Database Info

[GUIDE] How To Use QPST to Change Sprint Banner

I know there are already other threads out there that offer ways to change the sprint banner. I wanted to also offer these set of instructions to the community as I get questions about it all the time. Here is the way I have done it in the past. It does not require HACKED software so this method is fairly safe. As always do a nand back up before going threw these instructions and I can not be held responsible if you brick your phone.
NOTE*** this will break your sprint apps. There is investigation ongoing on getting sprint apps that will work with this mod thanks to DWolf.*** - Workaround thanks to DWolf
1. Install HTC Sync if you haven't already.
2. Download MSL Reader from the market, Run it and save the code for step 8
3. Download QPST:
http://www.x-drivers.com/catalog/flash/mobile_phones/companies/qualcomm/models/qpst/12051.html
4. Install QPST software
5. Put phone into Diag mode: dial ##diag#
6. Start QPST service programming. If your phone is in diag mode you will see it listed here.
7. Click Read from phone
8. Enter your SPC number (the one obtained from step number 2)
9. Click the Display tab.
10. Change the banner to what you want.
11. Write to phone. (You may see some Read Only Errors. This is normal)
12. Reboot phone and you will see the new banner.
Should you encounter issues like the phone not showing up in QPST then more then likely the modem drivers are using a port that QPST does not have as default and you will need to add the port to QPST Configuration. When adding the port to QPST make sure you un-check "Show Serial and USB/QA Diagnostic ports only" or this will not work.
I hope you find this guide helpfull.....

Thanks for this Slayer, as you know, worrked like a charm for me!

Very awesome! I was having trouble with the other methods, this worked perfectly on both my wife and I's phones. Much much thanks to you!

ifly4vamerica said:
Thanks for this Slayer, as you know, worrked like a charm for me!
Click to expand...
Click to collapse
Chris95GT said:
Very awesome! I was having trouble with the other methods, this worked perfectly on both my wife and I's phones. Much much thanks to you!
Click to expand...
Click to collapse
Nice...glad it worked for ya.

What method do i use on the phone to connect? Charge mode, Disk Drive or HTC Sync??

The program wont recognize my phone for some reason..It says in offline mode. I have HTC Sync properly installed and everything

deception88 said:
What method do i use on the phone to connect? Charge mode, Disk Drive or HTC Sync??
Click to expand...
Click to collapse
Well should be in diag mode. But yeah charge would be default.

Hmmmm. I get the Diag up and it says rx:0 and tx:0 but QPST can't find that it is connected... All I get is an option for offline

I have 2 ports COM1 and COM2 and both say unavailable.. Do I try adding one and if so what do i name it? Sorry for all the questions lol

deception88 said:
I have 2 ports COM1 and COM2 and both say unavailable.. Do I try adding one and if so what do i name it? Sorry for all the questions lol
Click to expand...
Click to collapse
Right you need to add the port. It will be the same as com1 or com2 just you will replace the number with what port your phone modem is connecting on. Check this in device manager in control panel of your computer.

Ok got it too work.. I had to install the Diag drivers first then it recognized as a modem. Thanks!

worked perfectly. thanks

Getting error..when i change the banner,write to phone....NV_UE Read only

rob97ss said:
Getting error..when i change the banner,write to phone....NV_UE Read only
Click to expand...
Click to collapse
It still should have changed the banner. Reboot your phone and check. The errors are normal.
Sent from my over modded EVO.

slayer69 said:
It still should have changed the banner. Reboot your phone and check. The errors are normal.
Sent from my over modded EVO.
Click to expand...
Click to collapse
Yes got it..Had to save changes..Thanks.

I AM SO LOST! I HAVE EVERYTHING DOWNLOADED, and even got to DIAG MODE, but don't know how to go from there!

and does the HTC sync have to be on or what? I don't see any relevance? Walk me through?

Also when I unchecked Show serial and USB/DIAG ports only, it won't let me. It says There was an error enabling and port may not be working properly or may be busy.

slayer69 said:
I know there are already other threads out there that offer ways to change the sprint banner. I wanted to also offer these set of instructions to the community as I get questions about it all the time. Here is the way I have done it in the past. It does not require HACKED software so this method is fairly safe. As always do a nand back up before going threw these instructions and I can not be held responsible if you brick your phone.
1. Install HTC Sync if you haven't already.
2. Download MSL Reader from the market, Run it and save the code for step 8
3. Download QPST:
http://www.x-drivers.com/catalog/flash/mobile_phones/companies/qualcomm/models/qpst/12051.html
4. Install QPST software
5. Put phone into Diag mode: dial ##diag#
6. Start QPST service programming. If your phone is in diag mode you will see it listed here.
7. Click Read from phone
8. Enter your SPC number (the one obtained from step number 2)
9. Click the Display tab.
10. Change the banner to what you want.
11. Write to phone. (You may see some Read Only Errors. This is normal)
12. Reboot phone and you will see the new banner.
Should you encounter issues like the phone not showing up in QPST then more then likely the modem drivers are using a port that QPST does not have as default and you will need to add the port to QPST. When adding the port to QPST make sure you un-check "Show Serial and USB/QA Diagnostic ports only" or this will not work.
I hope you find this guide helpfull.....
Click to expand...
Click to collapse
Is there any way to do this on a Linux box?

Sorry... I got it to work now. I made it seem more complicated than it was. Oopsie. THANK YOU SOOO MUCH FOR THIS METHODDDDDDDDDDDDDDD! <3 you!

[Q] CDMA Workshop or the like to make alterations for Nexus S 4G?

Does cdma workshop work with the nexus s? nexus s 4g? looking to get in there and alter what I can...hopefully the eri banner. thank you!!
edit: any other way to get in there would be good too. looking to change the sci, accolc, eri, etc, etc. thanks!

I am looking for the same thing.
If I can get the phone into diag mode, I should be able to get it working.
I am having trouble figuring out how to enter the diag mode.
The normal methods (##Code) doesn't work.

I played with CDMA Workshop earlier after installing EPST and have it not working. It looks like it would need a modified dongle to get the Nexus to enter DL or modem mode as the ## codes don't work. Using all other modes I can't seem to get the program to recognize I have the phone plugged in. I could be missing something but have yet to find anything relevant as a CDMA Nexus is the new crittter on the block.

Update on my previous post, to get the NS4G into D/L mode you hold both volume keys down while pressing the power on button for just a second. Now I just need to find the drivers for this mode.

Got it working!
Here are the steps. I am using Windows 7, I have the Android SDK installed, and Windows update gave me the drivers I need.
1. Make sure USB debugging is off.
2. Dial *#*#8778#*#*
3. Change both settings to Modem.
4. Windows 7 will install your drivers.
5. Add the correct com port, in QPST Config.
6. Open QPST Service Programming, and your all set.

tanman21 said:
Got it working!
Here are the steps. I am using Windows 7, I have the Android SDK installed, and Windows update gave me the drivers I need.
1. Make sure USB debugging is off.
2. Dial *#*#8778#*#*
3. Change both settings to Modem.
4. Windows 7 will install your drivers.
5. Add the correct com port, in QPST Config.
6. Open QPST Service Programming, and your all set.
Click to expand...
Click to collapse
unfortunately, i need the samsung drivers seeing as how my mobile is my web connect.
anyone have the drivers to install??
edit: got it...somehow I found the drivers and got them installed...

tanman21 said:
Got it working!
Here are the steps. I am using Windows 7, I have the Android SDK installed, and Windows update gave me the drivers I need.
1. Make sure USB debugging is off.
2. Dial *#*#8778#*#*
3. Change both settings to Modem.
4. Windows 7 will install your drivers.
5. Add the correct com port, in QPST Config.
6. Open QPST Service Programming, and your all set.
Click to expand...
Click to collapse
got it!
i can view everything in cdma workshop. but when i click 'write', it tells me phone is asking for spc(6 digits). i assume this is my msl which i havent gotten yet for this device...
where do i enter the spc so that i can write changes? thank you!!!
edit: got my msl but i dont think its helping here...my main goal is to alter the sci, which i cant do without cdma workshop, yet. id also like to change the banner but nothing seems to be sticking. thanks for the help!

gotta change the banner, sci...
Last day of classes seems like a good time to tackle this issue.
Gonna continue tinkering around...hopefully we can change the SCI and eri banner(want mine to read 'Google' or 'Nexus S 4G').
Any help would be much appreciated and yield you a wookie life debt. Thank you!!!

Still messing around and I cant seem to find a way to make these alterations. Anyone else have any better luck? Skills?
Thanks!!!

Thanks for the dialer code .. much quicker than decompiling the apk.
I saw references to MSL in this thread and google brought it up as the first result for the ns4g, but no mention of how to obtain it.
For those wondering, getprop | grep MSL will show the MSL. If you don't have busybox installed (for grep), just type getprop after you after root in adb shell or terminal emulator/connectbot and scroll through the list of output, MLS will be in there.
Hope this helps save some time for people! Thanks Samsung and Google for keeping it simple! Thanks for this helpful thread!

when i change them both to modem nothing happens, what do di do when i change them.

with my unrooted s4g, i can access the info in cdma tools. i can connect, read the settings...when i attempt to write changes, sometimes it tells me the phone is requesting the spc. other times it will write certain things and fail writing others..regardless, nothing sticks. frustrating...hopefully i can hold off on rooting again until the 3d comes out...gotta be a way to make it happen without rooting(wishful) or editing eri.xml but if this the only way to make changes to sci, banner, etc; im gonna have to wait until i play with the evo3d...really dont wanna wipe data again

WITH BOTH QPST AND CDMA WORKSHOP, I AM ABLE TO READ THE PHONES SETTINGS BUT I CANT WRITE TO IT. woops, sorry bout the caps.
anyway, when i click write, some things write and others dont. then when i click read, the banner is recognized as google even though it reads sprint on my phone still. often time when i click write in cdma workshop, it tells me phone is requesting spc, spc is required.
update: it seems that the sci and access overload class have stuck to the values that i chose. however, the main goal for me is to alter the banner to read 'Google'.
any input is much appreciated. thank you!

By any chance, are there any tutorials or has anybody successful flashed a Hybrid PRL USING cdma workshop??

Samsung phones such as the Moment and Epic 4g need 'default password' sent to unlock the nvitems to be writeable. Has anyone thought of this or tried this? Maybe the Epic 4g password works?

USB Device Not recognized
Guys i need help i tried everything already!!! My nexus s when i connect the phone to the computer does recognized everything except when i tried to go on modem mode. Do u guys have any clue how to fix this?????

I've been able to flash prl with qpst.
I'm not certain why qpst or the like wouldn't recognize your device.
Sent from my Nexus S 4G via XDA Premium

USB Device Not recognized
it's not the program that is not recognized the phone is my computer that's not recognized my phone on modem mode. i really don't know what's wrong i tried to update the drivers but the computer still no recognizing the phone? what's the procedure that u are taking to get your phone recognized by your computer? (i am using windows xp sp3)

pilussa85 said:
it's not the program that is not recognized the phone is my computer that's not recognized my phone on modem mode. i really don't know what's wrong i tried to update the drivers but the computer still no recognizing the phone? what's the procedure that u are taking to get your phone recognized by your computer? (i am using windows xp sp3)
Click to expand...
Click to collapse
you got the sammy drivers installed? pda net? android usb driver?

yes i did.

How To Fix Phone's IMEI

The following instructions are to be used to repair your G2X/P999 phone's IMEI number if it has been changed to all zeros which can happen due to a bad flash. These instructions are not for any other phone. Your phone's actual IMEI number is printed on the box your phone came in and it is on a sticker located under the battery.
1) Download QPST
http://hosting.ecap-droid.com/Droid/GetFile/20?pf=eMUuB7sRvenLWq&pub=bxfo8sfkv6
2) Install QPST and pin it to the Start Menu
3) Download LG Drivers
http://www.lg.com/us/support-mobile/lg-P999
4) Install LG Drivers
5) In the phone’s Settings -> Applications -> Development -> enable USB debugging
6) Access the phone's hidden menu using the phone keypad (dialer), enter: 1809#*999#
7) In Port Setting enable CP USB (do not enable Retain ...) then press: OK
8) Plug your phone into the USB port and wait a few seconds until the USB drivers install.
9) Access the LGE Mobile USB Modem driver through Control Panel -> Device Manager -> LGE Mobile USB Modem -> Advanced -> Advanced Port Settings
10) Click on the box next to “Append to Log” so that a checkmark is in that box.
11) Click on: Query Modem
The window above “Query Modem” should fill up with (the following data is from my phone, your phone’s Revision may be and IMEI will be somewhat different):
“ATQ0V1E0 - OK
AT+GMM - 0
AT+FCLASS=? - +FCLASS: (0-1)
AT#CLS=? - COMMAND NOT SUPPORTED
AT+GCI? - COMMAND NOT SUPPORTED
AT+GCI=? - COMMAND NOT SUPPORTED
ATI1 - Manufacturer: QUALCOMM INCORPORATED
Model: 0
Revision: M6600A-SCAUTNZ-2.0.9720T 1 [MAR 11 2012 10:00:00] MP:TRULGE_08.09.02R_MDM
IMEI: 0127XXXXXXXXXXXXXXX (I’ve X’d out my IMEI for security reasons)
+GCAP: +CGSM,+DS,+ES
ETC…”
If that doesn’t happen, then the Port Setting has probably reverted back to “AP USB” and will need to be changed back to “CP USB” or the LG drivers didn't install fully or correctly or the computer's usb connection or the usb cable has a problem. Check the phone’s screen and see if the Port Setting is still at “CP USB”. If it’s not (back on “AP USB”) redo step 7. If the setting is still at "CP USB" then reinstall the LG drivers. If there's still a problem, it may be the computer's USB port or the USB cable.
12) Click on: View log
The phone’s current IMEI is listed in the information.
a) If the IMEI is the same as the original one, that means it hasn’t really changed from the original IMEI and it should be OK after the phone is reflashed with a .kdz update file. Flash the phone with a .kdz file by using the offline method.
b) If the IMEI is not the same as the original one, that means it needs to be changed back to the original one.MOD EDIT: IMEI changing is illegal in most countries therefore the instructions to do so cannot be posted on this site. Sorry for the inconvenience

samsung galaxy s2 imei missin
and what about samsung galaxy s2
does that work for it
and what bout the drivers
plz can u help me

I hope I never need this, but glad to know there's a wonderful guide in case I do
Sent from my LG-P999 using xda premium

streethustle said:
and what about samsung galaxy s2
does that work for it
and what bout the drivers
plz can u help me
Click to expand...
Click to collapse
What forum are you in?
Sent via Acer Iconia A100 on CM10_Build090212; godmachine v2.0 kernel, Smooth, Stable, Fast

justjackyl said:
What forum are you in?
Sent via Acer Iconia A100 on CM10_Build090212; godmachine v2.0 kernel, Smooth, Stable, Fast
Click to expand...
Click to collapse
Samsung galaxy s2 - IMEI missing
and i used Hc-ktool to backup the efs but its says efs found in sdcard . nv_data.bin not found ??

Nice guide CoreMemory. Congrats on getting that all together, pretty hetic!
Sent via G2x on temasek b135.2 w/faux kernel v54

justjackyl said:
Nice guide CoreMemory. Congrats on getting that all together, pretty hetic!
Sent via G2x on temasek b135.2 w/faux kernel v54
Click to expand...
Click to collapse
I thought I'd put something useful together because there hasn't been much happening in the G2X forum due to everyone waiting for LG to release the SU660 ICS source code and, hopefully, the results of its application to providing ICS and JB for the G2X.

streethustle said:
and what about samsung galaxy s2
does that work for it
and what bout the drivers
plz can u help me
Click to expand...
Click to collapse
Here's help for you: http://forum.xda-developers.com/showthread.php?t=1264021

Core Memory said:
I thought I'd put something useful together because there hasn't been much happening in the G2X forum due to everyone waiting for LG to release the SU660 ICS source code and, hopefully, the results of its application to providing ICS and JB for the G2X.
Click to expand...
Click to collapse
If everyone was as helpful as you there would be no hunger in the world, no homeless people, etc :good: I hope the knowledge didn't come from firsthand experience:silly:
(PS:best username evar. My last year of undergrad I got to use a System/360 Model 30 with 16k of core memory...the guy in charge was surprised I knew that a "coredump" came from early unix systems having core memory. Yes, he had to smack the memory to fix the bits:victory

The second I change my port setting to CP USB I can't see my LGE MOBILE USB MODEM settings. When I right click it I just get an hour glass.

scsikid said:
The second I change my port setting to CP USB I can't see my LGE MOBILE USB MODEM settings. When I right click it I just get an hour glass.
Click to expand...
Click to collapse
sound like the drivers either aren't installed or not installed properly. Reinstall the LG drivers.

Core Memory said:
sound like the drivers either aren't installed or not installed properly. Reinstall the LG drivers.
Click to expand...
Click to collapse
Ok so I got another laptop, formatted the drive, installed windows 7. Downloaded the drivers you suggested in your first post. Everything went well but now it shows "unknown device" in my device manager. This only happens when CPUSB is enabled. However when APUSB is enabled its fine. So, I guess I need to get this sorted out but am uncertain if there is another driver to install....
Any suggestions..
---------- Post added at 10:55 AM ---------- Previous post was at 10:35 AM ----------
Core Memory said:
sound like the drivers either aren't installed or not installed properly. Reinstall the LG drivers.
Click to expand...
Click to collapse
seems like i have the same problem as blackbeasst
http://forum.xda-developers.com/showthread.php?p=37271515
Core Memory, if you can PM me with some kind of IM chat that you use it would be great. Maybe you can help me more in realtime, or I can let you have access to my PC so you can see the problem I'm facing.

scsikid said:
Ok so I got another laptop, formatted the drive, installed windows 7. Downloaded the drivers you suggested in your first post. Everything went well but now it shows "unknown device" in my device manager. This only happens when CPUSB is enabled. However when APUSB is enabled its fine. So, I guess I need to get this sorted out but am uncertain if there is another driver to install....
Any suggestions..
Click to expand...
Click to collapse
Is your phone setup with "USB debugging" selected? It must be selected.
Do not enable "mass storage".
Then change the port to cpusb and keep the phone on that window.
Then plug the phone into your laptop and wait until all the drivers are loaded. Look at the phone and see if the port mode changed back to APUSB. If it did, change it to CPUSB again and wait for the driver to load.
If that doesn't work, try all of the laptop's usb ports.
If that doesn't work, change the usb cable and try all of the ports again.
This may help:
http://forum.xda-developers.com/showpost.php?p=15899923&postcount=10

Ok, so I tried all of this on two different computers, both running windows 7 64bit. I tried the latest USB driver from LG, uninstalling the old ones from LG. Still the same result, error code 10. Followed the link you provided to re install the driver, same issue.
Anything else?
Core Memory said:
Is your phone setup with "USB debugging" selected? It must be selected.
Do not enable "mass storage".
Then change the port to cpusb and keep the phone on that window.
Then plug the phone into your laptop and wait until all the drivers are loaded. Look at the phone and see if the port mode changed back to APUSB. If it did, change it to CPUSB again and wait for the driver to load.
If that doesn't work, try all of the laptop's usb ports.
If that doesn't work, change the usb cable and try all of the ports again.
This may help:
http://forum.xda-developers.com/showpost.php?p=15899923&postcount=10
Click to expand...
Click to collapse

scsikid said:
Ok, so I tried all of this on two different computers, both running windows 7 64bit. I tried the latest USB driver from LG, uninstalling the old ones from LG. Still the same result, error code 10. Followed the link you provided to re install the driver, same issue.
Anything else?
Click to expand...
Click to collapse
copy and paste this C:\Windows\system32\DRIVERS\ into your browser and press enter.
Is lgusbdiag.sys in C:\Windows\system32\DRIVERS\
Download lgusbdiag.sys from http://www.sysfreedownload.com/DownSoft/?softid=2020&pathid=0
Unzip it.
Right-click on the unzipped file and access properties and unblock it.
Install it in C:\Windows\system32\DRIVERS\
and, if lgusbdiag.sys is already in there, let it overwrite the file.
Reboot
Plug the G2X into your computer, etc.

Open Device Manager -> Ports (COM & LPT)
Is there a port named: LGE Mobile USB Serial Port

Core Memory said:
Open Device Manager -> Ports (COM & LPT)
Is there a port named: LGE Mobile USB Serial Port
Click to expand...
Click to collapse
Nah didn't work. Went to a command prompt with administrative privileges, copied the file you suggested. Rebooted and plugged in my phone, still nothing. Just shows the LGE Mobile Composite USB Device driver under USB that I had to force the installation of.
Nothing under com ports or modems.
I also tried this on windows xp and it didnt work.

scsikid said:
Nah didn't work. Went to a command prompt with administrative privileges, copied the file you suggested. Rebooted and plugged in my phone, still nothing. Just shows the LGE Mobile Composite USB Device driver under USB that I had to force the installation of.
Nothing under com ports or modems.
I also tried this on windows xp and it didnt work.
Click to expand...
Click to collapse
Is this in the Registry:
HKEY_LOCAL_MACHINE\SYSTEM\ControlSet002\Control\Class\{4D36E978-E325-11CE-BFC1-08002BE10318}/36
DriverDesc/LGE Mobile USB Serial Port
DriverVersion/4.9.8.1
MatchingDeviceId/usb\vid_1004&pid_6000_diaginterface
NTMPDriver/lgusbdiag.sys
ProviderName/LG Electronics Inc.

Core Memory said:
Is this in the Registry:
HKEY_LOCAL_MACHINE\SYSTEM\ControlSet002\Control\Class\{4D36E978-E325-11CE-BFC1-08002BE10318}/36
DriverDesc/LGE Mobile USB Serial Port
DriverVersion/4.9.8.1
MatchingDeviceId/usb\vid_1004&pid_6000_diaginterface
NTMPDriver/lgusbdiag.sys
ProviderName/LG Electronics Inc.
Click to expand...
Click to collapse
In windows 7 it is not there. Should it be on WindowsXP? I assume both.
If this is what I need, how do I add it?

scsikid said:
In windows 7 it is not there. Should it be on WindowsXP? I assume both.
If this is what I need, how do I add it?
Click to expand...
Click to collapse
Yes, both are the same.
That means the driver didn't load. There's something wrong with the driver loading.
Manually installing the drivers may work. After you connect the G2X via USB then set the port to CP USB, what happens? Is there any beeping from the laptop? Does a yellow triangle with an exclamation mark appear in Device Manager -> Ports (COM & LPT)?

How to Root Samsung Galaxy S Relay 4G [WITH VIDEO AND VOICE TUTORIAL]

***ONLY FOR RELAYS RUNNING ICS 4.0.4***​
Samsung had just released the official Jelly Bean 4.1 update for this phone on April 22 or so and this root method only works for Ice Cream Sandwich devices.
I know there's already a thread of how to root the ICS Samsung Galaxy S Relay 4G which is right here: http://forum.xda-developers.com/showthread.php?p=34515281 but I thought that it may be hard for some people to do it without a visual tutorial. Here's my helpful tutorial video of how to root the Samsung Galaxy S Relay 4G: https://plus.google.com/u/0/108388305247615258469/videos <-- You can easily find the video because it's the only video on that album.
Files Needed:
Winrar: http://www.win-rar.com/download.html?&L=0
Odin v3.07: http://www.4shared.com/zip/CGo6TP1O/Odin307.html? or for the latest and updated versions: http://forum.xda-developers.com/showthread.php?t=1738841
Rooted System IMG: http://www.4shared.com/rar/nhGK59WR/SGHT699_rootedtar.html?
CWM File: http://www.4shared.com/zip/wLHTlktW/cwmtar.html?
If none of the links above work, message me at [email protected] or reply to this topic and I will reupload the files.
Steps:
1) On your phone, go to Settings-->Developer Options and turn on USB Debugging.
2) Turn off your phone and put it in Download Mode/Odin mode.
3) Download the odin307, sght699_rooted.tar, and that cwm.tar files from the links given above.
4) Extract all the files with WinRAR or other file extracting programs.
5) Open Odin v3.07
6) Make sure that it says "Added!" on the bottom left box. If it doesn't say Added, unplug and plug your phone from the computer.
7) Deselect/Uncheck "Auto Reboot" and "F. Reset Time"
8) Click on Phone and a pop up should come up.
9) Find the SGHT699_rooted folder that you extracted in Step 4 and open the file inside it.
10) Click Start. This will take a while but it should not take more than 14 minutes.
11) Once it's done, click Reset.
12) Unplug and plug your phone again. It should say "Removed!" when unplugged and "Added!" when plugged on the bottom left box.
13) Deselect/Uncheck "F. Reset Time" but this time, keep the "Auto Reboot" marked/checked.
14) Click on PDA and a popup should come up.
15) Find the cwm folder that you extracted in Step 4 and open the cwm.tar.md5 file.
16) Click Start.
Once it finishes, your phone should reboot and be rooted. To check if it is actually rooted, go on Applications and find Superuser. If it is there, then you are rooted. Enjoy!!

Very nice. You are missing information, need to add the original posts/threads for the files that you mirrored so we can get version numbers and dates associated with the downloads. Feel free to edit the wiki in my sig if you want to help!

Ok. Thanks, but there's a problem. The files I mirrored other than Odin v3.07 are gone. The original link where the original tutorial was is gone. I had the link in my bookmarks but when I click on it, the webpage is unavailable. Ive tried viewing it from other computers and devices and it still wont work. So I decided to make a new one. Thanks again! The links should be updated in a few.
Sent from my SGH-T699 using xda app-developers app

Thanks.
Version is UVAMA2?
Sent from my SGH-T699 using xda premium

XIAOSpider said:
Thanks.
Version is UVAMA2?
Sent from my SGH-T699 using xda premium
Click to expand...
Click to collapse
What's UVAMA2?

USB won't connect properly; want to un-root
You're rooting video was very helpful.
However, now that the phone is rooted, when I try to connect to my computer with USB cable, I get error message to the effect that the computer can't recognize the hardware ID of the device, so can't back-up the files on the phone or the SD card. I have all the latest Samsung USB drivers, and the computer recognizes that a Samsung device is connected, but the USB connection fails anyway.
How do I un-root the phone - do I have to boot up in download mode and use ODIN? Will this wipe my data, or just go back to the unrooted ROM and keep my data intact?
-----------
Chrizuki said:
I know there's already a thread of how to root the Samsung Galaxy S Relay 4G which is right here: http://forum.xda-developers.com/showthread.php?p=34515281 but I thought that it may be hard for some people to do it without a visual tutorial. Here's my helpful tutorial video of how to root the Samsung Galaxy S Relay 4G: http://www.youtube.com/watch?v=GKgemJTeRWo
Files Needed:
Winrar: http://www.win-rar.com/download.html?&L=0
Odin v3.07: http://www.4shared.com/zip/CGo6TP1O/Odin307.html? or for the latest and updated versions: http://forum.xda-developers.com/showthread.php?t=1738841
Rooted System IMG: http://www.4shared.com/rar/nhGK59WR/SGHT699_rootedtar.html?
CWM File: http://www.4shared.com/zip/wLHTlktW/cwmtar.html?
If none of the links above work, message me at [email protected] or reply to this topic and I will reupload the files.
Steps:
1) On your phone, go to Settings-->Developer Options and turn on USB Debugging.
2) Turn off your phone and put it in Download Mode/Odin mode.
3) Download the odin307, sght699_rooted.tar, and that cwm.tar files from the links given above.
4) Extract all the files with WinRAR or other file extracting programs.
5) Open Odin v3.07
6) Make sure that it says "Added!" on the bottom left box. If it doesn't say Added, unplug and plug your phone from the computer.
7) Deselect/Uncheck "Auto Reboot" and "F. Reset Time"
8) Click on Phone and a pop up should come up.
9) Find the SGHT699_rooted folder that you extracted in Step 4 and open the file inside it.
10) Click Start. This will take a while but it should not take more than 14 minutes.
11) Once it's done, click Reset.
12) Unplug and plug your phone again. It should say "Removed!" when unplugged and "Added!" when plugged on the bottom left box.
13) Deselect/Uncheck "F. Reset Time" but this time, keep the "Auto Reboot" marked/checked.
14) Click on PDA and a popup should come up.
15) Find the cwm folder that you extracted in Step 4 and open the cwm.tar.md5 file.
16) Click Start.
Once it finishes, your phone should reboot and be rooted. To check if it is actually rooted, go on Applications and find Superuser. If it is there, then you are rooted. Enjoy!!
Click to expand...
Click to collapse

nosch454 said:
You're rooting video was very helpful.
However, now that the phone is rooted, when I try to connect to my computer with USB cable, I get error message to the effect that the computer can't recognize the hardware ID of the device, so can't back-up the files on the phone or the SD card. I have all the latest Samsung USB drivers, and the computer recognizes that a Samsung device is connected, but the USB connection fails anyway.
How do I un-root the phone - do I have to boot up in download mode and use ODIN? Will this wipe my data, or just go back to the unrooted ROM and keep my data intact?
-----------
Click to expand...
Click to collapse
Oops, sorry. Forgot the part of your reply that said you've installed all the drivers. What do you mean by it can't recognize it? Does the SGH-T699 still show up on your My Computer?
If you want to unroot, go here: http://forum.xda-developers.com/showthread.php?t=2166242
Just follow the steps and no, it won't wipe out all your data (Well, it didn't wipe mine, but I'm sure it won't.)
Sent from my SGH-T699 using xda app-developers app

Problems connecting with USB (MTP driver install failure)
Chrizuki said:
Oops, sorry. Forgot the part of your reply that said you've installed all the drivers. What do you mean by it can't recognize it? Does the SGH-T699 still show up on your My Computer?
If you want to unroot, go here: http://forum.xda-developers.com/showthread.php?t=2166242
Just follow the steps and no, it won't wipe out all your data (Well, it didn't wipe mine, but I'm sure it won't.)
Sent from my SGH-T699 using xda app-developers app
Click to expand...
Click to collapse
When I connect the USB cable, Windows has a popup message that says:
" Hardware ID missing
Windows cannot identify the device plugged into the Samsung Mobile USB Composite Device.
For assistance, contact the hardware manufacturer"
Sometimes it tries - and fails - to install the MTP device driver.
However, when I go into Windows Device Manage, it does list SAMSUNG Android Phone | SAMSUNG Android ADB Interface, and when trying to update its drivers, it says I have the most up to date ones installed.
- What does "Hardware ID missing" mean? How do I get the phone to communicate with the computer using USB?
I thought it might have to do with Android Ice Cream Sandwich and the media device (MTP) protocol for USB, but, I had no problems getting the computer to recognize my son's (unrooted) Galaxy S 3, which also has ICS and is pretty similar to the Galaxy S Relay 4G. That's why I suspect the problem is with my rooted version.
Is there anything else I should try before un-rooting the phone?

nosch454 said:
When I connect the USB cable, Windows has a popup message that says:
" Hardware ID missing
Windows cannot identify the device plugged into the Samsung Mobile USB Composite Device.
For assistance, contact the hardware manufacturer"
Sometimes it tries - and fails - to install the MTP device driver.
However, when I go into Windows Device Manage, it does list SAMSUNG Android Phone | SAMSUNG Android ADB Interface, and when trying to update its drivers, it says I have the most up to date ones installed.
- What does "Hardware ID missing" mean? How do I get the phone to communicate with the computer using USB?
I thought it might have to do with Android Ice Cream Sandwich and the media device (MTP) protocol for USB, but, I had no problems getting the computer to recognize my son's (unrooted) Galaxy S 3, which also has ICS and is pretty similar to the Galaxy S Relay 4G. That's why I suspect the problem is with my rooted version.
Is there anything else I should try before un-rooting the phone?
Click to expand...
Click to collapse
Install kies or the USB driver directly from samsung.com. Try the USB driver first, then kies if it doesn't work.

Nocturin said:
Install kies or the USB driver directly from samsung.com. Try the USB driver first, then kies if it doesn't work.
Click to expand...
Click to collapse
Already tried both. USB driver is OK, the problem is with MTP. Kies only works via WiFi; does not recognize device with USB. I also tried Samsung tech support's suggestions, none of which changed the situation

nosch454 said:
Already tried both. USB driver is OK, the problem is with MTP. Kies only works via WiFi; does not recognize device with USB. I also tried Samsung tech support's suggestions, none of which changed the situation
Click to expand...
Click to collapse
Have you tried downloading the SDK Manager from "http://developer.android.com/sdk/index.html"? Open the big file that you just downloaded and open up SDK Manager. Install the Google USB Driver and as well as the Android SDK Tools and Android SDK Platform-tools. Once downloaded, go back to the android-sdk-windows folder and go to the "platform-tools" folder inside and hold Shift and right click on "adb" and select "Open Command Window Here" of something like that. The command prompt will open. Type in "adb devices" and tell me what comes up. If you see your device(It should be a bunch on numbers and letters) on there, it means it is recognizable. This might not solve your problem as I do not know what "Hardware ID missing" exactly is. But I will do some research.

I did as you suggested, and was able to see my phone when I ran "adb devices" from the command prompt. And, Windows, recognizes it too, because when I click on the button to remove attached USB devices, it lists SAMSUNG_Android_SGH-T699. But, I still get the hardware ID missing message whenever I connect the USB cable. Frustrating! But, thanks for trying to help me - you seem very knowledgeable.

What you can try and do to fix the USB hardware error is go to control panel then go to "uninstall a program" and uninstall the samsung driver once you uninstalled it reconnect your phone and let it reinstal the files and i believe it should fix your problem

Samsung Noob here with a question.
Ok, I know this is gonna sound kinda noobish, but I come from HTC phones, and this is my first Samsung. Do I need to flash ClockworkMod Recovery on this, or do I flash a rom to the 4G Relay using Odin? If I use Odin, can someone give a quick overview on how?

Gh0sTly said:
Ok, I know this is gonna sound kinda noobish, but I come from HTC phones, and this is my first Samsung. Do I need to flash ClockworkMod Recovery on this, or do I flash a rom to the 4G Relay using Odin? If I use Odin, can someone give a quick overview on how?
Click to expand...
Click to collapse
you'll need to install a recovery as you did on HTC as ROMs usually come as recovery-flashable zips.
there's a cwm recovery available here which can flashed using Odin. If you don't like the cwm on the relay you can flash TWRP from cwm over it. TWRP comes with more options and the touchscreen-control you might be used to.
from (any) recovery you can just install update zip-files just as you used to on your HTC.

I had used the "howto root the Galaxy S Relay" thread, and then realized, I should just SU and reboot recovery. :victory:

nosch454 said:
I did as you suggested, and was able to see my phone when I ran "adb devices" from the command prompt. And, Windows, recognizes it too, because when I click on the button to remove attached USB devices, it lists SAMSUNG_Android_SGH-T699. But, I still get the hardware ID missing message whenever I connect the USB cable. Frustrating! But, thanks for trying to help me - you seem very knowledgeable.
Click to expand...
Click to collapse
If anybody else got this error do the following:
- uninstall all samsung drivers / software
- connect your phone to the pc
- the driver installation should 'fail', but you can access the storage
- install the samsung drivers now while phone is plugged in
After the installation the phone will be recognized and everything is fine - this worked twice for me now, so I guess it should do it.

Flashing Nexus 5 (D820) into your own CDMA carrier

This is just a small guide on how to flash Nexus 5 D820 (US version) from Sprint to other CDMA carriers. Please mind that this is a trial and error guide which I tried many times before I succeeded flashing my Nexus 5. So if there are some mistakes that needed to be corrected , please tell me and I won't mind .
So let's begin: First, you need to root your Nexus 5. I will not provide on how to root it since there are lots of guides out there if you google it. Ok, after that you need to install the Nexus 5 Windows driver which you can download it from here: http://drivers.softpedia.com/get/MOBILES/LG/LG-United-Mobile-Driver-381.shtml
Since LG Nexus 5 doesn't have dial code for diag mode we have to flash diag mode boot img file which you can download from here: http://forum.xda-developers.com/attachment.php?attachmentid=2421929&d=1385715923
You can use Flashify which can be downloaded from Google Play Store to flash the img file. The phone will reboot after you flash it.
Ok, after all that you can connect the Nexus 5 to the pc/notebook using the usb data cable. Usually Windows will automatically install all the drivers for the Nexus 5 once you connect it. Oh, don't forget to enable the USB debugging mode from the developer options menu.
After all the needed drivers have been installed, we will enter the rather complicated on how to use adb shell command. You all can read the guides here: http://forum.xda-developers.com/showthread.php?t=2514396
There will be SDK Tools which you have to download for Windows. The guide will tell you all on how to install it.
For the flashing tools, we need:
1) CDMA Workshop 3.9
2) DFS tools
3) QPST
All these tools you have to find/buy them by your own since I can't provide them. Sorry.
Ok let's enter into diag mode. Go into command prompt window and type:
adb shell
then type:
su
(here the $ sign will change into #)
and then type:
setprop sys.usb.config diag,adb
Ok we should be in diag mode now. We will use CDMA workshop first. Set the port. and then click connect. We will find the SPC code and change it. Go into the security tab. In SPC/user lock , let's change the Default (NV_read) into LG method. and click read. We will see some numbers in the box. We will click the SPC button now, there will be a writing like this: Write "000000". Choose that. And SPC code has been changed from those confusing numbers into simple numbers 000000. We succeeded unlocking the SPC. Click reset on the right top corner (it looks like reload button). After that reboot your Nexus 5.
Get into diag mode again. Open your CDMA Workshop again. Connect. Get into memory tab. Go into NV-items. Write nv-item which you can download from: http://www.cricketusers.com/sprint-lg-optimus-s/16145-optimus-s-cdma-ws-3-x-nv-items.html
Ok choose reset and then reboot your phone again.
Get into diag mode again as usual. We will use DFS software now. Choose port. Connect. And click SPC which usually written down 000000. It will unlock the phone so we can write down settings into it. All right in here go to Programming tab where you need to enter all your MDN, MIN, Akey, PRL, etc informations which you can get from your own carriers/operators. If using DFS is confusing, please read the guide first. I am sure you can find some in google .
Ok if everything is written and you press reset on DFS. Reboot your phone. Usually after this you can use your phone for calling and sending SMS text. Oh, don't forget to insert a simcard in your phone. Usually just put a GSM card. This phone can be used for either CDMA or GSM. There will be a new menu in mobile network. LTE-3G-1x-Global(GSM).
But the 3G EVDO for data connection will not work at this stage. So we will use QPST software. Use the latest QPST software 2.7 built. Connect and as usual you have to enter SPC code. Go into PPP config tab. There you will go into Um tab. Check if our user id is the same as the user id as given by your own carrier or is it still filled by Sprint's user id? If the Sprint's id is still written there, go into the user id box and press ctrl-d from your keyboard to wipe the Sprint's ID. And then do the same thing in AN tab. After all that, press write to phone. Reboot your Nexus 5.
Get into the diag mode again...hope you guys don't get tired of it though :laugh: Open QPST, read from your phone, get into PPP config. Go into Um tab and the user id box should be empty now. Fill it with your user id and password too. And do the same thing in AN tab. Go into M.IP tab and check if profile 1 (ignore profile 0) is enable. get into it and check if both NAI and Tethered NAI are written with our own user id. Write to phone and reboot your phone.
We will wait for a few minutes......and usually 3G EVDO sign will come up. Go into About Phone, take a look in Status is it written: CDMA-Evdo rev. A....if it is congrats, you have successfully flash your phone with your own carrier. :laugh:
Hopefully this guide will help you guys. I know it's a bit confusing. Hey it's my first time writing a guide....If there's any mistake that I made, please don't hesitate to tell me. Thanks guys.

hendrali said:
This is just a small guide on how to flash Nexus 5 D820 (US version) from Sprint to other CDMA carriers. Please mind that this is a trial and error guide which I tried many times before I succeeded flashing my Nexus 5. So if there are some mistakes that needed to be corrected , please tell me and I won't mind .
So let's begin: First, you need to root your Nexus 5. I will not provide on how to root it since there are lots of guides out there if you google it. Ok, after that you need to install the Nexus 5 Windows driver which you can download it from here: http://drivers.softpedia.com/get/MOBILES/LG/LG-United-Mobile-Driver-381.shtml
Since LG Nexus 5 doesn't have dial code for diag mode we have to flash diag mode boot img file which you can download from here: http://forum.xda-developers.com/attachment.php?attachmentid=2421929&d=1385715923
You can use Flashify which can be downloaded from Google Play Store to flash the img file. The phone will reboot after you flash it.
Ok, after all that you can connect the Nexus 5 to the pc/notebook using the usb data cable. Usually Windows will automatically install all the drivers for the Nexus 5 once you connect it. Oh, don't forget to enable the USB debugging mode from the developer options menu.
After all the needed drivers have been installed, we will enter the rather complicated on how to use adb shell command. You all can read the guides here: http://forum.xda-developers.com/showthread.php?t=2514396
There will be SDK Tools which you have to download for Windows. The guide will tell you all on how to install it.
For the flashing tools, we need:
1) CDMA Workshop 3.9
2) DFS tools
3) QPST
All these tools you have to find/buy them by your own since I can't provide them. Sorry.
Ok let's enter into diag mode. Go into command prompt window and type:
adb shell
then type:
su
(here the $ sign will change into #)
and then type:
setprop sys.usb.config diag,adb
Ok we should be in diag mode now. We will use CDMA workshop first. Set the port. and then click connect. We will find the SPC code and change it. Go into the security tab. In SPC/user lock , let's change the Default (NV_read) into LG method. and click read. We will see some numbers in the box. We will click the SPC button now, there will be a writing like this: Write "000000". Choose that. And SPC code has been changed from those confusing numbers into simple numbers 000000. We succeeded unlocking the SPC. Click reset on the right top corner (it looks like reload button). After that reboot your Nexus 5.
Get into diag mode again. Open your CDMA Workshop again. Connect. Get into memory tab. Go into NV-items. Write nv-item which you can download from: http://www.cricketusers.com/sprint-lg-optimus-s/16145-optimus-s-cdma-ws-3-x-nv-items.html
Ok choose reset and then reboot your phone again.
Get into diag mode again as usual. We will use DFS software now. Choose port. Connect. And click SPC which usually written down 000000. It will unlock the phone so we can write down settings into it. All right in here you need to enter all your MDN, MIN, Akey, PRL, etc informations which you can get from your own carriers/operators. If using DFS is confusing, please read the guide first. I am sure you can find some in google .
Ok if everything is written and you press reset on DFS. Reboot your phone. Usually after this you can use your phone for calling and sending SMS text. Oh, don't forget to insert a simcard in your phone. Usually just put a GSM card. This phone can be used for either CDMA or GSM. There will be a new menu in mobile network. LTE-3G-1x-Global(GSM).
But the 3G EVDO for data connection will not work at this stage. So we will use QPST software. Use the latest QPST software 2.7 build 422. Connect and as usual you have to enter SPC code. Go into PPP config tab. There you will go into Um tab. Check if our user id is the same as the user id as given by your own carrier or is it still filled by Sprint's user id? If the Sprint's id is still written there, go into the user id box and press ctrl-d from your keyboard to wipe the Sprint's ID. And then do the same thing in AN tab. After all that, press write to phone. Reboot your Nexus 5.
Get into the diag mode again...hope you guys don't get tired of it though :laugh: Open QPST, read from your phone, get into PPP config. Go into Um tab and the user id box should be empty now. Fill it with your user id and password too. And do the same thing in AN tab. Go into M.IP tab and check if profile 1 (ignore profile 0) is enable. get into it and check if both NAI and Tethered NAI are written with our own user id. Write to phone and reboot your phone.
We will wait for a few minutes......and usually 3G EVDO sign will come up. Go into About Phone, take a look in Status is it written: CDMA-Evdo rev. A....if it is congrats, you have successfully flash your phone with your own carrier. :laugh:
Hopefully this guide will help you guys. I know it's a bit confusing. Hey it's my first time writing a guide....If there's any mistake that I made, please don't hesitate to tell me. Thanks guys.
Click to expand...
Click to collapse
ok nice info. can u clarify ll flashing clears all apps & phone ? need to take backup ? probably a noob question.

No, it will not wipe out any of your app. But you are welcome to backup your phone first
Sent from my Nexus 5 using XDA Premium 4 mobile app

hendrali said:
No, it will not wipe out any of your app. But you are welcome to backup your phone first
Sent from my Nexus 5 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
is cdma workshop must ? coz i dont have or cant buy it. dfs itselfs allows read & write of spc.
getting PRL is also prob. tried cant find for cdma service provider. any other option ?
---------- Post added at 08:20 PM ---------- Previous post was at 07:29 PM ----------
madroamer said:
is cdma workshop must ? coz i dont have or cant buy it. dfs itselfs allows read & write of spc.
getting PRL is also prob. tried cant find for cdma service provider. any other option ?
Click to expand...
Click to collapse
i flashed the device. i can see nexus 5 under devices in ddevice manager. all drivers installed. no issue.
i opened command prompt and type adb shell... den su...
wen i type setprop sys.usb.config diag,adb nexus 5 disappears in devices but doesnt show in any ports ...!!!!!!! y so ? how to rectify this

Hi could you please clarify me what do you get when doing this operation? I was looking into a way to use 4g in Europe from the nexus 5 d820 version, since here the channels used are not supported by this version. I suppose this tutorial doesn't have anything to do with the lte channels é hehe.
Thx
Sent from my Nexus 10 using Tapatalk

Hey,
Very nice detailed guide, I'm sure it will help a lot of people looking to flash their N5s.
Thanks.
Sent from my Nexus 5 using Tapatalk

leonux said:
Hi could you please clarify me what do you get when doing this operation? I was looking into a way to use 4g in Europe from the nexus 5 d820 version, since here the channels used are not supported by this version. I suppose this tutorial doesn't have anything to do with the lte channels é hehe.
Thx
Sent from my Nexus 10 using Tapatalk
Click to expand...
Click to collapse
Sorry this guide is only for flashing CDMA.

madroamer said:
is cdma workshop must ? coz i dont have or cant buy it. dfs itselfs allows read & write of spc.
getting PRL is also prob. tried cant find for cdma service provider. any other option ?
---------- Post added at 08:20 PM ---------- Previous post was at 07:29 PM ----------
i flashed the device. i can see nexus 5 under devices in ddevice manager. all drivers installed. no issue.
i opened command prompt and type adb shell... den su...
wen i type setprop sys.usb.config diag,adb nexus 5 disappears in devices but doesnt show in any ports ...!!!!!!! y so ? how to rectify this
Click to expand...
Click to collapse
Ok for the SPC try this app which u can download from here: http://forum.xda-developers.com/showthread.php?t=2394499
I haven't tried it yet, but I hope it will work for you. Read the SPC first and then write 000000. Hope it helps. As for the PRL, you have to have it or else it will not work. Ask your carrier/operator or search it in Google.
And for the adb shell....what happen when u type su? does the $ sign change into # sign?

hendrali said:
Ok for the SPC try this app which u can download from here: http://forum.xda-developers.com/showthread.php?t=2394499
I haven't tried it yet, but I hope it will work for you. Read the SPC first and then write 000000. Hope it helps. As for the PRL, you have to have it or else it will not work. Ask your carrier/operator or search it in Google.
And for the adb shell....what happen when u type su? does the $ sign change into # sign?
Click to expand...
Click to collapse
s boss it does change to $ sign. den only typed the code...i cant get in ports

hendrali said:
Use the latest QPST software 2.7 build 422.
Click to expand...
Click to collapse
Hello, fellow QPST users.
QPST 2.7 Build 4.2.2 is a fake version with keylogger.
Some a$$hole downloaded latest public QPST build (4.0.2) and decompiled MSI installer package, then edited all "4.0.2" to "4.2.2", added "fake changelog", added keylogger (qualcomm.exe), then repackaged and spread around web!
Everyone who downloaded QPST build "4.2.2" should change all his passwords.
More info about malware from fake 4.2.2 build (QPST.2.7.422.msi)
MSI package (QPST.2.7.422.msi) was embedded/tampered with qualcomm.exe which is a .NET based malware that logs your keystrokes and sends it to attacker's server.
How to delete the actual malware from your system?
Look at the startup from msconfig or CCleaner, there should be a file called qualcomm.exe thats set to start everytime system starts. Delete both registry and file.
If you wanted to see what data thief was stolen from you. Just open the .dc file (in "dclogs" folder) with Notepad and see for yourself.
In XP, dc file is located here!
C:\Documents and Settings\Administrator\Application Data\dclogs
there should be a file called "201X-XX-XX-X.dc
if you open that DC files with Notepad, you'll see all your keystrokes.
Here is mine. I've intentionally entered paypal site with fake info.
:: Run (3:01:51 AM)
Script kiddie. NET Based malware, huh?[ESC]
:: Program Manager (3:02:14 AM)
e
:: Firefox (3:02:18 AM)
www.paypal.com
[email protected][TAB]
mypaypalpass
[ENTER]
:: Documents and Settings (3:02:19 AM)
[UP]
:: Administrator (3:02:28 AM)
[DOWN][DOWN][DOWN][DOWN][DOWN][DOWN][DOWN][DOWN][DOWN][DOWN]
[DOWN][DOWN][DOWN][DOWN][DOWN][DOWN][DOWN][DOWN][DOWN][DOWN][DOWN][DOWN][DOWN]
d
:: (3:02:34 AM)
:: Administrator (3:02:34 AM)
d
:: (3:03:11 AM)
mmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmm
:: [Release] QPST 2.7 BUILD 422 - Download Here - Enjoy - Mozilla Firefox (3:03:57 AM)
crap
How to delete?d
:: Clipboard Change : size = 16 Bytes (3:03:57 AM)
QPST.2.7.422.msi
:: (3:04:23 AM)
cccccc
Click to expand...
Click to collapse
Keylogger sends the logs from keylogger to "qpst.hopto.me"
So please report about this incident where and when you encounter QPST 4.2.2 somewhere (forums, posts, sharing-sites, etc)
Copy my whole post and paste it where you see 4.2.2 mentioned.
Bonus: Fake Changelog
If you've installed this 422 build, then open the Readme.txt in C:\Program Files\Qualcomm\QPST\Documents
Scroll down and see the "6/12/13 QPST 2.7.422 changelog"
6/12/13 QPST 2.7.422
1) EFS Hello commands will not be sent unless the device is in a compatible mode. Sending this command when the
device is in download mode can cause a "server busy" message for a few seconds because of command retries.
2) Support for the Sahara device protocol (see 80-N1008-1 or equivalent) is now built in to the QPST server process.
This protocol is only supported by USB Serial ports, not TCP/IP connections. In QPST Configuration a device in
this mode will display as "Q/QCP-XXX (Sahara Download)". This mode can only be detected (1) when the QPST server
process starts or a COM port in this mode added to QPST, or (2) when a device enters Sahara mode on a port assigned
to QPST. This is because the device only sends its Hello message once, as soon as the COM port is opened.
Click to expand...
Click to collapse
Changelog above is actually cloned from QPST 2.7.394 Just scroll down and see Build 2.7.394 changelog. Its same!
So forget about Build 422. It doesn't exist.
Use QPST 2.7 Build 402. It's the latest public build
Sorry about my english
Best Regards
AnycallMongolia

Ok. Thanks for giving this info about the QPST 4.2.2. I didn't know it was a fake one. Luckily i checked mine didn't have the virus. I guess someone cleaned up the version that i downloaded somehow.
Sent from my Nexus 5 using XDA Premium 4 mobile app

hendrali said:
Ok. Thanks for giving this info about the QPST 4.2.2. I didn't know it was a fake one. Luckily i checked mine didn't have the virus. I guess someone cleaned up the version that i downloaded somehow.
Sent from my Nexus 5 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
Uh, no! You've just been told it's a fake. Get the official one until told otherwise would be my recommendation

Yup i guess so. I will download the latest official release then. I will edit my post so no one will download the fake one.
Sent from my Nexus 5 using XDA Premium 4 mobile app

Flashing My N5 To Boost (maybe...lol)
I really want to flash mine to Boost but I since I only want to do one phone I don't want to purchase CDMA workshop to do it and the free edition (2.7) lets you get the SPC but won't let me write the NV items. Is there another program that will let me write the NV items, one that doesn't cost $100
Also, I want to flash mine to Boost Mobile and wondered if anyone out there has done it and succeeded. I sent mine to a phone flasher and at first he said he could do it then sent it back telling me he couldn't. So I paid $360 for a phone thats just sitting there...LOL

s me too waiting for a s/w free to use to write NV & misc

Did u guys try this one yet? http://forum.xda-developers.com/showthread.php?t=2394499
Sent from my Nexus 5 using XDA Premium 4 mobile app

no new port or lg.... shows in com/port in device manager
wat is the reason ?
device is otherwise fine with response to commands...
using windows 8. pl help

i even tried in win 7. after type setprop ... no change...no new port opens...
tried for so many time...some one help to identify issue

This is AWESOME news!!! Now I do have one question... If we were to flash the N5 to our carrier (nTelos in this case) and I put in my LTE sim card, will it activate on LTE, or will it only work with the 3G CDMA portion? - I know that with the nTelos iPhones, they can be activated on standard CDMA and work on 3G, then when you insert a sim card, it updates the carrier settings automatically, and it starts working on LTE. Is that the same case here?

EddyOS said:
Uh, no! You've just been told it's a fake. Get the official one until told otherwise would be my recommendation
Click to expand...
Click to collapse
where?
Whe last I looked all I found was on forums like XDA.?
BTW there's a post somewhere (can;t remeber exactly, it's either Nexu 5 or 4 or some other LG phones forum ) that shows you how to get the SPC,
resign all the APK that come with the blobs
OmaDmclient.apk,SprintHiddenMenu.apk,Term.apk,TimeService.apk,UpdateSetting.apk,qcrilmsgtunnel.apk,shutdownlistener.apk
with the platform key (if on stock rom no need anything else AOSP based you have to resign then with the platform key which is the testkey -the one everyone uses to signe zips)
and Nexus 5 test field from the play store
and o/c ADB
EDIT: to get SPC
http://forum.xda-developers.com/showthread.php?t=2515798
*#*#3282#*#* doesn't work
so you'll need http://forum.xda-developers.com/showthread.php?t=2524744
or simply in adb type "am start -n com.lge.SprintHiddenMenu/.sprintspec.Debug"
to arrive to the "6. Select "LTE/Edit" again."
you need stock rom for that unless you resign the apk I mentionned above.