Related
Hi all
I have new Samsung Dart (android)- the device won't turn on after I installed ClockworkMod,
I tried to add addition language fonts to the phone,
I rooted the device first,
Then i installed "ClockworkMod"
I tried removing the battery, holding the power+volume down for 30 sec
nothing....
any advice will be welcomed.
Thanks
did you try putting the battery back in and holding vol up and power to boot into recovery?
Sent from my MB860 using xda premium
shark669 said:
Hi all
I have new Samsung Dart (android)- the device won't turn on after I installed ClockworkMod,
I tried to add addition language fonts to the phone,
I rooted the device first,
Then i installed "ClockworkMod"
I tried removing the battery, holding the power+volume down for 30 sec
nothing....
any advice will be welcomed.
Thanks
Click to expand...
Click to collapse
well i think it is hard bricked just go to the service center act like a fool dont say any thing about recovery . Tell them any story and youll get it reparied
Sent from my GT-S5670 using xda premium
konna280 said:
did you try putting the battery back in and holding vol up and power to boot into recovery?
Click to expand...
Click to collapse
Made me laugh
Did you ever get anything on the screen when trying to power on again? How did you install clockworkmod, and what version did you use? Also what is the source link to the clockworkmod that you used?
If you can get back into download mode on your phone, you can find the stock roms/tools/directions at
http://www.madteam.co/forum/development-70/(archive)-stock-roms-and-tools/
>>Did you ever get anything on the screen when trying to power on again
Nothing, its Dead like a rock
Will USB Jig help? or 300K resistor?
Thank you!
Sounds like you will have to send it in for repair. I don't think that a jig will help you.
Where did you get CWM from, and what version? Was it for the T499 or for S5570?
The Phone is bricked. I killed mine too flashing the clockwork mod, it did not belong on this phone. I think the phone is not on the list because it is not supported. The only way to fix it is to re install the factory boot loading files thought the service pins in the back of the circuit board using a special tool. I'm looking at mine as I type. Oh well, it happens, I just went ahead and bought an used HD2.
For anyone that does want CWM on the SGH-T499, have a look here http://www.madteam.co/forum/development-70/(development)-clockworkmod-recovery-for-sgh-t499/
Hello everybody,
I hope that someone can give me some advise to get my tf300t up and running again. I wanted to install cm10.2 but I wanted to install CWM first.
I unlocked my device first with the unlock app v8 from asus.
I tried to install CWM the first time but it did not work.
I went back into recovery mode but I wasn't paying attention and pressed wipe userdata
Now my tf300t only shows the ASUS logo and the text that the device is unlocked. I can't get back in recovery mode anymore. Is there a way the restore it back to default?
I hope that someone can help me out.
Thank you in advance for your time and effort.
Regards
Burner1977
burner1977 said:
Hello everybody,
I hope that someone can give me some advise to get my tf300t up and running again. I wanted to install cm10.2 but I wanted to install CWM first.
I unlocked my device first with the unlock app v8 from asus.
I tried to install CWM the first time but it did not work.
I went back into recovery mode but I wasn't paying attention and pressed wipe userdata
Now my tf300t only shows the ASUS logo and the text that the device is unlocked. I can't get back in recovery mode anymore. Is there a way the restore it back to default?
I hope that someone can help me out.
Thank you in advance for your time and effort.
Regards
Burner1977
Click to expand...
Click to collapse
Can you get to the menu with the recovery options, boot android, USB, and wipe data? You can use fastboot from there.
cmendonc2 said:
Can you get to the menu with the recovery options, boot android, USB, and wipe data? You can use fastboot from there.
Click to expand...
Click to collapse
thank you for your response. No I can't get in there. any suggestions?
thx for your advise
burner1977 said:
thank you for your response. No I can't get in there. any suggestions?
thx for your advise
Click to expand...
Click to collapse
If you cant get into there, you cant really use fastboot. Unless you made NvFlash Backups beforehand, I don't think there is much else you can do, since the recovery isn't working either.
cmendonc2 said:
If you cant get into there, you cant really use fastboot. Unless you made NvFlash Backups beforehand, I don't think there is much else you can do, since the recovery isn't working either.
Click to expand...
Click to collapse
I stupidly made no backups so what you are saying is that it is done.
burner1977 said:
I stupidly made no backups so what you are saying is that it is done.
Click to expand...
Click to collapse
I've spent a lot of time searching and it seems like that's it...
I'm on Asus screen, I can reboot it by either holding down pwr button until it reboots, or using reset switch with a paperclip. vol - does nothing, just reboots to asus screen...computer sees nothing. vol + goes into APX mode (blank screen)...computer detects with correct drivers. I've tried draining battery completely...disconnecting battery for a few days...same result.
If I had to speculate...maybe at some point someone will figure out how to use another's backup files and push them to the device in APX mode.
I've looked into replacing the motherboard...and have seen some for as low as 50$ on ebay. Personally, swapping them would be easy...but some may not have the caviler attitude with hardware swapping. Just gotta get the wife to agree to spend the $.
I'd die for a free fix, the kids really miss playing with the thing
coppervines said:
I've spent a lot of time searching and it seems like that's it...
I'm on Asus screen, I can reboot it by either holding down pwr button until it reboots, or using reset switch with a paperclip. vol - does nothing, just reboots to asus screen...computer sees nothing. vol + goes into APX mode (blank screen)...computer detects with correct drivers. I've tried draining battery completely...disconnecting battery for a few days...same result.
If I had to speculate...maybe at some point someone will figure out how to use another's backup files and push them to the device in APX mode.
I've looked into replacing the motherboard...and have seen some for as low as 50$ on ebay. Personally, swapping them would be easy...but some may not have the caviler attitude with hardware swapping. Just gotta get the wife to agree to spend the $.
I'd die for a free fix, the kids really miss playing with the thing
Click to expand...
Click to collapse
I'm on the same boat, this morning I was trying to install CyanogenMod following the instructions and wipped the tablet... I only have APX connection now with no backups...
Alright i got 6 hours before tmbobile store opens and i can HOPEFULLY get an exchange, but not banking on it. btw im new to rooting so i wasnt familiar with the process, but regardless i have hard bricked my NEXUS 5. Title says the problem. I followed wwjoshdew's guide to rooting on youtube, and rooted successfully. But i could'nt for the life of me figure out how to create nandroid. I ended up realizing i didnt download cmw recovery mode and downloaded it from the play store. the app took me to a button that said flash recovery and i hit it and my phone asked for permission from unknown source, i hit ok and it shut down, on 70% battery life. Not turning on please help
Try to boot the phone into bootloader mode. Just hold volume down and the power button. From there try to cycle to recovery. You use your volume down to cycle through the options and power but as select. If you can boot into recovery and have that successfully installed then you can erase your phone and try to power it on from there. If you didn't successful install the custom recovery then you'll have the standard Android recovery. You can erase everything from that too.
These phones are hard to brick and not be able to fix it.
Sent from my Nexus 5 using XDA Premium 4 mobile app
ruben8448 said:
Try to boot the phone into bootloader mode. Just hold volume down and the power button. From there try to cycle to recovery. You use your volume down to cycle through the options and power but as select. If you can boot into recovery and have that successfully installed then you can erase your phone and try to power it on from there. If you didn't successful install the custom recovery then you'll have the standard Android recovery. You can erase everything from that too.
These phones are hard to brick and not be able to fix it.
Sent from my Nexus 5 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
Doesn't turn on dude. No matter what. I am new to roms but i know what a hard brick is.
You should really read the guides and stickied threads at the top of these forums. The guides are very noob friendly and you wouldn't have bricked your phone. There's one to reset your device to stock as well. There's really no need for this thread and on top of that there is a sticky that says no questions in the General forums.
Sent from my Nexus 5 using Tapatalk
Determine your phone is actually off. Plug your phone into charge, if a battery sign appears in the middle of the screen then your phone is off.
If your phone is off, hold down the volume down button with the power button to start the bootloader, press volume down twice and press the power button to enter recovery.
If your screen remains black and doesn't show a battery logo, hold the volume up, volume down and power buttons at the same time for a minute, then let go and hold down the power button. Which should hopefully start your phone.
FuMMoD said:
You should really read the guides and stickied threads at the top of these forums. The guides are very noob friendly and you wouldn't have bricked your phone. There's one to reset your device to stock as well. There's really no need for this thread and on top of that there is a sticky that says no questions in the General forums.
Sent from my Nexus 5 using Tapatalk
Click to expand...
Click to collapse
You should have been around long enough to know that when newbies break their new toys they go nuclear and dismiss all the information around them.
BNNEBULA said:
Alright i got 6 hours before tmbobile store opens and i can HOPEFULLY get an exchange, but not banking on it. btw im new to rooting so i wasnt familiar with the process, but regardless i have hard bricked my NEXUS 5. Title says the problem. I followed wwjoshdew's guide to rooting on youtube, and rooted successfully. But i could'nt for the life of me figure out how to create nandroid. I ended up realizing i didnt download cmw recovery mode and downloaded it from the play store. the app took me to a button that said flash recovery and i hit it and my phone asked for permission from unknown source, i hit ok and it shut down, on 70% battery life. Not turning on please help
Click to expand...
Click to collapse
You bricked a Nexus?
Hold down Volume Down, Up, and Power to get into fastboot mode. Restore from Factory Image.
Normally, to root a nexus, I fastboot Team Win Recovery Project.
Anyways what you did simply could not HARD BRICK the phone.
zeekiz said:
You should have been around long enough to know that when newbies break their new toys they go nuclear and dismiss all the information around them.
Click to expand...
Click to collapse
Seriously lol. Even though the guides are right there in their faces.
Sent from my Nexus 5 using Tapatalk
HELP SOS
FuMMoD said:
You should really read the guides and stickied threads at the top of these forums. The guides are very noob friendly and you wouldn't have bricked your phone. There's one to reset your device to stock as well. There's really no need for this thread and on top of that there is a sticky that says no questions in the General forums.
Sent from my Nexus 5 using Tapatalk
Click to expand...
Click to collapse
My Nexus5 doesn't flash the Led light or enter bootloader and software . I was flashing the based CM kernel and i followed the instructions nicely, while using TWRP Recovery i pressed reboot system after the flash and the phone suddenly died. I connected it to the PC and the installing drivers popup appeared and it didn't install them, problem(QHSUSB_BULK) it only appeared once. And since that, phone is dead. PLEASE HELP!!!!
Yazan Abzakh171 said:
My Nexus5 doesn't flash the Led light or enter bootloader and software . I was flashing the based CM kernel and i followed the instructions nicely, while using TWRP Recovery i pressed reboot system after the flash and the phone suddenly died. I connected it to the PC and the installing drivers popup appeared and it didn't install them, problem(QHSUSB_BULK) it only appeared once. And since that, phone is dead. PLEASE HELP!!!!
Click to expand...
Click to collapse
Do you have a link to the kernel you flashed? I think you done bricked it good.
Were you using this method?
http://www.youtube.com/watch?v=w3beFx-3Ic4
If yes,I think then all Nexus 5 users should be warned about CF's autoroot issues,because I see more and more topics related to this issue.
Simonna said:
Were you using this method?
http://www.youtube.com/watch?v=w3beFx-3Ic4
If yes,I think then all Nexus 5 users should be warned about CF's autoroot issues,because I see more and more topics related to this issue.
Click to expand...
Click to collapse
I don't believe the issues you're seeing, appears to be failed emmc, is related to chain fire's auto root. Cf is probably the most popular method to root and it's a coincidence. I've seen these failures with other root methods too.
I think the op flashed a kernel not for his device.
jd1639 said:
I don't believe the issues you're seeing, appears to be failed emmc, is related to chain fire's auto root. Cf is probably the most popular method to root and it's a coincidence. I've seen these failures with other root methods too.
I think the op flashed a kernel not for his device.
Click to expand...
Click to collapse
I am not a developer so bear with me. I'm just a guy in mpls with a completely stock N5 from Google Play that encountered similar issue as the original post. There was no damage or water issue, or other problem prior to going dead. It had about 50% battery and maybe 15 minutes after reading an email it was dead when I looked at it again. It just simply turned off while in my pocket. I could not get it to power on or enter bootloader or a recovery screen. After a week of trying to charge via USB and the original wall charger and countless attempts to hold power and volume buttons without success, I decided to pop the back off and disconnected the battery. I put it back together, but that made no difference either. Google play will send me a new phone, but I'd like to get it fired up and extract the last week or so of pics. Any ideas? Again, I am a complete noob and this 3 month old phone has not been modified in any way, other than auto updates from Google play. Thanks for any assistance or guidance.
elf1967 said:
I am not a developer so bear with me. I'm just a guy in mpls with a completely stock N5 from Google Play that encountered similar issue as the original post. There was no damage or water issue, or other problem prior to going dead. It had about 50% battery and maybe 15 minutes after reading an email it was dead when I looked at it again. It just simply turned off while in my pocket. I could not get it to power on or enter bootloader or a recovery screen. After a week of trying to charge via USB and the original wall charger and countless attempts to hold power and volume buttons without success, I decided to pop the back off and disconnected the battery. I put it back together, but that made no difference either. Google play will send me a new phone, but I'd like to get it fired up and extract the last week or so of pics. Any ideas? Again, I am a complete noob and this 3 month old phone has not been modified in any way, other than auto updates from Google play. Thanks for any assistance or guidance.
Click to expand...
Click to collapse
So, your phone doesn't turn on at all?
jd1639 said:
I don't believe the issues you're seeing, appears to be failed emmc, is related to chain fire's auto root. Cf is probably the most popular method to root and it's a coincidence. I've seen these failures with other root methods too.
I think the op flashed a kernel not for his device.
Click to expand...
Click to collapse
Correct. No symbols, no battery icon, no vibrate, etc.
elf1967 said:
Correct. No symbols, no battery icon, no vibrate, etc.
Click to expand...
Click to collapse
I'm afraid there's nothing you can do. It would have to at least get into recovery or bootloader to have a prayer.
jd1639 said:
I'm afraid there's nothing you can do. It would have to at least get into recovery or bootloader to have a prayer.
Click to expand...
Click to collapse
Thanks - was just hoping it was not a hardware failure given the posts about difficulty bricking N5. Any chance if I bought a new battery that came charged it would fire up or replacing the motherboard an option?
p.s. I am not the original poster so not sure if I ticked someone off or not, sorry if I did. Just looking for assistance
elf1967 said:
Thanks - was just hoping it was not a hardware failure given the posts about difficulty bricking N5. Any chance if I bought a new battery that came charged it would fire up or replacing the motherboard an option?
p.s. I am not the original poster so not sure if I ticked someone off or not, sorry if I did. Just looking for assistance
Click to expand...
Click to collapse
It sure sounds like a hardware failure. Doubt a different battery would help. And don't worry about being the original op. This thread is old
jd1639 said:
It sure sounds like a hardware failure. Doubt a different battery would help. And don't worry about being the original op. This thread is old
Click to expand...
Click to collapse
I get the unknown device driver when hooked up USB to computer (QHSUSB_BULK). Think it is worth waiting a few weeks prior to returning it to see if there is a way to access the flash memory via a driver download? Searches for help showed similar unknown driver problem workable on samsung and HTC last year (QHSUSB_DLOAD)
elf1967 said:
I get the unknown device driver when hooked up USB to computer (QHSUSB_BULK). Think it is worth waiting a few weeks prior to returning it to see if there is a way to access the flash memory via a driver download? Searches for help showed similar unknown driver problem workable on samsung and HTC last year (QHSUSB_DLOAD)
Click to expand...
Click to collapse
No, you won't be able to. The memory doesn't mount like a sd card would. For the future use something like drop box or Google drive too backup your photos as you take them.
Hey guys, I recently found my tf300t tucked away somewhere. Haven't used it for absolute months! And I remembered why, I kept having problems with CM somehow(I believe the last update was somewhere in June-July of 2013), so this time after charging it and wanting to do it all again, I figured I'd get it updated. Seeing as it's been nearly a year and so much crap has changed, I figured something was going to go wrong. Before I even DID ANYTHING, I told the tablet to reboot into recovery mode, and boom that's where I'm stuck. The Tablet rebooted and now only shows the Asus boot screen... Nothing else! Vol down+pwr didn't work, nothing. And If I hold the power button it shuts off but then turns right back on 1-2 seconds later. I'm not sure what this is, a soft brick? a Brick? just an error? Can anybody please help? I know this is probably the wrong section, but I'm just frustrated.
Thank you to anybody who can help in any shape or form.
PS: no bashing is needed, my tables already bashing my head for me.
Amirocassar said:
Hey guys, I recently found my tf300t tucked away somewhere. Haven't used it for absolute months! And I remembered why, I kept having problems with CM somehow(I believe the last update was somewhere in June-July of 2013), so this time after charging it and wanting to do it all again, I figured I'd get it updated. Seeing as it's been nearly a year and so much crap has changed, I figured something was going to go wrong. Before I even DID ANYTHING, I told the tablet to reboot into recovery mode, and boom that's where I'm stuck. The Tablet rebooted and now only shows the Asus boot screen... Nothing else! Vol down+pwr didn't work, nothing. And If I hold the power button it shuts off but then turns right back on 1-2 seconds later. I'm not sure what this is, a soft brick? a Brick? just an error? Can anybody please help? I know this is probably the wrong section, but I'm just frustrated.
Thank you to anybody who can help in any shape or form.
PS: no bashing is needed, my tables already bashing my head for me.
Click to expand...
Click to collapse
Does it respond to being plugged into a computer? Try pressing the reset button and then doing the vol down to get into fastboot.
cmendonc2 said:
Does it respond to being plugged into a computer? Try pressing the reset button and then doing the vol down to get into fastboot.
Click to expand...
Click to collapse
Nope, but I am running W8 and I read that W8 kinda sucks for this sort of thing. Like you need W7 or XP? Correct me if im wrong. Any other ideas? . I didn't do anything! Just told it to reboot into recovery, and now I'm stuck there. I held pwr+volume down and it still keeps stuck, and if I try to power it off then it just turns on again a few seconds later.
Amirocassar said:
Nope, but I am running W8 and I read that W8 kinda sucks for this sort of thing. Like you need W7 or XP? Correct me if im wrong. Any other ideas? . I didn't do anything! Just told it to reboot into recovery, and now I'm stuck there. I held pwr+volume down and it still keeps stuck, and if I try to power it off then it just turns on again a few seconds later.
Click to expand...
Click to collapse
I have the same issue more or less...
Mine will not go into fastboot
kingrat said:
I have the same issue more or less...
Mine will not go into fastboot
Click to expand...
Click to collapse
I also have this issue
??
So none of you can get to fastboot or recovery, but you do all get the stuck at Asus logo?? All your bootloaders are unlocked?? All of you got to this spot, the same way by not using the tablet for long periods of time???? What bootloader are you on?? What version of CM are you running??? What is the OS of your PC, If its not the top 3 please be specific......Are you using a stock asus data cable??
Sounds similar
From what your posts say, it sounds like something i came across. I struggled for hours trying to figure out this dilemma, but if you're in the same situation i was in then as long as you're in that screen even after trying to hold the power and -vol let it sit there, plug in and make sure you have all your files associated with fastboot platform installed and try pushing the new TWRP ( http://www.androidfilehost.com/?fid=23329332407569892 ) to your tablet, for some reason after a certain update after 4.1 i believe? CWM stopped working for me, so try pushing the new TWRP from that link there and possibly you should be able to gain control of your tablet again and start installing the new packets for CM 11. I found this to be very helpful http://forum.xda-developers.com/showthread.php?t=2570965 and thanks to "cmendonc2", 6 post down, he really cleared things up with his simple links. Hope you're in the same boat as i was. Good luck
Hi thanks for reading, I will tell you as quick as I can
Basically I got this Allwinner A31 Tablet Q102 and wanted to root it and flash it when I got it, so I got it only a week ago, week ago from tommorow.
I managed to root it with VRoot and then attempted to install CWM because ROM Manager would say that it isnt supported. So after tons of research I took the method of rooting an Onda tablet which was to use the ADB. I got the Recovery.tar extracted the files inside it and then did the
adb push /data/recovery.img
And stuff like that
After I did all that it told me to hold the VOL+/POWER to enter CWM, I held it for like 1 minute until CWM showed and it was working. CWM version was 6.0.2.7 I think. So I was like oh ok its working now. So then I rebooted the system using the first option CWM gave me. After it turned off it didnt turn back on. So I turned it on manually and all I see is a blank BLACK screen. Thats it. It hangs and does nothing. Cant enter Recovery, safe mode, the USB is not recognized. Infact it doesnt even connect anymore.
If I hold the power button, it turns off then once I let go it turns back on doing the same thing.
Please help me as I only just got the Tablet and can't afford to lose it. Theres too many files I need to keep, only some were moved to the SD card.
4.4.2 KitKat
addy187a said:
Hi thanks for reading, I will tell you as quick as I can
Basically I got this Allwinner A31 Tablet Q102 and wanted to root it and flash it when I got it, so I got it only a week ago, week ago from tommorow.
I managed to root it with VRoot and then attempted to install CWM because ROM Manager would say that it isnt supported. So after tons of research I took the method of rooting an Onda tablet which was to use the ADB. I got the Recovery.tar extracted the files inside it and then did the
adb push /data/recovery.img
And stuff like that
After I did all that it told me to hold the VOL+/POWER to enter CWM, I held it for like 1 minute until CWM showed and it was working. CWM version was 6.0.2.7 I think. So I was like oh ok its working now. So then I rebooted the system using the first option CWM gave me. After it turned off it didnt turn back on. So I turned it on manually and all I see is a blank BLACK screen. Thats it. It hangs and does nothing. Cant enter Recovery, safe mode, the USB is not recognized. Infact it doesnt even connect anymore.
If I hold the power button, it turns off then once I let go it turns back on doing the same thing.
Please help me as I only just got the Tablet and can't afford to lose it. Theres too many files I need to keep, only some were moved to the SD card.
4.4.2 KitKat
Click to expand...
Click to collapse
So,Wrong discussion area...Anyway
You're still under warranty,why dont you just RMA it?
just dont tell them you're rooted or anything mess with softwares.
androidvillage said:
So,Wrong discussion area...Anyway
You're still under warranty,why dont you just RMA it?
just dont tell them you're rooted or anything mess with softwares.
Click to expand...
Click to collapse
Hi, thanks for the replay, the business wouldnt replace it but they offered to have a look, I know its bricked so there is no point sending it there. I hear you can fix it in Phoenix Suite but I cant find the firmware for it.
Btw what should it be in, I had trouble sorting it lol
addy187a said:
Hi, thanks for the replay, the business wouldnt replace it but they offered to have a look, I know its bricked so there is no point sending it there. I hear you can fix it in Phoenix Suite but I cant find the firmware for it.
Btw what should it be in, I had trouble sorting it lol
Click to expand...
Click to collapse
Ok but....what is the actual model of this thing?
androidvillage said:
Ok but....what is the actual model of this thing?
Click to expand...
Click to collapse
Took ages to find out, but its called an Allwinner Q102 something with YBC, Ive heard of a similar one called Allwinner A31s Yonestoptech and was also a Q102
Hey,
What's up with your tablet? I own the same model and was thinking about installing cyanogenmod, but I have no idea yet. Have you managed to figure something out, or found any way to repair it?
Cheers!
flash ??
Try to flash the stock ROM.......
Nah man, I can't do anything with it. Turn it on just a black screen. Holding the volume down button then pressing Tue power button a couple of times makes my computer detect the tablet. But nothing else.
I cannot enter CWM, after I flashed CWM it said Can't mount boot.IMG can't Mount this and that and then I restarted it and it happened.
SO DONT FLASH ANY CWM OR ROMS ON IT.
I really want the tablet fixed man. What the hell do I do?
Sent from my HTC One using XDA Free mobile app
Try this mate
slatedroid.com/topic/40623-aml-flash-tool-aka-imageburntool/
Sent from my GT-P5210 using XDA Free mobile app
@addy187a - Did you get it done?
I have the same problem.... - I installed successfully twrp, did a backup, wiped and tried to install another rom - failed. Now I am not able to boot into recovery - it is black, not recognized by the system (so I can't use imageburntool).
It starts, is black illuminated, nothing happens, only power is possible
my device: Fusion5 F5CS 32GB, Q102, 32GB
..no idea what to do...
Hey, I know I'm 1 year late to reply but I only just logged in to XDA since ages! I know right? Anyway, the way I fixed it was to download the firmware for the tablet which I found out by keeping a note about tablet model number (Settings> About device> Model) and spent a couple minutes searching for the firmware for it. Then I used Phoenix suite or just Phoenix can't remember what it was called to flash the tablet. There are plenty of YouTube videos and instructions on the web of how to use it, I can't remember how I did it as this was over a year and a half ago! It's as simple as that and words cannot describe how relieved I felt after reviving it. If an admin sees this, please close the thread. I'm still finding out how to use this site.