So, for installing TWRP you need to follow these steps:
IMP:
[*] You need not to have rooted phone.
[*] This is for MMX A89 ONLY! Don't use for other phones as you can brick it!
[*] Although, this rom has been tested, I'm not responsible for any damage!
Prerequisites :
1. MTK6577 Drivers (Thanks to Bhardik)
2. SP Flash Tool (Thanks to Bhardik)
3. TWRP Itself! (Thanks to yuweng
Now we are ready to Flash!
[IMPORTANT : DISCONNECT YOUR PHONE BEFORE STARTING THIS TUTORIAL]
1. First of all, Download all of the packages listed above.
2. Install Drivers and Extract SP Flash Tools & TWRP image.
3. Now open extracted SP Flash Tool folder and run Flash_tool.exe
4. Click on "Scatter-loading" button which is on the right side below Downloading Agent. A new window will open. Browse to the extracted "TWRP for MMX A89-dan.man" folder and select "MT6577_Android_scatter_emmc.txt" file.
Refer this screenshot for more help:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
5. Flash tool will populate the Map file on the application window. You will see multiple entries. Uncheck all entries except for RECOVERY.
6. [Skip this step if recover.img is already selected] Now to select recovery file, click on recovery and select recovery.img file.
7. Now click on "Download". Warning message will occur, but ignore that and click Yes.
7. You will see in the status bar below "Searching", now connect your phone (with battery inserted + Press and Hold Volume Up Key) via the USB cable. Keep those buttons holding while the process is completing.
8. Wait for the process to finish and then you will get a window showing green circle.
Congrats You have flashed TWRP Recovery v2.3.2.3 ! Enjoy!
Note: If you get any error in SP Flash Tool, then recheck your MTK drivers installation or manually install them through device manager.
Click to expand...
Click to collapse
-------------
Booting into TWRP Recovery v2.3.2.3 is the same as in the stock recovery. Switch on the phone with "Volume Up" and "Power" button Pressed. The Phone will boot into TWRP Recovery v2.3.2.3!
Here's a screenshot of TWRP working on my A89 :
-------------
CREDITS GOES TO YUWENG & BHARDIK :highfive:
All Credit goes to yuweng for creating the ROM and BHARDIK who has made CWM for A89 and helped compiling this tutorial.
And GREAT thanks to the Russian Master Shifu Javum, as he is the one that compile TWRP for our MT6577... :good:
Click to expand...
Click to collapse
dan.man said:
So, for installing TWRP you need to follow these steps:
IMP:
[*] You need not to have rooted phone.
[*] This is for MMX A89 ONLY! Don't use for other phones as you can brick it!
[*] Although, this rom has been tested, I'm not responsible for any damage!
Prerequisites :
1. MTK6577 Drivers (Thanks to Bhardik)
2. SP Flash Tool (Thanks to Bhardik)
3. TWRP Itself! (Thanks to yuweng
Now we are ready to Flash!
[IMPORTANT : DISCONNECT YOUR PHONE BEFORE STARTING THIS TUTORIAL]
1. First of all, Download all of the packages listed above.
2. Install Drivers and Extract SP Flash Tools & TWRP image.
3. Now open extracted SP Flash Tool folder and run Flash_tool.exe
4. Click on "Scatter-loading" button which is on the right side below Downloading Agent. A new window will open. Browse to the extracted "TWRP for MMX A89-dan.man" folder and select "MT6577_Android_scatter_emmc.txt" file.
Refer this screenshot for more help:
5. Flash tool will populate the Map file on the application window. You will see multiple entries. Uncheck all entries except for RECOVERY.
6. [Skip this step if recover.img is already selected] Now to select recovery file, click on recovery and select recovery.img file.
7. Now click on "Download". Warning message will occur, but ignore that and click Yes.
7. You will see in the status bar below "Searching", now connect your phone (with battery inserted + Press and Hold Volume Up Key) via the USB cable. Keep those buttons holding while the process is completing.
8. Wait for the process to finish and then you will get a window showing green circle.
Congrats You have flashed TWRP Recovery v2.3.2.3 ! Enjoy!
-------------
Booting into TWRP Recovery v2.3.2.3 is the same as in the stock recovery. Switch on the phone with "Volume Up" and "Power" button Pressed. The Phone will boot into TWRP Recovery v2.3.2.3!
Here's a screenshot of TWRP working on my A89 :
-------------
Click to expand...
Click to collapse
I use this its awesome
Sir I have rooted my phone micromax q336 with kingroot but unable to flash twrp or any other custom recovery I am not having a pc ko please somebody
Related
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
How to install Team Win Recovery In You Micromax A89
Click to expand...
Click to collapse
Edit: - Internal Storage not detected Bug fixed
Click to expand...
Click to collapse
Method : SP Flash Tool method, root not required
1. Download MTK6577 Drivers.zip and unzip/extract on your Windows PC, just run InstallDriver.exe to install drivers.
Click to expand...
Click to collapse
2. Download TWRP Recovery v2.4.0 and SP_Flash_Tool_v3.1220.02_FOR_S101A.zip , unzip/extract them.
Click to expand...
Click to collapse
3. Now open extracted SP Flash Tool folder and run Flash_tool.exe
4. Click on "Scatter-loading" button which is on the right side below Downloading Agent. A new window will open. Browse to the extracted TWRP Recovery v2.4.2.0 folder and select MT6577_Android_scatter_emmc.txt file.
5. Flash tool will populate the Map file on the application window. You will see multiple entries. Uncheck all entries except for RECOVERY.
6. Now click on "Download". Warning message will occur, but ignore that and click Yes.
7. You will see in the status bar below "Searching", now connect your phone (with battery inserted + Press and Hold Volume Up Key) via the USB cable.
8. Wait for the process to finish and then you will get a window showing green circle.
Very Easy & safe way to FLASH CWM RECOVERY Without having PC
steps:->
1. Downlaod TWRP Recovery v2.4.2.0 extract it and copy recovery.img only to root of your SD Cards
2: download MobileUncleTools for MTK from the attachments and install it as normal apps
3. Now open MobileUncleTools apps you recently installed.
4. grant Superuser permissions
5. There click on recovery update menu
6. Then click on the recovery image name of ‘recovery.img’
7. Let the app install the recovery. after it automatically reboot your device in to recovery
8. now remove battery from device and reinsert it and then reboot device to recovery using volume up + power key
done your TWRP is appears there
Click to expand...
Click to collapse
Screenshots of Mobile uncle tutorials
Click to expand...
Click to collapse
Some SS Tutorials for how to flash CWMR using SP Flash Tools
Click to expand...
Click to collapse
Check here all steps
Click to expand...
Click to collapse
Congrats You have flashed TWRP Recovery v2.4.2.0 !
Note: If you get any error in SP Flash Tool, then recheck your MTK drivers installation or manually install them through device manager.
Booting into TWRP Recovery v2.4.2.0 is the same as in the stock recovery. Switch on the phone with "Volume Up" and "Power" button Pressed. The Phone will boot into TWRP Recovery v2.4.2.0 !
I have also attached the the Stock Recovery.zip.
Credit : -
Varun Chitre
yuweng
Cygwin
Me
dont say Thanks Hit
if you can
Click to expand...
Click to collapse
or use mobile uncle tools app to flash various recovery..no need of spflashtool...
BHARDIK said:
How to install clockworkmod recovery:
Edit: Fixed install zip from sdcard bug
Method : SP Flash Tool method, root not required
1. Download MTK6577 Drivers.zip and unzip/extract on your Windows PC, just run InstallDriver.exe to install drivers.
2. Download TWRP Recovery v2.3.2.3 and SP_Flash_Tool_v3.1220.02_FOR_S101A.zip , unzip/extract them.
3. Now open extracted SP Flash Tool folder and run Flash_tool.exe
4. Click on "Scatter-loading" button which is on the right side below Downloading Agent. A new window will open. Browse to the extracted TWRP Recovery v2.3.2.3 folder and select MT6577_Android_scatter_emmc.txt file.
5. Flash tool will populate the Map file on the application window. You will see multiple entries. Uncheck all entries except for RECOVERY.
6. Now click on "Download". Warning message will occur, but ignore that and click Yes.
7. You will see in the status bar below "Searching", now connect your phone (with battery inserted + Press and Hold Volume Up Key) via the USB cable.
8. Wait for the process to finish and then you will get a window showing green circle.
Congrats You have flashed TWRP Recovery v2.3.2.3 !
Note: If you get any error in SP Flash Tool, then recheck your MTK drivers installation or manually install them through device manager.
Booting into TWRP Recovery v2.3.2.3 is the same as in the stock recovery. Switch on the phone with "Volume Up" and "Power" button Pressed. The Phone will boot into TWRP Recovery v2.3.2.3!
I have also attached the the Stock Recovery.zip.
Click to expand...
Click to collapse
great
sahil11 said:
great
Click to expand...
Click to collapse
Thanks Sahil11 @
Hardy
Clockworkmod 6.0.2.8 Updates for Micromax A90s
Click to expand...
Click to collapse
Tested by me working fine
Click to expand...
Click to collapse
Root Required
Click to expand...
Click to collapse
Very Easy & safe way to FLASH CWM RECOVERY in any Android Device
steps:->
1. Downlaod CWM recovery.img
2: download recovery manager from HERE now Copy CWM recovery.img in SD card, now install the recovery manager.apk normally
3. Now open the recovery manager app you recently installed.
4. Click on recovery in app menu.
5. There click on install recovery
6. Then click on the recovery image name of ‘recovery.img’
7. Let the app install the recovery. after it done a message will show.
current recovery : unrecognized…. just ignore it.
That’s all now you have installed your recovery
Click to expand...
Click to collapse
SP Flash Tool method, root not required
Click to expand...
Click to collapse
Important Notes this given Screenshots only 4 example its not for any proper device
Click to expand...
Click to collapse
here is guides how to flash CWM 6.0.2.8 in A90s ( Dual Core One Not A90)
Click to expand...
Click to collapse
1. Download MTK6577 Drivers.zip and unzip/extract on your Windows PC, just run InstallDriver.exe to install drivers.
2. Download CWM Recovery v6.0.2.8 + MT6577 Scatter.zip and SP_Flash_Tool_v3.1222
3. Now open extracted SP Flash Tool folder and run Flash_tool.exe
4. Click on "Scatter-loading" button which is on the right side below Downloading Agent. A new window will open. Browse to the extracted CWM Recovery v6.0.2.8 + scatter folder and select MT6577_Android_scatter_emmc.txt file.
5. Flash tool will populate the Map file on the application window. You will see multiple entries. Uncheck all entries except for RECOVERY.
6. Now click on "Download".or Press " F9 " Warning message will occur, but ignore that and click Yes.
7. You will see in the status bar below "Searching", now connect your phone (without battery inserted) via the USB cable.
8. Wait for the process to finish and then you will get a window showing green circle.
Some SS Tutorials for how to flash CWMR using SP Flash Tools
Click to expand...
Click to collapse
Check here all steps
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Click to expand...
Click to collapse
Congrats You have flashed CWM Recovery v6.0.2.8
Note: If you get any error in SP Flash Tool, then recheck your MTK drivers installation or manually install them through device manager.
Booting into CWM recovery is the same as in the stock recovery. Switch on the phone with "Volume Up" and "Power" button Pressed. The Phone will boot into CWM!
I have also attached the the Stock Recovery.zip.
Credit : -
bgcngm
yuweng
Cygwin
Me
dont say Thanks Hit
if you can
Click to expand...
Click to collapse
easy method
BHARDIK said:
1. Download MTK6577 Drivers.zip and unzip/extract on your Windows PC, just run InstallDriver.exe to install drivers.
2. Download CWM Recovery v6.0.2.8 + MT6577 Scatter.zip and SP_Flash_Tool_v3.1222
3. Now open extracted SP Flash Tool folder and run Flash_tool.exe
4. Click on "Scatter-loading" button which is on the right side below Downloading Agent. A new window will open. Browse to the extracted CWM Recovery v6.0.2.8 + scatter folder and select MT6577_Android_scatter_emmc.txt file.
5. Flash tool will populate the Map file on the application window. You will see multiple entries. Uncheck all entries except for RECOVERY.
6. Now click on "Download".or Press " F9 " Warning message will occur, but ignore that and click Yes.
7. You will see in the status bar below "Searching", now connect your phone (without battery inserted) via the USB cable.
8. Wait for the process to finish and then you will get a window showing green circle.
Congrats You have flashed CWM Recovery v6.0.2.8
Note: If you get any error in SP Flash Tool, then recheck your MTK drivers installation or manually install them through device manager.
Booting into CWM recovery is the same as in the stock recovery. Switch on the phone with "Volume Up" and "Power" button Pressed. The Phone will boot into CWM!
I have also attached the the Stock Recovery.zip.
Click to expand...
Click to collapse
Just use mobile uncle works fine
nimo1996 said:
Just use mobile uncle works fine
Click to expand...
Click to collapse
I want to flash stock rom on my micromax a90s. i did not take backup before rooting but i took a backup with mobileuncle tk tools after rooting my phone only. Is there a way i can get back my stock ROM. please explain the processs. Eagerly waiting
Nice tutor !!
Use full tutor thanks dude !!
again thanks for new CWM
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Note :-> This is tested Recovery by me but still M not responsible for any damage in your device
Click to expand...
Click to collapse
How to install Team Win Recovery In Your Micromax A90s
Method : SP Flash Tool method, root not required
1. Download MTK6577 Drivers.zip and unzip/extract on your Windows PC, just run InstallDriver.exe to install drivers.
Click to expand...
Click to collapse
2. Download TWRP Recovery v2.4.2.0 and SP_Flash_Tool_v3.1220.02.zip , unzip/extract them.
Click to expand...
Click to collapse
3. Now open extracted SP Flash Tool folder and run Flash_tool.exe
4. Click on "Scatter-loading" button which is on the right side below Downloading Agent. A new window will open. Browse to the extracted TWRP Recovery v2.4.2.0 folder and select MT6577_Android_scatter_emmc.txt file.
5. Flash tool will populate the Map file on the application window. You will see multiple entries. Uncheck all entries except for RECOVERY.
6. Now click on "Download". Warning message will occur, but ignore that and click Yes.
7. You will see in the status bar below "Searching", now connect your phone (with battery inserted + Press and Hold Volume Up Key) via the USB cable.
8. Wait for the process to finish and then you will get a window showing green circle.
Very Easy & safe way to FLASH CWM RECOVERY Without having PC
steps:->
1. Downlaod TWRP Recovery v2.4.2.0 extract it and copy recovery.img only to root of your SD Cards
2: download MobileUncleTools for MTK from the attachments and install it as normal apps
3. Now open MobileUncleTools apps you recently installed.
4. grant Superuser permissions
5. There click on recovery update menu
6. Then click on the recovery image name of ‘recovery.img’
7. Let the app install the recovery. after it automatically reboot your device in to recovery
8. now remove battery from device and reinsert it and then reboot device to recovery using volume up + power key
done your TWRP is appears there
Click to expand...
Click to collapse
Screenshots of Mobile uncle tutorials
Click to expand...
Click to collapse
Some SS Tutorials for how to flash CWMR using SP Flash Tools
Click to expand...
Click to collapse
Check here all steps
Click to expand...
Click to collapse
Congrats You have flashed TWRP Recovery v2.4.2.0
Note: If you get any error in SP Flash Tool, then recheck your MTK drivers installation or manually install them through device manager.
Booting into TWRP Recovery v2.4.2.0 is the same as in the stock recovery. Switch on the phone with "Volume Up" and "Power" button Pressed. The Phone will boot into TWRP Recovery v2.4.2.0
I have also attached the the Stock Recovery.zip.
Credit : -
Varun Chitre
yuweng
Cygwin
Me
dont say Thanks Hit
if you can
Click to expand...
Click to collapse
Reverse
Reverse !!
working fine
Wow, very good job.Flashed recovery.img with mobileuncle and everything working fine!
Congratulations ...........:good:
Support for A90?
Sent from my A90 using xda premium
Phone BRICKED
lopestom said:
Wow, very good job.Flashed recovery.img with mobileuncle and everything working fine!
Congratulations ...........:good:
Click to expand...
Click to collapse
Bricked my phone plz HELP Phone Stuck @ Micromax Logo
Abdl said:
Support for A90?
Sent from my A90 using xda premium
Click to expand...
Click to collapse
No......
but soon port it for A90
Recovery Screenshots
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
How to install Clockworkmod Recovery In You Lava Iris N400
Click to expand...
Click to collapse
Make Note :- Posted Screenshots only for Example its not for Lava Iris N400 also download require stuffs first before asking anythings
Click to expand...
Click to collapse
Requirements :-
1. SP Flash Tool + Scatter file from attachments
2. MT65xx VCOM Driver
3. CWMR 6.0.2.8
4. Mobile Uncle Tools ( Optional if u wanna flash recovery those way)
Click to expand...
Click to collapse
Method : SP Flash Tool method, root not required
1. Download MTK6575 Drivers.zip and unzip/extract on your Windows PC, just run InstallDriver.exe to install drivers.
Click to expand...
Click to collapse
2. Download CWM recovery 6.0.2.8 and SP_Flash_Tool_v3.1220.02_FOR_S101A.zip , unzip/extract them.
Click to expand...
Click to collapse
3. Now open extracted SP Flash Tool folder and run Flash_tool.exe
4. Click on "Scatter-loading" button which is on the right side below Downloading Agent. A new window will open. Browse to the extracted CWM recovery 6.0.2.8 folder and select MT6575_Android_scatter.txt file.
5. Flash tool will populate the Map file on the application window. You will see multiple entries. Uncheck all entries except for RECOVERY.
6. Now click on "Download". Warning message will occur, but ignore that and click Yes.
7. You will see in the status bar below "Searching", now connect your phone (with battery inserted + Press and Hold Volume Up Key) via the USB cable.
8. Wait for the process to finish and then you will get a window showing green circle.
Very Easy & safe way to FLASH CWM RECOVERY Without having PC
steps:->
1. Downlaod CWM recovery 6.0.2.8 extract it and rename it to only "" recovery.img"" and copy recovery.img only to root of your SD Cards
2: download MobileUncleTools for MTK from the attachments and install it as normal apps
3. Now open MobileUncleTools apps you recently installed.
4. grant Superuser permissions
5. There click on recovery update menu
6. Then click on the recovery image name of ‘recovery.img’
7. Let the app install the recovery. after it automatically reboot your device in to recovery
8. now remove battery from device and reinsert it and then reboot device to recovery using volume up + power key
done your CWMR is appears there
Click to expand...
Click to collapse
Screenshots of Mobile uncle tutorials
Click to expand...
Click to collapse
Some SS Tutorials for how to flash CWMR using SP Flash Tools
Click to expand...
Click to collapse
Check here all steps
Click to expand...
Click to collapse
Congrats You have flashed CWM recovery 6.0.2.8 !
Note: If you get any error in SP Flash Tool, then recheck your MTK drivers installation or manually install them through device manager.
Booting into CWM recovery 6.0.2.8 is the same as in the stock recovery. Switch on the phone with "Volume Up" and "Power" button Pressed. The Phone will boot into CWM recovery 6.0.2.8 !
I have also attached the the Stock Recovery.zip.
Credit : -
yuweng
Cygwin
Raman Kumar - for testing and giving SS
Me
dont say Thanks Hit
if you can
Click to expand...
Click to collapse
*****Root with SPFT Flash Tool Method*****
for iBerry Auxus One
[EASY ROOT METHOD]
Guys. Now we have our own first Root Method for AUXUS ONE STOCK ROM.
This method is successfully tested by me on Windows 7.
For more help visit this FB page too.
https://www.facebook.com/groups/AuxusOne/
Installation Instructions
Warning: Do at your own risk. Disconnection due to poor cable or Electricity Supply failure can still brick your phone beyond repair. This also breaches warranty of your phone. I am not responsible for any damages.
Disable Antivirus so that it cannot interfere with the flashing process
1) Download flashable zip file named UPDATE-SuperSU-v2.40.zip and save in root of your SDCard
2) Download and extract the Auxus ONE CWM Recovery Flash Package on desktop or anywhere on your pc.
Install Phone Driver (From the Driver folder you have just extracted).
3) Download and Install ADB Driver Installer for Windows (important) while installing connect phone to pc and let is recognize .
After driver installation is done disconnect phone from pc and reboot your pc.
4) Run as Administrator the "Flash_Tool.exe" from SPTools folder inside that folder you extracted.
5) Keep only One File checked (selected) as shown in following image (Recovery.img). If options are not seen then click on "Scatter-loading" button at top-right side and select "One_MT6592_Android_scatter.txt" file from extracted folder. Now be sure only one options (RECOVERY.IMG) selected as mentioned in following image. Unselect all other options.
Now PRESS "Download" button at top.
6) Remove battery and memory card from phone and connect PHONE to pc with usb cable. Now pc should recognize phone and flashing should start in a minute. Look at process bar in image below. WAIT WITH PATIENCE.
After flashing is done, the GREEN tick mark will be shown as shown in image below.
7) Now close program on pc and remove cable, Insert Battery and start phone in RECOVERY mode.
To start phone in recovery mode press "VOLUME UP" button and "POWER" when Auxus Logo appears release "POWER" button keeping "VOLUME UP" button pressed until phone starts in CWM Recovery mode.
8) Important: Now install/flash "UPDATE-SuperSU-v2.40.zip" in Recovery mode and Reboot phone in system (normal) mode
Done. Enjoy Press :good: thanks if you liked my work.
IMPORTANT: The package also contains original Stock Recovery named recovery_org_stock.img. If you want to flash back to original company stock recovery, then select this file in flashing tool (Click recovery line and select this file) and then flash.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Auxus One Unroot Process
For Auxus One Unroot Process Follow the Below Steps
1. Open SuperSu app in your mobile >Setting > Unroot. (Phone will restart and SuperSu & Su binaries will be uninstalled)
2. Flash Stock Recovery by following above root guide from step 1-6 (leave drivers installation part in case drivers are already installed).
3. In above step 5, select recovery_org_stock.img instead of recovery.img file
Thats all, now your phone is unrooted and you can do OTA Update.
Press Thanks button if you like this post!
--- Post reserved for stock recovery process----
fix heating problem help
Dear all pls help me how can i fix heating problem Iberry Auxus One
I have taken the auxus one too , is there any seperate forum for auxus one by any chance ?
rohail009 said:
I have taken the auxus one too , is there any seperate forum for auxus one by any chance ?
Click to expand...
Click to collapse
There is an group for Auxus One on fb for all types of queries, reviews, development related stuff
https://www.facebook.com/groups/AuxusOne/
Kaymart said:
Dear all pls help me how can i fix heating problem Iberry Auxus One
Click to expand...
Click to collapse
Under clock its cpu speed
amarbunty said:
For Auxus One Unroot Process Follow the Below Steps
1. Open SuperSu app in your mobile >Setting > Unroot. (Phone will restart and SuperSu & Su binaries will be uninstalled)
2. Flash Stock Recovery by following above root guide from step 1-6 (leave drivers installation part in case drivers are already installed).
3. In above step 5, select recovery_org_stock.img instead of recovery.img file
Thats all, now your phone is unrooted and you can do OTA Update.
Press Thanks button if you like this post!
Click to expand...
Click to collapse
Hi,
Thanks for your help. But bad news for me. CWM recovery img is not working in my auxus one. even stock img also not working.
Now recovery mode is empty . i cant enter into recovery mode please help me
amarbunty said:
Under clock its cpu speed
Click to expand...
Click to collapse
Please help me. need recovery image to flash. Right now i don't have any recovery mode. Stock recovery is deleted,
Request
Pls any one upload custom rom (MIUI) for iberry auxus one......