Novice here.
Ran the All-in-One utility today and after the CWM installed I hit "Perm root" without reading the thing below telling me to boot to recovery first. It's now stuck in boot loop. Everything went off fine up until the Perm root. Even that said successful and then restarted. Only after the process was completed did the recovery loop begin. No HTC logo loop. Just reboots into CWM over and over no matter what technique I use (except for opening the case).
I've read this: http://forum.xda-developers.com/showthread.php?t=1599363
And am trying to install ADB to push ANY possible ROM over to the SD card. My recovery allows the toggle of /mount sdcard and /mount system, however adb fastboot push doesn't work. "error: device not found"
And I can't do this: http://forum.xda-developers.com/showthread.php?t=1644730 because my phone is stuck in the recovery loop. If I try volume down + power, it just comes back to recovery screen. I've tried factory reset, I've tried wiping cache, I've tried wiping Dalvik, and still nothing. I did flash the SuperSu.zip after I had used the Perm Root button on Haroon2000's app.
I'm incredibly flustered as I've rooted devices for years and this is my first problem. I've seen similar complaints all with ideas of breaking into the phone and unplugging it's battery so I can get to the bootloader etc, but I'm so very confused. So many posts telling me to do so many things.
Can someone please help break down a tangible solution here? I'm freaking out.
Cheers
EDIT: If someone can get my phone fixed, I'll Paypal them $50 USD. I really need my phone back ASAP :\
I don't know if this is your solution, but you did not mention it as one of your attempts.
Have you looked into running an RUU?
Sent from my HTC One S using xda premium
beats4x said:
I don't know if this is your solution, but you did not mention it as one of your attempts.
Have you looked into running an RUU?
Sent from my HTC One S using xda premium
Click to expand...
Click to collapse
I'll update this again once I try breaking the phone down and yanking the battery. But I have tried running the RUU. I can't get to the bootloader right now and it's not listing the device when I adb devices.
I'm going to go home from work since I've spent 7 hours on two machines (XP/7) trying to fix this PoS and redo everything from the ground up. Hopefully my anger will have overcome it.
Something I've noticed however, is that within the CWM recovery, I can use the All-in-one tool to reboot the phone. So it is reacting to ADB commands. Perhaps trying to use ADB fastboot (Right-click method) instead of full ADB installation could be a problem with trying to push a ROM zip. Also, as far as the RUU goes. I don't remember what happened there. I'll edit this when I get home.
nik.the said:
I'll update this again once I try breaking the phone down and yanking the battery. But I have tried running the RUU. I can't get to the bootloader right now and it's not listing the device when I adb devices.
I'm going to go home from work since I've spent 7 hours on two machines (XP/7) trying to fix this PoS and redo everything from the ground up. Hopefully my anger will have overcome it.
Something I've noticed however, is that within the CWM recovery, I can use the All-in-one tool to reboot the phone. So it is reacting to ADB commands. Perhaps trying to use ADB fastboot (Right-click method) instead of full ADB installation could be a problem with trying to push a ROM zip. Also, as far as the RUU goes. I don't remember what happened there. I'll edit this when I get home.
Click to expand...
Click to collapse
Okay, update.
I was able to get ADB working and detect my phone.
Next, I was able to push Venom Rom to phone. I factory reset, wiped cache, wiped Dalvik, and was able to install Venom.zip. It then asked to reboot (per Venom screen) and I said okay. It then returned to CWM Recovery. I was confused but left everything as is. I have now reset the phone by holding the power button for around 10 seconds. It then restarted to the HTC Quietly Brilliant screen. I have been looking at that screen for about 5 minutes.
Also pertinent: I did try to run the RUU, but it didn't connect through USB. (I forget what it said verbatim). So that didn't work. I also was able prior to this entire process get into the bootloader via dumb luck.
Any suggestions? I am staring at the HTC boot screen still. Do I try to restart and enter bootloader? If so, then what? It seems there is something wrong with CWM. Can I switch recoveries? Can I uninstall it?
Calm down we have all been there,
When you flashed venom did you flash the boot image? Also i use twrp instead of cwm i find twrp better .
To enter bootloader hold power button and down vol together .
As gazknight said, this seems like proper kernel not being flashed or having an issue. If you flashed the boot.img with fastboot, try again erasing cache from fastboot first. The commands are as follow:
fastboot erase cache
fastboot flash boot boot.img (where this boot.img is the one inside the zip from the rom you choose and must be left in the same folder than fastboot)
It happened to me a couple times when i was on hboot 1.14 that I had to flash the boot.img a second time sometimes, somehow it was not working the first time, randomly, even though the flash had completed ok on fastboot.
If still doesn't work try doing a factory reset from TWRP and flashing ViperOneS again.
If that still doesn't work, you might want to try another rom, like TrickDroid, you would then have to flash the boot.img from this other room with fastboot, remember that.
Try and let us know
Hold down volume down while you're trying to boot, that will get you in boot loader, go to fast boot by pressing the power key, connect your phone to your computer, run the flash viper boot img thingy and you're set!
Envoyé depuis mon HTC One S avec Tapatalk
Same issue with HTC One S bricked but in European version, Stock ROM
hello,
I did't want to start a new topic, as I'm experiencing a similar issue with my HOS. Briefly, yesterday morning I plug the phone from charger at 06.00 am. Play with it for a while and then go to work. Used it at work for a few phone calls until 10.00 am (so 4 hours on fully charge battery). Then at 10.00 am I went into a meeting and left the phone out of my sight for 20-30 minutes. When I came back from the meeting I realize that the phone was closed. I try to open it (power button) but nothing. Press power for 10-30 seconds with volume down - still no effect.
Then I took the charger (the original one that I always use to cherge it) and plug it, left it for 2-3 minutes and press power. The phone starts but all I have is the white screen with HTC logo and if I press the power button + volume down the phone goes into bootloader. That's all I can do with it for now.
I have stock rom, bootloader is locked and I never try to root the phone. Is it any chance to repair it by myself or I have to sent it to the repair shop.
many thanks in advance.
Alright so I feel like I'm getting closer.
Here's whats happening now. It's in the HTC boot screen loop. I can get it into bootloader whenever I want, but now it's not detecting /sdcard in recovery. Within the bootloader, fastboot won't detect my device and my computer (Windows 8) claims the device is malfunctioning. I can still use fastboot adb commands from my computer when it is in recovery. I have gone into bootloader and cleared storage, as well as factory reset after. Also, it used to reboot into recovery endlessly. Now it appears that isn't hte case and reboots from recovery into the OS, but will not work.
I'm going to try and flash using adb w/o sdcard the boot.img as suggested above. I'll keep updating so others can know the process if they soft-brick their phone (I'm assuming this is a soft brick because I can still run things etc).
Update: trying to do fastboot erase cache from within recovery gives me "Waiting for device". As I've said, for some reason, it says the device is malfunctioning/not detected when I'm in the 1.14 Hboot Bootloader. But again, I can issue adb devices from within recovery. Sdcard still not mounting.
Edit: I'm issuing adb commands through adbfastboot files. Do I need to have the Android SDK fully installed with the Manager thing, or does the basic adbfastboot work (From here: http://www.htconeforum.com/forum/ht...e-your-htc-one-s-back-100-stock-relocked.html). That adb fastboot has the following files: adb, fastboot, adbwinapi.dll, adbwinusbapi.dll.
I think the source of the current problem is that I can no longer access my /sdcard or mount it. One step forward, then two steps back -_-.
nik.the said:
Alright so I feel like I'm getting closer.
Here's whats happening now. It's in the HTC boot screen loop. I can get it into bootloader whenever I want, but now it's not detecting /sdcard in recovery. Within the bootloader, fastboot won't detect my device and my computer (Windows 8) claims the device is malfunctioning. I can still use fastboot adb commands from my computer when it is in recovery. I have gone into bootloader and cleared storage, as well as factory reset after. Also, it used to reboot into recovery endlessly. Now it appears that isn't hte case and reboots from recovery into the OS, but will not work.
I'm going to try and flash using adb w/o sdcard the boot.img as suggested above. I'll keep updating so others can know the process if they soft-brick their phone (I'm assuming this is a soft brick because I can still run things etc).
Update: trying to do fastboot erase cache from within recovery gives me "Waiting for device". As I've said, for some reason, it says the device is malfunctioning/not detected when I'm in the 1.14 Hboot Bootloader. But again, I can issue adb devices from within recovery. Sdcard still not mounting.
Edit: I'm issuing adb commands through adbfastboot files. Do I need to have the Android SDK fully installed with the Manager thing, or does the basic adbfastboot work (From here: http://www.htconeforum.com/forum/ht...e-your-htc-one-s-back-100-stock-relocked.html). That adb fastboot has the following files: adb, fastboot, adbwinapi.dll, adbwinusbapi.dll.
I think the source of the current problem is that I can no longer access my /sdcard or mount it. One step forward, then two steps back -_-.
Click to expand...
Click to collapse
You might need to do it as administrator.
I think I've got it. One last tip. All of the above has been helpful, but I think the problem was trying to use my Windows 8 laptop. The second I got to work, I plugged it in on the bootloader to my XP machine and voila! it recognized fastboot and listed devices.
I have tried to run the RUU 2.35.531.7 but just like unrooting my old phone, I had issues because that update was already on this phone, so it goes through the entire process only to tell me on the windows XP utility that it had failed because it was the wrong update. When I did this to my old One S right before I sent it into Tmobile for warranty, it did the same thing with the 1.53 RUU, then when I found the 2.35, it worked like a charm.
So my last question (hopefully) then is, am I missing something as for installing an OLD or exact same RUU? Or is there a newer one than the 2.35.531.7?
I haven't tried on a Windows 7 machine, but I have one available here at work. I'm wondering if I should try to fastboot a ROM. Any suggestions what I can do to get it back to stock, or an old old stock version? I'd like to root it so I can use my Titanium Backup.
Update: Before ending this reply, I read that the RUU may be failing because the bootloader is unlocked/tampered still. I'm going to run it again to grab the error code to make sure of the issue, because it seems you should be able to revert or use any RUU (correct?).
nik.the said:
I think I've got it. One last tip. All of the above has been helpful, but I think the problem was trying to use my Windows 8 laptop. The second I got to work, I plugged it in on the bootloader to my XP machine and voila! it recognized fastboot and listed devices.
I have tried to run the RUU 2.35.531.7 but just like unrooting my old phone, I had issues because that update was already on this phone, so it goes through the entire process only to tell me on the windows XP utility that it had failed because it was the wrong update. When I did this to my old One S right before I sent it into Tmobile for warranty, it did the same thing with the 1.53 RUU, then when I found the 2.35, it worked like a charm.
So my last question (hopefully) then is, am I missing something as for installing an OLD or exact same RUU? Or is there a newer one than the 2.35.531.7?
I haven't tried on a Windows 7 machine, but I have one available here at work. I'm wondering if I should try to fastboot a ROM. Any suggestions what I can do to get it back to stock, or an old old stock version? I'd like to root it so I can use my Titanium Backup.
Update: Before ending this reply, I read that the RUU may be failing because the bootloader is unlocked/tampered still. I'm going to run it again to grab the error code to make sure of the issue, because it seems you should be able to revert or use any RUU (correct?).
Click to expand...
Click to collapse
The bootloader does need to be relocked for the RUU too work and the RUU you used before should work because I have used the same RUU a few times and it worked fine.
Darknites said:
The bootloader does need to be relocked for the RUU too work and the RUU you used before should work because I have used the same RUU a few times and it worked fine.
Click to expand...
Click to collapse
I'll try that. thanks.
Now on the same XP computer, it's not showing when I adb devices, however it does show in device manager. This changed after trying to do the RUU without relocking.
Yeah! Fixed!
After enough toggling, I changed the recovery to the T one and relocked my bootloader. It turns out detecting the device wasn't necessary somehow. Then I ran the RUU and voila!
nik.the said:
I'll try that. thanks.
Now on the same XP computer, it's not showing when I adb devices, however it does show in device manager. This changed after trying to do the RUU without relocking.
Click to expand...
Click to collapse
Not sure whats up with that, never had any issue on win7.
Windows 8 fastboot works on my laptop for some reason. I installed the drivers from the HTC Sync folder.
Sent from my HTC One S using Tapatalk 2
Related
First of all I apologize if this has been covered, I have been trying to find a solution for 3 days straight. I have a Rogers Wireless HTC One X I managed to unlock bootloader and root as well as having access to TWRP 2.1.8. recovery.
My problem is when I tried to apply the 3 dot removal mod my phone suddenly would not boot past the first screen, and a message would appear for developers use do not distribute but just stay on that screen. I have tried numerous things to no avail. I can boot in recovery and mount sd card from there (but have not found a successful way to restore from within recovery mode) otherwise in fastboot etc. the computer does mount the phone at all. it will not mount as a device properly so I cannot run the RUU and flash to stock.
So I am left with a unmountable and unbootable phone (brick) and have no other ideas on how to fix it if possible. BTW the device does show in device mgr and the computer gives the connect and disconnect alert, but it will not mount. Also, I have read the bootloader has to be relocked to flash back to stock if I relock the phone I cannot access recovery therefore an endless nightmare. Also, within TWRP recovery I try to reboot and it gives an error saying no Android OS found, install a rom or restore from backup (which I have neither) so I have to hold the power and dwn volume button to reboot each time to switch from recovery to fastboot. I think its toast.
Thank you in advance for any responses, I have been up almost 36 hours straight trying to figure this out and the phone is not even a week old. :crying:
There's a link in dev to unofficial twrp with usb mount support install that by following the directions in the thread. Then you'll be able to copy a rom to the phone for flashing.
Or you can install HTC Sync on your computer and that may allow you to use a RUU to flash back to stock. HTC Sync has the required drivers to make a Windows PC recognize the HOX.
gunnyman said:
There's a link in dev to unofficial twrp with usb mount support install that by following the directions in the thread. Then you'll be able to copy a rom to the phone for flashing.
Click to expand...
Click to collapse
Thank you very much I will look into that today. Fingers crossed!
i ran into a similar situation about a week ago. hard shut down the phone by holding down power button for like 10 seconds, then boot into bootloader. hit fastboot. connect your phone to computer, and fastboot oem lock bootloader. now you can ruu. Download Rogers RUU utility and follow steps. Voila! Phone is just like new! but first make sure you still have your old unlock_bin code in case you want to reunlock bootloader.
stnguyen09 said:
Or you can install HTC Sync on your computer and that may allow you to use a RUU to flash back to stock. HTC Sync has the required drivers to make a Windows PC recognize the HOX.
Click to expand...
Click to collapse
Yes, thank you I have HTC Sync installed and it does not recognize the phone when it is connected either. I will keep searching. Thanks.
ethantarheels123 said:
i ran into a similar situation about a week ago. hard shut down the phone by holding down power button for like 10 seconds, then boot into bootloader. hit fastboot. connect your phone to computer, and fastboot oem lock bootloader. now you can ruu. Download Rogers RUU utility and follow steps. Voila! Phone is just like new! but first make sure you still have your old unlock_bin code in case you want to reunlock bootloader.
Click to expand...
Click to collapse
Yes, I have tried relocking bootloader, it did not help with the phone being recognized by the computer also when I oem lock I cannot access recovery and such. I will have some more time to poke around with it, I have downloaded the RUU utility although it sends back error with device not found. Thanks for your reply, I will keep at it I know the phone can not be bricked, well I am hoping not!
I bought a HTC One S for T-Mobile USA. Has been working flawlessly. Today I got an OTA and my world is now upside down. I have spent 5 hours trying countless things to get my phone back up to no avail.
my phone stats:
hboot 1.09.0000
radio 0.16.31501s.16_2
open dsp-v28.1.0.32.0504
emmc-boot apr 2 2012,21:08:24
UNLOCKED
TAMPERED
How do I get back to square one and turn this phone back into something usable?
It has something called TWRP 2.1.7 installed on it and I have tried fastboot and a host of other things to remove it. I have even tried the thread on sending your phone back to stock but I can't access RUU because it won't load the driver. I have never rooted this phone nor do I believe USB Debugging was turned on before I accepted the OTA. I can communicate via fastboot in the command shell via a usb cable. The PC wont mound the SD card so I can't copy a new image and reboot this thing on a different rom and then send it back to stock.
I am about ready to throw it away because i can't seem to get a .zip file to it so it will run again (for putting a working build on it). There are no images to boot to. Somehow that got wiped and no backup was done. I don't give a poop if the data is whiped. Its all backed up via dropbox and exchange. I just want it up and running so i can use RUU and send it back to stock.
Any help would be appreciated.
Scuba_Luv said:
I bought a HTC One S for T-Mobile USA. Has been working flawlessly. Today I got an OTA and my world is now upside down. I have spent 5 hours trying countless things to get my phone back up to no avail.
my phone stats:
hboot 1.09.0000
radio 0.16.31501s.16_2
open dsp-v28.1.0.32.0504
emmc-boot apr 2 2012,21:08:24
UNLOCKED
TAMPERED
How do I get back to square one and turn this phone back into something usable?
It has something called TWRP 2.1.7 installed on it and I have tried fastboot and a host of other things to remove it. I have even tried the thread on sending your phone back to stock but I can't access RUU because it won't load the driver. I have never rooted this phone nor do I believe USB Debugging was turned on before I accepted the OTA. I can communicate via fastboot in the command shell via a usb cable. The PC wont mound the SD card so I can't copy a new image and reboot this thing on a different rom and then send it back to stock.
I am about ready to throw it away because i can't seem to get a .zip file to it so it will run again (for putting a working build on it). There are no images to boot to. Somehow that got wiped and no backup was done. I don't give a poop if the data is whiped. Its all backed up via dropbox and exchange. I just want it up and running so i can use RUU and send it back to stock.
Any help would be appreciated.
Click to expand...
Click to collapse
I hate to tell you this but if you never unlocked or rooted your phone, somebody did. Your device is unlocked and running a custom recovery therefore you cannot accept over the air updates and that is your problem. You did not buy your phone that way from T-Mobile so what did you really do to get to this point?
Behold_this said:
I hate to tell you this but if you never unlocked and rooted your phone, somebody did. Your device is unlocked and running a custom recovery therefore you cannot accept over the air updates and that is your problem. You did not buy your phone that way from T-Mobile so what did you really do to get to this point?
Click to expand...
Click to collapse
I never said I bought it as OEM. I also never thought to ask the guy I got it from if he rooted it or unlocked it.
Relocking the boot loader then running an RUU should fix the issue. Once you do that enter the recovery and wipe everything/factory reset.
Then if you are trying to run a custom ROM you should be able to mount your SD card and push one to the phone.
Sent from my HTC One S using xda premium
beats4x said:
Relocking the boot loader then running an RUU should fix the issue. Once you do that enter the recovery and wipe everything/factory reset.
Then if you are trying to run a custom ROM you should be able to mount your SD card and push one to the phone.
Sent from my HTC One S using xda premium
Click to expand...
Click to collapse
Great reply however I am short on knowledge on how to do what you have recommended. I don't know how to relock the boot loader nor can I run RUU because I can't get the driver installed. Any help would be awesome. Thank in advance. Sorry I'm a noob at this.
In the dev section there is an all in one toolkit that will execute the correct scripts for you. Download it, then run it. You may also need the HTC sync drivers installed on your computer.
Once you see that the bootloader is locked run the ruu.
And don't apologize for being a noob, I am too lol. We all need help to get started.
Sent from my HTC One S using xda premium
If you install HTC sync to your pc it should install the driver's you need. Then install the one s tool kit in developers section to relock. Then run ruu.
Also, anything you see in blue text is what you'll need to type, or copy/paste, to avoid any quote confusion.
Files You Need:
T-Mobile USA RUU file (mirror) - it's about 563 mb, and worth saving once you download it.
Extremely Important: If you're on another carrier you'll need a different RUU file - DO NOT try and run this RUU file, it could really screw you up. Go to this link to find the right RUU file.
HTC Drivers (mirror) - You probably already have the drivers installed if you're needing this thread, but just in case...
ADB / Fastboot (mirror) - same as the drivers, but again, just in case...
Initial Setup:
Again, some of this might be redundant as you might already have this setup if you rooted/unlocked.
Install the HTC drivers if you haven't already
Unzip the adbfastboot.zip file to your desktop (anywhere, but I find it easiest to get to it on the desktop for my habits)
Getting into the bootloader (hboot):
If you're stuck in a boot loop, pull the batt... oh wait, we can't do that here. To perform a hard reset, hold down the power button for 10 seconds - in the process you'll see the softkeys start blinking, then it should reset. As soon as it starts to reset, release power, and hold down the volume-down button - hold it until hboot pops up (white screen, colored text).
If you're phone is fully powered off (make sure "fastboot" is disabled - settings > power), hold the volume-down key and while holding it, press and hold power for a few seconds. You can probably release the power button, just make sure you keep holding volume-down - after probably 3-5 seconds (maybe a bit more), hboot should come up.
If the phone is on and you're plugged in to your computer, make sure "usb debugging is enabled" (settings > developer options), shift+right-click the adbfastboot directory on your desktop (or wherever you put it), choose "open command window here", and in the prompt that comes up, input adb reboot bootloader.
Restoring:
Once you're in hboot, make sure you select Fastboot (if you don't see it, you're in Fastboot already). In the command prompt referenced above, input fastboot oem lock. This will relock your bootloader in order to allow the RUU to run. Historically this has been necessary for an RUU to run, but I haven't actually tested it without relocking on the One S, and assumed based on previous HTC devices that this would continue to be the case. Edit: thanks rbrookstx for confirming that re-locking is necessary
Your phone will reboot when it relocks - follow the steps above to get back into hboot.
Once you're back in hboot, make sure you're in Fastboot, and open / run the RUU file. It'll go through some initial prompts, then it should start. It takes about 10-15 minutes, maybe less, depending on your computer.
Once it's done, it'll simply go back into hboot - reboot, and you're good to go.
A couple of notes:
When you unlocked and flashed a custom recovery (if you did that), hboot probably said "tampered with" and when it booted up, it probably had a red message under the "HTC" logo about being a developer only device. That should be gone now. It should boot up clean, and hboot should simply say "relocked", with no tampered message.
Until a better solution comes out, once you unlock the bootloader with HTC's official method, it can never be locked the way it was from the factory. "Relocked" is the best you can do.
Click to expand...
Click to collapse
This is what worked. I had to search the internet for this stuff but the HTC driver, the fast boot and the RUU with a matching or higher radio number all made it work out.
As the title says, RUU attempts booting my phone but it never comes back on. Even selecting restart boot loader in fastboot or a command it doesn't power itself back on. I have read through other forums and nothing has worked for me yet.
EDIT: I should probably clarify fastboot usb WORKS. Ruu must see my phone considering it detects the ROM version and turns the phone off in attempt to reboot. Anything that I do that requires a reboot doesn't work. I have tried unlocking the bootloader again, everything is fine until it comes to rebooting then I must turn the phone on myself and nothing changes...... IT DOESN'T REBOOT ITSELF therefore seemingly nothing wants to work. And the HTC boot screen is gone??
More background information: http://forum.xda-developers.com/showthread.php?p=39046436#post39046436
What we're your steps exactly? Did you relock your bootloader
a box of kittens said:
What we're your steps exactly? Did you relock your bootloader
Click to expand...
Click to collapse
Yes I did through fast boot with the oem lock command. I've tried installing RUU with a Windows 7 laptop (has HTC sync software) and Windows 8 desktop (basic drivers). Both failed, tried using Windows XP/Vista in compatibility modes and running as an admin with the same results.
Error 171 is a connection error, meaning the RUU can't connect to/find your phone.
Try uninstalling HTC Sync, rebooting your pc, and installing it again. If you've got the Android SDK installed, be sure it's also fully updated.
iElvis said:
Error 171 is a connection error, meaning the RUU can't connect to/find your phone.
Try uninstalling HTC Sync, rebooting your pc, and installing it again. If you've got the Android SDK installed, be sure it's also fully updated.
Click to expand...
Click to collapse
No luck. And I believe it does see the phone in the beginning of the installation. It makes it reboot to the boot loader and that's where it loses the connection. The phone just isn't booting itself back up. I appreciate the reply, if you have anymore ideas please let me know.
Could be something got corrupted. Try redownloading the ruu. Does adb see the phone?
iElvis said:
Could be something got corrupted. Try redownloading the ruu. Does adb see the phone?
Click to expand...
Click to collapse
Re-downloaded RUU and still no go. And adb doesn't see my phone, will it on the fastboot menu? I'm not to familiar with it.
Does anybody else have some more ideas?
Okkoto said:
And adb doesn't see my phone, will it on the fastboot menu? I'm not to familiar with it.
Click to expand...
Click to collapse
No. If adb doesn't see it, fastboot won't either. Does the command "adb devices" (no quotes) show the device as connected?
It sounds like the connection might be working for a few things (like rebooting the phone, as you mentioned). But I still think a connection issue is the main problem.
redpoint73 said:
No. If adb doesn't see it, fastboot won't either. Does the command "adb devices" (no quotes) show the device as connected?
It sounds like the connection might be working for a few things (like rebooting the phone, as you mentioned). But I still think a connection issue is the main problem.
Click to expand...
Click to collapse
Fastboot does see it but adb does not. And what I mean by rebooting the phone in my last post is RUU attempts rebooting it from the boot loader which does turn the phone off but it stays turned off. I've used other commands to reboot the phone from the fastboot screen and those too turn off the phone then again it doesn't come back on like a reboot should do.
I have about completely gave up and going back to using a regular feature phone. I have watched a video about a jtag repair service and was wondering about that or just selling the phone as bricked on ebay.
Okkoto said:
I have about completely gave up and going back to using a regular feature phone. I have watched a video about a jtag repair service and was wondering about that or just selling the phone as bricked on ebay.
Click to expand...
Click to collapse
don't sell it as bricked since it is obviously not bricked. you could get more money just saying you dont wtf your doing and gave up on it. but ill buy it as a bricked phone =) ill give you 50 bucks.
DvineLord said:
don't sell it as bricked since it is obviously not bricked. you could get more money just saying you dont wtf your doing and gave up on it. but ill buy it as a bricked phone =) ill give you 50 bucks.
Click to expand...
Click to collapse
Well if it's not bricked then I sure wish somebody would lead me to the right direction. I have tried 5 different PCs (which all show as connected through fastboot) and they all came with the same error. I've tried everything I could possibly think of and I haven't seen anyone else with quite the same problem I'm having.
I still have not completely gave up and have already decided against selling it as "bricked". The bootloader still comes up so there is at least some hope.
i just had the same problem. the solution was simple - i switch usb-port from front one to the backside one which is directly on motherboard.
Okkoto said:
Well if it's not bricked then I sure wish somebody would lead me to the right direction. I have tried 5 different PCs (which all show as connected through fastboot) and they all came with the same error. I've tried everything I could possibly think of and I haven't seen anyone else with quite the same problem I'm having.
I still have not completely gave up and have already decided against selling it as "bricked". The bootloader still comes up so there is at least some hope.
Click to expand...
Click to collapse
when you say it shows connected through fastboot what do you mean?
how are you getting the device into fastboot - through recovery??
oh, and what was on your device before you tried loading the RUU?
kkm68 said:
i just had the same problem. the solution was simple - i switch usb-port from front one to the backside one which is directly on motherboard.
Click to expand...
Click to collapse
Yes this + if you're on a usb3 port try usb2. Also make sure you're using the cable that came with the phone as I understand other cables may cause issues like this. Also, avoid using a hub or usb extension.
Solution to error 171
I had the same problem and after many attempts I finally got it to work!
-Uninstall anything HTC related from your computer such as HTC Sync Manager and Drivers. Also delete any HTC folders from your program files.
-Make sure you leave the sdk and adb stuff that you downloaded.
-Connect your device via USB to your computer and let it recognize it. It will automatically install default drivers.
-A pop-up asking to install HTC Sync will appear, just ignore it.
-Make sure you set Fast Boot OFF on your phone, and Debugging ON.
-Leave your phone ON and run the RUU set up.
-Then follow the steps on the wizard and everything should work just fine!
diegoyabishh said:
I had the same problem and after many attempts I finally got it to work!
-Uninstall anything HTC related from your computer such as HTC Sync Manager and Drivers. Also delete any HTC folders from your program files.
-Make sure you leave the sdk and adb stuff that you downloaded.
-Connect your device via USB to your computer and let it recognize it. It will automatically install default drivers.
-A pop-up asking to install HTC Sync will appear, just ignore it.
-Make sure you set Fast Boot OFF on your phone, and Debugging ON.
-Leave your phone ON and run the RUU set up.
-Then follow the steps on the wizard and everything should work just fine!
Click to expand...
Click to collapse
I have a similar problem with my HTC One. I am stuck in the bootloader and any action I take leads straight into a boot loop. If I try to reboot, reboot-bootloader, go into recovery (twrp), or factory reset it goes into a boot loop. Also I can't lock the bootloader and flashing my recovery doesn't help, even though it says its a success. I've tried three computers and deleted and reinstalled drivers but still the computers only find my phone in fastboot usb and can't find it using adb.
This solution above won't help me since I can't get my phone on for the life of me. I tried running RUU and All-in-One Toolkit but no luck. RUU fails finding the bootloader since my phone gets stuck in its boot loop. I am fresh out of ideas so any other ways to fix this issue would be greatly appreciated.
BTW I found my phone is this condition when I pulled it out of my pocket. I never installed custom ROMs on it. It is unlocked and rooted though running 4.2.2 (3.05.651.6) hoot 1.55. The only thing I can think of is that an OTA update got pushed to my phone and bricked it. That or for some strange reason something went wrong with phone from the rooting process after two weeks of it working perfectly.
jondon156 said:
I have a similar problem with my HTC One. I am stuck in the bootloader and any action I take leads straight into a boot loop. If I try to reboot, reboot-bootloader, go into recovery (twrp), or factory reset it goes into a boot loop. Also I can't lock the bootloader and flashing my recovery doesn't help, even though it says its a success. I've tried three computers and deleted and reinstalled drivers but still the computers only find my phone in fastboot usb and can't find it using adb.
This solution above won't help me since I can't get my phone on for the life of me. I tried running RUU and All-in-One Toolkit but no luck. RUU fails finding the bootloader since my phone gets stuck in its boot loop. I am fresh out of ideas so any other ways to fix this issue would be greatly appreciated.
BTW I found my phone is this condition when I pulled it out of my pocket. I never installed custom ROMs on it. It is unlocked and rooted though running 4.2.2 (3.05.651.6) hoot 1.55. The only thing I can think of is that an OTA update got pushed to my phone and bricked it. That or for some strange reason something went wrong with phone from the rooting process after two weeks of it working perfectly.
Click to expand...
Click to collapse
Nobody here can help you as we don't have any experience with your device. You'd be much better off asking in the HTC One forum which you'll find here:
http://forum.xda-developers.com/htc-one
Sent from my Evita
Heisenberg said:
Nobody here can help you as we don't have any experience with your device. You'd be much better off asking in the HTC One forum which you'll find here:
http://forum.xda-developers.com/htc-one
Sent from my Evita
Click to expand...
Click to collapse
hi all..
facing same problem with HTC Desire 816 n 4g... have anyone got any solution??
plz pass it..
thank you
Hi there,
i have a huge problem. As there was no warrenty left for my One S I thought about to change the firmware to CM11.
I have to admit that i don't have any experience in doing such things, but i thought, it couldnt go wrong if i follow a tutorial.
So at first i unlocked the bootloader via HTC website and istalled TWRP 2.7.1 (latest version). Everything went well, I placed the ROM into the phones root directory, started the recovery and then whiped it before choosing install and selected the file. After about 30 seconds the phone reported the step was successful and i pressed reboot. Then there was the HTC starting screen and then a black screen.
After that i had no reaction but the blinking buttons when i press the power button for a longer time. But it changes nothing. No normal boot. No access to fastboot. Only if i connect it to my PC there is an aditional device to see, but whitout any access.
I know I did wrong but i have no idea what or how to fix it. I hope you can help me.
ElDorado1993
Now i found a way to get access to fastboot again, but i dont really know what to do now.
Can you give me an detailed tutorial, for jelly bean or kitkat (dont matter) that is surely working now?
My main problem is that i can't copy my files into the root directory as i cant boot the phone.
Does it show up in computer connected devices?
If it does, download stock kernel and ROM and upload to phone and go into recovery[power +volume up while off] and flash them both kernel first.
Sent from my ZTE_N9511 using XDA Free mobile app
The problem is the phone wasnt ever shown as device on the pc (like a flash drive) since version 4.1 so I allways needed some tricks like airdroid. So i suppose i need adb commands to copy files and i dont have so much experience in doing this.
Do you know how to use adb?You don't need adb I just wanted to know to see if it shows up there and not on computer you simply need to install the drivers.Try holding down all 3 buttons to see if it powers down. Do what it says http://www.technewscentral.co.uk/enter-fastbootbootloader-mode-htc-one/id_7930 if works go into fast boot. Does it say locked or unlocked. If unlocked go herehttps://github.com/koush/UniversalAdbDriver and get the windows installer if your on windows.
Sent from my ZTE_N9511
I now found out how adb and fastboot are working, but the main problem now is, that it says the sdcard cant be mounted. I tried this tutorial http://forum.xda-developers.com/showthread.php?p=25557817#post25850720 but i dont know how to do the first step. Du i need an extra file and where do i get it from and how to use it. As long as i dont get back this access, i couldnt install any OS. I tried also sideload. It was able to copy but cant install because of the missing sdcard access.
I hope you can help me to become my phone running again.
Go here http://m.youtube.com/watch?v=xWmnHwkDrKk but first type adb devices in cmd. If it shows ur HTC type adb shell and and type mount sdcard next to the "#" once it appears although you should be using the fastboot shell not adb commands.adb should only work on a powered on device or you can use fast boot in cmd while phone is in fastboot not recovery(you did say the phone can go into fast boot right?). Just make sure you got the right drivers and both fast boot and adb. You should get Koush's Universal drivers from my previous post since some phones have multiple drivers and MAY cause problems with cmd. Also HTC one S doesn't have expandable storage correct?
Sent from my ZTE_N9511
Wow. Now I incidentally soft bricked my phone again if you would believe it and nothing works this time.
Have you been able to fix?
Sent from my ZTE_N9511
Okay, i forgot to write but adb and fastboot are working on my Mac. I use the Mac because Win 8.1 has the known driver problems.
I tried a lot now, but i recognized maybe the main problem. My phone is still S-ON in bootloader. For sure thats the problem. Do I need to get rid of it and how do I do. The tutorial i used hasn't mentioned this step, maybe the person was still S-OFF.
The first thing i try now is to flash the original recovery, lock the bootloader and execute the original signed RUU to get back the original software first. Im going on holiday on tuesday and it would be a pitty without the phone. When I get it working i will leave it, and thy it again, when I'm back. Otherwise.......****
Use this tutorialhttp://htc-one.wonderhowto.com/how-to/fix-soft-bricked-htc-one-by-flashing-new-rom-via-adb-0154361/unless its the one you used already. From boot loader you were supposed to have gone to fastboot.boot loader has to be unlocked.From fast boot you flash TWRP.IMG which happens to have a special adb side load feature under advanced options. There you upload another ROM and kernel.here is the full list of supported devices as I don't know what variant or carrier you havehttp://teamw.in/twrp_view_all_devicesAlso, a stock kernel is optional but it always seems to fix my problems.
Sent from my ZTE_N9511
Thank you. But I already did it like this. The issue is, than after using sideload successfully the installation fails because of the known "unable to mount storage" text. And i don't know what to do wrong.
Like I already said, my phone is still S-ON, but can this make a difference?
Now i got it to bring the stock ROM running again, and as I'm on holiday for a few days I'm happy it is working again.
But one thing is left. It seems like there is no 3G/HSDPA connection now, only EDGE. I dont know what went wrong. Did you hear about this problem.
By the way, my phone is the standalone version whithout any provider.
Search the forums about edge only. There is a huge thread on this.
So, I wanted to go to the newly released snapshot of CM12, so I decided to update my TWRP as well. Turns out, that was a terrible mistake, because not only did it not work (so I can't go into recovery), but I believe I soft-bricked my phone, because I cannot boot into it regularly. I can still go into the bootloader (which means I can use ADB), but that's it. Hitting recovery in the bootloader is an infinite screen, and booting regularly is an infinite screen. I followed this video: https://www.youtube.com/watch?v=9HWj_1KHbuY . After it didn't work, I did a command that cleared the cache of my phone, and tried the same thing again. Now my phone is not working, and I'm going to cry myself to sleep. Please help.
Right now I am on a Mac that I've never used ADB on before, so it doesn't recognize my phone, so I cannot use it. If there is a way around confirming the ADB connection from my phone and forcing ADB to work with it, that would be good to know. I will be back to my PC that knows my phone on Sunday, so I can do that then.
Is an RUU the best thing to do? I'm fine with losing everything on the phone.
Hmm i installed the latest verison of twrp with my mac via fastboot ( followed directions from twrp site for the commands). I would try to get adb/fastboot to work on your mac first and maybe try to fastboot flash twrp again? and if that does not work i would just do a RUU honestly, but i'm sure someone smarter than me can chime in and get it resolved . For instructions to install adb/fastboot on a mac i followed this http://htc-one.wonderhowto.com/how-...-mac-os-x-send-commands-your-htc-one-0151178/ If it does not recognize your device try installing htc sync manager.
darthnix said:
So, I wanted to go to the newly released snapshot of CM12, so I decided to update my TWRP as well. Turns out, that was a terrible mistake, because not only did it not work (so I can't go into recovery), but I believe I soft-bricked my phone, because I cannot boot into it regularly. I can still go into the bootloader (which means I can use ADB), but that's it. Hitting recovery in the bootloader is an infinite screen, and booting regularly is an infinite screen. I followed this video: https://www.youtube.com/watch?v=9HWj_1KHbuY . After it didn't work, I did a command that cleared the cache of my phone, and tried the same thing again. Now my phone is not working, and I'm going to cry myself to sleep. Please help.
Right now I am on a Mac that I've never used ADB on before, so it doesn't recognize my phone, so I cannot use it. If there is a way around confirming the ADB connection from my phone and forcing ADB to work with it, that would be good to know. I will be back to my PC that knows my phone on Sunday, so I can do that then.
Is an RUU the best thing to do? I'm fine with losing everything on the phone.
Click to expand...
Click to collapse
You could go find the ruumode-flashable recovery that I think is in one of dottat's ruu threads (5.0.1 one I think). Then change the name of the file to 0p6bimg.zip and flash it in bootloader. That should flash twrp to a phone without adb/fastboot.