just did a clean install v20d via lgmdp and then rooted it, thus loosing all the custom recovery (CR)
now here the problem arises...
installed ROM manager and found that it isn't showing the CR for new baseband (BB), just shows for the old one
installed goo manager and found that it still isn't compatible with our device
i found a file "twrp-thunderg-2.0.0alpha1.img" on internet while searching for device compatibility
now what should I do to install custom recovery?
all i have is .img files for both clockwork and twrp. I don't trust twrp coz they still aren't showing official status for our device
update -
i flashed recovery via lgmdp tool
but still, whats with the recovery mess?
Not sure. Possibly not supported anymore.
You can also use shinobisofts recovery flash tool.
I had done same as you and used it to flash cwm.
savagephoenix said:
Not sure. Possibly not supported anymore.
You can also use shinobisofts recovery flash tool.
I had done same as you and used it to flash cwm.
Click to expand...
Click to collapse
He figured out he could also flash a recovery with LGMDP.
---------- Post added at 11:46 PM ---------- Previous post was at 11:41 PM ----------
van_helsing_80 said:
update -
i flashed recovery via lgmdp tool
but still, whats with the recovery mess?
Click to expand...
Click to collapse
The recovery is a mechanism to repair or restore the devices OS. It is also utilized to install ROMs and updates.
sorry, what I meant was regarding the incompatibilities with the recovery. That was kind of you to explain what recovery is.
Related
Help,
I rooted my VZW s3 and all was good until i tried to update to a CM10 rom..
It would not install the zip file.. I followed all the guides about backing up the imei file ect.. and I used the correct recovery.. it would not install..I kept getting erros with the ROM zip files I downloaded. so i tried the ez recovery app and installed TWRP.. I like that and have used it in the past.. well I forgot that I cant restore a backup from CWM. so now im stuck bootlooping into TWRP recovery.
Any help?
I was installing TWRP while my GF was talking to me. Not that I'm blaming her or anything but I failed to add the "dd" during the manual install. Now I'm downloading the stock rom and going to try Odin to get my phone functioning again.
Twrp doesn't support kexec, so it will only boot stock based ROM's
sent from locked bootloadrer SGS3 running a custom kernel
wera750 said:
Twrp doesn't support kexec, so it will only boot stock based ROM's
sent from locked bootloadrer SGS3 running a custom kernel
Click to expand...
Click to collapse
can somebody send me a link to a stock rom so I can start this over?
I cant even get adb to recognize my device when its on.. I only have TWRP bootlooping into recovery...
Thanks..
sidn3y said:
I was installing TWRP while my GF was talking to me. Not that I'm blaming her or anything but I failed to add the "dd" during the manual install. Now I'm downloading the stock rom and going to try Odin to get my phone functioning again.
Click to expand...
Click to collapse
Not saying this will help you, but it did with me. I have no idea how.
Tried vol down/home/power and it booted into the custom rom screen. Cancelled that. It rebooted normally..
---------- Post added at 09:48 PM ---------- Previous post was at 09:48 PM ----------
kwiksilvr said:
can somebody send me a link to a stock rom so I can start this over?
I cant even get adb to recognize my device when its on.. I only have TWRP bootlooping into recovery...
Thanks..
Click to expand...
Click to collapse
http://stockroms.net/file/GalaxyS3/SGH-I535/StockROMS.net-SCH-I535_VZW_Verizon.zip
Hello all,
I have been going slightly mad today trying to get my mate 7 2GB back from CWM to stock recovery. The main problem is that I do not have a stock recovery image. But after being shown where to find one, I noticed that I could not get it successfully flashed either.
Since I do not really know how to do this, I used flashify, but that did not work and either returned me to the CWM or sent me to rescue.
Can someone help me to a) get a stock recovery image for the Mate 7 version MT7-L09 and b) show me how to properly flash it?
Find stock recovery is easy.. only a question why flashify don't work for you? It work fine for me... your device is rooted?
djzero86 said:
Find stock recovery is easy.. only a question why flashify don't work for you? It work fine for me... your device is rooted?
Click to expand...
Click to collapse
Hi @dzjero86, my device is rooted and I am on the B137SP03 version atm, using CWM. Don't know why Flashify is not working for flashing a recovery image. It works fine to flash a CWM recovery. Maybe I have the wrong stock recovery... If you can find it, can you send me the link or add it as an attachment here?
Please guys help me to . i have that same problem i have been trying to flash the stock recovery again but i couldn't even with flashify after i flash i takes me to bootloader screen and it shows me a fun_error message
I have a tl-10 device
dekraan said:
Hi @dzjero86, my device is rooted and I am on the B137SP03 version atm, using CWM. Don't know why Flashify is not working for flashing a recovery image. It works fine to flash a CWM recovery. Maybe I have the wrong stock recovery... If you can find it, can you send me the link or add it as an attachment here?
Click to expand...
Click to collapse
A way to find the stock recovery is : download the whole B137SP03 Rom from the Huawei site , and use a tool called "Firmware unpacker for Huawei" whit this tool you can extract the recovery.img from the Rom and try to flash it using flashify
Firmware unpacker
http://forum.xda-developers.com/mate-7/development/firmware-unpacker-huawei-t2879754
Rom
http://forum.xda-developers.com/mate-7/general/firmware-huawei-ascend-mate-7-b137sp03-t3041629
Pd : I am not a developer or anything similar but I have some years of experience rooting and etc ...
---------- Post added at 10:12 AM ---------- Previous post was at 10:00 AM ----------
Ali_adel_medo said:
Please guys help me to . i have that same problem i have been trying to flash the stock recovery again but i couldn't even with flashify after i flash i takes me to bootloader screen and it shows me a fun_error message
I have a tl-10 device
Click to expand...
Click to collapse
You have a unlocked bootloader???
Yes i have unlocked and rooted the phone using the cwm recovery and now a i can't flash the stock recovery any more
Ali_adel_medo said:
Yes i have unlocked and rooted the phone using the cwm recovery and now a i can't flash the stock recovery any more
Click to expand...
Click to collapse
Do you tried flash via fastboot ?
fastboot flash recovery recovery.img
Or try to use this tool
http://forum.xda-developers.com/mat...custom-recovery-tool-mt7-l10-l10-mt7-t3022424
This should work.
The fast boot just stucks at waiting for device
And the tool you send says that the stock recovery works only on tl_09 and my device is tl_10
djzero86 said:
A way to find the stock recovery is : download the whole B137SP03 Rom from the Huawei site , and use a tool called "Firmware unpacker for Huawei" whit this tool you can extract the recovery.img from the Rom and try to flash it using flashify
Firmware unpacker
http://forum.xda-developers.com/mate-7/development/firmware-unpacker-huawei-t2879754
Rom
http://forum.xda-developers.com/mate-7/general/firmware-huawei-ascend-mate-7-b137sp03-t3041629
Pd : I am not a developer or anything similar but I have some years of experience rooting and etc ...
---------- Post added at 10:12 AM ---------- Previous post was at 10:00 AM ----------
You have a unlocked bootloader???
Click to expand...
Click to collapse
Ok, I couldnt access your firmware unpacker, but I did manage to use the tool you suggested.
I have a different recovery screen, but is this the right one? It has EMUI large in centre screen and the options reboot system now, wipe data/factory reset and wipe cache partition.
If this is the correct one, and I am already on the D137SP03 ROM, I should be able to locally update right?
I tried this, and got a lot further this time, but my phone gave an error message during the update. Do I need to flash the original B137SP03 rom again, even though I am already on it?
I think you maybe can flash using adb commands and also you need adb drivers working
---------- Post added at 11:23 AM ---------- Previous post was at 11:15 AM ----------
dekraan said:
Ok, I couldnt access your firmware unpacker, but I did manage to use the tool you suggested.
I have a different recovery screen, but is this the right one? It has EMUI large in centre screen and the options reboot system now, wipe data/factory reset and wipe cache partition.
If this is the correct one, and I am already on the D137SP03 ROM, I should be able to locally update right?
I tried this, and got a lot further this time, but my phone gave an error message during the update. Do I need to flash the original B137SP03 rom again, even though I am already on it?
Click to expand...
Click to collapse
Ok.... you have the stock recovery now???
djzero86 said:
I think you maybe can flash using adb commands and also you need adb drivers working
---------- Post added at 11:23 AM ---------- Previous post was at 11:15 AM ----------
Ok.... you have the stock recovery now???
Click to expand...
Click to collapse
I think so. If stock looks like I described: black screen, large EMUI logo, and the options reboot system now, wipe data/factory reset and wipe cache partition?
That's right... you have stock recovery... sometimes the update fail if the UPDATE.APP is on the internal storage.. try to flash from a micro sd card or re-download the update ....
English is not my first language...
djzero86 said:
That's right... you have stock recovery... sometimes the update fail if the UPDATE.APP is on the internal storage.. try to flash from a micro sd card or re-download the update ....
English is not my first language...
Click to expand...
Click to collapse
Great, thank you for your fantastic help!
I will get a new micro-sd card tomorrow, and will try it right away!
Good luck... come back to report
djzero86 said:
Good luck... come back to report
Click to expand...
Click to collapse
No luck so far.... I've downloaded the update.zip, put it in my mnt/ext_sdcard/dload folder and start the local update. It begins OK, as the progress bar moves along. But after about 25% it shoots to the end, and then I get an update failed screen with a red exclamation mark.
What could I try to get it to work??
dekraan said:
No luck so far.... I've downloaded the update.zip, put it in my mnt/ext_sdcard/dload folder and start the local update. It begins OK, as the progress bar moves along. But after about 25% it shoots to the end, and then I get an update failed screen with a red exclamation mark.
What could I try to get it to work??
Click to expand...
Click to collapse
Ok, I just reinstalled the B137P03 version from the how to install lollipop thread, and that went successful. Now going to try the update.zip! Keep you posted
Ah, now we're talking It seems to have worked. Phone is now showing 'Android is upgrading' and 'optimising app.....'
Great! It does seem strange I had to reinstall the B137SP03 rom, but that did the trick!
So I got my note 5 and tried installing clockwork recovery and now my phones bricked. When trying to flash the stock rom using odin, it always crashes and says fail.
Has anyone had the same problem?
It sounds like your phone is running the newer firmware. You have to flash the full ogd firmware, oa6 firmware will not flash over any of the newer ones.
tdunham said:
It sounds like your phone is running the newer firmware. You have to flash the full ogd firmware, oa6 firmware will not flash over any of the newer ones.
Click to expand...
Click to collapse
any idea where to get the OJ6 Firmware
---------- Post added at 06:26 PM ---------- Previous post was at 05:48 PM ----------
hey this guy is legit he got me up and running again all for $20 http://jcunlocks.com/
spenava944 said:
So I got my note 5 and tried installing clockwork recovery and now my phones bricked. When trying to flash the stock rom using odin, it always crashes and says fail.
Has anyone had the same problem?
Click to expand...
Click to collapse
Clockwork recovery isn't supported for the Note 5. Twrp recovery is what you have to use.
At this point, you can try to flash twrp through Odin or get the stock tar and go back to stock and start the root and flash recovery process again.
Yea what he said. Stock via odin and restarting. The easiest thing would be is to download twrp and flash it via odin. The system/rom should be fine it just the recovery
I have tried to install cm12.1 nightly through cyanogen recovery and it got stuck in cyanogen fast bootmode .when I try to power on my device yu logo gets blink and auto turnoffs ...please help me ......in what way can I get back my phone ?? Can customer care solve the issue? :'(
You are lucky its soft bricked not hard
You got backup of boot.img?
flash it to phone via fastboot
arshad145 said:
You are lucky its soft bricked not hard
You got backup of boot.img?
flash it to phone via fastboot
Click to expand...
Click to collapse
No bro ...
While connected to system it cannot detect my device
Have you tried to search for ROMs for your phone model?
Google or Search at www.needrom.com
Take a note....
Do you included your kernel in cwm (i mean porting cwm)??
you have to flash stock recovery or working cwm recovery optionally(may be) boot.img
1. If u found a stock rom,confirm that the rom is working
2. Don't touch preloader coz it will make things worse...
3. use latest version of SP flash tool.
4. if u can't find a stock rom find a clone of your phone and use that (Kernal may be upgraded or downgraded)
5. Post a request of a boot.img and recovery.img
aravazhi_mdr said:
Do you included your kernel in cwm (i mean porting cwm)??
you have to flash stock recovery or working cwm recovery optionally(may be) boot.img
1. If u found a stock rom,confirm that the rom is working
2. Don't touch preloader coz it will make things worse...
3. use latest version of SP flash tool.
4. if u can't find a stock rom find a clone of your phone and use that (Kernal may be upgraded or downgraded)
5. Post a request of a boot.img and recovery.img
Click to expand...
Click to collapse
You are going for the most extreme case =/
arshad145 said:
You are going for the most extreme case =/
Click to expand...
Click to collapse
going serious,,,,?
I meant no need for SP Flash Tool?
coz he got a Qualcomm? and not MTK?
So he needs QFIL not SPFT ... ?!
aravazhi_mdr said:
Do you included your kernel in cwm (i mean porting cwm)??
you have to flash stock recovery or working cwm recovery optionally(may be) boot.img
1. If u found a stock rom,confirm that the rom is working
2. Don't touch preloader coz it will make things worse...
3. use latest version of SP flash tool.
4. if u can't find a stock rom find a clone of your phone and use that (Kernal may be upgraded or downgraded)
5. Post a request of a boot.img and recovery.img
Click to expand...
Click to collapse
No bro.. I have not included kernel in cwm . I have downloaded a stock rom .but when I try to unlock my bootloader it says oem unlock not possible.how to flash it now? Pls send me the link of boot.IMG and recovery. Img
arshad145 said:
I meant no need for SP Flash Tool?
coz he got a Qualcomm? and not MTK?
So he needs QFIL not SPFT ... ?!
Click to expand...
Click to collapse
Sorry bro....
I thought he is using chinese phone and got mediatek chipset....
---------- Post added at 09:36 AM ---------- Previous post was at 09:27 AM ----------
sai978 said:
No bro.. I have not included kernel in cwm . I have downloaded a stock rom .but when I try to unlock my bootloader it says oem unlock not possible.how to flash it now? Pls send me the link of boot.IMG and recovery. Img
Click to expand...
Click to collapse
please mention your mobile model and chipset.
you flashed cwm in fastboot and now it is locked....?
aravazhi_mdr said:
Sorry bro
please mention your mobile model and chipset.
you flashed cwm in fastboot and now it is locked....?
Click to expand...
Click to collapse
Device name - yu yunique 4711
Got qualcom . I have flashed cyanogen recovery through twrp recovery and after that I have installed cm12.1 nightly and I forgot to wipe cache and tapped on reboot.now if I try to power on my device yu logo blinks and auto power offs. But I was able to enter cyanogen fastboot mode
WTF?! U flashed a recovery through another recovery!!!?
---------- Post added at 09:45 ---------- Previous post was at 09:44 ----------
ok =/ so.... u got stock recovery?
or can u go to any other place except fastboot??
sai978 said:
Device name - yu yunique 4711
Got qualcom . I have flashed cyanogen recovery through twrp recovery and after that I have installed cm12.1 nightly and I forgot to wipe cache and tapped on reboot.now if I try to power on my device yu logo blinks and auto power offs. But I was able to enter cyanogen fastboot mode
Click to expand...
Click to collapse
So you have working TWRP....
Download Qualcom Image flash tool and flash TWRP then wipe data
try it
arshad145 said:
WTF?! U flashed a recovery through another recovery!!!?
---------- Post added at 09:45 ---------- Previous post was at 09:44 ----------
ok =/ so.... u got stock recovery?
or can u go to any other place except fastboot??
Click to expand...
Click to collapse
I can enter only fast boot mode bro. I have downloaded stock rom but bootloader got locked again bro. So I was not able to flash anything. When Itry to unlock it says oem unlock not possible
aravazhi_mdr said:
So you have working TWRP....
Download Qualcom Image flash tool and flash TWRP then wipe data
try it
Click to expand...
Click to collapse
I will try bro. But my question is can I flash this without unlocking bootloader
sai978 said:
I can enter only fast boot mode bro. I have downloaded stock rom but bootloader got locked again bro. So I was not able to flash anything. When Itry to unlock it says oem unlock not possible
Click to expand...
Click to collapse
good to go....
use QIFT
---------- Post added at 11:02 AM ---------- Previous post was at 10:59 AM ----------
sai978 said:
I will try bro. But my question is can I flash this without unlocking bootloader
Click to expand...
Click to collapse
I also had that problem fastboot said have no permission....and can't do that...
as i have mediatek i flashed using SPFT
http://www.gizmoadvices.com/unlock-bootloader-on-yu-yunique-yu4711/
Have you tried this?
Unlocked bootloader then flash will work..
arshad145 said:
http://www.gizmoadvices.com/unlock-bootloader-on-yu-yunique-yu4711/
Have you tried this?
Unlocked bootloader then flash will work..
Click to expand...
Click to collapse
Yes I have . but when I type the command fastboot oem unlock-go it says unable to unlock bootloader and the main thing is I can only enter cyanogen fastbootmode
aravazhi_mdr said:
good to go....
use QIFT
---------- Post added at 11:02 AM ---------- Previous post was at 10:59 AM ----------
I also had that problem fastboot said have no permission....and can't do that...
as i have mediatek i flashed using SPFT
Click to expand...
Click to collapse
Bro which is better to flash?? Boot.img or twrp.img
twrp is better as u can flash whole rom
---------- Post added at 18:14 ---------- Previous post was at 18:13 ----------
boot img will unlock bootloop but not neccessary if u need a working rom
I am using Peter's recovery and wish to go back to stock recovery as installing ota is tiring. How can I do that without losing data and files?
If you are using official MIUI ROM, dirty flashing full recovery ROM will also overwrite custom recovery with stock recovery.
AbioticSpoon said:
I am using Peter's recovery and wish to go back to stock recovery as installing ota is tiring. How can I do that without losing data and files?
Click to expand...
Click to collapse
are you rooted?
if ues then just unroot using magisk unistaller and reboot it will restore stock recovery then use ota to update then again you can flash twrp peter recovery by fastboot and boot in to recovery and then flash magisk it will again have both recovery and root
my device shows encrypted status
AbioticSpoon said:
I am using Peter's recovery and wish to go back to stock recovery as installing ota is tiring. How can I do that without losing data and files?
Click to expand...
Click to collapse
Just download the fast boot rom from the official website and flash it by mi flash tool.
And during flashing it select flash all except data.
And you will lose nothing and your recovery will be restored.
Then you can flash ota by that.
---------- Post added at 08:23 PM ---------- Previous post was at 08:21 PM ----------
blueandro said:
are you rooted?
if ues then just unroot using magisk unistaller and reboot it will restore stock recovery then use ota to update then again you can flash twrp peter recovery by fastboot and boot in to recovery and then flash magisk it will again have both recovery and root
my device shows encrypted status
Click to expand...
Click to collapse
Really?
I should try this.
Have you tried this, what is the concept behind this?
How can unrooting can restore stock recovery?
yes i have tried it and i m on latest stable 10.3
13
blueandro said:
yes i have tried it and i m on latest stable 10.3
13
Click to expand...
Click to collapse
Complete uninstall or just restore image option?
---------- Post added at 01:24 PM ---------- Previous post was at 01:22 PM ----------
blueandro said:
yes i have tried it and i m on latest stable 10.3
13
Click to expand...
Click to collapse
And are u encrypted? Means does twrp ask for screen lock password during going to recovery?
gautamajay52 said:
Complete uninstall or just restore image option?
---------- Post added at 01:24 PM ---------- Previous post was at 01:22 PM ----------
And are u encrypted? Means does twrp ask for screen lock password during going to recovery?
Click to expand...
Click to collapse
using peters recovery latest one
i m not using my fone with lock password so it didn't ask
blueandro said:
using peters recovery latest one
i m not using my fone with lock password so it didn't ask
Click to expand...
Click to collapse
Ok... I will try this... wating for new update that i can verify it too.
Thanks
I have one solution
simple
just things needed are:
1. miui stock recovery img
2. vbmeta
next,
1. First flash recovery image.
2. Then flash vbmeta image.
what does vbmeta do. it actually saves the recovery image after flashing new recovery.
3. Finished reboot