Related
How to install clockworkmod recovery:
Click to expand...
Click to collapse
SP Flash Tool method, root not required
Click to expand...
Click to collapse
1. Download MTK6577 Drivers.zip and unzip/extract on your Windows PC, just run InstallDriver.exe to install drivers.
2. Download CWM Recovery v6.0.1.5 + scatter.zip and SP_Flash_Tool_v3.1220.02_FOR_S101A.zip , unzip/extract them.
3. Now open extracted SP Flash Tool folder and run Flash_tool.exe
4. Click on "Scatter-loading" button which is on the right side below Downloading Agent. A new window will open. Browse to the extracted CWM Recovery v6.0.1.5 + scatter folder and select MT6577_Android_scatter_emmc.txt file.
5. Flash tool will populate the Map file on the application window. You will see multiple entries. Uncheck all entries except for RECOVERY.
6. Now click on "Download". Warning message will occur, but ignore that and click Yes.
7. You will see in the status bar below "Searching", now connect your phone (with battery inserted + Press and Hold Volume Up Key) via the USB cable.
8. Wait for the process to finish and then you will get a window showing green circle.
Very Easy & safe way to FLASH CWM RECOVERY in any Android Device
steps:->
1. Downlaod CWM recovery.img
2: download recovery manager from HERE now Copy CWM recovery.img in SD card, now install the recovery manager.apk normally
3. Now open the recovery manager app you recently installed.
4. Click on recovery in app menu.
5. There click on install recovery
6. Then click on the recovery image name of ‘recovery.img’
7. Let the app install the recovery. after it done a message will show.
current recovery : unrecognized…. just ignore it.
That’s all now you have installed your recovery
Click to expand...
Click to collapse
Some SS Tutorials for how to flash CWMR using SP Flash Tools
Click to expand...
Click to collapse
Check here all steps
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Click to expand...
Click to collapse
Congrats You have flashed CWMR !
Note: If you get any error in SP Flash Tool, then recheck your MTK drivers installation or manually install them through device manager.
Booting into CWM recovery is the same as in the stock recovery. Switch on the phone with "Volume Up" and "Power" button Pressed. The Phone will boot into CWM!
I have also attached the the Stock Recovery.zip.
New & Latest Released CWMR 6.0.2.8 is now available for Micromax A89 Ported by ME
Click to expand...
Click to collapse
Here is The New Version of CWMR 6.0.2.8
Click to expand...
Click to collapse
Change Logs
Click to expand...
Click to collapse
Partition SD Card Option Added in Advance Menu
Install Zip From Sideload option added in Main menu
Backup & Restore Backup from Internal & Externel SD is now Available
Click to expand...
Click to collapse
Credit : -
bgcngm
yuweng
Cygwin
Me
dont say Thanks Hit
if you can
Click to expand...
Click to collapse
Sorry i dont have Installed DDMS in my newly formated PC thats why Take % Post Screenshots using My A90s
here are Proof this is working fine i personally Tested...
How to install clockworkmod recovery:
....
...
..
...
Credits goes to Cygwin Kitchen + ME
Click to expand...
Click to collapse
WTF! all you can shove your credit up your ass dude! although i am thankful to you but stealing someone else's credit isn't fair!
mujhe pata he ki ye indians ki gandi aadat he par yaar tum jese logo ke karan hi to hamari bejjezti hoti he.. sudhar jao!!
Click to expand...
Click to collapse
comeon dude! behave!
btw thanx! :laugh:
Your Welcome dude.............
I give credit Cygwin cuz i unpack stock recovery for system mount points thats why i give credits...........also i give credit to me cuz i port that Recovery for A89 Device lol............. btwn thanks for your Advice.....sudhar ne ki kosish jarur karenge.......
i am unable to install drivers...what should i do....i am using windows 8..
piyushverma said:
i am unable to install drivers...what should i do....i am using windows 8..
Click to expand...
Click to collapse
For Installing Driver just Run that exe file if you are in Win 8 then try this
Right Click on file and Run As Administer then finish instillation and Reboot PC then connect your device.....
it still does not work...can u make a flashable zip fr it??
piyushverma said:
it still does not work...can u make a flashable zip fr it??
Click to expand...
Click to collapse
Dude, that just means that drivers aren't compatible with Win8, just use your friends pc or other pc with xp/7, you can install TWRP which is touch friendly (same as cwm) here
its work
its work ..... thanx...
yes it worked on xp....thanx for help....:victory:
Hi Bhardik
I posted this news here. I ended up using one of your screenshots without your permission because I was in a hurry. I hope you have no problem with that. :cyclops: http://www.droidiser.com/2013/02/install-clokcworkmod-recovery-micromax-a89.html
Re: [[CWM]] ( Recovery v6.0.1.5 ) For Micromax A89
droidiser said:
Hi Bhardik
I posted this news here. I ended up using one of your screenshots without your permission because I was in a hurry. I hope you have no problem with that. :cyclops: http://www.droidiser.com/2013/02/install-clokcworkmod-recovery-micromax-a89.html
Click to expand...
Click to collapse
No need to ask me for permissions cuz here I am only try my best to help &provide something good or new to other memmbers ...its all right even u no need to ask me for my any work u post where u want I don't mind it any more
Sent from my A90 using xda premium
Micromax a89 CMW recovery problem
its not working in xp ............
and can u specify the time required for process to complete .....
The progression bar is not showing atleast 1% after the 10 min.......
can u make tke video of it.......
Must Reply I m in a very serrious problem m,,
You missed this step
BHARDIK said:
1. Download MTK6577 Drivers.zip and unzip/extract on your Windows PC, just run InstallDriver.exe to install drivers.
2. Download CWM Recovery v6.0.1.5 + scatter.zip and SP_Flash_Tool_v3.1220.02_FOR_S101A.zip , unzip/extract them.
3. Now open extracted SP Flash Tool folder and run Flash_tool.exe
4. Click on "Scatter-loading" button which is on the right side below Downloading Agent. A new window will open. Browse to the extracted CWM Recovery v6.0.1.5 + scatter folder and select MT6577_Android_scatter_emmc.txt file.
5. Flash tool will populate the Map file on the application window. You will see multiple entries. Uncheck all entries except for RECOVERY.
6. Now click on "Download". Warning message will occur, but ignore that and click Yes.
7. You will see in the status bar below "Searching", now connect your phone (with battery inserted + Press and Hold Volume Up Key) via the USB cable.
8. Wait for the process to finish and then you will get a window showing green circle.
Congrats You have flashed CWMR !
Note: If you get any error in SP Flash Tool, then recheck your MTK drivers installation or manually install them through device manager.
Booting into CWM recovery is the same as in the stock recovery. Switch on the phone with "Volume Up" and "Power" button Pressed. The Phone will boot into CWM!
I have also attached the the Stock Recovery.zip.
Click to expand...
Click to collapse
Click on Recovery and browse to the CWM_6.0.1.5_recovery file in the A89 CWM folder Please insert this line between 5th and 6th step. Name this step as 5.1
hafeezluqman said:
Click on Recovery and browse to the CWM_6.0.1.5_recovery file in the A89 CWM folder Please insert this line between 5th and 6th step. Name this step as 5.1
Click to expand...
Click to collapse
Check OP Post 1
Tutorials posted with ScreenShots
How to flash CWMR Using Sp Flash Tools
Hope now every user can understand better.........
Thanks
BR
Hardy Ahir
TheMaker01 said:
its not working in xp ............
and can u specify the time required for process to complete .....
The progression bar is not showing atleast 1% after the 10 min.......
can u make tke video of it.......
Must Reply I m in a very serrious problem m,,
Click to expand...
Click to collapse
Check OP post 1
there u see tutorials with screenshots its also working on Windows XP Sp2 and Win7 tested by me in both OS
Try and follow all steps again hope u done.........
Good Luck
Thanks a Lot to Bhardik
U r just Awesome !!!!!!!!!!!!!!!!!!!!!!!!!!!
And once Again Tankssssssssssssss A lottttttttttttttttttttt
if you are rooted , u can use this app (mobile uncle tools) in fone ,
https://play.google.com/store/apps/details?id=com.mobileuncle.toolbox&hl=en
to install any recovery u want , without need of a pc ..there is no need to undergo the complicated spflashtool method...
all thanks to the devs for coming up with cwm and twrp for this device
MTK uncle tools
mmxa110user said:
if you are rooted , u can use this app (mobile uncle tools) in fone ,
https://play.google.com/store/apps/details?id=com.mobileuncle.toolbox&hl=en
to install any recovery u want , without need of a pc ..there is no need to undergo the complicated spflashtool method...
all thanks to the devs for coming up with cwm and twrp for this device
Click to expand...
Click to collapse
U should know that the s/w that u recommended is not working in MICROMAX A 89 i.e (mobile uncle tools)
I m Telling u that bcoz i tried it by myself in my MICROMAX A89!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!http://forum.xda-developers.com/images/smilies/silly.gif
TheMaker01 said:
U should know that the s/w that u recommended is not working in MICROMAX A 89 i.e (mobile uncle tools)
I m Telling u that bcoz i tried it by myself in my MICROMAX A89!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!http://forum.xda-developers.com/images/smilies/silly.gif
Click to expand...
Click to collapse
yes u r right m. Uncle tools not working for me in my A89 /A90 and my A90S.... thats why i recommended sp flash tool methods its working fine without any problems......
Hardy
Sent from my A90 using xda premium
Hi,
XDA world....Another post by me for XOLO A500 users.
This post will help you to install Clockworkmod recovery on your xolo a500.
First and the foremost thing you need is a rooted device.If you haven't rooted your device please root it. Refer the following link on how to root your lava xolo a500.
http://forum.xda-developers.com/showthread.php?p=39358817
Now download the XOLO A500 CWM Toolkit from download link given in the last.
1.) Extract the rar file to a folder anywhere on your computer.
2.) Open the folder and press shift key and right click(holding down the shift key) anywhere on the blank space of the screen and select "Open Command window here".
3.) You will see a command prompt window on the screen.
4.) Now connect your device via usb cable and enable usb debugging(Settings->Development->USB Debugging )
5.) Now Download the Quick Boot App from play store & install it in your Mobile. Open that App & click on Bootloader option.
6.) After sometime your phone will get stuck at the logo. (don’t panic)
7.) Now type on the cmd window:
fastboot devices(press enter)
fastboot flash recovery recovery.img
Within a sec the process will get over & it will install the cwm recovery on you Xolo A500
So Enjoy, you have successfully installed CWM Recovery on your Xolo A500..
Now you can check whether your CWM is working or not:-
---Remove battery of your phone and reinsert.
---Press Power and Volume down key to boot into recovery mode.
Congrats, You have successfully installed Cwm 6 in your Lava A500
But there is a bug in this recovery that is not yet fixed. The bug is that when you boot your device into recovery mode the user language is Chinese...But not to worry...
Ignore the recovery mode...
Go to play store and download ROM Manager by clockworkmod.It has all the features which the recovery menu should be having.
1.) Open ROM Manager
2.) Go to Install Clockworkmod recovery.
3.) Scroll down to the last and you will see Device not listed option.Open it.
4.) A prompt will come.Press yes. And then choose option 3.x+ option.
And now you are ready to use your CWM Recovery on ROM Manager.
Problem with installing CWM
Hi
Problem with installing CWM on my XOLO A500. When I Click quickboot booloader option it shows up an android logo with text “DOWNLOADING.. PLEASE DONT TURN OFF THE TARGET”
and hangs. Please HELP ASAP. THANKS
dhruba.sarma said:
Hi
Problem with installing CWM on my XOLO A500. When I Click quickboot booloader option it shows up an android logo with text “DOWNLOADING.. PLEASE DONT TURN OFF THE TARGET”
and hangs. Please HELP ASAP. THANKS
Click to expand...
Click to collapse
I have clearly mentioned that when you press bootloader option
DOWNLOADING.. PLEASE DONT TURN OFF THE TARGET
Click to expand...
Click to collapse
will appear.
As soon as you see this screen just type on the cmd window:
fastboot devices(press enter)
fastboot flash recovery recovery.img
This will successfully install CWM recovery.
Remove battery of your phone and reinsert.
---Press Power and Volume down(Please donot press volume up button) key to boot into recovery mode.
I'm unable to open command window through pressing the "Shift key+Right click" . Do yu have any vedio tutorial. Help me,..
Answer to your question.
GauravBak said:
I'm unable to open command window through pressing the "Shift key+Right click" . Do yu have any vedio tutorial. Help me,..
Click to expand...
Click to collapse
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Hope it helped you.
If I helped Please Hit Thanks.
but when i type the word "fastboot devices" then press enter and after that i type "fastboot flash recovery recovery.img" and enter, it says waiting for device.. nothing happen,..!
I'm using windows-xp
same problem.. stuck at waiting for devices on the cmd prompt. My device is already connected to pc and usb debugging mode is on
HELP,...
Procedure TO Install NEW ROM on XOLO A500
GauravBak said:
Plz buddy give me a tutorial about how to flash a ROM in my XOLO A500, I have installed CWM+ROM Manager and have TBMk5 ROM.zip in my SD card, a picture tutorial is very helpful.
Click to expand...
Click to collapse
Procedure TO Install NEW ROM on XOLO A500
1 First go to Cwm recovery by pressing power+volume down (-) key
2 then wipe data/factory reset
3 wipe cache partition
4 go to "advanced"
5 & wipe dalvik cache & wipe battery stats
6 then go back
7 & select 2nd option install zip from sd card & locate the zip ,,,, then follow the procedure & u will get new rom installation by aroma installer
8 then reboot system & wait beacause initialisation takes few minutes ... enjoy!!! reboot is necessary
NOTE:- for selecting any option press power key & to scroll by volume keys
,, check sd card is mounted or not ,, if not mount by "mounts and storage" option
please hit thanks as it helped you..
for any query visit my account or just reply:good::good:
Recovery Mode not opening..
Hii..
I have installed cwm on my phone..
but now i am not able to open the recovery mode by pressing volume up+power..:crying::crying::crying:
i tried both volume up & down with Power key combination..!!
so plz help me n tell me how to get back my original recovery mode..!!
ThanXX a Lot In AdvAnce..!!
its in chinese dude
the recovery menu is in chinese ......pls help
thanks
I read and review this , thanks.
thanx alot for helping
problems while flashing cwm.. plz help
Ishan16 said:
Hi,
XDA world....Another post by me for XOLO A500 users.
This post will help you to install Clockworkmod recovery on your xolo a500.
First and the foremost thing you need is a rooted device.If you haven't rooted your device please root it. Refer the following link on how to root your lava xolo a500.
http://forum.xda-developers.com/showthread.php?p=39358817
Now download the XOLO A500 CWM Toolkit from download link given in the last.
1.) Extract the rar file to a folder anywhere on your computer.
2.) Open the folder and press shift key and right click(holding down the shift key) anywhere on the blank space of the screen and select "Open Command window here".
3.) You will see a command prompt window on the screen.
4.) Now connect your device via usb cable and enable usb debugging(Settings->Development->USB Debugging )
5.) Now Download the Quick Boot App from play store & install it in your Mobile. Open that App & click on Bootloader option.
6.) After sometime your phone will get stuck at the logo. (don’t panic)
7.) Now type on the cmd window:
fastboot devices(press enter)
fastboot flash recovery recovery.img
Within a sec the process will get over & it will install the cwm recovery on you Xolo A500
So Enjoy, you have successfully installed CWM Recovery on your Xolo A500..
Now you can check whether your CWM is working or not:-
---Remove battery of your phone and reinsert.
---Press Power and Volume down key to boot into recovery mode.
Congrats, You have successfully installed Cwm 6 in your Lava A500
But there is a bug in this recovery that is not yet fixed. The bug is that when you boot your device into recovery mode the user language is Chinese...But not to worry...
Ignore the recovery mode...
Go to play store and download ROM Manager by clockworkmod.It has all the features which the recovery menu should be having.
1.) Open ROM Manager
2.) Go to Install Clockworkmod recovery.
3.) Scroll down to the last and you will see Device not listed option.Open it.
4.) A prompt will come.Press yes. And then choose option 3.x+ option.
And now you are ready to use your CWM Recovery on ROM Manager.
Click to expand...
Click to collapse
the message showing on phone screen is "partition 'recovery' not support flash"...
plz tell how to fix it...
I have the perfectly working English cwm image
Sent from my A500 using XDA Premium 4 mobile app
same problem.. stuck at waiting for devices on the cmd prompt.
Ishan16 said:
I have clearly mentioned that when you press bootloader option will appear.
As soon as you see this screen just type on the cmd window:
fastboot devices(press enter)
fastboot flash recovery recovery.img
This will successfully install CWM recovery.
Remove battery of your phone and reinsert.
---Press Power and Volume down(Please donot press volume up button) key to boot into recovery mode.
Click to expand...
Click to collapse
What to do after pressing power + volume down button as further it is chineese menu.
Please reply
---------- Post added at 06:40 AM ---------- Previous post was at 06:04 AM ----------
Ishan16 said:
Hi,
XDA world....Another post by me for XOLO A500 users.
This post will help you to install Clockworkmod recovery on your xolo a500.
First and the foremost thing you need is a rooted device.If you haven't rooted your device please root it. Refer the following link on how to root your lava xolo a500.
http://forum.xda-developers.com/showthread.php?p=39358817
Now download the XOLO A500 CWM Toolkit from download link given in the last.
1.) Extract the rar file to a folder anywhere on your computer.
2.) Open the folder and press shift key and right click(holding down the shift key) anywhere on the blank space of the screen and select "Open Command window here".
3.) You will see a command prompt window on the screen.
4.) Now connect your device via usb cable and enable usb debugging(Settings->Development->USB Debugging )
5.) Now Download the Quick Boot App from play store & install it in your Mobile. Open that App & click on Bootloader option.
6.) After sometime your phone will get stuck at the logo. (don’t panic)
7.) Now type on the cmd window:
fastboot devices(press enter)
fastboot flash recovery recovery.img
Within a sec the process will get over & it will install the cwm recovery on you Xolo A500
So Enjoy, you have successfully installed CWM Recovery on your Xolo A500..
Now you can check whether your CWM is working or not:-
YOU JUST TELL ME HOW DO I GET MY ORIGINAL RECOVERY MENU BACK COZ IM GETTING VERY ANGRY NOW WITH THE CHINESE MENU. I DONT WANT ANY OTHER HELP.
PLEASE REPLY FAST.
---Remove battery of your phone and reinsert.
---Press Power and Volume down key to boot into recovery mode.
Congrats, You have successfully installed Cwm 6 in your Lava A500
But there is a bug in this recovery that is not yet fixed. The bug is that when you boot your device into recovery mode the user language is Chinese...But not to worry...
Ignore the recovery mode...
Go to play store and download ROM Manager by clockworkmod.It has all the features which the recovery menu should be having.
1.) Open ROM Manager
2.) Go to Install Clockworkmod recovery.
3.) Scroll down to the last and you will see Device not listed option.Open it.
4.) A prompt will come.Press yes. And then choose option 3.x+ option.
And now you are ready to use your CWM Recovery on ROM Manager.
Click to expand...
Click to collapse
JUST TELL ME HOW DO I GET MY NORMAL RECOVERY MENU BACK WITH ENGLISH COZ I AM VERY ANGRY NOW AND HATE THAT CHINESE MENU.REPLY FAST HOW TO GET RID OF THAT.
Sorry for the inconvenience caused.
Hey guys sorry for my late reply.
Those of you who are having problem in "Waiting for Device" please check that you have correctly installed adb drivers on your pc.
Still if you want you can try "Adb driver installer".
For the chinese menu issue please follow the below post by me.
http://forum.xda-developers.com/showthread.php?t=2349045
Press thanks if I helped.
Every thing went well still hadn't got CWM recovery
Ishan16 said:
Hi,
XDA world....Another post by me for XOLO A500 users.
This post will help you to install Clockworkmod recovery on your xolo a500.
First and the foremost thing you need is a rooted device.If you haven't rooted your device please root it. Refer the following link on how to root your lava xolo a500.
http://forum.xda-developers.com/showthread.php?p=39358817
Now download the XOLO A500 CWM Toolkit from download link given in the last.
1.) Extract the rar file to a folder anywhere on your computer.
2.) Open the folder and press shift key and right click(holding down the shift key) anywhere on the blank space of the screen and select "Open Command window here".
3.) You will see a command prompt window on the screen.
4.) Now connect your device via usb cable and enable usb debugging(Settings->Development->USB Debugging )
5.) Now Download the Quick Boot App from play store & install it in your Mobile. Open that App & click on Bootloader option.
6.) After sometime your phone will get stuck at the logo. (don’t panic)
7.) Now type on the cmd window:
fastboot devices(press enter)
fastboot flash recovery recovery.img
Within a sec the process will get over & it will install the cwm recovery on you Xolo A500
So Enjoy, you have successfully installed CWM Recovery on your Xolo A500..
Now you can check whether your CWM is working or not:-
---Remove battery of your phone and reinsert.
---Press Power and Volume down key to boot into recovery mode.
Congrats, You have successfully installed Cwm 6 in your Lava A500
But there is a bug in this recovery that is not yet fixed. The bug is that when you boot your device into recovery mode the user language is Chinese...But not to worry...
Ignore the recovery mode...
Go to play store and download ROM Manager by clockworkmod.It has all the features which the recovery menu should be having.
1.) Open ROM Manager
2.) Go to Install Clockworkmod recovery.
3.) Scroll down to the last and you will see Device not listed option.Open it.
4.) A prompt will come.Press yes. And then choose option 3.x+ option.
And now you are ready to use your CWM Recovery on ROM Manager.
Click to expand...
Click to collapse
Every thing went well even I saw Chinese recovery but now when I switch into recovery shows me android recovery instead of CWM recovery
For English recovery please follow the link given above your post.
Sent from my HTC Desire 310 dual sim
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Technical Specs
[*]Google it before posting here.
[*]Please post any guides and/or tutorials directly onto the forum, rather than links, otherwise this thread will be closed by the Moderator.
Click to expand...
Click to collapse
Rooting for 8GB Version
Procedure:
1. Download the Framaroot application and transfer it to SD card
2. Now go to Settings>Security and put check mark on Unknown Soruces
3. Now use file manager and browse to the location where you have placed Framaroot Application
4. Install it and open it. Now Select "Install SuperSU" and hit Boromir.
5. Now go to Play Store and search for Super User and install it after opening it might ask to update SU.bin, hit yes and then "Normal"
6. Reboot your Device.
[ROMs]
Please do not flash the firmware that is not meant for your phone. Flash only 4gb to 4gb and 8Gb to 8Gb
Auxus Nuclea N1 Stock Firmware
NEW
Final Version - 11-Dec-2013 - [Flash with SPFlash Tools]
Click to expand...
Click to collapse
OLD ROMs
Firmware Update (Intermediate V1) 18-Nov-/2013 [Flash with spflash Tools]
NucleaN1_FirmwareUpdate_V1_CWM.zip
Click Here - - [09/Sep/2013] [Flash with SPFlash Tools]
CWM Zip Download from herehttp://d-h.st/b3r
8GB version -
Click Here - [Flash with SPFlash Tools]
Custom ROMs
Click HERE
How to Flash Stock ROM using SP Flash Tools?
1) Unzip the ROM folder
2) Install the drivers and open SP Flash Tools..
Check the below post with images, if you are not sure whether drivers are installed or not.
If you face this problem, then try Firmware upgrade and connect the phone..
You can now safely disconnect your phone and turn it on. The process ends here.
FLASHING PATCH using SP Flash Tool(Single Files)
1)Select Android Scatter File .txt ....
2)Uncheck all files from the below box....
3)Select the correct file you want Flash by clicking it....
4)Click Download button on SP tool.... **"Dont click Firmware Upgrade"
5)A box asks to confirm it...Click Yes...
6)Connect Phone without the battery...
7)It will get Flashed...[/COLOR]
[Recovery]
1) Nuclea N1 Stock Recovery Click Here
2) TWRP Recovery- Click HereThanks to Kumar abhishek
3) CWMRecovery 6.0.3.3 Click Here or Click Here Thanks to C3C076
Procedure to Flash Recovery.
1) Download Mobile uncle tools from play store
2) Place the downloaded recovery.img in your sdcard
3) Open Mobile uncle tools
4) Select 'update recovery' and Click on the recovery.img
5) Reboot
adb method: For advance users:
---------------------------------------------------
Make sure you have all the drivers for your phone installed on your computer.
Make sure you have USB Debugging enabled, Install from Unknown Sources is enabled and device is detected in ADB run this command:
Code:
adb devices
Download the CWM Recovery
Press SHIFT key + Right mouse click in the folder where the file is located and select Open Command from Here.
Now, in the command prompt do the following:
a. Reboot into Bootloader mode. Use command:
Code:
adb reboot bootloader
b. Device will reboot and display logo. (check if device is in bootloader mode by running command:
Code:
fastboot devices
. If you see a device connected then you have successfully rebooted into fastboot mode.
c. Now, run this command:
Code:
fastboot flash recovery recovery.img
(This will flash the CWM recovery image to the device).
d. Once successful, reboot the device using this command:
Code:
fastboot reboot
.
How to Backup ur complete ROM
1. In CWM Recovery mode, select Backup and Restore
2. Select Backup
3. Wait till it finishes (May take upto 10 minutes)
How to restore ur backed up ROM from SD card
1. Go to CWM Recovery, select backup and restore
2. Select Restore
3. select the folder in date format (Folder name indicates the time and date when ur backup was created}
4. Wait till it finishes (May take upto 10-15 minutes)
Special Guides for Newbies to get Started
Everything you need to know about Clockworkmod Recovery
How to setup ADB and Fastboot properly
5 Things Every Android user should do
24 Apps Every Android User Must Install
5 Things to know before performing any Android tweak
Thanks to Driodiser
HIT THANKS PLEASE BECAUSE IT WONT COST ANY :angel:
Extend your storage on Nuclea N1
[Extend your storage on Nuclea N1] - Thanks to @kailashnj
Follow the instructions in the post HERE
How to enter into Recovery - Nuclea N1 :-
Code:
[LIST=1]
[*]Turn OFF your phone.
[*]Press & hold Vol(+) button and Power button for 12 seconds.
[B]Stock Recovery[/B]
[*]You will see a laid-down Android symbol with 'No command' message below it. Press the power button once.
[*]You will enter into menu 'Android System Recovery'
[*]Press Vol(-) to roll over options.
[*]Press Vol(+) button to select.
[*]DONE!
[/LIST]
Another options if you are facing trouble going to recovery:
Code:
1. Install Mobile Uncle tool
2. Reboot recovery.
MTK6589 Drivers
Universal Pdanet drivers Click Here
Follow this guide Here
Tools
MTK Android PC Sync Tool V2.1233.1 Click Here
SN_Write_tool_exe_v2.1132.0.rar - 8.27 MB
Guide Here
Driver_Auto_Installer_v1.1236.00 Click here
Meta-Mode is very useful if device fails to get detected by PC under normal Conditions.....To make device fall to Meta-Mode,just do these :
1) Start SP Tool on PC..
2) Now run SP Tool with "Firmware Upgrade/Download"
3) Switch OFF Phone..
4) Remove Battery..
5) Connect mobile to PC while holding Volume + button [WITHOUT BATTERY]..
6) Flashing will be started
7) Hold the button till flashing completes...
After 100% Flash,Release Button..
9) Insert Battery..
10) Start Device.
Click to expand...
Click to collapse
How to dump stock recovery image using SP Flash Tool
1) Download and install USB VCOM Driver
2) Download, extract and launch SP Flash Tool
3) Use "Scatter-loading" button to load attached scatter file: MT6589_Android_scatter_emmc.txt
4) Download stock recovery image and place inside the ROM folder. Then select only RECOVERY.
5) Turn off your phone. Make sure USB cable is unplugged. Wait until vibrator indicates it's turned off
6) Click Download button in SP Flash tool, confirm warning complaining about not all files being selected
7) Connect your phone and wait for the flash process to finish (indicated by window with green circle)
8) Unplug USB cable. Hold down Volume+ while turning your phone on to boot into recovery
Click to expand...
Click to collapse
Backing up your IMEI
Different Methods are available for this.
1) Use any RootExplorer to copy file /data/nvram/md/NVRAM/NVD_IMEI/MPOB_001 to your external SD card. (or if that folder does not exists, try /nvram/md/NVRAM/NVD_IMEI/MPOB_001). It is good to backup the entire folder /data/nvram/md/NVRAM.
2) Back up using Mobile Uncle utility. Click on Mobileuncle Tools --> Click IMEI Backup Restore (MTK) --> Backup/Restore
Restore your IMEI
Code:
1- Open Mobile Uncle Tools.
2- Goto Engineer Mode
3- Select Engineer mode[MTK]
4- Under Connectivity Tab go to CDS information
5- Select Radio Information
6- Select Phone1 (for the first imei)
7- at the top there is a command line which begins “AT+” just type there “AT +EGMR=1,7,”IMEI_1? (instead of IMEI_1 put your first imei number)
8- hit send command
9- You will / may get a confirmation that "sent to mSend".
10-Now come back and select “Phone2?
11-at the top there is a command line which begins “AT+” just type there “AT +EGMR=1,10,”IMEI_2? (instead of IMEI_2 put your second imei number)
12-Then just reboot the phone.
13- Dial ” *#06#” to Check Imei.
Factory ROM Backup for MT65xx via MTK Droid Root & Tools For BackUp & Unbrick
It's tested and working...
How to install ADB USB driver in window 7
use this method also in window xp,if any driver not install
Google USB Driver Rev 7 ( ADB driver )
inside three dll file driver
1-WdfCoInstaller01009.dll
2-winusbcoinstaller2.dll
3-WUDFUpdate_01009.dll
link
Click Here
Before use it is necessary to check that:
adb drivers are installed. Check device manager--> unknown devices. ADB Drivers attached.
Now the Tool
Credits: umesh gaba
[MOD][4.1 4.2] Extend Phone Storage 1.5, 2.5GB A116 (Other MT6589 Devices on request)
[Solution] NVRAM WARNING: Err = 0x10
Download this zip Click Here
Prerequisites:
You have to backup IMEI of your phone (both sim slot).
Step 1 - Extract the WiFi Fix files and place them in a folder on your memory card
Step 2 - Open Root Explorer
Step 3 - Click on Mount R/W
Step 4 - Click on data
Step 5 - Scroll down to the folder named nvram
Step 6 - Open APCFG folder
Step 7 - Open APRDEB folder
Step 8 - Delete the WIFI and WIFI_CUSTOM files
Step 9 - Now copy/move the files on your sdcard to data/nvram/APCFG/APRDEB and Paste
Step 10 - After pasting both the files, close Root Explorer and REBOOT your phone.
Here is another method Click Here
The bad news is.
Vijay have u bot the mobile..
Sent from my AUXUS Nuclea N1 using xda app-developers app
can you provide a review of the phone?
akashavel said:
Vijay have u bot the mobile..
Sent from my AUXUS Nuclea N1 using xda app-developers app
Click to expand...
Click to collapse
Hello dude,
i have booked this phone, and i am seriously waiting for some reviews.
It would be great if there was a video review done by you on you tube or where ever you are comfy.
The specs are awesome but there are some negative opinions as well.
This would help.
Thanks
akashavel said:
Vijay have u bot the mobile..
Sent from my AUXUS Nuclea N1 using xda app-developers app
Click to expand...
Click to collapse
Yes, I am in batch II.
dhavalg said:
Hello dude,
i have booked this phone, and i am seriously waiting for some reviews.
It would be great if there was a video review done by you on you tube or where ever you are comfy.
The specs are awesome but there are some negative opinions as well.
This would help.
Thanks
Click to expand...
Click to collapse
videos posted by me..
https://www.youtube.com/user/akashavel/videos
also chk this fb page
https://www.facebook.com/groups/Ibe...39765010250/?ref=notif¬if_t=group_activity
Hi Guys,
Even I have bought this phone and awaiting delivery, I was promised by 4th Aug. Lets see. The specs of this phone seems to be great other than the 4GB storage. I hope that apps2sd works really fine and I am able to store all my game data on the SD card. Wanted to know more info of this phone and the rom.
Regards,
Kailash
can't decide what to buy
is the costumer service good...i am really thinking to buy this phone but this brand was never heard before by me.....
in ur opinion which phone would be better
1. canvas 4 (micromax)
2. auxus nuclea n1 (iberry)
3. Xolo play (XOLO)
Thanks...
akashavel said:
videos posted by me..
https://www.youtube.com/user/akashavel/videos
also chk this fb page
https://www.facebook.com/groups/Ibe...39765010250/?ref=notif¬if_t=group_activity
Click to expand...
Click to collapse
That was really helpful, but i hoped some words about the phone from your mouth as well.
Need some comparison too,
But any ways it was awesome....I am going to continue with my order, actually i was planning on cancelling it. But now not...
Thanks for the videos.
Hope we get roms for it as well.
:victory: Yesss... XDA Thread for Auxus Nuclea.. feeling exciting.. Best Wishes, Guy.. :good::good:
dhavalg said:
That was really helpful, but i hoped some words about the phone from your mouth as well.
Need some comparison too,
But any ways it was awesome....I am going to continue with my order, actually i was planning on cancelling it. But now not...
Thanks for the videos.
Hope we get roms for it as well.
Click to expand...
Click to collapse
only thing is RAM so many apps consumes more memory .waiting for tweaked ROM.other than that the phone is gud..
I prefer to use Titanium Backup to freeze unwanted app rather to uninstall.. this app will save lots of RAM..
without source kernals cant we install custom Roms or stock roms, iam newbie to these things, i have a doubt, i have seen so many custom ROMs for samsung devices that means have samsung provided the source kernals???? please reply any experts
Without kernel source who would buy this phone and on top of that its Chinese brand better buy micromax Indian brand.....
ashok20205 said:
without source kernals cant we install custom Roms or stock roms, iam newbie to these things, i have a doubt, i have seen so many custom ROMs for samsung devices that means have samsung provided the source kernals???? please reply any experts
Click to expand...
Click to collapse
Yes, We can install Custom ROMs (Themed ROMs or Ported ROMs). But, with kernel sources a lot of development can happen. :good:
akashavel said:
only thing is RAM so many apps consumes more memory .waiting for tweaked ROM.other than that the phone is gud..
Click to expand...
Click to collapse
No need to wait for a Custom ROM. You can try One-Power-guard app, Clean master and Greenify app's.
Chris s5830i said:
Without kernel source who would buy this phone and on top of that its Chinese brand better buy micromax Indian brand.....
Click to expand...
Click to collapse
This mobile is good at it price with the spec's. Even Micromax is not providing kernel sources. Also, compared to the support of Micromax, iBerry is doing best.
abhiek bist said:
is the costumer service good...i am really thinking to buy this phone but this brand was never heard before by me.....
in ur opinion which phone would be better
1. canvas 4 (micromax)
2. auxus nuclea n1 (iberry)
3. Xolo play (XOLO)
Click to expand...
Click to collapse
Check the facebook page. Then you can decide
Can you post link for CWM for nuclea N1
can you help me with the link for CWM
Hello friends!
This is thread about Rooting and Installing CWMR (ClockWorkMod Recovery) in any MTK (MediaTek) device.
NOTE: REMEMBER TO MAKE NANDROID BACKUP BEFORE DOING ANYTHING!
AND I AM NOT RESPONSIBLE FOR ANY DAMAGE YOU DO TO YOUR DEVICE!
Just follow steps below:
Requirements:
1. MTK VCOM Drivers (Link: Click to download!)
2. SRS-Tool (Link: Click to download!)
3. MTKDroidTools (Link: Click to download!)
Password: awaisking
Before any thing else:
1. Connect Phone with PC
2. Install MTK VCOM Drivers
3. Enable USB Debugging in Phone (Steps below):
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Installing CWMR (ClockWorkMod Recovery) in MTK (MediaTek) Smart Phone:
NOTE 1: Make a backup through MTKDroidTool before, if something goes wrong!
NOTE 2: Your phone must be rooted before installing ClockWorkMod Recovery!
1. Extract and open MTKDroidTools and press ROOT button
2. Select root, backup, recovery tab and select To use boot from phone option,
then press Recovery and Boot button
3. Press Yes button when asked for Automatic CWM Recovery
4. Press No button when asked for Flash Patched BOOT.IMG
5. Press Yes button when asked for Install created recovery to phone
6. [THIS IS OPTIONAL] To check if recovery works press Yes button when asked for Reload phone in recovery
Here are 2 recovery screen shots:
PASSWORD?
DUDE!!
All your archives are password protected?
Kingston1 said:
Hello friends!
This is thread about Rooting and Installing CWMR (ClockWorkMod Recovery) in any MTK (MediaTek) device.
Just follow steps below:
Requirements:
1. MTK VCOM Drivers (Link: Click to download!)
2. SRS-Tool (Link: Click to download!)
3. MTKDroidTools (Link: Click to download!)
Before any thing else:
1. Connect Phone with PC
2. Install MTK VCOM Drivers
3. Enable USB Debugging in Phone (Steps below):
Installing CWMR (ClockWorkMod Recovery) in MTK (MediaTek) Smart Phone:
NOTE 1: Make a backup through MTKDroidTool before, if something goes wrong!
NOTE 2: Your phone must be rooted before installing ClockWorkMod Recovery!
1. Extract and open MTKDroidTools and press ROOT button
2. Select root, backup, recovery tab and select To use boot from phone option,
then press Recovery and Boot button
3. Press Yes button when asked for Automatic CWM Recovery
4. Press No button when asked for Flash Patched BOOT.IMG
5. Press Yes button when asked for Install created recovery to phone
6. [THIS IS OPTIONAL] To check if recovery works press Yes button when asked for Reload phone in recovery
Here are 2 recovery screen shots:
Click to expand...
Click to collapse
:thumbup:
Sent from Huawei U9508 EMUI 1.6,Andriod 4.2.2 Sorex B705 Rom
overlooked password
Disease8 said:
DUDE!!
All your archives are password protected?
Click to expand...
Click to collapse
The password is: awaisking
password please
Please share password bro
srikar nvvs said:
Please share password bro
Click to expand...
Click to collapse
Bro, password is awaisking
Kingston1 said:
Bro, password is awaisking
Click to expand...
Click to collapse
THANK YOU for this! the factory Android Recovery was pure crap lol for my clone'd iphone 5c which seems to be a slight clone'd Goophone.
WAIDroid said:
THANK YOU for this! the factory Android Recovery was pure crap lol for my clone'd iphone 5c which seems to be a slight clone'd Goophone.
Click to expand...
Click to collapse
Welcome!
Yep, both iPhone 5c and Goophone i5 N2 looks similar, both have MediaTek 6577 chipset.
i have the problem i was trying but when is created the CWM recovery it says recovery dosnt suit this phone.
i have mtk 6572 amr v7 1300mhz mali 400 etc
brand is sumvier aka in croatia h18 fresh 3g
Nice thread,helpful for creation of CWM in many mtk based devices.:good:
lacko123 said:
i have the problem i was trying but when is created the CWM recovery it says recovery dosnt suit this phone.
i have mtk 6572 amr v7 1300mhz mali 400 etc
brand is sumvier aka in croatia h18 fresh 3g
Click to expand...
Click to collapse
Try making recovery.img and boot.img backup through SP-FlashTool, then use MtkDroidTool to patch both imgs.
1: Open MtkDroidTool, connect your phone, click on Blocks Map button.
2: Write down 9th and 10th (9th=bootimg, 10th=recovery) row's Scatter and Size and click on Create scatter file button.
3: Open SPFT, click on Scatter-loading button and select that scatter file.
4: Click on Read Back tab, then click on Add button, then double-click on added item in listbox.
5: Set filename to boot.img, then change Start address to 0x(9th-row's-scatter/bootimg's-scatter) and Length to 0x(9th-row's-size/bootimg's-size).
6: Repeat 4th step, but this time set filename to recovery.img, then change Start address and Length as recovery's scatter and recovery's size.
7: Unplug phone from PC and remove and re-insert battery in phone (don't start phone)
8: Click on Read back button in SPFT, then plug in usb in phone.
9: After read back is done, take out cable then open MtkDroidTool, then select root, backup, recovery tab.
10: Tick To choose the boot.img file and click Recovery and Boot button, then select boot.img and recovery.img.
11: Copy scatter file and open MtkDroidTools folder, go to recovery and paste it there, then rename *_boot_patched_*.img and *_recovery_patched_*.img to boot.img and recovery.img.
12: Open SPFT and then select scatter file in recovery folder and flash boot and recovery.
Atrvscet said:
Nice thread,helpful for creation of CWM in many mtk based devices.:good:
Click to expand...
Click to collapse
Thank you
hi i have a problem. backup passive and and cant see 'to use from phone' How do I get backup ?
qwert00 said:
hi i have a problem. backup passive and and cant see 'to use from phone' How do I get backup ?
Click to expand...
Click to collapse
Hello,
First thing is your phone is Samsung Galaxy S4 (GT-I9502)
Second YELLOW light indicates that your phone is ROOTED but not permitted to MTKDroidTools.
'to use from phone' and 'backup' options only available when you grant permissions to MtkDroidTools by clicking on ROOT button (at bottom-right)
first use Backup to backup data from phone, then 'to use from phone' will be available for use.
or read this if ROOT button works:
http://forum.xda-developers.com/showpost.php?p=44509214&postcount=407
if ROOT button doesn't work then read this:
http://forum.xda-developers.com/showpost.php?p=38337401&postcount=5
Hi, this is will working for mtk6572w device?
yuvalg72 said:
Hi, this is will working for mtk6572w device?
Click to expand...
Click to collapse
Hello yuvalg72,
I think yes, because here: http://forum.xda-developers.com/showthread.php?t=2507515
in the #2nd post he was able to create backup with MTKDroidTools.
You can contact rua1 for more information.
Hi
I pressed yes in this message. What should I do?
ClusteredXC said:
I pressed yes in this message. What should I do?
Click to expand...
Click to collapse
Try going to recovery mode, if you are able to go in recovery mode, then there's ok.
other wise boot should be bricked, you have to find backup or flash files (or only boot.img) for your device!
Will It Really Work
any method for twrp
sir, I'm having an mtk device Lenovo a1000t has chip set mt8317t based on mt6577t we already have twrp 2.5 but I need method to compile or install tarp 2.6
BTW: thanks and cwm can be installed and working fine on my device
N'ayam Amarsh'e said:
Hi,
I really liked your guide but would like to ask you 'Will it work on my Spice Mi-492 ?' and also 'Can this recovery brick my phone ?' Please Reply Fast..
Click to expand...
Click to collapse
Thank you for liking.
First thing is make recovery.img and boot.img backup through SP Flash Tool, then you should try flashing cwm patched recovery.
vig vanx said:
sir, I'm having an mtk device Lenovo a1000t has chip set mt8317t based on mt6577t we already have twrp 2.5 but I need method to compile or install tarp 2.6
BTW: thanks and cwm can be installed and working fine on my device
Click to expand...
Click to collapse
Vig vanx, I am sorry, I never compiled ROM or Recovery,
but I think you should see these:
Official Port Tool: http://forum.xda-developers.com/showthread.php?t=1825722
Increase recovery partition to 7MB (yuweng): https://www.mediafire.com/view/?7humxw5eb99404u
TWRP: Porting TWRP to more devices: http://teamw.in/blog/17
or search on Google: https://www.google.com/search?q=twrp+mtk6577
Micromax canvas doodle 3 a.k.a A102 was released recently, a budget android phone or phablet. With a Meditek MT6572 processor and Android 4.2.2 stock.
Development thread for a local market phone exists rarely, and that rare thread is created by me[emoji15] .
Prime
Rooting Micromax Canvas Doodle 3 A102 with 1GB RAM Kitkat 4.4.2
Download recovery.img
You Need SP_Flash_Tool_v5.1352.01.zip
and UPDATE-SuperSU-v2.02.zip
Download below
put UPDATE-SuperSU-v2.02.zip in your SD Card
Now extract Sp Flash Tools and download Scatter File from Below
1. Open Sp Flash Tools
2. Put Scatter file and recovery.img in same folder
3. Load Scatter File Downloaded from below
4. now the recovery will be automatically selected
5. Install Drivers from here micromaxinfo.com/download.ashx?section=mobile-A102&file=Canvas_Doodle_3_Driver.zip
6. Switch off your Phone Pull out Battery and Connect it to PC using USB Cable
7. Click on Download
8. After the process is completed a green tick will appear
9. Now disconnect mobile and Put battery in and goto recovery mode using volume up+Power button select recovery and then push vol Down button
here is your custom recovery now select install zip from sdcard using power up and down buttons and select from power button
Now a prompt will appear select yes.
Now go back using soft keys on your mobile and reboot ..
Here you are
Your Phone is Rooted Now..
Kindly find the images of SP Flash & the flashed recovery.
It's for reference and guide.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
thanxxxxxxxx
was very helpfull ,,,,doodle 3 kitkat version root.......................try it,,,, its work for kitkat ota
Rooting Micromax canvas Doodle 3 .....
Friends if anyone is getting difficulty in going to recovery mode using Power+Volume up button
Download adb setup zip file from below and install the adb setup
then
goto Command Prompt and type
adb reboot recovery
your phone will goto recovery mode automatically
then rest is given in above post.
dont forget to ht thanks if helped.
Finaly root
navi95295 said:
Download recovery.img
You Need SP_Flash_Tool_v5.1352.01.zip
and UPDATE-SuperSU-v2.02.zip
Download below
put UPDATE-SuperSU-v2.02.zip in your SD Card
Now extract Sp Flash Tools and download Scatter File from Below
1. Open Sp Flash Tools
2. Put Scatter file and recovery.img in same folder
3. Load Scatter File Downloaded from below
4. now the recovery will be automatically selected
5. Install Drivers from here micromaxinfo.com/download.ashx?section=mobile-A102&file=Canvas_Doodle_3_Driver.zip
6. Switch off your Phone Pull out Battery and Connect it to PC using USB Cable
7. Click on Download
8. After the process is completed a green tick will appear
9. Now disconnect mobile and Put battery in and goto recovery mode using volume up+Power button select recovery and then push vol Down button
here is your custom recovery now select install zip from sdcard using power up and down buttons and select from power button
Now a prompt will appear select yes.
Now go back using soft keys on your mobile and reboot ..
Here you are
Your Phone is Rooted Now..
Click to expand...
Click to collapse
thanks bro,
finaly root my doodle 3 updated kitkat 1gb ram
i use below attached scatter file
MIUI ROM for Micromx Canvas A102
Here it Comes
MIUI ROM for Micromax Canvas Doodle 3 with 1GB ram
IS NO MORE WORKING
navi95295 said:
Download recovery.img
You Need SP_Flash_Tool_v5.1352.01.zip
and UPDATE-SuperSU-v2.02.zip
Download below
put UPDATE-SuperSU-v2.02.zip in your SD Card
Now extract Sp Flash Tools and download Scatter File from Below
1. Open Sp Flash Tools
2. Put Scatter file and recovery.img in same folder
3. Load Scatter File Downloaded from below
4. now the recovery will be automatically selected
5. Install Drivers from here micromaxinfo.com/download.ashx?section=mobile-A102&file=Canvas_Doodle_3_Driver.zip
6. Switch off your Phone Pull out Battery and Connect it to PC using USB Cable
7. Click on Download
8. After the process is completed a green tick will appear
9. Now disconnect mobile and Put battery in and goto recovery mode using volume up+Power button select recovery and then push vol Down button
here is your custom recovery now select install zip from sdcard using power up and down buttons and select from power button
Now a prompt will appear select yes.
Now go back using soft keys on your mobile and reboot ..
Here you are
Your Phone is Rooted Now..
Click to expand...
Click to collapse
this method is not working the flash app is not detecting my device .....its getting very annoying...cus I have been trying hard to root this phone with this version of OS...pls help me by making a video tutorial for rooting this phone
navi95295 said:
Download recovery.img
You Need SP_Flash_Tool_v5.1352.01.zip
and UPDATE-SuperSU-v2.02.zip
Download below
put UPDATE-SuperSU-v2.02.zip in your SD Card
Now extract Sp Flash Tools and download Scatter File from Below
1. Open Sp Flash Tools
2. Put Scatter file and recovery.img in same folder
3. Load Scatter File Downloaded from below
4. now the recovery will be automatically selected
5. Install Drivers from here micromaxinfo.com/download.ashx?section=mobile-A102&file=Canvas_Doodle_3_Driver.zip
6. Switch off your Phone Pull out Battery and Connect it to PC using USB Cable
7. Click on Download
8. After the process is completed a green tick will appear
9. Now disconnect mobile and Put battery in and goto recovery mode using volume up+Power button select recovery and then push vol Down button
here is your custom recovery now select install zip from sdcard using power up and down buttons and select from power button
Now a prompt will appear select yes.
Now go back using soft keys on your mobile and reboot ..
Here you are
Your Phone is Rooted Now..
Click to expand...
Click to collapse
your above steps are not working in my phone a102 ,doodle 3...i had recently upgarded to kitkat 4.4.2 .......none of the methods or rootapps are working for rooting this device
pls sir can you make one video tutorial for rooting this device with the above version of OS...asap
Rooting Micromax canvas Doodle 3 .....
damianlepcha said:
this method is not working the flash app is not detecting my device .....its getting very annoying...cus I have been trying hard to root this phone with this version of OS...pls help me by making a video tutorial for rooting this phone
Click to expand...
Click to collapse
Use following Link to Download the latest version of SP flash Tools and retry with the scatter file and recovery image given.
This will let you download recovery to your handset and getting Root.
copy and paste this link to your browser and download .. d-h.st/weue
couldn't reboot into recovery mode from doodle 3
My ram is 1 GB and my phone is rooted but I couldn't reboot into recovery plz anyone help meme
My PC is damaged plzzz anyone post a process to install CWM without PC
Thanks in Advance
Tapan Arya said:
My ram is 1 GB and my phone is rooted but I couldn't reboot into recovery plz anyone help meme
My PC is damaged plzzz anyone post a process to install CWM without PC
Thanks in Advance
Click to expand...
Click to collapse
Use Mobileuncle tools or Rebooter app for reboot into recovery mode.
I already used but doesn't works
Tapan Arya said:
I already used but doesn't works
Click to expand...
Click to collapse
If you are rooted then have u installed the CWM provided in Post #2
install using Mobileuncle tools
then root
Dont Forget to Endale USB Debugging mode from developer options
and reboot to recovery from mobile uncle tools.
It should reboot into recovery. if not then tell me what any error is coming ??
Error is that when I reboots into recovery micromax logo comes for 10 seconds and after that it restarts
Tapan Arya said:
Error is that when I reboots into recovery micromax logo comes for 10 seconds and after that it restarts
Click to expand...
Click to collapse
Just try to reinstall the recovery using mobileuncle tools and then reboot.
Hope it will work
I just tried to and updated recovery from mobile uncle but it shows as before
Please Help apk
Please someone attach me the stock camera app (and gallery), I've accidentally deleted it. My phone is doodle 3 A102 and is running 4.4.2 kitkat.
osamaanjum said:
Please someone attach me the stock camera app (and gallery), I've accidentally deleted it. My phone is doodle 3 A102 and is running 4.4.2 kitkat.
Click to expand...
Click to collapse
just copy and paste them in /system/app and change permissions to rw- r-- r-- and reboot
and for camera just restore factory settings if it didnt helped then reflash the stock Rom (System Only) and done.
Dont forget to backup your IMEI before doing anything.
osamaanjum said:
Please someone attach me the stock camera app (and gallery), I've accidentally deleted it. My phone is doodle 3 A102 and is running 4.4.2 kitkat.
Click to expand...
Click to collapse
Use ESfile Explorer to Copy it to system folder and change permissions..