i could do to revive my phone. Ill greatly appreciated.
Click to expand...
Click to collapse
can anyone help me or suggest something? Ill appreciate it a lot

Hey man the screebshot shows that u dont have cwm
Flash it via odin first
Then try
sent by typing by my fingers

[email protected] said:
Hey man the screebshot shows that u dont have cwm
Flash it via odin first
Then try
sent by typing by my fingers
Click to expand...
Click to collapse
hey amit!! thanks for your quick response man. I dont have CWM install i only got the bell stock recovery. Will I be able to install CWM if odin is not recognizing my phone? I have attempted to falsh the stock firmware through odin but no luck. im thinking of flashing the stock firmware through a SD card. i dunno if thats a good idea.

First u have to install cwm via odin
Install ur phone drivers via kies
Then install a custom rom
sent by typing by my fingers

E:failed to mount /efs (invalid argument)

Having some phone issues - Samsung Galaxy S II LTE (Skyrocket). I've Googled and searched these forums, I've tried every "fix" I could but haven't found anything that specifically matches my issue here. A few months ago I did have the sticky power button issue but I don't think this is the issue here given I am not getting multiple vibrations on the reboots.
I had CM 10.2 installed and running, did a factory reset/wipe dalvik & cache/wipe system and installed AOKP 4.3. Phone was stuck in a boot loop. Restored CM backup and phone still stuck in boot loop. Used ODIN to revert to factory stock image and phone is still stuck in a boot loop. Tried clearing cache and factory reset in stock recovery and phone is still stuck in boot loop.
As far as this boot loop it flashes at the SGS II LTE "S" logo for a couple of minutes, vibrates once then reboots. As well, as soon as I insert the battery, the phone turns on, holding the power button down to turn the phone off just reboots the phone.
Also in stock recovery, I see this:
-- Verifying internal MMC block --
E:failed to mount /efs (invalid argument)
E:Mount fail : EFS partition
Not need checksum confirmation
already executed!!...
E:failed to mount /efs (invalid argument)
E:failed to mount /efs (invalid argument)
# MANUAL MODE #
-- Applying Multi-CSC...
Applied the CSC-code : unknown
Successfully applied multi-CSC.
Any thoughts/ideas/possible fixes?

pixelens said:
Having some phone issues - Samsung Galaxy S II LTE (Skyrocket). I've Googled and searched these forums, I've tried every "fix" I could but haven't found anything that specifically matches my issue here. A few months ago I did have the sticky power button issue but I don't think this is the issue here given I am not getting multiple vibrations on the reboots.
I had CM 10.2 installed and running, did a factory reset/wipe dalvik & cache/wipe system and installed AOKP 4.3. Phone was stuck in a boot loop. Restored CM backup and phone still stuck in boot loop. Used ODIN to revert to factory stock image and phone is still stuck in a boot loop. Tried clearing cache and factory reset in stock recovery and phone is still stuck in boot loop.
As far as this boot loop it flashes at the SGS II LTE "S" logo for a couple of minutes, vibrates once then reboots. As well, as soon as I insert the battery, the phone turns on, holding the power button down to turn the phone off just reboots the phone.
Also in stock recovery, I see this:
-- Verifying internal MMC block --
E:failed to mount /efs (invalid argument)
E:Mount fail : EFS partition
Not need checksum confirmation
already executed!!...
E:failed to mount /efs (invalid argument)
E:failed to mount /efs (invalid argument)
# MANUAL MODE #
-- Applying Multi-CSC...
Applied the CSC-code : unknown
Successfully applied multi-CSC.
Any thoughts/ideas/possible fixes?
Click to expand...
Click to collapse
READ THIS B4 POSTING | THE MOST Common Questions Answered HERE goto the general section for sticky power button
inserting battery turns on phone is symptom of sticky power button.
your error message idk, could be because phone wont/cant stay on long enough to mount partitions

vincom said:
READ THIS B4 POSTING | THE MOST Common Questions Answered HERE goto the general section for sticky power button
inserting battery turns on phone is symptom of sticky power button.
your error message idk, could be because phone wont/cant stay on long enough to mount partitions
Click to expand...
Click to collapse
As I mentioned, I had the sticky power button issue about 3 months ago and I resolved it then, I just mentioned it because I was unsure if my current issue might be related. I read the rest of that post before I posted here and didn't see anything regarding the EFS issue.

pixelens said:
As I mentioned, I had the sticky power button issue about 3 months ago and I resolved it then, I just mentioned it because I was unsure if my current issue might be related. I read the rest of that post before I posted here and didn't see anything regarding the EFS issue.
Click to expand...
Click to collapse
if it starts as soon as you put the battery in the power button is the prob, afaik no one ever had the phone boot up reinserting the battery no matter what the state the phone was in, I even wiped the phone then pulled/reinserted the battery and the phone did not boot up.
next prob is you probably had a bad flash, why you had a bad flash idk, maybe a bad emmc, the only way to tell is to reflash stock, but u need to get to odin mode to do that but you cant get to odin because of the bootloop, reason behind bootloop is the sticky power button.
it could be dumb luck that both things happened at the same time. try to get into odin mode by either mashing the power button or cleaning it out to solve the bootloop

I can get into download mode and Odin. I've flashed stock and it still bootloops.
TL;DR:
1. Bootloop started with fresh AOKP 4.3 install
2. Bootloop continued with CWM restore to CM 10.2
3. Bootloop continued with CM 10.2 fresh install (everything wiped, even factory reset)
4. Bootloop continued with Stock install via ODIN
5. Factory reset and wiped cache in stock recovery and bootloop continues.
I think the power button is a separate issue from the bootloop - but I did try the fixes in the power button section just in case and no change.

Please share the steps to resolve bootloop
pixelens said:
I can get into download mode and Odin. I've flashed stock and it still bootloops.
TL;DR:
1. Bootloop started with fresh AOKP 4.3 install
2. Bootloop continued with CWM restore to CM 10.2
3. Bootloop continued with CM 10.2 fresh install (everything wiped, even factory reset)
4. Bootloop continued with Stock install via ODIN
5. Factory reset and wiped cache in stock recovery and bootloop continues.
I think the power button is a separate issue from the bootloop - but I did try the fixes in the power button section just in case and no change.
Click to expand...
Click to collapse
I too have the same problem. Have you resolved it. I have tried all the steps like get into ownload mode and Odin. I've flashed stock and it still bootloop. Please share the steps if you resolved. I don't know what to do
Thanks, KamaL

kingkamal said:
I too have the same problem. Have you resolved it. I have tried all the steps like get into ownload mode and Odin. I've flashed stock and it still bootloop. Please share the steps if you resolved. I don't know what to do
Thanks, KamaL
Click to expand...
Click to collapse
Do a factory reset in recovery

[Q] Bricked P5110

Please help,http://forum.xda-developers.com/images/smilies/crying.gif
After opening an email my Samsung Tab2 10.1 GT-P5110 will not boot anymore.
message: somthing as "unable to open expresso.jpg"
I have tried te flash the factory rom result: boot to samsung logo then stopped.
I have tried te recover an old clockworkmod backup, result: it works in androud 4.0.1. ICS in factory mode
The only message i get is E:faild to mount/ efs (invalid argument)
I have tried to download the samsung update unwired and with KIES, result: nothing but samsung logo.
Is there a way to get back to android 4.2.2. in manual mode iso factory mode?
Many thanks in advance !

alexandra14 said:
Please help,http://forum.xda-developers.com/images/smilies/crying.gif
After opening an email my Samsung Tab2 10.1 GT-P5110 will not boot anymore.
message: somthing as "unable to open expresso.jpg"
I have tried te flash the factory rom result: boot to samsung logo then stopped.
I have tried te recover an old clockworkmod backup, result: it works in androud 4.0.1. ICS in factory mode
The only message i get is E:faild to mount/ efs (invalid argument)
I have tried to download the samsung update unwired and with KIES, result: nothing but samsung logo.
Is there a way to get back to android 4.2.2. in manual mode iso factory mode?
Many thanks in advance !
Click to expand...
Click to collapse
E:faild to mount/ efs (invalid argument)
============================
Means you have the incorrect version of CWM to work for your Tablet. Depending on the partitions you need to use a different CWM version.
I found this link here on XDA that should help you and be the correct version make sure you follow all the directions to this post on how to flash it to your tablet.
[RECOVERY][GT-P51XX] Unofficial ClockworkMod Recovery 6.0.4.5 (Normal + Touch)
==============================================================
http://forum.xda-developers.com/showthread.php?t=2268785
After Install of CWM Follow this:
========================
HOW TO FLASH PLEASE USE THIS ORDER TO MAKE SURE IT ALL GOES WELL.
Go to CWM or Recovery mode
Select Advanced
Select Wipe Dalvik Cache
Select Wipe Battery Stats (optional)
Go back to the previous menu
Select Wipe Data/Factory Reset
Select Wipe Cache Partition
Then Select Mounts and Storage
Select Format /System
Select Format /Cache
Select Format /Data
SHUTDOWN your tab and then go back to your bootloader mood for ODIN and reflash stock ROM again and see if that helps clean things up if it still gets stuck and you have stock recovery now just go to yoru recovery again and select WIPE DATA/FACTORY RESET & WIPE CACHE PARTITION and then reboot again.
Hope this helps.
- orbit

[Q] Moto G XT1033 not charging after bootloop

Hello guys, i have Moto G 1st Gen. Indian version (XT1033) running android 5.0.2... Yesterday i rooted my moto g by unlocking bootloader and flashing TWRP 2.8.6.0-XT1032 & SuperSU 2.45... During the process there was some error (like general unlock failure, wipe partition failure etc). I ignored them and continued... It was booted normally... Then i installed Root Checker and confirmed that root has been done successfully....
After that i tried to make a Nandroid backup using TWRP. Message popped up saying that backup is successful.. Then i pressed reboot system. Then it went into bootloop (stuck at bootloader unlocked warning message). :crying:
When this happened, i thought to flash recovery again and flash stock rom. By the time i downloaded stock rom, the phone discharged completely. Now the phone is not charging I have tried using usb charging through pc and using socket charger, but it's stuck at 0%... (I have kept it for hours) Sometime it try to boot and bootloader unlocked warning appears and stuck there.. after sometime it again go into battery charging logo with 0% and then repeat the process again.. When i try using usb cable, the same cycle continues with frequent connecting and disconnecting... :crying:
What to do now ? I guess it's not possible to flash stock rom without any charge... How to charge my phone ? What other option(s) do i have ?
PS : Sorry if this has been already discussed.

savvy54 said:
Hello guys, i have Moto G 1st Gen. Indian version (XT1033) running android 5.0.2... Yesterday i rooted my moto g by unlocking bootloader and flashing TWRP 2.8.6.0-XT1032 & SuperSU 2.45... During the process there was some error (like general unlock failure, wipe partition failure etc). I ignored them and continued... It was booted normally... Then i installed Root Checker and confirmed that root has been done successfully....
After that i tried to make a Nandroid backup using TWRP. Message popped up saying that backup is successful.. Then i pressed reboot system. Then it went into bootloop (stuck at bootloader unlocked warning message). :crying:
When this happened, i thought to flash recovery again and flash stock rom. By the time i downloaded stock rom, the phone discharged completely. Now the phone is not charging I have tried using usb charging through pc and using socket charger, but it's stuck at 0%... (I have kept it for hours) Sometime it try to boot and bootloader unlocked warning appears and stuck there.. after sometime it again go into battery charging logo with 0% and then repeat the process again.. When i try using usb cable, the same cycle continues with frequent connecting and disconnecting... :crying:
What to do now ? I guess it's not possible to flash stock rom without any charge... How to charge my phone ? What other option(s) do i have ?
PS : Sorry if this has been already discussed.
Click to expand...
Click to collapse
You must not use TWRP from its official site
Those people have not fixed this ****ty bug and many people have got bootloops due to this including me
Use the one available in xda
Solution-
Try to boot the phone in bootloader mode
Whenever the device shows the moto logo immediately press and hold power button and as soon as the screen goes black immediately press and hold power + volume down bottom and it should boot into bootloader
Charge the phone through a USB in bootloader mode
And then either flash the stock firmware again or use custom ROMs
Sent from falcon
PRESS THANKS IF HELPED?????

Okk, i was able to go into bootloader mode and charge through usb cable.. But, since then i am trying again & again to flash a rom to get my phone working but everytime something is going wrong.. First i tried to flash stock rom but it was frequently rebooting. So then i tried to flash Resurrection Remix : now it's stuck at RR logo screen for 2 hrs.. Don't know what am i doing wrong ... I am very much frustrated right now... I am now thinking to flash optimised stock rom... Some help from your side will be very helpfull :
1. Please tell me which recovery to use for peace of mind and please give me link for that.
2. I am thinking to use This stock rom to flash. ( I am facing problem with untouched version) Please tell me the exact procedure . Flash recovery > Wipe cache, dalvik, system,data in recovery > Flash rom and then do i need to flash the radio version ? And if i want to root, can i flash SuperSU after that ?
Please Note : I know that what i am asking can be found after a little bit of searching. But i have wasted 4 days and still remaining at the the same spot. Your 15 minutes time can save my another 4 days and put away my frustration i am facing right now. I am asking this because i have gone into such a state that i am thinking of throwing my phone and sleeep right away.. Please do me a favor.
My phone : Moto G 1st Gen. ( XT1033 ) , Lollipop 5.0.2, Bootloader unlocked

savvy54 said:
Okk, i was able to go into bootloader mode and charge through usb cable.. But, since then i am trying again & again to flash a rom to get my phone working but everytime something is going wrong.. First i tried to flash stock rom but it was frequently rebooting. So then i tried to flash Resurrection Remix : now it's stuck at RR logo screen for 2 hrs.. Don't know what am i doing wrong ... I am very much frustrated right now... I am now thinking to flash optimised stock rom... Some help from your side will be very helpfull :
1. Please tell me which recovery to use for peace of mind and please give me link for that.
2. I am thinking to use This stock rom to flash. ( I am facing problem with untouched version) Please tell me the exact procedure . Flash recovery > Wipe cache, dalvik, system,data in recovery > Flash rom and then do i need to flash the radio version ? And if i want to root, can i flash SuperSU after that ?
Please Note : I know that what i am asking can be found after a little bit of searching. But i have wasted 4 days and still remaining at the the same spot. Your 15 minutes time can save my another 4 days and put away my frustration i am facing right now. I am asking this because i have gone into such a state that i am thinking of throwing my phone and sleeep right away.. Please do me a favor.
My phone : Moto G 1st Gen. ( XT1033 ) , Lollipop 5.0.2, Bootloader unlocked
Click to expand...
Click to collapse
Link to recovery
http://forum.xda-developers.com/showthread.php?p=57672469
You MUST use the stock version 2.8.6.0 ( do not use the gpe version)
Do not use 2.8.6.0.1 ( it still has bugs)
Flash the recovery through fastboot
Then one by one wipe the following and tell me if any error occurs
System
Data
Cache
Dalvik cache
You must report back the error that comes in recovery logs when you wipe these partitions
Report back
Sent from falcon
PRESS THANKS IF HELPED?????

sjandroiddeveloper said:
Then one by one wipe the following and tell me if any error occurs
System
Data
Cache
Dalvik cache
You must report back the error that comes in recovery logs when you wipe these partitions
Click to expand...
Click to collapse
1. System Formatting system using make_ext4fs function.
Updating partition details.....
E: unable to stat '/data/property/.temp.sx2jrN/.last_install_path
E: unable to stat '/data/property/.temp.Md9EXT
E: unable to stat '/data/property/.temp.cCjJv7/0
E: unable to stat '/data/property/.temp.cCjJv7/legacy
E: unable to stat '/data/property/.temp.cCjJv7/0
E: unable to stat '/data/property/.temp.cCjJv7/legacy
E: unable to stat '/data/property/.temp.cCjJv7/0
E: unable to stat '/data/property/.temp.cCjJv7/ legacy
E: unable to stat '/data/property/.temp.cCjJv7/0
E: unable to stat '/data/property/.temp.cCjJv7/legacy
E: unable to stat '/data/property/.temp.9107E0
E: unable to stat '/data/property/.temp.DpW8n7
E: unable to stat '/data/property/.temp.EXVJvT
E: unable to stat '/data/property/.temp.gKptm9
E: unable to stat '/data/property/.temp. Ab0nvs
2. Data Wiping data without wiping /data/media.....
Done
Updating partition details.....
Same error as above
3. Cache and 4. Dalvik cache Same error showed up after wiping cache and Dalvik cache (wipe complete, error during updating partition...)
PS : I think this error was not present when i tried flashing stock rom or RR rom
Update Today i tried installing optimised stock rom through usb otg... Following error occured :
E; Error executing updater binary in zip <zip name> followed by same error in upadating partrition as above..

savvy54 said:
1. System Formatting system using make_ext4fs function.
Updating partition details.....
E: unable to stat '/data/property/.temp.sx2jrN/.last_install_path
E: unable to stat '/data/property/.temp.Md9EXT
E: unable to stat '/data/property/.temp.cCjJv7/0
E: unable to stat '/data/property/.temp.cCjJv7/legacy
E: unable to stat '/data/property/.temp.cCjJv7/0
E: unable to stat '/data/property/.temp.cCjJv7/legacy
E: unable to stat '/data/property/.temp.cCjJv7/0
E: unable to stat '/data/property/.temp.cCjJv7/ legacy
E: unable to stat '/data/property/.temp.cCjJv7/0
E: unable to stat '/data/property/.temp.cCjJv7/legacy
E: unable to stat '/data/property/.temp.9107E0
E: unable to stat '/data/property/.temp.DpW8n7
E: unable to stat '/data/property/.temp.EXVJvT
E: unable to stat '/data/property/.temp.gKptm9
E: unable to stat '/data/property/.temp. Ab0nvs
2. Data Wiping data without wiping /data/media.....
Done
Updating partition details.....
Same error as above
3. Cache and 4. Dalvik cache Same error showed up after wiping cache and Dalvik cache (wipe complete, error during updating partition...)
PS : I think this error was not present when i tried flashing stock rom or RR rom
Update Today i tried installing optimised stock rom through usb otg... Following error occured :
E; Error executing updater binary in zip followed by same error in upadating partrition as above..
Click to expand...
Click to collapse
It appears that all your partitions are corrupted
You need to format them
In TWRP format ( not wipe) all partitions
The option to format data partition is straight forward and given in wipe menu
For other partitions (system ,cache) go to wipe---> advanced wipe and change the file system of system and cache partition to ext4 ( don't change to anything else)
This will format them
Try this and then try to do normal wipes and see if you are successful and report back
Sent from falcon
Press thanks if helped?????

sjandroiddeveloper said:
It appears that all your partitions are corrupted
You need to format them
In TWRP format ( not wipe) all partitions
The option to format data partition is straight forward and given in wipe menu
For other partitions (system ,cache) go to wipe---> advanced wipe and change the file system of system and cache partition to ext4 ( don't change to anything else)
This will format them
Try this and then try to do normal wipes and see if you are successful and report back
Sent from falcon
Press thanks if helped
Click to expand...
Click to collapse
When i tried to format data partition same error showed up... And when i tried to change file system of system and cache partition , above it is shown that format complete , successful but in the log same error appeared..

savvy54 said:
When i tried to format data partition same error showed up... And when i tried to change file system of system and cache partition , above it is shown that format complete , successful but in the log same error appeared..
Click to expand...
Click to collapse
Try philz touch from here
https://drive.google.com/file/d/0B7lxW9DP17gNalk2Y3EtcU9JZTA/edit?usp=docslist_api
Go to wipe and format----> custom format and then try to format all partitions and see if you're successful
Sent from falcon
PRESS THANKS IF HELPED?????

sjandroiddeveloper said:
Try philz touch.
Go to wipe and format----> custom format and then try to format all partitions and see if you're successful
Sent from falcon
PRESS THANKS IF HELPED
Click to expand...
Click to collapse
Yes, now format is successful. Formatting data for first time showed some error but in second time it was successful.
So, what to do now ? I want to go to stock.. So, anything in that direction will be helpful..
Can i flash the link i have posted ? if yes, then do i need to flash radio firmware ?

savvy54 said:
Yes, now format is successful. Formatting data for first time showed some error but in second time it was successful.
So, what to do now ? I want to go to stock.. So, anything in that direction will be helpful..
Can i flash the link i have posted ? if yes, then do i need to flash radio firmware ?
Click to expand...
Click to collapse
The link you posted is not pure stock
Its optimised means it is a custom version of stock ROM
The same dev ( @lost101 ) also provides pure versions of stock rom flashable through recovery so try that if you want a pure Motorola ROM
But I suggest you to use CM 12.1 now, as its based on android 5.1.1 its always better then stock 5.0.2 in terms of stability plus you get plenty of customization options and there's already a built in root manager
And the ROM is getting better day by day
So finally its your choice
PS:- No need to flash radio
Sent from falcon
PRESS THANKS IF HELPED?????

sjandroiddeveloper said:
The link you posted is not pure stock
Its optimised means it is a custom version of stock ROM
The same dev ( @lost101 ) also provides pure versions of stock rom flashable through recovery so try that if you want a pure Motorola ROM
But I suggest you to use CM 12.1 now, as its based on android 5.1.1 its always better then stock 5.0.2 in terms of stability plus you get plenty of customization options and there's already a built in root manager
And the ROM is getting better day by day
So finally its your choice
PS:- No need to flash radio
Sent from falcon
PRESS THANKS IF HELPED
Click to expand...
Click to collapse
I already flashed that customised rom.. And also the radio firmware.. Everything is fine now..
I have always wanted to flash CM but stepped back because it is nightly build... However, i have also heard that it is very stable and you are also saying that... So, thinking of flashing that... Please give me the link which to flash & link for gapps if needed... I have just recovered my phone after a long battle and don't want to screw up now by flashing wrong rom..:fingers-crossed:
PS : I don't know how to thank you.. You are a savior man.. This is my first time in unlocking ,rooting and all that stuff and i screw up the thing.. Again, thank you for your help...:good::good:

savvy54 said:
I already flashed that customised rom.. And also the radio firmware.. Everything is fine now..
I have always wanted to flash CM but stepped back because it is nightly build... However, i have also heard that it is very stable and you are also saying that... So, thinking of flashing that... Please give me the link which to flash & link for gapps if needed... I have just recovered my phone after a long battle and don't want to screw up now by flashing wrong rom..:fingers-crossed:
PS : I don't know how to thank you.. You are a savior man.. This is my first time in unlocking ,rooting and all that stuff and i screw up the thing.. Again, thank you for your help...:good::good:
Click to expand...
Click to collapse
As a general info, just don't play with fastboot commands and now don't try to flash stock firmware through fastboot again as it most likely will mess with your partitions
And for trying different ROMs you need a backed up system and data partition with a fully working recovery, then experiment with whatever ROM you want there is no harm ( if the ROM don't boot you can force reboot and restore the backup you made)
Link to CM 12.1 nightlies
https://download.cyanogenmod.org/?device=falcon
And just so you know cm is fully stable, I have been using it for three months and I never looked back at stock ones
So flash the latest nightly
Link to Gapps
http://forum.xda-developers.com/android/software/reborn-gapps-5-t3074660
Happy flashing
Sent from falcon
PRESS THANKS IF HELPED?????