Hi Guys
My Phone bricked itself. I suddenly started to get in a bootloop all by itself. I tryed using zhingmings method on restoring stockrom
I couldn´t find a german one so i took the austrian, but i guess this is not a problem- is it?
I have acces to clockwork mode but if i try to make a factory reset it also just keeps restarting.
So when i try flashing the rom via odin i think it does nothing of worth i get this message
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9100JPLPF_I9100OJPLPC_I9100XXLPX_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9100JPLPF_I9100OJPLPC_I9100XXLPX_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> All threads completed. (succeed 0 / failed 0)
Also is there a way to turn of my phone. If i longpress power it just starts rebooting.
Your help is much appreciated.
Either you are in the wrong forum, or you are flashing the wrong rom....
So ask your question in the 9100 forum, or flash a P6800 rom
Good luck
May I know if you are using P6800 or I9100? Coz from the msg you posted you are flashing I9100 firmware. If you are using P6800, it will not work. It also might make things worst...
Sent from my GT-P6800 using xda app-developers app
Related
I followed a tutorial because its looked the best i had seen for a while and it had most the files included it was off this forum in the developers section so i booted my s5300 into download mode started up odin 3 and begin placing the files in the correct paths. Once in the correct paths i pressed start and here is what i get a fail? can anyone explain why this might be happening i think the old owner who gave me the brick said he had partioned it so he could use a custom rom ive booted into recovery mode and i see is it cyanmobile amd clockworkmod but i think the clockwork dont have any files? and something else anyway here is the code of the odin result any help would be very helpful has ive been up all night trying to repair it to no avail i dont know how much more i can take hehe?:laugh:
EDIT: might be worth mentioning it does still have a custom rom on the partition i can successfully install it boot when i reboot it just says onkey 7s reset?
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> PDA_S5300_XXLF5.tar.md5 is valid.
<OSM> MODEM_S5300_XXLF5.tar.md5 is valid.
<OSM> CSC_S5300_BTULF1.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Complete(Write) operation failed.
<ID:0/004> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
pablo77777 said:
I followed a tutorial because its looked the best i had seen for a while and it had most the files included it was off this forum in the developers section so i booted my s5300 into download mode started up odin 3 and begin placing the files in the correct paths. Once in the correct paths i pressed start and here is what i get a fail? can anyone explain why this might be happening i think the old owner who gave me the brick said he had partioned it so he could use a custom rom ive booted into recovery mode and i see is it cyanmobile amd clockworkmod but i think the clockwork dont have any files? and something else anyway here is the code of the odin result any help would be very helpful has ive been up all night trying to repair it to no avail i dont know how much more i can take hehe?:laugh:
EDIT: might be worth mentioning it does still have a custom rom on the partition i can successfully install it boot when i reboot it just says onkey 7s reset?
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> PDA_S5300_XXLF5.tar.md5 is valid.
<OSM> MODEM_S5300_XXLF5.tar.md5 is valid.
<OSM> CSC_S5300_BTULF1.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Complete(Write) operation failed.
<ID:0/004> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Have you tried this:
http://forum.xda-developers.com/showthread.php?t=2560314
Hi there, as you can tell from the title, my phone is stuck in a bootloop at the AT&T symbol and keeps vibrating in about 15 second increments. I tried flashing the stock ROM to the phone, but every time that I flash all the files attained from https://forum.xda-developers.com/verizon-galaxy-s7/how-to/how-to-notes-root-install-xposed-unroot-t3411039 . Under the ATT_G930AUCS2APF2.zip file. I extract it and get all 4 files in which I have to use ODIN to flash. I load all of them in ODIN and I whenever I try running it, it fails. This is the log
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1203)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I'm running ODIN in administrator, I'm on Windows 10 and I've used both Prince Cozmy ODIN and the regular 3.1.2 release.
Any help in getting it out of the boot loop would be greatly appreciated.
Based version of my s7 is G930FXXU1DQG2 .so i found out it is from Brazil.. I bought it in Croatia and knox was already tripped. Still i have 7.0 and no official update for 8.0 is available.. currently phone is not rooted. How can i upgrade to 8.0 and which way is safest ? I apreciate evety help and sorry if my english is not so great
sams7 said:
Based version of my s7 is G930FXXU1DQG2 .so i found out it is from Brazil.. I bought it in Croatia and knox was already tripped. Still i have 7.0 and no official update for 8.0 is available.. currently phone is not rooted. How can i upgrade to 8.0 and which way is safest ? I apreciate evety help and sorry if my english is not so great
Click to expand...
Click to collapse
Download Samsung Smartswitch to your pc, plug the phone in and let Smartswitch update
cooltt said:
Download Samsung Smartswitch to your pc, plug the phone in and let Smartswitch update
Click to expand...
Click to collapse
i am not sure if you understand me. It says that software is already updated. i did what u sugested but i am still on andorid7.0 and smartswitch cant help.
https://www.sammobile.com/firmwares/galaxy-s7/SM-G930F/ZTO/download/G930FXXU1DQG2/179848/ as u can see on this link this version which i have still has 7.0
sams7 said:
https://www.sammobile.com/firmwares/galaxy-s7/SM-G930F/ZTO/download/G930FXXU1DQG2/179848/ as u can see on this link this version which i have still has 7.0
Click to expand...
Click to collapse
Ok, make sure development options are enabled then OEM unlock is enabled. Down load odin and the latest unbranded Oreo from sammobile and flash.
Do you know how to do any of this?
cooltt said:
Ok, make sure development options are enabled then OEM unlock is enabled. Down load odin and the latest unbranded Oreo from sammobile and flash.
Do you know how to do any of this?
Click to expand...
Click to collapse
Yes i do..already installed odin and downloaded some firmware from some tutorial on youtube and proces failed. Here is what odin has done :<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1301)..
<ID:0/004> File analysis..
<ID:0/004> Total Binary size: 4071 M
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Can't open the specified file. (Line: 1892)
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
it took only few seconds and this happend and stopped the proces.
So i decided to download this firmware and try again : https://www.sammobile.com/firmwares/galaxy-s7/SM-G930F/ZTO/download/G930FXXS3ERLA/250062/
Is it better to try with this one or should i find another.
sams7 said:
Yes i do..already installed odin and downloaded some firmware from some tutorial on youtube and proces failed. Here is what odin has done :<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1301)..
<ID:0/004> File analysis..
<ID:0/004> Total Binary size: 4071 M
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Can't open the specified file. (Line: 1892)
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
it took only few seconds and this happend and stopped the proces.
So i decided to download this firmware and try again : https://www.sammobile.com/firmwares/galaxy-s7/SM-G930F/ZTO/download/G930FXXS3ERLA/250062/
Is it better to try with this one or should i find another.
Click to expand...
Click to collapse
What country are you actually in?
cooltt said:
What country are you actually in?
Click to expand...
Click to collapse
Currently in Bosnia and Herzegovina. So my phone by the version nubmer is from Brazil,i bought it in Croatia and iam in Bosnia and Herzegovina. a bit crazy
sams7 said:
Currently in Bosnia and Herzegovina. So my phone by the version nubmer is from Brazil,i bought it in Croatia and iam in Bosnia and Herzegovina. a bit crazy
Click to expand...
Click to collapse
OK well because its a G930F you can flash any European firmware on Oreo.
This is the one for your country https://www.sammobile.com/firmwares/galaxy-s7/SM-G930F/TEB
Make sure also to have newest Odin installed ,any older Odin will not be able to flash Oreo stock rom .
As member above said u can install any country based stock firmware for g930f , u don't need oem unlock or debugging on ,it's only for rooting and installing TWRP ect.
Use Uk or Germany ,but u also can use BH,Croatian ect
Pozdrav iz Hrvatske! (Hello from Croatia)
Scorpionea said:
Make sure also to have newest Odin installed ,any older Odin will not be able to flash Oreo stock rom .
As member above said u can install any country based stock firmware for g930f , u don't need oem unlock or debugging on ,it's only for rooting and installing TWRP ect.
Use Uk or Germany ,but u also can use BH,Croatian ect
Pozdrav iz Hrvatske! (Hello from Croatia)
Click to expand...
Click to collapse
Thx , i'll try then with firmware that is for my country ( B&H) . I hope i dont get any error during flashing. Odin is v3.13 so that should do the trick. Only problem is download speed limit on this site,( for free membership is sooo slow ) so i'll get back to you guys later when download is completed.
sams7 said:
Thx , i'll try then with firmware that is for my country ( B&H) . I hope i dont get any error during flashing. Odin is v3.13 so that should do the trick. Only problem is download speed limit on this site,( for free membership is sooo slow ) so i'll get back to you guys later when download is completed.
Click to expand...
Click to collapse
I downloaded firmware,used lates odin and again same error
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1301)..
<ID:0/004> File analysis..
<ID:0/004> skip file list for home binary
<ID:0/004> param.bin
<ID:0/004> modem_debug.bin
<ID:0/004> Home Binary Download
<ID:0/004> Total Binary size: 3949 M
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Can't open the specified file. (Line: 1892)
<OSM> All threads completed. (succeed 0 / failed 1)
What can i do next? :/
You can use updato.com for faster speed or use samfirm app for windows (google it).
Hmm dont know why it is showing in odin cant open specified file.. try different usb cable . Make sure your download is not corrupted ect . Also disable OEM unlock if its enabled
Scorpionea said:
You can use updato.com for faster speed or use samfirm app for windows (google it).
Hmm dont know why it is showing in odin cant open specified file.. try different usb cable . Make sure your download is not corrupted ect . Also disable OEM unlock if its enabled
Click to expand...
Click to collapse
Also try Odin 3.12.7, make sure your not using Windows 8, Use SamFirm tool instead, make sure you have the correct USB drivers for samsung, turn off antivirus software on your pc while you flash.
This error can be many things i'm afraid.
Hey guys
(I have Note 8 SM-N950U ATT unlocked )
I was looking to flash back to the new official android pie (because I went to the OneUI beta and wanted to flash the official one )and I booted into Download mode when I saw
RPMB FUSE BLOWN
RPMB PROVISIONED
and when I try to flash the new android I stuck on download mood and I can't flash any android on my phone.
Please help me.
____________________________________
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1303)..
<ID:0/004> File analysis..
<ID:0/004> Total Binary size: 6768 M
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
Dradka said:
Hey guys
(I have Note 8 SM-N950U ATT unlocked )
I was looking to flash back to the new official android pie (because I went to the OneUI beta and wanted to flash the official one )and I booted into Download mode when I saw
RPMB FUSE BLOWN
RPMB PROVISIONED
and when I try to flash the new android I stuck on download mood and I can't flash any android on my phone.
Please help me.
____________________________________
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1303)..
<ID:0/004> File analysis..
<ID:0/004> Total Binary size: 6768 M
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
Click to expand...
Click to collapse
RPMB FUSE BLOWN is normal and it's blown on everyone's phone.. The second issue is you're probably using the wrong firmware so it's not going to work.. You're supposed to use odin to flash back to the firmware you had before you used the beta pie firmware version.. At this point I would recommend that you odin back to the firmware version you were on before you used the pie version and let the phone automatically OTA update itself!
MrMike2182 said:
RPMB FUSE BLOWN is normal and it's blown on everyone's phone.. The second issue is you're probably using the wrong firmware so it's not going to work.. You're supposed to use odin to flash back to the firmware you had before you used the beta pie firmware version.. At this point I would recommend that you odin back to the firmware version you were on before you used the pie version and let the phone automatically OTA update itself!
Click to expand...
Click to collapse
I have the same error
<ID:0/004> Added!!
<ID:0/004> Removed!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1303)..
<ID:0/004> File analysis..
<ID:0/004> Total Binary size: 4920 M
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Odin stuck here
Dradka said:
I have the same error
<ID:0/004> Added!!
<ID:0/004> Removed!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1303)..
<ID:0/004> File analysis..
<ID:0/004> Total Binary size: 4920 M
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
Odin stuck here
Click to expand...
Click to collapse
Try using a different version of odin look for a newer version or the edited version. Also you need to read this first page about downgrading back..
https://forum.xda-developers.com/galaxy-note-8/how-to/snapdragon-official-note-8-n950u1-t3893612
Something about AT&T being in a boot loop..
MrMike2182 said:
RPMB FUSE BLOWN is normal and it's blown on everyone's phone.. The second issue is you're probably using the wrong firmware so it's not going to work.. You're supposed to use odin to flash back to the firmware you had before you used the beta pie firmware version.. At this point I would recommend that you odin back to the firmware version you were on before you used the pie version and let the phone automatically OTA update itself!
Click to expand...
Click to collapse
MrMike2182 said:
Try using a different version of odin look for a newer version or the edited version. Also you need to read this first page about downgrading back..
https://forum.xda-developers.com/galaxy-note-8/how-to/snapdragon-official-note-8-n950u1-t3893612
Something about AT&T being in a boot loop..
Click to expand...
Click to collapse
I tried many versions of Odin and the same stuck on the Set Partition step , Is that mean I need the PIT file to flash the new firmware?.
I have SM-N950U not SM-N950U1 and I have only Download mode .
SM-N950U doesn't has ATT firmware and when I asked about the stock ATT firmware SamMobile said that I can use USC or CCT firmware .
I don't know how I can fix it .
MrMike2182 said:
Try using a different version of odin look for a newer version or the edited version. Also you need to read this first page about downgrading back..
https://forum.xda-developers.com/galaxy-note-8/how-to/snapdragon-official-note-8-n950u1-t3893612
Something about AT&T being in a boot loop..
Click to expand...
Click to collapse
I used Odin 3 (Odin Prince Comsy) and I has this error
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1203)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> FAIL! Model dismatch fail
<OSM> All threads completed. (succeed 0 / failed 1)
Dradka said:
I used Odin 3 (Odin Prince Comsy) and I has this error
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1203)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> FAIL! Model dismatch fail
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Yes you need the PIT file it's the CSC file just extract that one file and not all of them and then in odin options add the PIT file and then in the other options select re-partition and also Nand erase all and then try. Make sure you're using N950U firmware ONLY and NOT N950U1!! By the way at the very end of the files you're flashing DELETE the part at the end of it the .md5 part so it only says .tar
MrMike2182 said:
Yes you need the PIT file it's the CSC file just extract that one file and not all of them and then in odin options add the PIT file and then in the other options select re-partition and also Nand erase all and then try. Make sure you're using N950U firmware ONLY and NOT N950U1!! By the way at the very end of the files you're flashing DELETE the part at the end of it the .md5 part so it only says .tar
Click to expand...
Click to collapse
I have this using Odin3 v3.13
I have this using Odin.Prince.Comsy
Dradka said:
I have this using Odin3 v3.13
I have this using Odin.Prince.Comsy
Click to expand...
Click to collapse
I have no idea what is going on then bro.. Try an older version of odin then? Not prince comsy though you really shouldn't need that.. Try flashing the N950USQS5CRK1 firmware instead. Also try getting into recovery mode and select factory reset if you can.
MrMike2182 said:
I have no idea what is going on then bro.. Try an older version of odin then? Not prince comsy though you really shouldn't need that.. Try flashing the N950USQS5CRK1 firmware instead. Also try getting into recovery mode and select factory reset if you can.
Click to expand...
Click to collapse
Thanks bro.
I don't live in USA now and I have different SIM-card ,Is it necessary to have USA SIM-card to flash the new software?
Dradka said:
Thanks bro.
I don't live in USA now and I have different SIM-card ,Is it necessary to have USA SIM-card to flash the new software?
Click to expand...
Click to collapse
Where did you get the phone from? Is it an actual N950U or is it an N950F? Can you get into recovery mode and get me a screenshot?
MrMike2182 said:
Where did you get the phone from? Is it an actual N950U or is it an N950F? Can you get into recovery mode and get me a screenshot?
Click to expand...
Click to collapse
I don't have recovery mode , I have only download mode .
I was having the phone brand SM-N950U on download mode before this problem and after the problem the brand name gone and replaced with ( Rpmb fuse blown - rpmb provisioned )
This AT&T unlocked phone from USA and I'm sure that its N950U because I flashed many firmware before without problems (Just I have system UI error sometimes ) , and I checked it's IMEI on this site
https://www.imei.info/?imei=358502081255039
and it say that is SM-N950U
I'm not in USA now and Samsung service-care didn't help me and they said they only have service for N950F version .
so really I have a problem and I don't know how to solve it.!!
It sounds like you may have been on the U1 beta. In order to flash U firmware again, you have to use the patched version of Odin:
https://forum.xda-developers.com/android/software/patched-odin-3-13-1-t3762572
datajosh said:
It sounds like you may have been on the U1 beta. In order to flash U firmware again, you have to use the patched version of Odin:
https://forum.xda-developers.com/android/software/patched-odin-3-13-1-t3762572
Click to expand...
Click to collapse
still having the same problem, sadly patched-odin not working too. :crying::crying::crying:
Dradka said:
still having the same problem, sadly patched-odin not working too. :crying::crying::crying:
Click to expand...
Click to collapse
What options are you selecting in odin when you go to try to flash something?
datajosh said:
It sounds like you may have been on the U1 beta. In order to flash U firmware again, you have to use the patched version of Odin:
https://forum.xda-developers.com/android/software/patched-odin-3-13-1-t3762572
Click to expand...
Click to collapse
MrMike2182 said:
What options are you selecting in odin when you go to try to flash something?
Click to expand...
Click to collapse
I selected (Auto Reboot) and (F. Reset Time)
______________________________________________________
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1301)..
<ID:0/004> File analysis..
<ID:0/004> Total Binary size: 4920 M
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
Dradka said:
I selected (Auto Reboot) and (F. Reset Time)
______________________________________________________
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1301)..
<ID:0/004> File analysis..
<ID:0/004> Total Binary size: 4920 M
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
Click to expand...
Click to collapse
Apparently it's failing to re-partition the phone.. You'll need to get the PIT file out of the .tar file that you downloaded and add it in odin and tick re-partition..
MrMike2182 said:
Apparently it's failing to re-partition the phone.. You'll need to get the PIT file out of the .tar file that you downloaded and add it in odin and tick re-partition..
Click to expand...
Click to collapse
I put the pit file but I still having the same problem
__________________________________________
Can I try different model firmware like SM-N950U1?
Dradka said:
I put the pit file but I still having the same problem
__________________________________________
Can I try different model firmware like SM-N950U1?
Click to expand...
Click to collapse
Yes just use the right odin.. Read about it in the N950U1 thread.
nothing work
MrMike2182 said:
Yes just use the right odin.. Read about it in the N950U1 thread.
Click to expand...
Click to collapse
Sadly, nothing work !!!:crying::crying::crying:
Please help..
I reviewed many threads for an answer and posted my question in another thread but failed to get an update.
I am trying to install G935U on G935S. It always fail and couldnt flash the device properly. Also, ROM is in Korean and I want it in English. Please help.
I download the latest firmware from Sam mobile. Below error when using Home_CSC. With CSC_OYM, it stays at Setup Connection and finally fails. Tried with ODIN versions - 3.12.1, 3.12.3, 3.13.1, 3.13.3, 3.13.1_3B_PatcheD, 3.12_PrinceComsy with no luck.
<ID:0/009> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/009> Odin engine v(ID:3.1203)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Set PIT file..
<ID:0/009> DO NOT TURN OFF TARGET!!
<ID:0/009> FAIL!
<ID:0/009>
<ID:0/009> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Can someone please help me??
It appears no one has the know-how to get any of this going on the 935u. So disappointing.......