replaced digitizer - HTC Inspire 4G

I recently replaced my digitizer on my inspire 4g with great success :laugh:, but now my volume button is broken and i have no Wifi :crying: . I am going to go back in and check the connectors, i just wanted to see if my fellow xda users had any similar problems. how much is a new volume flex cable and where is the wifi connector? I have heard that the wifi antenna is the battery door but what about the connector? also when i removed the black square tape covering my mother board there was a bronze metallic sticker underneath that NO One warned me about hence my now broken volume cable, what the heck is it?

Doughboyzilla said:
I recently replaced my digitizer on my inspire 4g with great success :laugh:, but now my volume button is broken and i have no Wifi :crying: . I am going to go back in and check the connectors, i just wanted to see if my fellow xda users had any similar problems. how much is a new volume flex cable and where is the wifi connector? I have heard that the wifi antenna is the battery door but what about the connector? also when i removed the black square tape covering my mother board there was a bronze metallic sticker underneath that NO One warned me about hence my now broken volume cable, what the heck is it?
Click to expand...
Click to collapse
hi when you open the phone you must take the volume flex first because if you dont you break other pieces you dont see now you must put a little piece of flex between the the bottons and the flex and try to press to if works then you put the sticker again so the plastic will not fall that happend to me and thats how i resolve the issue... and the wifi check the antenna to see if is disconected i have open a few phones but never had that happend

OK it took me forever but I finally replaced my volume flex cable and now everything is working except the volume down button! Upon further inspection I noticed "electric conducting paint"(similar to the paint on the battery door,simcard and GPS covers) on the interior of the volume button at the top and bottom. on the bottom where the down button touches the flex cable this "paint" has faded thus no volume down. Can I buy this type of paint? I tried a piece of foil but its to tedious to install.
Sent from my Inspire 4G using xda app-developers app

Related

[Q] LCD and touchscreen not working now after disassembly - Connector broken?

I took my TF700 apart last night as the digitizer was not working following a drop and assumed that a cable had come loose.
Anyway, made a mistake while doing it.
I could not disconnect the cables between the LCD and digitizer and the connectors.
I since realise that there is a small white bar that you flip up. I presume I have "broken" the connectors or something as the tablet works fine when plugged into HDMI, but I cannot use the digitizer and the screen does not come on.
Any suggestions? Most that I have found have suggested "throw away and buy again as spares too much", but wondered if anyone had a bright idea.
I have found why the digitizer was not working, there is corrosion over the SD card and around the top connector to the digitizer nearest the SD card slot. It looks like mositure/drip got into the slot and may have shorted something? I have cleaned off the surface debris as much as can.
Anyway this would not impact the LCD which still displayed (until connector concern.)
Following that, is anyone getting rid of their TF700 and would be interested in selling it at a sensible price?
Thanks
If you didn't pull that white bar off or break it, it could possibly be that you have not properly inserted the ribbon cable and fastened the connector. I would open it again and check this before I did anything else.
Most of them work like this:
Open it by pulling at each end of the white bar until it moves foward a little, then gently lift it to about 45 degeres and the cable slides out with a slight tug. Putting the cable back in is the reverse. That bar has to be loose and at about 45 degrees to get the cable back inside the connector. Make sure the end of the cable is in straight and close the connector. Cable should be tight and not come out if you gently tug it.
The OP here may be willing to sell a likely brick:
http://forum.xda-developers.com/showthread.php?t=2769818
flhthemi said:
If you didn't pull that white bar off or break it, it could possibly be that you have not properly inserted the ribbon cable and fastened the connector. I would open it again and check this before I did anything else.
Most of them work like this:
Open it by pulling at each end of the white bar until it moves foward a little, then gently lift it to about 45 degeres and the cable slides out with a slight tug. Putting the cable back in is the reverse. That bar has to be loose and at about 45 degrees to get the cable back inside the connector. Make sure the end of the cable is in straight and close the connector. Cable should be tight and not come out if you gently tug it.
Click to expand...
Click to collapse
Thank you for the suggestions, I have tried that, but none of the 3 connectors (2 for digitizer, 1 for LCD) respond. I connected it to the HDMI, but cannot see the screen respondin to my finger (maybe that is broken also ha ha)
Is it more likely the connector, or cable is broken? I suspect connector pins to be honest. Abit small for me to see though.
Digitizer or Ribbon Cable or ZIF socket ??? How to tell ???
dilfred said:
Thank you for the suggestions, I have tried that, but none of the 3 connectors (2 for digitizer, 1 for LCD) respond. I connected it to the HDMI, but cannot see the screen respondin to my finger (maybe that is broken also ha ha)
Is it more likely the connector, or cable is broken? I suspect connector pins to be honest. Abit small for me to see though.
Click to expand...
Click to collapse
Greetings!
Just curious how this problem worked out? I too have a TF700 with a working screen but no digitizer. Some time back during my first battery replacement (another story) I tried (we ARE a curious species you know) to open the ZIF socket for the digitizer cable (has twin, gold ribbons) and accidentally flipped the wrong side... needless to say it did NOT flip open. The black plastic top of the socket broke off exposing a little of the ribbon. Everything still worked fine so I counted myself lucky and closed her up and all was good.
Unfortunately I'm never willing to leave sleeping dogs alone and I attempted to replace the 2nd dud battery with yet another one (don't ever trust those "Brand New" eBay batteries)! This time I must have accidentally pulled on a ribbon cable a bit too much. When I closed up the tablet I ended up with a tablet just like yours... everything works great... just not with my finger! I opened it up AGAIN... to replace the original battery... you never can tell you know... while I was in there I tried reseating the digitizer cables (both sockets)... no luck.
So... now what... I'm hearing that some folks had their digitizers fail after about a year anyway... mine is two years old... so my digitizer COULD have just failed... or it COULD have been my messing with the ribbons and/or ZIF connectors. How to tell ??? Is there ANYTHING one can do short of ordering a replacement ZIF socket PC board ($25 eBay) and / or ribbon? With a two year old device I'm reluctant to spend much on repair... ASUS wanted $184 to fix it... and buying an eBay digitizer or ZIF board on the blind chance that one or the other is the problem seems a bit risky.... to say nothing about the chance of mucking up the heat separation of the LCD/digitizer! What's a digital explorer to do???
The only thing I was unable to determine was where does the forked golden digitizer ribbon cable GO on the glass end. Does THAT end ever come loose? How does it attach to the digitizer? Anything I could "fix" on that end?

[Q] Can I fix this broken connector on my motherboard?

Hi,
The connector on the motherboard that has the flex cable which goes to the smaller board down of the battery is partly snapped off. (imgur.com/BnYn0OZ left side) This also means my screen is disconnected... When pressing on the connector it will still work but when not pressed the screen is just blank. Can I fix this without buying a new motherboard, which is expensive as ****, or am I screwed?
Thanks in advance!
teunko123 said:
Hi,
The connector on the motherboard that has the flex cable which goes to the smaller board down of the battery is partly snapped off. (imgur.com/BnYn0OZ left side) This also means my screen is disconnected... When pressing on the connector it will still work but when not pressed the screen is just blank. Can I fix this without buying a new motherboard, which is expensive as ****, or am I screwed?
Thanks in advance!
Click to expand...
Click to collapse
You can stick something (like little plastic sheets) at the back of that cable, so it is always pushed against back cover.
I fixed a similar problem in my old Canon point and shot digital camera this way
hevangel said:
You can stick something (like little plastic sheets) at the back of that cable, so it is always pushed against back cover.
I fixed a similar problem in my old Canon point and shot digital camera this way
Click to expand...
Click to collapse
Thank you so much!! It works again!

Samsung Galaxy Note Pro 12.2 screen flickering issue solved!

Since changing settings in developer options did nothing for me I checked all the terminals on the black hub soldered to the board with a small precision screwdriver with were all solidly in place so I spliced apart the white battery connector housing to remove completely (this is where the Carson Pro LED Magnavisor from Amazon was a must from Amazon). I then proceeded to attach and solder each battery connector to it's terminal then solder each one in place. the solder job isn't the prettiest but it works, then I cut small pieces of plastic to put in place between the 6 leads, rescrewed the battery down, put the tape back on the connection, fired it up and not one flash or flicker! I'm on 18% battery right now which before would have been going off like the 4th of July. The only thing that perplexes me is that before the fix and booting into recovery, not one flash or flicker but booting back into system and was a flickerfest. I can only guess recovery runs on only a lead or 2.
tjmethod said:
Since changing settings in developer options did nothing for me I checked all the terminals on the black hub soldered to the board with a small precision screwdriver with were all solidly in place so I spliced apart the white battery connector housing to remove completely (this is where the Carson Pro LED Magnavisor from Amazon was a must from Amazon). I then proceeded to attach and solder each battery connector to it's terminal then solder each one in place. the solder job isn't the prettiest but it works, then I cut small pieces of plastic to put in place between the 6 leads, rescrewed the battery down, put the tape back on the connection, fired it up and not one flash or flicker! I'm on 18% battery right now which before would have been going off like the 4th of July. The only thing that perplexes me is that before the fix and booting into recovery, not one flash or flicker but booting back into system and was a flickerfest. I can only guess recovery runs on only a lead or 2.
Click to expand...
Click to collapse
I got the same issue, and yesterday I just unplugged and replugged the battery connector which solved my issue.
But I believe this is temporarly and that I would do a better repair if I do solder.
Thanks for providing pictures.
Ya unfortunately the wire connectors inside the white plastic connector aren't making a tight pinch on the terminals and there is no way to close the distance without getting the white connector out of the way. You could remove the white plastic connector and pinch each one on with needle nose pliers but you might as well solder them on if you go that far. This is why people are having problems replacement tablets- its faulty battery connectors…
luffy092 said:
I got the same issue, and yesterday I just unplugged and replugged the battery connector which solved my issue.
But I believe this is temporarly and that I would do a better repair if I do solder.
Thanks for providing pictures.
Click to expand...
Click to collapse
tjmethod said:
Ya unfortunately the wire connectors inside the white plastic connector aren't making a tight pinch on the terminals and there is no way to close the distance without getting the white connector out of the way. You could remove the white plastic connector and pinch each one on with needle nose pliers but you might as well solder them on if you go that far. This is why people are having problems replacement tablets- its faulty battery connectors…
Click to expand...
Click to collapse
The battery connector with 6 wires only a minor source of flickering screen. You don't need to cut and solder it to the male connector.
The loose connector can be fixed by pushing the opening tip closer like this
Samsung fix it by adding the silver conductive glue like this
The major problem is from the male connector soldered to the mainboard. From my professional experiences, 90 % from cracked male connector ( black with 6 pins and soldered to mainboard ) , only 10% causing by loose female battery connector ( white with 6 wires ) : Samsung just simply use a conductive glue.
Trust me, I have fixed not a few but hundreds of them with this problem.
Great pictures! Well it looks like I am one of the lucky ones- glad I was able to even solder those wires on to the male connector terminals. I did check them- they were solid- I wouldn't have been able to have done it without the Carson LED Magnavisor- its got 4 different interchangeable power lenses. I dont think my tip would have been small enough to heat up the solder on the male connector termials- but I totally believe you most are cracked- glad I havent had a problem since. I have like 5 note tablets and the xe7000t1a windows slate in fact almost everything I own is Samsung including the 17" i7 chronos notebook I'm typing this on. So do you do this sort of thing in the line of business?
Beut said:
The battery connector with 6 wires only a minor source of flickering screen. You don't need to cut and solder it to the male connector.
The loose connector can be fixed by pushing the opening tip closer like this
Samsung fix it by adding the silver conductive glue like this
The major problem is from the male connector soldered to the mainboard. From my professional experiences, 90 % from cracked male connector ( black with 6 pins and soldered to mainboard ) , only 10% causing by loose female battery connector ( white with 6 wires ) : Samsung just simply use a conductive glue.
Trust me, I have fixed not a few but hundreds of them with this problem.
Click to expand...
Click to collapse
tjmethod said:
Great pictures! Well it looks like I am one of the lucky ones- glad I was able to even solder those wires on to the male connector terminals. I did check them- they were solid- I wouldn't have been able to have done it without the Carson LED Magnavisor- its got 4 different interchangeable power lenses. I dont think my tip would have been small enough to heat up the solder on the male connector termials- but I totally believe you most are cracked- glad I havent had a problem since. I have like 5 note tablets and the xe7000t1a windows slate in fact almost everything I own is Samsung including the 17" i7 chronos notebook I'm typing this on. So do you do this sort of thing in the line of business?
Click to expand...
Click to collapse
I used to work at Samsung Repair Center, fixed more than thousands of them
That wouldnt be Intelisol in Fort Worth Tx?
QUOTE=Beut;65498191]I used to work at Samsung Repair Center, fixed more than thousands of them[/QUOTE]
tjmethod said:
Since changing settings in developer options did nothing for me I checked all the terminals on the black hub soldered to the board with a small precision screwdriver with were all solidly in place so I spliced apart the white battery connector housing to remove completely (this is where the Carson Pro LED Magnavisor from Amazon was a must from Amazon). I then proceeded to attach and solder each battery connector to it's terminal then solder each one in place. the solder job isn't the prettiest but it works, then I cut small pieces of plastic to put in place between the 6 leads, rescrewed the battery down, put the tape back on the connection, fired it up and not one flash or flicker! I'm on 18% battery right now which before would have been going off like the 4th of July. The only thing that perplexes me is that before the fix and booting into recovery, not one flash or flicker but booting back into system and was a flickerfest. I can only guess recovery runs on only a lead or 2.
Click to expand...
Click to collapse
I was asking is there any video which shows steps by step on how to do the solder because i want to do that myself
I would check all posts/ threads/ responses from 'Beut'- he's a former samsumg repairman who's repaired thousands of these
[QQUOTE=chumvi;65509217]I was asking is there any video which shows steps by step on how to do the solder because i want to do that myself[/QUOTE]
chumvi said:
I was asking is there any video which shows steps by step on how to do the solder because i want to do that myself
Click to expand...
Click to collapse
Videos won't help if you don't have experiences in soldering. There are many components close to these six pins, without experience and proper solder tip you will cause solder bridges on mainboard. I need a 10x microscope to see clearly what I am doing. You should bring it to a professional , they won't charge much for a 5 to 10 minute re work.
This is the original battery connector with hairline cracks
Then a re soldered battery connector which has more solders added to secure the connections
An experienced tech will routine re work on these two battery connectors first, even the screen is not flickering, because sooner or later it will come back with this problem.
Hi guys,
I didn't want to post in an old thread, but I'm still having trouble with my Note. I took it to a "Pro" to solder the connectors down because the whole thing came off the board somehow. The "Pro" was pretty useless. He left solder all over the place and the tablet was shorting when I picked it up. So I took it back and the photo shows what I ended up with after 4 attempts at fixing the flickering. At this point I've decided to dump the "Pro" and solder the wires directly to the circuit pads. Only one problem - Solder will not stick to the pads no matter what I do. I've tried heating the pads with the iron before applying the solder but it wont stick. I've cleaned the site with alcohol and took off the sticky residue left by the "Pro".
Can anyone see an issue in the photo which might be causing the problem?
Thanks for the help.
---------- Post added at 01:30 AM ---------- Previous post was at 01:30 AM ----------
Hi guys,
I didn't want to post in an old thread, but I'm still having trouble with my Note. I took it to a "Pro" to solder the connectors down because the whole thing came off the board somehow. The "Pro" was pretty useless. He left solder all over the place and the tablet was shorting when I picked it up. So I took it back and the photo shows what I ended up with after 4 attempts at fixing the flickering. At this point I've decided to dump the "Pro" and solder the wires directly to the circuit pads. Only one problem - Solder will not stick to the pads no matter what I do. I've tried heating the pads with the iron before applying the solder but it wont stick. I've cleaned the site with alcohol and took off the sticky residue left by the "Pro".
Can anyone see an issue in the photo which might be causing the problem?
Thanks for the help.
Hi from Spain, i not see the flickering on use, but whem was power off and i chargue apears a flash every 3 or 4 seconds... All time¿Can be the same problem?
Thanks

No reception in some places

Hello! So I have an Nexus 5 D820 and after changing my battery in some areas of my city or my country I don't have any reception. While writing this I popped the battery cover and applied a little pressure with electrical tape to the black wire which I believe is for the reception but I can't tell if I fixed it because most of the time I have reception. So what should I change to fix my reception - only the little black wire or the hole bottom PCB with the plastic cover ? Thanks in advance!
Since it's working at some places it's probably not your device's fault that it can't connect at some other places. Nevertheless:
To change your battery you must have removed the motherboard cover to remove the battery cable. The GSM antenna is on the motherboard cover and is connected by simply touching 2 small conductive pieces on the motherboard (with the phone facing down and the motherboard cover removed, these should be at the top right area of the motherboard). There are also 2 wires (along with a big wire strip) that connect the 2 bottom edges of the motherboard to an extra little board below the battery (where the USB port and other components are). Those are antenna extensions, one of these is probably the black wire you are talking about. The right one is for 3G and the left one is for 4G (with the phone facing down), don't remember the colors. If you have a problem with data connection and not normal cell reception, check those 2 wires. The 3G and 4G antennas are on the black plastic cover of that extra little board and connect to it with a similar way the GSM antenna connects to the motherboard (each one has 2 gold flexible metal pins). You didn't need to remove that plastic cover to replace the battery, but if you did, remove it again and check the connector and those gold pins.
Whatever you do: NEVER DO ::ANYTHING:: WITHOUT DISCONNECTING THE BATTERY (xp talking).
Shutdown the device normally, remove back cover, remove motherboard cover, disconnect the battery cable, and THEN do whatever you have to do.
The screwdriver is usually metal and can short things. You really don't want to short something on the motherboard with the battery connected.
Thanks! I started losing signal after I replaced my battery(before that no problems whatsoever), but couple of days ago I opened the phone again and applied a little pressure to the both wires and I hope it's fixed. Also today I'm going to the place where I'm losing signal and I will find out.

Nexus 5 LG Repair Question

Hey XDA, a quick question, what part of a phone connects the display to the board?
With the back of the phone facing you, the LCD cable connects to the motherboard connector located in gene upper right hand corner. Not sure if this is what you wanted to know.
its on the bottom flex, display+digi is connected on that flexible board thag connects to the logic board near the camera, but that flex is so ****ty and after a few reconnections ull eventually break the flex tray and ull have to hotfix it with tape and plastic, be careful.
Sent from my Nexus 5 CAF using Tapatalk
It's one the bottom? I know there are two connections at the bottom of the motherboard but isn't one for the battery and the other is for the USB charging port, speaker, mike, etc? When I replaced a screen, I had to transfer the USB charging cable to the new screen.
audit13 said:
It's one the bottom? I know there are two connections at the bottom of the motherboard but isn't one for the battery and the other is for the USB charging port, speaker, mike, etc? When I replaced a screen, I had to transfer the USB charging cable to the new screen.
Click to expand...
Click to collapse
right, and that one also connects disp+dig with the mobo, if u dissasembly the plastic bumper at the bottom ull find two antennas, one by side, a mic, the speaker and the screen & touch connector
Sent from my Nexus 5 CAF using Tapatalk
Gosh I hated having to replace my screen, it was a nightmare!

Categories

Resources