I had upgraded to 4.2 firmware (WW_epad-user-10.6.1.8) using the second method described on http://forum.xda-developers.com/showthread.php?t=2187982. This worked well and everything was working until I messed up today D: I was trying to flash SuperSU using TWRP but it couldn't recognize my Internal SD Card so I thought there might be something wrong with my installation. When I entered the bootloader I noticed the message: Key driver not found.. Booting OS. I don't know what this means. I did not read the first thread in the General section and tried to do a restore using the 4.2 firmware package. I used the "fastboot flash system blob" command and this time everything was messed up. The blue bar that appears on installation is no longer appearing and I have an "unrecoverable bootloader" error. Nothing I did worked! What should I do?? Please provide me some simple steps. I used these commands before flashing system blob...
fastboot erase boot
fastboot erase cache
fastboot erase recovery
fastboot erase system
fastboot erase userdata
This was a very stupid move on my part but I thought this would allow a clean install D: D: Please help!
gee man you completely wiped the sucker, you may be bricked =(. i would start by trying to fastboot flash the patched version of twrp. unless you can boot into twrp already then try to flash the asus package again thru twrp. also, could twrp see your internal sd before you bricked?
Sent from my ASUS Transformer Pad TF300T using xda app-developers app
markymark567 said:
gee man you completely wiped the sucker, you may be bricked =(. i would start by trying to fastboot flash the patched version of twrp. unless you can boot into twrp already then try to flash the asus package again thru twrp. also, could twrp see your internal sd before you bricked?
Sent from my ASUS Transformer Pad TF300T using xda app-developers app
Click to expand...
Click to collapse
No, that is the reason why I wiped everything (stupid move I know)...TWRP was screwed up to begin with. I flashed 2.5 JB version and it couldn't detect my internal SD card. I made sure it was the right model and everything so TWRP messed me up. I don't know how to flash a working version of TWRP since I don't know what version works with 4.2 tf300 firmware.
sonar2854 said:
No, that is the reason why I wiped everything (stupid move I know)...TWRP was screwed up to begin with. I flashed 2.5 JB version and it couldn't detect my internal SD card. I made sure it was the right model and everything so TWRP messed me up. I don't know how to flash a working version of TWRP since I don't know what version works with 4.2 tf300 firmware.
Click to expand...
Click to collapse
there is a modded 2.4.4 version i believe that sees all correctly. the post on how to root and update describe and link it. but being now you flashed the wrong one. you cant mount anything to flash correct one. i think you are s.o.l. i hope iam am wrong. good luck.
kaos420 said:
there is a modded 2.4.4 version i believe that sees all correctly. the post on how to root and update describe and link it. but being now you flashed the wrong one. you cant mount anything to flash correct one. i think you are s.o.l. i hope iam am wrong. good luck.
Click to expand...
Click to collapse
I'm not sure how to flash it...I tried fastboot flash recovery twrp.blob (2.4.4.0 v4.2). It just freezes although the cmd says it was successful
I keep getting a bootloader error (0x0000000) everytime I try and enter RCK, Android, Wipe Data... Is there a way to reinstall the bootloader? WW_epad 10.6.1.8
No mate
As of now there's no solution to that.
Do ppl ever read before they flash? I've never seen as much bricks as I've seen on this device since the new 10.6x.x Asus bootloader... it's a shame
Read read read, understand understand understand, then read more. I almost feel sorry for you guys who are "just flashing away"
FML :crying::crying:
sonar2854 said:
I keep getting a bootloader error (0x0000000) everytime I try and enter RCK, Android, Wipe Data... Is there a way to reinstall the bootloader? WW_epad 10.6.1.8
Click to expand...
Click to collapse
Bump!
I have a couple of questions.
I would like to know about your bootloader (how many icons and which ones) and whether you can still get into twrp.
tobdaryl said:
Bump!
I have a couple of questions.
I would like to know about your bootloader (how many icons and which ones) and whether you can still get into twrp.
Click to expand...
Click to collapse
Okay, so when I press Volume Down + Power, I enter the bootloader. The bootloader has three icons: RCK, Android Logo, Wipe Data. I have no access to TWRP since there is a unrecoverable bootloader error 0x0000000 when I try to enter RCK.
sonar2854 said:
Okay, so when I press Volume Down + Power, I enter the bootloader. The bootloader has three icons: RCK, Android Logo, Wipe Data. I have no access to TWRP since there is a unrecoverable bootloader error 0x0000000 when I try to enter RCK.
Click to expand...
Click to collapse
The odds are slim but let's try a couple of things.
From power off, hold power and volume down, release when you see the icons. You should see the entering fastboot message in the upper left.
fastboot -i 0x0B05 reboot bootloader
if that fails
Power off and use the same procedure.
fastboot reboot bootloader
Tell me the result.
tobdaryl said:
The odds are slim but let's try a couple of things.
From power off, hold power and volume down, release when you see the icons. You should see the entering fastboot message in the upper left.
fastboot -i 0x0B05 reboot bootloader
if that fails
Power off and use the same procedure.
fastboot reboot bootloader
Tell me the result.
Click to expand...
Click to collapse
Okay, I tried both and it doesn't work without adding a hyphen in between reboot and bootloader so reboot-bootloader. Otherwise, with the hyphen added, both work.
sonar2854 said:
Okay, I tried both and it doesn't work without adding a hyphen in between reboot and bootloader so reboot-bootloader. Otherwise, with the hyphen added, both work.
Click to expand...
Click to collapse
Sorry for that mistake. Now try rck and let's see if the bootloader is now accepted. If we are lucky the result has changed.
tobdaryl said:
Sorry for that mistake. Now try rck and let's see if the bootloader is now accepted. If we are lucky the result has changed.
Click to expand...
Click to collapse
Eh...I don't really know how to explain this but this is what happened. Once the bootloader rebooted after entering the CMD command, I pressed volume up to access RCK and there was a "blink" and there is now a green glowing square around the Android Icon. I cannot move the volume up or down (it is frozen on the Android Icon with the green square glowing), so I don't know what that "blink" was. If i try to press volume up now there is the bootloader error again.
sonar2854 said:
Eh...I don't really know how to explain this but this is what happened. Once the bootloader rebooted after entering the CMD command, I pressed volume up to access RCK and there was a "blink" and there is now a green glowing square around the Android Icon. I cannot move the volume up or down (it is frozen on the Android Icon with the green square glowing), so I don't know what that "blink" was. If i try to press volume up now there is the bootloader error again.
Click to expand...
Click to collapse
Download the 10.4.2.20 stock firmware. Unzip once and rename the resulting zip EP201_768_SDUPDATE.zip. Place this on your external sdcard and boot into your bootloader. Volume up on RCK.
tobdaryl said:
Download the 10.4.2.20 stock firmware. Unzip once and rename the resulting zip EP201_768_SDUPDATE.zip. Place this on your external sdcard and boot into your bootloader. Volume up on RCK.
Click to expand...
Click to collapse
Um, I don't have an external SD Card? The only SD Card I have is the Internal Storage
sonar2854 said:
Um, I don't have an external SD Card? The only SD Card I have is the Internal Storage
Click to expand...
Click to collapse
Uh!
Tell me what 2.5 JB version is.
Unzip 10.6.1.8 stock firmware twice and place the blob file into the directory with adb and fastboot. Boot into the bootloader and don't press anything.
fastboot -i 0x0B05 flash system blob
fastboot -i 0x0B05 reboot
if the command fails try again without -i 0x0B05
tobdaryl said:
Uh!
Tell me what 2.5 JB version is.
Unzip 10.6.1.8 stock firmware twice and place the blob file into the directory with adb and fastboot. Boot into the bootloader and don't press anything.
fastboot -i 0x0B05 flash system blob
fastboot -i 0x0B05 reboot
if the command fails try again without -i 0x0B05
Click to expand...
Click to collapse
When you say 2.5 JB version...are you talking about TWRP? I don't think TWRP is on the tablet because I can't access it. All I saw was a blink when I pressed volume up on RCK, not TWRP? I have tried flash system blob before I posted here and it did nothing. There is no progress bar when fastboot flashing =/ I think it froze. Yup it froze, just tried to do fastboot reboot-bootloader and it said failed. Also, after the system was done writing, after 2 seconds it said complete so it didn't work.
sonar2854 said:
When you say 2.5 JB version...are you talking about TWRP? I don't think TWRP is on the tablet because I can't access it. All I saw was a blink when I pressed volume up on RCK, not TWRP? I have tried flash system blob before I posted here and it did nothing.
Click to expand...
Click to collapse
I understood about twrp and flashing system blob but I thought we had been able to get stock recovery working instead of twrp.
I 'm sorry that is all I have with no sdcard and no adb.
tobdaryl said:
I understood about twrp and flashing system blob but I thought we had been able to get stock recovery working instead of twrp.
I 'm sorry that is all I have with no sdcard and no adb.
Click to expand...
Click to collapse
I have never used the stock recovery so what is it supposed to look like? Is it that dead Android with the battery because that didn't show up? I will try and get an external sd card tomorrow and try it if you think it might work. I have the 4.2 bootloader so are you sure that I should put Version V10.4.2.20 and recover using that version? Anyways, if it ends up not working, I would just like to say thank you very much for trying.
Related
Hi ppl!
First, my device failed to get the OTA Update because I deleted some system apps (see my original post).
Then I found this post where another user restored original APKs in /system/apps and managed to manually update to JB by downloading the dlpkgfile in this post.
So I proceed, restored my /system/apps (with 755 permissions), rooted with OTA RootKeeper and SuperSU, placed the dlpkgfile and command files, restarted to fastboot (Power+Vol Down) and entered Recovery mode.
The green android with the blue progress bar went for over 10 minutes, then ... the android with the RED TRIANGLE appeared
After a minute or so the device restarted, an ASUS logo with a blue progress bar ran, but then it got stuck in the ASUS logo.
I'm still able to restart to fastboot (Power+Vol Down), where a message appears:
Code:
Android cardhu-user bootloader (1.00 e) released by "US_epad-10.4.2.9-20120809" A03
, and where I have 4 choices:
1. RCK: Recovery mode, when I select this the Red Triangle appears again.
2. Android: Normal android boot, gets freeze right away
3. Fastboot USB download protocol: Tried using ADB, but don't really know what it is. Here's an image of how the device appear in my Windows PC
4. Wipe Data: Already done this, seems to wipe user data, but still gets stuck on ASUS logo
Some pictures I took of my device: http://imgur.com/I13ou http://imgur.com/Jezpn
I also tried downloading .30 firmware from ASUS website and placing the Zip contents in my SD card, then booting recovery but no luck.
It's pretty awful that everything went so bad, I'm hoping there is a solution.
Anything would be really appreciated!!!
Thanks!
benoror said:
Hi ppl!
First, my device failed to get the OTA Update because I deleted some system apps (see my original post).
Then I found this post where another user restored original APKs in /system/apps and managed to manually update to JB by downloading the dlpkgfile in this post.
So I proceed, restored my /system/apps (with 755 permissions), rooted with OTA RootKeeper and SuperSU, placed the dlpkgfile and command files, restarted to fastboot (Power+Vol Down) and entered Recovery mode.
The green android with the blue progress bar went for over 10 minutes, then ... the android with the RED TRIANGLE appeared
After a minute or so the device restarted, an ASUS logo with a blue progress bar ran, but then it got stuck in the ASUS logo.
I'm still able to restart to fastboot (Power+Vol Down), where a message appears:
Code:
Android cardhu-user bootloader (1.00 e) released by "US_epad-10.4.2.9-20120809" A03
, and where I have 4 choices:
1. RCK: Recovery mode, when I select this the Red Triangle appears again.
2. Android: Normal android boot, gets freeze right away
3. Fastboot USB download protocol: Tried using ADB, but don't really know what it is. Here's an image of how the device appear in my Windows PC
4. Wipe Data: Already done this, seems to wipe user data, but still gets stuck on ASUS logo
Some pictures I took of my device: http://imgur.com/I13ou http://imgur.com/Jezpn
I also tried downloading .30 firmware from ASUS website and placing the Zip contents in my SD card, then booting recovery but no luck.
It's pretty awful that everything went so bad, I'm hoping there is a solution.
Anything would be really appreciated!!!
Thanks!
Click to expand...
Click to collapse
You don't have a recovery to boot into
Sent from my SGH-T989 using xda app-developers app
OK, I found this tutorial about flashing ASUS firmware with fastboot: http://www.theandroidsoul.com/how-to-restore-asus-transformer-tf300t-back-to-stock/
The problem is that the following commands:
fastboot -i 0x0B05 flash system blob
fastboot -i 0x0B05 flash system US_epad-user-9.4.3.30.zip
both produce the error: "Signature mismatch"
I guess it's becaus my fastboot is newer version, since it was actually installed during the JB update, but I'm trying to flash a older .30 firmware.
I gues I will have to wait ASUS releases the new firmware for manual flashing it.
Just guessing...
benoror said:
OK, I found this tutorial about flashing ASUS firmware with fastboot: http://www.theandroidsoul.com/how-to-restore-asus-transformer-tf300t-back-to-stock/
The problem is that the following commands:
fastboot -i 0x0B05 flash system blob
fastboot -i 0x0B05 flash system US_epad-user-9.4.3.30.zip
both produce the error: "Signature mismatch"
I guess it's becaus my fastboot is newer version, since it was actually installed during the JB update, but I'm trying to flash a older .30 firmware.
I gues I will have to wait ASUS releases the new firmware for manual flashing it.
Just guessing...
Click to expand...
Click to collapse
Thank you for posting this. I wanted to try something like this with the new boot loader that came with jb but it appears flashing the older firmware will not work.
Sent from my ASUS Transformer Pad TF300T using xda app-developers app
funnel71 said:
Thank you for posting this. I wanted to try something like this with the new boot loader that came with jb but it appears flashing the older firmware will not work.
Sent from my ASUS Transformer Pad TF300T using xda app-developers app
Click to expand...
Click to collapse
You're welcome. So, do you have a clue on how to restore my older bootloader soy I can get back to .30 stock?
benoror said:
You're welcome. So, do you have a clue on how to restore my older bootloader soy I can get back to .30 stock?
Click to expand...
Click to collapse
That is exactly what I'm wanting to know if it's even possible. If I can safely downgrade, I can re-root, but I'm limited on what I can do with a locked bootloader.
Sent from my ASUS Transformer Pad TF300T using xda app-developers app
peopole!!! new firmware is out!!!
http://dlcdnet.asus.com/pub/ASUS/EeePAD/TF300T/US_epaduser_10_4_2_9_UpdateLauncher.zip
here is a direct download link!!! US version only!!!
PS: im pushing using
fastboot -i 0x0B05 flash system blob
Click to expand...
Click to collapse
[blob extracted from the above zip]
okay asus animated boot is up and i seem to successfully unbrick my device!!!!
Screens http://imgur.com/a/D7wqI
kindrudekid said:
peopole!!! new firmware is out!!!
http://dlcdnet.asus.com/pub/ASUS/EeePAD/TF300T/US_epaduser_10_4_2_9_UpdateLauncher.zip
here is a direct download link!!! US version only!!!
PS: im pushing using
[blob extracted from the above zip]
okay asus animated boot is up and i seem to successfully unbrick my device!!!!
Screens http://imgur.com/a/D7wqI
Click to expand...
Click to collapse
I don't know you mate..
But I'm so happy for you!! Glad everything worked out well! Cheers!!
Same Here!!!
Flashing the new ASUS firmware unbricked my device!!!!
Please mark this topic as SOLVED
ASUS should really make this process easier.
Thanks for all the support!
Greetings.
soft bricked?
I dont see how this is solved......I have seen some people comment they have no fastboot or recovery,
I tried to do manual update in cwm and when I rebooted with adb all I have is asus boot logo, it also does not say I have an unlocked bootloader,
I have no fastboot no recovery no adb connect all I have is asus boot logo.......volume+-power does nothing vol down + power also does nothing.
how do you flash new firmware without adb or any type of recovery?
uelabs said:
I dont see how this is solved......I have seen some people comment they have no fastboot or recovery,
I tried to do manual update in cwm and when I rebooted with adb all I have is asus boot logo, it also does not say I have an unlocked bootloader,
I have no fastboot no recovery no adb connect all I have is asus boot logo.......volume+-power does nothing vol down + power also does nothing.
how do you flash new firmware without adb or any type of recovery?
Click to expand...
Click to collapse
I have the same problem!!
please need help on this!!
AFAIK you should still have access to fastboot, I'm newbie and never messed up by unlocking the bootloader
It worked!
Thank you so much! I had this same problem with mine and couldn't find an answer anywhere until I found your post.
hmm, I lost my tablet for nearly a month then updated CM10 when prompted having connected to my new wireless. This of course (since the Oct update) put the ROM out of kilter with the bootloader. I didn't have an old ROM on the SDCARD, and old CWM so I couldn't mount an external to get a rom on. I tried pushing a rom to the SD with adb but the drivers weren't going in right and I just couldn't get any joy. I followed this thread to fastboot the current stock JB on in the hope that it would give me a fresh start but it's hanging now at the second (glossy) ASUS logo. I really don't know where to go from here. Is it possible there was a problem with the write?
erasing the memory from the boot menu worked!
biscuits said:
erasing the memory from the boot menu worked!
Click to expand...
Click to collapse
Can you tell me how you erased memory from boot menu - or maybe i understand this in different way.
I have only bootloop and it boots to CWM where i cannot mount any SD card - not internal not external.
Also Vol down + power doesnt work - there is no option to enter fastboot mode....device just bootloops and then enters CWM...
Tried to push through adb but there is no SD card to copy files. Tried different methods but cannot mount any storage...
Thanks JB update
kindrudekid said:
peopole!!! new firmware is out!!!
here is a direct download link!!! US version only!!!
PS: im pushing using
[blob extracted from the above zip]
okay asus animated boot is up and i seem to successfully unbrick my device!!!!
My fastboot is working but it seems that i cannot write anything on my internal sd card.. When i run fastboot -i 0x0B05 flash system blob
My PC shows no erros - it does all the steps. But my tablet freezes and that it - it never unfreezes, i need to power it off.
But fastboot and abd commands work - like reboot or boot into bootloader.
Click to expand...
Click to collapse
I couldn't leave well enough alone and I f'd up somehow trying to flash my pad to 4.2 stock from Cyanogen with TWRP. Now booting thru vol- and power brings up TWRP only. It asks me for a password, which it never has before. I hit cancel and it puts me into home screen. Only ray of hope I see is that ADB still recognizes it and interacts with it. I've tried pushing every ROM I can get my mitts on to the pad. When I try and install it fails after a few seconds. Then the files I just pushed are no longer on /sdcard. I don't have a clue.
Anyone, anyone? Bueller, Bueller...
dedalus2k said:
I couldn't leave well enough alone and I f'd up somehow trying to flash my pad to 4.2 stock from Cyanogen with TWRP. Now booting thru vol- and power brings up TWRP only. It asks me for a password, which it never has before. I hit cancel and it puts me into home screen. Only ray of hope I see is that ADB still recognizes it and interacts with it. I've tried pushing every ROM I can get my mitts on to the pad. When I try and install it fails after a few seconds. Then the files I just pushed are no longer on /sdcard. I don't have a clue.
Anyone, anyone? Bueller, Bueller...
Click to expand...
Click to collapse
Make sure you have flashed the correct version of TWRP. as there are three different versions on their website. If you are confident you have flashed correct TWRP version then you may need to downgrade to the previous version of TWRP. I had a similar issue I downgraded to 2.4.4.0 JB build. Hope this helps
"...you may need to downgrade to the previous version of TWRP."
I can't get into fastboot to install an earlier version. I think I'm screwed.
Theoretically I could use TWRP to totally wipe the pad and then ADB to push the system files back on, but... I don't have that kind of tech knowledge and I doubt anyone who doesn't work for ASUS does.
Edit: My mistake. You can use ADB to install TWRP. I'll give it a shot, though I'm pretty damn sure it's a long one.
dedalus2k said:
"...you may need to downgrade to the previous version of TWRP."
I can't get into fastboot to install an earlier version. I think I'm screwed.
Theoretically I could use TWRP to totally wipe the pad and then ADB to push the system files back on, but... I don't have that kind of tech knowledge and I doubt anyone who doesn't work for ASUS does.
Edit: My mistake. You can use ADB to install TWRP. I'll give it a shot, though I'm pretty damn sure it's a long one.
Click to expand...
Click to collapse
Hey dude just thought I make it easier to understand if you have 3 icons then you will pre load into fastboot if you have four icons then you will have to load fastboot. Lemme know if you run into problems. Happy to help mate.
anaschillin said:
Hey dude just thought I make it easier to understand if you have 3 icons then you will pre load into fastboot if you have four icons then you will have to load fastboot. Lemme know if you run into problems. Happy to help mate.
Click to expand...
Click to collapse
I don't get three or four icons. It boots directly into TWRP. ADB still recognizes the pad and I can still push files to /sdcard. I tried reflashing the ROM but it fails after just a couple seconds, shuts down and boots back into TWRP.
I'm going to get a flashcard reader today and format my external card FAT32 and see if I can't install a new ROM from that.
im in a different situation
i did a erase system in fastboot
now i can only go to fastboot with preload on it
or
apx
is there any wait i can fix it and bring it back to live
Update: Bought a card reader at local Discount Electronics. Plugged it into my PC and it promptly froze my computer and destroyed my $80 64G sd card. Can't catch a break here. So I need to get another card and reader before I can attempt to install rom from external card.
The card reader is by a company called Zeikos. http://www.amazon.com/electronics/dp/B001T9N0R6 You have been warned.
Sheena0220 said:
im in a different situation
i did a erase system in fastboot
now i can only go to fastboot with preload on it
or
apx
is there any wait i can fix it and bring it back to live
Click to expand...
Click to collapse
Can you flash a recovery...
if you manage to flash a recovery run the command: fastboot reboot recovery.
dedalus2k said:
I don't get three or four icons. It boots directly into TWRP. ADB still recognizes the pad and I can still push files to /sdcard. I tried reflashing the ROM but it fails after just a couple seconds, shuts down and boots back into TWRP.
I'm going to get a flashcard reader today and format my external card FAT32 and see if I can't install a new ROM from that.
Click to expand...
Click to collapse
adb reboot bootloader
or
fastboot -i 0x0B05 reboot-bootloader
or
from android terminal - you must be rooted for this to work
su
reboot bootloader
tobdaryl said:
adb reboot bootloader
or
fastboot -i 0x0B05 reboot-bootloader
or
from android terminal - you must be rooted for this to work
su
reboot bootloader
Click to expand...
Click to collapse
I'll give the first one a shot. I can't get into fastboot mode and the su command comes up an error even though I am rooted or was. I really can't figure out where it all went haywire.
YES! I'm in!
tobdaryl said:
adb reboot bootloader
or
fastboot -i 0x0B05 reboot-bootloader
or
from android terminal - you must be rooted for this to work
su
reboot bootloader
Click to expand...
Click to collapse
You are a god amongst men! Thank you sooooo much. If you don't mind...now what?
I get the following messages:
Key driver not found..Booting OS
Android cardhu-user bootloader <1.00e> released by "WW_epad-10.6.1.15.3-20130416" A03
Starting Fastboot USB download protocol
and then the three icons, RCK android and Wipe Data.
After this mishap I don't trust myself to weed through the mountains of info here again. I'm trying to reinstall 4.2.1 and keep it rooted. I'm assuming reinstall 4.2.1 and then reroot, yes? Would you mind terribly pointing me to a reliable post I can follow.
Thank You so much!!!
dedalus2k said:
You are a god amongst men! Thank you sooooo much. If you don't mind...now what?
I get the following messages:
Key driver not found..Booting OS
Android cardhu-user bootloader <1.00e> released by "WW_epad-10.6.1.15.3-20130416" A03
Starting Fastboot USB download protocol
and then the three icons, RCK android and Wipe Data.
After this mishap I don't trust myself to weed through the mountains of info here again. I'm trying to reinstall 4.2.1 and keep it rooted. I'm assuming reinstall 4.2.1 and then reroot, yes? Would you mind terribly pointing me to a reliable post I can follow.
Thank You so much!!!
Click to expand...
Click to collapse
You will have to reroot but with motochopper that is minor.
Unzip 10.6.1.15.3 till you have a blob file. Place the blob in the directory with fastboot.
Reboot into bootloader and wait for fastboot to start. (watch the upper left of the screen)
fastboot -i 0x0B05 flash system blob - wait for the flash to finish then
fastboot -i 0x0B05 reboot
Good Luck!
tobdaryl said:
You will have to reroot but with motochopper that is minor.
Unzip 10.6.1.15.3 till you have a blob file. Place the blob in the directory with fastboot.
Reboot into bootloader and wait for fastboot to start. (watch the upper left of the screen)
fastboot -i 0x0B05 flash system blob - wait for the flash to finish then
fastboot -i 0x0B05 reboot
Good Luck!
Click to expand...
Click to collapse
Grazie Mille! Gonna give it a go right now.
Should I bother with TWRP? I tried to update it before and that's the point it went to hell last time.
tobdaryl said:
You will have to reroot but with motochopper that is minor.
Unzip 10.6.1.15.3 till you have a blob file. Place the blob in the directory with fastboot.
Reboot into bootloader and wait for fastboot to start. (watch the upper left of the screen)
fastboot -i 0x0B05 flash system blob - wait for the flash to finish then
fastboot -i 0x0B05 reboot
Good Luck!
Click to expand...
Click to collapse
Okay. I did it. No joy.
erasing 'system'...
OKAY [2.544s]
sending 'system' <800927 KB>
OKAY [136.994s]
writing 'system'...
OKAY [3.151s]
finished. total time 142.707s
fire off the reboot command
rebooting...
finished. total time 0.551s
But the tab doesn't reboot. And that short "writing 'system'" time to me sounds mighty suspicious
Any ideas? I'm afraid to force reboot it.
dedalus2k said:
Okay. I did it. No joy.
erasing 'system'...
OKAY [2.544s]
sending 'system' <800927 KB>
OKAY [136.994s]
writing 'system'...
OKAY [3.151s]
finished. total time 142.707s
fire off the reboot command
rebooting...
finished. total time 0.551s
But the tab doesn't reboot. And that short "writing 'system'" time to me sounds mighty suspicious
Any ideas? I'm afraid to force reboot it.
Click to expand...
Click to collapse
Reboot into the bootloader. If you get into the bootloader cold boot - volume down on the first icon.
If your tablet fails to boot into android go back to the bootloader and reboot into recovery.
I'll wait for your response.
tobdaryl said:
Reboot into the bootloader. If you get into the bootloader cold boot - volume down on the first icon.
If your tablet fails to boot into android go back to the bootloader and reboot into recovery.
I'll wait for your response.
Click to expand...
Click to collapse
Done and no luck
dedalus2k said:
Done and no luck
Click to expand...
Click to collapse
No recovery either?
What happens in both cases - please explain.
tobdaryl said:
No recovery either?
What happens in both cases - please explain.
Click to expand...
Click to collapse
From off state it always boots into TWRP. I stupidly installed an older version on accident. 2.2.2
With your help I was able to boot into fastboot with the adb command. I've run installs of both the ROM and tried an update to TWRP. According to the console everything went fine but when I give it the reboot command nothing happens. Somewhere in there it looses connections with the tablet it seems.
dedalus2k said:
From off state it always boots into TWRP. I stupidly installed an older version on accident. 2.2.2
With your help I was able to boot into fastboot with the adb command. I've run installs of both the ROM and tried an update to TWRP. According to the console everything went fine but when I give it the reboot command nothing happens. Somewhere in there it looses connections with the tablet it seems.
Click to expand...
Click to collapse
Please explain what happens now. Can you get into the bootloader, recovery, etc?
If you get into the bootloader what happens when you cold boot?
When you boot now without any intervention does it still boot twrp?
tobdaryl said:
Please explain what happens now. Can you get into the bootloader, recovery, etc?
If you get into the bootloader what happens when you cold boot?
When you boot now without any intervention does it still boot twrp?
Click to expand...
Click to collapse
Excuse my noobishness.
I can get into bootloader with the adb reboot bootloader command you gave me
When I go to recovery, RCK right?, it freezes up.
From cold boot it goes directly into TWRP, which asks for a password which it hasn't ever before this mishap.
If I go to android from bootloader and it goes to TWRP as well
tf300t unroot with android 4.2.1
running in 10.6.1.15.3
system always boot to cwm
from pc using cmd using adb reboot-bootloader
in the fastboot mode
with no usb icon
unable to flash with anything
not even able to cold boot
just only able to boot to cwm v6.0.2.3
each time need to cmd to boot to fastboot but no usb icon
any idea
question is this mean im in brick
Sheena0220 said:
tf300t unroot with android 4.2.1
running in 10.6.1.15.3
system always boot to cwm
from pc using cmd using adb reboot-bootloader
in the fastboot mode
with no usb icon
unable to flash with anything
not even able to cold boot
just only able to boot to cwm v6.0.2.3
each time need to cmd to boot to fastboot but no usb icon
any idea
question is this mean im in brick
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?p=42011887#post42011887 - read this post and let me know if you have any questions.
it doesnt work for me
i did exactly how you say
place the unzip file to sdcard
place the sd card to the side of the mmsd slot
reboot the tablet
nothing happen
even try to reboot in the fastboot mode and press the up button at he rck mode
still no go
i just have no idea how i got to the point that the bootloader fail went i in the fastboot->rck
show that fail bootloader with (0x000000000)
i can only get to APX mode and Fastboot using pc (but i cant do nothing to it) it doesnt show the usb icon
i can read the tablet
but i cant write anything to it
im still waiting for something happen
hope one of this master
have a software and about to bring back to live
Sheena0220 said:
it doesnt work for me
i did exactly how you say
place the unzip file to sdcard
place the sd card to the side of the mmsd slot
reboot the tablet
nothing happen
even try to reboot in the fastboot mode and press the up button at he rck mode
still no go
i just have no idea how i got to the point that the bootloader fail went i in the fastboot->rck
show that fail bootloader with (0x000000000)
i can only get to APX mode and Fastboot using pc (but i cant do nothing to it) it doesnt show the usb icon
i can read the tablet
but i cant write anything to it
im still waiting for something happen
hope one of this master
have a software and about to bring back to live
Click to expand...
Click to collapse
The previous link you were provided only works with stock recovery not cwm or twrp.
The 4.2 bootloader (10.6.?.?.?) does not have a usb icon. When you get to the bootloader press no buttons and wait for notification in the upper left - entering fastboot.
Sheena0220 said:
it doesnt work for me
i did exactly how you say
place the unzip file to sdcard
place the sd card to the side of the mmsd slot
reboot the tablet
nothing happen
even try to reboot in the fastboot mode and press the up button at he rck mode
still no go
i just have no idea how i got to the point that the bootloader fail went i in the fastboot->rck
show that fail bootloader with (0x000000000)
i can only get to APX mode and Fastboot using pc (but i cant do nothing to it) it doesnt show the usb icon
i can read the tablet
but i cant write anything to it
im still waiting for something happen
hope one of this master
have a software and about to bring back to live
Click to expand...
Click to collapse
http://www.androidauthority.com/transformer-pad-tf300t-restore-stock-firmware-108016/ = try this method. this is the fastboot method. FYI, as sheena said, you dont need to see the usb icon. immediately u boot into the bootloader, the tablet enters fastboot mode. if you need more detailed instructios, add me on skype or facebook. i'll be glad to help.
crazynitro said:
http://www.androidauthority.com/transformer-pad-tf300t-restore-stock-firmware-108016/ = try this method. this is the fastboot method. FYI, as sheena said, you dont need to see the usb icon. immediately u boot into the bootloader, the tablet enters fastboot mode. if you need more detailed instructios, add me on skype or facebook. i'll be glad to help.
Click to expand...
Click to collapse
thx for the instruction
i will try it tonight
i think i see somewhere before and try it before with the code in the cmd
at fastboot
while the tablet still flashing with the 3 icon (rck, android, and wipe data)
in pc i type this code as follow
fastboot device
come out the sn #
fastboot -i 0x0b05 flash system blob
then the tablet freeze but the cmd is say success
but i try only one or two time
at this moment i only able to boot in to fastboot by hard reset and the APX
in APX mode the pc didnt recognize the driver
also i try couple at fastboot mode in tablet i hit the upper vol at RCK
it return message as follow
bootloader fail
code is 0X 00000000
i know it is not in brick
the system has no os to boot too
and the tablet has no wait to write anything into it
but i will try the method you have instruct tonight at see any chance
hope no need to send back to the shop to fix it
Sheena0220 said:
thx for the instruction
i will try it tonight
i think i see somewhere before and try it before with the code in the cmd
at fastboot
while the tablet still flashing with the 3 icon (rck, android, and wipe data)
in pc i type this code as follow
fastboot device
come out the sn #
fastboot -i 0x0b05 flash system blob
then the tablet freeze but the cmd is say success
but i try only one or two time
at this moment i only able to boot in to fastboot by hard reset and the APX
in APX mode the pc didnt recognize the driver
also i try couple at fastboot mode in tablet i hit the upper vol at RCK
it return message as follow
bootloader fail
code is 0X 00000000
i know it is not in brick
the system has no os to boot too
and the tablet has no wait to write anything into it
but i will try the method you have instruct tonight at see any chance
hope no need to send back to the shop to fix it
Click to expand...
Click to collapse
i had try the method
tablet freeze as soon as i start the code of
fastboot -i 0x0B05 flash system blob
i do see in cmd say finish and ok
i try code of fastboot -i 0x0B05 reboot
tablet didnt response
try fastboot devices
come back will
??????????????????? list
i just dont know what to do
it freeze all the time as i write something into tablet
Sheena0220 said:
i had try the method
tablet freeze as soon as i start the code of
fastboot -i 0x0B05 flash system blob
i do see in cmd say finish and ok
i try code of fastboot -i 0x0B05 reboot
tablet didnt response
try fastboot devices
come back will
??????????????????? list
i just dont know what to do
it freeze all the time as i write something into tablet
Click to expand...
Click to collapse
which firmware did you download? have you tried flashing a recovery img like twrp?
crazynitro said:
which firmware did you download? have you tried flashing a recovery img like twrp?
Click to expand...
Click to collapse
i use us one and get the blob out
i think i got what you mean now
i have to have the right blob before i can get the flash work if not i will freeze it
the problem is i cant even boot to android
so i have no clue on will firmware i using
all i can see from now is at the fastboot that only is us ...10.6....
is that the firmware i have to flash if do so i will try
i cant even flash the twrp into the tablet
i try blob and img
it wont work
i try the version is the 2.5......4.2.blob or img
it just got no luck at all
thx thx thx
Sounds like you flashed the incorrect twrp for your bootloader, flashing a non-4.2 twrp on a 4.2 bootloader can cause a fastboot flash brick.
Here's a little info about the changes from a 4.1 to a 4.2 bootloader as there have been quite a few bricks here over the last few months.
Still not sure of the exact issue here but seems there was a change in some or all of the partition tables with the 4.2 bootloaders for both 10.6.1.8 & 10.6.1.15.3 and as a result after updating to 4.2 and then flashing TWRP (non-4.2 version) or CWM recovery would give the following outcome when you boot to recovery.
TWRP would ask for a password on boot, you can hit cancel but are left not being able to mount any partition including external apart from possible system.
CWM was the same, unable to mount any partition.
The device will now also likely boot strait to recovery, and if you have not wiped system you will now have to cold boot andriod from now on.
Now the bad part - In about 90% of cases flashing TWRP (non-4.2 version) or CWM would also result in a fastboot flash brick, meaning that some other fastboot commands will work ok, however any fastboot flash command will look to go ok on the command prompt but you will no longer get the blue progress bar on the tablet and nothing will flash to the tablet. So your either stuck with the current os and have to cold boot or if you wiped your system your just stuck.
Only solution so far to this issue is to replace your motherboard. Here's a thread on the issue http://forum.xda-developers.com/show....php?t=2179874
And thus the -4.2 versions of TWRP were made for the 4.2 bootloaders
JB 4.2 bootloaders require the -4.2 versions of twrp
- JB 4.2.1 - 10.6.1.8 = twrp 2.4.4.0-4.2
- JB 4.2.1 - 10.6.1.15.3 = twrp 2.5.0.0-4.2
So if you do not get the blue progress bar on tablet when running a fastboot flash command then sorry to say you have the fastboot flash brick.
There are many many threads/posts on this issue with the above info but still people are not reading, bricking there tablets and creating duplicate upon duplicate threads on this issue, so please look through the threads first, read, read and read some more and if still not sure ask as many questions as you need.
Hope this helps explain what has happened and why the fastboot flash command freezes your tablet.
ok thx for everyone that give a great advice
i just change a new motherbooard
and now the tablet is in a unroot and unlock
i just want a instruction on how to do the unlock and root correctly
i read so many post
i just confuse
im in a android 4.2.1
and us 10.6.1.15.3
any suggestion before i got mess up
Well, I was using an app called screen dimmer, and did pressed the button to dim the screen when all of a sudden it froze. It was like this for a while so I restarted it, it is able to go in fastboot, but nothing else. When i start It it hangs on the boot loader screen and can stay like that all day. if I go into recovery the screen goes black and the display is only backlit. I was going to try to to use the adb to factory reset it, but I could not get it to recognize the nexus 5 as a device. I used a bunch of different drivers. I did root my phone, and have the exposed framework but this was done a long time ago and I had no problems since. no idea how to fix this any help?!?!? Sorry if this is the wrong place to put this I'm new to this site.
2point said:
Well, I was using an app called screen dimmer, and did pressed the button to dim the screen when all of a sudden it froze. It was like this for a while so I restarted it, it is able to go in fastboot, but nothing else. When i start It it hangs on the boot loader screen and can stay like that all day. if I go into recovery the screen goes black and the display is only backlit. I was going to try to to use the adb to factory reset it, but I could not get it to recognize the nexus 5 as a device. I used a bunch of different drivers. I did root my phone, and have the exposed framework but this was done a long time ago and I had no problems since. no idea how to fix this any help?!?!? Sorry if this is the wrong place to put this I'm new to this site.
Click to expand...
Click to collapse
You need to find a driver that works so it'll recognize the device. Once you do this, you need to flash boot.img to restore the recovery since not working. Then, redo the ROM or restore from backup if you can. Flashing a new recovery boot.img should fix the issue.
2point said:
Well, I was using an app called screen dimmer, and did pressed the button to dim the screen when all of a sudden it froze. It was like this for a while so I restarted it, it is able to go in fastboot, but nothing else. When i start It it hangs on the boot loader screen and can stay like that all day. if I go into recovery the screen goes black and the display is only backlit. I was going to try to to use the adb to factory reset it, but I could not get it to recognize the nexus 5 as a device. I used a bunch of different drivers. I did root my phone, and have the exposed framework but this was done a long time ago and I had no problems since. no idea how to fix this any help?!?!? Sorry if this is the wrong place to put this I'm new to this site.
Click to expand...
Click to collapse
Hi, In first place, You are in the right place to get help:good:
2. ADB won't work on fastboot nor in a damaged recovery.
3. fastboot works:victory: Try to flash recovery once again (fastboot flash recovery recoveryname.img)
4. if 3 works, wipe system, caches. Flash the Rom you want, don't use that app anymore.
GUGUITOMTG4 said:
Hi, In first place, You are in the right place to get help:good:
2. ADB won't work on fastboot nor in a damaged recovery.
3. fastboot works:victory: Try to flash recovery once again (fastboot flash recovery recoveryname.img)
4. if 3 works, wipe system, caches. Flash the Rom you want, don't use that app anymore.
Click to expand...
Click to collapse
Thanks! got to recognize any way to do this without loosing data?
2point said:
Thanks! got to recognize any way to do this without loosing data?
Click to expand...
Click to collapse
There is a chance to keep your data + storage contents. If you manage to flash and boot into recovery, in 'wipe' menu manually check-mark "cache,system"
don't mark internal "storate and data", nothing will happen to your media and apps data.
2point said:
Thanks! got to recognize any way to do this without loosing data?
Click to expand...
Click to collapse
May be able to dirty flash but most likely, since you had the screen dimmed too much, you'll have to wipe data in order to override/remove the problem. You can try this way but may just send you back through this whole process if problem reoccurs. I'd just wipe the data to be safe.
2point said:
Well, I was using an app called screen dimmer, and did pressed the button to dim the screen when all of a sudden it froze. It was like this for a while so I restarted it, it is able to go in fastboot, but nothing else. When i start It it hangs on the boot loader screen and can stay like that all day. if I go into recovery the screen goes black and the display is only backlit. I was going to try to to use the adb to factory reset it, but I could not get it to recognize the nexus 5 as a device. I used a bunch of different drivers. I did root my phone, and have the exposed framework but this was done a long time ago and I had no problems since. no idea how to fix this any help?!?!? Sorry if this is the wrong place to put this I'm new to this site.
Click to expand...
Click to collapse
Oy vey! You shouldn't have been tinkering as you clearly don't know what you're doing.
[TUTORIAL] How to flash a factory image | Return to stock | Unroot your Nexus 5
2point said:
Thanks! got to recognize any way to do this without loosing data?
Click to expand...
Click to collapse
No, and if you had done your homework you would know that. If the data is so important, back it up before modding.
GUGUITOMTG4 said:
There is a chance to keep your data + storage contents. If you manage to flash and boot into recovery, in 'wipe' menu manually check-mark "cache,system"
don't mark internal "storate and data", nothing will happen to your media and apps data.
Click to expand...
Click to collapse
When I do fastboot boot recovery.img I get the android bot with a red exclamation but nothing else I might just do flashall
2point said:
When I do fastboot boot recovery.img I get the android bot with a red exclamation but nothing else I might just do flashall
Click to expand...
Click to collapse
Reflash the recovery.img
2point said:
When I do fastboot boot recovery.img I get the android bot with a red exclamation but nothing else I might just do flashall
Click to expand...
Click to collapse
The general idea is that your recovery is broken.
So, you need to flash a new recovery by placing a recovery.img file into your fastboot folder in the computer(recommend twrp). Like you did the first time you fladhed a recovery.
Then, turn off the phone, press volume down+ power button and it will boot into bootloader. Make sure it is on fastboot mode. After that, on the computer open cmd on the fastboot folder and and type:
fastboot flash recovery nameofrecoveryfile.img,
press enter.
It should flash a new recovery image if done correctly. Then, poweroff the phone, boot again into bootloader, choose recovery and it will reboot into recovery. Then follow. The steps of my first post.
jd1639 said:
Reflash the recovery.img
Click to expand...
Click to collapse
GUGUITOMTG4 said:
The general idea is that your recovery is broken.
So, you need to flash a new recovery by placing a recovery.img file into your fastboot folder in the computer(recommend twrp). Like you did the first time you fladhed a recovery.
Then, turn off the phone, press volume down+ power button and it will boot into bootloader. Make sure it is on fastboot mode. After that, on the computer open cmd on the fastboot folder and and type:
fastboot flash recovery nameofrecoveryfile.img,
press enter.
It should flash a new recovery image if done correctly. Then, poweroff the phone, boot again into bootloader, choose recovery and it will reboot into recovery. Then follow. The steps of my first post.
Click to expand...
Click to collapse
Did that and get a
C:\Users\nkkou_000\programs\adt-bundle-windows-x86_64-20131030\sdk\platform-tool
s>fastboot flash recovery openrecovery-twrp-2.6.3.4-hammerhead.img
sending 'recovery' (13272 KB)...
OKAY [ 0.620s]
writing 'recovery'...
FAILED (remote: flash write failure)
finished. total time: 44.593s
C:\Users\nkkou_000\programs\adt-bundle-windows-x86_64-20131030\sdk\platform-tool
s>
But I can do fastboot boot openrecovery-twrp-2.6.3.4-hammerhead.img and will will boot into the recovery just fine
And that twrp says that i have no os installed
2point said:
But I can do fastboot boot openrecovery-twrp-2.6.3.4-hammerhead.img and will will boot into the recovery just fine
And that twrp says that i have no os installed
Click to expand...
Click to collapse
You have a couple of options depending on how much data you can afford to lose on your phone. The least intrusive is to adb push a Rom on to your phone when you're in twrp Then flash that rom in twrp
The easier, but you'll lose all data on your phone is to flash the flash-all.bat file in fastboot
Sent from my SAMSUNG-SGH-I957 using xda app-developers app
2point said:
But I can do fastboot boot openrecovery-twrp-2.6.3.4-hammerhead.img and will will boot into the recovery just fine
And that twrp says that i have no os installed
Click to expand...
Click to collapse
Then, it seems recovery now is good. If you have rom zip in the storage. Just wipe system and cache, flash the rom and see what happens
When in the twrp I can't get fastboot to recognize it as a device, or adb either
2point said:
When in the twrp I can't get fastboot to recognize it as a device, or adb either
Click to expand...
Click to collapse
Your adb drivers aren't setup correctly. They're different than the fastboot ones. Try Google tool adb fastboot drivers xda.
jd1639 said:
Your adb drivers aren't setup correctly. They're different than the fastboot ones. Try Google tool adb fastboot drivers xda.
Click to expand...
Click to collapse
When you are on twrp. You dont need to use fastboot nor adb. Just flash a rom if have one to flash
GUGUITOMTG4 said:
When you are on twrp. You dont need to use fastboot nor adb. Just flash a rom if have one to flash
Click to expand...
Click to collapse
How do i do that?
2point said:
How do i do that?
Click to expand...
Click to collapse
Have you flashed roms before? And do you have one on your internal sdcard? If so flash it in twrp
jd1639 said:
Have you flashed roms before? And do you have one on your internal sdcard? If so flash it in twrp
Click to expand...
Click to collapse
I have the factory image from google for my nexus 5
I may have bricked, want to know what went wrong and if it's permanent. Thanks, here's how it happened.
I was running one of the Omnirom nightly builds. I got a notification saying there was a new build, I decided to try it hoping it would improve my battery life. I had TWRP installed so I thought it would be ok (I chose to let it update automatically which I guess was my mistake). It did the update or tried to at least, but when it tried to boot it just gets stuck on the Asus screen. The one with the loading bar. Volume up or down with power button does nothing but get back to the same screen. Reset (using a pin) and volume up or down does the same thing. I thought the only way to permanently boot was doing the wipe option on the recovery menu, but maybe I am wrong. Is it possible to permanently brick doing what I did? Thanks. Any possible solutions?
mechz01 said:
Is it possible to permanently brick doing what I did? Thanks. Any possible solutions?
Click to expand...
Click to collapse
Unlikely. What always works, if you can put it into fastboot, is install the Asus stock ROM. That will reformat/reinstall every partition.
Berend de Boer said:
Unlikely. What always works, if you can put it into fastboot, is install the Asus stock ROM. That will reformat/reinstall every partition.
Click to expand...
Click to collapse
That's holding the reset button down plus volume down right? Doesn't seem to work.
mechz01 said:
That's holding the reset button down plus volume down right? Doesn't seem to work.
Click to expand...
Click to collapse
Try long holding VOL DOWN & POWER BUTTON ....
Can you get to the bootloader this way ?
Thx Josh
lj50036 said:
Try long holding VOL DOWN & POWER BUTTON ....
Can you get to the bootloader this way ?
Thx Josh
Click to expand...
Click to collapse
Thanks for the Reply
No, it just gets me back to the same screen. This is supposed to get me to the recovery menu right?
If it matters,my bootloader is unlocked.
mechz01 said:
Thanks for the Reply
No, it just gets me back to the same screen. This is supposed to get me to the recovery menu right?
If it matters,my bootloader is unlocked.
Click to expand...
Click to collapse
Well there is not much that can be done then.....
No fastboot with a locked bootloader .....
No bootloader to boot into recoovery .....
No nvflash blobs with a locked bootloader ..
Short of a motherboard you have a paperweight .....
Sorry for the back news ......
Thx Josh
Hello
Hi
I had basically the same situation of this topic, the only i can access to fastboot.
I formated all my tablet, basically is nothing in the memory
when i tried to access over the recovery, is stuck, only blink.
Fastboot commands works but i dont know how i can recover all.
I know i need to install everything.
Can someone let me know what i can install (Kernel, firmware, rom(I want lollipop).
I had already TWRP 2.8.0
Thanks in advance
lj50036 said:
Well there is not much that can be done then.....
No fastboot with a locked bootloader .....
No bootloader to boot into recoovery .....
No nvflash blobs with a locked bootloader ..
Short of a motherboard you have a paperweight .....
Sorry for the back news ......
Thx Josh
Click to expand...
Click to collapse
My bootloader is unlocked, unless I am misunderstanding what you're saying. On the Asus screen it says this device is unlocked. Not sure why I can't access any of the options though, unless my volume buttons is busted or something.
jcbeau09 said:
Hi
I had basically the same situation of this topic, the only i can access to fastboot.
I formated all my tablet, basically is nothing in the memory
when i tried to access over the recovery, is stuck, only blink.
Fastboot commands works but i dont know how i can recover all.
I know i need to install everything.
Can someone let me know what i can install (Kernel, firmware, rom(I want lollipop).
I had already TWRP 2.8.0
Thanks in advance
Click to expand...
Click to collapse
First step: Install new TWRP
1. Download TWRP recovery from here: http://techerrata.com/browse/twrp2/tf300t; I would advise v. 2.8.4.0
2. Put 'openrecovery-twrp-2.8.3.0-tf300t.blob' in fastboot folder of pc and rename to twrp.blob for faster typing.
3. Put tab in fasboot mode and connect.
4. Use command
Code:
fastboot -i 0x0b05 flash staging twrp.blob[enter]
fastboot -i 0x0b05 reboot[enter]
5. Let tab reboot to OS (will stay on ASUS screen, because you don't have OS as of now).
6. Reboot to bootloader screen and go to recovery (RCK); now you can flash any custom ROM you like.
Good luck!
mechz01 said:
No, it just gets me back to the same screen. This is supposed to get me to the recovery menu right?
Click to expand...
Click to collapse
No! Recovery comes way after fastboot mode. Recovery is loaded from your memory card. But something went wrong with your memory card, so you can't load that.
Once you booted your tablet into fastboot, type :"fastboot devices" on your PC. If it shows your tablet, you can easily flash a new ROM.
Berend de Boer said:
No! Recovery comes way after fastboot mode. Recovery is loaded from your memory card. But something went wrong with your memory card, so you can't load that.
Once you booted your tablet into fastboot, type :"fastboot devices" on your PC. If it shows your tablet, you can easily flash a new ROM.
Click to expand...
Click to collapse
I would like to know how you are going to flash a new rom with fastboot ?
Thx Josh