I installed a kernel and forgot to whipe, now the xoom gets stuck at the rom logo and wont go any further. I have tried to get back to the clockwork mod settings but none of the button combinations work, the up button gives me starting RSD protocol Support, down gives me starting fastboot protocol support, both buttons gives me powering on bp.........Never ran into this problem before so was wondering if you guys had any advice or experience with similar issue.
AW: [Q] 3g xoom reboot problem
Reboot your device by holding volume up + power.
Then 3 seconds after you see the Motorola logo, hit volume down. You should now see "Android Recovery" in the top left corner. Hit volume up to boot into recovery.
Sent from my MZ601 using xda app-developers app
Related
I seemed to have bricked my Nexus S 4g, I unlocked the bootloader, and had MIUI running on there for some time with no problems, I took the rom off and started to run with just stock android. I ran into an issue when i tried to use an application that would change the system fonts, Fontchanger, and now the phone will not even reach the nexus s loading screen but instead gets immediately stuck at the first image screen showing the Google logo. When i hold the volume up and power button i can get into the boot menu, but when i try to get into the recovery menu i just get the triangle with the exclamation mark logo. Can anyone help me out with this one?
BUMP BUMP BUMP BUMP In a similar situation, flashed the wrong rom ran the OTA and wiped out recovery & USB.
Press Power and Volume Up Button in recovery mode and you will get options to clean things up. Did the same in morning and got it when accidentally pressed.
Ok so today my triumph stopped responding so i restarted it (took out the battery). then rebooted. upon reboot phone shuts down and now will hang at the motorola logo for about 10 min before boots but will shut back down due to the battery being dead(but had full charge when this started). Dont know what happened. So i try to get into clockworkmod to flash backup. cant get into it. the only thing i can do is get to the recovery.img file(pressing power+volume down). Other than that nothing.
also tried to boot with power pluged in. it stayed on but would not respond to any touches or button press except the lock button.
I have cwm 5.0.2.6 installed and tickerguy's cm7.
never had this problem till today. Any help would be appreciated.
a new development has occurred. now when i try to access recovery, the phone will just vibrate without stopping.
and i believe its stuck in a boot loop but without recovery i dont know anyway to exit the loop.
Are you able to get into download mode (power off then simultaneously press power button & vol- (should show polling))
Sent from my Triumph using xda premium
Yes i am able to get to download mode
Well after some tinkering (replacing the recovery image, assuming something corrupted it) i can now get to recovery, still takes 10 min to load it though. But i am unable to do anything in recovery because i have to press the menu button to confirm selection but the buttons wont respond. Some help would be appreciated.
Hello all,
Yesterday night, I've updated to CM10 latest version through auto-update features of CM10. After downloaded and click update, it's reboot and stucked at HTC Boot screen. I've tried to go into recovery mode by pressing Power button + Volumne Down button. It's doesn't go in, it's just keep rebooting.
Then, I've tried connecting with usb cable and tried to fastboot reboot and fastboot reboot-bootloader, but nothing happened. On fastboot screen, it's just <waiting device>
Please kindly help me out.
Thank you very much.
As soon as it starts booting hold down the power. Should shut it off completely. Press vol down then power and hold until bootloader comes up. Had a problem similar to this and it takes a couple of attempts to get it.
Sent from my HTC One X using xda app-developers app
im using a tmobile samsung galaxy reverb and i installed cwm and a new rom. all was good till i installed rom toolbox and i was using the boot animation randomizer. it worked fine the first reboot then the next one the boot image never left the screen but i can rotate my screen and see half of my home screen also go into all my apps but i cannot see the upper/left half of my screen. i held down the power and vol down button and it goes to into the warning page about istalling a custom OS instead of CWM. can anybody please help me out with this???!!!
Is I'm not mistaken.. You want to power off your device. Then press power, home, and volume up to get to recovery.. (Not sure about home). I do know that volume down sends you to "download" which is not what you want.
Sent from my SGH-T889 using xda premium
Hi All,
I've turned on my Xoom after a while and then I've got stuck in the Boot screen with the Motorola logo and the following message in the left upper corner: Starting RSD Protocol Support 3.
I tried to do Power + Volume Up for approx 1min. to do a soft reset and nothing happened. It's frozen.
In addition, I've connected the Xoom MZ600 to the PC and downloaded RSDLite v6.1.4, It gets detected and gets connected by the way... and also downloaded the VZW_MZ600_Signed_HRI39_Signed_MDM600BP_C_02.0F.00R_SW.combo.sbf.
Then I started to flash it and all went ok, Last message was Passed, but when the tablet is rebooting it gets stuck again in the "Starting RSD Protocol Support 3".
Also, when it was going to reboot after the RDSLite, I tried to press Volume down to try to get to fastboot, but nothing happens, it gets straight away to the "Starting RSD Protocol Support 3".
So, NO fastboot is available... although I saw a fastboot option in the RSDLite.
Please any other way to get it back?
Thanks in advance.
egmweb said:
Hi All,
I've turned on my Xoom after a while and then I've got stuck in the Boot screen with the Motorola logo and the following message in the left upper corner: Starting RSD Protocol Support 3.
I tried to do Power + Volume Up for approx 1min. to do a soft reset and nothing happened. It's frozen.
In addition, I've connected the Xoom MZ600 to the PC and downloaded RSDLite v6.1.4, It gets detected and gets connected by the way... and also downloaded the VZW_MZ600_Signed_HRI39_Signed_MDM600BP_C_02.0F.00R_SW.combo.sbf.
Then I started to flash it and all went ok, Last message was Passed, but when the tablet is rebooting it gets stuck again in the "Starting RSD Protocol Support 3".
Also, when it was going to reboot after the RDSLite, I tried to press Volume down to try to get to fastboot, but nothing happens, it gets straight away to the "Starting RSD Protocol Support 3".
So, NO fastboot is available... although I saw a fastboot option in the RSDLite.
Please any other way to get it back?
Thanks in advance.
Click to expand...
Click to collapse
Hold down the volume down key while turning the Xoom on and keep it down until you see some text on the bootloader screen. At that stage you should be in fastboot mode. If you get to fastboot mode, unlock your bootloader, then see if it boots.
oldblue910 said:
Hold down the volume down key while turning the Xoom on and keep it down until you see some text on the bootloader screen. At that stage you should be in fastboot mode. If you get to fastboot mode, unlock your bootloader, then see if it boots.
Click to expand...
Click to collapse
Thanks very much for your comment.
I've already tried this and as I said in my original post... it's frozen... no Power button + Volume up/down works...
Any other suggestion?
thanks in advance.
egmweb said:
Thanks very much for your comment.
I've already tried this and as I said in my original post... it's frozen... no Power button + Volume up/down works...
Any other suggestion?
thanks in advance.
Click to expand...
Click to collapse
OK. Boot up and once you see RSD Protocol 3 on the screen, press and hold volume up + power until the Xoom reboots. When it does, does it boot normally or does it still go to RSD?
Sent from my Xoom using Tapatalk 4
oldblue910 said:
OK. Boot up and once you see RSD Protocol 3 on the screen, press and hold volume up + power until the Xoom reboots. When it does, does it boot normally or does it still go to RSD?
Sent from my Xoom using Tapatalk 4
Click to expand...
Click to collapse
Hello oldblue910, Thanks very much for your help. However, pressing and holding volume up + power at the Xoom doesn't do anything.
Hmmm... with the Xoom at the RSD screen, volume up + power should reboot the device. If that's not doing anything, I'll have to do some more research tomorrow. I'll get back to you.
Sent from my Galaxy S4 GT-I9505G using Tapatalk 4
Reflash using RSD/Sbf
ThePunisher ~ Tapa4