Related
Plugged in Transformer last night to charge it up overnight when the battery hit 30%. I updated the firmware yesterday morning and everything was going swimmingly.
Woke it up this morning, and found it was at 9% battery remaining and had a low battery warning. I had a closer look and the battery icon shows no indication that it's charging when it's plugged in.
Right now I've plugged it into a bog-standard USB charger and turned it off, hoping it'll trickle charge (damn the lack of a charge LED!) and that it's a fault with the power adapter rather than the device itself.
Anyone else had this issue?
I had the same problem a few days ago, my charger was plugged in via a multi block and it would not charge.
I even went to the extreme of taking my device back to comet in the hope I could swap the charger out with their demo unit.
Man behind counter plugs my charger into some sort electrical surge protected socket and it starts charging straight away leaving me looking like a right tool standing their. (and they tried to sell me 3 years extended cover)
Brought it home and plugged it into the very socket where it wasn't working and what do you know? It starts working!
Not sure what the issue was but it now works again.
Ok well that's good to know!
On trickle-charge it's now gone up by 2% since I posted.
Looks like the power adapter has its own faults...
Oh, and what do you know... plugged wall charger back in (it's been unplugged for 20mins) and now it's all happy and charging again.
Hooray.
yeah maybe that 20 minute trip to comet fixed mine too..
the USB mains adapter plug has a fatal flaw - the middle part of the usb connection isn't as sturdy as it sould be so it is easy to plug a USB port in the wrong way around and it looks and feels plugged in correctly as the middle part just moves out of the way.
If it isn't charing always check to make sure the USB connection is in the right way around in the plug.
I am bummed about this proprietary power connector; and apparently proprietary USB cable with extra pins (negating the use of USB extension cables). I wish the TF had a standard round power adapter similar to the Acer A500.
Thank God, i thought i was the only one. Had exactly this problem with mine when it arrived a couple of days ago, i am lucky enough to have lots of USB chargers around so i tried and tested various combinations and tried to charge other devices with the asus charger.
The problem lies as far as i can see, entirely with the charger unit. The charger comes in two parts, one is the usb dock and the other the relevant country plug. The way the plug fits onto the face of the charger is the important part. There is a central 'locating pin' made from plastic and two contacts that slot into the charger carrying the live and negative. The construction of this part is very, very poor. The tolerances are not a match for the quality of the plastic, the T shaped plastic locater does not actually locate the bottom pins properly and needs a great deal of force to lock in placce, and here is the best part, it doesnt like STAYING locked. As the plastic is weak, and we are looking at just a couple of mm here, it will snap, that will stop there being a clean contact and no charge. As a remedy, i have secured the face plate to the charger very tightly with a high tech rubber band
I agree, the use of specific power connectors in this day and age is just as dumb a decision as any manufacturer can make, and the rate it recharges at from a USB to PC connection can only be described as comical, a full recharge in 26 hours . Aside from all that its nigh on perfect, but i can see power related alternatives being VERY popular until Asus catches up with the rest of the electronics industry.
havent even had mine an hour and i havent done the update because its not at 50% and it will not charg at all. when i first tried to start it i thought it was doa because it would not turn on. guess ill take you guys advice and leave it unplugged for a while. i hate the charging cable is so small too that definately sucks.
Hmmm... if only a few other people created topics about not charging...
Charging port is loose and I have to push the charger in hard pull up and to the left and wrap the cord around it or hold it to get it to charge. I know there are many threads/youtube vids about this but nothing specific to the Charge.
This used to happen to my old droid x/x2 but a new charger would always fix it. I've tried about 8 different chargers and bought a new micro usb cord today with no avail. I ordered an actual nicer Samsung charger off of ebay (still waiting) but thinking at this point it won't help. It started by being loose, then having to lift it a little and has progressed over a few weeks to this point.
I'm wondering if I'm missing something and samsung chargers are slightly different in the port, if I can solder it myself, how difficult to do? I'd really like to avoid operating on it? What's going on at the pin level.
Thanks in advanced I'm pretty desperate at this point.
Having a bit of a strange issue where my Galaxy S3 will randomly vibrate/wake for no reason when plugged into a T-Mobile universal wall charger. Seems to happen when the phone is jostled or picked up; it will turn the screen on and vibrate as if I had a notification, but I don't. The charger is a little bit old, since it was purchased with a BlackBerry about 2 years ago, so perhaps that's the reason. I was just wondering if this is something to worry about, like my USB connector going bad or something. It doesn't seem to do this when plugged into other chargers (will occasionally do this when charging on the OEM Samsung dock, but rarely). Thanks in advance.
Devilicus said:
Having a bit of a strange issue where my Galaxy S3 will randomly vibrate/wake for no reason when plugged into a T-Mobile universal wall charger. Seems to happen when the phone is jostled or picked up; it will turn the screen on and vibrate as if I had a notification, but I don't. The charger is a little bit old, since it was purchased with a BlackBerry about 2 years ago, so perhaps that's the reason. I was just wondering if this is something to worry about, like my USB connector going bad or something. It doesn't seem to do this when plugged into other chargers (will occasionally do this when charging on the OEM Samsung dock, but rarely). Thanks in advance.
Click to expand...
Click to collapse
It could be the charger that you are using. I have the same issue using my old DX charger but not with the charger that came with the GS3. With the older chargers it tends to lose connection and the connect backup, as if you unplugged it and plugged it back in.
Yeah that makes sense; do you know if I might have damaged the charging port by using that old charger or is that unlikely? I haven't really noticed any other issues with charging so I'm hoping everything is fine. Made sure to stop using that charger just in case though.
Devilicus said:
Yeah that makes sense; do you know if I might have damaged the charging port by using that old charger or is that unlikely? I haven't really noticed any other issues with charging so I'm hoping everything is fine. Made sure to stop using that charger just in case though.
Click to expand...
Click to collapse
I still use the charger, it's just not idea if you are looking at something when it is plugged in. As far as it damaging the port I don't think so, unless your trying to plug it in upside down!!
I think the charger that came with the S3 just fits tighter and the older chargers may just be worn down by use. That's just my thoughs!!
mapatton82 said:
I still use the charger, it's just not idea if you are looking at something when it is plugged in. As far as it damaging the port I don't think so, unless your trying to plug it in upside down!!
I think the charger that came with the S3 just fits tighter and the older chargers may just be worn down by use. That's just my thoughs!!
Click to expand...
Click to collapse
Ok good, that's good to know. Thanks for the help, I appreciate it
The tablet needs a new charging/interface port and was wondering if anyone knows where I can get one?
I have searched Ebay and the net for a used/new one. The port looks fine but when plugging the cable in it won't charge. Sometimes I can get it to if I push and hold it just right however this is tricky to do and does not work often. So right now it is a dead brick. The pins must not be making full contact for some reason.
Ive bought parts from these guys before, I don't see a charging port but might be worth giving them an email and asking
http://www.asusparts.eu/partfinder/Asus/Pad/Eee pad/TF101
*Detection* said:
Ive bought parts from these guys before, I don't see a charging port but might be worth giving them an email and asking
http://www.asusparts.eu/partfinder/Asus/Pad/Eee pad/TF101
Click to expand...
Click to collapse
Thanks but I would rather not have to order parts from Sweden. If I have to I'll just keep watching Ebay. Every so often one pops up but doesn't last very long.
Good luck
The parts I ordered took about 4-6 weeks to arrive iirc
Just installed a new (used off Ebay) charging port with fingers crossed that it will allow the tablet to charge. I also have a new high quality charging cord (PWR+) and two ASUS wall chargers that I know work. Plugged the tablet in and was relieved to see the tablet come right on and show it charging. Let it charge to about 20% and then decided to unplug it so I could put the ring back on the tablet so it is all back together. Get the ring on and plug the tablet back in and nothing. I'm about to throw this thing in the trash right now. So fed up with these charging issues. What changed? All I did was unplug it, put the ring on, and plug back in.
So for kicks I decide to try the other wall charger and what do you know....it came on immediately and started charging and is still charging. I'm afraid to touch the thing now. Seems once it is charging and undisturbed it will charge to 100% no problem. However, when going to recharge it won't charge. Could there be something in the charging mechanism causing the thermal to trip in the wall chargers? Is there possibly a small short somewhere in the charging mechanism? Anyone have an opinion on why this is happening? Only other thing I can think of is doing a full wipe/reset and maybe flashing another rom (is currently on newest Android Revolution HD) once it is charged up.
Could the ring (I assume you mean Bezel ? ) or the screws near the port be shorting the charging port to earth/ground/chassis ?
*Detection* said:
Could the ring (I assume you mean Bezel ? ) or the screws near the port be shorting the charging port to earth/ground/chassis ?
Click to expand...
Click to collapse
Yep.. Sry.. The bezel. Not sure how but anything is possible. Would indicate to me a faulty charging port or charger cord and is happening on multiple. Tablet is still allowing me to charge it at this time after switching chargers and with the bezel on so will have to see how it goes.
Sent from my tricked out S4.
Fingers crossed it was a coincidence with the first charger, if not, I'd try taking the bezel off again and see if you can spot the short / see if it works again with the bezel off, or even just with the screws out
Ok, first a little background on this issue...
After having my S3 for about 13-14 months I started having charging issues. The charging port was very "loose" and I had to make sure my charger cable was in just right to get my phone to charge. This was annoying, however was out of warranty and didn't want to pay vzw for an insurance claim. This got worse, and eventually I noticed my phone would only charge with 1 specific usb cable, 1 specific wall charger, and 1 specific car charger.
Well, I finally called Samsung and explained the situation to them and they had me chip my phone to them and they would repair it, free of charge. When they had it, they replaced the charging port, the headphone jack, and the screen. I received the phone back after couple weeks, super excited, and immediately charged it up with the cable I had next to my bed. New charging port felt perfect, nice snug fit, etc... Well, after a few days i hooked it up with the original usb cable that came with the phone, nothing happened. So i started messing around and realized that the only usb cables that will charge my phone are Motorola brand cables! At least the 2 cables I have work, and not a single other cable I've tried works! This includes stock Samsung cable, many cheap 3rd party cables, other friend's S3 cables, none work. Also, I have this cheap car charger that is the type you plug a USB cable into that works, however any other car charger I've tried does not work either.
Also, when i say the cables won't charge my phone, it also won't connect the phone to a PC. They do absolutely nothing.
Does anyone have ANY idea why this is happening?!?! It was an issue before Samsung repaired my phone, they replaced the charging port, but I still have this issue!! I can send it back to Samsung for them to look at it again, however my backup phone, a Razr Maxx, just died also. Seems like the battery went dead and now I can't get it to charge, but that's another issue.
So, any ideas?!
JHibinger said:
Ok, first a little background on this issue...
After having my S3 for about 13-14 months I started having charging issues. The charging port was very "loose" and I had to make sure my charger cable was in just right to get my phone to charge. This was annoying, however was out of warranty and didn't want to pay vzw for an insurance claim. This got worse, and eventually I noticed my phone would only charge with 1 specific usb cable, 1 specific wall charger, and 1 specific car charger.
Well, I finally called Samsung and explained the situation to them and they had me chip my phone to them and they would repair it, free of charge. When they had it, they replaced the charging port, the headphone jack, and the screen. I received the phone back after couple weeks, super excited, and immediately charged it up with the cable I had next to my bed. New charging port felt perfect, nice snug fit, etc... Well, after a few days i hooked it up with the original usb cable that came with the phone, nothing happened. So i started messing around and realized that the only usb cables that will charge my phone are Motorola brand cables! At least the 2 cables I have work, and not a single other cable I've tried works! This includes stock Samsung cable, many cheap 3rd party cables, other friend's S3 cables, none work. Also, I have this cheap car charger that is the type you plug a USB cable into that works, however any other car charger I've tried does not work either.
Also, when i say the cables won't charge my phone, it also won't connect the phone to a PC. They do absolutely nothing.
Does anyone have ANY idea why this is happening?!?! It was an issue before Samsung repaired my phone, they replaced the charging port, but I still have this issue!! I can send it back to Samsung for them to look at it again, however my backup phone, a Razr Maxx, just died also. Seems like the battery went dead and now I can't get it to charge, but that's another issue.
So, any ideas?!
Click to expand...
Click to collapse
What rom/kernal
It doesn't matter. It does this when it is totally stock and rooted. Right now I'm not rooted or anything because it looks like it may be going back to Samsung again.
JHibinger said:
It doesn't matter. It does this when it is totally stock and rooted. Right now I'm not rooted or anything because it looks like it may be going back to Samsung again.
Click to expand...
Click to collapse
I think the smart charging circuit may be messed up
Really? How would that cause the phone to not work with any cable except a certain brand?? I'm just really curious and this is driving me insane!!
JHibinger said:
Really? How would that cause the phone to not work with any cable except a certain brand?? I'm just really curious and this is driving me insane!!
Click to expand...
Click to collapse
I would say you are putting mechanical stress on the charging port. This could be from some misaligned or mis-made cable or somehow pressing or pulling the charge cable when its connected. I've never seen this reported by anyone else, but the mechanical connections are not indestructible. If it were a common symptom with 100 million S3s having been sold, there would be a firestorm of complaints.
I have a similar issue. I'm not sure if it's the device or the ROM (CM nightlies).
Certain cables force the screen to turn back on, which means I get negative charge because the screen burns more than the charger is capable of supplying. Other cables are fine. I'm still looking for the pattern, it's super annoying and causes me to have to turn my phone off completely at times so as not to lose my battery altogether. I'm still trying to solve this, any help would be appreciated.
rgrossie said:
I have a similar issue. I'm not sure if it's the device or the ROM (CM nightlies).
Certain cables force the screen to turn back on, which means I get negative charge because the screen burns more than the charger is capable of supplying. Other cables are fine. I'm still looking for the pattern, it's super annoying and causes me to have to turn my phone off completely at times so as not to lose my battery altogether. I'm still trying to solve this, any help would be appreciated.
Click to expand...
Click to collapse
Further info- it's not the cable, it's the converter at the end. I think it has to do with amperage of the charger- if I use the stock samsung one I'm good, it's putting out 1.0A. If I use others that are fewer amps (like 700 mA) it's unpredictable. I suspect a kernel thing, I might download different kernels to play with it.
rgrossie said:
Further info- it's not the cable, it's the converter at the end. I think it has to do with amperage of the charger- if I use the stock samsung one I'm good, it's putting out 1.0A. If I use others that are fewer amps (like 700 mA) it's unpredictable. I suspect a kernel thing, I might download different kernels to play with it.
Click to expand...
Click to collapse
Always use chargers that is 1 A - 2A the circuit controls most of the charging regulating amps and voltage
Yes, I agree about using good chargers, but my phone wasn't always this way. It used to charge with anything, but no longer.
I enabled fast charge on Imosyen's lean kernel. That might have made a difference, but I'm not positive yet.