Hi to All,
I want to share my experience about revert to stock for users that have new HBOOT, unlocked bootloader and custom recovery; can't execute official RUU. ( This method i think is more safe that downgrade HBOOT )
Step ONE:
Install this custom ROM: MaximuS ROM ( read the thread for instruction about installation of this ROM )
( this ROM allow you to receive the message of OTA JB update, if you know another ROM that receive this message you can use as well i think )
Step TWO:
install the stock recovery of HTC One S via fastboot ( after flashing recovery erase cache )
Step THREE:
Reboot your phone in system, configure the rom for first use, go to settings, information, software update and press check now for update.
You'll receive the message for an update, download and install, and now you have stock JB ROM. after reboot you can do a reset ( go to setting => backup and restore ) to clean the application migrated from previous ROM ( MaximuS )
I hope this can help someone else.
p.s. Sorry for my English!
Thanks bro for this, but my problem is not resolved because this rom couldn't install on my HTC One S, i dont know why... Log show me: MD5 files not found
CybulPL said:
Thanks bro for this, but my problem is not resolved because this rom couldn't install on my HTC One S, i dont know why... Log show me: MD5 files not found
Click to expand...
Click to collapse
Witch recovery are you using at the moment? I installed this ROM ( MaximuS ) with Team Win Recovery ( TWRP ) v2.3.3.0 and it's works for me.
( after flashing ROM from recovery remember to flash boot.img by fastboot )
Maverick87Shaka said:
Witch recovery are you using at the moment? I installed this ROM ( MaximuS ) with Team Win Recovery ( TWRP ) v2.3.3.0 and it's works for me.
( after flashing ROM from recovery remember to flash boot.img by fastboot )
Click to expand...
Click to collapse
I use TWRP and CWM and the same. My mate told me that i have unmount 1 and 2 partition in recovery but i don't know how.
Hi everyone,
thanks a lot, this saved my ass ... I had upgraded my stock ICS to stock JB and then tried to go back to stock ICS with a CWM backup - with the result that I had a brick booting only to a black screen.
I still had access to CWM recovery and so could install the Maximus 2.5 ROM and also the update to stock JB ran through just fine.
I did a factory reset afterwards, is it 100% sure that I now have a pure stock JB or could there be some leftovers from the Maximus 2.5 ROM?
Cheers,
Tim
tim_h said:
Hi everyone,
I still had access to CWM recovery and so could install the Maximus 2.5 ROM and also the update to stock JB ran through just fine.
I did a factory reset afterwards, is it 100% sure that I now have a pure stock JB or could there be some leftovers from the Maximus 2.5 ROM?
Cheers,
Tim
Click to expand...
Click to collapse
Yes you have a stock JB, because with factory reset you've removed all extra application that there is inside MaximuS v.2.5.
All other unneeded file or executable ( like root executable and all other script in /system ect. ) was removed during installation of new ROM.
Remember just that you need to revert to stock to give your phone back to HTC for guarantee, I thinks you must leave on it the stock recovery.
tim_h said:
Hi everyone,
thanks a lot, this saved my ass ... I had upgraded my stock ICS to stock JB and then tried to go back to stock ICS with a CWM backup - with the result that I had a brick booting only to a black screen.
Cheers,
Tim
Click to expand...
Click to collapse
It's happened because from recovery the system was unable to flash the boot partition. So after you did the CWM restore, you have all the phone with ICS android, but JB kernel, this cause your black screen after boot!!!
If you have the boot.img ( with suitable kernel of your old ROM ) to flash after you did the CWM recovery, you can get back to your BACKUP without any problem.
Also if you don't have the exactly boot.img of your previous ROM of the backup, you can flash any boot.img by fastboot of ICS kernel and this is should be enough to keep your backup running again.
Thanks very much for the additional explanations. I do have the boot.img of my original CWM backup, so should be able to restore it via fastboot. Great!
But first I have to send in my phone to have the USB port fixed under warranty.
Holy ****, is working, thanks man...
zujko said:
Wait to see if i understood, i have now Custom ( Virtuous Ville+ RC-1) JB ROM, with hboot 2.15.0000... unlocked, root, twrp
1.install maximuS V2.5, wipe..
2. flash boot.img with fastboot
3.Check update for JB, and flash new update JB?
And that's it?
I guess we have to make relock bootloader, after flash ICS?
Tnx
Click to expand...
Click to collapse
You just forgot in the list to install the HTC Stock recovery before check the message of update, so:
1 => Wipe and install MaximuS V2.5 ROM
2 => flash with fastboot boot.img of MaximuS V2.5 ROM
3 => flash stock HTC Recovery via fastboot ( fastboot flash recovery ville_recovery_signed.img , then fastboot erase cache ) or get it from One_S_All-In-One_Kit_v1.0
4 => start the phone and check for the JB update
5 => after JB installation do a factory reset to clean up the ROM from the extra application that MaximuS ROM have.
You don't need to relock your bootloader, you just need to install the stock recovery, that's enough.
Hmm, wait, why need install stock recovery?
This JB will be working with custom twrp?
EDIT: I got it
I did it! I unmounted first 3 partitions in TWRP and installation successful.
I am on stock Rom now and used HTC offical update to get to jb...do u think I will have trouble rooting again?
Sent from my HTC One S using xda premium
k1llacanon said:
I am on stock Rom now and used HTC offical update to get to jb...do u think I will have trouble rooting again?
Sent from my HTC One S using xda premium
Click to expand...
Click to collapse
I will let you know if I can get it working and flashed it will be rooted in seconds just need stock recovery.
Rooted without a problem, recommend the attached superuser app.
Maverick87Shaka said:
You just forgot in the list to install the HTC Stock recovery before check the message of update, so:
1 => Wipe and install MaximuS V2.5 ROM
2 => flash with fastboot boot.img of MaximuS V2.5 ROM
3 => flash stock HTC Recovery via fastboot ( fastboot flash recovery ville_recovery_signed.img , then fastboot erase cache ) or get it from One_S_All-In-One_Kit_v1.0
4 => start the phone and check for the JB update
5 => after JB installation do a factory reset to clean up the ROM from the extra application that MaximuS ROM have.
You don't need to relock your bootloader, you just need to install the stock recovery, that's enough.
Click to expand...
Click to collapse
Will this work on a T-Mobile HOS with CID HTC__001?
I have followed all the steps from above
- installed the rom
- installed the stock recovery
- then I was able to start the update but when it finished downloading .. I was told that the HTC software on my device has been modified and please revert back and try the update again and it would not preform the update.
What am I doing wrong?
Thanks in Advance
Hi once more,
after going back to pure stock JB this way, can I relock the bootloader to get "RELOCKED" instead of "UNLOCKED/TAMPERED"? (That would be good for sending in my phone under warranty.) Or will the phone stop booting if I relock the bootloader?
As far as I understood, the "canonical" way to get "RELOCKED" would be to lock the bootloader and install the RUU, but since there is no RUU for the unbranded JB yet and downgrading with an older RUU is not possible, I cannot do this.
Cheers,
Tim
tim_h said:
Hi once more,
after going back to pure stock JB this way, can I relock the bootloader to get "RELOCKED" instead of "UNLOCKED/TAMPERED"? (That would be good for sending in my phone under warranty.) Or will the phone stop booting if I relock the bootloader?
Cheers,
Tim
Click to expand...
Click to collapse
You can do Relock bootloader, i think it will boot to system without problem(?)
blah blah blah said:
Will this work on a T-Mobile HOS with CID HTC__001?
I have followed all the steps from above
- installed the rom
- installed the stock recovery
- then I was able to start the update but when it finished downloading .. I was told that the HTC software on my device has been modified and please revert back and try the update again and it would not preform the update.
What am I doing wrong?
Thanks in Advance
Click to expand...
Click to collapse
+ 1
Sent from my HTC One S using xda app-developers app
The only word of caution that I think needs to be shared on almost all threads related to JB updates is to make sure you DO NOT have SuperCID... There have been numerous reports of phones bricking with the OTA JB update with a SuperCID... So if you had previously SuperCID your phone with 11111111, definately change it to something else.
AKToronto said:
The only word of caution that I think needs to be shared on almost all threads related to JB updates is to make sure you DO NOT have SuperCID... There have been numerous reports of phones bricking with the OTA JB update with a SuperCID... So if you had previously SuperCID your phone with 11111111, definately change it to something else.
Click to expand...
Click to collapse
I had to go supercid to run the euro ruu and changed it to HTC__001. Ota still didn't work
Sent from my HTC One S using xda app-developers app
Related
I've a huge problem
I've a Sensation 4g I was on stock ics and i followed the guide to get root, htc dev unlock e CWM... (still s.off) after that I installed 4ext and ARHD 6.7.0.. and everything was fine..
Then i tried to install cyanogenmod 9 which requires CWM again.. so i've installed rom manager and installed cwm through it..
I was stuck on the bootloader image, so i tried to flash back my recovery which of course isn't working because i have CWM now and so i tried to flash back ARHD but it will get untill the beginning when it says "optimizing app" and it restarts and again and again....
Anyway i can fix this problem?? I tried to flash another rom "energy ics" which don't require 4ext.. but i got the same results!!! what should i do?! did i brick my phone?
anyway to install 4ext without having a rom working?
andre_07 said:
I've a huge problem
I've a Sensation 4g I was on stock ics and i followed the guide to get root, htc dev unlock e CWM... (still s.off) after that I installed 4ext and ARHD 6.7.0.. and everything was fine..
Then i tried to install cyanogenmod 9 which requires CWM again.. so i've installed rom manager and installed cwm through it..
I was stuck on the bootloader image, so i tried to flash back my recovery which of course isn't working because i have CWM now and so i tried to flash back ARHD but it will get untill the beginning when it says "optimizing app" and it restarts and again and again....
Anyway i can fix this problem?? I tried to flash another rom "energy ics" which don't require 4ext.. but i got the same results!!! what should i do?! did i brick my phone?
anyway to install 4ext without having a rom working?
Click to expand...
Click to collapse
yes flash recovery using this guide
FLASHING ROMS WITH SON
just follow step 2 from above guide if you are SOFF
if SON follow step 2 and 3
Did you install the correct firmware? ICS based Roms is usually 3.32, firmware ?
Sent from my HTC Sensation 4G using xda premium
realsis said:
Did you install the correct firmware? ICS based Roms is usually 3.32, firmware ?
Sent from my HTC Sensation 4G using xda premium
Click to expand...
Click to collapse
Let's say right now I've a big confusion in my head.. Beore I had ICS working.. i never even tried to downgrade so i should have the correct firmware right?
the last time i check i had 1.32 (and don't remember but it was the last one installed with the tmous OTA)...
Maybe when i did my first format of the sd should i've installed something before the rom?
can anyone giving me the exact path of the cwm backup?
andre_07 said:
can anyone giving me the exact path of the cwm backup?
Click to expand...
Click to collapse
andre read my previous post to flash 4EXT this doesn't require a working rom
also in normal the backups are present on SDCRAD
ie /sdcard/clockworkmod/backup
so once you format the sdcard you will lose the backups
andre_07 said:
Let's say right now I've a big confusion in my head.. Beore I had ICS working.. i never even tried to downgrade so i should have the correct firmware right?
the last time i check i had 1.32 (and don't remember but it was the last one installed with the tmous OTA)...
Maybe when i did my first format of the sd should i've installed something before the rom?
Click to expand...
Click to collapse
If I read this correct you have the official stock firmware that was with the T-Mobile OTA ICS update. This means your bootloader is locked even though you are S-off. You need to flash a engineered Hboot to solve this. Go to this thread to get a firmware package with this. Go to the "User-Friendly Firmware" thread by Kohr-Ah, or you can also use the firmware from GROG88's thread here.
Hey Guys,
yesterday I wanted to revert my ROM from CM10 to TrickDroid 7.1. In TWRP 2.2.1 I wiped caches and did a factory reset and then flashed TD 7.1 following torxx's instructions (wipe, install ROM, flash boot.img with his boot flash script, let the ROM boot). After the reboot the phone hang. The startup sound came through but then no further action for about 7 Minutes.
Was that too little time waiting? Or is there any other issue interfering the boot process after reverting from Android 4.1.1 to 4.0.4 Sense?
If anyone can help is much appreciated. Even if I look stupid afterwords
Burkhard
herzbert said:
Hey Guys,
yesterday I wanted to revert my ROM from CM10 to TrickDroid 7.1. In TWRP 2.2.1 I wiped caches and did a factory reset and then flashed TD 7.1 following torxx's instructions (wipe, install ROM, flash boot.img with his boot flash script, let the ROM boot). After the reboot the phone hang. The startup sound came through but then no further action for about 7 Minutes.
Was that too little time waiting? Or is there any other issue interfering the boot process after reverting from Android 4.1.1 to 4.0.4 Sense?
If anyone can help is much appreciated. Even if I look stupid afterwords
Burkhard
Click to expand...
Click to collapse
Perhaps your hboot does not allow flashing or boot.img? Have you tried the fastboot method of flashing boot.img? How about reverting to a nandroid of a sense based ROM, then flashing TD?
el_smurfo said:
Perhaps your hboot does not allow flashing or boot.img? Have you tried the fastboot method of flashing boot.img? How about reverting to a nandroid of a sense based ROM, then flashing TD?
Click to expand...
Click to collapse
Prior to CM10 I was on latest stock ROM. Before that I had custom ROMs. HBoot on my phone after the OTA update is 1.14. Flashing the boot image of CM10 was no problem.
In order to use the phone I reinstalled CM10 and it works.
The boot images were flashed within fastboot. I do not know any other way to flash a boot image.
I dont have a nandroid backup.
Checked MD5?
torxx said:
Checked MD5?
Click to expand...
Click to collapse
They correspond.
If nothing else helps I will try to install the latest RUU and then flash a ROM. But I wanna circumvent the relock and unlock procedure.
Btw: Did anybody notice that the unlock code changes after an update of HBoot? Nobody mentioned that when the new base was released.
Same here... But fine now
herzbert said:
They correspond.
If nothing else helps I will try to install the latest RUU and then flash a ROM. But I wanna circumvent the relock and unlock procedure.
Btw: Did anybody notice that the unlock code changes after an update of HBoot? Nobody mentioned that when the new base was released.
Click to expand...
Click to collapse
Hey there,
I was having the same problems as you messioned. I flashed the boot.img through fastboot myself and some how it then worked Did not have an problems with flashing the boot.img before. But maybe its worth a try.
Of course you need to use fastboot!!
Did not try yet to flash the RUU. There was an update of CM10 yesterday. The heavy battery drain is gone with this update and there is no urgent need to go back to TrickDroid right now.
herzbert said:
Prior to CM10 I was on latest stock ROM. Before that I had custom ROMs. HBoot on my phone after the OTA update is 1.14. Flashing the boot image of CM10 was no problem.
In order to use the phone I reinstalled CM10 and it works.
The boot images were flashed within fastboot. I do not know any other way to flash a boot image.
I dont have a nandroid backup.
Click to expand...
Click to collapse
HBoot 1.14 is the problem. Anything above 1.09 needs special steps to flash unlike simply flashing with twrp as with 1.09 and below.
Sent from my HTC VLE_U using Xparent SkyBlue Tapatalk 2
LikeaG2root said:
HBoot 1.14 is the problem. Anything above 1.09 needs special steps to flash unlike simply flashing with twrp as with 1.09 and below.
Alright, so, what are these special steps? Can you tell? If its not flashing the within recovery and push the boot.img via fastboot to the phone I would be very interested. My previous HBoot version was 1.13. Flashing ROMs was never a big deal. Also not going to CM9 and back to sense based ROMs.
Click to expand...
Click to collapse
I am on hboot 1.14 and it worked via fastboot. Like you mentioned yourself you reinstalled CM10 and it booted, therefore your previous flash of the boot.img didn't work. So just flash the boot.img via bootloader and fastboot and you should be good...
HighRoIIer said:
I am on hboot 1.14 and it worked via fastboot. Like you mentioned yourself you reinstalled CM10 and it booted, therefore your previous flash of the boot.img didn't work. So just flash the boot.img via bootloader and fastboot and you should be good...
Click to expand...
Click to collapse
I did also flash the boot.img via fastboot. Why do you say that anyway? Is there another method to flash a boot.img?
you didn't mention wiping System as part of the full wipe--needs done
Partially solved
rugmankc said:
you didn't mention wiping System as part of the full wipe--needs done
Click to expand...
Click to collapse
Right, I did not mention it because system is wiped by TWRP during flashing the ROM. So there was no need to wipe it seperately. But maybe my mistake was not to wipe data and the new "asec" folder messed things up.
I'll never know because yesterday I did a complete wipe including the SDCard. Afterwards I was able to install TrickDroid flawlessly.
Thank you all for your efforts.
To the Guru of this forum. After my last rom flashing my device is keeping booting into recovery :crying:. Is it briked ? If so my only hope is the unbricking project ? Thanks in advance.
What recovery are you running?
Can you use the power menu within recovery to boot into bootloader?
Also, please provide as much pertinent info as possible, ie: rom you flashed, firmware, s-off or s-on, locked or unlocked. With your description it's basically like saying, "my car makes a noise all the time. what is causing it?".
Its not bricked.If u can enter recovery
Sent from my HTC sensation
Sorry you are right:
What recovery are you running? 4Ext
Can you use the power menu within recovery to boot into bootloader? yes
The device is HTC unlocked with S-On.
Rom JBMIUI v4.1 2.8.31 R2.
HBOOT 1.27.0000
firmware 3.33.401.6
I've format everything but SD. Restored the most recent back up done today before flashing. Once it reboots HTC logo comes up once, black screen, HTC logo, 4Ext is coming up saying that smartflash it is set to update the boot partition on next system start asking if this should be removed.
I've downloaded and installed again PG58IMG *different files using bootloader
I've founded a 3.33.401.6-Unsecured-Boot.img,+Root+Busybox zip file that can be installed via recovery but it did not help.
At this point I need a bit of help to look into the right direction and I'm not sure that Unbrick_Pyramid is the right way.
Thanks again.
Try turning off smartflash and flash a 3.33 stock rom to see if it will boot.
What was your last working setup, and what were you trying to install?
Sent from my HTC Sensation 4G using Tapatalk 2
Hi. Manage to flash a stock 3.33.
It stopped to reboot straight into recovery.
Sits now on HTC logo now for about 10 mins. I plan to let him run for 1 hr and see what happens.
Was thinking to install CWM on the basis that could be a 4ext recovery issue, toughs?
GROGG88 said:
Try turning off smartflash and flash a 3.33 stock rom to see if it will boot.
What was your last working setup, and what were you trying to install?
Sent from my HTC Sensation 4G using Tapatalk 2
Click to expand...
Click to collapse
If you can install clockworkmod that may help.
Tge device isnt getting the message that it has already booted into recovery once. So something may be jacked up with 4ext.
Clockwork may bypass all that when it doesnt know what to do with that signal to run smartflash.
Worst case scenario...put a full pm58img containing a rom and recovery on the sf card and flash that through bootloader.
You should still be able to get to bootloader as the device looks for that option first.
Sent from my HTC Sensation using xda app-developers app
Hallo. Ok installed CWM. Can please direct me to a full pm58img as you mentioned ? Thx.
Skipjacks said:
If you can install clockworkmod that may help.
Tge device isnt getting the message that it has already booted into recovery once. So something may be jacked up with 4ext.
Clockwork may bypass all that when it doesnt know what to do with that signal to run smartflash.
Worst case scenario...put a full pm58img containing a rom and recovery on the sf card and flash that through bootloader.
You should still be able to get to bootloader as the device looks for that option first.
Sent from my HTC Sensation using xda app-developers app
Click to expand...
Click to collapse
DiscreteTask said:
Hallo. Ok installed CWM. Can please direct me to a full pm58img as you mentioned ? Thx.
Click to expand...
Click to collapse
And did that help? Are you able to get into recovery without errors now? If so you should be able to flash a fresh version of any ROM.
Try that first. Get any ROM. Flash it. See if it boots.
If you have successfully replaced 4EXT I will bet a fresh flash of a ROM will now boot.
Also worth a shot is replacing or upgrading the firmware, as that could be what's sending the phone into recovery on each boot (though this is less likely that 4EXT just being broken)
Flash a firmware PM58IMG like 3.32 or 3.33 and see if that helps.
But for starters, put a fresh ROM on the SD card and flash it with CWM. (BE SURE IT'S A ROM THAT DOESN'T REQUIRE 4EXT!!)
Once you've got it all fixed you can switch back to 4EXT. I have a feeling it was just the copy you were running that got botched. The software itself is solid and stable. A new copy shoudl work fine now.
CWM v5.0.2.0 was installed fine.
3.33 firmware installed once again.
Using this I've installed ROM that I already did in the past w/o luck, they all sit on the HTC logo. Is like the initial boot sequence is broken. Is boot.img part of the firmware or ROM ?
Trying to download some additional ones.
Thanks,
Skipjacks said:
And did that help? Are you able to get into recovery without errors now? If so you should be able to flash a fresh
version of any ROM.
Try that first. Get any ROM. Flash it. See if it boots.
If you have successfully replaced 4EXT I will bet a fresh flash of a ROM will now boot.
Also worth a shot is replacing or upgrading the firmware, as that could be what's sending the phone into recovery on each boot (though this is less likely that 4EXT just being broken)
Flash a firmware PM58IMG like 3.32 or 3.33 and see if that helps.
But for starters, put a fresh ROM on the SD card and flash it with CWM. (BE SURE IT'S A ROM THAT DOESN'T REQUIRE 4EXT!!)
Once you've got it all fixed you can switch back to 4EXT. I have a feeling it was just the copy you were running that got botched. The software itself is solid and stable. A new copy shoudl work fine now.
Click to expand...
Click to collapse
DiscreteTask said:
CWM v5.0.2.0 was installed fine.
3.33 firmware installed once again.
Using this I've installed ROM that I already did in the past w/o luck, they all sit on the HTC logo. Is like the initial boot sequence is broken. Is boot.img part of the firmware or ROM ?
Trying to download some additional ones.
Thanks,
Click to expand...
Click to collapse
The more details you give, the better the answers will be. Don't consider any detail too small.
What do you mean you installed ROM's that you had done in the past? Do you mean you are trying to restore a backup made with 4EXT?
That won't work. You need to flash a fresh version of the ROM after wiping.
Also, CWM won't install some ROM's that you may have used in the past. What ROM are you trying to install?
The HTC logo that first pops up when you hit the power button is part of the firmware.
Make sure you do a full wipe of everything but the SD card from within CWM. Get whatever's causing the problem off that way. Then flash a fresh install of a ROM from scratch.
Hi.
I did not use any backup only fresh ROMs: ARHD, Elegantia, but also stock ROMs I could find.
I've tried also some PG58IMG with ROM included.
Cheers.
Skipjacks said:
The more details you give, the better the answers will be. Don't consider any detail too small.
What do you mean you installed ROM's that you had done in the past? Do you mean you are trying to restore a backup made with 4EXT?
That won't work. You need to flash a fresh version of the ROM after wiping.
Also, CWM won't install some ROM's that you may have used in the past. What ROM are you trying to install?
The HTC logo that first pops up when you hit the power button is part of the firmware.
Make sure you do a full wipe of everything but the SD card from within CWM. Get whatever's causing the problem off that way. Then flash a fresh install of a ROM from scratch.
Click to expand...
Click to collapse
Arhd and elegencia wont work with cwm. So there is your isdue. Try cm9 or 10 to see if you can boot one of those.
Sent from my HTC Sensation using xda app-developers app
Hallo, after trying all option the following did work for me:
- re-lock bootloader via fastboot oem lock
- apply stock ROM founded in this list http://forum.xda-developers.com/showthread.php?t=1074559
- rebooted fine
I guess that HTC RUU had some superpower and erase and installed whatever file(s) were corrupted.
Now I'm on stock 3.6 - fw 3.33.401.106 - radio 11.76A.3504.00UU_11.24A.3504.31_M
HBOOT 1.29 - S-ON - Relocked.
Standard Recovery.
Now I'm reading how to return my device to S-OFF w/o damaging it again.
Many thanks to skipjacks & groog88 :good:
Skipjacks said:
Arhd and elegencia wont work with cwm. So there is your isdue. Try cm9 or 10 to see if you can boot one of those.
Sent from my HTC Sensation using xda app-developers app
Click to expand...
Click to collapse
Hey guys I just wanna to check and make sure I'm doing everything right before I flash cause I don't need anymore paperweights
1.I have successfully unlocked my bootloader and installed twrp recovery and rooted.
2. Now I want to back up my entire setup: rom, apps, setting, data, everything so that if I ever want to return to stock then I can. I have booted into twrp and ran backup and selected all options. Is that how you perform a nandroid backup in twrp or is there more to it?
3. I want to install team venom viper xl rom. Do I have to first flash boot.img first or is the kernel the same in stock and viper xl so that isn't necessary? Do I have to do I factory reset first or what?
I'm still new to this stuff so please bear with me. Thank for all your help!!
ImagioX1 said:
Hey guys I just wanna to check and make sure I'm doing everything right before I flash cause I don't need anymore paperweights
1.I have successfully unlocked my bootloader and installed twrp recovery and rooted.
2. Now I want to back up my entire setup: rom, apps, setting, data, everything so that if I ever want to return to stock then I can. I have booted into twrp and ran backup and selected all options. Is that how you perform a nandroid backup in twrp or is there more to it?
3. I want to install team venom viper xl rom. Do I have to first flash boot.img first or is the kernel the same in stock and viper xl so that isn't necessary? Do I have to do I factory reset first or what?
I'm still new to this stuff so please bear with me. Thank for all your help!!
Click to expand...
Click to collapse
Wipe flash Rom flash boot IMG sit back enjoy
ImagioX1 said:
Hey guys I just wanna to check and make sure I'm doing everything right before I flash cause I don't need anymore paperweights
1.I have successfully unlocked my bootloader and installed twrp recovery and rooted.
2. Now I want to back up my entire setup: rom, apps, setting, data, everything so that if I ever want to return to stock then I can. I have booted into twrp and ran backup and selected all options. Is that how you perform a nandroid backup in twrp or is there more to it?
3. I want to install team venom viper xl rom. Do I have to first flash boot.img first or is the kernel the same in stock and viper xl so that isn't necessary? Do I have to do I factory reset first or what?
I'm still new to this stuff so please bear with me. Thank for all your help!!
Click to expand...
Click to collapse
Different kernel. it is using the 2.41 RUU. So go ahead and flash the boot.img
Here's what you should do for any new ROM with a different kernel.
Wipe System
Factory Reset
Flash boot.img
Flash the ROM
flash gapps (if AOSP based)
reboot and have fun
When doing a nandroid backup, it is only necessary to backup
System
Data
Boot
Ok thanks for your response but I'm still a little confused. First did I back up my current rom properly so that I can return to it later on? Secondly does viper and boot img have to be flashed or can they be installed from sdcard via twrp? If they have to be flashed whats the fastboot command.?
ImagioX1 said:
Ok thanks for your response but I'm still a little confused. First did I back up my current rom properly so that I can return to it later on? Secondly does viper and boot img have to be flashed or can they be installed from sdcard via twrp? If they have to be flashed whats the fastboot command.?
Click to expand...
Click to collapse
You backed up fine, it just takes up a little more space.
You have to extract the boot.img from the ROM and put it in the same folder as fastboot.exe
open command prompt, and navigate to the folder fasboot.exe is in and do the following command
fasboot flash boot boot.img
If it gets stuck at waiting for device, reboot into your bootloader, boot into fastboot from there. and then try again.
ImagioX1 said:
Ok thanks for your response but I'm still a little confused. First did I back up my current rom properly so that I can return to it later on? Secondly does viper and boot img have to be flashed or can they be installed from sdcard via twrp? If they have to be flashed whats the fastboot command.?
Click to expand...
Click to collapse
Viper is the Rom u flash it from twrp it's. azip file that's fkashable so make it easy and flash viper there and than flash the boot IMG from fastboot the command is all over the forums I thinks it fastnoot flash boot.img
don't be confused. read.
you always have to flash boot.img in fastboot "fastboot flash boot boot.img" then flash the zip in twrp make sure to wipe, and don't download international roms. you still have to flash the boot.img from your backed up rom.
like a hundred threads asking the same stuff because no one wants to read
DvineLord said:
don't be confused. read.
you always have to flash boot.img in fastboot "fastboot flash boot boot.img" then flash the zip in twrp make sure to wipe, and don't download international roms. you still have to flash the boot.img from your backed up rom.
like a hundred threads asking the same stuff because no one wants to read
Click to expand...
Click to collapse
I'm sorry but I did read. I saw that if you have the same kernel as that of the rom you're flashing you don't have to flash boot.img. So I asked to see if stock and viper have the same kernel. I don't want to flash anything that will brick my phone.
Now one more question if you don't mind answering. I also saw that you can't downgrade RUU. So if viper is based on 2.41 RUU and stock is 2.20 RUU then will I be able to go stock after flashing viper?
I really do appreciate yalls help. i would be where I am if it weren't for you.
ImagioX1 said:
I'm sorry but I did read. I saw that if you have the same kernel as that of the rom you're flashing you don't have to flash boot.img. So I asked to see if stock and viper have the same kernel. I don't want to flash anything that will brick my phone.
Now one more question if you don't mind answering. I also saw that you can't downgrade RUU. So if viper is based on 2.41 RUU and stock is 2.20 RUU then will I be able to go stock after flashing viper?
I really do appreciate yalls help. i would be where I am if it weren't for you.
Click to expand...
Click to collapse
Yes. Just wipe you system and do a factory reset , and flash the boot.IMG for 2.20 and then flash the Rom.
If you want true stock 2.20 then you will have to relock your bootloader and then run the 2.20 RUU. You would only want to do this if making a warranty claim or something. If you want stock rooted, then yes, do what I said above
Sent from my HTC One XL using xda app-developers app
absolutelygrim said:
Yes. Just wipe you system and do a factory reset , and flash the boot.IMG for 2.20 and then flash the Rom
Sent from my HTC One XL using xda app-developers app
Click to expand...
Click to collapse
Ok got it. I do appreciate your help. Flashing now.
downgrading only refers to the ruu not the zipped roms. so you can't run 1.85 ruu after running 2.20 ruu/ota but you can still flash a rom based on 1.85.
if you are reflashing the same rom you don't have to reflash boot.img but if you are flashing a new rom then you need to flash boot.img. 7-zip will tell you the crc32 of files so you see tell if it's a different checksum.
Viper Xl's great. Seems to be slightly slower than stock on some task, but the lack of bloatware, and the extensive customization is worth it. Haven't found any bugs or nothing so far. If anyones familiar with viperxl though what is the last app in the app drawer? Its got a chinese name? When it loads it says Dolby Surround but all the writing is in chinese?
ImagioX1 said:
Viper Xl's great. Seems to be slightly slower than stock on some task, but the lack of bloatware, and the extensive customization is worth it. Haven't found any bugs or nothing so far. If anyones familiar with viperxl though what is the last app in the app drawer? Its got a chinese name? When it loads it says Dolby Surround but all the writing is in chinese?
Click to expand...
Click to collapse
That's because you flashed the Voodoo mod, it's apart of the mod, theres a chinese part and a english one called "Dolby Digital" or "Dolby Surround"
When I flash ViperXL 3.1.0 JB do I need to flash a radio too? My phone has hboot 1.4 and software 2.2, so I understand that I cant flash radio with hboot 1.4? Does this mean I need to downgrade my hboot/software version?
CrossFire78 said:
When I flash ViperXL 3.1.0 JB do I need to flash a radio too? My phone has hboot 1.4 and software 2.2, so I understand that I cant flash radio with hboot 1.4? Does this mean I need to downgrade my hboot/software version?
Click to expand...
Click to collapse
Most people have good luck w/out flashing another radio.
ronnie498 said:
Most people have good luck w/out flashing another radio.
Click to expand...
Click to collapse
Hmm. Might there be a patch I'm missing out on? I just flashed one file -ViperXL 3.1.0 JB - Android File Host (692MB)
edit- Works now after another reinstall installed boot image first this time.
Hi guys
I want to revert my one s to stock rom through RUU_Ville_U_JB_45_S_HTC_Europe_3.16.401.8_Radio_1.11.50.05.28_10.27.50.08L_release_301814_signed_2_4.
befor doing this I had supercid and s-off
After launching ruu ,the process stopped by error 159.
I tried other RUU_Ville_U_ICS_40_S_HTC_Europe_2.31.401.5_Radio_1 .06es.50.02.31_10.09a.50.04L_release_275655_signed
this flashed fine and worked good.
but i wanted JB so i downloaded OTA_Ville_U_JB_45_S_HTC_Europe_3.16.401.8_1.11.50.05.28_10.27.50.08L_release_301852xf01hejl416oev96
and flashed it by CWM
but in the cwm enviroment , process stopped saying cid check failed....(and a couple of cid es)
So I changed my CID to stock (HTC_203) and I went through all above steps againe but same errors......
I don't know where the problem is??
salar_bigharar2009 said:
Hi guys
I want to revert my one s to stock rom through RUU_Ville_U_JB_45_S_HTC_Europe_3.16.401.8_Radio_1.11.50.05.28_10.27.50.08L_release_301814_signed_2_4.
befor doing this I had supercid and s-off
After launching ruu ,the process stopped by error 159.
I tried other RUU_Ville_U_ICS_40_S_HTC_Europe_2.31.401.5_Radio_1 .06es.50.02.31_10.09a.50.04L_release_275655_signed
this flashed fine and worked good.
but i wanted JB so i downloaded OTA_Ville_U_JB_45_S_HTC_Europe_3.16.401.8_1.11.50.05.28_10.27.50.08L_release_301852xf01hejl416oev96
and flashed it by CWM
but in the cwm enviroment , process stopped saying cid check failed....(and a couple of cid es)
So I changed my CID to stock (HTC_203) and I went through all above steps againe but same errors......
I don't know where the problem is??
Click to expand...
Click to collapse
hm.. which hboot do you have?
try to run the ics ruu again, after this you have stock ics rom right? do a factory reset and be sure that you have flashed the stock recovery.
then apply the ota update and install it the normal way.
I'm not sure if the ota updates are flashable so easily with custom recovery.
NQNH said:
hm.. which hboot do you have?
try to run the ics ruu again, after this you have stock ics rom right? do a factory reset and be sure that you have flashed the stock recovery.
then apply the ota update and install it the normal way.
I'm not sure if the ota updates are flashable so easily with custom recovery.
Click to expand...
Click to collapse
Yes ...I have ICS now....
sorry but what do you mean by normal way....
shoud I flash stock recovery separately?
what is the normal way of installing ota?
I thought that the usual way is using CWM.
salar_bigharar2009 said:
Yes ...I have ICS now....
sorry but what do you mean by normal way....
shoud I flash stock recovery separately?
what is the normal way of installing ota?
I thought that the usual way is using CWM.
Click to expand...
Click to collapse
hm..
the normal would be (if everything is stock)
boot your phone, search for updates, download update, apply update and the rest is an automatically process.
as far as I know you only have to be on stock recovery to be able to install the ota.
so, flash the stock recovery
https://www.dropbox.com/s/btmsslfgbwegu2k/ville_recovery_signed.img
look for updates again, and after download, tap on "install update" or sth like that.
your phone should restart in recovery mode and install the update.
but you have to be on stock recovery.
give it a try and let me know if this way worked
it should
aaaand I recommend you to do a factory reset after the JB update.
boot your phone after the update to your bootloader and select factory reset.
after this procedure you can flash back your favourite custom recovery and do whatever you want
ojoydro occasions
salar_bigharar2009 said:
Yes ...I have ICS now....
sorry but what do you mean by normal way....
shoud I flash stock recovery separately?
what is the normal way of installing ota?
I thought that the usual way is using CWM.
Click to expand...
Click to collapse
And i forgot my hboot is1.14.0002
salar_bigharar2009 said:
And i forgot my hboot is1.14.0002
Click to expand...
Click to collapse
oh I forgot.
change your cid to HTC__001
its the regionfree one for EU
should work with the ota
Thank you man .....after running Ics ruu ,i flashed stock recovery and installed ota jb zip from recovery ....(After entering to recovery, holded volum up and power button and the menu displayed)
During this my cid was stock:htc_203
Sent from my HTC One S using xda premium