Related
hi! my apologies but i searched and read alot of post already on how to solve this.
i flashed Roach latest CMW how ever being so stupid i forgot to put a ROM on internal memory. did full wipe already and i have no ROM to flash as it reads internal memory only.
ive read alot of post regarding the concern, i want to try to push a ROM on internal drive using ADB but when i run "adb devices" nothing is found.
any suggestions or any links to posts that i might get help or tutorial. im not an expert on using ADB so keep instructions simple, im a noob i admit it but i just need help. thanks!
read through posts "[Troubleshooting/Solved] ClockworkMod recovery 5.5.0.4 from Koush" "Used roach's new CWM recovery, now can't intall rom" "
im on recovery and when i run adb devices it just blank. any walk through is much appreciated!
Do yo have USB debugging on?
I dont know because i was about to flash a new rom so i did a full wipe already
Did you ever get ADB working before all this? USB debugging usually have to be turn on by the user. In Settings>Developer options.
i havent with my tablet but with my htc desire hd i used adb. and when ever i flash a ROM on my tf i usually turn on usb debugging always. right now in on recovery roach r2. my ROM is on my external memory. also tried to do a nvflash how ever whenever i run the download.bat cmd opens then closes 3 secs maybe
i also got a new sdk from this forum " [GUIDE] Getting ADB Setup; An Idiots' proof guide on getting ADB working for Rooting!" as ave said above when i type "adb devices" its just blank and does not list any device.
I had exactly the same problem - I'm not sure about tablet version that I own, but I've flashed Wipe Lite and new Recovery. I also have HTC phone that I've been using on the same PC .
I've spent an hour trying to get my TF back on feet and I managed it.
I would recommend uninstalling all HTC and ASUS software and drivers, rebooting PC and installing just ASUS PC Suite. It worked in my case - suddenly Device ID showed up for a few seconds before ADB reported "no device" again.
So I've pushed Rogue XM Recovery to data/media:
adb push roguexm data/media
Of course use name of zip file instead "roguexm" in command above.
After that zip file showed up on sdcard and I could flash it - it doesn't support AROMA but it works quite fine otherwise.
Hope it'll work in your case. Good luck!
Hope it will help
I once were in your case, did full wipe and forgot to put a Rom in internal memory. But in my case I just rebooted the transformer and all of a supprise, my tablet reverted to the stock Rom! I dont know how this happend but may be Asus did something to keep stock Rom persistent whatever you have flashed roms or CWMs.
So i hope this also happened in your case, just give it a try. Good luck!
If he did "Full Wipe - factory reset" then he should be able to boot HC/ICS and from that copy files onto internal /sdcard.
But if he used Android Revolution Super Wipe script either Lite or Full then he has nothing to boot into, no system at all - I've done that Only thing that left was recovery without external sdcard support, so I had nothing to install...
ASUS and HTC drivers have some issues and make everything harder than it should be, that's why I recommend to uninstall all HTC and ASUS software, rebooting PC and installing ASUS PC Suite only, to have "clean" drivers on PC.
I've tried different drivers and none of them worked, until I've done that.
Ok, I'll try to write it simple, I'm not sure if I can post links so just in case I'll give thread names. If it will be too simple don't get mad - ok?
1. Uninstall ASUS and HTC software, reinstall ASUS software like mentioned above.
2. Create folder on your C: drive called CWM
3. Go to post "Eee Pad Transformer Android Development\[Recovery] Rogue XM Recovery v1.3.0 (CWM-based Recovery v5.0.2.7" thread - http://forum.xda-developers.com/showthread.php?t=1446019
and "save as..." cwm_recovery-5027_rogue_rburrow-tf101-r1.zip to C:\CWM
4. Highlight/select command below:
adb push cwm_recovery-5027_rogue_rburrow-tf101-r1.zip data/media
then right click on it and select "copy" - it will save you typing it later.
5. Boot Recovery on your Transformer and connect it to PC, let system install device drivers
6. Click START, "Run...", type: cmd
7. It should show you path to your profile folder - C:\Users\yourname>
8. Type: cd /CWM
it will change folder to C:\CWM>
9. type: adb devices
(it should give you your device ID, if it still will give "no device id" then there I can't help you - I'm sorry)
10. right click on black background and select "paste" (you'll see command that you've copied from number 4), then press enter
11. It should copy recovery onto your internal sdcard - you will be able to select it from tablet
12. type adb kill-server and disconnect tablet, install new recovery and from that one you will be able to select external or internal sdcard
Notes:
I don't know why but I was able to send only small file from CWM-adb connection, it kept disconnecting quite quickly that is why I recommend sending Rogue XM Recovery instead of whole new ROM.
Other thing - it may depend on what windows system you have - I'm on Win 7 x64 (don't remember how it worked on other versions) and I can paste onto cmd (black) window without problems from right click menu. If you won't be able to paste there or you'll get some rubbish, try to right click on top bar and select "Edit" and then "Paste".
Ok, that's all. Hope it will work.
thanks for all inputs. i did a full wipe but not as scripts. i wiped manually. i did try to reboot but stuck as eepad screen. will try to re-install asus drivers and uninstall htc ones. hopefully i get it done today. i will update later...
still no luck. device not found. im going to try to install new sdk... i hope it works. ive already removed htc sync and drivers. also re-installed asus sync and updated drivers. on device manager detects on other devices transformer but drivers are not installed.
yahoo! got it working now. i had to enable adb usb Drivers for Nvidia Tegra based Android Tablets and re-install SDK download android usb and learn What Is ADB And How To Install It With Android SDK.
finally got my tablet working again and my first thing to do is have a copy of a ROM and CWM in both storages!
thanks alot for the input and for helping!
thanks Kraliz
monespeso said:
yahoo! got it working now. i had to enable adb usb Drivers for Nvidia Tegra based Android Tablets and re-install SDK download android usb and learn What Is ADB And How To Install It With Android SDK.
finally got my tablet working again and my first thing to do is have a copy of a ROM and CWM in both storages!
thanks alot for the input and for helping!
thanks Kraliz
Click to expand...
Click to collapse
Could you tell me how to do that? Because I have the exact same problem.
My daughter's Nexus S touchscreen has died. It died slowly in that on the first few occasions she couild pop the battery and it would come back. Now it won't come back at all and is stuck on the pattern lock screen.
Before we send the phone for repair under warranty she is keen to get the photos off the phone since a repair might reset the phone. I was thinking we could mount the phone as a USB device but it doesn't show up perhaps because it won't until the pattern lock is entered else anybody could get data off your phone bypassing security.
Any other things we could try before giving up and hoping the repair doesn't delete all the data?
Thanks
Boot into recovery, make a nand then extract data through adb?
adb pull /sdcard/path-to-whatever
Can you explain the path to whatever? Like if I want it in folder "A" on the desktop.
Sent from my Galaxy Nexus using Tapatalk 2
Check this thread
http://forum.xda-developers.com/showthread.php?t=1573744
treUse said:
adb pull /sdcard/path-to-whatever
Click to expand...
Click to collapse
Out of interest I tried this on my GN. adb recognises the phone and adb devices shows the serial number. But adb pull /sdcard says invalid remote file. No idea what that means since using ES File Explorer sdcard is a valid directory on the phone (and I suppose it would also be on the Nexus S)
lchiu7 said:
Out of interest I tried this on my GN. adb recognises the phone and adb devices shows the serial number. But adb pull /sdcard says invalid remote file. No idea what that means since using ES File Explorer sdcard is a valid directory on the phone (and I suppose it would also be on the Nexus S)
Click to expand...
Click to collapse
ADB "thought" you meant to copy a file.
To copy the entire sdcard directory you should do something like this:
Code:
adb pull /sdcard/ sdcard/backup/on/pc/
The command parameters are "adb pull <source> <destination>"
Just make sure source ends with a /
Maybe a Windows based software?? Droid Explorer, very useful.. http://de.codeplex.com/ :good:
Well I finally got the phone to play with. The screen indeed dead. I installed the Google USB drivers from the SDK and also the Samsung drivers.
When I boot the phone into the recovery menu I can run fastboot devices and see the following
????0AC4B09900?? fastboot (of course the ? are not there but I wanted to anonmyuse the serial)
So far so good.
In device manager under Android Phone it show Samsung Android ADB Interface
But if I try adb devices I get nothing.
Forgot to mention my daughter said USB Debugging was turned off but I am not sure that makes any difference and anyway, we can't boot Android to turn it on
So I select Recovery and see the Android with the exclamation mark. Windows beeps to indicate that some sort of devices has been installed,
But in Device Manager no phone shows which explains why adb can't fidn the phone but not why.
I can bring up the recovery menu but still no adb
Any suggestions?
Thanks
Boot into Fastboot and flash CWM Recovery.
RL77LUC said:
Boot into Fastboot and flash CWM Recovery.
Click to expand...
Click to collapse
But it looks like I have to unlock the bootloader to do that and the phone is still under warranty so that would invalidate the warranty wouldn't it? She would like to get the data off the phone. A screen fix shouldn't zap the memory but you never know.
what this device installed CWM?? if installed cwm just bot it to cwm an goto mass storage
cukdus said:
what this device installed CWM?? if installed cwm just bot it to cwm an goto mass storage
Click to expand...
Click to collapse
The phone is stock
lchiu7 said:
The phone is stock
Click to expand...
Click to collapse
If you unlock the bootloader to flash CWM your memory will also be wiped, so you will loose all the photos you want to save, so don't do that.
Also if you have the USB debugging off, the ADB commands won't work. I'm afraid you're SOL, since you have the bootloader locked you can't flash a kernel with USB host, that would allow you to use a mouse to navigate in the phone and since you don't have USB debug you can't pull files from the "SDcard"... Better take it to the store and try to ask them if they can save the photos before they do anything to the phone, but i guess if it's a digitalizer problem, they won't mess with the NAND.
Check out http://www.moborobo.com/ and see if it works for you.
If you have root you have extended functionality, like control the device from the PC. But if i recall correctly, even without root you should be able to get your files.
**UPDATE**
NEW VERSION
THIS RELIES ON ADB COMMANDS, SO IF YOU DO NOT HAVE USB DEBUGGING TURNED ON, OR A CUSTOM RECOVERY TO BOOT TO, THEN IT WILL NOT BE AS SIMPLE AS JUST RUNING THE PROGRAM.
Another user was having issues because he had an emulator installed, so I updated the file to give you the choice between an emulator, or device. I intend to update further to allow you to check for and select an individual device, that will come soon..
----------------------------------------------------------------------------------------------------------------
Recently my Galaxy s2's screen smashed, and, after replacing it with a GS4, i realized that many of my pictures were stuck on the internal sd card of the GS2. Being unable to turn on mass storage mode, I made a very simple tool that makes using adb pull a simple, painless process, even for the most computer illiterate of android users. Hope this helps if anyone needs it.
For anyone having issues...
If you had not previously activated USB Debugging, there are several steps you need to follow in order to enable ADB
SCREEN WORKING TOUCH BROKEN NO CUSTOM RECOVERYfirst, if you can see your screen, and have access to an otg cable, plug a mouse in to the otg cable, and the otg cable into the phone. Use the mouse to enable USB debugging, or to transfer files.
HOW TO ENABLE USB DEBUGGING
SCREEN WORKING TOUCH BROKEN WITH CUSTOM RECOVERYboot to your custom recovery ADB commands will work here. (usually hold vol- + pwr)
HOW TO BOOT TO RECOVERY
Once in custom recovery, connect the device to the PC.
open CMD and enter the following commands;
cd c:\android (this is your ADB path, c:\android is default)
adb devices
The result should be something like
List of devices attached
051a4dd5 recovery
^^this number will be different for you
if you get a result on ADB devices, then you can use the program
SCREEN BROKEN TOUCH BROKEN WITH CUSTOM RECOVERYboot to your custom recovery ADB commands will work here. (usually hold vol- + pwr)
HOW TO BOOT TO RECOVERY
Once in custom recovery, connect the device to the PC.
open CMD and enter the following commands;
cd c:\android (this is your ADB path, c:\android is default)
adb devices
The result should be something like
List of devices attached
051a4dd5 recovery
^^this number will be different for you
if you get a result on ADB devices, then you can use the program
SCREEN BROKEN TOUCH BROKEN NO CUSTOM RECOVERYnow things get complicated...
*The following is paraphrased from this site
1. download the custom recovery image for your device. Copy the recovery image to a convenient location on your computer, preferably with a short path. We will be placing it on the C Drive directly (not in any folder) and using that in the next steps.
Note: The recovery image should have .img extension. If it is in a zip file, extract the .img file from it.
I recommend clockwork mod non touch from this page
2. Power your device off and reboot your device to FASTBOOT or DOWNLOAD MODE depending on which type of device you have.
(most devices are fastboot, SAMSUNG typically uses DOWNLOAD MODE)
how to boot to fastboot or download mode
[FASTBOOT]3. Connect your device to your computer via USB and wait till you see the PC recognize the device
to check if your device is in fastboot and connected use CMD and enter the following commands;
cd c:\android (this is your ADB path, c:\android is default)
fastboot devices
you will see a list of connected devices. if not, something went wrong.
4. Launch Command Prompt and type the following commands;
cd c:\android (this is your ADB path, c:\android is default)
fastboot flash recovery c:\recovery.img
5. Wait for the process to finish.
6. Turn device off then boot to your custom recovery ADB commands will work here. (usually hold vol- + pwr)
HOW TO BOOT TO RECOVERY
Once in custom recovery, connect the device to the PC.
open CMD and enter the following commands;
cd c:\android (this is your ADB path, c:\android is default)
adb devices
The result should be something like
List of devices attached
051a4dd5 recovery
^^this number will be different for you
if you get a result on ADB devices, then you can use the program
[RECOVERY MODE (SAMSUNG)]USE THE INSTRUCTIONS ON THIS PAGE
Once in custom recovery, connect the device to the PC.
open CMD and enter the following commands;
cd c:\android (this is your ADB path, c:\android is default)
adb devices
The result should be something like
List of devices attached
051a4dd5 recovery
^^this number will be different for you
if you get a result on ADB devices, then you can use the program
HOPEFULLY THIS HELPS. REMEMBER TO CHECK THE FORUM PAGE FOR YOUR DEVICE IF YOU RUN INTO ISSUES. THIS ISN'T ANYTHING THE MEMBERS OF XDA HAVEN'T DONE THOUSANDS OF TIMES OVER.
Don't forget to hit "Thanks"
i'll bump this thread for those who didn't see this amazing tool, this tool is really useful, thank you very much
Hi,
Sturggling to find the .adb file as my phone shows up as a "Portable Device" any ideas?
Cheers
Thank you!
I joined just to say thank you to FuzzyMeep Two. Thanks for an awesome tool! It worked better than advertised!
:good:
Thanks again!
-th3r3isnospoon
Question
Hi! Can I use that to restore data not from sdcard but from internal memory of the device? I was storing photos on device memory on my Asus TF300T and now its bricked. I need to restore these photos, my girlfriend has something like 1000 of them from her trip to Caracas. Its very important for her. I already managed to connect the device through fastboot and I launched anb in cmd. What should I do next? Please help me guys
koperkowy said:
Hi! Can I use that to restore data not from sdcard but from internal memory of the device? I was storing photos on device memory on my Asus TF300T and now its bricked. I need to restore these photos, my girlfriend has something like 1000 of them from her trip to Caracas. Its very important for her. I already managed to connect the device through fastboot and I launched anb in cmd. What should I do next? Please help me guys
Click to expand...
Click to collapse
Yes, when it references SD Card it means the internal "SD" storage built in to the phone, not the removable one. It should work as long as ADB can connect.
Sorry for taking so long to reply, i really hope you got your pictures back.
FuzzyMeep Two said:
Recently my Galaxy s2's screen smashed, and, after replacing it with a GS4, i realized that many of my pictures were stuck on the internal sd card of the GS2. Being unable to turn on mass storage mode, I made a very simple tool that makes using adb pull a simple, painless process, even for the most computer illiterate of android users. Hope this helps if anyone needs it.
P.S. I apologize if i have posted this in the wrong place, if so please let me know.
Click to expand...
Click to collapse
Really great stuff - so simple but so effective. Cheers and thanks.
Error msg
zobes said:
Really great stuff - so simple but so effective. Cheers and thanks.
Click to expand...
Click to collapse
When i run that tool, i get the error mesg: more than one device and emulator,
I dont want to uninstall the emulator coz it was a headache getting it running
How i procede to select the device to be used
alisdairjk said:
When i run that tool, i get the error mesg: more than one device and emulator,
I dont want to uninstall the emulator coz it was a headache getting it running
How i procede to select the device to be used
Click to expand...
Click to collapse
NEW VERSION
Try this, i haven't gotten to test it, so please let me know if it worked for you, I added the option of selecting an emulator or USB device, because of your post. Hopefully it helps.
When I try to run this I also get an error message saying that the adb.exe file cannot be found.
Please can anyone help?
Joeb29 said:
When I try to run this I also get an error message saying that the adb.exe file cannot be found.
Please can anyone help?
Click to expand...
Click to collapse
Have you also installed ADB, as well as this software?
I'm also having an issue - I have installed java, java SDK and ADB, so I can now run the data recovery tool. But when I do I'm getting "error:device not found" - am I missing drivers or something? I couldn't get all the way on the ADB configuration, because part of it required me to do something on the device... anyway, looks like the computer isn't recognising the the phone at the moment.
Any help very gratefully received (phone is Samsung Galaxy S2).
joffmeister said:
Have you also installed ADB, as well as this software?
I'm also having an issue - I have installed java, java SDK and ADB, so I can now run the data recovery tool. But when I do I'm getting "error:device not found" - am I missing drivers or something? I couldn't get all the way on the ADB configuration, because part of it required me to do something on the device... anyway, looks like the computer isn't recognising the the phone at the moment.
Any help very gratefully received (phone is Samsung Galaxy S2).
Click to expand...
Click to collapse
I have the same situation right now. Managed to make your program work then I get the "error:device not found". My phone does show up in the computer folder(albeit not in mass storage mode), but isn't that what this program was made to work around?
My phone is a LG Optimus G with a smashed glass... The LCD still displays fine, but I'm stuck at my swipe lock because the digitizer is dead.
Thank you for your help and your wonderful program.
Thanks for this app. My girlfriend broke her screen and digitizer on her Galaxy S4. She never turned USB Debugging mode and has a lock on her screen. When using your app I get the same error when I use adb by itself which is "error: closed". ADB detects my phone but any command I use in ADB or with your app I get that same error.
Do you know how to fix this? Thanks in advance.
Thanks a lot man.
dude this tool is just amazing and does exactly what it promised. I was spending sleepless nights thinking about how to recover my data from my broken galaxy nexus and now that I have it I can rest easy. Seriously can't thank you enough for this. Just joined xda to thank you buddy.:laugh::fingers-crossed:
Getting an error "The system cannot find the path specified."
I start the recovery tool, set eh adb path successfully, and then I get this error. If I try running the recovery to pull the DCIM library I get this:
"error: device not found"
What can I do?
Thanks!
Either way this is an amazing tool, seeing how it helped some people already. :good:
Hi, Seem to have the same problem as many others, Device not found. I cant change to MTP mode on my LG G2.
I hope someone can find a solution to this problem.
Program seems amazing doh.
Hello,
This is really a great tool ! I was wondering if you could add the possibility to recover the external sd card aswell.
Device not found
Tried to recover a Samsung Galaxy S3 mini with a broken screen
I installed adb and RecoverData, run it and then get a "device not found error"
What can I do?
Amazing app. thank you so much :good:
FuzzyMeep Two said:
**UPDATE**
NEW VERSION
Another user was having issues because he had an emulator installed, so I updated the file to give you the choice between an emulator, or device. I intend to update further to allow you to check for and select an individual device, that will come soon..
----------------------------------------------------------------------------------------------------------------
Recently my Galaxy s2's screen smashed, and, after replacing it with a GS4, i realized that many of my pictures were stuck on the internal sd card of the GS2. Being unable to turn on mass storage mode, I made a very simple tool that makes using adb pull a simple, painless process, even for the most computer illiterate of android users. Hope this helps if anyone needs it.
Don't forget to hit "Thanks"
Click to expand...
Click to collapse
Hi, Thank you very musch, It's so usefull for me.. :angel:
Hi everyone,
Since yesterday, my HTC One S is stuck in bootloop (even in safe mode), for unknown reasons (did not install an app, nor tried to flash a ROM or update version of something).
I'd just like to recover some pics I did not sync with Dropbox and a few files. What I have to do that is :
Win7 64 bits, HTC drivers installed
HBOOT-2.15.0000 UNLOCKED S-ON
FASTBOOT USB is shown when plugged to the PC (when I go in the recovery, my PC recognizes the device, otherwise it just shows as My HTC)
I tried using adb to "pull" some files. When I enter the command adb pull /system/ \system for example, it works, it transfers the files. But when I try with adb pull /internal_sd/ \card it says "remote object 'sdcard' doesn't exist", which is weird since I can see the different folders when using TWRP.
Any idea what might help?
Thanks!
Kumbo said:
Hi everyone,
Since yesterday, my HTC One S is stuck in bootloop (even in safe mode), for unknown reasons (did not install an app, nor tried to flash a ROM or update version of something).
I'd just like to recover some pics I did not sync with Dropbox and a few files. What I have to do that is :
Win7 64 bits, HTC drivers installed
HBOOT-2.15.0000 UNLOCKED S-ON
FASTBOOT USB is shown when plugged to the PC (when I go in the recovery, my PC recognizes the device, otherwise it just shows as My HTC)
I tried using adb to "pull" some files. When I enter the command adb pull /system/ \system for example, it works, it transfers the files. But when I try with adb pull /internal_sd/ \card it says "remote object 'sdcard' doesn't exist", which is weird since I can see the different folders when using TWRP.
Any idea what might help?
Thanks!
Click to expand...
Click to collapse
Mounting usb storage from recovery does not make the sdcard available on your pc?
Now reading again I saw you said about fastboot... Your phone is stock? That's not the recovery in this case, you're entering the bootloader
Try to mount it from TWRP, you said it's accessible from there
Sent from nowhere over the air...
Rapier said:
Mounting usb storage from recovery does not make the sdcard available on your pc?
Now reading again I saw you said about fastboot... Your phone is stock? That's not the recovery in this case, you're entering the bootloader
Try to mount it from TWRP, you said it's accessible from there
Click to expand...
Click to collapse
Thanks for your answer. You're right it was the bootloader, not the recovery.
I tried mounting and unmounting numerous times and it finally worked! I still could not see anything from Win7, but at least the adb pull command is working. I've been able to get the files I wanted, so I guess now I'll try to wipe everything I can and start fresh.
Next phone: one with a sdcard that I can plug out, and no important data on the internal memory! Less hassle.
Hello Helpers, I shattered my Nexus 4 screen, and the phone has a Pin lock, and is currently in Airplane Mode with BlueTooth enabled. It does Not have USB debugging enabled.
My objective is just to pull out the video, audio, and pictures files, after which I would throw the phone away. I appreciate any feedback, or if someone can help me post a reply to "k.janku1" at the post here http://forum.xda-developers.com/showthread.php?t=2786395 Please refer to point (4) below.
So is there a way I can enabled USB debugging or pull my files out? Following are what I have done, and none are successful in accessing the phone:
1) I have an OTG cable with a mouse. Nexus 4 would not recognize it. I did try to have this OTG Cable + Mouse plug into another Motorola phone and it worked, just not Nexus 4.
2) I plug my Nexus 4 into the PC through the USB cable, the Windows 10 recognize it but when I try to browse that Nexus 4, no files show up.
3) I installed the Android Studio 2.2.2, with various SDK (5.0 and 5.1 SDK) + Google USB driver. And then proceed to run the ADB "shell" or "devices" command located in folder "platform-tools", and the command line would tell me -- "error: no devices/emulators found", or "List of Devices attached" but with NO list of devices displayed. I even boot into Recovery Mode and the ADB command still not seeing any phone.
4) I even try the post here, and I could not get it working either -- http://forum.xda-developers.com/showthread.php?t=2786395
i) I tried the steps listed here http://forum.xda-developers.com/showpost.php?p=66731042&postcount=260 but it does not work for me. The step (2) here returned me "No devices", while step (3) is sort of confusing as it involves TWRP (??) and it said BootLoader would erase all my data files!
ii) Another post here in the same thread -- http://forum.xda-developers.com/showthread.php?p=62398797#post62398797 which mentions the use of "Flash through ADB". But then my phone does not have USB Debugging enabled, so how can ADB talk to the phone in the 1st place? And compile his codes in Android Studio perhaps?
iii) Another post of same thread -- http://forum.xda-developers.com/showthread.php?p=61792353#post61792353 which is lengthy and involves self-custom kernel + compile using Kernel Kitchen. Would this really work?
Thanks
Sean
I had the same of your situation i search and tried a lot of things even show the phone screen in pc but me too i didn't have usb debugging enabled, so what i did is :
Flash the stock ROM for my phone by Odin (it don't need usb Debugging enabled it is for Samsung phones) and by flashing new ROM all your files will be stay in the internal storage, after that the files will be showed in the PC, i don't know if u try that before so that is my solution
Sent from my GT-I9300 using Tapatalk
Xkirnel99 said:
...
Flash the stock ROM for my phone by Odin (it don't need usb Debugging enabled it is for Samsung phones) and by flashing new ROM all your files will be stay in the internal storage, after that the files will be showed in the PC, i don't know if u try that before so that is my solution
Click to expand...
Click to collapse
Thank you for the hint. But I doubt if this approach would work for Nexus 4. I searched online for Odin + Samsung, seems like Samsung phone has a Download mode where the phone would accept the new image file put to it. There is no such mode for Nexus 4, so the phone would not read anything in easy steps like Download mode.